Instructions
306556S
EN
Topper Units
Grease dispense unit with pneumatic pump elevator for easy drum replacement. For
professional use only.
Model 226013
50:1 Ratio Fire-Ball Pump
Model 244637
75:1 Ratio President Pump
®
®
5000 psi (34.5 MPa, 345 bar) Maximum Working Pres-
sure
4000 psi (27.6 MPa, 276 bar) Maximum Working
Pressure
100 PSI (0.68 MPa, 6.89 bar) Maximum Air Pressure
80 PSI (0.55 MPa, 5.5 bar) Maximum Air Pressure
Model 226018
50:1 Ratio President Pump
Model 204490, Elevator and Inductor
without pump or hose kit
®
4000 psi (27.6 MPa, 276 bar) Maximum Working
Pressure
80 PSI (0.55 MPa, 5.5 bar) Maximum Air Pressure
Important Safety Instructions
Read all warnings and instructions in this
manual. Save these instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
Warnings
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-
tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When
these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific
hazard symbols and warnings not covered in this section may appear throughout the body of this manual where
applicable.
WARNING
FIRE AND EXPLOSION HAZARD
When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be
aware that flammable fumes can ignite or explode. To help prevent fire and explosion:
•
•
•
•
•
•
•
Use equipment only in well ventilated area.
Eliminate all ignition sources, such as cigarettes and portable electric lamps.
Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.
Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.
Ground all equipment in the work area.
Use only grounded hoses.
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment
until you identify and correct the problem.
•
Keep a working fire extinguisher in the work area.
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
•
Do not operate the unit when fatigued or under the influence of drugs or alcohol.
Do not exceed the maximum working pressure or temperature rating of the lowest rated system
component. See Technical Data in all equipment manuals.
•
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all
equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information
about your material, request MSDS forms from distributor or retailer.
Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-
facturer’s replacement parts only.
•
•
•
•
•
•
Do not alter or modify equipment.
Use equipment only for its intended purpose. Call your distributor for information.
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
Do not kink or over bend hoses or use hoses to pull equipment.
Keep children and animals away from work area.
Comply with all applicable safety regulations.
SKIN INJECTION HAZARD
High-pressure fluid from dispense valve, hose leaks, or ruptured components will pierce skin. This may
look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical
treatment.
•
•
•
•
Do not point dispense valve at anyone or at any part of the body.
Do not put your hand over the end of the dispense nozzle.
Do not stop or deflect leaks with your hand, body, glove, or rag.
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning,
checking, or servicing equipment.
306556S
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings
WARNING
TOXIC FLUID HAZARD
Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin,
inhaled, or swallowed.
•
•
Know the specific hazards of the fluid you are using.
Store hazardous fluid in an approved container. Dispose of hazardous fluid according to all local,
state, and national guidelines.
•
Always wear protective eye wear, gloves, clothing, and respirator as recommended by the fluid and
solvent manufacturer.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
•
•
Keep clear of moving parts.
Do not operate equipment with protective guards or covers removed.
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,
follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating
area of the equipment to help protect you from serious injury, including eye injury, hearing loss,
inhalation of toxic fumes, and burns. This equipment includes but is not limited to:
• Protective eyewear, and hearing protection.
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.
4
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
3. Connect the other end of the ground wire to a true
earth ground. (Fig 1).
Grounding
The equipment must be grounded to reduce the risk
of static sparking and electric shock. Electric or static
sparking can cause fumes to ignite or explode.
Improper grounding can cause electric shock.
Grounding provides an escape wire for the electric
current.
Z
Y
•
•
•
•
Pump: Use a ground wire and clamp as shown in
Fig 1.
FIG. 1
Air and fluid hoses: Use only electrically conductive
hoses.
Pressure Relief Procedure
Air Compressor: Follow manufacturer’s recommen-
dations.
Follow the Pressure Relief Procedure whenever
you see this symbol.
Spray fun and dispensing valve: Ground through
connection to a properly grounded fluid hose and
pump.
•
•
•
Fluid supply container: Follow your local code.
Truck bed or platform: Follow your local code.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief
Procedure when you stop spraying and before
cleaning, checking, or servicing the equipment.
Solvent pails used when flushing: Follow your local
code. Use only metal pails, which are conductive,
placed on a grounded surface. Do not place the pail
on a nonconductive surface, such as paper or card-
board, which interrupts the grounding continuity.
1. Close the pump’s air regulator.
•
To maintain grounding continuity when flushing or
relieving pressure: Hold a metal part of the dispens-
ing valve firmly to the side of a grounded metal pail,
then trigger the valve.
2. Close the supply pump’s bleed-type master air valve
(required in this system).
3. Hold a metal part of the dispensing valve firmly to a
grounded metal waste container and open the dis-
pensing valve until pressure is fully relieved.
Grounding the Pump
1. Remove the ground screw (Z) and insert through
the eye of the ring terminal at the end of ground wire
(Y).
If you suspect that the dispensing valve, extension, or
grease fitting coupler is clogged, or that pressure has
not been fully relieved after following the steps above,
VERY SLOWLY loosen the coupler or hose end cou-
pling and relieve pressure gradually, then loosen com-
pletely and clear the clog.
2. Fasten the ground screw back into the pump and
tighten securely.
306556S
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Typical Installation
3” (76 mm)
1” (25 mm)
supply lines
(from ceiling)
6” (152.4 mm)
supply lines
(through wall)
bleed-type
master air valve
high pressure
fluid shutoff valve
5’ (1524 mm)
mounting
holes
clearance
for plumbing
FIG. 2
The Typical Installation (shown in fig 2) is only a guide
for selecting and installing this system. It is not an actual
system design. Contact your local Graco representative
for assistance in designing a system to suit your particu-
lar needs.
4. Place the inductor plate (2, 18, or 22) on the mount-
ing base (102).
A
Positioning the Elevator
1. Position the elevator where the ceiling is at least 8 ft
(2.6 m) high. The elevator is 90 in (2.4 m) when fully
raised.
2. Provide adequate space in front of the elevator for
changing drums and in back and on the side for
plumbing.
102
Mounting the Elevator
103
104
105
1. Secure the elevator base (A) to the mounting base
(102) using screws (104), lockwashers (103), and
nuts (105). (Fig 3)
FIG. 3
5. Loosen the screws (68) of both support brackets
(83). Slide the support (64) down far enough to
allow installation of the pump in the inductor plate.
Tighten the bracket screws lightly.
2. Bolt the mounting base (102) to the floor for stability.
3. Verify the elevator is level. Loosen on or two screws
(104) on the elevator base and place shims under
the base, if necessary.
6
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
5. Tighten the lock nut (11 or 24) securely. Continue
Mounting the Pump
with Step 4 below.
Models 226013, 226018, 244637
pump riser
tube
8 or 23
11 or 24
2 or 22
pump intake
slots
86
0.12” (3.2 mm)
FIG. 5
NOTE: The full length of the pump intake slots must be
just below the bottom of the inductor cone.
Model 204490
FIG. 4
Refer to FIG. 6 for Steps 1-3 below.
2. Remove inductor plate nut (11 or 24), locking ring (8
or 23) and o-ring (9). (FIG. 5)
1. Lubricate the o-ring (20) in the inductor plate (18)
with light, waterproof grease. (FIG. 6)
3. In order, slide inductor plate nut (11 or 24), locking
ring (8 or 23) and o-ring (9) on pump riser tube.
(FIG. 5)
2. Mount the pump on the pump support (64) so the
fluid outlet faces front.
3. Guide the pump intake valve as far as possible into
the inductor plate, then tighten the set screws (19).
Continue with Step 4 below.
4. Adjust the inductor plate on the pump so that the
pump intake is 0.12 in. (3.2 mm) above the mount-
ing base.
20
19
18
FIG. 6
306556S
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
All Models
4. Connect one end of the 36 in. (914 mm) hose into
the adapter and the other hose end into the
4. Loosen the pump support clamps again and raise
the support (64) until it meets the pump base.
5. Secure the President or Fire-Ball pump to the pump
support mounting plates from the underside with the
screws (68).
The bleed-type master air valve is required in your
system to relieve air trapped between this valve and
the pump after the air is shut off. Trapped air can
cause the pump to cycle unexpectedly and cause
serious injury, including splashing in the yes or on the
skin. Position the valve close to the pump.
6. Tighten screws (68) on lower pump bracket (83).
7. Slide the upper support bracket (83) up or down (the
tubing of the pump support (64) will flex slightly)
until the pump is in a true vertical position.
85
89
8. Tighten the screws (68) on the upper bracket.
68
64
83
27
FIG. 7
Installing the Hoses and Valves
E
NOTE: Use thread sealant on all male threads except at
the swivel unions.
FIG. 8
5. Route the hose inside the arms of the pump support
1. Remove the plug from the top of the elevator cap
and screw it into the air inlet (E) in the elevator base.
6. Screw the hex nipple (115 or 99) from the outlet
hose kit (91 or 97) to the pump outlet. (See Parts
1. Screw the restrictor valve assembly (42) into the
elevator cap.
7. Connect the kit’s swivel union (96) to the adapter
with the opening in the valve (94) facing down. (See
2. Screw the 1/4 x 1/8 npt adapter (85) into the restric-
8
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
8. Install a bleed-type master air valve on the pump’s
air supply line.
9. Install a fluid shutoff valve on the fluid supply line to
shut off fluid to the pump.
10. Finish assembling the hoses and fittings as shown
306556S
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operation
NOTE: To adjust the elevator speed, turn the restrictor
valve screw (46) clockwise to decrease the speed or
counter clockwise to increase the speed.
NOTICE
Always close the ball valve (65) as soon as the
inductor plate reaches the bottom of the drum, indi-
cating the drum is empty. Allowing the pump to run
without fluid will cause damage to the pump.
6. Center an opened 400 lb (181.4 kg) drum under the
inductor plate so the drum bottom touches the ele-
vator base (A).
Installing a Drum
7. Make the top of the fluid concave by scooping fluid
from the center to the sides of the container.
8. Loosen the setscrews (73), holding pump mounting
plates to the mounting bracket (C). Align the pump
and inductor plate with the drum.
NOTE: Keep your fingers and hands away from the
sides of the drum or inductor plate to avoid pinching
them when raising and lowering the pump.
1. Relieve the pressure, see Pressure Relief Proce-
dure, page 5.
2. Close the ball valve (65). The handle will be at a 90°
angle to the valve body.
9. Push in the snap-over valve (27) to lower the pump
while guiding the inductor plate into the drum.
3. Open the bleed-type master air valve (F).
10. Press down the pump and rock it back and forth to
seat the inductor plate. This helps eliminate air
trapped beneath the plate. Continue this action until
fluid appears at the vent opening (D).
4. Open the inductor plate vent by turning the knob
(10) counter clockwise.
5. Pull open the snap-over valve (27) to raise the ele-
vator.
11. Be sure that the pump is aligned vertically and
tighten the set screws (73).
46
12. Close the inductor plate vent by turning the knob
(10) clockwise.
F
13. For Models 226013, 226018, and 244637 only:
73
a. Open the bleeder valve (94) at the pump outlet
by turning the thumbscrew counter clockwise.
b. Open the ball valve (65) until all air trapped in
the pump and under the plate are pumped
through the valve.
65
94
C
47
27
c. Close the ball valve and the bleeder valve.
A
10
d. Regulate the pump speed with the ball valve
handle.
D
14. All Models: Always use the lowest possible pump
pressure necessary for good delivery. Higher pres-
sures cause premature pump wear and usually do
not produce better results.
FIG. 9
10
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Removing a Drum
1. Relive pressure, see Pressure Relief Procedure,
2. Press in and hold the air-assist valve (47) until the
inductor plate rises above the drum. Release the
3. Open the snap-over valve (27) and raise the eleva-
NOTE: If you lose air pressure when reaching the drum
chime, continue holding the air-assist valve and slowly
pull out the snap-over valve until the chime is passed.
Then, immediately close the snap-over valve to prevent
raising the drum off the floor.
306556S
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Maintenance
NOTE: To avoid contaminating the fluid in the supply
container, keep the pump intake and the inductor plate
clean during the servicing operations. Place the parts on
clean paper or rags.
Removing the Pump
27
1. Relieve Pressure, see Pressure Relief Procedure,
41
11 or 24
2. Remove the drum. Disconnect the air-assist hose
(41).
For Model 204490: Loosen the inductor plate set
screws (19).
For Models 226013, 226018, and 244637: Unscrew
the locking nut (11 or 24), taking note of the number
of turns needed.
3. Push the snap-over valve (27) to lower the pump.
FIG. 10
4. Relieve pressure in the pump and disconnect the
hoses.
5. Disconnect the pump from the mounting bracket
and remove it.
Reinstalling the Pump
1. Connect the pump to the mounting bracket.
2. Attached hoses to pump.
3. Pull the snap-over valve (27) to raise the pump.
NOTE: When attaching the pump to the inductor plate,
turn the locking nut (11 or 24) the same number of turns
noted in Removing the Pump, Step 2, or until you feel it
settle in.
12
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Problem
Cause
Solution
1. Close the inductor plate.
1. Open inductor plate vent
2. Loose inductor plate sleeve lock- 2. Tighten the locking nuts.
Low flow or air sucked into pump or
under inductor plate.
ing nut
3. Replace seals; See Parts Draw-
3. Worn inductor seals
Worn o-rings or seals
Remove valve, place in vise, disas-
semble and replace parts as
needed.
Failure of snap-valve or air-assist
valve
306556S
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Parts
Model 204490
Model 244637
Elevator and Inductor Plate Assembly
Includes items 17, 25, 90, and 101
Pump, Elevator, and Inductor Plate Assembly
Includes items 21, 25, 90, 97, 101, and 107
Ref Parts
Ref
No. No.
Description
Qty.
No. Part No. Description
Qty.
17 204405 INDUCTOR PLATE ASSEMBLY
See parts on page 14
25 204461 WISHBONE SUPPORT ASSEMBLY
See parts on page 16
90 204385 PNEUMATIC ELEVATOR
See manual 306287 for parts
101205339 ELEVATOR BASE
See parts below
1
21 205669 INDUCTOR PLATE ASSEMBLY
See Parts on Page 14
25 204461 WISHBONE SUPPORT ASSEMBLY
See parts on page 16
90 204385 PNEUMATIC ELEVATOR
See manual 306287 for parts
97 205102 HOSE KIT
See parts on page 18
101 205339 ELEVATOR BASE
See parts below
107 239730 75:1 RATIO PRESIDENT PUMP
See manual 308777 for parts
1
1
1
1
1
1
1
1
1
Model 226013
Pump, Elevator, and Inductor Plate Assembly
Includes items 1, 25, 89, 90, 91 and 101
Ref No. 101: Part No. 205339
Elevator Base Assembly
Includes items 102 - 105
Ref
No. Part No. Description
1
Qty.
204353 INDUCTOR PLATE ASSEMBLY
See parts on page 14
1
Ref
25 204461 WISHBONE SUPPORT ASSEMBLY
See parts on page 16
89 239888 50:1 RATIO FIRE-BALL PUMP
See manual 308883 for parts
90 204385 PNEUMATIC ELEVATOR
See manual 306287 for parts
91 204467 HOSE KIT
1
1
1
1
1
No. Part No. Description
102 205340 BASE, elevator
103 100018 LOCKWASHERS, spring, 1/2”
104 100096 SCREW, hex hd cap, 1/2-13 x 2”
105 100321 NUT, 1/2-13
Qty.
1
4
4
4
See parts on page 18
101 205339 ELEVATOR BASE
See parts below
90
89, 106, or 107
Model 226018
Pump, Elevator, and Inductor Plate Assembly
Includes items 21, 25, 90, 97, 101, and 106
Ref
No. Part No. Description
21 205699 INDUCTOR PLATE ASSEMBLY
See part on page 14
25 204461 WISHBONE SUPPORT ASSEMBLY
See parts on page 16
90 204385 PNEUMATIC ELEVATOR
See manual 306287 for parts
97 205102 HOSE KIT
See parts on page 18
101 205339 ELEVATOR BASE
See parts below
106 205395 50:1 RATIO PRESIDENT PUMP
See manual 306674 for parts
Qty.
91 or 97
1
102
1
1
1
1
1
103
104
105
1, 17, or 21
14
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref No. 1: Part No. 204353
6
Inductor Plate Assembly: 400 lb Drum size
Fits 50:1 Fire-Ball In-Line Pump; Includes items 2-16
Ref No.Part No. Description
4
10
3
14
Qty.
11
8
2
3
4
5
6
7
204502
100015
100021
104663
100799
100859
PLATE, inductor, bare
NUT, hex, mscr, 1/4-20 UNC-2a
CAPSCREW, hex hd, 1/4-20 UNC-2a x 1”
PLUG, pipe, 3/4 npt (f)
SCREW, mach, rd hd, 1/4-20 x 1/2”
SCREW, headless, full dog point, No.
10-24 x 1/4”
1
1
1
1
18
1
16
Tapered
15
7
shoulder
faces up
9
8
9
101644
158776
160865
161107
161162
161287
161288
164432
164497
SLEEVE, coupling
O-RING
KNOB, vent
NUT, locking
1
1
1
1
1
1
6
1
1
5
12
10
11
12
13
14
15
16
SEAL, rubber
13
WIPER, inductor plate
SEGMENT, full barrel
CAP, vent
Ref No. 1
2
ROD, vent release
Ref No. 17: Part No. 204405
Inductor Plate Assembly: 400 lb Drum size
Fits Monarch and President In-Line Pumps
Includes items 3 - 7, 10, 12 - 16, 18 - 20
Ref No.Part No. Description
4
10
3
6
14
Qty.
16
3
4
5
6
7
100015
100021
104663
100799
100859
NUT, hex, mscr, 1/4-20 UNC-2a
CAPSCREW, hex hd, 1/4-20 UNC-2a x 1”
PLUG, pipe, 3/4 npt (f)
SCREW, mach, rd hd, 1/4-20 x 1/2”
SCREW, headless, full dog point, No.
10-24 x 1/4”
1
1
1
18
1
15
7
20
5
10
12
13
14
15
16
18
19
160865
161162
161287
161288
164432
164497
204507
100556
KNOB, vent
SEAL, rubber
WIPER, inductor plate
SEGMENT, full barrel
CAP, vent
1
1
1
6
1
1
1
2
12
19
13
ROD, vent release
PLATE, inductor, bare
SETSCREW, sq hd cup point, 5/16-18 x
3/8”
18
Ref No. 17
20
160721
O-RING, nitrile rubber
1
Ref No. 21: Part No. 205699
Inductor Plate Assembly: 400 lb Drum size
Fits 50:1 President In-Line Pumps
6
10
3
4
14
Includes items 3 - 7, 10, 12 - 16, and 22 - 24
24
16
Ref No.Part No. Description
Qty.
23
9
3
4
5
6
7
100015
100021
104663
100799
100859
NUT, hex, mscr, 1/4-20 UNC-2a
CAPSCREW, hex hd, 1/4-20 UNC-2a x 1”
PLUG, pipe, 3/4 npt (f)
SCREW, mach, rd hd, 1/4-20 x 1/2”
SCREW, headless, full dog point, No.
10-24 x 1/4”
1
1
1
18
1
15
Large taper
faces up
7
5
10
12
13
14
15
16
22
23
24
160865
161162
161287
161288
164432
164497
205698
196219
164962
KNOB, vent
SEAL, rubber
WIPER, inductor plate
SEGMENT, full barrel
CAP, vent
ROD, vent release
PLATE, inductor, bare
RING, locking
1
1
1
6
1
1
1
1
1
12
13
Ref No. 21
22
NUT, collet
306556S
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
aa
Ref. No. 27
Ref. No. 42
29
36
32
Snap-Over Valve Assembly
Includes items 28 to 40
Restrictor Valve Assembly
Includes items 43 to 46
43
46
35
34
28
40
33
38
30
44
45
37
39
1/8 npt
31
0729
0730
85
42
89
62
69
68
83
70
64
83
86
61
73
79
90
65
63
82
84
27
41
0732B
88
74
49
77
62
66
87
Ref. No. 47
47
Air Assist Valve Assembly
60
Includes items 48 to 60
50
56
3/8 npt
52
58
51
57
53
78
59
55
48
1/4 npt
54
0731
16
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref No. 25: Part No. 204461
Wishbone Support Assembly
Ref
No.
61
Ref
No.
27
Part No. Description
204560 HOSE, air, cpld 3/8 npt (m) 3/8”
(9.6mm) ID, 18” (457 mm) long
204561 HOSE, air, cpld 3/8 npt (m) 3/8”
(9.6mm) ID, 36” (914 mm) long
205610 SUPPORT, pump, lower
205611 SUPPORT, pump, upper
208393 BALL VALVE
100016 LOCKWASHER, spring, 1/4”
100057 CAPSCREW, hex hd, 5/16-18 x 3/4”
100181 NUT, square, 6/16-18
100214 LOCKWASHERS, 5/16”
100333 CAPSCREW, hex hd, 1/4-20 x 1/2”
100469 CAPSCREW, hex hd, 3/8-16 x 3/4”
100421 SETSCREW, socket hd, cup point,
5/16” x 3/8”
100377 SCREW, hex socket hd, 1/4-20 x 5/8”
150718 CLAMP, drum
151243 ADAPTER, 1/8 npt(m)
155541 UNION, 90° street, 1/4 npt (m x f)
swivel
155677 UNION, 90° adapter, 3/8 npt (f)
155699 ELBOW, street, 3/8 npt (m x f)
156580 ADAPTER, 3/8 npt(f) x 1/8 npt(m)
156823 UNION, 1/4 npt(m x f) swivel
158271 BRACKET, elevator riser tube, 1/8 npt
158962 ELBOW, 90° street, 1/4 npt(f) x 1/8 npt
(m)
159840 ADAPTER, pump mounting, 1/4 npt(f) x
1/8 npt(m)
189211 BRACKET, pump mounting
161466 MANIFOLD, air
162505 UNION, swivel, 3/8 npt(m) x 1/2
npsm(f) swivel
150287 ADAPTER, 1/4 npt(m) x 3/8 npt(f)
158256 UNION, swivel, 1/2 npt(m) x 3/8
npsm(f) swivel (used with model
226018 President pump only)
Qty.
Part No. Description
202295 SNAP-OVER VALVE ASSEMBLY
Includes items 28 - 40
100272 LOCKWASHER, int. shkprf, No. 6
104560 SCREW, oval hd, 6-32 3/8”
154519 KNOB
Qty.
1
62
2
28
29
30
31
32
33
34
35
36
37
38
39
40
41
1
1
1
1
1
1
1
1
1
1
1
1
1
1
63
64
65
66
68
69
70
71
72
73
1
1
1
4
11
4
4
4
4
4
154526 WASHER
154570 WASHEr
154594 O-RING, buna-N
155500 O-RING, nitrile rubber
155811 SEAL, valve, nitrile rubber
155921 SEAL, valve, nitrile rubber
157160 HOUSING, valve
157161 GUIDE, valve
161129 STEM, valve, large
161132 STEM, valve, small
205418 HOSE, air, cpld 1/2 npt(m) 1/2” (13mm)
ID, 6’ (1.8 m) long
203743 RESTRICTOR VALVE ASSEMBLY
Includes items 43 - 46
101448 NUT, jam, 3/8-24
157628 O-RING, nitrile rubber
160162 HOUSING, valve
160163 NEEDLE VALVE
74
76
77
78
2
4
1
1
42
1
43
44
45
46
47
1
1
1
1
1
79
80
81
82
83
84
1
1
1
1
2
1
203842 AIR ASSIST VALVE ASSEMBLY
Includes items 48 - 60
48
49
50
51
52
53
54
55
56
57
58
59
60
100063 PIN, cotter, 1/6” dia x 1/2”
100068 LOCKWASHERS, spring, No. 6
100072 NUT, hex, No. 6-32
150902 SPRING, compression
153348 GASKET, copper
154519 KNOB
154594 O-RING, buna-N
155500 O-RING, nitrile rubber
155811 SEAL, valve, nitrile rubber
157161 GUIDE, valve
1
1
1
1
1
1
1
1
1
1
1
1
1
85
1
86
87
88
2
1
1
89
90
1
1
160401 STEM, valve
160402 HOUSING, valve
160404 STUD, valve
MOUNTING and CONNECTING PARTS
0734
0733
1/8 npt
3/8 npt
REF. NO.
QTY.
81
80
1
76
4
68
11
71
4
72
4
1
306556S
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts
Ref No. 91: Part No. 204467
Fire-Ball Delivery Hose Kit
Includes items 92 - 94, 96, and 115
Ref No. 97: Part No. 205102
President Delivery Hose Kit
Includes items 94, 96, 98, 99, and 110
Ref
Ref
No. Part No. Description
Qty.
No. Part No. Description
Qty.
92
93
100206 BUSHING, 1/2 npt(m) x 1/4 npt(f)
109150 HOSE, fluid, cpld 1/4 npt(m)), 1/4”
(6.4mm) ID, 6’ (1.83 m) long
205528 VALVE, bleeder
160878 UNION, 90°, 1/4 npt(f) swivel
1
1
94
96
98
205528 VALVE, bleeder
1
1
1
160878 UNION, 90°, 1/4 npt(f) swivel
109163 HOSe, cpld 3/8 npt(m), 3/8”
(9.6mm) ID, 6’ (1.83 m) long
94
96
1
1
1
99
156849 NIPPLE, hex, 3/8 npt(m)
1
1
115 156971 NIPPLE, 1/4 x 1/4 npt(m)
110 100081 BUSHING, pipe, 1/2 npt(m) x 3/8
npt(f)
98
94
93
1/2 npt
94
1/2 npt
99
115
92
3/8 npt 96
1/4 npt 96
110
Dimensions
90” (2.3 m) Maximum Height
56” (1.4 m) Minimum Height
30” (762 mm)
24” (610 mm)
18
306556S
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Technical Data
See the pump instruction manual for Technical Data including Wetted Parts, Port Sizes, and so on.
.
Topper Units
US
Metric
Maximum fluid working pressure
50:1 Ratio Fire-Ball Pump
50:1 Ratio President Pump
75:1 Ratio President Pump
5000 psi
4000 psi
34.5 MPa, 345 bar
28 MPa, 280 bar
28 MPa, 280 bar
4000 psi
Maximum air pressure
50:1 Ratio Fire-Ball Pump
50:1 Ratio President Pump
75:1 Ratio President Pump
100 psi
80 psi
0.7 MPa, 7bar
0.6 MPa, 6 bar
0.6 MPa, 6 bar
80 psi
122 lb
136 lb
136 lb
90 lb
Weight
Model 226013
50:1 Ratio Fire-Ball Pump
55 kg
61 kg
61 kg
41 kg
Model 226018
50:1 Ratio President Pump
Model 244637
75:1 Ratio President Pump
Model 204490
Elevator and Inductor
Maximum sound pressure tested at 100 psi (0.7 MPa, 7 bar) at 40 cycles per minute
Model 226013
50:1 Ratio Fire-Ball Pump
77.8 dB(A)
Maximum sound pressure tested at 100 psi (0.7 MPa, 7 bar) at 15 cycles per minute
Model 226018
50:1 Ratio President Pump
80.9 dB(A)
Model 244637
75:1 Ratio President Pump
80.9 dB(A)
Maximum sound power lever tested in accordance with ISO 9614-2
Model 226013
50:1 Ratio Fire-Ball Pump
85.6 dB(A)
Maximum sound power lever tested in accordance with ISO 9614-2
Model 226018
50:1 Ratio President Pump
94.6 dB(A)
94.6 dB(A)
Model 244637
75:1 Ratio President Pump
306556S
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or
maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Information
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.
Phone: 612-623-6928 or Toll Free: 1-800-533-9655, Fax: 612-378-3590
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 306556
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 1956, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
Revised November 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|