P3PC-E677-02EN
fi-4220C Image Scanner
Operator's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
fi-4220C Image Scanner Operator’s Guide
i
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Items to Check Before Contacting the Agent Where
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
fi-4220C Image Scanner Operator’s Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing the fi-4220C Duplex Color Scanner product.
This document describes how to handle fi-4220C Duplex Color and basic operation methods. Before you
start using fi-4220C Duplex Color be sure to thoroughly read this manual to ensure correct use.
■ Regulatory Information
FCC Declaration
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is located.
•Consult your dealer or an experienced radio/TV technician.
FCC warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The use of a shielded interface cable is required to com-
NOTICE
ply with the Class B limits of Part 15 of FCC rules.
The length of the AC cable must be 2 meters (6.6 feet)
or less.
fi-4220C Image Scanner Operator’s Guide
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Canadian DOC Regulations
This digital apparatus does not exceed the Class B limit for radio noise emissions from digital
apparatus set out in the Radio interference Regulations of the Canadian Department of
Communications.
This Class B digital apparatus complies with Canadian ICES-003.
Le pésent appareil numérique n’ément pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la classe B prescridtes dans le Réglesment sur le brouillage
radioélectrique dicté par le ministere des Communications du Canada.
Cet appareil numérique de la classe B est conformme à la norme NMB-003 du Canada.
Bescheimigung des Herstellers / Importeurs
Hiermit wird bescheinigt, daß der/die/das fi-4220C
•In Übereinsstimmung mit den Bestimmungen der EN45014 (CE) funkentstört ist.
•Laut Maschinenlärminformationsverordnung 3. GS GV, 18.01.1991: Der höchste Schalldruckpegel
beträgt 70 dB (A) oder weniger gemäß ISO/7779.
®
International ENERGY STAR Program
As an ENERGY STAR® Partner, PFU LIMITED has determined that this product
meets the ENERGY STAR® guidelines for energy efficiency.
The International ENERGY STAR® Office Equipment Program is an international
program that promotes energy saving through the penetration of energy efficient
computers and other office equipment. The program backs the development and dissemination of
products with functions that effectively reduce energy consumption. It is an open system in which
business proprietors can participate voluntarily. The targeted products are office equipment such as
computers, monitors, printers, facsimiles, copiers, scanners, and multifunction devices. Their
standards and logos (
) are uniform among participating nations.
Use in High-safety Applications
This product has been designed and manufactured on the assumption that it will be used in office,
personal, domestic, regular industrial, and general-purpose applications. It has not been designed and
manufactured for use in applications (simply called "high-safety applications" from here on) that
directly involve danger to life and health when a high degree of safety is required, for example, in the
control of nuclear reactions at nuclear power facilities, automatic flight control of aircraft, air traffic
control, operation control in mass-transport systems, medical equipment for sustaining life, and
missile firing control in weapons systems, and when provisionally the safety in question is not
ensured. The user should use this product with adopting measures for ensuring safety in such high-
safety applications. PFU LIMITED assumes no liability whatsoever for damages arising from use of
this product by the user in high-safety applications, and for any claims or compensation for damages
by the user or a third party.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
About the use of mercury
The scanner lamps contain mercury.
To avoid unexpected injury, read the following carefully.
Doing the following actions may result in serious personal injuries:
•Do not put the substance in the lamp in your mouth as it contains mercury.
•Do not incinerate, crush, or shred the lamps or scanner.
•Do not breathe the chemical liquid contained in the scanner lamps.
Disposing of the scanner should be conducted as required by local ordinances or regulations.
Trademarks
Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
ISIS, QuickScan and their respective logos are trademarks or registered trademarks of Pixel
Translations, a division of Captiva Software Corporation in the United States.
Adobe, the Adobe logo, and Acrobat are either registered trademarks of Adobe Systems Incorporated
in the United States and/or other countries.
Other product names are the trademarks or registered trademarks of the respective companies.
How Trademarks Are Indicated In This Manual
References to operating systems (OS) are indicated as follows:
®
®
Microsoft Windows 95 operating system.
Windows 95
®
®
Microsoft Windows 98 operating system.
Windows 98
®
®
Microsoft Windows Millennium Edition operating system.
Windows Me
Windows NT 4.0
®
®
Microsoft Windows NT 4.0 Server operating system,
®
®
Microsoft Windows NT 4.0 Workstation operating system.
®
®
Microsoft Windows 2000 Professional operating system.
Windows 2000
Windows XP
®
®
Microsoft Windows XP Professional operating system,
®
®
Microsoft Windows XP Home Edition operating system.
Where there is no distinction between the different versions of the above operating system, the general
term "Windows" is used.
fi-4220C Image Scanner Operator’s Guide
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer
PFU LIMITED
Image Products Sales Dept., Imaging Products Division, Products Group
Solid Square East Tower, 580 Horikawa-cho, Saiwai-ku, Kawasaki-shi Kanagawa 212-8563, Japan
Phone: (81-44) 540-4538
All Rights Reserved, Copyright© PFU LIMITED 2003-2009
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Note, Liability
READ ALL OF THIS MANUAL CAREFULLY BEFORE USING THIS PRODUCT. IF THIS
PRODUCT IS NOT USED CORRECTLY, UNEXPECTED INJURY MAY BE CAUSED TO USERS
OR BYSTANDERS.
Also, store this manual in a safe place so that it can be easily referred to during use of this product.
While all efforts have been made to ensure the accuracy of all information in this manual, PFU
assumes no liability to any party for any damage caused by errors or omissions or by statements of any
kind in this manual, its updates or supplements, whether such errors are omissions or statements
resulting from negligence, accidents, or any other cause. PFU further assumes no liability arising from
the application or use of any product or system described herein; nor any liability for incidental or
consequential damages arising from the use of this manual. PFU disclaims all warranties regarding the
information contained herein, whether expressed, implied, or statutory.
Warning Indications Used In This Manual
This indication alerts operators to an operation that, if
not strictly observed, may result in severe injury or
death.
This indication alerts operators to an operation that, if
not strictly observed, may result in safety hazards to
personnel or damage to equipment.
Symbols Used In This Manual
This symbol alerts operators to particularly important information. Be sure to
ATTENTION
read this information.
This symbol alerts operators to helpful advice regarding operation.
HINT
A TRIANGLE symbol indicates that special care and attention is required.
The drawing inside the triangle shows the specific caution.
A CIRCLE with a diagonal line inside shows action which users may not
perform.
The drawing inside or under the circle shows the specific action that is not
allowed.
fi-4220C Image Scanner Operator’s Guide
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Outline characters on a colored background show instructions users should
follow.
R
It may also include the drawing that shows the specific instruction.
Screen Examples In This Manual
The screen examples in this manual are subject to change without notice in the interest of product
improvement. If the actual displayed screen differs from the screen examples in this manual, operate
by following the actual displayed screen while referring to the User's Manual of the scanner
application you are using. Furthermore, the screenshots in this manual are for the FUJITSU TWAIN32
scanner driver, ScandAll 21 Image Capturing Utility Software, FUJITSU ISIS scanner driver,
QuickScan™ image capturing software and Adobe® Acrobat®.
About Maintenance
The user must not perform repairs on this scanner.
Contact the store where you purchased the scanner or an authorized FUJITSU Image Scanner service
provider to make repairs to this product.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Safety Precautions
Do not damage the AC cable.
A damaged AC cable may cause fire or electric shock. Do not place heavy objects on
AC cables, or pull, bend, twist, heat, damage or modify AC cables. Also, do not use
damaged AC cables or power plugs, and AC cables or power plugs when the wall
socket is loose.
Use only specified AC cables and connector cables.
Use only specified AC cables and connector cables. Failure to use the correct cables
might cause electric shock and equipment failure.
Use this scanner only at the indicated power voltage.Do not
connect to multiple-power strips.
Use this scanner only at the indicated power voltage and current. Improper power
voltage and current might cause fire or electric shock. Also, do not connect to multiple-
power strips.
Do not touch the AC cable with wet hands.
Do not touch the power plug with wet hands. Doing so might cause electric shock.
Wipe any dust from the power plug.
Wipe off any dust from metal parts on the power plug or metal fittings with a soft, dry
cloth. Accumulated dust might cause fire or electric shock.
Do not install the device in locations subject to oil smoke, steam,
humidity, and dust.
Do not install the scanner in locations subject to oil smoke, steam, humidity, and dust.
Doing so might cause a fire or electric shock.
fi-4220C Image Scanner Operator’s Guide
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the scanner OFF if it is damaged.
If the scanner is damaged for any reason, turn off the scanner and unplug the power
cable before contacting the store where you purchased the scanner.
Do not put liquids inside the scanner.
Do not insert or drop metal objects in to the scanner. Do not scan wet documents or
documents with paper clips or staples. Do not splash or allow the scanner to get wet.
If foreign objects (water, small metal objects, liquids, etc.) get inside the scanner,
immediately turn off the scanner and disconnect the power plug from the power outlet,
then contact the store where you bought the scanner or the Maintenance Service
Center. Pay particular attention to this warning in households where there are small
children.
Do not touch the inside of the scanner unless necessary.
Do not take apart or modify the scanner. The inside of the scanner contains high-
voltage components. Touching these components might cause fire or electric shock.
Do not use the scanner if you smell a strange odor.
If you detect heat coming from the device or detect other problems such as smoke,
strange smells or noises, immediately turn off the scanner and then disconnect its
power plug. Make sure that the smoking has stopped, and then contact the store
where you bought the scanner or an authorized FUJITSU scanner service provider.
Do not install the scanner on unstable surfaces.
Install the scanner on a desk so that none of its parts protrude outside of the desktop.
Also, make sure that the scanner is installed on a flat, level surface. Do not install the
scanner on unstable surfaces. Install the scanner on a level surface that is free of
vibration to prevent it from falling.
Install the scanner on a strong surface that will support the weight of the scanner and
other devices.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not block the ventilation ports.
Do not block the ventilation ports. Blocking the ventilation ports generates heat inside
of scanner, which may results in fire or scanner failure.
Do not place heavy objects or stand on top of the scanner.
Do not place heavy objects on the scanner or use the scanner's top surface for
performing other work. Improper installation might cause injuries.
Firmly insert the power plug.
Firmly insert the power plug into the power outlet as far it can go.
Avoid any contact when scanner is in use.
Avoid touching any scanner mechanism when scanning as this may cause injuries.
Do not use the scanner immediately after moving it from a cold
place into a warm room.
Do not use the device immediately after moving it from a cold place into a warm room.
This may cause condensation, which might lead to scanning errors. Let the device dry
about one or two hours before you use it.
Before moving the scanner, disconnect the power plug from the
power outlet.
Do not move the scanner with the power and interface cables connected as this might
damage the cables, causing fire, electric shock or injuries. Before moving the
scanner, be sure to disconnect the power plug from the power outlet, and disconnect
data cables. Also, make sure that the floor is free of obstructions.
Protect the scanner from static electricity.
Install the scanner away from strong magnetic fields and other sources of electronic
noise. Also, protect the scanner from static electricity as this might cause the scanner
to malfunction
fi-4220C Image Scanner Operator’s Guide
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not use aerosol sprays near the scanner.
Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt and dust to
enter the scanner, resulting scanner failure and malfunction.
Disconnect the power plug from the power outlet when the
scanner is not used for a long period of time.
When the scanner is not used for a long period of time, be sure to disconnect the
power plug from the power outlet for safety.
Do not install the scanner in the direct sunlight.
Do not install the scanner in the direct sunlight or near heating apparatus. Doing so
might cause excessive heat to build up inside the scanner, causing fire or scanner
trouble. Install the scanner in a well-ventilated location.
Be aware of the pick spring.
When you perform cleaning, make sure that the inside of the scanner is free of any
foreign object, and be careful not to get your hand or the cloth caught on the pick
spring (metal part) as a deformed pick spring (metal part) may cause injury.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
BASIC SCANNER OPERATIONS
1
This chapter describes basic scanner operations.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
1.5 How to Use the Scanner Driver....................................................................... 10
fi-4220C Image Scanner Operator’s Guide
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Turning the Scanner ON
This section describes how to turn the scanner ON.
The following shows the procedure for turning the scanner ON.
1. Press the power button on the operator panel.
The scanner is turned ON, and the green LED on the operator panel lights.
Also, while the scanner is being initialized, the indication of the Function No. display
changes as follows:
"8" -> "P" -> "0" -> "1"
The indication "1" means that the operator panel is in the ready status.
Power button
To turn the scanner OFF, hold the power button down for two sec-
onds.
HINT
■ Power Save Mode
The Power Save mode keeps the scanner in a low-powered state after it has been turned ON.
If no operation is performed on the scanner for 15 minutes, the scanner automatically switches to
the Power Save mode.
In the Power Save mode, the indication of the Function No. display on the operator panel goes out,
but the green LED stays lit.
To return from the Power Save mode, perform one of the following:
• Load the document on the ADF paper chute.
• Press any button on the operator panel.
The scanner will be turned OFF when pressing down the power button for two seconds.
• Execute a command from the scanner driver.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Loading Documents on the ADF for Scanning
1.2 Loading Documents on the ADF for Scanning
1. Align the edges of the documents.
1) Confirm that all the documents have the same width.
2) Check the number of sheets in the document stack.
1
The standard number of sheets that can be loaded on the scanner is as follows:
• A4-size paper or smaller that makes a document stack of 5mm or less
• Maximum 50 sheet at A4, 20 lb, or 80 g/m2
2. Fan the documents as follows:
1) Lightly grip both ends of the document with both hands, and bend the document as fol-
lows.
5mm
2) Firmly holding the document with both hands, bend back the document as follows so that
the bent section rises up in the middle of the document as follows.
3) Repeat steps 1) to 3) a few times.
4) Rotate the document 90 degrees, and fan again.
3. Align the top of the documents.
fi-4220C Image Scanner Operator’s Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Load the document on the ADF paper chute.
Set the documents face-down in the ADF paper chute (so that the side to be scanned faces
towards the ADF paper chute).
Load the document facing
the ADF paper chute.(face down)
Before loading A4-size documents, pull out the ADF paper chute
extension.
HINT
Extension
4
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 Loading Documents on the ADF for Scanning
5. Adjust the side guides to the width of the documents.
Move the side guides so that they touch both sides of the documents.
If there is any space between the side guides and the edges of documents, the scanned image
may be skewed.
Side guide
1
The stacker prevents document sheets from dropping after they are
scanned.
HINT
Lift the paper stop and swing it forward by inserting your fingertips
into the indentaitons on the scanner as shown in the figure below.
Indentation
6. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, refer to "1.4 Scan-
fi-4220C Image Scanner Operator’s Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Loading Documents on the Flatbed for Scanning
1. Lift up the document cover.
2. Load the document on the document bed with the scanning face down and the top left
corner aligned with the reference point.
Align the top left
corner of the
document with the
reference point.
ABC
Reference point
3. Gently close the document cover.
4. Start up the scanner application, and scan the document.
For details on how to scan documents using the ScandAll 21 application, see "1.4 Scanning
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Scanning Documents
1.4 Scanning Documents
1. Load the document on the scanner's ADF paper chute or Flatbed.
For details on how to load documents, see "1.2 Loading Documents on the ADF for Scan-
1
2. Start up ScandAll 21.
Select [Start] - [Program] - [Scanner Utility for Microsoft Windows] - [ScandAll 21].
This starts up ScandAll 21.
3. Select the scanner to be used.
Select [Select Source] from the [Scan] menu.
⇒ The [Select Source] dialog box appears.
Select "FUJITSU fi-4220Cdj" (for Windows 95 and WindowsNT 4.0, select "FUJITSU
TWAIN 32") and click the [Select] button.
fi-4220C Image Scanner Operator’s Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Click the [Scan To View] button on the tool bar.
⇒ The [TWAIN Driver] dialog box (screen for setting the scan conditions) appears.
5. Set the scan resolution, paper size and other scan conditions, and click the [Scan]
button.
For details on settings in the [TWAIN Driver] dialog box, refer to "1.5 How to Use the Scan-
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Scanning Documents
⇒ The document is scanned, and an image of the scanned document appears on the
ScandAll 21 screen.
1
For details on scanning other types of documents, refer to "Chapter 2 SCANNING VARIOUS
For details on ScandAll 21 functions and operations, refer to ScandAll 21 Help.
fi-4220C Image Scanner Operator’s Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
■ FUJITSU TWAIN32 Scanner Driver
FUJITSU TWAIN32 Scanner Driver is designed for scanning documents with FUJITSU image
scanner fi series by using application software that complies with the TWAIN standard.
The following describes the procedure with examples of ScandAll 21 for ordinary scanning by
using this driver software.
1. Procedure for Basic Scanning Operation
1) Startup the application.
From the [Start] menu, select [Programs]-[Scanner Utility for Microsoft Window] and
click [ScandAll 21].
2) Select your scanner on the window below.
Select [Select Source] from the [Scan] menu.
3) Select the scanner to use, then click the [Select] button.
Select
• [FUJITSU fi-4220Cdj] for FUJITSU TWAIN32 V9
or
• [FUJITSU TWAIN32] for FUJITSU TWAIN32 V8
then click the [Select] button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
4) Load the documents on the scanner.
For details on loading documents, refer to "1.2 Loading Documents on the ADF for
5) Open the TWAIN Driver window.
Select [Scan To View] from the [Scan] menu.
1
ScandAll 21 provide scanning methods as follows:
HINT
• [To View...]: Displays scanned images on the window.
• [To File...:]: Saves scanned images as files (*.BMP, *.TIF, *.JPG).
• [To FTP...:]: Transfers scanned images to a FTP server.
• [To Adobe PDF...:]: Saves scanned images as PDF files.
(*Adobe Acrobat must be installed beforehand.)
• [To Microsoft SharePoint Portal Server...]: Transfers scanned images to
Microsoft Share Point Portal Server.
• [To Mail...]: Launches mailer software and attaches scanned images to e-
mail.
For details, refer to "ScandAll 21 Help".
6) Configure settings for scanning and click the [Scan] button.
For details about the settings on this window, refer to "Setting Window for FUJITSU
fi-4220C Image Scanner Operator’s Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
⇒ The images of scanned documents are displayed on the [ScandAll 21] window.
Depending on the settings of the application software, images may not be displayed.
For details, refer to the documentation or Help file of your application.
e.x.) When you select [To File...] from the [Scan] menu of ScandAll 21, images of
scanned documents are not displayed on the window.
7) Save the scanned images.
Select [Save As...] from the [File] menu to save the scanned images.
If you wish to start another scanning, return to procedure 4.
8) End the application.
Select [Exit] from the [File] menu.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
2. Setting Window for FUJITSU TWAIN32 Scanner Driver
1
You can configure settings for the FUJITSU TWAIN32 Scanner Driver on this window.
The following describes the main setting items.
• For details on each functions, refer to "FUJITSU TWAIN32 Scanner Driver Help"
(appears by pressing [Help] or [F1] button).
• Depending on the type of your scanner, available setting items or range of setting
values vary.
Resolution
Specifies the resolution of scanning.
It can be specified by selecting a default value from the list or customizing (specify any
resolution in 1 dpi unit).
By marking the [Predefine] checkbox, you can select one from three predefined set-
tings as [Normal], [Fine], [Super Fine] to scan documents instead of setting details by
yourself.
Otherwise, you can change the details of the predefined settings on the [Resolution Set-
ting] window, which appears when you click on the [...] button.
Scan Type
Specifies the feeding method, the side(s) to be scanned (Front Side, Back Side, Duplex)
or details of Long page (the size of documents longer than A3).
Paper Size
Select the size of documents to be scanned from this list.
Windows for customizing the paper size will appear when you click on [...] besides the
list. You can save any document size as a customized setting (up to three) or for chang-
ing the order of the paper size in the list.
fi-4220C Image Scanner Operator’s Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Mode
Specifies the image type for the scanned documents.
Black & White
Halftone
Documents are scanned in binary (black and white).
Documents are scanned through halftone process-
ing in black and white.
Grayscale
Color
Documents are scanned with 256 gradations from
black to white.
Documents are scanned in color. For this mode, you
can select 24 bit Color, 256 Color or 8 Color.
[Scan] button
Starts scanning documents with the current settings.
[Preview] button
Documents are scanned preliminarily before the actual scanning.
You can confirm the image of the documents in the preview window.
[Close] button
Saves the current settings and closes this window.
[Reset] button
Used to undo changes of settings.
[Help] button
Opens the "FUJITSU TWAIN32 Scanner Driver Help" window. The window also
opens by pushing the [F1] key.
[About...] button
Opens an information window about the FUJITSU TWAIN32 Scanner Driver's ver-
sion.
[Option...] button
You can set up the details of optional functions on the window below.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
[Rotation] tab
Select this tab when setting image rotation, detection of document size, etc.
[Job/Cache] tab
Select this tab when setting cache mode, double-feed detection, blank page skip-
ping, etc.
1
[Generic] tab
Select this tab to change the unit displayed on the Setting Window for the FUJITSU
TWAIN32 Scanner Driver. (Millimeters, Inches, and Pixels are available)
[Startup] tab
Select this tab for setting the Scanner Operation Panel.
(Displayed only when using the scanner of supported type.)
[Filter] tab
Select this tab for setting the image processing filter(s).
Page Edge Filler: Fills up the margins of the scanned documents with a selected
color.
[Compression] tab
Select this tab for setting the compression rate of JPEG Transfer.
[Advance...] button
Click this button for settings of the advanced image processing.
You can set Edge Extract, Gamma Pattern, White Level Follower, Dropout Color,
Reverse, etc.
[Config...] button
Click this button for configuring the Setting Files.
You can save the changed settings as a Setting File. From next scanning, the settings
are quickly changed by using these Setting Files.
For details of each function, refer to the "FUJITSU TWAIN32 Scsnner Driver Help".
fi-4220C Image Scanner Operator’s Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
■ FUJITSU ISIS Scanner Driver
FUJITSU ISIS Scanner Driver is designed for scanning documents with FUJITSU image scanner fi
series by using application software that complies with The ISIS standard.
The following describes the procedure with examples of QuickScan for ordinary scanning by using
this driver software.
The procedure may vary depending on your application. If you use an application other than
QuickScan, please refer to its Guide or Help for further information.
1. Procedure for Basic Scanning Operation
1) Startup the application.
From the [Start] menu, select [Programs] - [QuickScan] and click [QuickScan].
2) Select your scanner on the window below.
Select [Scan] - [Select Scanner] on the menu bar.
3) Select fi-4220C, then click the [OK] button.
4) Select [Scan] - [New Batch] on the menu bar.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
5) Select the profile for scanning.
1
•
•
•
When creating a new profile
Select one from already existing profiles and click [Add Profile...] button.
⇒ A new profile will be created based on the profile you select.
When changing the settings of already existing profiles
Select one from already existing profiles and click [Edit Profile...] button.
⇒ The settings of the selected profile can be changed.
When deleting a profile
Select the one to delete and click [Delete Profile] button.
⇒ The selected profile will be deleted.
When you added, edited or deleted a profile, go to the procedure 10.
6) Open the window of ISIS Driver.
Select the [Scan] tab and click the [Scanner Settings] on the [Profile Editor] window.
fi-4220C Image Scanner Operator’s Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
⇒ The configuration window of ISIS driver appears.
7) Configure settings for scanning and click the [OK] button.
For details on this dialog box, refer to "Configuration Window of FUJITSU ISIS Scan-
8) The [Profile Editor] window appears. Click the [OK] button to return to [New batch]
dialog.
9) Load the documents on the scanner.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
10) Click the [Scan] button.
1
⇒ Scanned images are displayed on the window.
Refer to the "QuickScan Overview" or the "QuickScan Help" for further information
on functions and operations of QuickScan. After the installation of QuickScan, it is reg-
istered in the [Start] menu.
2. Configuration Window of FUJITSU ISIS Scanner Driver
fi-4220C Image Scanner Operator’s Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode
Select a color mode suitable for the purpose from the menu.
Black & White
Scans data in binary (black and white). Distinguishes
black from white according to the fixed threshold.
This scanning mode is suitable for scanning line
drawings and text documents.
16-level Grayscale Scans data by 14 shades of gray plus black and white.
This mode uses 4 bits per pixel.
256-level Grayscale Scans data by 254 shades of gray plus black and
white. This mode uses 8 bits per pixel. This mode is
switable for scanning monochrome photographs.
24-bit Color
Scans data as full-colored image using 24 bits per
pixel. This mode is suitable for scanning color photo-
graphs.
Image Processing
Binary processing is applied to the scanned images
This mode is available only when Image Processing
Software Option (separately sold) is installed. Please
refer to the "User’s Guide of Image Processing Soft-
ware Option" for details.
Dots per inch
Specifies the number of pixels (dots) per inch.
Select a fixed resolution from the list or enter any value (from 50 to 600) manually.
A higher resolution produces finer image, but requires much more memory.
Dither
Select the halftone pattern for halftone scanning. This setting is available when "Black
& White" is selected in the "Image Mode".
Dither Pattern 0
Dither Pattern 1
Dither Pattern 2
Dither Pattern 3
Error Diffusion
This setting is suitable for scanning dark photo-
graphs.
This setting is suitable for scanning dark-colored
documents containing both text and photographs.
This setting is suitable for scanning light photo-
graphs.
This setting is suitable for scanning light-colored
documents containing both text and photographs.
This function minimizes differences of color levels
due to subtractive color process by diffusing the dif-
ference to the adjacent pixels. This mode is suitable
for scanning images of photographs, etc.
Executes processing with the dithered download pat-
tern specified in the dithered download file.
Download
Brightness
Sets the brightness of the entire image. Specify the brightness as a number within the
range of 1 (dark) to 255 (bright). To brighten the entire image, decrease the value of the
setting. To darken the entire image, increase the value.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
Contrast
Sets the contrast between light and shadow of the scanned image. Specify the contrast
as a number within the range of 1 (low [soft]) to 255 (high [sharp]). Increasing this
value makes the contrast sharper.
Source
Selects the scanning method.
1
ADF (Front Side)
ADF (Back Side)
ADF (Duplex)
Scans only the front sides of documents.
Scans only back sides of documents.
Scans both front and the back sides of documents.
When this option is selected, the both sides of docu-
ments are scanned simultaneously. This option can
be used only for the models that support duplex scan-
ning.
Paper Size
Selects a paper size according to the size of the document to be scanned. Select a stan-
dard paper size from the list.
Layout
Specifies orientation of the documents as portrait or landscape.
End of Page Detection
Scans the edge (bottom) of the documents and outputs data adjusted to the document
length. When any page shorter than specified "Paper Size" is included, the output size
is adjusted to the detected short size.
[More...] button
Opens [More Settings] window. Used for setting advanced features.
fi-4220C Image Scanner Operator’s Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
[Area...] button
Opens the Scan Area dialog box.
Specify scan area for the document size.
The size can be set by dragging the frame with mouse.
Otherwise, enter any value for the setting.
[JPEG...] button
Opens the JPEG Settings dialog box. Used for setting the compression rate of JPEG
transfer.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 How to Use the Scanner Driver
[About...] button
This button displays the version information.
1
Gamma
Specifies Gamma correction. Correction patterns are: "Normal", "Soft", "Sharp", "Cus-
tom", or "Download".
DTC Variance
This option specifies the value for adjusting the variance based on the brightness of the
image.
Edge Processing
This option specifies the sharpness of contour extraction.
Low, Mid, High
Emphasizes contour of images. Available settings
are: Low, Mid, High
Smoothing
Smoothes jaggy images.
Dropout Color
This option excludes selected color (the three primary colors of light i.e. green, red,
blue) from scanned images. For example, if the document contains black text in a red
frame and when the red color is selected, the scanner reads only the text and eliminate
(drop out) the red frame.
Reverse
Colors of scanned images are reversed.
Power saving
This option specifies the waiting time before the scanner switches to the Power save
mode.
fi-4220C Image Scanner Operator’s Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Double Feed Detection
Detects Double-feeds (phenomena that two or more sheets are accidentally fed). You
can set conditions for detecting Double-feeds so that the scanner should stop and dis-
play error messages. Double feeds are scanned by the differences in document lengths
or thicknesses.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
SCANNING VARIOUS TYPES OF
DOCUMENTS
2
This chapter describes how to scan various types of documents.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
2.1 Scanning Double Sided Docments................................................................. 26
2.2 Scanning in Books........................................................................................... 28
fi-4220C Image Scanner Operator’s Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Scanning Double Sided Docments
The following shows the procedure for reading the double sided documents.
1. Load the document on the ADF paper chute.
Load the document facing
the ADF paper chute.(face down)
2. Adjust the side guides to the width of the documents.
Side guide
3. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] -
[ScandAll 21]. This starts up ScandAll 21.
4. Select fi-4220C.
5. Click [Scan To View] on the tool bar. The [TWAIN Driver] dialogbox appears.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1 Scanning Double Sided Docments
6. Select [ADF (Duplex)] from [Scan Type].
2
7. Click the [Scan] button.
For [TWAIN Driver] dialog box setting, refer to "1.5 How to Use the Scanner Driver" (page.
⇒ The document is scanned, and an image of the scanned document appears on the
ScandAll 21 screen. For ScandAll functions and operation, refer to [ScandAll 21 Help].
fi-4220C Image Scanner Operator’s Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Scanning in Books
3. Read the document on the document bed face down.
2
4. Issue the scan command on the host system.
For details on scanning commands, refer to "1.4 Scanning Documents" (page. 7).
Do not move the document during scanning.
ATTENTION
5. When scanning ends, re-attach and gently close the document cover.
fi-4220C Image Scanner Operator’s Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Scanning Documents Larger Than A4 Size
Never look directly the light source during scanning.
1. Remove the document cover as shown in the figure below.
2. Load the document on the document bed face down.
3. Issue the scan command on the host system.
For details on scanning commands, refer to "1.4 Scanning Documents" (page. 7).
Do not move the document during scanning.
ATTENTION
4. When scanning ends, re-attach and gently close the document cover.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Scanning Different-width Documents
2.4 Scanning Different-width Documents
When you scan a batch of documents with different widths by using the ADF, you may get skewed
images from smaller sized documents.
Be sure to scan only documents of the same width together.
The following shows the procedure for scanning a batch of mixed size documents.
1. Sort out the batch into stacks of the same width.
2. Adjust the side guides to the width of each document stack.
3. Scan the batches of the same widths sparately one by one.
2
fi-4220C Image Scanner Operator’s Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Saving Scanned Images in PDF Format
To save scanned images in PDF format, Adobe Acrobat 5.0 or later must be installed on your PC.
Adobe Acrobat 5.0 can be installed from the provided Adobe Acrobat CD-ROM.
There are 2 ways for saving scanned images in PDF format.
1. Using ScandAll 21
This method is recommended for color or grayscale scanning and when smaller PDF
file size is required.
The benefits are:
• Reduced PDF data size
• Simplified method for creating PDF files with no troublesome operations
2. Using Adobe Acrobat 5.0
This method is recommended for faster creation of PDF files and for black and white scan-
ning.
The benefits are:
• Quick creation of PDF files with the original scan resolution
• Flexibile creation of PDF files by changing the PDF compression rates
Grayscale or color scanning creates larger file sizes than black and white scanning.
If the file size is very large, you can reduce the file size by configuring the properties of
Acrobat Distiller before saving scanned images.
For details, please refer to the hints on page 38.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Saving Scanned Images in PDF Format
■ Using ScandAll 21
1. Load the documents on the ADF paper chute or the flat bed.
2. Start up ScandAll 21.
From [Start] menu, select [Program] - [Scanner Utility for Microsoft Windows] -
[ScandAll 21]. This starts up ScandAll 21.
3. From the menu bar select [Scan] and then [To Adobe PDF] from the pull down menu.
2
⇒ [TWAIN Driver] dialog box is displayed.
fi-4220C Image Scanner Operator’s Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Select the scan resolution, document size and other scan conditions, and then click
the [Scan] botton.
5. To end scanning, click the [Close] button.
⇒ The scanned image is displayed.
6. Enter the file name and select the destination to save the scanned image.
For details, refer to ScandAll 21 Help.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Saving Scanned Images in PDF Format
■ Using Adobe Acrobat 5.0
1. Load the documents on the ADF paper chute or the flat bed.
2. Start up Adobe Acrobat 5.0.
Select [Program] - [Adobe Acrobat 5.0] from the [Start] menu. This starts up Adobe Acrobat
5.0.
3. From the [File] menu select [Import] - [Scan] in that order.
2
⇒ [Acrobat Scan Plug-in] dialog box is displayed.
4. Select [FUJITSU fi-4220Cdj] ([FUJITSU TWAIN 32] for WindowsNT 4.0) at [Device]
and click [Scan] button.
⇒ [TWAIN driver] dialog box is displayed.
fi-4220C Image Scanner Operator’s Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Select [Simplex] even if you intend to do duplex scanning.
HINT
5. Select the scan resolution, document size and other scan conditions, and click the
[Scan] button.
6. To end scanning, click the [Done] button.
⇒ The scanned image is displayed.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
2.5 Saving Scanned Images in PDF Format
2
7. Select [Save as] or [Save] from [File] menu to save the scanned image.
For the details on Adobe Acrobat 5.0 operations, refer to the Adobe Acrobat 5.0 manual and
Help.
fi-4220C Image Scanner Operator’s Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
If you save scanned documents using this procedure, the file size
may increase. For reducing the file size, please follow the procedure
below. (It may take more time than usual)
HINT
1. Select [File (F)] - |[Print (P)...].
2. On the following dialog specify [Acrobat Distiller] for [Name].
3. Press the [Properties] button.
4. Press the [Adobe PDF settings] tab.
5. Select [Conversion Settings] to [Print].
The following shows an example of [Screen].
.
6. Click [OK] when finishing setup.
7. Enter a file name and click the [Save] button on the [Save PDF
File As] dialogbox.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
2.6 Excluding a Color in the Image (dropout color)
2.6 Excluding a Color in the Image (dropout color)
A selected color (primary colors: red, green or blue) can be removed (dropped out) from the
scanned image data.
For example, if the document contains black text in a green frame, you can set the scanner to read
only the text and eliminate (drop out) the green frame.
To set the scanner to drop out a color, change the settings in the [TWAIN Driver] dialogbox before
scanning.
1. Click the [Advance...] button in the [TWAIN Driver] dialog box.
2
⇒ The [Advance] dialog box appears.
fi-4220C Image Scanner Operator’s Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select the color to be drop out from [Dropout Color] under [More].
For example, if the document contains black text in green frame, select [Green] so that the
scanner only reads the text and eliminates the frames.
3. Click the [OK] button.
The [TWAIN Driver] dialog box will be redisplayed. Continue scanning from this dialog
box.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Detecting Double-feeds
2.7 Detecting Double-feeds
"Double-feed" is a feeding error that occurs when two or more sheets in the ADF paper chute are
fed simultaneously into the scanner.
You can set the scanner to detect double-feed, stop scanner operation, and display an error mes-
sage.
To set the scanner to detect double-feed, change the settings in the [TWAIN Driver] dialog box.
1. Click the [Option...] button in the [TWAIN Driver] dialog box.
2
⇒ The [Option] dialog box appears.
fi-4220C Image Scanner Operator’s Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Click the [Job/Cache] tab.
3. Select the detection conditions from "Double Feed" under "ADF Option".
The following detection conditions are provided:
None
: Double-feed detection is not performed.
Check thickness
: The scanner monitors the thickness of documents. It detects a dou-
ble-feed by differences in document thickness when two or more
document sheets are fed overlapping.
Check length
: The scanner monitors the length of documents. It detects a double-
feed by changes in the document length when two or more document
sheets are fed overlapping.
Check thickness and length:
The scanner monitors both document thickness and length to detect
double-feed.
Furthermore, see "6.5 Double-feed Detection Conditions" (page. 95) for detailed informa-
tion about the document for double-feed detection.
4. Click the [OK] button.
The display returns to the [TWAIN Driver] dialog box. Continue scanning from this dialog
box.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
DAILY CARE
This chapter describes how to clean the scanner.
3
When cleaning the scanner, turn off the power, and unplug the AC cable from the outlet.
3.2 Cleaning the Flatbed........................................................................................ 45
fi-4220C Image Scanner Operator’s Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Cleaning Materials and Locations requiring
Cleaning
■ Cleaning Materials
The table below shows the cleaning materials that are used on this scanner.
Cleaning Materials
Part No.
Remarks
1 bottle (100 ml)
Moisten cloth with this fluid and
wipe the scanner clean.
Cleaner F1
(or isopropyl alcohol)
CA99501-0013
Soft, dry cloth
-
-
For details on Cleaner F1, consult the agent where you bought your scanner.
■ Locations and Cycle for Cleaning
Location
Pad ASSY
Standard Cleaning Cycle
Clean every 1000 scanned sheets.
Pick roller
Feed roller
Plastic roller
White stripe
Glass
Document holding pad
Document bed
The scanner must be cleaned more frequently when the following docu-
ments are used:
ATTENTION
• Documents of coated paper
• Documents with printed text or graphics almost covering the entire surface
• Chemically treated documents such as carbonless paper
• Documents containing a large amount of calcium carbonate
• Documents with Handwritten documents
44
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Cleaning the Flatbed
3.2 Cleaning the Flatbed
• Detergent for cleaning windows or glass cleaner can be used instead of
ATTENTION
cleaning fluid. However, do not use paint thinner or other organic solvents.
■ Cleaning the Flatbed
3
The following parts needs to be cleaned in the Flatbed area:
• Document holding pad
• Document bed
Document holding pad
Document bed
fi-4220C Image Scanner Operator’s Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Open the document cover.
2. Clean the following locations using a soft, dry cloth moistened with cleaning fluid.
Document holding pad
Document bed
•
•
Document holding pad
Wipe gently.
Document bed
Wipe lightly.
Do not allow moisture to get inside the device during cleaning.
ATTENTION
3. Wait for cleaned parts to dry.
4. Gently close the document cover.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Cleaning the ADF
3.3 Cleaning the ADF
As a Guideline, clean the ADF every 1,000 scanned sheets. Note that this guideline varies accord-
ing to the type of documents you scan. For example, it may be necessary to clean the ADF more
frequently if documents are scanned when the toner is not sufficiently fixed on the printout.
• The glass surface inside the ADF becomes hot during the operation of the scanner.
Before you start to clean the inner parts of the scanner, disconnect the AC adapter from the
power outlet, and wait at least 15 minutes to let the glass cool down.
• When you perform cleaning, make sure that the inside of the scanner is free of any foreign
object, and be careful not to get your hand or the cloth caught on the pick spring (metal
part) as a deformed pick spring (metal part) may cause injury.
3
■ Cleaning the ADF
1. Open the ADF by pushing on the ADF button and turning the ADF cover to the front.
The front portion
ADF button
Be careful, the ADF cover may close and pinch your finger.
fi-4220C Image Scanner Operator’s Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Clean the following locations with a soft, dry cloth moistened with Cleaner F1.
Feed rollers (Four pieces)
White Stripe
Pad ASSY
Pick roller (One pieces)
Plastic rollers (Four pieces)
Glass (Two parts)
•
Pad ASSY
Wipe the pad assy downwards. When cleaning the pad assy, be careful not to get your
hand or the cloth caught on the pick spring (metal part).
Pick spring (metal part)
*Gray part
The portion to clean
48
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Cleaning the ADF
•
Pick roller
In step 2, all the Feed rollers turn at the same time. When cleaning the Feed rollers
positioned in the lower part of the ADF, be caereful not to touch the other Feed rollers.
Mylar sheet (Transparent)
3
•
Feed roller
1) Open the ADF by pushing on the ADF button.
If you open the ADF cover when the indication of the Function No. display is "P"
or "0", the Feed rollers do not rotate even you perform the operation of step 2)
below. So open the ADF cover when the indication is not "P" or "0".
2) Simultaneously hold down the "Send to" and "Scan" buttons on the operator panel.
The Feed rollers start to rotate slowly.
The location of "Send to" and "Scan" buttons are shown in the following illustra-
tion.
3) Hold a soft, dry cloth moistened with cleaning fluid against the surface of the rotat-
ing Feed rollers so that it lightly cleans the surface of the rollers. Take particular
care when cleaning these rollers as black debris matter on these rollers affects doc-
ument pick performance.
As a guideline, seven presses of the "Send to" and "Scan" buttons make the Feed
rollers to rotate one full turn.
Function No.
display
Function
Send to
Scan
Power button
LED
fi-4220C Image Scanner Operator’s Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Plastic roller
Clean lightly the surface of these rollers to avoid damaging it. Take particular care
when cleaning these rollers as black debris matter on it affects document pick perfor-
mance. Be careful no to damage the sponges beside the rollers.
In step 2, all the Feed rollers turn at the same time. When cleaning the Feed rollers positioned
in the lower part of the ADF, be caereful not to touch the other Feed rollers.
•
White stripe
Clean lightly.
•
Glass
Clean lightly.
If the glass or the white stripe are dirty, vertical black streaks may apper
in the scanned images.
HINT
3. Press down on the center of the ADF to return it to its original position until the ADF
button locks.
Press center of
ADF
When the ADF has returned to its original position, make sure that it is
ATTENTION
completely closed. Paper jams or feeding errors may occur if the ADF is
not closed completely.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
REPLACING CONSUMABLES
This chapter describes how to replace scanner consumables.
In this chapter Windows XP screenshots are illustrated.
The screens and operations may differ slightly if the OS that you are using is other than Windows
XP.
Also, when FUJITSU TWAIN32 or FUJITSU ISIS is updated the screens and operations noted in
this chapter will differ slightly.
4
Turn off the power and unplug the AC adapter from the outlet before changing the scanner’s
consumable products.
4.1 Consumable and Replacement Cycle ............................................................ 52
fi-4220C Image Scanner Operator’s Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
The following table shows the specifications of consumables and their standard replacement cycle.
Description
P/N
Standard Replacement Cycle
Pad ASSY
Pick roller
PA03289-0003
PA03289-0001
50,000 sheets or one year
100,000 sheets or one year
The replacement cycles above are rough guidelines for the case of using A4/Letter woodfree or
wood containing paper 64 g/m2 (17 lb). This cycle varies according to the type of the used paper
and how frequently the scanner is used and cleaned.
Use only the specified consumables. Do not use other consumables.
ATTENTION
52
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
■ Guidelines for Consumable Replacement Cycle
With this product, you can learn how many times the consumables are used so that you can esti-
mate the right timing for the replacement.
1. When turning on the power, check that the scanner is connected to the PC.
Refer to "2.2 Connecting the Scanner to a PC" in fi-4220C Getting Started on the Setup CD-
ROM for information about connecting the scanner to a personal computer.
2. Double click the "Printer and Other Hardware" icon on the operator panel of the host
computer.
4
⇒ The [Printer and Other Hardware] screen is displayed.
fi-4220C Image Scanner Operator’s Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
3. In the [Printer and Other Hardware] screen, double click the "Scanners and Cameras"
icon.
⇒ The [Scanners and Cameras] screen is displayed.
4. Right click the "fi-4220Cdj", and select [Properties] from the menu.
(For Windows 95 and WindowsNT 4.0, select the [FUJITSU TWAIN 32] icon and click the
[Properties] button.)
⇒ The [fi-4220Cdj Properties] dialog box appears.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
4.1 Consumable and Replacement Cycle
4
5. Click the "Device Set" tab.
⇒ The following screen is displayed.
You can confirm the following information in this panel:
•
•
•
Total number of scans
Pad counter (approximate number of scans after resetting the pad counter)
Pick roller counter (approximate number of scans after resetting the Pick roller counter)
fi-4220C Image Scanner Operator’s Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
The following message sometimes appears when the scanner is being used:
Replace consumables when this message is displayed.
■ When Replacing Consumables Immediately
1. To replace consumables after completing the scanning of all the document sheets in the ADF,
click the [Ignore] button.
To abort scanning and replace the consumables immediately, click the [Cancel] button.
2. Replace the consumables.
3. To disable display of this message, mark the "This message not display again" checkbox.
Note that when the "This message not display again" checkbox is marked, this message is not
displayed until the consumables counter is reset.
■ When Consumables Cannot Be Replaced Immediately
1. To continue scanning of the current document, click the [Ignore] button.
To discontinue scanning, click the [Cancel] button.
2. Replace the consumable as soon as possible.
3. To disable display of this message, mark the "This message not display again" checkbox.
Note that when the "This message not display again" checkbox is marked, this message is not
displayed until the consumables counter is reset.
To display the message again after scanning 100 sheets, mark the [Warms again after scanning
100 pages] checkbox.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Replacing the Pad ASSY
4.2 Replacing the Pad ASSY
The Pad ASSY consists of the following 2 parts:
Pad ASSY
Sheet-Guide
1. Remove any documents on the ADF paper chute. And remove the ADF paper chute.
2. Open the ADF by pushing the ADF button.
4
The front portion
ADF button
Be careful, the ADF cover may close and pinch your finger.
3. Remove the Pad ASSY.
Press the knobs on both ends of the Pad ASSY, and pull the Pad ASSY upwards and towards
you.
When doing this, take care not to catch the pick springs.
Pick spring
fi-4220C Image Scanner Operator’s Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach the new Pad ASSY.
Hold both ends of the new Pad ASSY and attach it to its installation location.
When doing this, take care not to catch the pick springs.
Make sure that the Pad ASSY is firmly attached. When the Pad ASSY is
ATTENTION
not correctly attached, document jams or other feeding errors may occur.
5. Replace the Sheet-guide.
Grip the knobs on the Sheet-guide, and lift it up to remove. And attach the new Sheet-guide.
6. Attach the ADF paper chute.
Press down on the center of the ADF to return it into its original position and lock the ADF
button.
Press center of
ADF
58
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Replacing the Pad ASSY
7. Reset the pad counter.
For Windows 98 / Windows Me / Windows 2000 / Windows XP
•
1) When turning on the power, check that the scanner is connected to your PC.
2) Open the [Scanners and Cameras] from the control panel of your PC.
3) Open the [Properties] of [fi-4220Cdj] from the [Scanners and Cameras].
4) The [fi-4220Cdj Properties] dialogbox appears.
5) Click the "Device Set" tab. The following panel appears.
⇒ The following screen is displayed.
4
After clicking the [Clear] button beside the "Pad Counts" in "Page Counter", click
the [OK] button.
This returns the pad counter to "0".
fi-4220C Image Scanner Operator’s Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
•
For Windows 95 / Windows NT 4.0
1) When turning on the power, check that the scanner is connected to your PC.
2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray,
then select "Option".
3) Double click "Scanner Information".
⇒ The following screen is displayed.
4) Click the "Pad Counts Reset" button.
⇒ The following message is displayed.
Click "Yes".
The Pad counter returns to "0".
60
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
4.3 Replacing the Pick Roller
1. Remove any documents on the ADF paper chute.
2. Remove the ADF paper chute.
ADF paper chute
4
3. Open the ADF by pushing the ADF button.
The front portion
ADF button
Be careful, the ADF cover may close and pinch your finger.
fi-4220C Image Scanner Operator’s Guide
61
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove the Pick roller from the scanner.
1) Grip the knobs on the sheet guide with your fingers, and lift it up to remove.
2) Rotate the Pick roller bushing in the direction of the arrow.
Pick roller bushing
3) Remove the Pick roller while lifting it up in the direction of the arrow.
The Pick roller Bushing is hard. Do not turn this bearing with your fingernails.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
5. Remove the Pick roller from the shaft while lifting up the tab on the Pick roller.
Shaft
tab
Lift up
Pull shaft to remove
6. Attach the new Pick roller.
Insert the new Pick roller aligning the protrusion on the shaft with the slot for the screw in
the Pick roller.
4
Protrusion
Slot
Make sure that the Pick roller is completely attached. An incompletely
attached Pick roller might cause document jams or other feed errors.
When attaching the Pick roller, make sure that the roller clicks in to
place
ATTENTION
"Click"
fi-4220C Image Scanner Operator’s Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Attach the Pick roller to the scanner.
Attatch the Pick roller to the scanner in reverse order of the procedure for removing.
1) Turn the Pick roller bushing in the direction indicated by the arrow.
Pick roller bushing
2) Move the sheet guide claws in the direction indicated by the arrow to fix the sheet guide.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
8. Press down the center of the ADF to return it to its original position and lock the ADF
button.
Press center of
ADF
4
9. Attach the ADF paper chute.
ADF paper chute
fi-4220C Image Scanner Operator’s Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Reset the pick counter.
For Windows 98 / Windows Me / Windows 2000 / Windows XP
•
1) When turning on the power, check that the scanner is connected to your PC.
2) Open the [Scanners and Cameras] from the control panel of your PC.
3) Open the [Properties] of [fi-4220Cdj] from the [Scanners and Cameras].
4) The [fi-4220Cdj Properties] dialogbox is displayed.
5) Click the "Device Set" tab.
⇒ The following panel appears.
After clicking the [Clear] button beside the "Pick Roller Counts" in "Page
Counter", click the [OK] button.
This returns the pick counter to "0".
66
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Replacing the Pick Roller
•
For Windows 95 / Windows NT 4.0
1) When turning on the power, check that the scanner is connected to your PC.
2) Right click the "FUJITSU Scanner Control Center" icon displayed in the task tray,
then select "Option".
3) Double click "Scanner Information".
⇒ The following screen is displayed.
4
4) Click the "Pick Roller Counts Reset" button.
⇒ The following message is displayed.
Click "Yes".
The Pick counter (The Pick roller counts) returns to "0".
fi-4220C Image Scanner Operator’s Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5
TROUBLESHOOTING
This chapter describes how to remedy document jams, other trouble, items to check before contact-
ing the agent where you bought the scanner, and how to check device labels.
About troubles that are not described here, and the details of the errors,
ATTENTION
refer to the FUJITSU TWAIN32 Scanner Driver Help on the Setup CD-
ROM.
5
5.1 Removing Jammed Documents...................................................................... 70
5.4 Checking Labels on the Scanner.................................................................... 87
fi-4220C Image Scanner Operator’s Guide
69
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Removing Jammed Documents
If a document jam occurred, follow the procedure below to remove the jammed documents.
• Take care not to get injured when removing jammed documents.
• Be careful not to get neckties, necklaces, etc. entangled in the scanner when removing the
jammed documents
• The surface of the glass may become hot during operation. Take care not to get burned.
1. Remove any documents on the ADF paper chute.
2. Open the ADF by pushing on the ADF button.
The front portion
ADF button
Be careful, the ADF cover may close and pinch your finger.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
5.1 Removing Jammed Documents
3. Remove the jammed document.
• Staples, paper clips, etc. cause document jams. Be sure to fully
check the document and feed path, and remove any small metal
objects such as these.
ATTENTION
Also, before you start scanning, be sure to remove any staples,
clips, etc. from the document.
• Take care not to pull the pick springs when removing jammed doc-
uments.
4. Press down on the center of the ADF to return it to its original position and lock the
ADF button.
Press center of
ADF
5
Make sure that the ADF is completely closed. When it is not com-
ATTENTION
pletely closed, document jams or feeding errors may occur.
When the scanning is completed or canceled, the documents might
ATTENTION
remain inside the ADF even though any error message is not dis-
played.
Follow the procedure below to remove the documetns remaining in the
ADF.
1. Remove all documents from the ADF paper chute.
2. Open the ADF by pushing down the ADF button.
3. Remove the remaining documents.
4. Push in the center of the ADF to close it until the ADF button is
locked.
fi-4220C Image Scanner Operator’s Guide
71
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
This section describes troubles that may occur during scanning and how to remedy that trouble.
Before you ask for repair, check the following flowcharts.
If the remedies in these flowcharts do not solve the problem, check the items in "5.3 Items to
the agent where you bought the scanner.
Scanner does not turn ON.
Symptom 1
NO
Are power cable and AC adapter
correctly connected?
Correctly connect power cable.
YES
NO
Have you pushed the power
button?
Press power button.
YES
Contact the manufacturer’s
authorized service center.
72
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Indication on Function No. display goes out.
Symptom 2
Scanner is in Power Save
mode. Press any button on
control panel to start up
scanner.
YES
NO
Has a long time passed since
you used the scanner for the
last time?
NO
Scanner operation is
normal.
Does the display remain blank
even after you have turned on
the power again?
YES
Contact the manufacturer's
authorized service center.
5
fi-4220C Image Scanner Operator’s Guide
73
Download from Www.Somanuals.com. All Manuals Search And Download.
The scanning does not start.
Symptom 3
NO
Set the shipping lock to
correctly position.
Is the shipping lock set at operating
position?
YES
NO
NO
NO
Are the document loaded correctly
on the ADF paper chute?
Load document correctly on
ADF paper chute.
YES
Is the ADF closed completely?
Remove all documents from
the ADF paper chute. Then
open and close the ADF.
YES
Is the interface cable connected
correctly?
Connect interface cable
correctly.
YES
NO
NO
(when using scanner on SCSI
interface)
Is the SCSI ID set correctly?
Set SCSI ID correctly by
SCSI ID switch on rear of
scanner.
YES
Does the Function No. display
indicates any alarm?
The scanner operation is
normal.
YES
The scanner operation is
normal.
Does the alarm state remain
displayed even after the scanner
has been turned off and on
again?
NO
YES
Contact the manufacturer's
authorized service center.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Quality of scanned pictures or photos is
not satisfactory.
Symptom 4
NO
Is halftoning or dithering selected?
Select halftoning or dithering
on your PC.
YES
Are the document glass, document
press pad, glass, and white stripe
clean?
NO
Clean dirty locations. (*)
YES
Contact the manufacturer’s
authorized service center.
5
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page.
43).
Quality of scanned text or lines is unsatisfactory.
Symptom 5
NO
Are the document glass, document
press pad, glass, and
Clean dirty locations. (*)
White stripe clean?
YES
Contact the manufacturer’s
authorized service center.
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page.
43).
fi-4220C Image Scanner Operator’s Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Images are distorted or blurred.
Symptom 6
Are the document glass, document
press pad, glass, and white stripe
clean?
NO
Clean dirty locations. (*)
YES
YES
Is the ADF cover pressed down or
heavy object placed on the ADF
during scanning?
Do not press down ADF or
place heavy objects on ADF
during scanning.
NO
YES
Is something causing the scanner
to vibrate during scanning with the
ADF?
Do not allow anything to
cause the scanner to
vibrate while scanning.
NO
Is the scanner not installed on a
flat, level surface or is a scanner’s
rubber foot missing?
NO
Install scanner on flat, level
surface or attach rubber foot.
YES
Contact the manufacturer's
authorized service center.
*) For details on how to clean dirty locations, see "Chapter 3 DAILY CARE" (page.
43).
76
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Vertical lines appear in the scanned image.
Symptom 7
YES
YES
YES
Is the document scanned on
the flat bed?
Contact the manufacturer’s
authorized service center.
NO
Are lines white ?
Clean the white stripe beside
the glass. (*)
NO
Are the lines black?
Clean glass. (*)
NO
5
Contact the manufacturer’s
authorized service center.
*) For cleaning the white part beside the glass and for cleaning the glass, refer to "3.3
fi-4220C Image Scanner Operator’s Guide
77
Download from Www.Somanuals.com. All Manuals Search And Download.
The Function No. display indicates alarm after
the scanner is turned ON.
Symptom 8
NO
NO
Is the shipping lock set at operating
position?
Set the shipping lock to
correct position.
YES
Turn the scanner OFF and then ON
again.
Does the Function No. display still
indicates the alarm?
The scanner operation is
normal.
YES
Contact the manufacturer's
authorized service center.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Does double-feed occur frequently?
Symptom 9
Do the documents satisfy
conditions described under the
"Precautions" in "6.2 Document
Paper Quality"?
NO
NO
Use documents that satisfy
the requirements. (*1)
YES
Fulfill the double-feed
detection conditions. (*2)
When the double-feed detection is
ON, are the double-feed detection
conditions fulfilled? (*2)
YES
Fan the document before
loading, or reduce number
of sheets of the documents.
NO
YES
NO
Were the documents fanned before
loaded into the ADF paper chute?
YES
Fan the documents 3 or 4
times to remove static
electricity from the paper.
Have the documents just been
printed out on a copier or laser
printer?
5
NO
Reduce the number of sheets
of the document.
Is the document stack 5 mm
or less?
YES
Continued on next page
fi-4220C Image Scanner Operator’s Guide
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Continued from previous page
NO
Attach the Pad ASSY
correctly. (*4)
Is the Pad ASSY attached
correctly?
YES
YES
YES
Clean the Pad ASSY. (*3)
Replace the Pad ASSY. (*4)
Is the Pad ASSY dirty?
NO
Is the Pad ASSY worn out?
NO
Contact the manufacturer's
authorized service center.
*1) For details on requirements, see "6.2 Document Quality" (page. 91).
*2) For details on double-feed, see "6.5 Double-feed Detection Conditions" (page. 95).
*3) For details on how to clean Pad ASSY, see "3.3 Cleaning the ADF" (page. 47).
*4) For details on how to replace and attach Pad ASSY, see "4.2 Replacing the Pad
80
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Do pickup errors occurs frequently?
Symptom 10
Do the documents satisfy the
conditions described under "
Precautions" in "6.2 Document
Paper Quality"?
NO
NO
Use document which is
satisfying requirements.
(*1)
YES
Fan the document before
loading, or reduce the number
of sheets of the documents.
Were the documents fanned
before loading on ADF paper
chute?
YES
NO
Attach the Pad ASSY
correctly. (*2)
Is the Pad ASSY attached
correctly?
YES
YES
Clean the Pick roller. (*3)
Replace the Pick roller. (*4)
Is the Pick roller dirty?
5
NO
YES
Is the Pick roller worn out?
NO
Contact the manufacturer's
authorized service center.
*1) For details on requirements, see "6.2 Document Quality" (page. 91).
*2) For details on how to attach the Pad ASSY, see "4.2 Replacing the Pad ASSY"
*3) For details on how to clean the Pick roller, see "3.3 Cleaning the ADF" (page. 47).
*4) For details on how to replace the Pick roller, see "4.3 Replacing the Pick Roller"
fi-4220C Image Scanner Operator’s Guide
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Paper jams occur frequently?
Symptom 11
Do the documents satisfy the
conditions described under "
Precautions" in "6.2 Document
Paper Quality"?
Use the document that
satisfy the requirements. (*1)
NO
YES
YES
Clean the ADF or remove any
foreign objects. (*2)
Is there any objects in the ADF?
NO
NO
Is the Pad ASSY attached
correctly?
Attach the Pad ASSY
correctly. (*3)
YES
Contact the manufacturer's
authorized service center.
*1) For details on requirements, see "6.2 Document Quality" (page. 91).
*2) For details on how to clean the ADF, see "3.3 Cleaning the ADF" (page. 47).
*3) For details on how to attach the Pad ASSY, see "4.2 Replacing the Pad ASSY"
82
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Remedying Typical Troubles
Are the scanned images elongated?
Symptom 12
NO
Have you cleaned all the
rollers?
Clean all of the rollers. (*)
YES
Contact the manufacturer’s
authorized service center.
YES
Have you adjusted the scan
scale?
NO
Set the scan scale.
Which OS do you use?
Windows 95/
Windows NT 4.0
Windows 98/
Windows Me/
Windows 2000/
Windows XP
5
YES
Display the properties of
the scanner that you are
using on "Scanners and
Cameras" in the control
panel, then adjust the
scan scale.
Is the Scanner Control Center
icon displayed in the task tray?
NO
Select [FUJITSU Scanner Control
Center] from the Start menu and
run it.
Right click the Scanner
Control Center icon and select
[Options] then adjust the scan
scale.
*) For details on how to clean the rollers, see "3.3 Cleaning the ADF" (page. 47).
fi-4220C Image Scanner Operator’s Guide
83
Download from Www.Somanuals.com. All Manuals Search And Download.
Is there a shadow on the leading edge of the
scanned image?
Symptom 13
YES
Did you adjust the offset
(Position to start scanning
the document)?
Contact the manufacturer’s
authorized service center.
NO
Adjust the offset.
Which OS do you use?
Windows 95/
Windows 98/
Windows NT 4.0
Windows Me/
Windows 2000/
Windows XP
YES
Is the Scanner Control Center
icon displayed in the task tray?
Display the properties of
the scanner that you are
using on "Scanners and
Cameras" in the control
panel, then adjust the
[Sub-scan Setting].
NO
Select [FUJITSU Scanner Control
Center] from the Start menu and
run it.
Right click the Scanner
Control Center icon and
select [Options] then
adjust the [Sub-scan Setting].
84
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Items to Check Before Contacting the Agent Where You Bought the Scanner
5.3 Items to Check Before Contacting the Agent
Where You Bought the Scanner
Check the following items before you contact the agent where you bought the scanner.
■ General Details
Item
findings
Model
(Example) fi-4220C
For details on model, see "5.4 Checking Labels on
Serial No.
(Example) 000001
For details on serial No., see "5.4 Checking Labels
Production date
(Example) 2003-9 (September, 2003)
For details on production date, see "5.4 Checking
Date of purchase
Symptom
5
Frequency of trouble
■ Installation or PC connection issues
■ Problem at the time of personal computer connection
Item
findings
OS (Windows)
Displayed error message
Application
(Example) SCSI interface
Interface controllers
(Example) made by Adaptec
SCSI Card 2940Au
fi-4220C Image Scanner Operator’s Guide
85
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Feed system trouble
Item
findings
Document type
Main purpose of use
Last cleaning date
Last consumables replacement date
Operator panel status at trouble
■ Imaging system trouble
Item
findings
Type and version of scanner driver
Type of interface controller
(Example) made by Adaptec
SCSI Card 2940Au
OS (Windows)
Application software
(Example) ScandAll 21
(Example) Acrobat
■ Other
Item
findings
Can both the original document and scan-
ner image be sent by e-mail or Fax?
86
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4 Checking Labels on the Scanner
5.4 Checking Labels on the Scanner
This section describes how to check the labels on the scanner.
■ Positions of Labels on the Scanner
The following shows where the two labels are located on the scanner.
Label B
Label A (example): Indicates scanner information.
Label A
5
2003 - 09
Label B (example): Indicates various standards that the scanner conforms with.
fi-4220C Image Scanner Operator’s Guide
87
Download from Www.Somanuals.com. All Manuals Search And Download.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2 Document Quality
6.2 Document Quality
■ Document Type
The following paper types are recommended for document use:
6
• Woodfree paper
• Wood containing paper
When using documents of paper type other than the above, check whether or not the document can
be scanned by test-scanning a few sheets before executing the actual document.
■ Document Thickness
Paper thickness is expressed by "paper weight." The following shows the paper weights that can be
used on this scanner:
• 52 g/m2 to 127 g/m2
Only paper weight of 127 g/m2 is acceptable for A8-size documents.
■ Precautions
The following documents may not be scanned successfully:
• Documents of non-uniform thickness (e.g. envelopes)
• Folded or torn documents
• Tracing paper
• Coated paper
• Carbon paper
• Carbonless paper
• Photosensitive paper
• Perforated or punched documents
• Documents that are not square or rectangular
• Very thin documents
Do not use the following documents:
• Paper-clipped or stapled documents
• Documents on which the ink is still wet
• Documents smaller than A8 (Portrait) in size
• Documents wider than A4 or Letter size (216mm)
• Documents other than paper such as fabric, metal foil, or transparencies
fi-4220C Image Scanner Operator’s Guide
91
Download from Www.Somanuals.com. All Manuals Search And Download.
• When scanning semi-transparent documents, set the density to light to
avoid bleed through.
HINT
• To prevent the rollers from becoming dirty, avoid scanning documents con-
taining large areas written or filled in pencil. If scanning of such documents
is unavoidable, clean the rollers frequently.
• Carbonless paper contains chemical substances that may damage the
Pad ASSY or rollers (e.g. Pick roller) when documents are fed. Pay atten-
tion to the following:
ATTENTION
Cleaning:
If pick errors occur frequently, clean the Pad ASSY and
Pick rollers.
For details on cleaning the Pad ASSY and Pick rollers,
Replacing parts: The service life of the Pad ASSY and Pick rollers is
sometimes shortened when scanning medium-grade
paper documents.
• When the manuscript of Wood containg paper is read, the life of a Pad
ASSY and a Pick roller may become short compared with the case where
the manuscript of Woodfree paper is read.
When using the ADF, the leading edge of all document sheets must be
evenly aligned. Make sure that curling at the leading edge is within the fol-
lowing tolerances:
HINT
More than 30mm
Feed direction
Less than
3mm
Top of the paper
Read surface
Feed direction
More than 30mm
Less than
5mm
Top of the paper
Read surface
92
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Maximum Document Loading Capacity
6.3 Maximum Document Loading Capacity
The maximum number of sheets that can be loaded on the ADF paper chute is determined by the
size and weight of the document. The following graph shows the maximum document loading
capacity of ADF according to paper weight.
6
60
60
A4 / Letter or smaller
Legal
50
41
50
50
40
30
20
Capacity of ADF
(number of
pages)
35
29
29
24
0
52 64
80
104
127
Paper weight (g/m2 )
Paper weight conversion table
Conversion
Unit
2
52
14
64
17
75
20
80
21
90
24
104
28
127
34
g/m
lb
fi-4220C Image Scanner Operator’s Guide
93
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 Area not to be perforated
When using the ADF, document trouble might occur if there are punched holes in the shaded area
in the following figure. If hole-punched documents must be scanned, use the Flatbed.
35
Read reference
position
Top of paper
Front side
Feeding
direction
Bottom of paper
(Unit : mm)
Center of paper
94
Download from Www.Somanuals.com. All Manuals Search And Download.
6.5 Double-feed Detection Conditions
6.5 Double-feed Detection Conditions
There are three double-feed detection modes: document thickness, document length, and both doc-
ument thickness and length. The following conditions must be satisfied in each of these detection
modes.
6
■ Detection by Document Thickness
Sheets of the same thickness shall be set in the ADF at a time.
• Document thickness: 0.065 to 0.15mm
• Printed area: 12% or less
• No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
• Punched holes are not allowed within 35mm of the vertical center line of the document.
• The deviation in the amount of the light transmitted through background areas must not be
less than 10%.
■ Detection by Document Length
Sheets of the same length shall be set in the ADF at a time.
• Document length deviation: 1% or less
• Punched holes are not allowed within 35mm of the vertical center line of the document.
■ Detection by Document Thickness and Length
Sheets of the same thickness and length shall be set in the ADF at a time.
• Document thickness: 0.065 to 0.15mm
• Document length deviation: 1% or less
• Printed area: 12% or less
• No black printed areas are allowed at the center area (26 x 10mm) at the leading edge of the
document.
• Punched holes are not allowed within 35mm of the vertical center line of the document.
• The deviation in the amount of the light transmitted through background areas must not be
less than 10%.
fi-4220C Image Scanner Operator’s Guide
95
Download from Www.Somanuals.com. All Manuals Search And Download.
The type of document and document conditions sometimes cause the dou-
ble-feed detection rate to drop.
HINT
35mm
26mm
10mm
No printing allowed
Feeding direction
No punched holes
allowed
Center of paper
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
SCANNER SPECIFICATION
This chapter lists the scanner specifications.
7
7.2 Installation Specifications............................................................................. 100
7.3 External Dimensions...................................................................................... 101
fi-4220C Image Scanner Operator’s Guide
97
Download from Www.Somanuals.com. All Manuals Search And Download.
7.1 Basic Specifications
1
2
3
4
Scanner Type
Image sensor
Light source
ADF(Automatic Docu-
ment Feeder),Flatbed
-
CCD x 3
Front / Back /
Flatbed
Incandescent cold cath-
ode fluorescent lamp x 3
Front / Back /
Flatbed
2
Scanning
area
Minimum
Maximum
A8 (Portrait) (Note (*1))
ADF 127 g/m
paper
A4 (Flatbed) / Legal (ADF)
-
-
2
2
5
6
Paper Weight
52 g/m to 127g/m
(Note (*2))
Scanning
Speed
Binary
Simplex: 25 sheets/min.
200 dpi
150 dpi
(monochrome) Duplex: 25 sides/min.
(Note (*4))
(A4 Portrait)
(Note (*3))
Color
Simplex: 25 sheets /min.
Duplex: 25 sides/min.
(Note (*4))
2
7
Capacity of ADF
50 sheets
A4, 80 g/m
(Note (*5))
8
9
Optical Resolution
600 dpi
-
Output reso- Binary
50 - 600 dpi
Scalable in 1
lution
(monochrome)
dpi increments
Grayscale
Color
50 - 600 dpi
50 - 600 dpi
8 bits per color
Scalable in 1
dpi increments
Scalable in 1
dpi increments
10
Grayscale level
(internal)
Internal 10 bits
11
12
Halftone Patterns
Dither / error diffusion
SCSI-2
-
Interface
Shield-type 50
pin (pin-type)
halfpich
(Note (*6))
USB 1.1
B type
-
13
Other function
JPEG compression
98
Download from Www.Somanuals.com. All Manuals Search And Download.
7.1 Basic Specifications
*1) The minimum size for scanning is A8 when using the ADF. When using the Flat-
bed to scan the minimum scanning range is virtually unlimited.
*2) The manuscript thicknesses noted are for when using the ADF. When using the
Flatbed to scan the manuscript thickness is unlimited.
For details, see "Chapter 6 ADF AND PAPER SPECIFICATION" (page. 89).
*3) The scanning speed is the maximum speed of the scanner hardware. Software pro-
cessing time such as data transfer time is added to the actual scanning time.
*4) The scanning speed noted is the value when using the ADF to scan.
*5) The maximum stacking capacity varies according to the document thickness. For
details, see "Chapter 6 ADF AND PAPER SPECIFICATION" (page. 89).
*6) The SCSI-2 and USB1.1 interfaces cannot be used at the same time.
7
fi-4220C Image Scanner Operator’s Guide
99
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 Installation Specifications
Item
Specification
Width
Dimensions (mm)
Depth
Height
(Without ADF paper chute)
569 (22.4 in) 302 (11.9 in)
229 (9.0 in)
Installation Space (mm)
(D x W x H)
800 (31.5 in) x 400 (15.8 in) x 450 (17.8 in)
Weight (kg)
8 (17.7 lb)
Input
Voltage
100 to 120 VAC ±10%
220 to 240 VAC ±10%
power
Phases
Single-phase
50 / 60 ± 3Hz
34 W or less
Frequency
Power consumption
Installation Space is the reference value of an installation space
required to read A4 manuscript.
ATTENTION
Item
Specification
Ambient
condition
Device status
Temperature
Humidity
Operating
Not operating
5 to 35 °C (41 to 95°F)
20 to 80 %
-20 to 60 °C (-4 to 140°F)
8 to 95 %
Heat capacity
29.3 kcal / H or less
11.5 (25.4 lb)
Shipping Weight (kg)
100
Download from Www.Somanuals.com. All Manuals Search And Download.
102
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
A4 size
A standard paper size. Paper size is 210 x 297 mm.
A5 size
A standard paper size. Paper size is 148 x 210 mm.
A6 size
A standard paper size. Paper size is 105 x 148 mm.
A7 size
A standard paper size. Paper size is 74 x 105 mm.
A8 size
A standard paper size. Paper size is 53 x 74 mm.
ASCII
The acronym for American Standard Code for Information Interchange.
ASCII is a set of 256 codes (numbered 0 to 255) used to communicate information
between a computer and another device such as a scanner.
Backside reading = Back-side scanning
Refers to reading the backside of the document, specifically in Duplex reading mode.
Bit
The smallest unit of information in computer memory. A bit is a single digit, either a 1 or a
0, in the binary numbering system. Eight bits equal one byte.
Density
In this manual, refers to a measurement of the depth of the display.
fi-4220C Image Scanner Operator’s Guide
GL-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Dither
Technique for producing halftone images by representing the entire grayscale with only
two pixel levels, black and white.
Double feed detection
A scanner function which detects the accidental feeding of multiple sheets by the ADF
unit. Can be turned on or off by the operator.
Double Letter Size
A standard paper size used in the U.S.A. and other countries. Paper size is 11 x 17
inches.
dpi
Dots per inch.
Dropout color
A color which is used in the document but does not appear in the read image.
Duplex reading mode
A reading mode in which both sides of the document are read.
Equipment Error
An error that cannot be corrected by the operator. Call CE.
Error diffusion
High-quality halftone (pseudo-grayscale) image production based on black-and-white
pixel binarization. A pixel’s optical density and that of adjacent pixels are summed, with
black pixels relocated in their order of density as they relate to adjacent pixels.
The purpose of this technique is to minimize the average error between read and printed
densities. Density data for adjacent pixels is modified by diffusing errors on the objective
pixel into several pixels, which are then binarized. This maintains high grayscale levels
and resolution during reading, while suppressing more patterns by dotted halftone
images such as newspaper photographs.
GL-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Filtering
A correction method that improves the read quality of handwritten documents. The read
quality of images written in pencil or ball-pointed pen depends on the reflective light
characteristics of the specific ink or lead used. Dropped pixels may produce outlines,
gaps, or thin, barely connected lines due to uneven optical density. Filtering detects
areas lighter than their surroundings and increases their density to improve image clarity.
Front-side reading = Front-side scanning
Refers to reading the front side of the document, specifically in Duplex reading mode.
Halftone processing
Any method used to reproduce a photograph which includes a shade as an image com-
posed of dots, namely, a binary image. Dithering and error diffusion processing are
examples of halftone processing.
Hexadecimal
A base-16 numbering system (also commonly referred to as hex numbers). Since a
base-16 system requires 16 digits, numbers 0 through 9 and letters A through F are
used. It is convenient to express binary numbers in hexadecimal because fewer digits
are required.
Image emphasis
Density is decreased for lighter but not completely white areas adjacent to black areas.
Weakening this emphasis eliminates spot noise or produces softened images.
Image processing
An image is read with specified parameters.
Interface
The connection that allows communication from one part of a system to another. For
example, electrical signals are transferred between the computer and scanner over an
interface cable.
Inversion (Reverse-image reading)
In reverse-image reading, data is changed from black to white and vice versa.
fi-4220C Image Scanner Operator’s Guide
GL-3
Download from Www.Somanuals.com. All Manuals Search And Download.
IRAS
Initialization of the hardware.
Landscape orientation
A document is transported and read with the long side vertical to the moving direction.
Letter size
A standard paper size used in the U.S.A. and other countries. Paper size is 8-1/2 x 11
inches.
Linedrawing mode
Selecting linedrawing mode makes threshold and contrast settings effective but prevents
brightness from being set. The specified threshold value determines whether black or
white pixels are scanned. Line drawing mode is therefore appropriate for scanning text
and line art images.
Manual Feed mode = Manual Mode
Requires the operator to feed each document manually into the ADF paper chute.
Manual start mode (<-> automatic start mode)
The reading operation is activated by pressing the START button in this mode. Available
only when video option board is installed.
Mirror image
The read image is symmetrically flipped to produce a mirror image of the original
detected in the main scanning direction.
Noise removal
Isolated noise from an image appearing as black spots in white areas and voids in black
areas is removed to improve image quality.
Operator panel
A panel containing the scanner indicators and buttons. The operator panel is used to
control scanner operations such as loading document, selecting features, and changing
setup options.
GL-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Outline extraction
The boundary between black and white areas is traced and the outline extracted for
closed areas.
PAPER JAM
A warning informing the user that document is jammed in the transport unit, or that trans-
portation is disabled because the transport unit is slippery. This warning also appears
when a double feed is detected.
Photograph mode (White level follower OFF)
Selecting photograph mode makes brightness and contrast settings effective but pre-
vents the threshold from being set. With photograph mode, the darkness of image corre-
sponds to the black-pixel density, making it suitable in scanning images such as
photographs having gradations.
Photo mode = photograph mode
A photograph is read properly in this mode.
Portrait orientation
A document is transported and read with the long side parallel to the moving direction.
Read operation
Refers to the reading operation including Simplex reading and Duplex reading.
RS-232C interface
A type of serial interface. See Serial interface.
SCSI ID
Used to specify a particular SCSI device when the initiator selects a target or the target
reconnects to the initiator.
Simplex reading mode
Only the front side of the document is read in this mode. Place the documents face up at
the center of the ADF paper chute.
fi-4220C Image Scanner Operator’s Guide
GL-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Smoothing
A process that eliminates “jaggies” from slanted lines and curves. Irregular convexities
are deleted and irregular concavities filled in. This is useful in OCR applications, for
example.
Temporary Error
An error correctable by the operator.
Time-out limit
This is the time the scanner waits for next document insertion after the last document
feeding. The scanner returns Paper Empty when no document is set after time-out limit.
GL-6
Download from Www.Somanuals.com. All Manuals Search And Download.
M
O
P
Setting Window for FUJITSU TWAIN32
R
Reset
S
T
Dimensions ....................................... 100
W
IN-2
Download from Www.Somanuals.com. All Manuals Search And Download.
fi-4220C Image Scanner Operator’s Guide
P3PC-E677-02EN
Date of issuance: October, 2009
Issuance responsibility: PFU LIMITED
z Copying of the contents of this manual in whole or in part and
copying of the scanner application is forbidden under the copyright
law.
z The contents of this manual are subject to change without notice.
z PFU LIMITED. is not liable whatsoever for any damages resulting
from use of this scanner and procedures described in this manual,
profit due to defects, and any claims by a third party.
Download from Www.Somanuals.com. All Manuals Search And Download.
|