Model H7757
3" MINI WOOL BUFFER
OWNER'S MANUAL
COPYRIGHT © DECEMBER, 2005 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JK7772 PRINTED IN CHINA
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SECTION 1: SAFETY.......................................................................................................2
SECTION 2: INTRODUCTION .........................................................................................5
Foreword.....................................................................................................................5
Contact Information ....................................................................................................5
SECTION 3: SET UP........................................................................................................6
Unpacking...................................................................................................................6
Inventory.....................................................................................................................6
Items Needed for Set Up............................................................................................7
Tool Rests ..................................................................................................................7
Eye Shields.................................................................................................................7
Mounting.....................................................................................................................8
SECTION 4: OPERATIONS.............................................................................................9
Test Run.....................................................................................................................9
Grinding and Buffing.................................................................................................10
Wheel Care...............................................................................................................10
Grinding Wheel Dressing..........................................................................................11
Buffing Wheel Care ..................................................................................................11
Wheel Selection........................................................................................................12
Wheel Inspection......................................................................................................12
Replacing Wheels.....................................................................................................13
SECTION 5: ACCESSORIES.........................................................................................15
SECTION 5: MAINTENANCE ........................................................................................16
General.....................................................................................................................16
Lubrication ................................................................................................................16
Grinding Wheels .......................................................................................................16
Buffing Wheels .........................................................................................................16
SECTION 6: SERVICE...................................................................................................17
Troubleshooting........................................................................................................17
Parts Breakdown ......................................................................................................18
Parts List...................................................................................................................19
WARRANTY AND RETURNS........................................................................................20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazard-
ous conditions. This manual uses a series of symbols and signal words which
are intended to convey the level of importance of the safety messages. The
progression of symbols is described below. Remember that safety messages by
themselves do not eliminate danger and are not a substitute for proper accident
prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
This symbol is used to alert the user to useful infor-
NOTICE
mation about proper operation of the equipment.
Safety Instructions for Machinery
4.
ALWAYS
USE
HEARING
1.
2.
READ THROUGH THE ENTIRE
MANUAL BEFORE STARTING
MACHINERY. Machinery presents
serious injury hazards to untrained
users.
PROTECTIONWHENOPERATING
MACHINERY. Machinery noise can
cause permanent hearing damage.
5.
WEAR PROPER APPAREL. DO
NOT wear loose clothing, gloves,
neckties, rings, or jewelry which
may get caught in moving parts.
Wear protective hair covering to
contain long hair and wear non-slip
footwear.
ALWAYS USE ANSI APPROVED
SAFETY GLASSES
WHEN
OPERATING MACHINERY.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
6.
NEVER OPERATE MACHINERY
WHEN TIRED, OR UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL. Be mentally alert at all
times when running machinery.
3.
ALWAYS WEAR AN ANSI
APPROVED RESPIRATOR WHEN
OPERATING MACHINERY THAT
PRODUCES DUST. Wood dust is
a carcinogen and can cause cancer
and severe respiratory illnesses.
-2-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
ONLY ALLOW TRAINED AND
PROPERLY SUPERVISED PER-
SONNEL TO OPERATE MACHIN-
ERY. Make sure operation instruc-
tions are safe and clearly under-
stood.
16. MAKE SURE GUARDS ARE IN
PLACE AND WORK CORRECTLY
BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS
AND WRENCHES. Make a habit
of checking for keys and adjusting
wrenches before turning machinery
ON.
8.
9.
KEEP CHILDREN AND VISITORS
AWAY. Keep all children and visi-
tors a safe distance from the work
area.
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY.
Check for binding and alignment
of parts, broken parts, part mount-
ing, loose bolts, and any other
conditions that may affect machine
operation. Repair or replace dam-
aged parts.
MAKE
WORKSHOP
CHILD
PROOF. Use padlocks, master
switches, and remove switch keys.
10. NEVER LEAVE WHEN MACHINE
IS RUNNING. Turn power OFF
and allow all moving parts to come
to a complete stop before leaving
machine unattended.
19. DO NOT FORCE MACHINERY.
Work at the speed for which
the machine or accessory was
designed.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use
machinery in damp, wet locations,
or where any flammable or noxious
fumes may exist.
20. SECURE WORKPIECE. Use
clamps or
a
vise to hold the
workpiece when practical.
A
secured workpiece protects your
hands and frees both hands to
operate the machine.
12. KEEP WORK AREA CLEAN AND
WELL LIT. Clutter and dark shad-
ows may cause accidents.
21. DO NOT OVERREACH. Keep
proper footing and balance at all
times.
13. USE A GROUNDED EXTENSION
CORD RATEDFORTHEMACHINE
AMPERAGE. Undersized cords
overheat and lose power. Replace
extension cords if they become
damaged. DO NOT use extension
cords for 220V machinery.
22. MANY MACHINES WILL EJECT
THE WORKPIECE TOWARD THE
OPERATOR. Know and avoid con-
ditions that cause the workpiece to
"kickback."
14. ALWAYS DISCONNECT FROM
POWER
SOURCE
BEFORE
23. ALWAYS LOCK MOBILE BASES
(IF USED) BEFORE OPERATING
MACHINERY.
SERVICING MACHINERY. Make
sure switch is in OFF position before
reconnecting.
24. BE AWARE THAT CERTAIN
DUST MAY BE HAZARDOUS to
the respiratory systems of people
and animals, especially fine dust.
Make sure you know the hazards
associated with the type of dust you
will be exposed to and always wear
a respirator approved for that type
of dust.
15. MAINTAIN MACHINERY WITH
CARE. Keep blades sharp and
clean for best and safest perfor-
mance. Follow instructions for lubri-
cating and changing accessories.
Model H7757 3" Mini Wool Buffer
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions for the 3" Mini Wool Buffer
1.
EYE PROTECTION. Grinding
causes small particles to become
airborne at a high rate of speed.
ALWAYS wear safety glasses
when using this machine.
8.
SIDE GRINDING. Grinding on the
side of wheels can cause them to
break and fly apart—unless the
wheel is rated for side grinding.
9.
TOP GRINDING. Grinding on the
top of wheels greatly increases the
risk of workpiece kickback. Always
grind on the downward part of the
wheel.
2.
MOUNTING TO BENCH/STAND.
An unsecured grinder may become
dangerously out of control during
operation. Make sure grinder is
FIRMLY secured to a bench/stand
before use.
10. HAND TO WHEEL CONTACT.
Grinding wheels can remove a lot
of skin quickly. Keep a firm grip on
the workpiece and position your
hands a safe distance away when
grinding. Avoid wearing gloves as
they may get caught in the grinding
wheel and cause serious entangle-
ment injuries.
3.
WHEEL
SPEED
RATING.
Grinding wheels operated at a
faster speed than rated for may
break or fly apart. Before mounting
a new wheel, be sure the wheel
RPM rating is equal or higher than
the speed of the buffer.
4.
6.
WHEEL FLANGES. Only use the
flanges included with the buffer
when mounting wheels. Other
flanges may not properly secure
the wheel and cause an accident.
11. TOOL REST POSITION. If the tool
rest is too far away from the wheel,
the workpiece may be pulled down,
causing loss of control and pulling
your hand into the grinding wheel.
1
Keep the tool rest within ⁄8" from
the wheel when operating.
STARTING BUFFER. If a grinding
wheel is damaged, it will usually
fly apart shortly after start-up. To
protect yourself, always stand to
the side of the buffer when turning
it ON and allow it to gain full speed
before standing in front of it.
12. CRACKED WHEEL. Cracked
wheels may break and fly apart
during operation. Replace cracked
wheels immediately!
7.
LUNG PROTECTION. Grinding
produces hazardous dust, which
may cause long-term respiratory
problems if breathed. Always wear
a NIOSH approved dust mask or
respirator when grinding.
-4-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: INTRODUCTION
Foreword
Contact Information
We are proud to offer the Grizzly Model
H7757 3" Mini Wool Buffer. This Model
is part of a growing Grizzly family of fine
power tools. When used according to the
guidelines set forth in this manual, you
can expect years of trouble-free, enjoyable
operation and proof of Grizzly’s commit-
ment to customer satisfaction.
If you have any comments regarding this
manual, please write to us at the following
address:
Grizzly Industrial, Inc.
C/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
It is our pleasure to provide this manual
with the Model H7757. It was written
to encourage safety considerations and
guide you through general operating pro-
cedures and maintenance.
Most importantly, we stand behind our
tools. If you have any service questions or
parts requests, please call or write us at
the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
The specifications, details, and photo-
graphs in this manual represent the Model
H7757 as supplied when the manual was
prepared. However, owing to Grizzly’s pol-
icy of continuous improvement, changes
may be made at any time with no obliga-
tion on the part of Grizzly.
E-Mail: [email protected]
Read the manual before operation.
Become familiar with this machine, its
safety instructions, and its operation
before beginning any work. Serious
personal injury may result if safety or
operational information is not under-
stood or followed.
Model H7757 3" Mini Wool Buffer
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: SET UP
Unpacking
Inventory
Your mini wool buffer left our warehouse in
a carefully packed box. If you discover the
mini wool buffer is damaged after you have
signed for delivery, please immediately call
Customer Service at (570) 546-9663 for
advice.
After you have unpacked the carton you
should find the following.
Model H7757 Inventory (Figure 1)
A. Buffer ................................................. 1
B. Eye Shield Brackets........................... 2
C. Tool Rests.......................................... 2
D. Eye Shields........................................ 2
Save the containers and all packing materi-
als for possible inspection by the carrier or
its agent. Otherwise, filing a freight claim
can be difficult.
Tools and Hardware
Phillips Head Screws M5-.8 x 12 ............. 4
Wing Bolts M4-.7 x 10.............................. 2
Phillips Head Screws M4-.7 x 40 ............. 1
Flat Washers 4mm ................................... 2
Flat Washers 5mm ................................... 4
Hex Nuts M5-.8 ........................................ 4
Hex Nuts M4-.7 ........................................ 2
Lock Washers 5mm.................................. 4
Lock Washers 4mm.................................. 2
Wrench 7mm x 10mm.............................. 1
Wrench 8mm x 10mm.............................. 1
When you are completely satisfied with
the condition of the shipment, you should
inventory the equipment.
A
D
B
C
Figure 1. Model H7757 inventory
-6-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Adjust both tool rests approximately 1⁄8
"
Items Needed
for Set Up
from the grinding and buffing wheels
and tighten the wing bolts. Figure 2
shows the correct adjustment for the
tool rest at the grinding wheel.
The following items are needed to com-
plete the set up process, but are not
included with your machine:
1⁄16" Gap
Description
Safety Glasses (for each person)............. 1
Phillips Head Screwdriver ........................ 1
Qty
Wing Bolt
Tool Rest
Optional Items for Mounting
Flat Washer
Drill with 4mm bit...................................... 1
Wrench 4mm............................................ 1
Hex Bolts M4x.7 (length varies) ............... 3
Hex Nuts M4-.7 ........................................ 3
Flat Washers 4mm ................................... 3
Lock Washers 4mm.................................. 3
Figure 2. Tool Rest Installation.
Eye Shields
The eye shield must be positioned between
the grinding or buffing wheel and the
operator’s face to protect the operator from
flying debris. The eye shields are not a
replacement for safety glasses!
Tool Rests
The tool rests attach to the inward side of
the guard and must be used to support
the workpiece during operation. Failure to
install and use the tool rests can lead to
serious personal injury!
Components/Hardware Required Qty
Eye Shields .............................................. 2
Eye Shield Brackets ................................. 2
Phillips Head Screws M4-.7 x 40 ............. 2
Hex Nuts M4-.7 ........................................ 2
Flat Washers 4mm ................................... 2
Phillips Head Screws M5-.8 x 12 ............. 4
Flat Washers 5mm ................................... 4
Hex Nuts M5-.8 ........................................ 4
Lock Washers 5mm.................................. 4
Lock Washers 4mm.................................. 2
Components/Hardware Required Qty
Tool Rests ................................................ 2
Wing Bolts M3-.5 x 10.............................. 2
Flat Washers 4mm ................................... 2
To install the tool rests:
1. Loosely attach the tool rests perpen-
dicular to the surface of each wheel
with the wing bolts and 4mm washers.
To install the eye shields:
1. Attach the eye shield brackets to the
buffer with the 5mm Phillips head
screws, flat washers, lock washers and
hex nuts, as shown in Figure 3.
Model H7757 3" Mini Wool Buffer
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
To secure the buffer to a benchtop or
mounting board:
Screw
1. Place the buffer on a workbench or
mounting board no smaller than 12"W
x 10"D.
Flat Washer
Hex Nut
2. Using the 4mm holes in the buffer base
as a template, drill holes through the
mounting board or benchtop as appro-
priate.
Lock Washer
Figure 3. Eye Shield Bracket Installation.
2. Attach the eye shield to the bracket
with the 4mm Phillips head screws, flat
washers, lock washers and hex nuts as
shown in Figure 4. The hex nut should
be tightened to a point where the eye
shields are stiff to move.
3. Secure the buffer to the benchtop or
mounting board with 4mm hex bolts,
washers, lock washers, and hex nuts
as shown in Figures 5 & 6.
Screw
Hex Nut
Flat Washer
Figure 5. Mounting the buffer (front).
Figure 4. Eye Shield Installation.
Mounting
The buffer must be mounted to a benchtop
or mounting board before it can be used.
An unmounted buffer can become unbal-
anced when in use, potentially causing
serious injury.
Figure 6. Mounting the buffer (back).
Components/Hardware Required Qty
Hex Bolts M4-.7 (length varies)................ 3
Hex Nuts M4-.7 ........................................ 3
Flat Washers 4mm ................................... 3
Lock Washers 4mm.................................. 3
-8-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATIONS
Test Run
Using this machine produces dust
which may cause eye injuries or
respiratory problems. Protect your-
self by wearing safety glasses and a
respirator during the entire operation
process.
To test run the buffer:
1. Plug the machine into the power
source.
2. Stand to the side of the buffer and turn
the machine ON.
The machine should run smoothly with
little or no vibration or rubbing noises.
Strange or unusual noises should be inves-
tigated and corrected before operating the
machine further. If the machine seems
okay, stay out of the line of rotation of
either wheel and let it run for approximate-
ly one minute to make sure the wheels are
structurally sound and safe to use.
Keep loose clothing
rolled up and out of
the way of machin-
ery and keep hair
pulled back.
If you cannot easily locate the source of
an unusual noise or vibration, contact our
Technical Support department for help.
Disconnect
power
from the machine
when performing any
maintenance, assem-
bly or adjustments.
Failure to do this may
result in serious per-
sonal injury.
All grinding wheels, regardless of
size, have the potential of breaking
apart during operation, causing seri-
ous personal injury or death! Always
stand to the side of the grinder when
turning it ON and wear the proper
safety equipment to protect yourself.
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
-9-
Grinding and Buffing
Wheel Care
The processes for grinding and buffing
with the H7757 are very similar.
Your safety largely depends on the con-
dition of the wheels during grinding or
buffing. A grinding wheel in poor condition
presents the possibility of breaking apart
during rotation and injuring the operator,
while a buffing wheel in poor condition
can tear apart and snag a workpiece,
potentially causing serious entanglement
injuries.
To grind or buff:
1. Ensure all eye shields are in place and
that you are wearing the appropriate
safety gear.
2. With the machine plugged into power,
stand to the side of the machine, and
turn it ON.
To properly care for your wheel, follow
these tips:
•
Always transport, store and handle
wheels with care. Grinding wheels
may be damaged if they are dropped
or if heavy objects are stacked on
them.
3. Allow the machine to run for at least
one full minute to ensure that the
wheels are safe for use, then move to
the front of the machine.
4. Grasp the workpiece tightly and prop-
erly support it on the appropriate tool
rest.
•
•
Select the right wheel for the job. DO
NOT grind or buff material that is not
designed for the wheel.
5. Place the workpiece against the front
surface of the wheel with moderate
pressure, moving it back and forth in a
steady, even motion.
Select the right wheel for the machine.
A machine that rotates at a higher
RPM than the wheel rating may cause
the wheel to break or tear apart.
Note: Using too much pressure will
slow the motor and may damage the
wheel. Using too little pressure will
make the workpiece bounce around
and you will not make good contact
with the wheel.
•
Mount the wheels properly. (See the
Replacing Wheels instructions on
Page 13 for guidance.) Never use a
wheel with the wrong arbor size for the
buffer.
•
•
DO NOT abuse a wheel by jamming
the workpiece into the wheel with
excessive force.
6. After turning the buffer OFF, DO NOT
continue grinding or buffing and
DO NOT manually stop either wheel
with your workpiece!
Learn how to use the buffer and the
grinding and buffing wheels properly.
Ask a trusted person with experience
or consult with your local library to
learn more.
-10-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
Grinding Wheel
Dressing
Buffing Wheel Care
Dressing restores the grinding wheel with
a like-new abrasive quality. Whenever the
front surface of the wheel loses its abra-
sive qualities or balance due to particle
loading or polishing of the wheel surface,
then the wheel should be dressed. Use a
commercially-available dressing tool, such
as those available on Page 15.
The process of cleaning buffing
wheels produces airborne dust and
particles may cause eye injuries or
respiratory problems. Protect your-
self by wearing safety glasses and a
respirator during the entire cleaning
process.
Buffing wheels can sometimes become
caked or clogged with buffing compound,
reducing their effectiveness. In order to
clean a buffing wheel, use a commercially-
available buffing rake, such as those avail-
able on Page 15.
To dress the grinding wheel:
1. With the machine plugged into power,
stand to the side of the grinding wheel
turn the machine ON.
2. Allow the machine to run for at least
one full minute to make sure that the
grinding wheel is safe to use, then
move to the front of the machine.
To clean the buffing wheel:
1. With the machine plugged into power,
stand to the side of the grinding wheel
and turn the machine ON.
3. Hold the dressing tool firmly on the tool
rest with both hands and press it lightly
against the front surface of the grind-
ing wheel.
2. Hold the buffing rake firmly on the tool
rest with both hands and press it lightly
against the front surface of the buffing
wheel.
4. Move the dressing tool in a side-to-
side motion, while keeping it even with
the surface of the grinding wheel.
3. Move the buffing rake in a side-to-side
motion, while keeping it even with the
surface of the buffing wheel. As the
buffing wheel is cleaned, old com-
pound will be removed and fresh fibers
exposed.
5. Regularly pull the dressing tool away
from the wheel for visual inspection
and repeat Steps 3 & 4 until the
surface of the wheel appears to be
restored to its normal color and bal-
ance.
4. Regularly pull the buffing rake away
from the wheel for visual inspection
and repeat Steps 3 & 4 until the sur-
face of the wheel appears to cleaned
of compound and restored to its origi-
nal condition and color.
Model H7757 3" Mini Wool Buffer
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Bond Type refers to the type of bonding
material used to hold the abrasive material.
Most general purpose wheels will have a
“V” indicating Vitrified Clay is used. Vitrified
Clay provides high strength and good
porosity. The other common bond type is
“B” for resin where synthetic resins are
used. These are used to grind cemented
carbide and ceramic materials.
Wheel Selection
The Model H7757 only accepts Type 1 3"
x 1⁄2" wheels with a 1⁄4" bore.
Aluminum oxide and silicon carbide wheels
are marked in a somewhat uniform manner
by all major manufacturers. Understanding
these markings will help you understand
the capabilities of various wheels. Always
refer to the manufacturer’s grinding recom-
mendations when selecting a wheel for
your project.
There may be other numbers inserted that
have meaning for a particular type of wheel.
Refer to the wheel manufacturer’s technical
data for a complete explanation.
Wheel Inspection
The basic format for wheel numbering
is:
Abrasive Grit Grade Bond
Prefix
Type
Size Type Type
The hazards of using a damaged
grinding wheel include flying chunks
of sharp abrasive material that could
cause serious injury or death. Inspect
every grinding wheel before it is
mounted and DO NOT use a damaged
grinding wheel!
Type 1
A
60
L
V
The Prefix is the manufacturer’s designa-
tion for a particular standardized type
of grinding wheel. Different Type pre-
fixes indicate different wheel shapes and
designs. For more information on wheel
types, ask a person with grinding experi-
ence or consult your local library.
Before mounting a new grinding wheel, it
must be inspected. DO NOT assume that
a wheel is in sound condition just because
it is new—often, damage can occur during
shipping, with age, or with exposure to
moisture.
The most common Abrasive Types used
are A for Aluminum Oxide and C for Silicon
Carbide, and occasionally SG for Seeded
Gel.
First, the wheel should be given a Visual
Inspection. Look for any cracks, chips,
nicks, or dents in the surface of the wheel.
If you see any of these, DO NOT use the
wheel.
The Grit Size is a number that refers to
the size of the abrasive grain in the wheel.
The lower the number, the coarser the
wheel. Grit sizes range from 10, which is a
very coarse grit used for roughing, to 220,
which is usually the upper range for fine
finish work.
Second, the wheel should be given a Ring
Test. This test will give you an indication of
any internal damage that may not be obvi-
ous during a visual inspection.
Grade Type is an indication of the hard-
ness of the wheel—“A” being the softest
and “Z” being the hardest.
-12-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
To perform a Ring Test:
To remove/mount a wheel:
1.
2.
3.
Make sure the wheel that you test is
clean and dry; otherwise, you may
get false results.
1. DISCONNECT THE MACHINE FROM
THE POWER SUPPLY!
2. Remove the three Phillips head screws
and tooth washers that go through the
outer guard, and take off the outer
guard.
Hang the wheel in the air with a piece
of cord or string looped through the
hole in the center.
At the spots shown in Figure 7,
gently tap the wheel with a light non-
metallic device such as the handle of
a screwdriver or a wooden mallet.
3. Use a wrench on the nut that holds
the wheel on the arbor. Hold the wheel
from turning with your other hand.
Note: The left end of the arbor has a
left-handed thread, so loosening the
nut will require turning it clockwise.
4. Remove the outer wheel flange and
paper disc. Pull the wheel free from
the arbor. There will also be a paper
disc and a wheel flange on the back
side of the wheel which should also be
removed.
5. Mount the new wheel in the reverse
order that you removed it or as shown
in Figure 8. Always make certain there
are paper or fiber discs between the
wheel flanges and the wheel itself.
Tighten the nut snugly but DO NOT
over-tighten. Over-tightening can crack
a grinding wheel.
Figure 7. Ring test tapping locations.
4.
5.
An undamaged wheel will emit a
clear metallic ring or “ping” sound
in each of these spots. A damaged
wheel will respond with a dull thud
that has no clear tone.
If you determine from the ring test
that the wheel is damaged, DO NOT
use it!
Paper/Fiber Disc
Replacing Wheels
Flange
Flange
Wheel
The wheel guard assembly must be
removed in order to mount or dismount a
buffing or grinding wheel.
Paper/Fiber Disc
Hex Nut
Figure 8. Wheel mounting order.
Model H7757 3" Mini Wool Buffer
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
NEVER assemble a grinding wheel on
the arbor without paper or fiber discs
between the wheel and the flanges.
Failure to include the paper or fiber
discs can result in damage to the
wheel and cause it to fail when at
speed, causing serious injury!
6. Re-install the guards and shields.
7. Run a new wheel for at least one min-
ute while standing clear of the line of
rotation. If a wheel does have defects
it will generally fail as soon as it gets
up to full speed.
-14-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ACCESSORIES
H5944—#0 Wheel Dresser
G7984—Face Shield
H5945—#1 Wheel Dresser
H5946—#2 Wheel Dresser
H1298—Dust Sealed Safety Glasses
H1300—Clear Safety Glasses
H2347—Uvex® Spitfire Safety Glasses
H0736—Shop Fox® Safety Glasses
Safety Glasses are essential to every
shop. If you already have a pair, buy
extras for visitors or employees. You can't
be too careful when it comes to shop
safety!
These wheel dressers expose new grains
for aggressive cutting on all types of grind-
ing wheels. The star wheels and discs are
hardened steel, and the cast iron handle
provides stabilizing mass for better control.
Available in three sizes: #0, #1 and #2.
H5946
H1300
H1298
G7984
H5944
H5945
H2347
H0736
Figure 10. Our range of Wheel Dressers.
Figure 9. Our most popular safety
H4383—Buffing Rake
H4384—Replacement Rake
glasses.
Great for removing dried compound from
buffing wheels. Simply guide the rake
across the buffing surface to clean the
wheel and expose fresh fibers.
Figure 11. Our Buffing Rake in action.
Model H7757 3" Mini Wool Buffer
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: MAINTENANCE
General
Grinding Wheels
Always be aware of the condition of your
machine. Routinely check the condition of
the following items and repair or replace
as necessary:
The grinding wheel should be visually
inspected before every use. Take care
when storing grinding wheels to keep them
free from potential damage due to being
dropped or having other items dropped
on them. Store all grinding wheels in a dry
location. Type 1 grinding wheels should
be stored vertically with cushioning mate-
rial between each wheel.
•
•
•
•
•
•
Damaged or loose grinding wheels.
Loose mounting bolts or arbor nuts.
Worn switch.
If a grinding wheel diameter has been
reduced to 21⁄2", the wheel must be
replaced. Operating a wheel at anything
less than this diameter can lead to wheel
explosion and serious personal injury.
Worn or damaged cord.
Worn or damaged support bearings.
Any other condition that could hamper
the safe operation of this machine.
Grinding wheels will require periodic
dressing. Refer to the Wheel Dressing
instructions on Page 13 for details on how
this is done.
Lubrication
Buffing Wheels
Sealed and pre-lubricated ball bearings
require no additional attention for the life
of the bearings. All bearings are standard
sizes, and replacements can be pur-
chased from our Parts Department or a
bearing supply store.
Buffing wheels should be regularly
cleaned of compounds to maintain their
effectiveness and surface texture. Wool
buffing wheels will shed fibers and will
need to be replaced eventually. If a buff-
ing wheel is reduced to 21⁄2", the wheel
must be replaced. Operating a wheel at
anything less than this diameter can tear
or rip, posing an entangement hazard for
the workpiece and operator.
-16-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: SERVICE
Troubleshooting
Symptom
Machine slows 1. Workpiece pressure is too 1. Reduce workpiece pressure on
when operating. great. wheel.
Machine vibrates 1. Grinding wheel is unbal- 1. Adjust or tighten wheel mounting
when operating. anced. nut as necessary.
2. Grinding wheel is damaged. 2. Replace the wheel.
3. Arbor is bent. 3. Inspect arbor and replace if nec-
essary.
4. Bearings are worn or dam- 4. Inspect bearings and replace if
aged. necessary.
Wavy condition 1. Workpiece not being held 1. Use a holding device to firmly
Possible Cause
Possible Solution
on surface of
workpiece.
firmly.
2. Wheel face uneven.
3. Wheel is too hard.
retain the workpiece.
2. Dress the grinding wheel.
3. Use softer wheel.
Lines on surface 1. Impurity on wheel surface.
of workpiece.
1. Dress the grinding wheel.
2. Workpiece not being held 2. Use a holding device to firmly
tightly. retain the workpiece.
Burning spots 1. Workpiece pressure is too 1. Reduce workpiece pressure on
or cracks in the
workpiece.
great.
wheel.
2. Improper grinding wheel 2. Try a wheel that is of a softer style
type.
or coarser grit.
3. Coolant required.
3. Cool the workpiece frequently.
Wheel
dulls 1. Workpiece pressure is too 1. Reduce workpiece pressure on
quickly, grit falls
off.
great.
2. Wheel is too soft.
wheel.
2. Select a wheel with a harder
bond.
3. Wheel diameter too small.
4. Bad wheel dress.
5. Defective wheel bonding.
3. Replace the wheel.
4. Dress the wheel.
5. Consult manufacturer of grinding
wheel.
Wheel clogs and 1. Wheel is too hard.
workpiece shows 2. Feed rate too slow.
burn marks.
1. Select a softer wheel bond.
2. Increase rate of movement of
workpiece onto wheel.
3. Bad wheel dress.
3. Dress the wheel.
4. Coolant required.
4. Cool the workpiece frequently.
Poor buffing per- 1. Buffing wheel is loaded with 1. Clean wheel with a buffing rake as
formance. compound residue. on Page 11.
2. Buffing wheel is worn down. 2. Replace buffing wheel.
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
-17-
Parts Breakdown
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
��
��
��
��
��
��
��
��
��
��
��
�
�
�
�
�
�
�
�
-18-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
REF
PART #
DESCRIPTION
1
PS49M
PHLP HD SCR M3-.5 X 5
BASE PLATE
2
PH7757002
PH7757003
PH7757004
PH7757005
PH7757006
PH7757007
PH7757008
PS02M
3
RUBBER FOOT
4
BASE
5
MOVEABLE TOOL REST
WING BOLT M4-.7 X 10
ROCKER SWITCH
6
7
8
SWITCH COVER
9
PHLP HD SCR M4-.7 X 12
CAPACITOR 3MFD 250VAC
PHLP HD SCR M4-.7 X 15
HEX NUT M4-.7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
PH7757010
PS21M
PN04M
PH7757013
PH7757014
PW05M
CORD & PLUG
PHLP HD SCR M4-.7 X 86
FLAT WASHER 4MM
FLAT WASHER 4MM
LEFT SAFE GUARD PLATE
PHLP HD SCR M5-.8 X 12
FLAT WASHER 5MM
EYE SHIELD BRACKET
HEX NUT M5-.8
PW05M
PH7757017
PS08M
PW02M
PH7757020
PN06M
PLW01M
LOCK WASHER 5MM
ARBOR BUSHING
PH7757023
PH7757024
PH7757025
PH7757026
PS49M
LEFT END CAP
SPECIAL WAVE WASHER 19MM
BEARING 626Z
PHLP HD SCR M3-.5 X 5
EXT TOOTH WASHER 3MM
STATOR
PTLW13M
PH7757029
PH7757030
PH7757031
PH7757032
PLW02M
ROTOR
RIGHT END CAP
RIGHT SAFE GUARD PLATE
LOCK WASHER 4MM
SEAL RING
PH7757034
PH7757035
PN37M
LEFT SAFE GUARD COVER
HEX NUT M5-.8 LH
FLANGE
PH7757037
PH7757038
H8871
SHAFT SLEEVE
BUFFING WHEEL 3" X 3/4"
GRINDING WHEEL 3" X 1/2"
HEX NUT M5-.8
H8870
PN06M
PH7757042
PH7757043
PS38M
RIGHT SAFE GUARD COVER
CORD BUSHING
PHLP HD SCR M4-.7 X 10
PHLP HD SCR M3-.5 X 5
PHLP HD SCR M4-.7 X 40
EYE SHIELD
PS49M
PS65M
PH7757047
PH7757048
PH7757049
PH7757050
PWR810
WRENCH 7 X 10
MACHINE ID LABEL
MACHINE WARNING LABEL
WRENCH 8 X 10
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
-19-
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original
purchaser from the date of purchase. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of
maintenance. This is Grizzly’s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are
hereby limited to the duration of this written warranty. We do not warrant or represent that
the merchandise complies with the provisions of any law or acts unless the manufacturer so
warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price
paid for the product and any legal actions brought against Grizzly shall be tried in the State
of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special, or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details.
We will then issue you a “Return Authorization Number,” which must be clearly posted on
the outside as well as the inside of the carton. We will not accept any item back without this
number. Proof of purchase must accompany the merchandise.
The manufacturers reserve the right to change specifications at any time because they
constantly strive to achieve better quality equipment. We make every effort to ensure that
our products meet high quality and durability standards and we hope you never need to
use this warranty.
Please feel free to write or call us if you have any questions about the machine or the
manual.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail:
Thank you again for your business and continued support. We hope to serve you again
soon!
-20-
Model H7757 3" Mini Wool Buffer
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Name_________________________________________________________________
Street_________________________________________________________________
City _______________________ State_________________________ Zip _________
Phone #____________________ Email ________________________ Invoice #_____
Model # ____________________ Order #_______________________ Serial #______
The following information is given on a voluntary basis. It will be used for marketing purposes to
help us develop better products and services. All information is strictly confidential.
1. How did you learn about us?
____Advertisement
____Friend
____Catalog
____Card Deck
____Website
Other:________________________
2. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist ____ Precision Shooter
____ Journal of Light Cont. ____ Projects in Metal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking ____ Wooden Boat
____ Practical Homeowner ____ Woodshop News
____ Today’s Homeowner
____ Wood
____ Woodsmith
____ Woodwork
____ Live Steam
____ Model Airplane News ____ Rifle
____ Modeltec
____ Old House Journal
____ RC Modeler
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Shop Notes
____ Shotgun News
3. What is your annual household income?
____$20,000-$29,000
____$30,000-$39,000
____$40,000-$49,000
____$70,000+
____$50,000-$59,000
____$60,000-$69,000
4. What is your age group?
____20-29
____30-39
____60-69
____40-49
____70+
____50-59
5. How long have you been a woodworker/metalworker?
____0-2 Years ____2-8 Years ____8-20 Years
____20+ Years
6. How many of your machines or tools are Grizzly?
____0-2 ____3-5 ____6-9
____10+
____No
____No
7. Do you think your machine represents a good value? ____Yes
8. Would you recommend Grizzly Industrial to a friend? ____Yes
9. Would you allow us to use your name as a reference for our customers in your area?
Note: We never use names more than 3 times. ____Yes ____No
10. Comments:_________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
Send a Grizzly Catalog to a friend:
Name________________________________
Street________________________________
City______________State______Zip_______
FOLD ALONG DOTTED LINE
Place
Stamp
Here
GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
|