MODEL H7725
84" EURO STYLE
WORKBENCH-BIRCH
INSTRUCTIONS
assembly
refer to the last page of these instructions to
inventory your shipment for ease of assembly.
To assemble the workbench:
1. insert eight (e5) barrel nuts into panels (LF &
LB), and assemble the drawer with eight (e1)
screws in the orientation shown in figure 2.
E2
E1
H7
LL
figure 1. model h7725 Birch Workbench.
E5
Specifications
LF
Finish..........................................Lacquer sealed
table thickness ...............................................4"
Front Vise size .....................................193⁄4" x 7"
end Vise size ............................................6" x 6"
overall size ..............841⁄2"W x 2411⁄16"d x 341⁄4"h
tilt-out drawer size .........531⁄2"W x 19"d x 14"h
storage shelf size.....................551⁄2"W x 181⁄2"d
shipping Weight ......................................332 lbs.
H8
BP
LB
LR
E5
E1
figure 2. tilt-drawer assembly.
2. position the right side leg (B) on the floor
so the Front arrow points to the front and
install two barrel nuts (e4) into cross brace (d
& e) as shown in figure 3.
Safety & Limitations
•
•
•
maximum workbench table load is 500 lbs.
do not stand or climb on the workbench.
do not apply an unbalanced load on the table
that could result in the workbench tipping
over.
•
Keep unsupervised children away from the
workbench.
B
Front
•
•
do not stand or climb on the workbench.
do not use workbench outdoors or in wet or
damp locations.
Slot
E3
•
•
do not overload the vises or use cheater
pipes on the vise handles to increase lever-
age.
E2
E4
D
Note: Slot
for Lock
E
do not weld on this bench.
figure 3. right leg and cross brace installation.
Copyright © JULy 2009 By grizzLy indUstriaL, inC.
WaRNINg: NO pORTION Of THIS MaNUaL MaY BE REpRODUCED IN aNY SHapE
OR fORM WITHOUT THE WRITTEN appROvaL Of gRIzzLY INDUSTRIaL, INC.
(For modeLs manUFaCtUred sinCe 7/09) #Cr12019 printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
10. at this time tighten all of the (e3) barrel bolts
except the (e9) barrel bolts used as the
tilting-drawer hinge pins.
17. insert the tail vise wood block into the vise
support block (figure 9). insert the tail vise
leadscrew through the holes in the wood
block and the vise support block at the edge
of the table.
11. With the help of an assistant, return the
workbench to the upright position, and lower
the table top (a) onto the legs making sure
to line up the pre-drilled holes in the legs and
the underside of the workbench.
Vise Support
Block
A
12. Working from the underside of the table legs,
insert four (e8) screws and (e2) washers into
the holes, and use the 4mm hex wrench to
tighten the screws.
Wood Block
J
figure 9. tail vise installation.
13. insert the guide rods and leadscrew through
the holes in the wood block (g) (figure 8).
thread the leadscrew into the vise support
until the wood block is slightly snug against
the table and flush with the table top.
18. turn the tail vise handle clockwise until the
wood block just touches the table, and attach
the vise plate as outlined in Steps 15 & 16.
19. Find the gas spring pins at the drawer under-
side, and install the gas springs (h5) with the
two (h6) screws for each spring (figure 10).
Lead Screw
Guide Rod
Vise Support
Block
Wood Block
A
G
H6
Push shock ends
onto the pins
Flush
D
Wood Block
Flush
G
H5
A
I
figure 10. gas spring installation.
Vise Plate
figure 8. table vise installation.
14. Keeping the wood block flush with the table
5
top (figure 8), drill two ⁄64" holes 17⁄16" deep
through the vise plate mounting holes and
into the wood block.
15. secure the vise plate to the wood block with
two (h1) #5 x 17⁄16" wood screws (figure 8).
16. Under the table, place a cotter pin in the end
of the leadscrew, bending only one cotter pin
leg to a 90 degree angle.
-3-
model h7725 (mfg. since 7/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
parts
parts Breakdown and List
J
a
C
d
F
g
fastener Kit
e
e1
e2
e3
e4
e5
e6
e7
e8
e9
e10
h1
h2
i
Lr
h1
h
h3
h4
h5
h6
h7
h8
LB
B
B
Bp
LF
h4
LL
Lp
fastener Kit part Numbers
REf paRT
DESCRIpTION
QTY
8
e1
ph7725018 BarreL BoLt 2"
ph7725006 FLat Washer
ph7725024 BarreL BoLt 31⁄2
e2
e3
e4
e5
e6
e7
e8
e9
e10
h1
h2
h3
h4
h5
h6
h7
h8
18
8
REf paRT
DESCRIpTION
QTY
1
"
ph7725001 taBLe top
ph7725033 LeFt Leg
ph7725002 right Leg
a
B
C
d
e
F
ph7725025 Large BarreL nUt
ph7725019 smaLL BarreL nUt
8
1
8
1
paW05m
paW04m
heX WrenCh 5mm
heX WrenCh 4mm
1
ph7725026 top BaCK Cross BraCe
ph7725034 top Front Cross BraCe
ph7725040 CaBinet top paneL
ph7725028 Front Vise
1
1
1
ph7725031 Wood sCreW 2"
4
1
1
ph7725014 speCiaL sCreW 1 ⁄2
"
2
1
g
h
i
ph7725032 Cotter pin
2
ph7725029 LWr Front Cross BraCe
ph7725027 LWr BaCK Cross BraCe
ph7725036 taiL Vise
1
ph7725043 Wood sCreW #5 x 17⁄16"
ph7725016 Brass tUBe
4
1
2
1
J
LF
LB
Lr
LL
Bp
ph7725015 LoCK Washer
ph7725020 Key/LoCK set
ph7725010 gas spring
2
ph7725023 draWer FaCe
1
2
ph7725037 draWer BaCK paneL
1
2
ph7725039 draWer right side paneL
ph7725038 draWer LeFt side paneL
ph7725035 Bottom draWer paneL
1
ph7725011 FLat hd sCreW
ph7725008 draWer pULL handLe
ph7725009 speCiaL sCreW 1"
4
1
1
1
Lp
2
g8589
grizzLy Logo pLate
1
-4-
model h7725 (mfg. since 7/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
|