24962
Universal Remote
Instruction Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Battery Installation
1. On the back of the remote, push down on the
tab and lift the cover off.
2. Match the batteries to the + and - marks inside
the battery case, then insert 2 AAA Alkaline
batteries.
3. Press the battery cover back into place.
Battery Saver
Your remote automatically turns off if the buttons
are depressed more than 30 seconds. This will
save your batteries should your remote get stuck in
a place where the buttons remain depressed (e.g.,
between the sofa cushions).
Code Saver
You will have up to 10 minutes to change the
batteries in your remote without losing codes you
have programmed. However, do not press any
buttons until batteries are installed in the remote.
If buttons are pressed without batteries in the
remote, all codes will be lost.
Code Setup
The SETUP button is used to setup the remote.
You can either setup the remote using the code
for your brand of product, from the code tables (on
separate sheet), or you can search through the
library of codes until you find a code that works for
your product. Please refer to “Code Search” page
8 for more information on using the code search
feature to learn how to search through the library
of codes for your products. NOTE: You can store
any kind of code under any mode (except TV). I.e.,
you can store a DVR code under the SAT/CBL
button, or a cable code under the DVD button, etc.
However, you can only store TV codes under the
TV button.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.g., PREV. CH may be called RECALL,
or ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.g., your product must have PREV. CH ability
for the PREV. CH button to operate this feature.
TV, DVD, SAT/CBL Selects
product to be operated.
SETUP For setup.
SHIFT Accesses
shifted functions.
MUTE Turns off the
TV sound while the
picture remains.
OK Selects menu
items for the device
you are controlling.
INFO button brings up
DVD Display or Control
Menu for Chapter/
Track/Title number,
Time remaining/elapsed
indication, system
information, etc.
MENU
Selects the on-screen
menu.
DOT Used to
select digital chan-
nels, e.g., 2.3.
RECORD, PLAY, STOP,
REW, FF, PAUSE oper-
ate your DVD or DVR
even when the remote
is set to operate the TV.
Also operates DVD/DVR
Scan -/+.
Download from Www.Somanuals.com. All Manuals Search And Download.
Button Functions, cont.
Red Indicator
ON-OFF Turns
Lights when any
button is pressed.
device On or Off.
INPUT
For some TVs, press
repeatedly to select
from available viewing
sources (antenna, cable
box, DVD, etc.).
CHANNEL Up/Down
Changes the channels.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
PREV. CH Returns to
the previously
selected channel.
EXIT Exit On-Screen
Menus and/or Return
to previous On
Screen selection.
NUMBERS
Enter numbers for direct
channel selection. Some
products require ENTER
to be pressed after
channel selection.
ENTER
For some TV models,
used after direct
channel number
entry to immediately
change to the
selected channel.
Note: The REC button must be pressed TWICE to record
from your DVR. For some brands of DVRs, you might
need to press the REC button once, then press it again
for three seconds.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SHIFT Function
Press SHIFT (Setup) prior to the shifted key func-
tion, e.g., for MENU - press and release SHIFT
(Setup) then MENU (Info).
UP - press and release SHIFT then UP (Chan+).
DOWN - press and release SHIFT then DOWN
(Chan-).
LEFT - press and release SHIFT then LEFT (Vol-).
RIGHT - press and release SHIFT then RIGHT
(Vol+).
OK - press and release SHIFT then OK (Mute).
EXIT - press and release SHIFT then EXIT (Prev.
Ch).
The red indicator blinks for each key press.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Direct Code Entry
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
2. Press and release the desired mode
button (TV, DVD, etc.). The red indicator
blinks, then stays lit.
3. Enter the 4-digit code
from the code tables
(on separate sheet).
Note: after a valid code
entry, the red indicator
turns off. For an invalid
code, the red indicator
flashes.
4. With your device on, press ON/
OFF. If the device turns off, no
further programming is required.
Note: If some buttons do not
operate your equipment, try one
of the other codes for your brand.
Write your codes down here for easy reference
later.
Device
Device stored Code
TV
TV
DVD
SAT/CBL
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Search
If your device does not respond after you have
tried all the codes for your brand, or if your brand is
not listed, try searching for your code by following
these steps.
1. Manually turn on the device (TV, DVD, etc.) to
be controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
3. Press and quickly release the desired
mode button (TV, DVD, etc.). The red
indicator blinks off once.
4. Press the CHAN+ button
repeatedly (up to 300 times)
until the device to be controlled
changes channel. The red
indicator blinks off with each
button press. If you accidentally overshoot
the code required, press the CHAN- button to
backtrack through the library until the device
changes channel. Pressing CHAN+ changes
direction to forward again.
5. Press and release ENTER to install the
code.
Most users will store DVD codes under the DVD button,
and Satellite or Cable codes under SAT/CBL. If (for ex-
ample) you want to store a DVR code under SAT/CBL,
first follow the procedure for Direct Code Entry (page
8) and press SAT/CBL in step 2 of Direct Code Entry,
then enter ANY DVR code in step 3 of Direct Code Entry.
Then follow the steps above for Code Search.
Note: If the device does not have a CHAN+ button, use
PLAY (DVD/DVR/VCR only) or POWER instead. Code
Search starts from the currently stored 4 digit number
under that mode. Sometimes the first code that “works”
with your device may only allow limited functionality
(e.g., the MENU button might not work). There may be
a code that performs more functions. Continue the code
search process until the best code is found.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Code Identification
The Code Identification Feature allows you to
identify the 4-digit library code stored under your
device key. For example, if you want to find out
what 4-digit code is stored under your TV device
key, follow the six steps below:
1. Press and hold the SETUP button until
the red indicator stays on. Release the
SETUP button.
2. Press and release the desired mode
button (TV, DVD, etc.). The red
indicator blinks, then stays lit.
3. Press and release the SETUP button.
The red indicator blinks once and
remains lit.
4. To find the first digit for
the code stored under
the mode key pressed
in step 2, press each
numeric key from 0-9 in
turn. The number that
causes the indicator
light to blink is the first
digit in your code.
5. To find the second digit, repeat step 4.
6. Repeat step 4 again to find the third and fourth
digits. This time the red indicator turns off and
stays off.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote
Controlling Devices with Separate
Power On and Off Buttons
Some GE, RCA and ProScan models require
you to press the device button for more than one
second to turn the device on and the POWER
button to turn the device off.
Controlling Combo Devices
Some Combo devices (e.g., TV/DVR, TV/DVD,
DVD/DVR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/
DVD Combo, you might need to set up one code
under the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
DVR/DVD Punch-Through
This remote allows the 6 DVD/VCR transport
buttons (i.e. PLAY, PAUSE, STOP, FF, REWIND,
and REC) to Punch-through from any Mode
programmed with TV, SAT or Cable codes to the
last DVD, or VCR programmed Mode you used,
i.e., the transport keys control your DVD or VCR
player even when you are in TV, SAT or Cable
mode. If you use a SAT/DVR, Cable/DVR, etc., you
may want to disable this Punch-through feature
to allow the transport keys to control your DVR
device. The following steps will disable the punch-
through feature:
1. Press and hold SETUP until the red indicator
stays on, then release the SETUP button.
2. Press and hold PAUSE until the red indicator
turns off, then release the PAUSE button. The
PAUSE button needs to be held held for about
3 seconds before the red indicator turns off.
The punch-through feature can be enabled again
by repeating the above steps.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Remote, cont.
Volume/Mute Control and Punch-
Through
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own
then those buttons will punch-through control to
the TV Mode device without needing to change to
TV Mode.
Setting ALL Volume/Mute Control to
any one Mode
This routine can set all Modes to “punch-through”
to any one chosen Mode for Volume/Mute button
control without the needing to change to that
Mode.
1. Press and hold the SETUP button until
the red indicator turns on, then release
the button.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
3. Press and release the desired Mode button
(TV, DVD, etc.) for Volume/Mute control,
the red indicator blinks then stays on.
4. Press and release the MUTE button
and the red indicator turns off. The
red indicator will blink rapidly for
three seconds if the Mode you have
selected has no Volume/Mute control.
All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
Download from Www.Somanuals.co1m1. All Manuals Search And Download.
Using Your Remote, cont.
Setting any Mode to use its own
Volume/Mute Control
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode
has no Volume/Mute functions of its own then the
Volume/Mute buttons will do nothing.
1. Press and hold the SETUP button until
the red indicator turns on, then release
the button.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
3. Press and release the desired Mode
button (TV, DVD, etc.), the red indicator
blinks then stays on.
4. Press and release the VOL- button,
the red indicator blinks then stays on.
5. Press and release the MUTE button and
the red indicator turns off.
Your chosen Mode will now use its own Volume/
Mute control.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Remote does not operate your product.
•
Press the mode button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some
features of your product.
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
•
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Red Indicator blinks after you program
a product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
Lost Your Codes?
Enclosed with this remote is a sticker on which
you should write the codes for each device you
programmed. Apply the sticker to the back of
the remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
13
Download from Www.Somanuals.com. All Manuals Search And Download.
90 Day Limited Warranty
Jasco Products Company warrants this product
to be free from manufacturing defects for a period
of ninety days from the original date of consumer
purchase. This warranty is limited to the repair
or replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit.
This warranty is in lieu of all other warranties
express or implied. Some states do not allow
limitations on how long an implied warranty lasts
or permit the exclusion or limitation of incidental or
consequential damages, so the above limitations
may not apply to you. This warranty gives you
specific rights, and you may also have other rights
which vary from state to state. If unit should prove
defective within the warranty period, return prepaid
with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114-2205
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
24962
Universal Remote
Instruction Manual
Jasco Products Company
10 E. Memorial Road
Oklahoma City, OK 73114-2205
Made in China
24962-03/10
Download from Www.Somanuals.com. All Manuals Search And Download.
|