Instructions–Parts List
19 LITER (5 GALLON)
308049U
ENG
Wiper Plates
For straight-sided or tapered pails. Fit Check-Matet Pumps on a
Pneumatic Elevator Cart or Ram. For professional use only.
Not approved to European explosive atmosphere requirements.
U.S. Patent No. 5,117,998
Important Safety Instructions
Read all warnings and instructions in this manual.
Save these instructions.
See page 2 for Table of Contents and List of
Models.
Model 222812
0212A
Model 222909
01115
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols
Warning Symbol
Caution Symbol
WARNING
CAUTION
This symbol alerts you to the possibility of serious
injury or death if you do not follow the instructions.
This symbol alerts you to the possibility of damage to
or destruction of equipment if you do not follow the
instructions.
WARNING
EQUIPMENT MISUSE HAZARD
Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury.
D This equipment is for professional use only.
INSTRUCTIONS
D Read all instruction manuals, tags, and labels before operating the equipment.
D Use the equipment only for its intended purpose. If you are uncertain about usage, call your Graco
distributor.
D Do not alter or modify this equipment. Use only genuine Graco parts and accessories.
D Check equipment daily. Repair or replace worn or damaged parts immediately.
D Use fluids and solvents which are compatible with the equipment wetted parts. Refer to the Tech-
nical Data section of all equipment manuals. Read the fluid and solvent manufacturer’s warnings.
D Comply with all applicable local, state, and national fire, electrical, and safety regulations.
MOVING PARTS HAZARD
Moving parts, such as the priming piston and wiper plate, can pinch or amputate your fingers.
D Keep clear of all moving parts when starting or operating the pump.
D Keep hands and fingers away from the priming piston during operation and whenever the pump is
charged with air.
D Keep your hands away from the wiper plate and the lip of the pail while the ram is operating.
D Before servicing the equipment, follow the Pressure Relief Procedure on page 5 to prevent the
equipment from starting unexpectedly.
308049
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
4
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation (All Wiper Plates)
3. Shut off the main air bleed valve (required in your
Pressure Relief Procedure
system).
WARNING
4. Unlock the gun/valve trigger safety.
SKIN INJECTION HAZARD
The system pressure must be manually
relieved to prevent the system from
5. Hold a metal part of the gun/valve firmly to the side
of a grounded metal pail, and trigger the gun/valve
to relieve pressure.
starting or spraying accidentally. Fluid
under high pressure can be injected through the
skin and cause serious injury. To reduce the risk of
an injury from injection, splashing fluid, or moving
parts, follow the Pressure Relief Procedure
whenever you:
6. Lock the gun/valve trigger safety.
7. Open the drain valve (required in your system)
and/or the pump bleeder valve, having a container
ready to catch the drainage.
D are instructed to relieve the pressure,
D stop spraying/dispensing,
D check or service any of the system equipment,
D or install or clean the spray tip/nozzle.
8. Leave the drain valve open until you are ready to
spray again.
If you suspect that the spray tip/nozzle or hose is
completely clogged, or that pressure has not been fully
relieved after following the steps above, very slowly
loosen the tip guard retaining nut or hose end coupling
and relieve pressure gradually, then loosen completely.
Now clear the tip/nozzle or hose.
1. Lock the gun/valve trigger safety.
2. Close the pump air bleed valve (required in your
system).
308049
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on a Ram
(Carbon Steel or Aluminum Plates)
b. To reinstall the spacer for use with a
Installation
straight sided pail, first make sure the large
diameter of the spacer (19) is facing down.
Work the spacer up over the wiper plate by
hand, so it is completely above the flange (D)
of the wiper plate. See Fig. 3. Then, working
from the top, use a screwdriver to position the
spacer between the flange (D) and the wipers
(E). See Fig. 4.
Reference letters and numbers in the text refer to Figs.
1–4 and the Parts Drawings on pages 14–15.
WARNING
MOVING PARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the priming
piston and the lip of the pail.
4. Connect a 610 mm (24 in.), 1/4 in. (6.3 mm) OD
nylon tube (F) with a 1/8 npt(f) fitting (H) from the
ram’s air assist tube fitting (G) to the air assist
check valve (21) on the wiper plate.
WARNING
To reduce the risk of serious injury, whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
5. Refer to the separate ram and pump manuals for
set-up and operating instructions.
Maintenance
1. Relieve the pressure.
2. Install the wiper plate (A) onto the pump intake (B),
with the wiper plate vent handle (C) facing the front
of the ram. Secure by tightening the setscrew (3).
See Fig. 1.
If the wiper plate does not come out of the pail easily
when the pump is being raised, the air assist tube (F),
fitting (H), and check valve (21) may be plugged. This
prevents air from reaching the underside of the plate to
assist in raising it from the pail.
3. The wiper plate is supplied for use with 19 liter (5
gallon) straight sided pails, but it can be easily
modified for use with tapered pails. See steps a
and b.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
a. To use the wiper plate with tapered pails,
the large spacer (19) must be removed. Work-
ing from the bottom, use a screwdriver to pry
the spacer loose. Work it upward so it is com-
pletely above the flange (D) of the wiper plate.
See Fig. 2. Next, by hand, angle the spacer
and work it off the plate, pulling it down over
the flange and bottom wipers (E). See Fig. 3.
Save the spacer, as it is required for other
applications.
Relieve the pressure. Refer to the Parts Drawings on
pages 14–15 and disassemble the air assist check
valve as shown. Clear the tube (F) and the port in the
wiper plate. Clean all parts of the check valve assem-
bly, and reassemble.
6
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on a Ram
(Carbon Steel and Aluminum Plates)
Installing the Wiper Plate on a Ram
(Model 222812 shown; large diameter of
spacer facing down)
To use Model 222812 and 235516, Plates with tapered
pails, the spacer (19) must be removed. See page 6,
1
and Figs. 2–4.
D
19
E
0248A
Fig. 2
G
F
D
19
E
0249A
C
B
H
Fig. 3
A
3
19
1
19
06540A
Fig. 1
E
0251A
D
Fig. 4
308049
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on a Cart
(Carbon Steel and Aluminum Plates)
b. To use the wiper plate with tapered pails,
Installation
the large spacer (19) must be removed. Work-
ing from the bottom, use a screwdriver to pry
the spacer loose. Work it upward so it is com-
pletely above the flange (D) of the wiper plate.
See Fig. 6. Next, by hand, angle the spacer
and work it off the plate, pulling it down over
the flange and bottom wipers (E). See Fig. 7.
Save the spacer, as it is required for other
applications.
Reference letters and numbers in the text refer to Figs.
5–8 and the Parts Drawings on pages 14–15.
WARNING
MOVING PARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the priming
piston and the lip of the pail.
4. Install Cart Accessory Kit 224376. See 308087 for
details.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
5. Refer to the separate cart and pump manuals for
set-up and operating instructions.
1. Relieve the pressure.
2. Install the wiper plate (A) onto the pump intake (B),
with the wiper plate vent handle (C) facing the front
of the cart. Secure by tightening the setscrew (3).
See Fig. 5.
Maintenance
If the wiper plate does not come out of the pail easily
when the pump is being raised, the air assist tube (F),
fitting (H), or check valve (21) may be plugged. This
prevents air from reaching the underside of the plate to
assist in raising it from the pail.
3. The wiper plate is supplied for use with 19 liter (5
gallon) straight sided pails on a ram. It must be
modified for use with the pneumatic elevator cart.
See steps a and b, following.
a. To use the wiper plate with straight sided
pails, the large spacer (19) must be inverted.
Working from the bottom, use a screwdriver to
pry the spacer loose. Work it upward so it is
completely above the flange (D) of the wiper
plate. See Fig. 6. Next, by hand, angle the
spacer and work it off the plate, pulling it down
over the flange and bottom wipers (E). See
Fig. 7. Turn the spacer so the large diameter
is facing up. Work the spacer up over the
wiper plate by hand, so it is completely above
the flange (D) of the wiper plate. Working from
the top, use a screwdriver to position the
spacer between the flange (D) and the wipers
(E). See Fig. 8.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
Relieve the pressure. Refer to the Parts Drawings on
pages 14–15 and disassemble the air assist check
valve as shown. Clear the tube (F) and the port in the
wiper plate. Clean all parts of the check valve assem-
bly, and reassemble.
8
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on a Cart
(Carbon Steel and Aluminum Plates)
Installing the Wiper Plate on a
Pneumatic Elevator Cart
(Model 222812 shown;
large diameter of spacer facing up)
To use Model 222812 and 235516 Plates with tapered
pails, the spacer (19) must be removed. See page 8,
1
and Figs. 6–8.
2
Part of Kit 224376 (See 308087).
D
19
E
0248A
Fig. 6
F
2
C
H
D
19
E
0249A
Fig. 7
3
B
19
A
1
19
0252D
Fig. 5
E
D
0251A
Fig. 8
308049
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on aRam
(Stainless Steel Plates)
4. Connect a 965 mm (38 in.), 6.3 mm (1/4 in.) OD
Installation
tube (F) from the ram’s air assist valve (G) to the
elbow (H) on the wiper plate.
Reference letters and numbers in the text refer to Figs.
9–12 and the Parts Drawing on page 16.
5. Refer to the separate ram and pump manuals for
set-up and operating instructions.
WARNING
Operating the Air Assist Valve Handle
MOVING PARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the priming
piston and lip of the pail.
The ram’s air assist valve (G) directs air under the
wiper plate, making it easier to pull the plate out of the
pail. For the air assist valve to function, you must open
a passage for the air with the valve handle (J). Practice
using the handle a few times, until you are familiar with
its use.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
1. Stop the pump. Relieve the pressure.
1. Relieve the pressure.
2. To open a passage for air to get under the plate,
rotate the handle (J) 45_ clockwise and pull it
upward (it should travel about 13 mm [1/2 in.] up
and down).
2. Install the wiper plate (A) onto the pump intake (B),
with the wiper plate vent handle (C) facing the left
of the ram. Secure by tightening the setscrews
(17). See Fig. 9.
3. Turn the ram director valve to UP. Press the air
assist valve (G), and hold it in until the plate clears
the top of the pail.
3. The wiper plate is supplied for use with 19 liter (5
gallon) straight sided pails, but it can be easily
modified for use with tapered pails. See steps a
and b
4. To close the air passage, push the handle (J) down
and rotate it 45_ counterclockwise to lock.
a. To use the wiper plate with tapered pails,
the large spacer (8) must be removed. Work-
ing from the bottom, use a screwdriver to pry
the spacer loose. Work it upward so it is com-
pletely above the flange (D) of the wiper plate.
See Fig. 10. Next, by hand, angle the spacer
and work it off the plate, pulling it down over
the flange and bottom wipers (E). See Fig. 11.
Save the spacer, as it is required for other
applications.
Maintenance
If the wiper plate does not come out of the pail easily
when the pump is being raised, the air assist tube (F),
elbow (H), or valve (J) may be plugged. A plugged
valve prevents air from reaching the underside of the
plate to assist in raising it from the pail.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
b. To reinstall the spacer for use with a
straight sided pail, first make sure the large
diameter of the spacer (8) is facing down.
Work the spacer up over the wiper plate by
hand, so it is completely above the flange (D)
of the wiper plate. See Fig. 11. Then, working
from the top, use a screwdriver to position the
spacer between the flange (D) and the wipers
(E). See Fig. 12.
Relieve the pressure. Refer to the Parts Drawing on
page 16 and disassemble the air assist valve (J) as
shown. Clear the hose (F) and the elbow (H) in the
wiper plate. Clean all parts of the valve, and reas-
semble.
10
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on aRam
(Stainless Steel Plates)
Installing the Wiper Plate on a Ram
(large diameter of spacer facing down)
To use Model 222909 Plate with a tapered pail, the spacer (8)
must be removed. See page 10, and Figs. 10–12.
1
D
8
E
01116
Fig. 10
G
F
F
D
8
J
C
E
H
01117
A
Fig. 11
8
8
1
B
17
06754C
Fig. 9
E
D
01118
Fig. 12
308049
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on aCart
(Stainless Steel Plates)
4. Install Cart Accessory Kit 224376. See 308199 for
Installation
details.
Reference letters and numbers in the text refer to Figs.
13–16 and the Parts Drawing on page 16.
5. Refer to the separate cart and pump manuals for
set-up and operating instructions.
WARNING
Operating the Air Assist Valve Handle
MOVING PARTS HAZARD
Moving parts can pinch or amputate your
fingers. When the pump is operating and
when raising or lowering the ram, keep
your fingers and hands away from the priming
piston and the lip of the fluid container.
The cart’s air assist toggle valve (G) directs air under
the wiper plate, making it easier to pull the plate out of
the pail. Refer to manual 308199 for instructions on
changing pails using the air assist valve.
For the air assist valve to function, you must open a
passage for the air with the valve handle (J). Practice
using the handle a few times, until you are familiar with
its use.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
1. Relieve the pressure.
2. Install the wiper plate (A) onto the pump intake (B),
with the wiper plate vent handle (C) facing the left
of the cart. Secure by tightening the setscrews
(17). See Fig. 13.
1. Relieve the pressure.
3. The wiper plate is supplied for use with 19 liter (5
gallon) straight sided pails on a ram. It must be
modified for use with the pneumatic elevator cart.
See steps a and b following.
2. To open a passage for air to get under the plate,
rotate the handle (J) 45_ clockwise and pull it
upward (it should travel about 13 mm [1/2 in.] up
and down).
a. To use the wiper plate with straight sided
pails, the large spacer (8) must be inverted.
Working from the bottom, use a screwdriver to
pry the spacer loose. Work it upward so it is
completely above the flange (D) of the wiper
plate. See Fig. 14. Next, by hand, angle the
spacer and work it off the plate, pulling it down
over the flange and bottom wipers (E). See
Fig. 15. Turn the spacer so the large diameter
is facing up. Work the spacer up over the
wiper plate by hand, so it is completely above
the flange (D) of the wiper plate. Working from
the top, use a screwdriver to position the
spacer between the flange (D) and the wipers
(E). See Fig. 16.
3. To close the air passage, push the handle (J) down
and rotate it 45_ counterclockwise to lock.
Maintenance
If the wiper plate does not come out of the pail easily
when the pump is being raised, the air assist tube (F),
elbow (H), or valve (J) may be plugged. A plugged
valve prevents air from reaching the underside of the
plate to assist in raising it from the pail.
WARNING
To reduce the risk of serious injury whenever you
are instructed to relieve pressure, always follow the
Pressure Relief Procedure on page 5.
b. To use the wiper plate with tapered pails,
the large spacer (8) must be removed. Work-
ing from the bottom, use a screwdriver to pry
the spacer loose. Work it upward so it is com-
pletely above the flange (D) of the wiper plate.
See Fig. 14. Next, by hand, angle the spacer
and work it off the plate, pulling it down over
the flange and bottom wipers (E). See Fig. 15.
Save the spacer, as it is required for other
applications.
Relieve the pressure. Refer to the Parts Drawing on
page 16 and disassemble the air assist valve (J) as
shown. Clear the hose (F) and the elbow (H) in the
wiper plate. Clean all parts of the valve, and reas-
semble.
12
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation on aCart
(Stainless Steel Plates)
Installing the Wiper Plate on a
Pneumatic Elevator Cart
(large diameter of spacer facing up)
To use Model 222909 Plate with a tapered pail, the spacer (8)
must be removed. See page 12, and Figs. 14–16.
1
2
Part of Kit 224376; see 308199.
G
D
8
E
01116
Fig. 14
F
2
J
H
C
D
8
E
01117
Fig. 15
8
A
1
8
B
17
01096
Fig. 13
E
D
01118
Fig. 16
308049
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
1
2
Model C50260, Series B
Model 222812, Series B
Carbon Steel Wiper Plate
with Buna-N Wiper
13
21
and UHMWPE Backup
4
14
3
16
19
5
12
15
9
0254D
6
0254B
Ref.
No.
Part
No.
Ref.
No.
Part
No.
Description
Qty
Description
Qty
1
1
2
3
101831
177542
100421
PIN, spring, straight
HANDLE
1
1
13
14
109458
102040
O-RING; fluoroelastomer
NUT, hex, self-locking;
with nylon insert; 1/4–20 unc–3b
WIPER; polyethylene
(Model 222812 only)
SETSCREW, socket hd, cup point;
5/16–18 x 3/8 in. (9.5 mm) long
STEM, probe
WIPER; synthetic rubber
SCREW, machine, flat-hd;
zinc-plated carbon steel;
1/4–20 x 1 in. (25 mm) long
CLAMP, retaining
8
2
1
1
15n
184421
184418
4
5n
6
166560
184420
109469
1
16
CLAMP, retaining;
zinc-plated carbon steel
SPACER; polyurethane
VALVE, check, air assist
1
1
1
19
21
276049
114317
8
1
1
9
184419
222764
n Keep these spare parts on hand to reduce down time.
zinc-plated carbon steel
PLATE, wiper;
zinc-plated carbon steel
12
14
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
1
2
13
Model 235516, Series B
Carbon Steel Wiper Plate
with PTFE-coated Wiper
and UHMWPE Backup
21
4
14
3
16
19
12
20
5
15
9
6
01456A
Ref.
No.
Part
No.
Ref.
No.
Part
No.
Description
Qty
Description
Qty
1
2
3
101831
177542
100421
PIN, spring, straight
HANDLE
1
1
13
14
109458
102040
O-RING; fluoroelastomer
NUT, hex, self-locking;
with nylon insert; 1/4–20 unc–3b
WIPER; polyethylene
1
SETSCREW, socket hd, cup point;
5/16–18 x 3/8 in. (9.5 mm) long
STEM, probe
WIPER; nitrile/PTFE
SCREW, machine, flat-hd;
zinc-plated carbon steel;
1/4–20 x 1 in. (25 mm) long
CLAMP, retaining
8
1
1
1
1
15n
16
184421
184418
4
5n
6
166560
184552
109469
CLAMP, retaining;
zinc-plated carbon steel
SPACER; polyurethane
WIPER; polyethylene
1
1
1
1
19
20n
21
276049
184551
114317
8
1
1
VALVE, check, air assist
9
184419
222764
n Keep these spare parts on hand to reduce down time.
zinc-plated carbon steel
PLATE, wiper;
zinc-plated carbon steel
12
308049
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 222909, Series A
Stainless Steel Wiper Plate
with PTFE-coated Wiper
and UHMWPE Backup
Valve Assembly Procedure
(see Detail below)
1. Assemble all wipers and the clamp (9) to the plate
(5) as shown at left, before assembling the valve.
2. Insert the seal (19) in the hole (K) of the collar (1).
Align the hole and the flat of the guide (15) with the
hole (L) in the collar, and install the guide. Screw
the elbow (11) into the hole (L) until snug. Do not
overtighten. The guide (15) should be held from
rotating by the elbow (11) but should not be
clamped firmly in place.
PTFE side faces down, toward fluid.
1
2
Located inside assembly of items 1 and 5.
10
3. Slide the nut (13) and seal (19) onto the stem (14).
Press the pin (12) into the hole in the stem (14)
until the pin bottoms out.
9
4. Insert the stem (14) into the hole (K) so the pin
(12) travels in the slot of the guide (15). Push the
seal (19) down into the hole (K) and tighten the nut
(13) snugly – do not overtighten. (Stem (14)
should not rotate more than 90_).
8
5. Operate the valve a few times to ensure proper
assembly.
20
7
6
1
Assembled Detail of Air Assist Check Valve
14 13
16
14
K
1
2
16
12
19
12
15
13
19
14 (Ref)
L
11
1
17
15
19
19
K
5
4
11
01213
2
3
L
01119
16
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Model 222909, Series A
Stainless Steel Wiper Plate
with PTFE-coated Wiper
and UHMWPE Backup
Ref.
No.
Part
No.
Ref.
No.
Part
No.
Description
Qty
Description
Qty
1
2
3
4
184471
184481
109482
103972
COLLAR, wiper plate; sst
STEM, probe; sst
O-RING; PTFE
1
1
1
12
109479
PIN, spring, straight;
3/32 in. size x 3/8 in. (9.5 mm) long
NUT, retainer; sst
STEM, valve; sst
GUIDE, valve; sst
O-RING; fluoroelastomer
SCREW, cap, hex head;
5/16–18 unc–2a; 1/2 in. (13 mm) long
SEAL, valve; PTFE
WIPER; polyethylene
1
1
1
1
1
13
14
15n
16
17
184482
184479
184531
109458
109477
SCREW, drive, u-type;
0.188 in. (5 mm) long
PLATE, wiper; sst
WIPER; polyethylene
WIPER; nitrile/PTFE
SPACER; polyurethane
CLAMP, retaining; sst
NUT, lock, hex; w/nylon insert;
1/4–20 unc–2b
3
1
1
1
1
1
5
222915
184421
184552
276049
184477
109478
6n
7n
8
9
10
2
2
1
1
19n
20n
21
184530
184551
114317
VALVE, check, air assist
8
11
109506
ELBOW, tube fitting, 90_;
1/8 npt(m) x 1/4 in. (6.3 mm) tube size 1
n Keep these spare parts on hand to reduce down time.
308049
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
24
Model 241081, Series A
Carbon Steel Wiper Plate
with Buna-N Wiper
25
1
2
13
23
21
and UHMWPE Backup
4
14
3
16
19
12
5
15
9
0254D
6
Ref.
No.
Part
No.
Ref.
No.
Part
No.
Description
Qty
Description
Qty
1
2
3
101831
177542
100421
PIN, spring, straight
HANDLE
1
1
13
14
109458
102040
O-RING; fluoroelastomer
NUT, hex, self-locking;
with nylon insert; 1/4–20 unc–3b
WIPER; polyethylene
CLAMP, retaining;
zinc-plated carbon steel
SPACER; polyurethane
VALVE, check, air assist
FITTING, elbow, pipe 45_
UNION, adapter
1
SETSCREW, socket hd, cup point;
5/16–18 x 3/8 in. (9.5 mm) long
STEM, probe
WIPER; synthetic rubber
SCREW, machine, flat-hd;
zinc-plated carbon steel;
1/4–20 x 1 in. (25 mm) long
CLAMP, retaining
8
1
2
1
1
15n
16
194147
194149
4
5n
6
166560
194146
109469
1
1
1
1
1
1
19
21
23
24
25
276049
C20467
111842
155665
208391
8
1
1
9
194151
241080
zinc-plated carbon steel
PLATE, wiper;
zinc-plated carbon steel
VALVE, ball
12
n Keep these spare parts on hand to reduce down time.
18
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
21
1
2
Model 918409, Series B
Carbon Steel Wiper Plate
with Buna-N Wiper
13
20
19
and UHMWPE Backup
18
4
14
3
16
17
5
12
15
9
0254D
6
0254B
Ref.
No.
Part
No.
Ref.
No.
Part
No.
Description
Qty
Description
Qty
1
2
3
101831
177542
100421
PIN, spring, straight
HANDLE
1
1
13
14
109458
102040
O-RING; fluoroelastomer
NUT, hex, self-locking;
with nylon insert; 1/4–20 unc–3b
WIPER; polyethylene
CLAMP, retaining;
zinc-plated carbon steel
SPACER; polyurethane
FITTING, nipple, reducer
FITTING, elbow, pipe 45_
VALVE, ball
1
SETSCREW, socket hd, cup point;
5/16–18 x 3/8 in. (9.5 mm) long
STEM, probe
WIPER; synthetic rubber
SCREW, machine, flat-hd;
zinc-plated carbon steel;
1/4–20 x 1 in. (25 mm) long
CLAMP, retaining
8
1
2
1
1
15n
16
184421
184418
4
5n
6
166560
184420
109469
1
1
1
1
1
1
17
18n
19
20
21
276049
C20467
111842
208391
155665
8
1
1
9
184419
222764
zinc-plated carbon steel
PLATE, wiper;
zinc-plated carbon steel
UNION, adapter
12
n Keep these spare parts on hand to reduce down time.
308049
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
20
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
USE GENUINE GRACO PARTS AND ACCESSORIES
Wiper Conversion for Model 222812
Shield Kit 223689
If the fluid you are pumping is not compatible with the
184420 synthetic rubber wiper which is standard on
Model 222812, order part no. 184551 polyethylene
wiper and 184552 PTFE-coated wiper. These parts are
standard on Model 235516. Refer to page 13, items 5
and 20, for proper installation.
Place on the surface of the fluid before the plate enters
the pail, to cover the fluid side of the 19 liter (5 gal.)
wiper plate and keep it clean. For use with ram-
mounted pumps only. Package of 10 disposable poly-
ethylene shields. Shields may be reused, if desired, by
removing excess material with a squeegee.
Technical Data
Category
Data
Outer diameter (wiper)
Model 222812, 235516, 222909, 918409, C50260:
289 mm (11.38 in.);
Model 241081: 330 mm (12.99 in.)
Inner diameter (neck)
Wetted parts
64.58 mm (2.54 in.)
Model 222812, 241081, 918409, C50260: Zinc-Plated Carbon
Steel, Synthetic Rubber, Ultra-High Molecular Weight
Polyethylene, Cork, Polyurethane, Polyethylene, fluoroelastomer
Model 235516: Zinc-Plated Carbon Steel, Nitrile, PTFE,
Ultra-High Molecular Weight Polyethylene, Cork, Polyurethane,
Polyethylene, fluoroelastomer
Model 222909: 304 and 316 Stainless Steel, Nitrile, PTFE,
Ultra-High Molecular Weight Polyethylene, Polyurethane,
Polyethylene, fluoroelastomer
308049
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the
date of sale by an authorized Graco distributor to the original purchaser for use. With the exception of any special, extended, or limited
warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment
determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accor-
dance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection
with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured
by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide
purchaser with reasonable assistance in making any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the distributor closest to you:
Phone: 612–623–6921 or Toll Free: 1–800–328–0211 Fax: 612–378–3505
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 308049
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441
Copyright 1990, Graco Inc. is registered to ISO 9001
Revised 08/2010
22
308049
Download from Www.Somanuals.com. All Manuals Search And Download.
|