Fisher Price Motorized Toy Car L3938 User Manual

L3938  
This product is not recommended for use  
on loose dirt or wet surfaces.  
Please keep this instruction sheet for future reference,  
as it contains important information.  
Requires six “AA” (LR6) alkaline batteries (not included).  
Adult assembly is required.  
Tool required for assembly:  
Phillips screwdriver (not included).  
TM  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
1
3
Ramp Bar  
Ramp  
Spinner  
A
A
• Fit an inside track marked “A” to track marked “A”.  
• Insert three screws into the assembly and tighten.  
• Repeat this procedure to join two additional “A”  
track assemblies.  
Ramp  
Connector  
Long  
Ramp Rail  
“Snap” a ramp bar and ramp connector into one side  
of a long ramp rail.  
“Snap” the other long ramp rail to the assembly.  
4
“Snap” the ramp spinner onto the support bar.  
B
B
2
• Fit an inside track marked “B” to track marked “B”.  
• Insert three screws into the assembly and tighten.  
5
• Fit the pegs on the sides of a ramp into the holes in the  
long ramp assembly, as shown.  
Note: If the ramp does not fit, try the other ramp.  
• Repeat this procedure to build the short ramp assembly.  
• Set the ramp assemblies aside.  
• Fit the four center tracks together, as shown.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
6
2
1
9
8
3
5
6
4
7
• Each track piece has a number on the bottom. Simply match the  
numbers and fit the pieces together.  
Hint: For best performance, we suggest assembling the track on  
a hard, flat surface.  
Assembly Tip: If you cannot join all the track  
pieces together, try fitting together in three  
large sections, as shown here.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
7
15  
11  
1
1
1
16  
6
7
14  
12  
1
16  
13  
2
11  
15  
3
5
8
14  
10  
1
9
1
13  
4
1
Proper label application will help to keep the labels looking their best!  
• Make sure the areas where the labels will be applied are clean and dry. Wipe this product with a clean, soft, dry cloth to  
remove any dust or oils.  
• For best results, do not attempt to apply a label more than once.  
• Apply the labels as shown in the illustration above.  
8
“Snap” the ramp assemblies to the track.  
“Snap” the crash gate halves to the track.  
• Fit the eight track supports on to the matching posts around the track, as shown.  
Assembly is now complete.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Installation  
Battery Safety Information  
1.5V x 3  
"AA" (LR6)  
In exceptional circumstances, batteries may leak fluids  
that can cause a chemical burn injury or ruin your toy.  
To avoid battery leakage:  
• Do not mix old and new batteries or batteries of  
different types: alkaline, standard (carbon-zinc) or  
rechargeable (nickel-cadmium).  
• Insert batteries as indicated inside the  
battery compartment.  
• Remove batteries during long periods of non-use.  
Always remove exhausted batteries from the toy.  
Dispose of batteries safely. Do not dispose of the  
product in a fire. The batteries inside may explode  
or leak.  
• Never short-circuit the battery terminals.  
• Use only batteries of the same or equivalent type,  
as recommended.  
• Do not charge non-rechargeable batteries.  
• Remove rechargeable batteries from the toy  
before charging.  
• If removable, rechargeable batteries are used, they are  
only to be charged under adult supervision.  
• Locate the battery compartment on the bottom of  
each car.  
• Loosen the screw in the battery compartment door  
with a Phillips screwdriver. Remove the battery  
compartment door.  
• Insert three, new “AA” (LR6) alkaline batteries.  
Hint: We recommend using alkaline batteries for longer  
battery life.  
• Replace the battery compartment door and tighten  
the screw.  
• When sounds or motions become faint or stop,  
it’s time for an adult to change the batteries!  
Protect the environment by not disposing of this  
product with household waste (2002/96/EC).  
Check your local authority for recycling advice  
and facilities.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Race! Smash! Crash!  
1
4
• When two cars collide, the doors and hood pop open.  
To reset the car, press down on the hood area.  
• Slide the On/Off switch on the bottom of the car to on.  
2
5
• Lift the car and shake it to start the "engine" and the  
sound effects.  
Hint: For maximum distance, shake the car 7 or 8 times.  
Shaking more than this does not increase the distance it  
will travel.  
• Press the button to lower the guardrail and send a car  
crashing through the gate!  
• When you're finished, slide the On/Off switch to off.  
3
Set the cars on the starting arrow and press the pedal to start.  
• When your car stops, pick it up and shake it. Set it down  
again to resume the race.  
• Pull the handle down to reset the pedal.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Statement  
Consumer Information  
United States Only  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference  
in a residential installation. This equipment generates,  
uses and can radiate radio frequency energy and, if not  
installed and used in accordance with the instructions,  
may cause harmful interference to radio communications.  
However, there is no guarantee that interference will not  
occur in a particular installation. If this equipment does  
cause harmful interference to radio or television reception,  
which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference  
by one or more of the following measures:  
• Reorient or relocate the receiving antenna.  
• Increase the separation between the equipment  
and receiver.  
• Consult the dealer or an experienced radio/TV  
technician for help.  
Note: Changes or modifications not expressly approved by  
the manufacturer responsible for compliance could void  
the user's authority to operate the equipment.  
Care  
• Wipe with a clean cloth dampened with a mild soap and  
water solution. Do not immerse.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

Euro Pro Fryer F1400B User Manual
Exmark Lawn Mower M216KA M216KASP User Manual
Extron electronic Stereo System SY BNCM User Manual
Fiesta Gas Grill ESD45055 BC347 User Manual
GBC Binding Machine P70IX User Manual
GE Cooktop 169166 User Manual
Genius Camcorder 32300018102 User Manual
Gentek Smoke Alarm 9120 User Manual
GE Telephone 29255 Series User Manual
GE Trash Compactor GCG1500LBB User Manual