CLASSICAL GUITAR KIT
MODEL H3122
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2003 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#DS3624 PRINTED IN JAPAN. REVISED MARCH, 2006 (TR)
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SECTION 1: SAFETY....................................................................................................................... 2
SECTION 2: INTRODUCTION ......................................................................................................... 3
SECTION 3: PARTS INVENTORY................................................................................................... 4
SECTION 4: SANDING .................................................................................................................... 5
Supplies/Tools............................................................................................................................ 5
Guitar Body ................................................................................................................................ 5
Neck ........................................................................................................................................... 6
Fingerboard................................................................................................................................ 6
Bridge......................................................................................................................................... 6
SECTION 5: ASSEMBLY................................................................................................................. 7
Neck to Body.............................................................................................................................. 7
Fingerboard to Neck................................................................................................................... 8
Bridge/Nut Locations.................................................................................................................. 9
Covered Areas ......................................................................................................................... 10
Painting/Finishing..................................................................................................................... 11
Sound Hole Decal .................................................................................................................... 12
Attaching Bridge....................................................................................................................... 12
Machine Heads ........................................................................................................................ 13
Installing Strings....................................................................................................................... 13
String Height ............................................................................................................................ 14
Tuning ...................................................................................................................................... 16
SECTION 6: REFERENCE INFO ................................................................................................... 17
General..................................................................................................................................... 17
Aftermarket Accessories .......................................................................................................... 17
Warranty & Returns.................................................................................................................. 18
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
Always wear safety glasses or goggles when operating equipment. Everyday glasses or
reading glasses are not safety glasses. Be certain the safety glasses you wear meet the
appropriate standards of the American National Standards Institute (ANSI).
Because there are various ways to cut and join wood, you can make substitutions for the methods
stated in this plan. We try to suggest the easiest methods possible. However, only you know your
skills with each piece of machinery. Never compromise your safety by using a cutting method
with which you are not comfortable. Instead, find an alternative approach that will yield the same
result.
These instructions assume that you are intimately familiar with the safe operation and use of
woodworking machinery and woodworking tools, and understand the techniques used to repro-
duce this project. If you do not qualify for both of these criteria, STOP building this project for
your own safety. Read and understand the owner’s manual for the machinery you intend to use,
take a woodworking class or visit your local library for more information. Woodworking machinery
and tools are inherently dangerous, because they use sharp edges that can and will cause serious
personal injury including amputation and death. Do not underestimate the ability of these tools and
machinery to cause injury. Never operate any tool without all guards in place and always wear
approved safety glasses. For your own safety, please heed this warning.
-2-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INTRODUCTION
We are proud to offer the Model H3122 Classical
Most importantly, we stand behind our products. If
you have any questions or parts requests, please
call or write us at the location listed below.
Guitar Kit. This kit is part of a growing Grizzly fam-
ily of fine woodworking products. When assem-
bled according to the guidelines set forth in this
manual, you can expect years of enjoyment from
this guitar.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
We are pleased to provide this manual with the
Model H3122. It was written to guide you through
assembly, review safety considerations, and
cover general information. It represents our effort
to produce the best documentation possible.
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
The specifications, drawings, and photographs
illustrated in this manual represent the Model
H3122 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of
continuous improvement, changes may be made
at any time with no obligation on the part of
Grizzly. For your convenience, we always keep
current Grizzly manuals available on our website
be reflected in these manuals as soon as they
are complete. Visit our site often to check for the
latest updates to this manual!
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
C
/
O
Bellingham, WA 98227-2069
H3122 Classical Guitar Kit
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: PARTS INVENTORY
101
1
2
103
2
107
104
3
105
106
102
Figure 1. Components.
Figure 2. Hardware.
REF PART #
DESCRIPTION
PH3122001 Guitar Body
PH3122002 Guitar Neck
PH3122003 Fingerboard
REF
PART #
DESCRIPTION
1
2
3
101 PH3122101 Machine Heads W/Fasteners
102 PH3122102 String Set
103 PH3122103 Bridge W/Fasteners
104 PH3122104 Bridge Decoration Sticker
105 PH3122105 String Nut
106 PH3122106 Saddle
107 PH3122107 Dowels
-4-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: SANDING
Supplies/Tools
Guitar Body
The majority of the wooden components in this kit
are fully machined from the factory and are ready
for assembly. A small amount of drilling, sanding
and light machining will need to be performed to
complete the guitar.
The guitar body has been assembled and rough
sanded at the factory; however, no finish has
been applied.
To sand the guitar body:
Recommended Tools & Supplies:
1. Wear an ANSI-approved respirator and
safety glasses when sanding wood!
—Phillips Screwdriver
—Needle-Nose Pliers
—Electric Drill
—Drill Bit Set
—#180, #240, and #320 Aluminum-Oxide
Sanding Paper
—Sanding Block
—Masking Tape
—Painting/Finishing Supplies
—Coat Hanger
2. Usingeitheranelectricpalmsanderorasand-
ing block, sand the guitar body (EXCEPT the
guitar neck notch, the edges, and the sound
hole) with #180 grit aluminum-oxide sand-
ing paper until there is a consistent scratch
pattern on the entire surface. Note—When
hand sanding, always sand in the same
direction as the wood grain.
—C-Clamp
—Tack Cloth
—Coping, Jig, or Scroll Saw (Optional)
3. Sand the guitar body with a #240 grit sanding
paper until there is a consistent scratch pat-
tern on the entire surface.
4. Sand the guitar body with a #320 grit sanding
paper until there is a consistent scratch pat-
tern on the entire surface.
5. Wipe the guitar body with a damp cloth.
Wiping the workpiece with a damp cloth
before the final sanding helps to “raise” the
wood grain; thus, allowing the “raised” grain
to be sanded smooth.
6. Once the guitar body is dry, repeat step 4.
7. Wipe the guitar body with a tack cloth to
remove all remaining sanding dust.
H3122 Classical Guitar Kit
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Neck
Fingerboard
Like the guitar body, most of the guitar neck has
been machined at the factory; however, the neck
headstock can be customized to reflect personal
taste. Additional cutting, inlay, or design work can
give an otherwise ordinary guitar that custom look
that sets it apart from others! Note—Take your
time with this sub-section and consider testing
ideas in scrap wood before performing the work
on the actual headstock.
The fingerboard requires no sanding. Note—
Sanding the fingerboard will affect the playability
of the guitar and could lead to unrepairable dam-
age.
To sand the guitar neck:
Bridge
1. Wear an ANSI-approved respirator and
safety glasses when sanding wood!
The bridge is rough sanded at the factory. Final
sand the bridge as described in the Guitar Body
sub-section.
2. Perform any custom cutting, inlay, or design
work to the neck headstock.
3. Using the sanding technique described in the
previous sub-section, sand the entire guitar
neck, EXCEPT for the fingerboard mount-
ing surface. Note—Sanding the fingerboard
mounting surface will affect the playability
of the guitar and could lead to unrepairable
damage.
-6-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ASSEMBLY
4. Using sandpaper or a file, flatten the neck
Neck to Body
until it is flush with the surface of the body.
5. Before the neck can be glued to the body,
the following must be verified:
Attaching the neck to the guitar body is the most
crucial part of assembling the guitar. Failure to
attach the neck correctly could result in difficult
bridge and string adjustments, or even worse, it
could lead to unrepairable damage.
a. The neck surface and the body sur-
face must be perfectly flat. Note—Use a
straightedge to verify this critical point.
Once the neck is glued to the body, little
can be done to correct mistakes.
To attach the neck to the body:
6. Disassemble the neck and body, and re-
assemble with wood glue. Note—DO NOT
wipe glue squeeze-out at this time! Once the
squeeze-out is dried, remove it with a sharp
chisel.
1. Place the four wooden dowels into the body.
Note—DO NOT use glue at this time!
2. Slide the neck onto the dowels.
3. Using a straightedge, make note of any por-
tion of the neck protruding above the surface
of the body (Figure 3).
7. Once the desired neck position is achieved,
use large rubber bands or a band clamp to
hold the assembly during drying (Figure 4).
10
20
30
40
Figure 3. Checking flatness.
Figure 4. Clamped neck/body assembly.
H3122 Classical Guitar Kit
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Fingerboard to Neck
To attach the fingerboard to the neck:
1. Using a straightedge, make sure the neck
and body surface are flush.
2. Using rubber bands and small sticks of
wood, secure the fingerboard to the neck
with a thin, even layer of wood glue (Figure
5). Note—Make sure the fingerboard is cen-
tered across the width of the neck and that
the 12th fret is centered over the neck to
body joint.
Figure 5. Securing the fingerboard to the neck.
3. After the fingerboard has thoroughly dried,
use a file or sandpaper to make the edge of
the neck flush with the edge of the finger-
board.
-8-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Using a pencil, lightly mark the guitar body
where the front edge of the bridge is locat-
ed.
Bridge/Nut Locations
3. When placed against the end of the finger-
board, the edge of the nut should be exactly
325mm from the center of the 12th fret
(Figure 6).
The correct distances between the inside edge of
the nut, the center of the 12th fret and the center
of the bridge saddle slot are crucial to the perfor-
mance of this guitar. Figure 7 shows the correct
distances.
4. Attach pieces of sewing thread to the 1st and
the 6th nut string slots and tape the opposite
ends over the corresponding string slots on
the bridge.
To determine the correct bridge/nut loca-
tions:
1. Position the center of the bridge saddle slot
exactly 325mm away from the center of the
12th fret (Figure 6).
5. Adjust the bridge so there is an equal amount
of space between the fingerboard edges and
the threads (Figure 7).
Equal
Nut
Distance
325mm
12th Fret
Figure 7. Positioning the bridge across the width
of the guitar.
6. Using a pencil, lightly mark the guitar body
where the side edges of the bridge are
located. Note—DO NOT glue the bridge to
the body at this time.
325mm
Saddle
Slot
Bridge
Figure 6. Saddle slot positioned correctly in
relation to the 12th fret.
H3122 Classical Guitar Kit
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Covered Areas
In preparation for the finish coating, protect
the following parts of the guitar (Figures 8 &
9):
•
•
•
Bridge Mounting Location
Fingerboard
Sound Hole (Hole Filled With Newspaper)
Figure 9. Masked fingerboard.
Use a small stick of wood to carefully press all
the masking tape edges securely to the guitar
pieces. The finish coat can seep under these
edges, especially near corners, uneven edges,
and where the frets meet the fingerboard. Note—
Failure to correctly mask off these areas could
result in unrepairable damage to the guitar.
Figure 8. Masked bridge area and
blocked sound hole.
-10-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Dust particles suspended in the air will settle
on wet finishes, resulting in less than satis-
factory results. To avoid this problem:
Painting/Finishing
1. Leave the finishing room undisturbed for
Finishing supplies are not supplied with the guitar
kit. Note—The guitar body is made from spruce
wood and the neck from poplar wood. Clear fin-
ishes such as lacquer look exceptionally stunning
and glossy on these surfaces.
24 hours prior to applying the finish.
2. Have the guitar components positioned
for the finish application upon entering the
finish room.
Painting/Finishing Tips:
3. Avoid making unnecessary movements
upon entering the finish room.
•
Always work in a well ventilated area
when using finishing materials.
4. Apply the finish and immediately leave
the finish room.
•
Wear an ANSI-approved respirator mask
and safety glasses when using finishing
materials!
5. DO NOT return to the finish room until the
specified drying time has elapsed.
•
•
Fabricate hooks from shirt hangers to sus-
pend the guitar components during the fin-
ishing process.
Several thinner coats usually produce a nicer
finish than one heavy coat. Note—Always
follow the finish manufacturer’s instructions.
H3122 Classical Guitar Kit
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound Hole Decal
Attaching Bridge
To attach the bridge to the body:
To attach the sound hole decal:
1. Remove the masking tape from the bridge
1. Submerge the decal sheet in water until the
clear decal slides around on the paper back-
ing easily with finger pressure. This usually
only takes a few minutes.
location.
2. Apply a thin, even layer of wood glue to the
back of the bridge.
2. Remove the decal sheet from the water, let-
3. Position the bridge on the bridge location
ting the excess water run off.
penciled on the body.
3. Lay the decal sheet over the sound hole.
4. Make sure the bridge is correctly positioned
and let it dry for at least 6 hours.
4. Lightly press down on the decal with damp-
ened fingers and slowly slide the decal sheet
from underneath the decal with the other
hand.
5. Using a 1⁄8" drill bit, drill out the two mounting
holes in the bridge.
6. Secure the bridge to the body with the sup-
5. When the decal sheet is completely removed,
lightly press on the decal with a dry cloth to
remove the excess water trapped under-
neath.
plied screws, washers, and nuts.
7. The heads of the screws can be covered with
the bridge decoration sticker.
-12-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
Machine Heads
Installing Strings
The correct position of the guitar strings are
shown in Figure 11. The thin High E string is
called the “1st” string and the thick Low E string
is called the “6th” string.
The machine heads mount so the buttons are on
the back side of the headstock.
To install the machine heads:
1. Slide the machine heads through the peg
holes on the side of the headstock. Note—
Make sure the lyre end of the machine head
is positioned as shown in Figure 10.
6
5
4
3
2
1
E
A
D
G
B
E
Lyre
Figure 11. Correct guitar string position.
To install the guitar strings:
1. Slide the string ends through the holes in the
bridge.
Figure 10. Correct tuning machine position.
2. Tie the strings as shown in Figure 12.
1
5
4. Using a ⁄16" drill bit, drill ⁄16" deep holes
straight through the screw holes in the
machine heads.
5. Secure the machine heads to the guitar
5
headstock with the included eight ⁄16" wood
screws.
Figure 12. Correct string knots.
(Continued)
H3122 Classical Guitar Kit
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Place the saddle in the bridge saddle slot
and place the nut at the upper end of the
fingerboard. Note—DO NOT glue the nut or
the saddle at this time.
String Height
Correct string height is crucial for maximizing the
playability of your new guitar. The string height is
defined as the distance between the top face of
the fret and the bottom face of the string (Figure
13).
4. Route the string to the inside of the corre-
sponding tuning peg and through the peg
hole. Note—Allow enough string slack to
allow 2-3 complete winds around the tuning
peg.
String
5. Turn the tuning button counter-clockwise
to tighten the string. Note—DO NOT over-
tighten the string. Final string tuning will be
discussed later in the manual.
String Height
6. Use wire cutters to cut off the excess string.
Fret
7. Repeat the above process for the remaining
strings.
Fingerboard
Figure 13. String height measurement
(side view).
Measurements are taken at the following loca-
tions. Note—Use a steel ruler with a resolution of
at least 1⁄64":
•
•
1st fret: 1st string & 6th string
12th fret: 1st string & 6th string
(Continued)
-14-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
To check the string heights of the 1st and 6th
strings at the 1st fret:
To check the string heights of the 1st and 6th
strings at the 12th fret:
Measure the string heights at the 1st fret (Figure
14).
Measure the string heights at the 12th fret
(Figure 15).
6th String: 5⁄64"
Guitar Body
String Nut
6th String: 2⁄64"
1st String: 3⁄64"
12th Fret
1st String: 1⁄64"
1st Fret
Figure 15. Correct 12th fret string heights.
Figure 14. Correct 1st fret string heights.
— If the string heights are correct, then con-
tinue to the next sub-section.
— If the string heights are correct (Figure
33), then move to checking the string
heights at the 12th fret.
— If the string heights are incorrect at the
12th fret, this is an indication that the
groove the saddle sits in needs to be
either deepened or made shallower. This
condition is most likely a result of wood
movement due to humidity changes in
the environment. We recommend having
a qualified guitar technician raise or lower
the saddle before continuing.
— If the string heights are incorrect at the
1st fret, this is an indication that the
groove the string nut sits in needs to be
either deepened or made shallower. This
condition is most likely a result of wood
movement due to humidity changes in
the environment. We recommend hav-
ing a qualified guitar technician raise or
lower the nut before continuing with string
height adjustment at the 12th fret.
H3122 Classical Guitar Kit
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
To tune the guitar:
Tuning
1. Play a known Low E pitch. A piano, a tuning
fork, or an electronic computer file will work.
Tuning is the most important concept of playing a
guitar. If the guitar is not in tune with itself, or the
other instruments in an ensemble, the resulting
music will not sound pleasing to the ear. Having
a good understanding of tuning is essential to
maximizing the full potential of any guitar.
2. Play an open (non-fretted) 6th string. The
goal is to match the open 6th string to the
known Low E pitch.
3. Adjust the tuning peg until the pitch of the
open 6th string sounds exactly like the
known Low E source.
Important issues to consider when tuning a
guitar:
— If the string is tuned too high, back the
tension off and retune the string back up
to match the Low E pitch. Now the other
strings can be tuned to the 6th string.
•
Get into the habit of tuning the guitar every
time it is picked up to be played.
•
Always tune the strings “up.” The final tuned
tension of each string should be reached
while tightening the string, not loosening it.
If the string is tensioned too far, loosen the
tension and tune “up” again.
4. Next, the 5th string needs to be tuned. The
tone of the 5th string must be matched to
the tone of the 6th string by playing the
same note on each string, one after another.
This is done by playing the 6th string while
it is being pressed (fretted) at the 5th fret,
and immediately after, playing the open 5th
string.
•
The goal when tuning is to make the strings
in tune with one another. Standard tuning is
shown in Figure 16.
5. Listen to the two tones. As the two notes are
still resonating, adjust the tuning peg of the
5th string until the two notes have matching
tones. Remember to tune “up.”
6
5
4
3
2
1
E
A
D
G
B
E
6. Perform the same tuning steps on the 4th
and 3rd strings.
7. When tuning the 2nd string, the 3rd string
should be fretted at the 4th fret instead of the
5th fret.
8. Tune the 1st string in the same manner as
the 6th, 5th, 4th, and 3rd strings.
Figure 16. Winding the strings.
•
The easiest way to tune a guitar is using
an electronic tuner such as the Grizzly
H3097 Chromatic Tuner shown on page 17.
However, knowing how to tune a guitar by
ear is an important part of being an accom-
plished guitar player.
-16-
H3122 Classical Guitar Kit
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: REFERENCE INFO
General
Aftermarket
Accessories
This section contains aftermarket accessories
and warranty/return information for the Model
H3122.
If you need parts or help in assembling your
machine, or if you need operational information,
call the service department at (570) 546-9663.
Trained service technicians will be glad to help
you.
If you have any comments regarding this manual,
please write to Grizzly at the address below:
Grizzly Industrial, Inc.
Technical Documentation
P.O. Box 2069
Figure 17. H3097 Chromatic Tuner.
C
/
O
Bellingham, WA 98227-2069
We recommend you keep a copy of our cur-
rent catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Figure 18. H4412 The Guitar Handbook.
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: [email protected]
Figure 19. H4414 Getting Great Guitar Sounds.
H3122 Classical Guitar Kit
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty & Returns
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the
date of purchase. This warranty does not apply to defects due directly or indirectly to misuse; abuse; negli-
gence; accidents; repairs or alterations; assembly, finishing or modification of kits; or lack of maintenance.
This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any
merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written war-
ranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts
unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the
purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_____________________________________________________________________________________
Street_____________________________________________________________________________________
City ______________________________________________________________ State________Zip_________
Phone Number_______________________E-Mail_______________________FAX________________________
MODEL #_______________________________________________ Order #______________________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of
course, all information is strictly confidential.
1.
How did you learn about us?
___Other__________________________________________________
How many of your woodworking machines are Grizzly? _____________
___Advertisement
___Catalog
___Friend
___Card Deck
9.
___World Wide Web
10.
Which benchtop tools do you own? Check all that apply.
___Other__________________________________________________
Which of the following magazines do you subscribe to.
___1" x 42" Belt Sander
___5" - 8" Drill Press
___8" Table Saw
___8" - 10" Bandsaw
___Disc/Belt Sander
___Mini Jointer
___6" - 8" Grinder
___Mini Lathe
___10" - 12" Thickness Planer
___Scroll Saw
___Spindle/Belt Sander
2.
___American Woodworker
___Cabinetmaker
___Practical Homeowner
___Shop Notes
___Family Handyman
___Fine Homebuilding
___Fine Woodworking
___Home Handyman
___Journal of Light Construction
___Old House Journal
___Popular Mechanics
___Popular Science
___Today’s Homeowner
___WOOD
___Wooden Boat
___Woodshop News
___Woodsmith
___Woodwork
___Woodworker
___Woodworker’s Journal
___Workbench
___Other__________________________________________________
How many of the machines checked above are Grizzly? ____________
Which portable/hand held power tools do you own? Check all that apply.
11.
12.
___Belt Sander
___Biscuit Joiner
___Circular Saw
___Detail Sander
___Drill/Driver
___Orbital Sander
___Palm Sander
___Portable Planer
___Saber Saw
___Reciprocating Saw
___Router
___Popular Woodworking
___Other__________________________________________________
Which of the following woodworking/remodeling shows do you watch?
3.
___Miter Saw
___Backyard America
___Home Time
___The American Woodworker
___The New Yankee Workshop
___This Old House
___Woodwright’s Shop
___Other__________________________________________________
What machines/supplies would you like Grizzly Industrial to carry?
13.
___Other__________________________________________________
What is your annual household income?
__________________________________________________________
__________________________________________________________
4.
5.
___$20,000-$29,999
___$30,000-$39,999
___$40,000-$49,999
___$50,000-$59,999
___$60,000-$69,999
___$70,000-$79,999
___$80,000-$89,999
___$90,000 +
14.
15.
What new accessories would you like Grizzly Industrial to carry?
__________________________________________________________
__________________________________________________________
What other companies do you purchase your tools and supplies from?
__________________________________________________________
__________________________________________________________
Do you think your purchase represents good value?
What is your age group?
___20-29
___30-39
___40-49
___50-59
___60-69
___70 +
6.
7.
8.
How long have you been a woodworker?
16.
17.
18.
___0 - 2 Years
___2 - 8 Years
___8 - 20 Years
___20+ Years
___Yes
Would you recommend Grizzly Industrial to a friend?
___Yes ___No
___No
How would you rank your woodworking skills?
___Simple
___Intermediate
___Advanced
___Master Craftsman
Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.
What stationary woodworking tools do you own? Check all that apply.
___Yes
___No
___Air Compressor
___Bandsaw
___Drill Press
___Drum Sander
___Dust Collector
___Horizontal Boring Machine
___Jointer
___Panel Saw
___Planer
19.
Comments:_________________________________________________
___Power Feeder
___Radial Arm Saw
___Shaper
___Spindle Sander
___Table Saw
___Lathe
___Mortiser
___Vacuum Veneer Press
___Wide Belt Sander
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
FOLD ALONG DOTTED LINE
Send a Grizzly Catalog to a friend:
Name_______________________________
Street_______________________________
City______________State______Zip______
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
Download from Www.Somanuals.com. All Manuals Search And Download.
|