Repair
Displacement Pump
310894G
- For portable spray application of architectural paints and coatings
or replacement pump for Graco GMaxt II sprayers -
3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure
Model 287512, Series A
GMax II 3900 Sprayer,
Rental Pro 360G
Model 287513, Series A
GMax II 5900 Sprayer,
UltraMax II 1095/1595 with ProConnect
Model 287579, Series A
GMax II 5900HD Sprayer
Model 249122, Series A
GMax II 7900 Sprayer,
Ultra Max II 1895
Model 287928, Series A
Mark Vt International
Model 287929, Series A
Mark V North America
Model 289590, Series A
TexSpray 7900HD,
Mark X, 230V, Domestic
ti6177a
Important Safety Instructions
Read all warnings and instructions in this manual
and in your sprayer manual. Save these
instructions.
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441
Copyright 2005, Graco Inc. is registered to I.S. EN ISO 9001
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Pressure Relief Procedure
Pump Repair Kits
Pump
Repair Kit
248212
248213
248213
249123
249189
248213
249123
WARNING
287512
287513
287579
249122
287928
287929
289590
PRESSURIZED EQUIPMENT HAZARD
The system pressure must be manually
relieved to prevent the system from
starting or spraying accidentally. To
reduce the risk of an injury from accidental spray
from the gun, splashing fluid, or moving parts,
follow the Pressure Relief Procedure whenever
you:
D are instructed to relieve the pressure,
D stop spraying,
D check or service any of the system equipment,
D or install or clean the spray nozzle.
Tools Needed
Vise
12 in. adjustable, open end wrench (2)
Hammer, 20 oz maximum
Small screwdriver
1. Lock gun trigger safety.
Throat Seal Liquid
Pick or long small screwdriver
2. Turn engine ON/OFF switch to OFF.
Cleaning and Inspecting Parts
3. Move pump switch to OFF and turn pressure
control knob fully counterclockwise.
1. Clean and inspect parts. Pay particular attention to
the ball seats in the intake valve and piston, which
must have no nicks or wear, and to the inside of
the sleeve and the outside of the piston rod, which
must not be worn or scratched. Replace worn or
damaged parts.
4. Unlock trigger safety. Hold metal part of gun firmly
to side of grounded metal pail, and trigger gun to
relieve pressure.
5. Lock gun trigger safety.
WARNING
COMPONENT RUPTURE HAZARD
Never use sharp or pointed tools to
remove sleeve or other components
6. Open pressure drain valve. Leave open until ready
to spray again.
which could result in pump rupture and
cause serious bodily injury. If the sleeve cannot be
removed easily, return the sleeve and cylinder to
your Graco distributor for removal.
If you suspect that the spray tip or hose is completely
clogged, or that pressure has not been fully relieved
after following the steps above, VERY SLOWLY loos-
en tip guard retaining nut or hose end coupling to re-
lieve pressure gradually, then loosen completely. Now
clear tip or hose.
2. Remove and clean the sleeve when you are
repacking the pump.
310894
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Disassembling the pump
Fig. 3. Disassemble intake valve. Clean and inspect.
O-ring (227) may require a pick for removal.
Fig. 1. Remove packing nut (202) and throat adjust-
ment spacer (228).
202
228
211
used on
249122,
289590
227
7570e
ti6178b
Fig. 3
Fig. 4. Tap piston rod out of cylinder with a hammer or
flip over and tap piston rod out against a bench.
Fig. 1
Note: Sleeve may come out
of cylinder with piston rod.
Fig. 2. Unscrew intake valve from cylinder.
ti6180a
Fig. 4
Fig. 5. Remove piston rod from sleeve, or remove
sleeve from cylinder.
ti6179a
Fig. 2
ti6181a
Fig. 5
4
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
WARNING
Not used
COMPONENT RUPTURE HAZARD
Do not clean or wipe the piston valve
threads. Cleaning the piston valve
on
287512
threads could destroy the special sealing
patch and cause the piston valve to come loose
during operation, causing pump bursting and
possible serious bodily injury.
Fig. 6. Unscrew piston valve from piston rod. Clean
and inspect parts. The piston has a special thread
locking/sealing patch. Do not remove the patch. The
patch allows four disassembly/assembly procedures
before it is necessary to apply Loctiter to the threads.
ti6182a
Fig. 8
Assembling the pump
Fig. 9. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Stack male gland
(204) on piston rod. Alternately stack UHMWPE (208)
and leather (218) packings (note orientation) on piston
rod. Install female gland (217). Install piston wiper
(216) (note orientation) and backup washer (229) on
piston valve (210). The special sealing patch on piston
valve threads is good for four repackings. Use Loctiter
on piston valve threads after four repackings.
Not
used on
287512
210
ti6183a
Fig. 6
229
216
Fig. 7. Remove packings and glands from piston rod.
Not
used on
287512
217
ti6185a
218 204 208
Note: pump 249122 and 289590 do not use
leather packings in piston stack. Alternately
stack blue (208) and brown (218) packings
on this pump.
ti6184a
Fig. 7
Fig. 8. Remove throat packings and glands from cylin-
der. Discard throat packings and glands.
Fig. 9
310894
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 10. Install ball (206) in piston rod. If Loctiter is ap-
plied to piston valve threads, ensure that none gets on
ball.
Fig. 12. Soak all leather packings in SAE 30W oil for 1
hour minimum prior to assembly. Place male gland
(204) in cylinder. Alternately stack UHMWPE (203) and
leather packings (223) (note orientation). Place female
gland (224) in top of cylinder. Seat packings.
224
Not
206
used on
287512
223
203
204
ti6186a
Fig. 10
ti6188a
Fig. 11. Tighten piston valve to piston rod as specified:
Fig. 12
Fig. 13. Install seal (201) into packing nut (202). Install
throat adjustment spacer (228) onto packing nut.
Loosely install packing nut into cylinder.
Torque to 27 +/--3 ft-lb
(36.61 +/-- 4.06 N• m)
(287512)
Torque to 55 +/--3 ft-lb
(74.57 +/-- 4.06 N• m)
(249122, 287513,
289590)
201
202
(228 o--ring
on 249122,
289590 )
228
ti6187a
ti6189a
Fig. 11
Fig. 13
6
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Note: O-ring (207) is not required for safe pump opera-
tion.
CAUTION
Never slide piston assembly (222) into top of
Fig. 15. Grease top inch or two of piston rod (222) that
goes through the sleeve/cylinder assembly throat
packings (205). Grease piston packings at bottom of
piston rod.
sleeve (220) as this may damage piston packings.
Fig. 14. Grease o-rings (221) and place inside
cylinder (205) and on sleeve (220). Slide sleeve (220)
into bottom of cylinder (205). Replace o-ring (207) if
desired.
Carefully slide piston assembly (222) into bottom of
sleeve/cylinder assembly (205) until pump rod pro-
trudes at the top and piston packings are totally inside
the sleeve (220).
Place inside cyl-
inder (205) and
push to shoulder
with sleeve (220).
205
205
207
220
207
222
221
ti6273a
ti6193a
Fig. 14
Fig. 15
310894
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Fig. 16. Reassemble intake valve with new o-ring
(227), seat (212) and ball (214). Seat may be flipped
over and used on other side. Clean seat thoroughly.
Fig. 18. Torque packing nut (202) down onto adjust-
ment spacer (228) 140 +/--10 in-lb (15.82 +/-- 1.13
N•m).
Remove throat adjustment spacer (228) when pump
packings begin to leak after much use. Then tighten
packing nut down until leakage stops or lessens. This
allows approximately 100 gallons of additional opera-
tion before a repacking is required.
211
used on
214
212
227
249122,
289590
202
(228 o--ring
on 249122,
228
289590)
ti6197a
Fig. 16
Fig. 17. Install intake valve on cylinder. If a wrench is
used torque as follows:
70 +/--5 ft-lb (94.91 +/-- 6.77 N•m) (Model 287512)
80 +/--5 ft--lb (108.5 +/-- 6.77 N•m)
(Model 287513, 287579 )
200 +/--15 ft--lb (271.2 +/-- 20.34 N•m)
(Model 249122, 289590 )
ti6195a
Fig. 18
If a wrench is not used, be sure intake valve is bot-
tomed out against cylinder.
ti6194a
Fig. 17
8
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Service
Cross Sectional Reference
222
201
Pump 287512
202
228
224
V-Maxt UHWMPE, blue
203
204
223
Leather
205
221
220
Pump 287512
206
207
V-Maxt UHWMPE,
brown on 249122,
289590
219
2
208
217
218
Leather
216
210
211
221
215
V-Maxt UHWMPE, blue
Only on
249122,
289590
229
214
213
212
227
ti6196a
Fig 19
Technical Data
Maximum working pressure . . . . . . . . . . . . . . . 3300 psi
(228 bar, 22.8 MPa)
Fluid outlet size . . . . . . . . . . . . . . . . . 3/8 npt(f)
Wetted parts . . . . . . . . . . . . . . . . . stainless steel, PTFE,
leather, nylon, zinc-plated carbon steel,
tungsten carbide, brass, fluoroelastomer,
acetal, polyethylene
Fluid inlet size . . . . . . . . . . . . . . . . . . . . . . 1-5/16 npt(m)
NOTE: LoctiteR is a Loctite Company registered
trademark.
310894
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 287512
Model 287512, Series A
Ref
No.
Part No. Description
Qty.
201
201
202
203* 192692
179810
193046
SEAL, throat
NUT, packing
1
1
3
221*
222
202
228
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
BALL, sst, 0.3125 in.
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
BALL, sst, 0.5000 in.
GUIDE, ball
204* 15C987
205
206* 105444
207* 114054
208* 192693
1
287551
224*
1
1
3
*223
219*
210
212† 239922
239932
1
1
203*
204*
218*
217*
*208
213
214*† 105445
215 192624
216* 118503
217* 178969
218* 178939
219* 196880
220
221* 108526
222 248206
223* 178940
224* 15C988
227*† 107079
15C785
1
1
1
1
1
2
1
1
2
1
2
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
O-RING, PTFE
ROD, piston
V-PACKING, leather, throat
GLAND, female
216*
229
248209
206*
210
215
PACKING, o-ring
1
1
1
1
1
1
228
192714
SPACER, throat, nut
WASHER, backup
FITTING, pump (not shown)
O-RING, acetal
229* 15C997
230†† 15E802
231
205
118494
†*214
†*227
213
232†† 15E807
TUBE, intake (not shown)
207*
221*
212†
*
These parts are also included in Repair Kit 248212,
which may be purchased separately.
†
These parts are also included in Carbide Seat Kit
239922, which may be purchased separately.
†† These parts are included with pump 287512.
220
231
ti5491a
10
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 287513
Model 287513, Series A
Ref
No.
Part No. Description
Qty.
201
201
202
203* 193124
183171
193032
PLUG
NUT, packing
1
1
4
202
228
221*
222
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
BALL, sst, 0.3125 in.
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
BALL, metallic
204* 15C989
205
206* 101947
207* 106556
208* 193125
1
287552
224*
1
1
4
*203
219*
210
212† 244199
240150
1
1
223*
204*
213
214*† 102972
215 193027
216* 118504
217* 183185
218* 15E329
219* 183178
220
221* 107098
222 248207
223* 183175
224* 15C990
227*† 108526
15E654
1
1
1
1
1
3
1
1
2
1
3
1
1
1
1
1
1
1
*218
208*
217*
GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
PACKING, o--ring
ROD, piston
V-PACKING, leather, throat
GLAND, packing
PACKING, o-ring
216*
229
248210
206*
210
215
228
193127
SPACER, nut
229* 15C998
230†† 15E802
231
WASHER, backup
FITTING, pump (not shown)
O-RING, acetal
205
118494
232†† 15E806
TUBE, intake (not shown)
207*
221*
†*214
†*227
*
These parts are also included in Repair Kit 248213,
which may be purchased separately.
212†
213
†
These parts are also included in Carbide Seat Kit
244199, which may be purchased separately.
†† These parts are included with pump 287513.
220
231
ti5490a
310894
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 249122
Model 249122, Series A;
Ref
No.
221*
222
Part No.
Description
Qty.
201
202
203* 193722
112590
15E962
PLUG
NUT, packing
V-PACKING
V-Maxt UHMWPE, blue
GLAND, packing, male, throat
CYLINDER, pump
BALL, valve, check
PACKING, o-ring
1
1
8
201
204* 198768
205
206* 107203
207* 107306
210
211
1
1
1
1
1
1
1
249139
202
228
219*
218*
249177
233698
VALVE, piston
SPRING, intake ball
KIT, SEAT, carbide
includes 214 and 227
HOUSING, intake (foot)
BALL, sst
*203
224*
212† 240918
*223
213
214*† 107167
215 198505
216* 119636
217* 189588
218* 15E639
15E655
1
1
1
1
1
3
217*
216*
GUIDE, ball
WIPER, piston
203*
204*
GLAND, packing, female
V-PACKING, piston, V-Maxt
UHMWPE, brown
GLAND, packing, male
SLEEVE, cylinder
PACKING, o-ring
229
206*
210
219* 189585
1
1
2
1
3
1
1
1
1
1
1
1
220
221* 108822
222 249119
223* 112591
224* 194175
227*† 107098
249121
211
215
ROD, piston
V-PACKING, leather, throat
GLAND, packing, female
PACKING, o-ring
†*214
†*227
205
228
108832
SPACER, nut
229* 15F183
230†† 15E802
231
WASHER, backup
FITTING, pump (not shown)
O-RING, acetal
212†
213
118494
232†† 15E806
TUBE, intake (not shown)
*
These parts are also included in Repair Kit 249123,
which may be purchased separately.
207*
221*
†
These parts are also included in Carbide Seat Kit
240918, which may be purchased separately.
†† These parts are included with pump 249122.
231
220
ti5673a
12
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 287579
Model 287579, Series A
Ref
No.
Part No. Description
Qty.
201
201
202
203* 193124
183171
193032
PLUG
NUT, packing
1
1
4
202
228
221*
222
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
BALL, bearing
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
BALL, metallic
204* 15C989
205
206* 101947
207* 106556
208* 193125
1
287581
224*
1
1
4
*203
219*
210
212† 244199
240150
1
1
223*
204*
213
214*† 102972
215 196967
216* 118504
217* 183185
218* 15E329
219* 183178
220
221* 107098
222 249028
223* 183175
224* 15C990
227*† 108526
196753
1
1
1
1
1
3
1
1
2
1
3
1
1
1
1
1
*218
208*
217*
GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
PACKING, o--ring
ROD, piston
V-PACKING, leather, throat
GLAND, packing
PACKING, o-ring
SPACER, nut
WASHER, backup
FITTING, pump (not shown)
216*
229*
206*
248210
210
215
228
193127
229* 15C998
230†† 15E802
205
*
These parts are also included in Repair Kit 248213,
which may be purchased separately.
207*
221*
†*214
†*227
212†
213
†
These parts are also included in Carbide Seat Kit
244199, which may be purchased separately.
†† These parts are included with pump 287579.
220
ti6277a
310894
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 287928
Model 287928, Series A
Ref
No.
Part No. Description
Qty.
201
201
202
203* 193124
183171
193032
PLUG
NUT, packing
1
1
4
202
228
221*
222
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
BALL, ceramic
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
BALL, ceramic
204* 15C989
205
206* 116327
207* 106556
208* 193125
1
287581
224*
1
1
4
*203
219*
210
212† 244571
240150
1
1
223*
204*
213
214*† 111453
215 196967
216* 118504
217* 183185
218* 15E329
219* 183178
220
221* 107098
222 249028
223* 183175
224* 15C990
227*† 108526
196753
1
1
1
1
1
3
1
1
2
1
3
1
1
1
1
1
*218
208*
217*
GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
PACKING, o--ring
ROD, piston
V-PACKING, leather, throat
GLAND, packing
PACKING, o-ring
SPACER, nut
216*
229*
206*
248210
210
215
228
193127
229* 15C998
230†† 15G880 FITTING, pump (not shown)
WASHER, backup
205
*
These parts are also included in Repair Kit 249189,
which may be purchased separately.
207*
221*
†*214
†*227
212†
213
†
These parts are also included in Carbide Seat Kit
244571, which may be purchased separately.
†† These parts are included with pump 287928.
220
ti6277a
14
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 287929
Model 287929, Series A
Ref
No.
Part No. Description
Qty.
201
201
202
203* 193124
183171
193032
PLUG
NUT, packing
1
1
4
202
228
221*
222
V-PACKING, throat,
V-Maxt UHMWPE, blue
GLAND, male, throat
CYLINDER, pump
BALL, bearing
PACKING, o-ring
V-PACKING, piston
V-Maxt UHMWPE, blue
VALVE, piston
KIT, seat, carbide
includes 214 and 227
VALVE, intake (foot)
BALL, metallic
204* 15C989
205
206* 101947
207* 106556
208* 193125
1
287581
224*
1
1
4
*203
219*
210
212† 244199
240150
1
1
223*
204*
213
214*† 102972
215 196967
216* 118504
217* 183185
218* 15E329
219* 183178
220
221* 107098
222 249028
223* 183175
224* 15C990
227*† 108526
196753
1
1
1
1
1
3
1
1
2
1
3
1
1
1
1
1
*218
208*
217*
GUIDE, ball
WIPER, piston
GLAND, female, piston
V-PACKING, leather, piston
GLAND, male
SLEEVE, cylinder
PACKING, o--ring
ROD, piston
V-PACKING, leather, throat
GLAND, packing
PACKING, o-ring
SPACER, nut
216*
229*
206*
248210
210
215
228
193127
229* 15C998
230†† 15G880 FITTING, pump (not shown)
WASHER, backup
205
*
These parts are also included in Repair Kit 248213,
which may be purchased separately.
207*
221*
†*214
†*227
212†
213
†
These parts are also included in Carbide Seat Kit
244199, which may be purchased separately.
†† These parts are included with pump 287929.
220
ti6277a
310894
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts -- Pump 289590
Model 289590, Series A;
Ref
No.
221*
222
Part No.
Description
Qty.
201
202
203* 193722
112590
15E962
PLUG
NUT, packing
V-PACKING
V-Maxt UHMWPE, blue
GLAND, packing, male, throat
1
1
8
201
204* 198768
205
206* 107203
207* 107306
210
211
1
1
1
1
1
1
1
15G437 CYLINDER, pump
202
228
219*
218*
BALL, valve, check
PACKING, o-ring
VALVE, piston
SPRING, intake ball
KIT, SEAT, carbide
includes 214 and 227
HOUSING, intake (foot)
BALL, sst
249177
233698
*203
224*
212† 240918
*223
213
214*† 107167
215 193391
216* 119636
217* 189588
218* 15E639
15A303
1
1
1
1
1
3
217*
216*
GUIDE, ball
WIPER, piston
203*
204*
GLAND, packing, female
V-PACKING, piston, V-Maxt
UHMWPE, brown
GLAND, packing, male
SLEEVE, cylinder
PACKING, o-ring
229
206*
210
219* 189585
1
1
2
1
3
1
1
1
1
1
1
220
221* 108822
222 288103
223* 112591
224* 194175
227*† 107098
228
229* 15J800
230†† 15G509 FITTING, pump (not shown)
232†† C20195 PACKING, o-ring (not shown)
249121
211
215
ROD, piston
V-PACKING, leather, throat
GLAND, packing, female
PACKING, o-ring
PACKING, o-ring
WASHER, backup
†*214
†*227
205
108832
212†
213
*
These parts are also included in Repair Kit 249123,
which may be purchased separately.
207*
221*
†
These parts are also included in Carbide Seat Kit
240918, which may be purchased separately.
†† These parts are included with pump 289590.
220
ti5673a
16
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
310894
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from
defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended,
or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the
equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained
in accordance with Graco’s written recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by
faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or sub-
stitution of non--Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of
Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture,
installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for
verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The
equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does notdisclose anydefect
in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and
transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT
NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other
remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any
other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the
date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD
BUT NOT MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches,
hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in mak-
ing any claim for breach of these warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment
hereunder, or the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract,
breach of warranty, the negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings
entered into, given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnais-
sent avoir convenu que la rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires
exécutés, donnés ou intentés à la suite de ou en rapport, directement ou indirectement, avec les procedures concernées.
Graco Phone Number
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1--800--690--2894 Toll Free
All written and visual data contained in this document reflect the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English GN 310894 MM 310894
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440--1441
2/2005, Rev 03/2008
18
310894
Download from Www.Somanuals.com. All Manuals Search And Download.
|