Graco Heat Pump 310643u User Manual

Repair  
310643U  
Displacement Pump  
EN  
Use only genuine Graco replacement parts. Use of non-Graco replacement parts may void  
warranty.  
3300 psi (22.7 MPa, 227 bar) Maximum Working Pressure  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Be familiar with the controls and the proper usage  
of the equipment. Save these instructions.  
Model 248204, Series A  
UltraMax II and Ultimate MX II 695/795  
ASM Zip-Spray 2700 Plus, 3100 Plus  
ASM AllPro Mach 8600 Plus and 11000 Plus  
ASM H2700 Plus  
Model 255968, Series A  
ASM 3600G Plus  
Model 248205, Series A  
UltraMax II and Ultimate MX II 1095/1595  
Model 249059, Series A  
TexSpray Mark V  
Model 249057, Series A  
TexSpray Mark V  
Model 277069, Series A  
LineLazer IV 3900, R300  
Model 277070, Series A  
LineLazer IV5900  
Model 253056, Series A  
Mark IV  
Model 257146, Series A  
Ironman 300E and Ironman 500G  
ti2311  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
Service  
Pressure Relief Procedure  
Pump Repair Kits  
Follow the Pressure Relief Procedure whenever  
you see this symbol.  
Pump  
Repair Kit  
248204, 255968  
253056  
248212  
287825  
248205, 249057, 249059, 248213  
257146  
This equipment stays pressurized until pressure is  
manually relieved. To help prevent serious injury from  
pressurized fluid, such as skin injection, splashing  
fluid and moving parts, follow the Pressure Relief  
Procedure when you stop spraying and before  
cleaning, checking, or servicing the equipment.  
Tools Needed  
Vise  
12 in. adjustable, open-end wrench (2)  
Hammer (20 oz maximum)  
Small screwdriver  
1. Engage trigger lock.  
Throat Seal Liquid  
2. Turn ON/OFF switch to OFF.  
3. Unplug power cord.  
Pick or long small screwdriver  
Cleaning and Inspecting Parts  
4. Disengage trigger lock. Hold metal part of gun  
against grounded metal pail and trigger gun into pail  
to relieve pressure.  
Clean and inspect parts. Pay particular attention to the  
ball seats in the intake valve and piston, which must  
have no nicks or wear, and to the inside of the sleeve  
and the outside of the piston rod, which must not be  
worn or scratched. Replace worn or damaged parts.  
5. Engage the trigger lock.  
6. Open all fluid drain valves in the system, having a  
waste container ready to catch drainage. Leave drain  
valve(s) open until you are ready to spray again.  
7. If you suspect the spray tip or hose is clogged or  
that pressure has not been fully relieved after follow-  
ing the steps above, VERY SLOWLY loosen tip  
guard retaining nut or hose end coupling to relieve  
pressure gradually, then loosen completely. Clear  
hose or tip obstruction.  
COMPONENT RUPTURE HAZARD  
To reduce the risk of serious injury from pressurized  
fluid, never use sharp or pointed tools to remove  
sleeve. If the sleeve cannot be removed easily, return  
the sleeve and cylinder to a Graco distributor for  
removal.  
NOTE: Remove and clean sleeve when repacking pump.  
310643U  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Service  
4. Tap piston rod out of cylinder with a hammer or flip  
over and tap piston rod out against a bench.  
Repair When Pump is Separated  
From Sprayer  
Disassembling the Pump  
NOTE: Sleeve may come out  
of cylinder with piston rod.  
1. Remove packing nut (202) and o-ring (228).  
202  
228  
ti7571a  
5. Remove piston rod from sleeve, or remove sleeve  
from cylinder. Mark IV models: Remove sleeve  
spacer (230) from sleeve.  
ti7566a  
2. Unscrew intake valve from cylinder.  
ti7572a  
ti7569a  
3. Disassemble intake valve. Clean and inspect o-ring  
(227). NOTE: A pick may be required to remove  
o-ring.  
233  
215  
214  
212  
227  
213  
ti23115a  
4
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
8. Remove throat packings and glands from cylinder.  
Discard throat packings and glands.  
Not  
used on  
248204,  
253056,  
255968  
COMPONENT RUPTURE HAZARD  
To reduce the risk of serious injury from pressurized  
fluid, do not clean or wipe the piston valve threads.  
Cleaning the piston valve threads could destroy the  
special sealing patch and cause the piston valve to  
come loose during operation.  
6. Unscrew piston valve from piston rod. Clean and  
inspect parts. The piston has a special thread lock-  
ing/sealing patch. Do not remove the patch. The  
patch allows four disassembly/assembly procedures  
before it is necessary to apply thread sealant to the  
threads.  
ti7573b  
Assembling the Pump  
1. Soak all leather packings in SAE 30W oil for 1 hour  
minimum prior to assembly. Stack male gland (204)  
on piston rod. Alternately stack UHMWPE (208) and  
leather (218) packings (note orientation) on piston  
rod. Install female gland (217). Install piston wiper  
(216) (note orientation) and backup washer (229) on  
piston valve (210). Threads are good for four  
repackings. Use thread sealant on piston valve  
threads after four repackings.  
Not  
ti7576a  
used on  
248204,  
210  
253056,  
255968  
7. Remove packings and glands from piston rod.  
229  
216  
Not  
used on  
248204,  
253056,  
255968  
217  
ti7574d  
218 204 208  
ti3940b  
310643U  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
2. Install ball (206) in piston rod. If thread sealant is  
applied to piston valve threads, make sure that none  
gets on ball.  
4. Soak all leather packings in SAE 30W oil for one  
hour minimum prior to assembly. Place male gland  
(204) in cylinder. Alternately stack UHMWPE (203)  
and leather packings (223) (note orientation). Place  
female gland (224) in top of cylinder seat packings.  
206  
Not  
224  
used on  
248204,  
253056,  
255968  
203  
223  
204  
ti7573f  
t
5. Install seal (201) into packing nut (202). Install  
o-ring (228) onto packing nut. Loosely install pack-  
ing nut into cylinder.  
3. Tighten piston valve to piston rod as specified:  
Models  
Torque  
248204, 253056,  
255968, 244069  
248205, 249057,  
249059, 277070,  
257146  
27 +/-3 ft-lb.(36.1 +/-4.1 N•m)  
201  
202  
228  
55 +/-3 ft-lb.(74.6 +/-4.1 N•m)  
ti7581a  
6. Grease piston packings.  
ti7576a  
ti7578c  
NOTICE  
Do not slide piston assembly into top of sleeve as this  
may damage piston packing.  
6
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
7. Slide piston assembly into bottom of sleeve.  
10. Mark IV models: Install o-ring (231) on sleeve  
spacer (230) and install sleeve spacer on sleeve.  
230  
231  
ti7577a  
ti7340a  
ti7340b  
8. Grease top inch or two of piston rod that will go  
through the cylinder throat packings.  
11. Reassemble intake valve with new o-ring (227),  
seat (212) and ball (214). Seat may be flipped over  
and used on other side. Clean seat thoroughly.  
215  
214  
212  
227  
ti7579a  
9. Grease o-rings (221) and place on sleeve. Slide  
sleeve/piston rod assembly into bottom of cylinder.  
Replace o-ring (207) if desired.  
213  
NOTE: O-ring (207) is not required for safe pump  
ti23115a  
operation.  
207  
221  
ti7582a  
310643U  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
12. Install intake valve on cylinder. If a wrench is used  
torque as follows:  
14. Remove o-ring (228) when pump packings begin to  
leak after extended use. Then tighten packing nut  
down until leakage stops or lessens. This allows  
approximately 100 gallons of additional operation  
before a repacking is required.  
Models  
Torque  
248204, 253056, 67 +/- 5 ft-lb (90.8 +/-6.8 N•m)  
255968, 277069  
248205, 249057, 80 +/- 5 ft-lb (108.5 +/-6.8 N•m)  
249059, 277070,  
257146  
202  
228  
ti7568a  
ti7569a  
13. Torque packing nut (202) down onto adjustment  
spacer (228) 100 +/- 10 in-lb. (11.3 +/- 1.1 N•m)  
8
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
4. Push out pin (29).  
Repair When Pump is On  
Sprayer  
29  
1. Perform Pressure Relief Procedure, page 3.  
2. Remove intake valve.  
26  
ti4258b  
ti4258b  
5. Disassemble intake valve. Clean and inspect.  
O-ring (227) may require a pick for removal.  
215  
214  
212  
227  
ti4258c  
3. Push up retaining spring (26).  
213  
ti23115a  
6. Remove piston rod and sleeve.  
ti4258a  
26  
ti7746a  
310643U  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
7. Invert piston rod and sleeve and pound on hard sur-  
face until piston rod comes out of sleeve.  
11. Remove piston valve from piston rod with a wrench.  
Mark IV models: Remove sleeve spacer from sleeve.  
ti4258g  
ti4258g  
12. Remove pin and piston rod from cylinder.  
ti7572a  
8. Remove packing nut (202).  
202  
ti4258h  
13. Soak all leather packings in SAE 30W oil for 1 hour  
minimum prior to assembly. Stack male gland (204).  
Alternately stack UHMWPE (203) and leather (223)  
packings (note orientation). Install female gland  
(224). Install seal (201) and packing nut (202) and  
o-ring (228).  
ti7726a  
9. Invert piston rod and insert into cylinder to force out  
throat packings.  
Not used on  
248204,  
253056,  
224  
255968  
201  
203  
223  
204  
228  
202  
ti4258e  
10. Insert piston rod into cylinder with pin hole up and  
piston valve down. Insert pin into piston rod and  
crank shaft.  
ti7573c  
ti4258f  
10  
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
14. Remove packings and glands from piston rod.  
16. Install ball (206) in piston rod. NOTE: If thread seal-  
ant is applied to piston valve threads, make sure  
none gets on ball. Install piston valve on piston rod.  
Torque as follows:  
Not used on  
248204,  
253056,  
Models  
Torque  
255968  
248204, 253056,  
255968, 277069  
248205, 249057,  
27 +/- 3 ft-lb (36.6 +/-4.1 N•m)  
249059, 277070, 55 +/- 3 ft-lb (74.6 +/-4.1 N•m)  
257146  
ti3939a  
15. Soak all leather packings in SAE 30W oil for one hour  
minimum prior to assembly. Stack male gland (219)  
on piston rod. Alternately stack UHMWPE (208)and  
leather (218) packings (note orientation) on piston  
rod. Install female gland (217). Install piston wiper  
(216) and backup washer (229) (note orientation) on  
piston valve (210). The special sealing patch on pis-  
ton valve threads is good for four repackings. Use  
thread sealant on piston valve threads after four  
repackings.  
206  
219  
217  
ti7575b  
Not  
used on  
ti7575b  
216  
248204,  
253056,  
17. Grease piston packings.  
229  
255968  
206  
210  
218  
208  
ti3941a  
ti7578c  
310643U  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
21. Torque seal and packing nut (202) down onto throat  
adjustment spacer (228) to 100 +/- 10 in-lb (11.3 +/-  
1.1 N•m).  
NOTICE  
Do not slide piston assembly into top of sleeve as this  
may damage piston packing.  
Remove o-ring when pump packings begin to leak  
after extended use. Then tighten packing nut down  
until leakage stops or reduces. This allows approxi-  
mately 100 gallons of additional operation before a  
repacking is required.  
18. Slide piston assembly into bottom of sleeve. Make  
sure V-packing and u-cup are not rolled over or  
damaged. Mark IV models: Install o-ring (231) on  
sleeve spacer (230). Install sleeve spacer on  
sleeve.  
Mark IV  
202  
228  
ti7726b  
ti7341a  
22. Push up retaining spring (26) with screwdriver.  
19. Grease top inch or two of piston rod that will go  
through the cylinder throat packings.  
ti4258k  
26  
ti7579a  
23. Push in pin (29). NOTE: Make sure retaining ring  
falls into slot.  
20. Grease o-ring (221) and place on sleeve. Slide  
sleeve/piston rod assembly into bottom of cylinder.  
Replace o-ring (207) if desired. NOTE: O-ring (207)  
is not required for safe pump operation.  
29  
26  
ti4258m  
207  
221  
ti4258j  
12  
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Service  
24. Reassemble intake valve with new o-rings (227)  
and (230), seat (212) and ball (214). Seat may be  
flipped over and used on other side. Clean seat  
thoroughly.  
Pump Packings  
222  
201  
215  
214  
202  
228  
212  
227  
224  
203  
204  
V-Max  
223  
Leather  
UHWMPE,  
blue  
205  
213  
221  
220  
ti23115a  
206  
207  
219  
25. Install intake valve on cylinder. Torque as follows:  
Models  
Torque  
208  
217  
216  
218  
Leather  
248204, 253056,  
255968, 277069  
248205, 249057,  
70 +/- 5 ft-lb (94.9 +/-6.8 N•m)  
V-Max  
210  
UHWMPE,  
blue  
229  
249059, 277070, 80 +/- 5 ft-lb (108.5 +/-6.8 N•m)  
257146  
221  
215  
214  
213  
212  
227  
230  
Pump 248204  
ti7683d  
ti4258n  
310643U  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Parts - Pump 248204, 277069, 255968  
Parts - Pump 248204, 277069, 255968  
Series A  
Ref.  
201  
202  
Part  
179810  
193046  
Description  
SEAL, throat  
NUT, packing  
V-PACKING, throat, V-Max,  
UHMWPE, blue  
Qty.  
201  
1
1
3
203* 192692  
202  
228  
221  
222  
204* 15C987 GLAND, male, throat,  
205  
1
CYLINDER, pump  
Model 248204, 255968  
Model 16X428  
BALL, sst, 0.3125 in.  
PACKING, o-ring  
V-PACKING, piston, V-MAX,  
UHMWPE, blue  
243346  
243346  
1
1
1
1
3
206* 105444  
207* 114054  
208* 192693  
224  
210  
239932  
VALVE, piston  
KIT, seat, carbide (includes 214 and  
227)  
1
1
223  
212239922  
219  
218  
203  
204  
213  
VALVE, intake (foot)  
15C785 Model 248204, 255968  
1
195892  
Model 277069  
214*105445* BALL, sst. 0.5000 in.  
215  
1
1
1
1
2
1
1
2
1
2
208  
192624  
GUIDE, ball  
WIPER, piston  
GLAND, female, piston  
V-PACKING, leather, piston  
GLAND, male  
SLEEVE, cylinder  
O-RING, ptfe  
216* 118503  
217* 178969  
218* 178939  
219* 196880  
220  
221* 108526  
222 248206  
223* 178940  
224* 15C988 GLAND, female  
227*107079  
228 192714  
229* 15C997 WASHER, backup  
230* 118494 O-RING, fluoroelastomer  
(not used on Lo-Boy)  
217  
216  
248209  
229  
ROD, piston  
V-PACKING, leather, throat  
206  
210  
PACKING, o-ring  
SPACER, throat, nut  
1
1
1
1
215  
205  
214  
227  
* These parts are also included in Repair Kit 248212, which  
may be purchased separately.  
212  
213  
207  
221  
† These parts are also included in Carbide Seat Kit 239922,  
which may be purchased separately.  
220  
(Not an O-ring groove)  
230  
ti4255a  
14  
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Parts - Pump 248205, 249057, 249059, 277070, 257146  
Parts - Pump 248205, 249057, 249059, 277070, 257146  
Series A  
Ref.  
Part  
Description  
Qty.  
201  
202  
203*  
183171  
193032  
193124  
PLUG  
NUT, packing  
V-PACKING, throat, V-Max,  
UHMWPE, blue  
GLAND, packing, male, throat  
CYLINDER, pump  
Model 248205, 277070  
Model 249057, 249059, 257146  
BALL, 0.375 in.  
1
1
4
201  
202  
221  
222  
204*  
205  
15C989  
1
1
243347  
196754  
228  
224  
203  
206  
1
101947*  
Model 248205, 249057, 277070, 257146  
116327Model 249059, ceramic  
156633  
193125  
219  
218  
207*  
208*  
PACKING, o-ring  
V-PACKING, piston, V-MAX,  
UHMWPE, blue  
1
4
208  
223  
210  
212  
240150  
VALVE, piston  
1
1
KIT, seat, carbide (includes 214, 227)  
Model 248205, 249057, 277070, 257146  
Model 249059  
244199  
244571  
217  
216  
229  
206  
213  
214  
215  
HOUSING, intake (foot)  
Model 248205  
Model 249059, 249057  
Model 277070, 257146  
BALL  
1
1
15C783  
196753  
195894  
204  
222  
102972*Model 248205, 249057, 277070, 257146,  
0.875 in.  
111453Model 249059, ceramic, 0.750 in.  
GUIDE, ball  
1
1
210  
196967  
193027  
118504  
183185  
15E329  
183178  
Model 249059, 249057  
Model 248205, 277070, 257146  
WIPER, piston  
GLAND, female, piston  
V-PACKING, leather, piston  
GLAND, packing, male  
SLEEVE, cylinder  
1
1
1
3
1
1
216*  
217*  
218*  
219*  
220  
205  
248210  
257031  
107098  
Model 248205, 249057, 249059, 277070  
Model 257146  
PACKING, o-ring  
215  
214  
221*  
222  
2
ROD, piston  
212  
227  
248207  
249028  
183175  
15C990  
Model 248205, 277070  
Model 249059, 249057, 257146  
V-PACKING, leather, throat  
GLAND, female, throat  
PACKING, o-ring  
SPACER, nut  
WASHER, backup  
O-RING, fluoroelastomer (not used on  
249057, 249059, 257146)  
NIPPLE, straight  
Model 249057, 249059 (not shown)  
ADAPTER, 3/8 npt x 3/8 npsm  
Model 249057, 249059, 257146 (not  
shown)  
1
1
3
1
1
1
1
1
207  
221  
223*  
224*  
227*108526  
228  
229*  
230*  
C20987  
15C998  
118494  
213  
230  
220  
231  
232  
117608  
162485  
1
1
1
(Not an O-ring groove)  
ti23114a  
* These parts are also included in Repair Kit 248213, which may be  
purchased separately.  
† These parts are also included in Carbide Seat Kit 244199, which  
may be purchased separately.  
These parts are also included in Pump Repair Kit 249189, which  
may be purchased separately.  
310643U  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Parts - Pump 253056  
Parts - Pump 253056  
Ref.  
201*179810  
202 193046  
Part  
Description  
SEAL, throat  
NUT, packing  
V-PACKING, throat, V-Max,  
UHMWPE, blue  
Qty.  
1
1
3
201  
203*192692  
202  
228  
204*15C987  
GLAND, male, throat  
CYLINDER, pump  
BALL, check  
1
1
1
221  
222  
205  
287876  
206*  
105444* BALL, sst, 0.3125 in. (optional)  
119259BALL, ceramic, 0.3125 in. (standard)  
207*156593  
208*192693  
PACKING, o-ring  
V-PACKING, piston, V-MAX,  
UHMWPE, blue  
1
3
224  
210  
287877  
VALVE, piston  
SEAT, carbide  
HOUSING, intake  
BALL, check, inlet  
1
1
1
1
212† ^ 197470  
213  
214  
223  
287878  
102972*BALL, sst, 0.875 in. (optional)  
111453^ BALL, ceramic, 0.750 (standard)  
219  
203  
204  
215  
196967  
216*118503  
217*178969  
GUIDE, ball  
WIPER, piston  
GLAND, female, piston  
V-PACKING, leather, piston  
GLAND, male  
SLEEVE, cylinder  
O-RING, ptfe  
ROD, piston (Mark IV)  
V-PACKING, leather, throat  
GLAND, female  
PACKING, o-ring  
SPACER, throat, nut  
WASHER, backup  
SPACER, sleeve  
O-RING  
1
1
1
2
1
1
2
1
2
218  
219*196880  
220 248209  
221*108526  
222 249969  
178939  
218  
217  
208  
223*178940  
224*15C988  
227*† ^ 108526  
228*158776  
229*15C997  
216  
229  
1
1
1
1
1
206  
210  
230  
15G494  
231*107098  
* These parts are also included in Repair Kit with stainless steel  
ball,287825, which may be purchased separately.  
These parts are also included in Repair Kit with ceramic ball,  
24V063, which may be purchased separately.  
215  
† These parts are also included in Carbide Seat Kit with stainless  
steel ball, 244199, which may be purchased separately.  
^ These parts are also included in Carbide Seat Kit with ceramic ball,  
24V071, which may be purchased separately.  
205  
214  
227  
207  
221  
212  
213  
220  
(Not an O-ring groove)  
230  
231  
16  
310643U  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Technical Data  
Technical Data  
U.S.  
Metric  
227 bar, 22.7 MPa  
1-5/16-12 un(m)  
Maximum Working Pressure  
Fluid Inlet Size  
3300 psi  
1-5/16-12 un(m)  
Fluid Outlet Size  
248204, 255968, 277069  
248205, 249057, 249059,  
253056, 277070, 257146  
1/4 npt(f)  
3/8 npt(f)  
stainless steel, PTFE, leather, nylon, zinc-plated carbon steel, tungsten  
carbide, chrome plating, fluoroelastomer, acetal, polyethylene  
Wetted Parts  
310643U  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs  
will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT  
LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
For the latest information about Graco products, visit www.graco.com.  
For patent information, see www.graco.com/patents.  
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
Original instructions. This manual contains English. MM 310643  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA  
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revised U, April 2015  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 

Graco Baby Furniture 4622 User Manual
Hamilton Beach Slow Cooker 33351 User Manual
Hans Grohe Indoor Furnishings 10090XXX User Manual
Hasbro Games 06717 User Manual
Honeywell Thermostat CT8602 User Manual
Hotpoint Oven UE47 User Manual
Hotpoint Refrigerator RLS 175 x RLS 150 x RLFM 151 x RLFM 171 x User Manual
Huffy Fitness Equipment 7000MXP User Manual
Husqvarna Chainsaw CS 2512 User Manual
iLive MP3 Docking Station IS208B User Manual