P3PC-E177-03EN
fi-4860C Image Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
The contents of the Operator’s Guide is as follows:
1. BASIC SCANNER OPERATIONS
This chapter describes basic scanner operations including basic
document scanning.
2. SCANNING VARIOUS TYPES OF DOCUMENTS
This chapter describes how to scan various type of documents.
3. DAILY CARE
This chapter describes how to clean the scanner.
4. REPLACEMENT OF CONSUMABLES
This chapter describes how to replace scanner consumables.
5. SOLVING COMMON PROBLEMS
This chapter describes how to remedy document jams, other troubles,
items to check before contacting the agent where you bought the
scanner, and how to check device labels.
6. ADF DOCUMENT SPECIFICATIONS
This chapter describes the types of documents which can be scanned
with this scanner.
7. OPERATOR PANEL MENUS
This chapter describes Setup-mode and Test-mode.
8. OPTIONS
This chapter describes options.
9. SCANNER SPECIFICATIONS
This chapter lists the scanner specifications.
We hope that this manual is useful in taking full advantage of the fi-4860C
Duplex Color Scanner's capabilities.
●ii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Regulatory Information
FCC declaration
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
CAUTION
•
•
The use of a shielded interface cable is required to
comply with the Class A limits of Part 15 of FCC
rules. The length of the SCSI interface cable must
be 1.5 meters (5 feet) or less.
ATTENTION
The length of the AC cable must be 3 meters (10
feet) or less.
Canadian DOC Regulations
This digital apparatus does not exceed the Class A limit for radio noise emissions
from digital apparatus set out in the Radio interference Regulations of the Canadian
Department of Communications.
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescridtes dans le
Réglesment sur le brouillage radioélectrique dicté par le ministere des
Communications du Canada.
Cet appareil numérique de la classe A est conformme à la norme NMB-003 du
Canada.
●iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Bescheimigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/dieldas
•fi-4860C in Übereinsstimmung mit den Bestimmungen der
•AmtsblVfg 243/1991 funkentstört ist. Der Deutschen Bundesport wurde das
Inverkehrbringen dieses Gerätes angezeigt und die Berechtigung zur Überprüfung
der Serie auf Einhaltung der Bestimmungen eingeräumt.
•Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991:Der höchste
Schalldruckpegel beträgt 70 dB (A) order weniger gemäß ISO/7779.
●iv
Download from Www.Somanuals.com. All Manuals Search And Download.
International ENERGY STAR® Program
As an ENERGY STAR® Partner, PFU LIMITED has determined
that this product meets the ENERGY STAR® guidelines for energy
efficiency.
The International ENERGY STAR® Office Equipment Program is
an international program that promotes energy saving through the penetration of
energy efficient computers and other office equipment. The program backs the
development and dissemination of products with functions that effectively reduce
energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, facsimiles, copiers, scanners, and multifunction
devices. Their standards and logos (
nations.
) are uniform among participating
This product meet the ENERGY STAR® guidelines of Japan and U.S.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be
used in office, personal, domestic, regular industrial, and general-purpose
applications. It has not been designed and manufactured for use in applications
(simply called "high-safety applications" from here on) that directly involve serious
danger to life and health when an extremely high degree of safety is required, for
example, in the control of nuclear reactions at nuclear power facilities, automatic
flight control of aircraft, air traffic control, operation control in mass-transport
systems, medical equipment for sustaining life, and missile firing control in weapons
systems, and when provisionally the safety in question is not ensured. The user
should use this product without adopting measures for ensuring safety in such high-
safety applications. PFU LIMITED assumes no liability whatsoever for damages
arising from use of this product by the user in high-safety applications, and for any
claims or compensation for damages by the user or a third party.
●v
Download from Www.Somanuals.com. All Manuals Search And Download.
About the use of mercury
The scanner lamp contains mercury.
Too avoid unexpected injury, read the followings carefully.
Doing following actions may result in serious personal injuries:
•Do not put the substance in the lamp in your mouth as it contains mercury.
•Do not incinerate, crush, or shred the scanner.
•Do not breath the chemical liquid contained in the scanner parts.
Disposing of the scanner should be conducted as required by local ordinances or
regulations.
Illegal Copying
Reproducing bills, coins, government securities and passports, licenses issued by
public author or civilian organizations, official documents, private paper is illegal
and brought to justice
Copyrighted Material
Literary works like books, paintings, wood block prints, maps, drawings, and
photographs should not be reproduced other than the personal or domestic use or
the use within other limit without the rightful person’s permission.
●vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Trademarks
Microsoft, Windows and Windows NT are registered trademarks of Microsoft
Corporation of the USA and other respective countries.
ISIS is a registered trademark of Pixel Translations, A Division of Actionpoint Inc.
Adobe and the Adobe logo as well as Acrobat and the Acrobat Logo are trademarks
of Adobe Systems Incorporated.
Other product names referred to in this manual are registered trademarks or
trademarks of respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as follows:
®
®
®
Windows 95:
Refers to Microsoft Windows 95 operating system.
®
®
®
Windows 98:
Refers to Microsoft Windows 98 operating system.
®
®
®
Windows Me: Refers to Refers to Microsoft Windows Millennium Edition
operating system.
®
®
®
Windows 2000: Refers to Microsoft Windows 2000 Professional operating
system.
®
®
®
Windows XP: Refers to Microsoft Windows XP Professional operating
®
®
system, and Microsoft Windows XP Home Edition operating
system.
®
®
®
Windows NT : Refers to Microsoft Windows NT operating system Version4.0.
Where there is no distinction between the different versions of the above operating
system, the general term "Windows " is used.
All Rights Reserved, Copyright© PFU LIMITED 2002-2003.
●vii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
IF NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO
USERS OR BYSTANDERS.
While all efforts have been made to ensure the accuracy of all information in this
manual, PFU LIMITED assumes no liability to any party for any damage caused by
errors or omissions or by statements of any kind in this manual, its updates or
supplements, whether such errors are omissions or statements resulting from
negligence, accidents, or any other cause. PFU LIMITED further assumes no
liability arising from the application or use of any product or system described
herein; nor any liability for incidental or consequential damages arising from the use
of this manual. PFU LIMITED disclaims all warranties regarding the information
contained herein, whether expressed, implied, or statutory.
PFU LIMITED reserves the right to make changes to any products herein, to
improve reliability, function, or design, without further notice and without obligation.
●viii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Preface
Safety Precautions
This manual describes important details for ensuring the safe and correct use of
this product. Thoroughly read this manual before you start to use this product. In
particular, be sure to read and fully understand the Safety Precautions described in
this manual before you use this product.
Also, store this manual in a safe place so that it can be easily referred to during use
of this product.
Warning Indications Used In This Manual
This manual uses the following indications to ensure safe and correct use of this
product, and to prevent possible danger and injury to the operator and other
persons.
This indication alerts operators to an operation that, if not
strictly observed, may result in severe injury or death.
CAUTION
This indication alerts operators to an operation that, if not
strictly observed, may result in safety hazards to personnel or
damage to equipment.
WARNING
●ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Symbols Used In This Manual
This manual uses the following symbols in explanations in addition to warning
indications.
This symbol alerts operators to particularly important informa-
ATTENTION
tion. Be sure to read this information.
This symbol alerts operators to helpful advice regarding oper-
ation.
HINT
A TRIANGLE symbol indicates that special care and attention
is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users
are not allowed to do.
The drawing inside or under the circle shows the specific action
that is not allowed.
Outline characters on a colored background shows instructions
users should follow.
R
It may include the drawing which shows the sepecific instruc-
tion.
●x
Download from Www.Somanuals.com. All Manuals Search And Download.
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the
interest of product improvement.
If the actual displayed screen differs from the screen examples in this manual,
operate by following the actual displayed screen referring to the User's Manual of
the scanner application you are using.
Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32
scanner driver and the Image Capturing Software Utilities "ScandAll 21" for
®
®
Microsoft Windows .
●xi
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Safety Precautions
WARNING
The following describes important warnings described in this manual.
Do not touch the AC cable with wet hands.
Do not insert or disconnect the power plug with wet hands. Doing so might
cause electric shock.
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock.
Do not place heavy objects on AC cables, or pull, bend, twist, heat,
damage or modify AC cables.
Also, do not use damaged AC cables or power plugs, and AC cables or
power plugs when the wall socket is loose.
Use only specified AC cables and connector cables
Use only specified AC cables and connector cables. Failure to use the
correct cables might cause electric shock and equipment failure.
●xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Use this scanner only at the indicated power voltage. Do not connect
to multiple-power strips.
Use this scanner only at the indicated power voltage and current.
Improper power voltage and current might cause fire or electric shock.
Also, do not connect to multiple-power strips.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with
a soft, dry cloth. Accumulated dust might cause fire or electric shock.
Do not install in locations subject to oil smoke, steam, humidity, and
dust.
Do not install the scanner in locations subject to oil smoke, steam,
humidity, and dust. Doing so might cause a fire or electric shock.
Do not use the scanner if you smell strange odor.
If you sense heat coming from the device or detect other problems such
as smoke, strange smells or strange noises, immediately turn off the
scanner and then disconnect its power plug.
Make sure that the smoke has stopped, and then contact the agent where
you bought the scanner.
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn off the scanner and unplug
the power cable before contacting a Fujitsu certified repair agent.
●xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner.
Do not scan wet documents or document with paper clips or staples.
Do not splash or allow the scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the
scanner, immediately turn off the scanner and disconnect the power plug
from the power outlet.
Then contact the agent where you bought the scanner or Maintenance
Service Center.
Pay particular attention to this warning in households where there are
small children.
●xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner
contains high-voltage components. Touching these components might
cause fire or electric shock.
CAUTION
The following describes important cautions described in this manual.
Do not install the scanner on unstable surfaces.
Install the scanner on a desk so that none of its parts protrude outside of
the desktop. Also, make sure that the scanner is installed on a flat, level
surface.
Do not install the scanner on unstable surfaces. Install the scanner on a
level surface that is free of vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the
scsanner and other devices needed.
Firmly insert the power plug.
Firmly insert the power plug into the power outlet as far it can go.
●xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates
heat inside of scanner, that may results in fire or scanner failure.
Do not place heavy objects or climb on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's top
surface for performing other work. Improper installation might cause
injuries.
Before moving the scanner, disconnect the power plug from the power
outlet.
Do not move the scanner with the power and interface cables connected
as this might damage the cables, causing fire, electric shock or injuries.
Before moving the scanner, be sure to disconnect the power plug from the
power outlet, and disconnect data cables. Also, make sure that the floor is
free of obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of
electronic noise. Also, protect the scanner from static electricity as this
might cause the scanner to malfunction.
●xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt
and dust to enter the scanner, resulting scanner failure and malfunction.
Avoid any contact when scanner is in use.
Avoid any contact when scanner is operating as this may cause injuries.
Disconnect the power plug from the power outlet when the scanner is
not used for a long period of time.
When the scanner is not used for a long period of time, be sure to
disconnect the power plug from the power outlet for safety.
Do not install the scanner in the direct sunlight.
Do not install the scanner in the direct sunlight or near heating apparatus.
Doing so might cause excessive heat to build up inside the scanner,
causing fire or scanner trouble. Install the scanner in a well-ventilated
location.
Do not carry alone.
When moving the scanner, never carry alone. It is heavy.
●xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Fujitsu Group Offices
Please send your comments on this manual or on Fujitsu products to the following
addresses:
FUJITSU COMPUTER PRODUCTS OF
AMERICA, INC.
FUJITSU CANADA, INC.
2800 Matheson Boulevard East, Missis-
2904 Orchard Parkway, San Jose, CA 95134- sauga, Ontario L4W 4X5, Canada
2009, U.S.A.
Phone: (1-800)591-5924;
(1-408)432-6333
Technical Assistance Center:
(1-800)626-4686
Phone: (1-905)602-5454
Fax: (1-905)602-5457
E-mail: [email protected]
(For Sales Questions)
Fax: (1-408)894-1709
E-mail: [email protected]
(For technical questions)
FUJITSU EUROPE LTD.
FUJITSU DEUTSCHLAND GMBH.
Frankfurter Ring 211, 80807 München 40,
Germany
Hayes Park Central, Hayes End Road,
Hayes Middlesex UB4 8FE, U.K.
Phone: (44-208)573-4444
Phone: (49-89)323-78-0
Fax: (44-208)573-2643
Fax: (49-89)323-78-100
E-mail: [email protected]
E-mail: [email protected]
FUJITSU ITALIA S.p.A.
Via Nazario Sauro, 38
20099 Sesto San Giovanni (Milan), Italy
Phone: (39-02)26294-1
FUJITSU ICL ESPAÑA, S.A.
Camino Cerro de los Gamos, 1 28224,
Pozuelo de Alarcon, Madrid, Spain
Phone: (34-91)784-9000
Fax: (39-02)26294-201
Fax: (34-91)784-9379
E-mail: [email protected]
FUJITSU AUSTRALIA LTD.
Fujitsu House 2 Julius Avenue
North Ryde, N.S.W 2113 Australia
Phone: (61-2)9776-4555
FUJITSU ASIA PTE.LTD.
20 Science Park Road, #03-01, Tele Teck
Park Singapore Science Park II, Sin-
gapore 117674
Phone: (65)777-6577
Fax: (61-2)9776-4019
Fax: (65)771-5499
E-mail: [email protected]
●xviii
Download from Www.Somanuals.com. All Manuals Search And Download.
FUJITSU TAIWAN LTD.
19th Fl., No39, Sec.1,Chung-hwa Rd.,
Taipei, Taiwan
Phone: (886-2)2311-2255
Fax: (886-2)2311-2277
FUJITSU HONG KONG LTD.
10/F., Lincoln House, 979 King's Road,
Taikoo Place, Island East, Hong Kong
Phone: (852)2827-5780
Fax: (852)2827-4724
E-mail: [email protected]
FUJITSU SYSTEMS BUSINESS
(THAILAND) LTD.
12th Fl., Olympia Thai Tower, 444 Rach-
adapisek Road, Samsennok,
Huay kwang, Bangkok 10320, Thailand
Phone: (662)512-6066
FUJITSU KOREA LTD.
Susong Tower Building, 83-1
Susong-Dong, Jongno-Gu, Seoul, Korea,
150-010
Phone: (82-2)3787-6159
Fax: (82-2)3787-6164
Fax: (662)512-6068
E-mail: [email protected]
FUJITSU MALAYSIA SDN.BHD.
FUJITSU PHILIPPINES, INC
7th FL., Wisma Damansara, Jalan
2nd Fl., United Life Building, Pasay Road,
Semantan 50490 Kuala Lumpur, MALAY- Legaspi Village Makati,
SIA
Metro Manila, Philippines
Phone: (63-2)812-4002
Fax: (63-2)817-7576
Phone: (60-3)254-3644
Fax: (60-3)253-3940
Imaging Products Division,
PFU LIMITED
PFU LIMITED
(Corporate headquarters)
Solid Square East Tower, 580 Horikawa-
Nu 98-2 Unoke, Unoke-machi,
cho, Saiwai-ku, Kawasaki-shi, Kanagawa kahoku-gun, Ishikawa 929-1192, Japan
212-8563, Japan
Phone: (81-44)540-4658
Fax: (81-44)540-4639
Phone: (81-76)283-1212
Fax: (81-76)283-4689
Website:
E-mail: [email protected]
●xix
Download from Www.Somanuals.com. All Manuals Search And Download.
●xx
Download from Www.Somanuals.com. All Manuals Search And Download.
●xxii
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Checking the Contents of the
Scanner Package
When you unpack the scanner package, make sure that all the following parts are
included in the package. If any parts are missing or defective, contact to the distributer
where you purchased the scanner from.
Please handle the scanner and the accessories with care.
Scanner and Accessories
ꢁScanner
ꢁPower cable (x1)
ꢁUser Manual
(CD-ROM)
®
®
ꢁFUJITSU TWAIN32 ꢁFUJITSU ISIS driver
Scanner driver (CD-ROM) (CD-ROM)
ꢁAdobe Acrobat 5.0
(CD-ROM)
ꢁInstallation Guide
(This manual)
1.1 Checking the Contents of the Scanner Package
2
Download from Www.Somanuals.com. All Manuals Search And Download.
No.
1
Name
Operator panel
Power button
Hopper
Function
Used for operating the scanner.
Used to power the scanner on/off.
Document input tray.
2
3
4
Side guides
Used for adjusting the document width.
Used for long documents.
5
Hopper extension
6
ADF (Automatic docu- Feeds documents automatically.
ment feeder)
7
Pick roller unit
Guide plate
Picks top page from document stack.
The pad assy is mounted on.
8
9
Pad Assy
Separates top page from document stack.
Opens for easy access.
10
11
12
13
14
15
16
17
18
19
20
Upper transport unit
Lever
Used to open the Upper transport unit.
Document exit tray.
Stacker
Stopper
Used to stop documents as they exit into the stacker.
Used to support long documents.
Controls supply of line power to the scanner.
For the power cable connection.
Ultra Wide SCSI (1pcs.)
Stacker extension
Main line switch
Power inlet
Interface connector
Third party slot (TPS)
Imprinter covers
Lamp covers
For installing a option board
Opens to access print cartridge for replacement.
Opens to access back side lamp.
1.2 Names and Functions of Parts
4
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Function of Buttons
Button
Name
Function
Turns on/off when the main line switch is set to “I”.
Starts scanning in test mode.
Send to/Start
Stop
1
Clears the error if this button is pushed while the Check lamp is on or is
blinking.
Enter
Used for setup, or test mode.
Exit
Used for setup, or test mode.
Returns LCD display to “Ready” status.
Previous
Used for setup, or test mode.
Displays the previous menu item when this button is pushed.
Used for setup, or test mode.
Displays the next menu item when this button is pushed.
Next
Used for setup, or test mode.
Changes the setting of the selected item.
Used for setup, or test mode.
Changes the setting of the selected item.
1.3 Operator Panel
7
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Function of LEDs
LED
Function
Power
Lights when the power supply is switched on.
(Green)
Read
Light during scanning.
(Green)
Check
ꢀLights when a hardware alarm is detected.
Lights out when
button is pushed. (except initial errors)
(Yellow)
ꢀBlinks when an equipment error occurs.
Papaer jam or Double feed is detected.
Press [Stop] button to clear the error, and the LED lights out.
In the case of Paper jam, when the document is removed, and the
Upper transport unit is closed, the LED lights out automatically.
■ Function of LCD panel
LCD
Function
Displays the scanner sutatus and error messages.
1.3 Operator Panel
8
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Counter display
Batch counter and Abrasion counters are shown bellow:
Batch counter L
x
x
x
x
x
x
x
x
x
x
R
e
d
x
a
y
1
Abrasion counter K
Fig.1
Simultaneously press the both (Left) and (Right) button for at least one second, to
switch to the Life counter panel display as shown bellow:
Batch counter L
x
x
x
x
x
x
x
x
x
x
R
e
a
d
y
*
x
x
x
Life counter K
Fig.2
To return from “Fig.2” to “Fig.1”, press the both (Left) and (Right) button for at least
one second.
1.3 Operator Panel
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Counter
Functions
Batch counter
(Left) button The number of scanned documents from the
start of reading until "Paper empty" or an error
is detected. The counter is automatically reset
at the start of reading. This counter can be
used for checking the number of scanned
documents per batch.
is pressed for at
least one sec-
ond.
(Right)button This counter is increased by one per sheet.
The counter is not initialized until the power is
turned off. The counter can be used for
checking the number of scanned documents
per day.
is pressed for at
least one sec-
ond.
Abrasion counter
The abrasion counter counts the accumulated number of
scanned sheets. This counter is increased by one per sheet
scanned.
It is useful to check the cleaning cycle or the parts replacement
cycle. Refer to “Chapter7 OPERATOR PANEL MENUS of the
Opelator’s Guide” on page 155, included in “User Manual (CD-
ROM)” about how to reset this counter.
Life counter
Keeps a cumulative count of the total number of scans made by
the scanner. This counter is increased by one per sheet and may
be used to estimate of the device’s remaining life. This counter
cannot be reset.
The counter is not displayed when the value is 0.
ATTENTION
1.3 Operator Panel
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2 INSTALLATION AND
CONNECTIONS
This chapter describes how to install and connect the scanner to a
PC, and how to install the Fujitsu application software.
References to operating systems (OS) are indicated as follows:
Windows® 95
Windows® 98
Windows® Me
: Microsoft® Windows® 95 operating system
: Microsoft® Windows® 98 operating system
: Microsoft® Windows® Millennium Edition
operating system
Windows® 2000 : Microsoft® Windows® 2000 Professional
operating system
Windows® XP
: Microsoft® Windows® XP Home Edition
operating system
: Microsoft® Windows® XP Professional
operating system
Windows NT®
: Microsoft® Windows NT® operating system
Version4.0
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Installing the Scanner
The following shows the procedure for installing the scanner.
■ Cautions on placement of scanner
1. Move the scanner to the installing area.
Refer to the "Operator’s Guide" stored on the “User Manual (CD-ROM)” about
the dimensions of the scanner, and the space required for its installation.
Move the scanner with more than two people as it weights
ATTENTION
approximately 99 lbs (45 Kg).
When you moved scanner grab it at the bottom.
ATTENTION
2.1 Installing the Scanner
12
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Connecting the Scanner
■ Connecting the power cable
Connect the power cable to the power inlet of the device and to a outlet rated to
comply with scanner power requirements.
2
■ Connecting the interface cable
An interface cable and a SCSI card are required.
Use the following SCSI card to connect to PC.
Recommended SCSI card
ADAPTEC SCSI card 29160
ADAPTEC SCSI card 39160
Recommended interface cable
ADAPTEC ACK-LVD-CBL KIT
ADAPTEC ACK-68V-68HD-LVD
ADAPTEC ACK-68V-68HD-LVD-2M-ICE
KOFAX Adrenaline 650i
ADAPTEC ACK-LVD-CBL KIT
Use of other SCSI card may cause unstable scan operations.
If you use ADAPTEC SCSI card 29160/39160, make sure you install the proper
drivers and updates as described below:
2.2 Connecting the Scanner
13
Download from Www.Somanuals.com. All Manuals Search And Download.
(1) Use the driver attached to the SCSI card.
You can download the driver file for each OS from the following address:
ꢂFor ASC29160
&cat=/Product/ASC-29160
ꢂFor ASC39160
&cat=/Product/ASC-39160
(2) Install ASPI version 4.70 or above.
®
(For Windows 95, install the ASPI version 4.60.)
You can download the driver from the following address.
If you use "FUJITSU TWAIN32 Version9.x", you do not need to install the ASPI
driver.
®
®
®
®
ꢂFor Windows 98, Windows NT 4.0, Windows Me, Windows 2000 and
®
Windows XP
&cat=/Product/ASPI-4.70
®
ꢂFor Windows 95
=aspi32.exe
®
If you use Windows XP, you need the following.
(3) Please update the driver using the patch file provided from ADAPTEC.
From Device Manager, click “Update Driver”.
You can download the update file from the following address.
file name : u160_winxp_drv_rc1.exe
Product/ASC-29160&filekey=u160_winxp_drv_rc1.exe
2.2 Connecting the Scanner
14
Download from Www.Somanuals.com. All Manuals Search And Download.
(4) For other OS, refer to the following ADAPTEC address to get the necessary
update files and revises the driver.
ꢂFor ASC29160
&cat=/Product/ASC-29160
ꢂFor ASC39160
&cat=/Product/ASC-39160
When connecting the SCSI interface cable, be sure to first
ATTENTION
connect the SCSI interface cable then turn on the power of
the scanner and the PC.
2
Connect the scanner so that it is the terminal device on the
ATTENTION
SCSI daisy chain.
The SCSI card and SCSI interface cable need to be pur-
ATTENTION
chased separately.
If the file address at ADAPTEC is changed, go to the
ADAPTEC site
HINT
to [Support]-[Downloads] to get the necessary files and
update information.
2.2 Connecting the Scanner
15
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Connect and use the thumbscrews to fix the interface cable into the
interface connector of the scanner.
(Back side)
Interface connecter
2. Connect and fix the other end of the interface cable to the PC.
The factory default setting for SCSI ID is “No.5”.
If the SCSI ID of another SCSI device is set to the same ID,
HINT
either change the scanner’s SCSI ID or change the SCSI ID
of the other SCSI device.
For details on how to change the SCSI ID, refer to the "Chap-
ter 7. OPERATOR PANEL MENUS of the Operator’s Guide"
on page 155, included in the “User manual (CD-ROM)” .
2.2 Connecting the Scanner
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Turn on the scanner
Press the side of “ | ” on the Main line switch.
Power on !
Main line switch
2
(Back side)
Then press the Power button on the Operator panel.
When the power is supplied, the green LED on the Operator panel lights.
Power Button
2.2 Connecting the Scanner
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Press the power switch on your PC.
2.2 Connecting the Scanner
18
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Installing the Scanner Driver and
Application
To enable scanning of documents on the scanner, the Scanner driver (FUJITSU
TWAIN32 scanner driver) and Image Capturing Software Utilities “ScandAll 21”
(ScandAll 21) or other scanning package must be installed on your PC.
This section explains about installing the FUJITSU TWAIN32 scanner driver and Image
Capturing Software “ScandAll 21” (ScandAll 21) .
For further details on installing the FUJITSU TWAIN32 scanner driver, refer to the
®
®
Scanner Utility for Microsoft Windows User’s Guide on the scanner driver CD-ROM.
The flowchart for the Scanner Driver installation
2
Power on the scanner.
Power on the PC.
Windows 95
WindowsNT 4.0
Windows 98/
Windows Me/
Windows 2000/
Windows XP
Install "Mini driver".
Install "TWAIN data source".
The scanner driver consists of a “Mini driver” part and a
“TWAIN data source” part.
ATTENTION
2.3 Installing the Scanner Driver and Application
19
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Installing FUJITSU TWAIN32 Scanner Driver
When you use Windows®98, Windows®Me, Windows®2000, and
Windows®XP (Please use FUJITSU TWAIN32 Version 9.9.)
Install the TWAIN data source after installing the mini-driver.
ATTENTION
If a old version of FUJITSU TWAIN32 Scanner driver is
ATTENTION
®
installed to your PC, refer to the "Scanner Utility for Microsoft
®
Windows User's Guide" of the Scanner driver (CD-ROM) to
update the mini-driver.
®
The Windows XP screen samples are shown below. The
ATTENTION
screens and operations will differ slightly depending on your
OS type.
(1) Preparation
Confirm that the Scanner is connected to your personal computer with a SCSI
interface cable.
2.3 Installing the Scanner Driver and Application
20
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Installing the mini-driver
1. Turn on the power by pushing the power switch on the scanner's control panel.
The green LED on the control panel lights, and then “Ready“ is displayed on the
LCD.
®
2. Turn on your PC and log on to Windows .
®
®
When using Windows 2000 or Windows XP, log on as an administrator.
The "Found New Hardware Wizard" dialog box is displayed.
3. Check "Install from list or specified location", then click [Next>].
2
®
•For Windows Me check "Specify the driver location", then click [Next>].
®
®
•For Windows 2000 and Windows 98, clicking on [Next>] the select search
method screen is displayed.
®
•For Windows 98 select "Find the most suitable driver for the device being used"
then click [Next>].
®
•For Windows 2000 select "Find the most suitable driver for the device" then click
[Next>].
2.3 Installing the Scanner Driver and Application
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Insert the Scanner driver (CD-ROM) into the CD-ROM drive
If automatic start has been set up, the start up screen for the
HINT
setup disk is displayed.
Click the [Exit] button and close this screen.
2.3 Installing the Scanner Driver and Application
22
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Select "Find the most suitable driver in the next location". Check "Include the next
location" then specify D:\Driver2 (If your CD-ROM is the D drive). After that click
[Next>].
2
®
•For Windows 98, just check "Specify search location" then specify D:\Driver2 (If
your CD-ROM is the D drive). After that click [Next>].
®
•For Windows Me, select "Find the most suitable driver for the devise being used"
then click [Next>]. Check "Specify search location" then specify D:\Driver2 (If your
CD-ROM is the D drive). After that click [Next>].
®
•For Windows 2000, just check "Specify location" and then in the next screen
specify "Copy source for origination file" then specify D:\Driver2 (If your CD-ROM
is the D drive), then click [OK].
2.3 Installing the Scanner Driver and Application
23
Download from Www.Somanuals.com. All Manuals Search And Download.
®
6. For Windows XP, the next screen is displayed, click [Continue] and complete the
installation. For other operating systems click [Next>].
®
For Windows 2000, “Digital Signature Not Found“ is dis-
ATTENTION
played. Click [Yes] and continue the installation.
®
For Windows 98 there is a request to insert a disc. When this
ATTENTION
®
happens, insert the Windows 98
CD-ROM.
2.3 Installing the Scanner Driver and Application
24
Download from Www.Somanuals.com. All Manuals Search And Download.
7. The following screen is displayed, Click [Finish].
2
8. Restart the system.
After restarting the system, install the TWAIN data source.
2.3 Installing the Scanner Driver and Application
25
Download from Www.Somanuals.com. All Manuals Search And Download.
®
®
®
(3) When you use Windows®98, Windows Me, Windows 2000, Windows XP,
select Driver Installation screen for TWAIN32 V9.9.
1. Insert the Scanner Driver CD-ROM, then use the explorer to double click on
D:\Driver2\Setup\install.exe (If your CD-ROM is the D drive).
When automatic start has been set up, start up screen for the
setup disk is displayed.
HINT
2. Follow the instruction on the screen to complete the installation. Make the best
selection that suits your needs.
•Select the language you will use during installation.
•Check the names of components that need to be installed in [Select Components].
Explanation of the component is displayed below.
•Check the installation directory. If you need to change the installation destination,
click the [Change Directory] button then specify the destination.
•Click the [Continue] button to start the installation.
2.3 Installing the Scanner Driver and Application
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When installation is finished, confirm that the following folder has been created.
The icons displayed differ depending on the setting in [Select Component] during
installation.
2
When installing the “TWAIN data source”, the folder named
HINT
[Scanner Utility for Microsoft Windows] is created in [Start]-
[Programs].
Continue, installation of the Image Capturing Software "ScandAll 21".
2.3 Installing the Scanner Driver and Application
27
Download from Www.Somanuals.com. All Manuals Search And Download.
When you use Windows®95 or WindowsNT®4.0 (Please use FUJITSU
TWAIN32 Version 8.9.)
(1) Preparation
1. Confirm that the SCSI adapter is attached to your personal computer.
2. Confirm that the SCSI driver and ASPI manager are correctly integrated and
operating.
ASPI manager Version 4.01 or later is required.
ATTENTION
Check the WNASPI32.DLL file version with explorer as fol-
lows:
1. Open the WNASPI32.DLL file property.
2. Click “Version info” tab.
3. If an older version is installed, uninstall it before doing the installation.
(2) Installation
1. Turn on the power by pushing the power button on the scanner's control panel.
The green LED on the control panel lights and "Ready" is display on the LCD after
warm up.
®
2. Turn on your PC and log on Windows .
®
When using Windows NT 4.0, log on as an administrator.
Select Installation Twain32 V8.9.
3. Insert the Scanner driver (CD-ROM) to the CD-ROM drive and/or use explorer to
double click on D:\Driver1\ASPI\install.exe (when your CD-ROM is the D drive).
2.3 Installing the Scanner Driver and Application
28
Download from Www.Somanuals.com. All Manuals Search And Download.
.
When automatic start has been set up, start up screen for the
setup disk is displayed.
HINT
Click the [Exit] button and close this screen.
2
4. Follow the instruction on the screen to complete the installation. Make the best
selection that suits your needs.
•Select the language you will use during installation.
•Check the names of components that need to be installed in [Select Components].
Explanation of the component is displayed below.
•Check the installation directory. If you need to change the installation destination,
click the [Change Directory] button then specify the destination.
•Click the [Continue] button to start the installation.
2.3 Installing the Scanner Driver and Application
29
Download from Www.Somanuals.com. All Manuals Search And Download.
5. When installation is finished, confirm that the following folder has been created.
The icons displayed differ depending on the setting in [Select Component] during
installation.
When installing the “TWAIN data source”, the folder named
[Scanner Utility for Microsoft Windows] is created in [Start]-
HINT
[Programs].
Continuously, install the Image Capturing Software "ScandAll 21".
2.3 Installing the Scanner Driver and Application
30
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Installing "ScandAll 21"
®
®
When using Windows NT 4.0, Windows 2000 or Win-
ATTENTION
®
dows XP, log on as an administrator .
1. Insert the Scanner driver CD-ROM to the CD-ROM drive and use select installation
under ScandAll 21 or ScandAll 21 in the [ScandAll] folder in the CD-ROM drive.
When automatic start has been set up, start up screen for the
setup disk is displayed.
HINT
Click the [Exit] button and close this screen.
2
2.3 Installing the Scanner Driver and Application
31
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select the language you use during installation in [Choose setup Language] then
click [OK]. This screen might not be displayed.
3. Click [Next>] in the following screen.
2.3 Installing the Scanner Driver and Application
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Carefully read the License Agreement then click [Yes], if you agree.
2
5. Confirm the name of the destination folder then click [Next>].
2.3 Installing the Scanner Driver and Application
33
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The following screen is displayed, Click [Finish].
2.3 Installing the Scanner Driver and Application
34
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Scanning documents
Confirm that the scanner works properly, as follows.
1. Place a document on the hopper. For details on how to load documents, refer to
"fi-4860C Operator’s Guide” included in the “User Manual (CD-ROM)”.
®
®
®
When using Windows 98, Windows Me, Winows 2000, or
ATTENTION
®
Windows XP and the documents are set on the hopper, an
application may start automatically or a window to select an
application appear. If you want to change these setting, refer
®
®
to "6.3 Event tab" of "Scanner Utility for Microsoft Windows
2
Version 9.9 User’s Guide".
2. Start ScandAll 21.
Select [Program]-[Scanner Utility for Microsoft Windows]-[ScandAll 21] In the start
menu.
2.3 Installing the Scanner Driver and Application
35
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Specify the scanner you use.
Select [Select Source] from the [Scan] menu in ScandAll 21.
The following dialog is displayed,
- Select "FUJITSU fi-4860CEAdij" when using FUJITSU TWAIN32 Version 9.8.
- Select "FUJITSU TWAIN32" when using FUJITSU TWAIN32 Version 8.8.
Then click [Select].
The part of the model name 'EAdij' varies depending on
ATTENTION
options.
2.3 Installing the Scanner Driver and Application
36
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click [Scan to View] button in the toolbar.
5. In [TWAIN Driver] (Scan conditions setting screen) select the scanning resolution,
paper size and other scanning conditions. Then click the [Scan] button.
For details on settings in the [TWAIN Driver] dialog box, refer to the "Scanner
®
®
Utility for Microsoft Windows User's Guide" on the Scanner driver (CD-ROM).
2
2.3 Installing the Scanner Driver and Application
37
Download from Www.Somanuals.com. All Manuals Search And Download.
6. The document is scanned and the image is displayed on the ScandAll 21 screen.
If the document can be scanned then setup has been successfully finished.
Refer to "ScandAll 21 Help" for information about ScandAll 21 functions and
operations.
The screen images may be changed due to improvements
ATTENTION
without notice.
If the displayed screen images are slightly different from the
screen images in "fi-4860C Quick Installation Guide", follow
the actual screen display for installation. Please also refer to
the software operation manual and implement the installation
according to the actual screens.
2.3 Installing the Scanner Driver and Application
38
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX-1 MESSAGES OF
OPERATOR PANEL
■ Massages of Scaner Operation Status
<Not Ready status> ꢃchanges to ꢀwith progress of time, and when all become ꢀ, it
move to the following check states.
(Initializing)
ꢁ
ꢁ
ꢁ
ꢀ
ꢀ
ꢀ
ꢀ
<Not Ready status>
p
p
j
a
e
r
c
m
t
i
e
o
r
w
E
W
i
n
n
g
g
-
a
e
o
p
N
(Ejecting document)
!
!
u
u
!
<Not Ready status>
i
n
n
g
g
-
s
p
n
N
s
o
o
w
C
W
h
a
e
r
c
m
k
i
r
!
(Checking sensor)
<Not Ready status>
h
p
p
N
e
w
r
!
R
W
e
a
s
r
e
m
t
i
i
n
n
g
g
-
p
o
(Reseting the hop-
per)
u
!
<Not Ready status>
W
a
i
t
i
n
g
I
F
R
e
a
d
y
(Waiting to initialize
interface board)
Low ink alarms
a
e
p
n
r
k
e
e
e
a
p
r
r
P
a
l
l
l
e
n
s
w
p
(
e
e
e
e
e
<preparing the print
cartridge>
I
I
I
)
a
e
p
n
r
k
a
p
r
o
P
a
e
n
s
w
p
(
e
s
(At power on )
t
)
)
a
e
p
n
r
k
a
B
r
o
P
a
e
n
s
w
p
(
e
t
h
AP-1
Download from Www.Somanuals.com. All Manuals Search And Download.
<Scanning>
P
N
e
w
a
s
R
a
d
n
n
e
g
w
!
I
x
n
x
l
o
e
e
k
x
a
i
x
"xxxx" shows the number of Batch counter value.
HINT
<Scanning>
N
o
w
R
e
a
d
i
n
g
!
x
x
x
x
"xxxx" shows the number of Batch counter value.
HINT
<At Low power
mode>
When the messages of LCD on the Operation panel disappears
and the Power LED lamp lights, the scanner is in Low power
mode.
The scanner wake up from Low power mode by one of the fol-
lowing operations.
TTENTION
ꢂPress any button (except power button) on the Operator
Panel.
ꢂSet the documents on the Hopper.
ꢂSend the command from PC.
AP-2
Download from Www.Somanuals.com. All Manuals Search And Download.
<Double feed error> The following message is displayed while the scanner is scan-
ning continuously in the state where double feed has detected
(by thickness check).
(Scanning)
If a double feed detection state is canceled on “Ready“ screen
after scanning, the upper row of this message disappear.
D
w
o
u
R
l
a
e
d
F
n
e
g
e
!
d
x
b
e
N
o
i
x
x
x
"xxxx" shows the number of Batch counter value.
HINT
(Waiting)
The following message is displayed while the scanner is waiting
in the state where double feed (check in thickness) has
detected.
Press the
canceled.
button, and the double feed detection state is
The upper row of this message, [Double Feedxxxxx] blinks.
o
u
R
l
a
e
d
F
e
x
e
x
d
x
x
x
x
x
x
x
x
x
x
x
D
b
e
y
"xxxx"(upper) shows the number of Batch counter value.
HINT
"xxxxxxxx"(lower) shows the number of Abration counter or
Life counter value.
AP-3
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Error mesage (Temporary error :Check LED blinking)
Check LED blinks when the following errors occur except <Hopper empty> and <Mis-
pick>.
<Hopper empty>
The following messages are displayed if no documents are on
the hopper during the scanning opperation. Please place docu-
ments on the hopper. Scanning is continued, when placing doc-
uments on the hopper for re-scanning.
To clear this message, press the
button.
x
t
x
y
x
x
x
P
a
p
e
r
E
m
p
Check LED does not blink at Hopper empty error.
HINT
(at Double feed)
D
o
u
P
l
p
e
e
x
x
x
F
e
E
e
m
d
p
x
t
x
y
b
a
r
"xxxx" shows the number of Batch counter value.
HINT
<Paper Jam>
The following message displayed if a document is jammed in the
ADF.
Refer to “Operator guide” included in “User manual CD-ROM”
for removing the document remained in the scanner.
P
a
p
e
r
J
a
m
x
One of "1" - "8" is displayed instead of "x", depending on
paper jam status.
HINT
AP-4
Download from Www.Somanuals.com. All Manuals Search And Download.
<ADF cover open>
The following message is displayed if the ADF cover is not
closed completely.
Close the ADF cover completely, to enable scanning.
A
D
F
-
C
o
v
e
r
O
p
e
n
<Double feed error> The following message is displayed, when the double feed is
detectied by thickness check.
(by thickness check)
D
o
u
l
e
F
e
e
d
b
(by length check)
The following message is displayed, when the double feed is
detectied by length check.
L
e
n
t
h
e
r
r
o
r
g
<Mis-pick>
The following message is displayed, when a document is not
sent from the hopper to the ADF.
M
s
-
p
i
c
k
i
Check LED does not blink at Mis-pick error.
HINT
<Pick over run>
The following message is displayed, when a document is sent
from the hopper to the ADF and it goes into too much than the
normal position.
i
c
k
P
o
v
e
r
r
u
n
AP-5
Download from Www.Somanuals.com. All Manuals Search And Download.
<Skew error>
The following message is displayed, When skewed document is
fed from the hopper to the ADF.
I
r
r
g
u
l
e
r
a
r
p
a
p
e
<Hopper is full or
Pick unit not set>
The following message is displayed, when the Pick roller unit is
not set correctly or when there are too many documents.
(When the documents are on the hopper.)
H
o
p
e
r
a
d
o
v
e
r
l
o
p
<Pick unit not set>
<Pick unit not set>
The following message is displayed, when the Pick roller unit is
not set correctly.
(When the documents are not exist on the hopper.)
P
i
c
r
o
o
t
n
i
t
l
l
s
e
e
r
t
u
k
n
The following message is displayed, when the Pick roller unit is
not set correctly during scanning.
P
i
c
r
o
n
i
t
l
l
e
r
u
k
<Break roller not
set>
The following message is displayed, when scanning while the
Break roller unit is not set correctly.
B
e
n
a
o
k
t
r
s
o
e
l
t
l
e
r
r
AP-6
Download from Www.Somanuals.com. All Manuals Search And Download.
<Separation roller > The following message is displayed, when rotating the Separa-
tion roller and the Brake roller does not rotate at all.
S
o
p
l
a
e
r
r
a
t
w
i
o
o
r
n
n
e
l
r
<Checking Consum- The following message is displayed, when the Abration counter
ables>
value exceeds the setting value to display an consumables
replacement message.
A
b
a
t
i
o
n
a
l
a
r
m
r
<Print cartridge not The following message is displayed, when the Print cartridge is
set>
not set to fi-486PRFR (Imprinter of front-side) or to fi-486PRRE
(Imprinter of rear-side).
P
o
r
e
I
N
N
n
k
k
d
d
g
g
e
e
C
C
a
a
r
r
t
t
r
r
i
i
P
o
o
s
I
t
n
AP-7
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Alarm message (Hardware error :Check LED lighting)
The following messages are displayed, when an error occurs inside the sccaner. In this
case, please switch on the power supply once again after disconnecting the power
supply.
If the same message is displayed again, please contact to a distributor or an nearest
imaging service and support center for help.
<Optical alarm >
(Front side)
The following message is displayed, when an error occurs to the
front side optical unit.
F
O
r
p
o
t
t
c
S
l
n
i
i
d
A
e
l
a
a
r
m
<Optical alarm >
(Back side)
The following message is displayed, when an error occur to the
back side optical unit.
B
O
a
p
c
t
S
a
k
i
i
l
d
e
A
c
l
a
r
m
<Motor fuse alarm> The following messages are displayed, when the fuse of various
motors (Toransport motor, Separation motor, Pick motor, Hop-
per motor) goes out.
(Toransport motor)
F
F
u
e
s
e
m
r
e
d
a
m
l
o
a
t
r
o
(Separation motor)
(Pick motor)
F
a
u
r
s
a
m
o
e
t
a
o
l
n
a
r
m
S
p
i
e
t
o
r
F
P
u
i
s
c
m
r
e
k
a
m
l
o
a
t
r
o
(Hopper motor)
F
o
u
p
s
p
m
o
e
e
a
l
m
a
o
r
t
H
r
r
AP-8
Download from Www.Somanuals.com. All Manuals Search And Download.
<Lamp fuse alarm> The following message is displayed, when the fuse for the lamp
for front side belows out.
(Front side)
F
n
u
t
s
m
a
e
s
a
d
l
e
a
r
l
F
o
i
r
m
p
<Lamp fuse alarm> The following message is displayed, when the fuse for the lamp
for back side belows out.
(Back side)
F
c
u
k
s
m
a
e
s
a
d
l
e
a
r
l
B
a
i
m
p
<Background fuse
alarm>
The following message is displayed, when the fuse for changing
the Background of front side belows out.
(Front side)
F
k
u
g
s
r
m
r
e
o
a
n
l
d
a
:
r
F
B
c
u
a
n
t
o
<Background fuse
alarm>
The following message is displayed, when the fuse for changing
the Background of back side belows out.
(Back side)
F
k
u
g
s
r
m
a
e
o
a
n
l
d
a
:
r
B
B
c
u
a
c
k
<Background fuse
error>
The following message is displayed, when the Background of
front side is unable to change.
(Front side)
F
k
o
r
n
o
t
u
s
d
i
d
A
e
l
r
g
B
c
n
a
a
r
m
<Background fuse
error>
The following message is displayed, when the Background of
back side is unable to change.
(Back side)
B
k
c
r
k
o
s
n
i
d
d
e
A
a
g
B
c
u
a
l
a
r
m
AP-9
Download from Www.Somanuals.com. All Manuals Search And Download.
<Hopper over run>
The following message is displayed, when the hopper moves
over the normal position.
H
o
p
e
r
u
n
o
v
e
r
r
p
<Sensor control
error>
The following message is displayed, when an error occurs in the
sensor control part.
e
n
s
o
A
r
l
C
r
o
m
n
S
t
l
r
o
a
<Sensor dirty error> The following message is displayed, when an error occurs owing
to a dirt on the sensor.
x
x
x
S
e
n
s
o
r
x
d
t
y
i
r
"xxxx." shows the sensor name (SF0, SA4, etc.)
HINT
<Sensor error>
The following message is displayed, when a sensor error occurs
x
x
x
S
e
n
s
o
r
x
e
o
r
r
r
"xxxx." shows the sensor name (SF0, SA4, etc.)
HINT
<Temprrature error> The following message is displayed, when the temperature
inside the scanner becomes higher than standard temperature.
T
e
m
p
a
e
l
r
a
a
r
t
m
u
r
e
AP-10
Download from Www.Somanuals.com. All Manuals Search And Download.
<Power supply
error>
The following message is displayed, when an error occurs in the
Power supply.
P
o
w
e
e
r
r
s
o
u
r
p
p
y
l
r
<EEPROM Alarm>
The following message is displayed, when an error occurs in
EEPROM.
A
E
D
E
D
P
R
R
E
O
S
M
S
x
l
x
a
H
r
A
m
The EEPROM address where the error occurs is displayed in
[xx] digit in the above sample screen.
HINT
<VDCC Read/Write The following message is displayed, when an error occurs dur-
error>
ing accessing to the area of VDCC.
V
C
C
2
R
/
W
E
D
r
r
r
o
(MDC timeout)
M
D
T
i
m
e
o
u
t
C
<Dither/Gamma
The following message is displayed, when an error occurs dur-
ing accessing to the Dither/Gamma RAM.
Read/Write error>
D
i
R
t
/
h
W
e
r
E
/
r
G
r
a
o
m
r
a
m
<Temporary mem-
ory Read/Write
error>
The following message is displayed, when an error occurs dur-
ing accessing to the temporary memory.
T
e
e
m
M
e
m
r
o
r
R
/
W
r
p
AP-11
Download from Www.Somanuals.com. All Manuals Search And Download.
<MDC download
error>
The following message is displayed, when an error occurs dur-
ing downloading the firmware to MDC.
M
D
C
d
r
o
r
w
o
n
r
l
o
d
a
E
<Imprinter alarm>
The following message is displayed, when an error occurs in
fi-486PRFR (Imprinter of front-side) or fi-486PRRE (Imprinter of
rear-side).
P
m
r
p
e
r
I
I
i
n
n
t
t
r
r
m
m
e
e
r
r
A
A
l
l
a
a
P
m
o
p
s
r
t
i
<Command alarm> The following message is displayed, when an error occurs in the
command sequence from PC.
(MDC command tim-
eout 1)
C
C
C
C
C
o
o
o
o
o
m
m
m
m
m
a
a
a
a
a
n
n
n
n
n
d
d
d
d
d
E
E
E
E
E
r
r
r
r
r
r
r
r
r
r
o
o
o
o
o
r
r
r
r
r
1
2
3
4
5
m
m
m
m
m
(MDC command tim-
eout 2)
(MDC command
Sequence error)
(MDC response
error)
(SCSI response time
out)
AP-12
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX-2 CONSUMABLES AND
REPLACEMENT CYCLE
The following table lists the Part No. and the standard replacement cycle of the
consumables. It is recommended you stock extra consumables before the ones on the
scanner reaches end of life. The consumables must be replaced periodically. You can
check the number of scanned pages for the Pad ASSY, the Pick roller unit, the Brake
roller unit, and Print cartridge, and you can check the cumulative lamp-on time for the
Lamps by referring to each counter on this scanner.
Descriptions
Lamp
Part No.
Standard replacement cycle
1,000 Hours (60,000minutes)
300,000 sheets or 1 year
300,000 sheets or 1 year
300,000 sheets or 1 year
PA83950-0290
CA04315-G730
PA03296-F711
CA04315-F705
CA00050-0262
Pad ASSY
Pick Roller Unit
Brake Roller Unit
Print Cartridge
Black ink cartridge
40,000sheets (10 characters/sheet)
The replacement cycle is based on the printing on Letter/A4 woodfree paper or wood
2
containing paper documents(64g/m ). The replacement cycle may differ due to paper
quality, print density or paper type.
For the purchase of the consumables, please contact the FUJITSU scanner dealer
where you purchased your scanner.
Use the correct Print cartridge. The Scanner may be dam-
TTENTION
aged if the wrong Print cartridge is installed.
AP-13
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX-3 TROUBLESHOOTING
Should any of the following problems arise, refer to the relevant section listed below.
ꢂScanner does not turn on.
Refer to Chapter 5.2 Troubleshooting “Synptom1” on page 120 of the fi-4860C
Operator’s Guide.
ꢂThe operator panel LCD goes out.
Refer to Chapter 5.2 Troubleshooting “Synptom2” on page 121 of the fi-4860C
Operator’s Guide.
ꢂScanning does not start.
Refer to Chapter 5.2 Troubleshooting “Synptom3” on page 122 of the fi-4860C
Operator’s Guide.
ꢂQuality of scanned pictures and photographs is not satisfactory.
Refer to Chapter 5.2 Troubleshooting “Synptom4” on page 125 of the fi-4860C
Operator’s Guide.
ꢂQuality of scanned text or lines is unsatisfactory.
Refer to Chapter 5.2 Troubleshooting “Synptom5” on page 127 of the fi-4860C
Operator’s Guide.
ꢂThe scanned image is distorted and/or not sharp.
Refer to Chapter 5.2 Troubleshooting “Synptom6” on page 128 of the fi-4860C
Operator’s Guide.
ꢂVertical streaks appear in the scanned image.
Refer to Chapter 5.2 Troubleshooting “Synptom7” on page 129 of the fi-4860C
Operator’s Guide.
ꢂCheck LED starts blinking right after power on.
Refer to Chapter 5.2 Troubleshooting “Synptom8” on page 130 of the fi-4860C
Operator’s Guide.
ꢂThe Check LED lights right after power on.
Refer to Chapter 5.2 Troubleshooting “Synptom9” on page 131 of the fi-4860C
Operator’s Guide.
ꢂDouble-feed occurs frequently.
Refer to Chapter 5.2 Troubleshooting “Synptom10” on page 132 of the fi-4860C
Operator’s Guide.
ꢂDocument jam occurs frequently.
Refer to Chapter 5.2 Troubleshooting “Synptom11” on page 135 of the fi-4860C
Operator’s Guide.
ꢂThere is a shadow on the leading edge of the scanned image.
Refer to Chapter 5.2 Troubleshooting “Synptom12” on page 138 of the fi-4860C
Operator’s Guide.
AP-14
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢂScanner is not recognized by PC automatically.
Refer to Chapter 5.2 Troubleshooting “Synptom13” on page 139 of the fi-4860C
Operator’s Guide.
®
ꢂWindows system gets unstable.
Refer to Chapter 5.2 Troubleshooting “Synptom14” on page 141 of the fi-4860C
Operator’s Guide.
AP-15
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX-4 CLEARING DOCUMENT
JAMS
If a document jam occurs during feeding, follow the procedure below to remove the
jammed documents.
- Be careful not to get injured during jam removal.
CAUTION
- When removing jammed documents, be careful not to get
your neckties or necklaces entangled inside the scanners.
- The surface of the glass sometimes becomes hot during
operation. Take care not to get burned.
■ Removing jams from the hopper or the transport
path
1. Remove the documents on the stacker.
2. Pull up on the lever on the right front of the Upper transport and then raise it.
Raise the Upper transport unit fully, then lower the transport to
engage lock before you put your hands inside of the scanner.
CAUTION
AP-16
Download from Www.Somanuals.com. All Manuals Search And Download.
3. While pulling the ADF lever toward you, lift up the ADF upper sheet guide.
ADF upper sheet guide
ADF release lever
4. Remove the jammed document.
- Staples and paper clips etc. can cause document jams.
TTENTION
- Make sure you check the document and the document trans-
port path for obstructions before you start scanning again.
- Remove staples and paper clips from the documents before
you start scanning.
5. Lower the ADF upper sheet guide carefully.
6. Lift the Upper transport unit fully to release the safety lock and then lower the
transport unit carefully.
■ Removing jams from the eject mechanism.
1. Remove the documents on the stacker.
2. Pull up on the lever on the right front of the Upper transport and then raise it.
AP-17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADF upper sheet guide
ADF release lever
3. Pull out the jammed document to the stacker.
4. Lift the Upper transport unit fully to release the safety lock and then lower the
transport unit carefully.
AP-18
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Document separation force adjustment
If the following error occurs frequently, adjust the brake force of the Brake roller using
setup mode.
- Double-feed
- Mis-pick
- Paper jam1
1. Enter into the setup mode.
Please refer to the section "1.3 Basic Operations of the Operator Panel" on page 6
of the fi-4860C Operator’s Guide, "Using the setup and test mode."
The following screen appears.
0
1
T
S
i
e
n
p
ꢀ
a
ꢀ
r
ꢀ
a
ꢁ
t
ꢁ
i
T
o
h
n
i
!
=
c
k
h
Choose an appropriate setting based on the thickness of the document you are
scanning and the error.
By pressing
By pressing
(Right arrow button), the LCD display changes items from (5) to (1).
(Left arrow button), the LCD display changes items from (1) to (5).
ꢀ ꢀ ꢀ ꢀ ꢀ
ꢀ ꢀ ꢀ ꢀ ꢁ
ꢀ ꢀ ꢀ ꢁ ꢁ
ꢀ ꢀ ꢁ ꢁ ꢁ
ꢀ ꢁ ꢁ ꢁ ꢁ
(1)
(2)
(3)
(4)
(5)
-
-
-
-
-
Document thickness: Thick
Document thickness: Medium thick
Document thickness: Medium
Document thickness: Medium thin
Document thickness: Thin
When the desired option appears, press
(Enter button) to select it.
AP-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Document separation force setup items are as follows.
Setting
Document
thickness
Document sep-
aration force
"Double-
feed"occurs
frequently
"Mis-pick"
or "Docu-
ment jam"
occurs fre-
quently
Thick
Thick
Strong
Increase doc- Decrease doc-
ument separa- ument separa-
Medium
Thick
Medium Thick Less strong
tion force
tion force
Medium
Medium
Medium
(Factory default
setting)
Medium
Thin
Medium Thin Medium Easy
Thin
Thin Easy
If Mis-pick occurs frequently, adjust the Pick roller rotation speed.
Press
(Next button) to show the following screen.
0
3
F
P
s
i
t
c
/
k
M
S
d
p
/
e
S
e
l
d
o
!
=
w
a
i
Press
Press
(Left arrow button) or
(Right arrow button) and select an item.
(Enter button) to select the setting.
The blinking item is the one selected.
HINT
AP-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Pick speed
Mis-pick occurs frequently.
Decrease pick speed
Fast (Factory default)
Mid
Slow
When you set pick speed at "Mid" or "Slow", scanning speed
is reduced.
TTENTION
AP-21
Download from Www.Somanuals.com. All Manuals Search And Download.
AP-22
Download from Www.Somanuals.com. All Manuals Search And Download.
M
U
N
O
P
R
S
T
● IN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
fi-4860C Image Scanner Installation Guide
P3PC-E177-02EN
Date of issuance: January, 2003
Issuance responsibility: PFU LIMITED
Printed in Japan
• Copying of the contents of this manual in whole or in part and copying of the scanner
application is forbidden under the copyright law.
• The contents of this manual are subject to change without notice.
• PFU LIMITED. is not liable whatsoever for any damages resulting from use of this
scanner and procedures described in this manual, profit due to defects, and any
claims by a third party.
• For details on the scanner's warranty conditions, refer to the stipulations on the
warranty packaged with the scanner.
• Repair parts for this scanner are retained for a minimum of five years from
discontinuation of production.
• Missing or wrongly collated pages will be supplied free of charge.
Download from Www.Somanuals.com. All Manuals Search And Download.
This Manual uses recycled paper.
Download from Www.Somanuals.com. All Manuals Search And Download.
|