Fluke Thermometer 1529 Chub E4 User Manual

Hart Scientific

1529

Chub-E4 Thermometer Readout

User’s Guide

Rev. 5A2602

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

1 Before Y o u Start . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1

Symbols Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.2.1

1.2.2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.3

Authorized Service Centers. . . . . . . . . . . . . . . . . . . . . . 4

2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Specifications and Environmental Conditions . . . . . . . . . . 9

3.1

3.2

3.3

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Environmental Conditions. . . . . . . . . . . . . . . . . . . . . . 10

Warrant y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

4 Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Use Proper Care . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Learn About the Features and Components . . . . . . . . . . . . . 13

Connect the Probe . . . . . . . . . . . . . . . . . . . . . . . . . . 13

4.4.1

Using the Clamp-on Ferrites . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Connect the Power Source . . . . . . . . . . . . . . . . . . . . . 14

Switch the Power On . . . . . . . . . . . . . . . . . . . . . . . . 14

Measure Temperature . . . . . . . . . . . . . . . . . . . . . . . . 15

4.5

4.6

4.7

5 Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . 17

5.1

5.2

5.3

Front Panel Buttons . . . . . . . . . . . . . . . . . . . . . . . . . 17

Back Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

6 General Operation . . . . . . . . . . . . . . . . . . . . . . . . 21

Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Changing Units . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Batter y . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1

Probe Input Modules . . . . . . . . . . . . . . . . . . . . . . . . 22

6.4.1

Connecting a PRT or Thermistor Probe . . . . . . . . . . . . . . . . . . . . 23

6.4.2

Connecting a Thermocouple . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Download from Www.Somanuals.com. All Manuals Search And Download.

DC Power Source . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Power On Self-Test . . . . . . . . . . . . . . . . . . . . . . . . . 25

Display Backlight and Contrast . . . . . . . . . . . . . . . . . . . 25

Taking Measurements . . . . . . . . . . . . . . . . . . . . . . . . 25

6.8.1

Connecting the Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Enabling the Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Selecting Conversion Type and Probe Characterization . . . . . . . . . . . . 26

6.8.2

6.8.3

6.9

Fast Measurement Mode . . . . . . . . . . . . . . . . . . . . . . 26

6.10 Data Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

7 Menu Functions. . . . . . . . . . . . . . . . . . . . . . . . . . 29

7.1

Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

7.1.1

Measure Period and Fast Measurement Mode . . . . . . . . . . . . . . . . . 30

Enable Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Channel Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Moving Average. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Display Options/Auto-Cal . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Probe Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.2.1

Edit Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.2.1.1

ITS-90 Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

ITS-SR 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 9

P T -100 Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Callendar-V a n Dusen (CVD) conversion . . . . . . . . . . . . . . . . . . . . . . . . 40

RES Conversion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Thermistor T(R) Conversion [THERM-T] . . . . . . . . . . . . . . . . . . . . . . . 41

Thermistor R(T) Conversion [THERM-R] . . . . . . . . . . . . . . . . . . . . . . . 42

YSI-400 Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Thermocouple V o lts [Vin[mV]] . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

7.2.1.10 Standard Thermocouple Conversions. . . . . . . . . . . . . . . . . . . . . . . . . . 43

7.2.1.11 Thermocouple Polynomial Conversio n . . . . . . . . . . . . . . . . . . . . . . . . . 4 3

Copy Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Test Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Print Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Default Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

7.3

7.4

Fields Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

7.3.1

Clear Stat s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 8

Select Fields. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Edit Field s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1

Default Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Logging Men u . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3

7.4.1

Demand Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

7.4.1.1

Store Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Log History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

View Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Print Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Delete Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Auto Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

7.4.2.1

Logging Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Start Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

View Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

7.4.2.2

7.4.2.3

Download from Www.Somanuals.com. All Manuals Search And Download.

7.4.2.4

7.4.2.5

Print Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Delete Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

7.4.3

7.4.4

7.4.5

Log Stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Data Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Default Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

7.5

System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.5.1

Comm Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

7.5.1.1

Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

IR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

GPIB (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Date Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

System Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

8 Digital Communications Interface . . . . . . . . . . . . . . . 79

8.1

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

8.2

Communications . . . . . . . . . . . . . . . . . . . . . . . . . . 79

8.2.1

8.2.2

Serial Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

GPIB Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

8.2.2.1

Capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Device Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Interface Commands . . . . . . . . . . . . . . . . . . . . . . . . 80

8.3.1

Command Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

8.3.2

Command Syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

8.4.1

Measurement Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

8.4.1.1

CALCulate:A V ERage:CLEar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

CALCulate<chn>:A V ERage<n>:D A T A ?. . . . . . . . . . . . . . . . . . . . . . . . 88

CALCulate:A V ERage<n>:TYPE? . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

FETCh? [<chn>] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

FORMat:S T A Mp? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

FORMat:S T A Mp <bool> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

MEASure? [<chn>] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

READ? [<chn>]. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

SENSe<chn>:D A T A ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Measurement Control Commands . . . . . . . . . . . . . . . . . . . . . . . 91

8.4.2.1

INITiate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

INITiate:CONTinuous ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1

SENSe:A V ERage:COUNt? [MIN|MAX|DEF ]. . . . . . . . . . . . . . . . . . . . . 9 1

SENSe:A V ERage:COUNt <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . 91

SENSe<chn>:RESistance:RANGe? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . 91

SENSe<chn>:RESistance:RANGe <num>|MIN|MAX|DEF . . . . . . . . . . . . . 92

SENSe<chn>:RESistance:WIRE? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . 92

SENSe<chn>:RESistance:WIRE <num>|MIN|MAX|DEF . . . . . . . . . . . . . . 93

TRIGger:TIMer? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . . . . . 93

8.4.2.10 TRIGger:TIMer <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . . . . . . 93

8.4.3

Channel Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

ROUTe:CLOSe? <chn>. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

ROUTe:CLOSe <chn> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

ROUTe:OPEN? <chn> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

ROUTe:OPEN <chn >. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4

ROUTe:PRIMary? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

ROUTe:SCAN? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

ROUTe:SCAN <chn list >. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5

iii

Download from Www.Somanuals.com. All Manuals Search And Download.

8.4.3.8

8.4.3.9

ROUTe:SCAN:MODE? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . 95

ROUTe:SCAN:MODE <num>|MIN|MAX|DE F . . . . . . . . . . . . . . . . . . . . 9 5

8.4.4

Probe Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

8.4.4.1

CALCulate<chn>:CON V e rt:C A T a log ?. . . . . . . . . . . . . . . . . . . . . . . . . 9 5

CALCulate<chn>:CON V e rt:COPY <dest chn>|ALL . . . . . . . . . . . . . . . . . 96

CALCulate<chn>:CON V e rt:NAMe? . . . . . . . . . . . . . . . . . . . . . . . . . 96

CALCulate<chn>:CON V e rt:NAMe <conv> . . . . . . . . . . . . . . . . . . . . . . 96

CALCulate<chn>:CON V e rt:P A Rameter:C A T a log? . . . . . . . . . . . . . . . . . . 97

CALCulate<chn>:CON V e rt:P A Rameter:V A Lue? [<param>|ALL] . . . . . . . . . . 97

CALCulate<chn>:CON V e rt:P A Rameter:V A Lue <param>,<num>[,< param>,<num>...]

CALCulate:CON V e rt:PRINt [<chn>|ALL [,<port>]] . . . . . . . . . . . . . . . . . 98

CALCulate<chn>:CON V e rt:SNUMber? . . . . . . . . . . . . . . . . . . . . . . . . 98

8.4.4.10 CALCulate<chn>:CON V e rt:SNUMber <serl>. . . . . . . . . . . . . . . . . . . . . 98

8.4.4.11 CALCulate<chn>:CON V e rt:TEST? <res>|<volt> . . . . . . . . . . . . . . . . . . . 99

8.4.5

Calibration Coefficient Command s . . . . . . . . . . . . . . . . . . . . . . . 9 9

CALibrate:AUTo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

CALibrate<chn>:D A T E:CALibrate? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . 99

CALibrate<chn>:D A T E:CALibrate (<year>,<month>,<day>)|MIN|MAX|DEF. . . 100

CALibrate<chn>:D A T E:DUE? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . 100

CALibrate<chn>:D A T E:DUE (<year>,<month>,<day>)|MIN|MAX|DEF. . . . . . 100

CALibrate<chn>:P A Rameter:OFFSet<n>? [MIN|MAX|DEF ]. . . . . . . . . . . . 1 01

CALibrate<chn>:P A Rameter:OFFSet<n> <num>|MIN|MAX|DEF . . . . . . . . . 101

CALibrate<chn>:P A Rameter:SCALe<n>? [MIN|MAX|DEF] . . . . . . . . . . . . 101

CALibrate<chn>:P A Rameter:SCALe<n> <num>|MIN|MAX|DEF . . . . . . . . . 102

8.4.5.10 CALibrate<chn>:P A Rameter:LINearity<n>? [MIN|MAX|DEF]. . . . . . . . . . . 102

8.4.5.11 CALibrate<chn>: P A Rameter:LINearity<n> <num>|MIN|MAX|DEF. . . . . . . . 103

8.4.5.12 CALibrate<chn>:P A Rameter:RJC? [MIN|MAX|DEF ]. . . . . . . . . . . . . . . . 1 03

8.4.5.13 CALibrate<chn>:P A Rameter:RJC <num>|MIN|MAX|DEF . . . . . . . . . . . . . 103

8.4.6

Display Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

DISPlay:RESolution? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . . 104

DISPlay:RESolution <num>|AUT|MIN|MAX|DEF . . . . . . . . . . . . . . . . . 104

DISPlay:LAMP? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . . . . 104

DISPlay:LAMP <bool>|<num>|MIN|MAX|DEF. . . . . . . . . . . . . . . . . . . 104

DISPlay:DECimal:FORMat? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . 105

DISPlay:DECimal:FORMat <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . 105

DISPlay:WINDow? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . . . 105

DISPlay:WINDow <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . . . . 105

DISPlay:WINDow<n>:FIELd<n>:FEED? . . . . . . . . . . . . . . . . . . . . . . 105

8.4.6.10 DISPlay:WINDow<n>:FIELd<n>:FEED <chn>[,<num>] . . . . . . . . . . . . . . 106

8.4.7

Logging Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

LOGging:AUTomatic:DELete [<num>|ALL] . . . . . . . . . . . . . . . . . . . . 106

LOGging:AUTomatic:COUNt? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . 106

LOGging:AUTomatic:COUNt <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . 106

LOGging:AUTomatic:FREE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

LOGging:AUTomatic:LABel? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . 107

LOGging:AUTomatic:LABel <num>|MIN|MAX|DE F . . . . . . . . . . . . . . . . 1 07

LOGging:AUTomatic:POINt? [MAX] . . . . . . . . . . . . . . . . . . . . . . . . 107

LOGging:AUTomatic:PRINt [<num>|ALL [,<port>]] . . . . . . . . . . . . . . . . 108

LOGging:AUTomatic:ST A Tus? . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

8.4.7.10 LOGging:AUTomatic:S T ATus <bool> . . . . . . . . . . . . . . . . . . . . . . . . 108

8.4.7.11 LOGging:AUTomatic:TIMe? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . 108

8.4.7.12 LOGging:AUTomatic:TIMe <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . 109

8.4.7.13 LOGging:AUTomatic:V A Lue? <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . 109

8.4.7.14 LOGging:DEMand:DELete [<num>|ALL] . . . . . . . . . . . . . . . . . . . . . . 109

8.4.7.15 LOGging:DEMand:FREE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

8.4.7.16 LOGging:DEMand:LABel? [MIN|MAX|DEF ]. . . . . . . . . . . . . . . . . . . . 1 10

8.4.7.17 LOGging:DEMand:LABel <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . 110

8.4.7.18 LOGging:DEMand:POINt? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110

8.4.7.19 LOGging:DEMand:PRINt [<num>|ALL [,<port>]] . . . . . . . . . . . . . . . . . 110

8.4.7.20 LOGging:DEMand:STORe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

8.4.7.21 LOGging:DEMand:V A Lue? <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . 111

8.4.7.22 LOGging:LABel<n>:NAME?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

8.4.7.23 LOGging:LABel<n>:NAME <label >. . . . . . . . . . . . . . . . . . . . . . . . . 1 11

Download from Www.Somanuals.com. All Manuals Search And Download.

8.4.8

System Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

8.4.8.1

*IDN? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

*OPT? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

*RS T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 12

SYSTem:BOOT:VERSion? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

SYSTem:CODE:VERSion? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112

SYSTem:ERRor? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

SYSTem:SNUMber? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

SYSTem:VERSion? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

UNIT:TEMPerature? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

8.4.8.10 UNIT:TEMPerature <unit> . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113

8.4.9

Communication Interface Command s . . . . . . . . . . . . . . . . . . . . . 1 14

SYSTem:COMMunicate:IR:FEED? [MIN|MAX|DEF] . . . . . . . . . . . . . . . 114

SYSTem:COMMunicate:IR:FEED <bool>|MIN|MAX|DEF. . . . . . . . . . . . . 114

SYSTem:COMMunicate:IR:MODE? [MIN|MAX|DEF] . . . . . . . . . . . . . . . 114

SYSTem:COMMunicate:IR:MODE <num>|MIN|MAX|DEF . . . . . . . . . . . . 114

SYSTem:COMMunicate:IR:TIMe? [MIN|MAX|DEF]. . . . . . . . . . . . . . . . 115

SYSTem:COMMunicate:IR:TIMe <num>|MIN|MAX|DEF . . . . . . . . . . . . . 115

SYSTem:COMMunicate:SERial:BAUD? [MIN|MAX|DEF]. . . . . . . . . . . . . 115

SYSTem:COMMunicate:SERial:BAUD <baud>|MIN|MAX|DEF. . . . . . . . . . 115

SYSTem:COMMunicate:SERial:FDUPlex? [MIN|MAX|DEF] . . . . . . . . . . . 115

8.4.9.10 SYSTem:COMMunicate:SERial:FDUPlex <bool>|MIN|MAX|DEF. . . . . . . . . 116

8.4.9.11 SYSTem:COMMunicate:SERial:FEED? [MIN|MAX|DEF] . . . . . . . . . . . . . 116

8.4.9.12 SYSTem:COMMunicate:SERial:FEED <bool>|MIN|MAX|DEF . . . . . . . . . . 116

8.4.9.13 SYSTem:COMMunicate:SERial:LINefeed? [MIN|MAX|DEF] . . . . . . . . . . . 116

8.4.9.14 SYSTem:COMMunicate:SERial:LINefeed <bool>|MIN|MAX|DEF . . . . . . . . 117

8.4.9.15 SYSTem:COMMunicate:SERial:TIMe? [MIN|MAX|DEF] . . . . . . . . . . . . . 117

8.4.9.16 SYSTem:COMMunicate:SERial:TIMe <num>MIN|MAX|DEF . . . . . . . . . . . 117

8.4.9.17 SYSTem:KLOCkout? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . . . 117

8.4.9.18 SYSTem:KLOCkout <bool>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . . . 117

8.4.9.19 SYSTem:POWer:B A T Tery? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

8.4.9.20 SYSTem:POWer:SOURce? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

8.4.10

Date and Time Commands . . . . . . . . . . . . . . . . . . . . . . . . . . 118

8.4.10.1 DISPlay:D A T E:FORMat? [MIN|MAX|DEF ]. . . . . . . . . . . . . . . . . . . . . 1 18

8.4.10.2 DISPlay:D A T E:FORMat <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . 118

8.4.10.3 DISPlay:TIME:FORMat? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . . . 119

8.4.10.4 DISPlay:TIME:FORMat <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . 119

8.4.10.5 SYSTem:D A T E? [MIN|MAX|DEF]. . . . . . . . . . . . . . . . . . . . . . . . . . 119

8.4.10.6 SYSTem:D A T E <year>,<month>,<day> . . . . . . . . . . . . . . . . . . . . . . . 119

8.4.10.7 SYSTem:TIME ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 20

8.4.10.8 SYSTem:TIME <hour>,<minute>,<second> . . . . . . . . . . . . . . . . . . . . . 120

8.4.11

Password Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

8.4.11.1 SYSTem:PASSword:CDISable . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

8.4.11.2 SYSTem:PASSword:CENable <pass> . . . . . . . . . . . . . . . . . . . . . . . . 120

8.4.11.3 SYSTem:PASSword:CENable:S T AT e ? . . . . . . . . . . . . . . . . . . . . . . . . 120

8.4.11.4 SYSTem:PASSword:CON V e rsion? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . 121

8.4.11.5 SYSTem:PASSword:CON V e rsion <bool>|MIN|MAX|DEF . . . . . . . . . . . . . 121

8.4.11.6 SYSTem:PASSword:NEW <pass> . . . . . . . . . . . . . . . . . . . . . . . . . . 121

8.4.12

Status Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.1 *CLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.2 *ESE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.3 *ESE <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.4 *ESR? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.5 *SRE? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.6 *SRE <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.7 *STB? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

8.4.12.8 *TST? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

8.4.12.9 S T ATus:MEASure? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

8.4.12.10 S T ATus:MEASure:CONDition? . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

8.4.12.11 S T ATus:MEASure:ENABle? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

8.4.12.12 S T ATus:MEASure:ENABle <num>. . . . . . . . . . . . . . . . . . . . . . . . . . 123

8.4.12.13 S T ATus:OPERation? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

8.4.12.14 S T ATus:OPERation:CONDition? . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

8.4.12.15 S T ATus:OPERation:ENABle?[MIN|MAX|DEF] . . . . . . . . . . . . . . . . . . . 124

Download from Www.Somanuals.com. All Manuals Search And Download.

8.4.12.16 S T ATus:OPERation:ENABle <num>|MIN|MAX|DEF . . . . . . . . . . . . . . . . 124

8.4.12.17 S T ATus:QUEStionable? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

8.4.12.18 S T ATus:QUEStionable:CONDition? . . . . . . . . . . . . . . . . . . . . . . . . . 125

8.4.12.19 S T ATus:QUEStionable:ENABle? [MIN|MAX|DEF] . . . . . . . . . . . . . . . . . 125

8.4.12.20 S T ATus:QUEStionable:ENABle <num>|MIN|MAX|DEF . . . . . . . . . . . . . . 125

8.4.13

Statistical Calculation T y pes. . . . . . . . . . . . . . . . . . . . . . . . . . 126

Field Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Conversion Types and Parameter s . . . . . . . . . . . . . . . . . . . . . . . 1 28

Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Date and Time Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

9 Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . 131

9.1

PRT and Thermistor Calibration . . . . . . . . . . . . . . . . . . 131

9.1.1

PRT Calibration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . 131

PRT Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Thermistor Calibration Parameters . . . . . . . . . . . . . . . . . . . . . . 133

Thermistor Calibration Procedur e . . . . . . . . . . . . . . . . . . . . . . . 1 33

Thermocouple Calibration . . . . . . . . . . . . . . . . . . . . . 134

9.2.1

Calibration Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

9.2.2

Calibration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

10 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 137

11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 139

11.1 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 139

11.1.1

Self-Test Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 140

11.1.2

Start-up Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

11.2 Downloading Auto Logged Data . . . . . . . . . . . . . . . . . 141

11.3 Placement of IR Dongle for Transfer of Data . . . . . . . . . . . 142

11.4 CE Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

11.4.1

EMC Directiv e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 42

11.4.1.1 Immunity Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

11.4.1.2 Emission Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

11.4.2

Low V o ltage Directive (Safety) . . . . . . . . . . . . . . . . . . . . . . . . 143

11.5 Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . 143

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144

Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145

Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146

Download from Www.Somanuals.com. All Manuals Search And Download.

Figures

Figure 1 Using the Clamp-on Ferrites . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 3 Back Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 4 Thermocouple Connections . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 5 Probe Connection Wiring Diagram . . . . . . . . . . . . . . . . . . . 24

Figure 6 Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Figure 7 Measure Period. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 8 Channel Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Figure 9 Enable Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 10 Channel Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Figure 11 Moving Average . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 12 Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 13 Probe Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 14 Edit Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 15 Copy Prob e . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 4

Figure 16 Test Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 17 Print Probe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 18 Default Probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 19 Clear Stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 20 Fields Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Figure 21 Select Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 22 Edit Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 23 Default Fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Figure 24 Display Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 25 Logging Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Figure 26 Demand Log Submen u . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5

Figure 27 Store Readings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Figure 28 Log History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Figure 29 Demand Log View Data . . . . . . . . . . . . . . . . . . . . . . . . . 58

Figure 30 Print Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Figure 31 Delete Dat a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 0

Figure 32 Logging Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 33 Auto Log Submenu . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Figure 34 Log Statistics (Auto Log Started) . . . . . . . . . . . . . . . . . . . . 63

Figure 35 Start Sto p . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3

Figure 36 Auto Log View Data . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Figure 37 Print Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Figure 38 Delete Dat a . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 6

Figure 39 Log Stats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Figure 40 Data Labels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

vii

Download from Www.Somanuals.com. All Manuals Search And Download.

Figure 41 Default Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Figure 42 System Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Figure 43 Comm Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Figure 44 Date Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

Figure 45 Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Figure 46 Password for Calibration Acces s . . . . . . . . . . . . . . . . . . . . . 7 5

Figure 47 Select Calibration Channe l . . . . . . . . . . . . . . . . . . . . . . . . 7 6

Figure 48 Pass Cal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Figure 49 Serial Cable Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Figure 50 Using a Shorting Wire . . . . . . . . . . . . . . . . . . . . . . . . . 132

viii

Download from Www.Somanuals.com. All Manuals Search And Download.

Tables

International Electrical Symbols . . . . . . . . . . . . . . . . . . . . . 1

Conversion Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Alphabetical List of Commands . . . . . . . . . . . . . . . . . . . . . 81

Statistical Calculation T y pes . . . . . . . . . . . . . . . . . . . . . . 126

Field Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126

Reference (REF) Keywords. . . . . . . . . . . . . . . . . . . . . . . 127

Conversion Types, Mnemonics, and Serial Port Responses . . . . . . 128

Conversion Types and Parameters . . . . . . . . . . . . . . . . . . . 128

RJC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Table 10 Port Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129

Table 11 Date Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Table 12 Time Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

Table 13 PRT and Thermistor Calibration Parameter Description . . . . . . . . 131

Table 14 Calibration Parameters . . . . . . . . . . . . . . . . . . . . . . . . . 135

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Before You Start

Symbols Used

Before You Start

1.1

Symbols Used

Table 1 lists the symbols that may be used on the instrument or in this manual

Table1 International Electrical Symbols

and the meaning of each symbol.

Symbol

Description

AC (Alternating Current)

AC-DC

Battery

Complies with European Union Directives

DC (Direct Current)

Double Insulated

Electric Shock

Fuse

PE Ground

Hot Surface (Burn Hazard)

Read the User’s Manual (Important Information)

Off

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Symbol

Description

Canadian Standards Association

OVERVOLTAGE (Installation) CATEGORY II, Pollution Degree 2 per IEC1010-1 re-

fers to the level of Impulse Withstand Voltage protection provided. Equipment of

OVERVOLTAGE CATEGORY II is energy-consuming equipment to be supplied from

the fixed installation. Examples include household, office, and laboratory appliances.

C-TIC Australian EMC mark

The European Waste Electrical and Electronic Equipment (WEEE) Directive

(2002/96/EC) mark.

1.2

Safety Information

Use this instrument only as specified in this manual. Otherwise, the protection

provided by the instrument may be impaired. Refer to the safety information in

Sections 1.2.1 and 1.2.2.

The following definitions apply to the terms “Warning” and “Caution”.

• “Warning” identifies conditions and actions that may pose hazards to the

user.

• “Caution” identifies conditions and actions that may damage the instru-

ment being used.

1.2.1

Warnings

• DO NOT use this unit in environments other than those listed in the

User’s Guide.

• Follow all safety guidelines listed in the User’s Guide.

• Calibration equipment should only be used by trained personnel.

• This instrument can measure extreme temperatures. Precautions must be

taken to prevent personal injury or damage to objects. Probes may be ex-

tremely hot or cold. Cautiously handle probes to prevent personal injury.

Carefully place probes on a heat/cold resistant surface or rack until they

reach room temperature.

• The AC adapter can present safety concerns if misused or damaged. To

avoid the risk of electric shock or fire, do not use the AC adapter outdoors

or in a dusty, dirty, or wet environment. If the cord, case, or plug of the

adapter is damaged in any way, discontinue its use immediately and have

it replaced. Never disassemble the AC adapter. Use only the AC adapter

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Before You Start

Safety Information

provided with the instrument or equivalent adapter recommended by the

manufacturer of this instrument.

• The AC adapter has circuits with high voltage inside that could present

danger of electrical shock or fire if exposed. If the AC adapter is damaged

in any way or becomes hot, discontinue its use immediately, disconnect it

from any AC supply, and have it replaced. Do not attempt to open, repair,

or continue using a damaged or defective AC adapter.

• The instrument batteries can present danger if not handled properly. To

avoid the risk of exposure to dangerous substances or explosion, immedi-

ately remove the batteries and discontinue use if they leak or become

damaged. Never allow the batteries to be shorted, heated, punctured, or

dropped. If the instrument is physically damaged, immediately remove

the batteries to insure that they do not become shorted. While removed

from the instrument, store the batteries in a location so that they do not

come into contact with metal or fluids that might short circuit the batteries

and where they are safe from excessive temperatures. Used batteries must

be disposed of properly. Check your local regulations for additional infor-

mation. Never dispose of batteries in fire which may result in explosion

with the possibility of personal injury or property damage.

• DO NOT use this instrument in combination with any probe ( PRT,

thermistor, or thermocouple) to measure the temperature or resistance of

any device where the probe might come in contact with a conductor that

is electrically energized. Severe electric shock, personal injury, or death

may occur.

1.2.2

Cautions

• If the instrument is dropped, struck, or handled in a way that causes inter-

nal or external physical damage, immediately unplug the AC adapter, re-

move the batteries, discontinue use, and contact the factory for repair. Do

not attempt to disassemble or repair the instrument, batteries, or AC

adapter. Refer repairs or replacement components to the manufacturer.

• The instrument and thermometer probes are sensitive and can be easily

damaged. Always handle these devices with care. DO NOT allow them to

be dropped, struck, stressed, or overheated.

• Probes are fragile devices which can be damaged by mechanical shock,

overheating, and absorption of moisture or fluids in the wires or hub.

Damage may not be visibly apparent but nevertheless can cause drift, in-

stability, and loss of accuracy. Observe the following precautions:

• DO NOT allow probes to be dropped, struck, bent, or stressed.

• DO NOT overheat probes beyond their recommended temperature range.

• DO NOT allow any part of the probe other than the sheath to be im-

mersed in fluid.

• DO NOT allow the probe hub or wires to be exposed to excessive temper-

atures.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

• Keep the probe wires clean and away from fluids.

1.3

Authorized Service Centers

Please contact one of the following authorized Service Centers to coordinate

service on your Hart product:

Fluke Corporation, Hart Scientific Division

799 E. Utah Valley Drive

American Fork, UT 84003-9775

USA

Phone: +1.801.763.1600

Telefax: +1.801.763.1010

E-mail: [email protected]

Fluke Nederland B.V.

Customer Support Services

Science Park Eindhoven 5108

5692 EC Son

NETHERLANDS

Phone: +31-402-675300

Telefax: +31-402-675321

E-mail: [email protected]

Fluke Int'l Corporation

Service Center - Instrimpex

Room 2301 Sciteck Tower

22 Jianguomenwai Dajie

Chao Yang District

Beijing 100004, PRC

CHINA

Phone: +86-10-6-512-3436

Telefax: +86-10-6-512-3437

E-mail: [email protected]

Download from Www.Somanuals.com. All Manuals Search And Download.

1 Before You Start

Authorized Service Centers

Fluke South East Asia Pte Ltd.

Fluke ASEAN Regional Office

Service Center

60 Alexandra Terrace #03-16

The Comtech (Lobby D)

118502

SINGAPORE

Phone: +65 6799-5588

Telefax: +65 6799-5588

E-mail: [email protected]

When contacting these Service Centers for support, please have the following

information available:

• Model Number

• Serial Number

• Voltage

• Complete description of the problem

Download from Www.Somanuals.com. All Manuals Search And Download.

2 Introduction

Introduction

The Hart 1529 is a low-cost, high-accuracy, digital thermometer readout de-

signed to be used with 25 and 100Ω PRTs, thermistors, and thermocouples. Its

unique combination of features makes it suitable for a wide variety of applica-

tions from laboratory measurement to industrial processes. Features of the 1529

include:

• Measures 25Ω and 100Ω PRTs, thermistors, and thermocouples

• Four inputs: two PRT/thermistor and two thermocouple (standard config-

uration)

• Four-wire connection eliminates lead resistance effects in PRTs

• Three-wire measurement mode for three-wire RTDs

• Exclusive patented mini-DWF connectors (U.S. Patent No. 5,964,625)

• Automatic current reversal eliminates thermoelectric EMF errors

• Accuracy: PRTs to 0.006°C, thermistors to 0.002°C, and thermocouples

to 0.3°C

• Typical resolution: PRTs 0.001°C, thermistors 0.0001°C, thermocouples

0.01°C

• Measures four sensors simultaneously with a fast one-second measure-

ment cycle

• Measures one sensor at 10 readings per second (limited accuracy)

• Adjustable moving average for extra precision

• Stores over 8,000 measurements internally

• Accepts ITS-90, PT-100 (ASTM E1137, DIN 43760, or IEC-751), and

Callendar-Van Dusen PRT characterizations

• Accepts Steinhart-Hart R(T) or T(R) and YSI-400 type thermistor charac-

terizations

• Accepts thermocouple types B, E, J, K, N, R, S, T, Au-Pt, and polynomial

specified

• Temperature offsets for improved thermocouple accuracy

• Stores 10 additional sets of probe parameters

• Eight programmable display sets for display probe information, measure-

ment statistical data, or difference between measurements

• Password protection of settings

• Large, LCD, user-configurable, display viewable in bright or dim lighting

• Serial RS-232 and IR interface standard; IEEE-488 GPIB interface op-

tional

• Powered by external AC supply, 12-15V DC source, or internal recharge-

able battery

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Specifications and Environmental Conditions

Specifications

Specifications and Environmental

Conditions

3.1

Specifications

PRT

Thermistor

Thermocouple

Inputs

2 channels PRT/thermistor and 2 channels thermocouple

or 4 channels PRT/thermistor

or 4 channels thermocouple

PRT/thermistor channels accept 2,3, or 4 wires

Thermocouple channels accept B, E, J, K, N, R, S, T, and Au-Pt thermocouple types

Temperature Range¹

Measurement Range

–189 to 960°C

–50 to 150°C

0 to 500k

0 to 5k

–270 to 1800°C

–10 to 100 mV

0 to 400

0 to 20

Resistance / Voltage

Accuracy²

–10 to 50 mV: 0.005 mV

50 to 100 mV: 100 ppm of

reading

0.0005

0.0005k

20 to 400

25 ppm of reading

5 to 200k

reading

Ω: 100 ppm of

(Internal RJC: 0.25°C)

200 to 500 K

reading

300 ppm of

Characterizations

ITS-90,

Steinhart-Hart, YSI-400

NIST Monograph 175, 3-point

deviation function applied to

NIST 175, 6th-order polynomial

PT-100 (ASTM E1137, DIN 43760,

IEC-751),

Callendar-Van Dusen

Temperature Accuracy (meter

only)¹

0.004°C at –100°C

0.006°C at 0°C

0.009°C at 100°C

0.012°C at 200°C

0.018°C at 400°C

0.024°C at 600°C

0.0025°C at 0°C

0.0025°C at 25°C

0.004°C at 50°C

0.010°C at 75°C

0.025°C at 100°C

Type Ext./Int.RJC

0.6°C/ 0.6°C

0.07°C/ 0.25°C

0.1°C/ 0.35°C

0.15°C/ 0.4°C

0.15°C/ 0.3°C

0.4°C/ 0.5°C

0.5°C/ 0.6°C

0.1°C/ 0.3°C

Temperature Resolution,

typical³

0.001°

0.0001°

0.01 to 0.001°

Operating Range¹

Measurement Interval

Excitation Current

16 to 30°C

0.1 second to 1 hour; inputs may be read sequentially or simultaneously at 1 second or greater interval

1mA

(reversing)

N/A

2 and 10

selected

μA, automatically

Display

1.3” x 5" backlit LCD graphical display

Display Units

Data Logging

Logging Intervals

Averaging

°C, °F, K,

Ω, KΩ, mV

Up to 8,000 time- and date-stamped measurements can be logged

0.1, 0.2, 0.5, 1, 2, 5, 10, 30, or 60 seconds; 2, 5, 10, 30, or 60 minutes

Moving average of most recent 2 to 10 readings, user selectable

Statistical Data

Average, standard deviation, minimum, maximum, spread, N, difference (delta)

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

PRT

Thermistor

Thermocouple

Probe Connection

Patented DWF connectors accepts spade lug, bare-wire, or banana

plug terminations

Universal receptacle accepts

miniature and standard

connectors

Communications

AC Power

DC Power

Battery

RS-232 and IR ports included, IEEE-488 (GPIB) optional

100 to 240 VAC, 50-60 Hz, 0.4A

12 to 16 VDC, 0.5 A (battery charges during operation from 14.5 to 16 VDC, 1.0A)

NiMH, 8 hours operation typical without backlight, 3 hours to charge, 500 cycles

4.0” H x 7.5” W x 8.2” D (102 x 191 x 208 mm)

Size

Weight

4.5 lbs. (2 kg)

¹The sensor generally limits the actual temperature range. Temperature accuracy specifications do not include sensor accuracy. Thermis-

tor temperature accuracy assumes a 10k sensor. Thermocouple accuracy is with internal reference junction compensation; accuracy is

improved with external reference junction compensation. Thermocouple temperature accuracies are given for external reference junction

compensation and internal reference junction compensation, respectively.

²Measurement accuracy specifications apply within the operating temperature range and assume 4-sample averaging and 4 lead wires for

PRTs. With 3-wire RTDs add 0.05

lead wires.

to the measurement accuracy plus the maximum possible difference between the resistances of the

³Actual resolution can be set greater than typical resolution, but the added digits (0.0001 max.) may not be meaningful to the measurement.

3.2

Environmental Conditions

Although the instrument has been designed for optimum durability and trou-

ble-free operation, it must be handled with care. The instrument should not be

operated in an excessively dusty, dirty, or wet environment. Maintenance and

cleaning recommendations can be found in the Maintenance section of this

manual.

For full accuracy, operate the instrument in ambient temperatures between

16–30°C (61–86°F). The battery may not charge properly at temperatures

above 30°C. Do not operate the instrument in an environment colder than 5°C

(41°F) or warmer than 40°C (104°F).

The instrument operates safely under the following conditions:

• Operating temperature range: absolute 5–40°C (41–104°F) [full accuracy

16–30°C (61–86°F)]

• Ambient relative humidity: maximum 80% for temperature <31°C, de-

creasing linearly to 50% at 40°C

• Pressure: 75 kPa–106 kPa

• Vibration should be minimized

• Altitude less than 2,000 meters

• Indoor use only

Download from Www.Somanuals.com. All Manuals Search And Download.

3 Specifications and Environmental Conditions

Warranty

3.3

Warranty

Fluke Corporation, Hart Scientific Division (Hart) warrants this product to be

free from defects in material and workmanship under normal use and service

for a period as stated in our current product catalog from the date of shipment.

This warranty extends only to the original purchaser and shall not apply to any

product, which, in Hart’s sole opinion, has been subject to misuse, alteration,

abuse or abnormal conditions of operation or handling.

Software is warranted to operate in accordance with its programmed instruc-

tions on appropriate Hart products. It is not warranted to be error free.

Hart’s obligation under this warranty is limited to repair or replacement of a

product, which is returned to Hart within the warranty period and is deter-

mined, upon examination by Hart, to be defective. If Hart determines that the

defect or malfunction has been caused by misuse, alteration, abuse or abnormal

conditions or operation or handling, Hart will repair the product and bill the

purchaser for the reasonable cost of repair.

To exercise this warranty, the purchaser must forward the product after calling

or writing a Hart Authorized Service Center (see Section 1.3). The Service

Center assumes NO risk for in-transit damage.

THE FOREGOING WARRANTY IS PURCHASER’S SOLE AND EXCLU-

SIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES, EX-

PRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY

IMPLIED WARRANTY OR MERCHANTABILITY, OR FITNESS FOR ANY

PARTICULAR PURPOSE OR USE. HART SHALL NOT BE LIABLE FOR

ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAM-

AGES OR LOSS WHETHER IN CONTRACT, TORT, OR OTHERWISE.

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Quick Start

Unpacking

Quick Start

This section briefly explains the basics of setting up and operating your 1529

Thermometer Readout.

4.1

Unpacking

Carefully unpack the 1529 thermometer readout. Verify that the following

items are present:

• 1529 Thermometer Readout (The battery inside the 1529 is completely

charged when shipped. Initial charging is not required.)

• AC Adapter/Charger and power cord

• Serial Cable

• Manual

• Report of Calibration

• Probe (optional-must be purchased separately)

• Two ferrites (for use with probes as described in Section 4.4.1, Using the

Clamp-on Ferites)

If all items are not present, call a Hart Authorized Service Center (see Section

1.3)

4.2

Use Proper Care

You must understand the safety issues related to the 1529. Be aware that poten-

tial hazards exist due to high temperatures and battery chemicals. Carefully

read the Warnings in Section 1.2.1 and Cautions in Section 1.2.2.

The 1529 and any thermometer probes used with it are sensitive instruments

that can be easily damaged. Always handle these devices with care. DO NOT

allow them to be dropped, struck, stressed, or over-heated.

4.3

4.4

Learn About the Features and Components

Familiarize yourself with the features and accessories of the 1529 by reading

Section 5, Parts and Controls.

Connect the Probe

The PRT/thermistor or thermocouple probe connects on the back panel of the

1529 using patented mini-DWF connectors (PRT/thermistor) or the universal

receptacles (thermocouples).

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

4.4.1

Using the Clamp-on Ferrites

Clamp-on ferrites are provided with this product for the use of improving its

electromagnetic (EM) immunity in environments of excessive EM interference.

During EMC testing we found that ferrites clamped around the probe cables

and power cord reduced the risk that EM interference affects measurements.

Therefore, we recommend that the clamp-on ferrites provided (Steward P/N

28A2025-0A2) be used on the cables of probes attached to this product, espe-

cially if it the product is used near sources of EM interference such as heavy in-

dustrial equipment.

To attach a ferrite to a probe cable, make a loop in the cable near the connector

and clamp the ferrite around half of the loop as shown in Figure 1. The ferrite

can be easily snapped open and moved to a new probe when needed.

probe cable

clamp-on ferrite

Figure 1 Using the Clamp-on Ferrites

4.5

4.6

Connect the Power Source

The 1529 draws power from either a 15-volt DC power supply (the included

AC adapter) connected to the DC input or the internal re-chargeable battery

pack. To use the AC adapter, plug it into a wall outlet of the appropriate voltage

and insert the DC plug into the DC power input of the 1529 (see Figure 3 on

page 18.)

Switch the Power On

Power is turned on and off with the power switch located on the top right cor-

ner of the back panel. To switch the power on, toggle the power switch to the

‘ON’ position. To switch power off, toggle the power switch to the ‘OFF’ posi-

tion. The instrument takes a few seconds to power up, initialize, and begin nor-

mal operation. A self-test is performed displaying the channel configuration

and status of the system, calibration, GPIB, memory, and buttons. If the ther-

mometer readout calibration has expired, the user is notified and must press the

Download from Www.Somanuals.com. All Manuals Search And Download.

4 Quick Start

Measure Temperature

Enter button to continue initialization. If an error message is displayed on

power up see Section 11.1, Troubleshooting.

4.7

Measure Temperature

After initialization, the temperature measurements for the configured channels

are displayed. The appropriate sensor type must be selected and coefficients en-

tered for the measurements to be accurate (see Section 7.2.1, Edit Probe). Place

the sensors of the probe into the object(s) you want to measure. DO NOT force

the probe(s) or otherwise allow them to be bent, stressed, or overheated. Probes

can be easily damaged if misused. For further suggestions on handling the

probe and using the 1529 and probe to measure temperature accurately, see

Section 6, General Operation. For information on the various modes of opera-

tion of the 1529 see Section 7, Display Functions.

Download from Www.Somanuals.com. All Manuals Search And Download.

5 Parts and Controls

Front Panel Buttons

Parts and Controls

The functions of the various features of the 1529 are described below.

5.1

Front Panel Buttons

The front panel buttons Enter/Menu, Unit, Contrast, and Exit are used to se-

lect and alter the functions of the thermometer readout (see Figure 2).

24.159C 24.634C

24.142C 24.015C

1 TYP: CVD

1 AVE: 24.1530 C

1 SER: 145-560

1 STD:

1 SPR:

0.0038 C

0.0219 C

1 –T1:

0.0000 C

ALOG: OFF 0%

TIME: 14:58:43

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 2 Front Panel

The function of each button is as follows:

Enter/Menu - This button displays and scrolls through the menu options. Use

this button to select the menu to enter and to save changes made to menu

choices.

Unit - LR Use these buttons to select the units C, F, or K when not in the

menu structure. In conjunction with the Menu button, use these buttons to

scroll left and right through menu options and choices.

Contrast -UD Use these buttons to lighten or darken the display when not in

the menu structure. In conjunction with the Menu button, use these buttons to

scroll up and down through menu options and choices.

Exit - Use this button to exit any menu. When editing a parameter, if the Exit

button is pressed, the immediate operation is canceled and control skips to the

next parameter. Holding the button down for several seconds, exits to the main

display.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

FLUKE CORPORATION

HART SCIENTIFIC DIVISION

www.hartscientifc.com

CHANNEL CONFIGURATION

CH1

CH2

CH3

CH4

1 AMP

14.5–16 V

–

IR PORT

CHARGING

POWER

RS-232

IEEE-488 (option)

FUSES INTERNAL - 1 A T 125 V

1529

1529-R

1529-T

Figure 3 Back Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

5 Parts and Controls

Back Panel

5.2

Back Panel

The back panel consists of the power switch, AC adapter connector, charging

indicator, IR port, RS-232 port connector, IEEE-488 port connector (optional),

serial label, and probe connectors. The 1529 thermometer readout can be con-

figured in three different ways. The configuration affects the probe connectors

on the back panel. The Model 1529 is configured with one PRT/thermistor in-

put module of two channels and one thermocouple input module of two chan-

nels. The Model 1529-R is configured with two PRT/thermistor input modules

of four channels. The Model 1529-T is configured with two thermocouple input

modules of four channels. Figure 3 shows the back panel and the three different

configurations.

Power Switch - The power switch turns the thermometer readout on and off.

AC Adapter Connecor - The AC adapter plugs into the DC power input to re-

charge the battery and to power the instrument while the battery is being

charged (see Section 6.3, Battery).

Charging Indicator - The charging indicator lights when the AC adapter is

connected. It glows green when the battery is at full charge and amber when the

battery is being charged.

IR Port-The infrared window provides a means for downloading the 1529

logged data. The infrared window can be used in any of the following ways.

• with an I/R dongle and the 9935 LogWare Software

• with a Hart Scientific 2385 printer

• with an IrDA compatible printer

RS-232 Port Connector - The DB-9 connector is for interfacing the thermom-

eter readout to a computer or terminal with serial RS-232 communications.

IEEE-488 Port (optional) - The GPIB connector is for interfacing the ther-

mometer readout to a computer or terminal with IEEE-488 communications.

Serial Label - The serial label shows the instrument model and serial number.

Probe Connectors - Probe(s) must be connected either to the patented

mini-DWF connectors (PRT/thermistor probes) or to the universal receptacle

(thermocouples) for operation.

5.3

Accessories

The 1529 thermometer readout comes standard with a hand strap on the side

for easy carrying of the instrument. The following accessories are also

available:

• 2513-1529 Rack Mount Kit

• 9323 Soft Carrying Case

• 9322 Hard Carrying Case

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

• 2380 Small Thermocouple Connector Kit

• 2381 Large Thermocouple Connector Kit

• 2374 I/R Dongle

• 2385 HP-IR Printer

• 2386 HP-IR Printer Adapter

• 2387 HP-IR Printer Paper

Download from Www.Somanuals.com. All Manuals Search And Download.

6 General Operation

Display

General Operation

This section explains basic operation of the 1529 thermometer readout. De-

tailed operation of the 1529 is explained in Sections 7 and 8. Section 7 explains

the menu structure and the functions available in the menu structure and Sec-

tion 8 explains the communications interface for operating the 1529 remotely.

6.1

Display

The 1529 display consists of two parts. The top portion of the display is used

for displaying the measurements from one to four inputs. The bottom portion of

the display is reserved for the programmable fields and field display sets. Infor-

mation about the channels and measurements can be displayed in greater detail

such as min, max, spread, standard deviation, and many other functions. When

the measure period is 0.1 or 0.2 seconds (fast measurement mode), the pro-

grammable fields and field display set information are not displayed.

6.2

Changing Units

The 1529 thermometer readout is capable of displaying temperature in Celsius

(C), Fahrenheit (F), or Kelvin (K). (Displaying in units of Ω, KΩ, or mV is also

available through the PROBE menu and is channel specific.) Temperature units

are changed on all channels (not individually) by pressing the buttons on the

front panel when not in the menu structure. Press the Unit, LR, buttons to

scroll forward and backward through C, F, or K. All channels or fields that are

displaying temperature on the upper or lower display are updated to the new

units.

Channels that are set to Ω, KΩ, or mV in the PROBE menu are left unchanged

when temperature units are modified. Changing the units resets the statistical

calculations (displayed in the bottom portion of the display).

6.3

Battery

The 1529 thermometer readout has a built-in nickel-metal-hydride battery pack

that can power the instrument for about eight hours before needing to be re-

charged. The battery discharges more quickly when the display backlight is

used. The percent of battery charge remaining is displayed on the bottom por-

tion of the display when the battery power is being used. The battery percent-

age is approximate and should only be used as a general guideline when

determining the length of charge remaining. The battery is recharged in situ

(while in place) using the AC adapter that is provided.

Plug the AC adapter into the wall outlet and connect the DC plug of the adapter

into the 1529. The battery is charged as necessary whether or not the instru-

ment is switched on. The power control circuit inside the instrument manages

battery charging and stops charging the battery automatically when the battery

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

is fully charged. Only charge the battery when ambient temperature is between

16°C and 30°C (61°F and 86°F) It normally takes about three hours to fully

charge the battery. The instrument can be operated while the battery is being

charged. The charging indicator on the back panel is green when the battery is

fully charged and amber when being charged using the AC adapter.

The battery may self-discharge over several months, especially if the tempera-

ture is warm. The battery pack can be used for a minimum of 500 charge-dis-

charge cycles before needing to be replaced. Replacement battery packs are

available from the manufacturer. The battery pack can be easily removed and

replaced in the field by following this procedure:

1. Power the 1529 off and unplug the AC adapter from the unit.

2. Turn the 1529 over to expose the battery compartment. Remove the bat-

tery cover hex screw. Place the screw in a safe place so it won’t get lost.

Flip open the battery cover to reach the battery pack.

3. Remove the battery pack. Gently disconnect the battery plug connector.

4. Attach the polarized plug of the new battery pack onto the connector.

Note: The battery plug is polarized and can only be plugged in one di-

rection. DO NOT force it. Place the battery pack in the battery

compartment.

5. Close the battery cover and replace the screw. Avoid pinching the battery

wires.

6. Plug in the AC adapter and charge for a minimum of four hours for the

initial charge. Used batteries must be disposed of properly. Check your

local regulations for additional information. You may return used batter-

ies to the manufacturer. Never dispose of batteries in fire as this may re-

sult in an explosion with the possibility of personal injury or property

damage.

When the battery charge is not at 100%, the measurement accuracy is not af-

fected. If the power is interrupted while the instrument is logging measure-

ments (on demand or automatically), the logged data is preserved and logging

resumes when the power is restored.

6.4

Probe Input Modules

The 1529 can be configured in three ways:

• Two RTD/thermistor input modules.

• Two thermocouple input modules.

• One RTD/thermistor and one thermocouple input module.

Each input module supports two channels. Your 1529 thermometer readout is

configured at the factory and is not field changeable. Input modules should

never be removed for any reason.

Download from Www.Somanuals.com. All Manuals Search And Download.

6 General Operation

Probe Input Modules

All possible configurations are shown in Figure 3 on page 18.

6.4.1

Connecting a PRT or Thermistor Probe

PRT and thermistor probes are attached to the resistance input module via Hart

Scientific mini-DWF connectors. These patented connectors accept bare wire,

spade, or mini banana plug terminations. The connectors are color coded for

ease in connecting lead-wires.

When using 2- and 3-wire sensors, the accuracy of the 1529 is reduced as

stated in the specifications. Compensation is made for 3-wire PRTs, but the dif-

ference in lead resistance affects the measurement accuracy. The 1529 ther-

mometer readout is unable to compensate for 2-wire lead resistance.

Attach the lead-wires of the probes as shown in Figure 5 on page 24. The top

termainals sense current and the bottom terminals sense potential.

6.4.2

Connecting a Thermocouple

The 1529 thermocouple input module accepts both standard and sub-miniature

size thermocouple connectors. The connection is made with the positive termi-

nal on the right and the negative terminal on the left. You must use a connector

that matches the thermocouple type for the internal RJC to be accurate. For ex-

ample, if you are using a type K thermocouple you must also use a type K con-

nector, which is made from the same type of metal. For best results, wait two

minutes before measuring after inserting the thermocouple connector into the

input module.

FLUKE CORPORATION

HART SCIENTIFIC DIVISION

www.hartscientifc.com

CHANNEL CONFIGURATION

CH1

CH2

CH3

CH4

1 AMP

14.5–16 V

–

IR PORT

CHARGING

POWER

RS-232

IEEE-488 (option)

FUSES INTERNAL - 1 A T 125 V

Figure 4 Thermocouple Connections

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Channel 1

Channel 2

Shield

Connecting 4-wire probes

Channel 1

Channel 2

Connecting 3-wire probes

Channel 1

Channel 2

Connecting 2-wire probes

Figure 5 Probe Connection Wiring Diagram

Download from Www.Somanuals.com. All Manuals Search And Download.

6 General Operation

DC Power Source

6.5

DC Power Source

Caution: For CE compliance and for performance, use only the AC

adapter shipped with the instrument by Hart Scientific. If the AC adapter

needs to be replaced, contact a Hart Authorized Service Center (see Sec-

tion 1.3).

The DC power source provides power to charge the battery. It can also be used

to power the 1529 while the battery is being charged. The AC adapter provided

with the 1529 is intended for these purposes. The DC power source plugs into

the DC power input on the back panel of the instrument. The AC adapter has

circuits with high voltages inside that could present danger of electric shock or

fire if exposed. If the AC adapter is damaged in any way or becomes hot, dis-

continue use immediately, disconnect the adapter from any AC supply, and re-

place the adapter. Do not attempt to open, repair, or continue using a damaged

or defective AC adapter.

6.6

6.7

Power On Self-Test

When power is turned on, the 1529 performs a self-test checking the system, all

channels, calibration, GPIB, memory, and buttons. If an error occurs, an error

message is displayed. See Section 11.1, Troubleshooting for additional infor-

mation on error messages.

Display Backlight and Contrast

The display backlight is adjustable for use in varying lighting conditions. The

four backlight modes are accessible in the CHANNEL menu DISPLAY OP-

TIONS function. If the display appears faded, dark, or blank, adjust the con-

trast (off, low, medium, high) using the front panel contrast buttons.

6.8

Taking Measurements

The procedure for configuring the 1529 thermometer readout to take measure-

ments on a particular input channel requires the following: (1) connecting the

sensor to the appropriate input channel , (2) enabling the channel, and (3) se-

lecting the conversion type and probe characterization values.

6.8.1

Connecting the Sensor

Connect the sensor to the RTD/Thermistor channel(s) or thermocouple chan-

nel(s) that you want to measure. Refer to Section 7.4, Probe Input Modules, for

additional information.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

6.8.2

Enabling the Channel

Channels are set first by selecting either simultaneous or scan mode in the

CHANNEL menu CHANNEL MODE function. Simultaneous mode shows one

to four channels in the upper display simultaneously. Scan mode shows one

channel at a time (in large digit format) scanning through one to four channels

depending on the channels that are enabled. After the mode has been selected,

use the CHANNEL menu ENABLE CHANNEL function, to select the channel

to be displayed. Any channel set to ‘Off’ is not displayed. See Sections 7.1.3,

Channel Mode, and 7.1.2, Enable Channel, for more information.

6.8.3

Selecting Conversion Type and Probe Characterization

Before the 1529 can accurately measure temperature, it must be configured to

calculate temperature from the resistance or voltage of the sensor. There are

many temperature conversion algorithms available and the one to use depends

on the type of sensor and its calibration. Many conversion algorithms use coef-

ficients that characterize the sensor. Coefficients are determined when the sen-

sor is calibrated. SPRTs and RTDs often use the ITS-90 algorithms and are

provided with ITS-90 characterization coefficients. Thermistors often use the

Steinhart-Hart algorithms and coefficients. Thermocouples use standard tables

or equations depending on its type. For additional information on conversion

types, see Section 7.2, Probe Menu.

The conversion type and characterization coefficients for a sensor are specified

using the PROBE menu EDIT PROBE function (see Section 7.2.1).

6.9

Fast Measurement Mode

Fast Measurement Mode applies to measure periods of 0.1, 0.2, or 0.5 seconds.

This mode allows measurements to be displayed or logged quickly.

Normally, when each measurement is made a self-calibration of the measure-

ment circuit is performed simultaneously during the measurement process to

offset errors from component drift and spurious EMFs. For measure periods of

0.1, 0.2, and 0.5 seconds, the fast measurement rate is achieved by foregoing

the self-calibration. The drawback to this Fast Measurement Mode is the accu-

racy of the measurement may be poor and subject to drift. Accuracy can be

temporarily improved using the AUTO-CAL function that appears in the

CHANNEL menu when in this Fast Measurement Mode. The AUTO-CAL

function causes the instrument to perform a single self-calibration of the mea-

surement circuit then resume fast measuring (without automatic

self-calibration).

See Section 8.1.1 for detailed information on using the Fast Measurement

Mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

6 General Operation

Data Logging

6.10

Data Logging

Data can be logged either on demand or automatically at a user-selected inter-

val. When data is logged, readings are stored to the instrument's memory and

assigned a label for easy recall and organization of data. Up to 100-demand log

and 8,160 auto log readings can be stored. When data is being logged, the left

bottom corner of the main display shows a strip-recorder indicator.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Channel Menu

Menu Functions

Selecting the Enter/Menu button from the front panel accesses the main menu

of the 1529 thermometer readout. The main menu consists of the submenus:

CHANNEL, PROBE, FIELDS, LOGGING, and SYSTEM. Each submenu

has its own set of functions. The Enter/Menu button is used to select and save

menu choices. The Unit LR buttons are used to scroll forward or backward

through the functions. The Exit button is used to return from a function to the

previous menu or step through parameters.

24.159C 24.634C

24.142C 24.015C

LR to select menu item. Press ENTER.

CHANNEL

PROBE

FIELDS

LOGGING

SYSTEM

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 6 Main Menu

7.1

Channel Menu

The CHANNEL menu provides functions for setting the measurement period,

selecting channels, setting the channel display mode, and setting measurement

averaging. The functions that appear in the CHANNEL menu are MEASURE

PERIOD, ENABLE CHANNEL, CHANNEL MODE, MOVING AVERAGE,

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

and DISPLAY OPTIONS/AUTO-CAL. (The DISPLAY OPTIONS changes to

AUTO-CAL when the measure period is less than 1 second.)

24.159C 24.634C

24.142C 24.015C

MEASUREMENT CONTROL FUNCTIONS

MEASURE

PERIOD

ENABLE

CHANNEL

MODE

MOVING

AVERAGE

DISPLAY

OPTIONS

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 8 Channel Menu

7.1.1

Measure Period and Fast Measurement Mode

The MEASURE PERIOD function allows you to control the period (time) be-

tween measurements. You may select between 0.1, 0.2, 0.5, 1, 2, 5, 10 and 30

seconds, 1, 2, 5, 10, and 30 minutes, or 1 hour. Note: Accuracy may be reduced

in measurement periods less than one second. When this function is selected,

the bottom portion of the display shows the current setting and allows the set-

ting to be changed.

24.159C 24.634C

24.142C 24.015C

MEA PER: 1 SEC

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 7 Measure Period

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Channel Menu

The LR buttons are used to select the period between measurements. Press

the Enter button to save the new setting. Press the Exit button to cancel and to

exit to the menu.

When the measure period is set to less than 1 second (i.e. 0.1, 0.2, 0.5 seconds)

the 1529 enters the Fast Measurement Mode. The menu buttons may seem to be

sluggish in this mode as the processor is making faster measurements. When in

the Fast Measurement Mode, the following changes occur at 0.1, 0.2, and 0.5

seconds.

• The channel display is updated quicker.

• The DISPLAY FUNCTIONS function changes to the AUTO-CAL func-

tion.

• The measurement accuracy is reduced and is subject to uncertainty factors

that are not typically introduced in a normal full measurement cycle.

• With serial port printing (see Section 7.5.1.1) measurements are printed

without the time and date and other associated information.

The following occur if the measure period is set to 0.1 or 0.2 seconds.

• The CHANNEL MODE function becomes unavailable.

• The 1529 measures one channel in scan mode.

• The field information normally displayed in the bottom portion of the dis-

play is not updated or displayed. The message, FIELD DATA NOT

AVAILABLE AT THIS RATE, is displayed.

The following occur if the measure period is set to 0.5 seconds.

• The 1529 can measure up to four channels in scan or simultaneous mode.

The Fast Measurement Mode is automatically implemented when the measure

period is set to less than 1 second. If the measure period is set to 0.1 or 0.2 sec-

onds and the Enter button is pressed, the following message is display.

ONE CHANNEL ONLY. SETTINGS CHANGED.

SELECT CHANNEL USING ENABLE CHANNEL.

ACCURACY NOT GUARANTEED AT THIS RATE.

Press ENTER to continue …

Press the Enter button to confirm and to continue. The display is automatically

changed to display one channel in large digit format. If more than one channel

is enabled, the first channel is left enabled and the other channels are automati-

cally disabled. To enable a different channel, use the ENABLE CHANNEL

function from the CHANNEL menu. See Section 8.1.2. Press the Exit button

to cancel.

If the measure period is set to 0.5 seconds and the Enter button is pressed, the

following message is display.

ACCURACY NOT GUARANTEED AT THIS RATE.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Press ENTER to continue …

Press the Enter button to confirm and to continue. The display is remains un-

changed and all enabled channels remain enabled channels. Press the Exit but-

ton to cancel.

When the measure period is reset to 1 second or greater, the following message

is displayed indicating that the 1529 is returning to normal operation.

FULL ACCURACY.

The DISPLAY FUNCTIONS function of the CHANNEL menu reappears and

the CHANNEL MODE function is available.

Note: Accuracy in the Fast Measurement Mode is affected by ambient condi-

tions, changes in measured temperature, higher measured temperature, and the

time duration from using the AUTO-CAL function. To reduce the uncertainty

in the Fast Measurement Mode, use the 1529 in a controlled ambient environ-

ment, in a very stable bath or dry block at lower temperatures, and use the

AUTO-CAL function often.

7.1.2

Enable Channel

The ENABLE CHANNEL function enables and disables measuring of each

channel. If a channel is off, its measurement is not displayed on the top portion

of the display in either scan or simultaneous display modes. When this function

is selected, the bottom portion of the display shows the on/off status of each

configured channel and allows the setting to be changed. Each configured chan-

nel is identified by its channel number.

24.159C 24.634C

24.142C 24.015C

CHAN 1:

CHAN 2:

CHAN 3:

CHAN 4:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 9 Enable Channel

Use the UD buttons to select the channel to change. The LR buttons are

used to change the setting. Press the Enter button to save the setting. Press and

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Channel Menu

hold the Exit button to cancel to the main display or press the EXIT button to

cancel and to move to the next parameter.

7.1.3

Channel Mode

The CHANNEL MODE function sets the channel display mode. When this

function is selected, the bottom portion of the display shows the current scan

mode and allows the setting to be changed.

24.159C 24.634C

24.142C 24.015C

SC MODE: SIMULT

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 10 Channel Mode

The following scan modes are available:

• SCAN - measures enabled channels scanning through and displaying the

channels one at a time, sequentially, in large digit format.

• SIMULT - measures and displays enabled channels simultaneously.

The LR buttons are used to select a setting. Press the Enter button to save

the setting and exit. Press the Exit button to cancel and to exit to the menu.

If the measure period is 0.1 or 0.2 seconds, the CHANNEL MODE function is

unavailable. The channel mode is automatically set to scan mode. The follow-

ing message is displayed when the CHANNEL MODE function is selected.

NOT AVAILABLE AT THIS RATE.

Press ENTER to continue…

If the measure period is 0.5 seconds or greater, the channel mode operates

normally.

7.1.4

Moving Average

The MOVING AVERAGE function sets the input averaging. The moving aver-

age filter is useful for smoothing variations in the measurements and for im-

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

proving resolution. When this function is selected, the bottom portion of the

display shows the averaging setting and allows the setting to be changed. Select

the number of raw measurements to be averaged to produce the displayed mea-

surement. The range is from 1 to 10. The factory default is 1.

The measurements are averaged together until the selected number of measure-

ments to average has been reached. Then the calculated average is based on the

selected number of measurements to average. For example, if the selected num-

ber of measurements to average is selected as 3, the 1st measurement is dis-

played, the 1st and 2nd measurements are averaged and displayed, and then the

1st, 2nd, and 3rd measurements are averaged and displayed. From this point

forward each displayed measurement consists of the last three measurements

averaged together.

24.159C 24.634C

24.142C 24.015C

AVERAGE:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 11 Moving Average

The LR buttons are used to select a setting. Press the Enter button to save

the setting and exit. Press the Exit button to cancel and to exit to the menu.

7.1.5

Display Options/Auto-Cal

The DISPLAY OPTIONS function is displayed when the measure period is one

second or greater and allows you to select the display resolution, decimal char-

acter, and lamp illumination. The AUTO-CAL function is displayed when the

measure period is 0.1, 0.2, or 0.5 seconds and allows a full measurement to be

taken. When the DISPLAY OPTIONS function is selected, the bottom portion

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

of the display shows the current display settings. This function is the same as

the FIELDS menu DISPLAY OPTIONS function.

24.159C 24.634C

24.142C 24.015C

RESOL:

DECIMAL:

LAMP:

OFF

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 12 Display Options

The RESOL parameter determines the number of decimal places (0 through 4

or AUTO) to be displayed for the temperature measurements. If AUTO is se-

lected, the instrument automatically determines the number of decimal places

to display depending on the probe conversion type.

The DECIMAL parameter is for selecting the character used as the decimal

separator. The choices are period (.) or comma (,).

The LAMP parameter specifies the brightness of the display (OFF, LOW,

MED, HIGH). Enabling this parameter causes the battery to discharge faster.

Use the LR buttons to change the parameter setting. Use the UD buttons

to scroll between the parameters. Press the Enter button to save the new set-

ting. Press and hold the Exit button to cancel to the main display or press the

EXIT button to cancel and to move to the next parameter.

When the AUTO-CAL function is selected, the following message is displayed.

FAST MODE AUTO CAL.

Press ENTER to continue...

Press the Enter button to perform the full measurement function. Press the

Exit button to cancel and to exit to the menu.

7.2

Probe Menu

The PROBE menu provides functions for specifying the channel, probe type,

the type of temperature conversion and coefficients, copying probe parameters,

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

testing conversion settings, viewing and printing probe parameters, and clearing

the default probe. The functions that appear in this menu are EDIT PROBE,

COPY PROBE, TEST PROBE, PRINT PROBE, and DEFAULT PROBE.

24.159C 24.634C

24.142C 24.015C

PROBE CHARACTERIZATION FUNCTIONS

EDIT

PROBE

COPY

PROBE

TEST

PROBE

DEFAULT

PROBE

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 13 Probe Menu

7.2.1

Edit Probe

The EDIT PROBE function allows you to select a probe channel, enter the

probe serial number, and select the conversion type and characterization coeffi-

cients and parameters. You select the probe channel from one of the four probe

channel setups or from one of the ten memory setups.

The EDIT PROBE function can be password protected to restrict access. See

Section 8.5.3, Password, for more information. If this function is password pro-

tected, the user is prompted to enter the password to gain access. If an incorrect

password is entered, the display shows the message PASSWORD INCOR-

RECT and access is denied. If the correct password is entered or if this function

is not password protected, the bottom portion of the display shows the probe

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

channel, the probe serial number and the conversion type. The characterization

coefficients and parameters are displayed after the conversion type is selected.

24.159C 24.634C

24.142C 24.015C

URANGE: 100Ω

PROBE:

SERIAL:

TYPE:

WIRES:

RO:

DAL:

CHAN-1

145-560

CVD

100.0000

0.003850000

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 14 Edit Probe

The PROBE parameter is for selecting any one of the four input channels:

CHAN1, CHAN2, CHAN3 and CHAN4 or one of the ten probe memory chan-

nels: PMEM0, PMEM1, PMEM2, PMEM3, PMEM4, PMEM5, PMEM6,

PMEM7, PMEM8, and PMEM9. The probe memory channels are for storing

probe settings that can later be used to copy to an input channel.

The SERIAL parameter is the serial number of the probe being edited. The se-

rial number consists of a string of up to eight characters using any numeric dig-

its, letters, and underscore.

The TYPE parameter is the conversion type for the corresponding input chan-

nel. The list of possible conversion types for each probe type is given in Table

2. The conversion types available are dependent on the probe or channel type as

indicated in the table. The characterization coefficients and parameters are dis-

played after the conversion type is selected. These coefficients may change de-

pending on the selected conversion type. The conversions and related

coefficients and parameters are explained in the following sections.

The LR buttons are used to select the parameter setting. The UD buttons

are used to scroll between and to change each digit of the parameter. Press the

Enter button to change and save the new setting. Press and hold the Exit button

to cancel to the main display or press the EXIT button to cancel and to move to

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

the next parameter. On the last parameter, press the Exit button to exit to the

menu.

Table 2 Conversion Types

Probe Type

Conversion Type

SPRT, PRT, RTD

ITS-90 (default)

ITS-SR5

PT-100

CVD

RES (

Ω)

Thermistor

THRM R(T)

THRM T(R)

YSI-400

RES (K

Ω)

Thermocouple

TC-K (default)

VIN [mV]

TC-B

TC-E

TC-J

TC-N

TC-R

TC-S

TC-T

TC-AU/PT

Polynomial

7.2.1.1

ITS-90 Conversion

The ITS-90 conversion is for PRTs calibrated and characterized using the Inter-

national Temperature Scale of 1990 equations. The parameters that appear

when ITS-90 is selected are RTPW, A4, B4, A, B, C, and D. These should be

set with the corresponding values that appear on the calibration certificate for

the PRT. The parameter RTPW takes the triple point of water resistance from

the certificate. The parameters A, B, C, and D take the an, bn, cn, and d coeffi-

cients from the certificate, where n is a number from 6 to 11. Parameters A4

and B4 take the a4 and b4 coefficients on the certificate. Any ITS-90 parameter

of the 1529 that does not have a corresponding coefficient on the PRT certifi-

cate must be set to 0.

When the ITS-90 conversion type is selected, the RANGE, WIRES, and coeffi-

cients are displayed on the right portion of the bottom of the display. The UD

buttons are used to scroll through the coefficients. Use the Enter button to edit

and to save the new settings. Use the LR buttons to change each digit of the

settings. Press and hold the Exit button to cancel to the main display or press

the EXIT button to cancel and to move to the next parameter. On the last pa-

rameter, press the Exit button to exit the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

The RANGE parameter is used to select the appropriate resistance range. For

25 ohm and 100 ohm PRTs select 100 ohms and for 1000 ohm PRTs select 10K

ohms.

The WIRES parameter sets the appropriate number of lead wires from the sen-

sor. This parameter can be set to 2-, 3-, or 4-wires. See Figure 5 on page 24 for

the wiring configuration.

The following table shows which parameter to set for each of the coefficients

that may appear on the certificate. Note: If the certificate has two sets of coeffi-

cients, one set for “zero-power” calibration and one set for 1 mA calibration,

use the coefficients for the 1 mA calibration.)

Matching Certificate Values to the 1529 ITS-90 Coefficients

1529 ITS-90 Coefficients

Certificate Value

a6, a7, a8, a9, a10, or a11

b6, b7, b8, or b9

c6, c7

The following example demonstrates how to set the ITS-90 parameters for the

case where a PRT was calibrated to ITS-90 and its calibration certificate states

values for coefficients Rtpw, a4, b4, a8, and b8. Set the 1529 parameters with

values from the certificate as follows.

Setting Coefficients Rtpw, a8, b8, a4, and b4

1529 ITS-90 Coefficients

Certificate Value

RTPW

Rtpw

7.2.1.2

ITS-SR5

The ITS-SR5 conversion is a special case of the ITS-90 conversion type. This

conversion is for the ITS-90 sub-range 5 only.

When the ITS-SR5 conversion type is selected, the RTPW, A5, and B5 coeffi-

cients are displayed on the right portion of the bottom of the display. The UD

buttons are used to scroll through the coefficients. Use the Enter button to edit

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

and to save the new settings. Use the LR buttons to change each digit of the

settings. Press and hold the Exit button to cancel to the main display or press

the EXIT button to cancel and to move to the next parameter. On the last pa-

rameter, press the Exit button to exit the menu.

7.2.1.3

PT-100 Conversion

The parameters for the PT-100 conversion are R0 (R0), ALPHA (α), DELTA

(δ), and BETA (β). These parameters cannot be changed by the user and are set

to; R0: 100.0, ALPHA: 0.00385055, DELTA: 1.4998, and BETA: 0.109, which

are applicable to the ASTM E1137 type PRTs, also known as DIN-43760 or

IEC-751.

When the PT-100 conversion type is selected, the RANGE and WIRES parame-

ters are displayed on the right portion of the bottom of the display. The UD

buttons are used to scroll through the parameters. Use the Enter button to

change and save the new settings. Press and hold the Exit button to cancel to

the main display or press the EXIT button to cancel and to move to the next pa-

rameter. On the last parameter, press the Exit button to exit the menu.

The RANGE parameter is used to select the appropriate resistance range. Gen-

erally, this should be set to 100 ohms.

The WIRES parameter sets the appropriate number of lead wires from the sen-

sor. This parameter can be set to 2-, 3-, or 4-wires. See Figure 4 on page 24 for

the wiring configuration.

7.2.1.4

Callendar-Van Dusen (CVD) conversion

The following equations are used for the Callendar-Van Dusen conversion:

⎧

⎫

⎬

⎭

⎡

⎤

⎛

⎞

R 1 + α t −δ

−1

t ≥ 0

t ≤ 0

⎜

⎟

⎨

⎪

⎨

⎢

⎥

⎦

⎝

⎠

100 100

⎣

⎩

r(t[°C ]) =

⎧

⎫

⎬

⎭

⎡

⎤

⎥

⎛

⎜

⎝

⎞

⎛

⎜

⎝

⎞ ⎛

⎞

⎟

⎠

⎪

R 1 + α t −δ

−1 −β

−1

⎟

⎟ ⎜

⎢

⎨

⎠

⎠ ⎝

⎪

⎩

100 100

100

⎢

⎣

⎥

⎦

⎪

⎩

The user-defined parameters for the Callendar-Van Dusen conversion are R0

(R0), ALPHA (α), DELTA (δ), and BETA (β). The defaults are R0: 100.0, AL-

PHA: 0.00385055, DELTA: 1.4998, and BETA: 0.109, which are applicable

with DIN-43760 or IEC-751 type PRTs.

Some probes may be provided with A, B, and C coefficients for the

Callendar-Van-Dusen equation in the following form:

⎧

⎨

R 1 + At + B

t ≥ 0

t ≤ 0

(

)

r(t[°C]) =

R 1 + At + Bt²+ C t −100 t³

(

)

[

]

⎪

⎩

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

The A, B, and C coefficients can be converted to α, δ, and β coefficients using

the following formulas:

100

10⁸C

α = A +100B

δ = −

β = −

A +100B

100B

When the CVD conversion type is selected, the R0, ALPHA, DELTA, and

BETA coefficients are displayed on the right portion of the bottom of the dis-

play. Use the UD buttons to scroll through the coefficients. Use the Enter

button to edit and save the new setting. Press and hold the Exit button to cancel

to the main display or press the EXIT button to cancel and to move to the next

parameter. On the last parameter, press the Exit button to exit to the menu.

7.2.1.5

RES Conversion

The RES conversion displays the measurement as resistance in ohms or K

ohms depending on the range.

When the RES conversion type is selected, the RANGE and WIRES parameters

are displayed on the right portion of the bottom of the display. The UD but-

tons are used to scroll through the parameters. Use the Enter button to change

and save the new settings. Press and hold the Exit button to cancel to the main

display or press the EXIT button to cancel and to move to the next parameter.

On the last parameter, press the Exit button to exit the menu.

The RANGE parameter is used to select the appropriate resistance range. For

25 ohm and 100 ohm PRTs, select 100 ohm and for 1000 ohm PRTs, select 10

K ohm.

The WIRES parameter sets the appropriate number of lead wires from the sen-

sor. This parameter can be set to 2-, 3-, or 4-wires. See Figure 5 on page 24 for

the wiring configuration.

7.2.1.6

Thermistor T(R) Conversion [THERM-T]

The following Steinhart-Hart equation is used for the thermistor T(R)

conversion:

T(r)[K ] = [A₀+ A₁lnr + A₂ln²r + A₃ln³r]⁻¹

The user-defined parameters for the thermistor T(R) conversion are A0 (A₀)

through A3 (A₃) as shown on a typical Hart Scientific thermistor calibration re-

port. If A₂is not used, as is the case with some calibrations, A2 should be set to

0.0.

Note: Thermistor coefficients stated on the thermistor calibration report may be

labeled differently. The best way to identify the coefficients to use with this

type is to match the equation above with the equation given on the calibration

report. Also, recognize that the coefficients for this equation generally have

negative exponents, e.g. A3: 1.39456E-07.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

When the Thermistor T(R) conversion type is selected, the coefficients are dis-

played on the right portion of the bottom of the display. Use the UD buttons

to scroll through the coefficients. Use the Enter button to edit and save the

new setting. Press and hold the Exit button to cancel to the main display or

press the EXIT button to cancel and to move to the next parameter. On the last

parameter, press the Exit button to exit to the menu.

7.2.1.7

Thermistor R(T) Conversion [THERM-R]

The following Steinhart-Hart equation is used for the thermistor R(T)

conversion:

r(T[K ]) = exp[B₀+ B₁T⁻¹+ B₂T⁻²+ B₃T⁻³

]

The user-defined parameters for the thermistor R(T) conversion are B0 (B₀)

through B3 (B₃) as shown on a typical Hart Scientific thermistor calibration re-

port. If B₂is not used, as is the case with some calibrations, B2 should be set to

0.0.

Note: Thermistor coefficients stated on the thermistor calibration report may be

labeled differently. The best way to identify the coefficients to use with this

type is to match the equation above with the equation given on the calibration

report. Also, recognize that the coefficients for this equation generally have

positive exponents, e.g. B3: -6.23659E+06.

When the Thermistor R(T) conversion type is selected, the coefficients are dis-

played on the right portion of the bottom of the display. Use the UD buttons

to scroll through the coefficients. Use the Enter button to edit and save the new

setting. Press and hold the Exit button to cancel to the main display or press the

EXIT button to cancel and to move to the next parameter. On the last parame-

ter, press the Exit button to exit to the menu.

7.2.1.8

7.2.1.9

YSI-400 Conversion

The YSI-400 conversion type is for 2252Ω thermistors matching the character-

istics of the YSI-400 series of thermistors.

There are no user programmable coefficients associated with this conversion

type. Use the Enter button or Exit button to exit the menu.

Thermocouple Volts [Vin[mV]]

The thermocouple volts displays the measurement in volts rather than

temperature.

Note: When selecting volts as the conversion type for thermocouples, no

cold-junction compensation is available. The value measured and displayed is

the uncompensated voltage as sensed at the input of the module.

There are no user programmable coefficients associated with this conversion

type. Use the Enter button or Exit button to exit to the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

7.2.1.10

Standard Thermocouple Conversions

Standard thermocouple conversions include types B, E, J, K, N, R, S, T, and

Au-Pt. Voltage is converted to temperature using standard reference functions.

(For additional information consult the publication NIST Monograph 175.)

You can specify internal or external reference junction compensation (RJC)

with the RJC parameter. (See Table 9 on page 129.) With internal RJC, the tem-

perature of the thermocouple cold junction is measured automatically and used

to calculate the absolute temperature of the thermocouple. With external RJC, a

reference junction at a known fixed temperature is used and the value of this

fixed temperature reference must be entered in the RJT parameter and is used

to calculate the absolute temperature of the thermocouple.

Conversions for each of the thermocouple types accept functional calibration

data. This can be used to improve the measurement accuracy. The parameter,

Tn, is the temperature of the point in degrees Celsius. The parameter, ADJn, is

the temperature deviation from the reference function at the point in degrees

Celsius. The temperature measurement is adjusted by this amount when mea-

suring at this temperature. A polynomial interpolation function is used for mea-

surements between calibration points. If calibration data is not available or is

not to be used, the ADJn parameters should all be set to 0.0. This causes the

temperature to be calculated according to the standard reference functions.

7.2.1.11

Thermocouple Polynomial Conversion

The thermocouple polynomial conversion allows calculation of temperature by

polynomial conversion.

When the Thermocouple Polynomial conversion type is selected, the coeffi-

cients are displayed on the right portion of the bottom of the display. Use the

UD buttons to scroll through the coefficients. Use the Enter button to edit

and save the new setting. Press and hold the Exit button to cancel to the main

display or press the EXIT button to cancel and to move to the next parameter.

On the last parameter, press the Exit button to exit to the menu.

The following equation is used for the thermocouple polynomial conversion:

t(E[mV])[°C ] = C_iEⁱ

∑

i = 0

The user-defined parameters for the thermocouple polynomial conversion are

the coefficients c₀(C0) through c₆(C6). The user can specify internal or exter-

nal reference junction compensation (RJC; see Table 9 on page 129). If external

RJC is selected, the user enters the temperature of the RJC reference in the ref-

erence junction temperature (RJT) parameter.

The output of the thermocouple, in millivolts, at 25°C with the reference junc-

tion at 0°C, is mV (25°C). For example, for a type K thermocouple, mV(25°C)

is 1.0002.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

7.2.2

Copy Probe

The COPY PROBE function allows you to copy a set of probe parameters from

one channel or memory location to another. The parameters are copied from the

user selected source channel or memory location into the current channel. The

COPY PROBE function can be password protected to restrict access. See Sec-

tion 7.5.3, Password, for more information. If this function is password pro-

tected, the user is prompted to enter the password to gain access. If an incorrect

password is entered, the display shows the message PASSWORD INCOR-

RECT and access is denied. If the correct password is entered or if this function

is not password protected, the bottom portion of the display appears showing

the source channel or memory location, the probe serial number, and the con-

version type. The destination channel or memory location is displayed after the

source channel type is selected.

24.159C 24.634C

24.142C 24.015C

FROM CH: PMEMO

TO CH: CHAN1

PT100

SERIAL:

TYPE:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 15 Copy Probe

Use the LR buttons to select the source channel or memory location. Press

the Enter button to save the new setting. Press the Exit button to cancel and to

exit to the menu.

7.2.3

Test Probe

The TEST PROBE function allows you to test the probe characterization algo-

rithm and characterization coefficients for a specific probe. The probe and

probe type must be setup in the EDIT PROBE function prior to entering the

TEST PROBE function. When this function is selected, the bottom portion of

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Probe Menu

the display shows the probe channel or memory location, the probe serial num-

ber, and the conversion type.

24.159C 24.634C

24.142C 24.015C

PROBE:

CHAN1

SERIAL:

TYPE:

145-560

CVD

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 16 Test Probe

Use the LR buttons to select the channel or memory location. After the

channel is selected, press the Enter button to test the temperature calculation

for the probe. You can enter an input value (Ω, KΩ, or millivolts) and the corre-

sponding output value (e.g. temperature) is shown. Press the Exit button to exit

to the menu.

7.2.4

Print Probe

The PRINT PROBE function allows you to print probe characteristics to a se-

lected port (either serial or IR). Probe characteristics for a specific channel or

memory location can be printed or for all channel and memory locations. When

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

this function is selected, the bottom portion of the display shows the probe

channel.

24.159C 24.634C

24.142C 24.015C

PROBE:

PORT:

CHAN1

SERIAL

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 17 Print Probe

Use the LR buttons to select the channel, memory location, or ALL. Use the

UD buttons to scroll between parameters. Press the Enter button to continue

and to send the data to the selected port. A message is displayed stating the

channel to print and the port. Press the Enter button to print the data. Press the

EXIT button to cancel and to exit to the menu.

7.2.5

Default Probe

The DEFAULT PROBE function allows you to reset the probe coefficients for a

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Fields Menu

selected channel, memory location, or ALL to the factory defaults. When this

function is selected, the bottom portion of the display shows the probe channel.

24.159C 24.634C

24.142C 24.015C

PROBE:

CHAN1

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 18 Default Probe

Use the LR buttons to select the channel, memory location, or ALL. Press

the Enter button to reset the probe coefficients. Press the Exit button to cancel

and to exit to the menu.

7.3

Fields Menu

The FIELDS menu allows for the programming and altering of the data dis-

played in the lower portion of the display. Commands in this menu allow the

user to select specific data fields to be displayed and stored by display sets. The

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

functions that appear in this menu are CLEAR STATS, SELECT FIELDS,

EDIT FIELDS, DEFAULT FIELDS, and DISPLAY OPTIONS.

24.159C 24.634C

24.142C 24.015C

DISPLAY CONFIGURATION FUNCTIONS

CLEAR

STATS

SELECT

FIELDS

EDIT

FIELDS

DEFAULT

FIELDS

DISPLAY

OPTIONS

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 20 Fields Menu

7.3.1

Clear Stats

The CLEAR STATS function clears the statistical registers and resets all statis-

tical calculations for all channels. Refer to Section 7.3.2, Select Fields, to dis-

play statistical data. When this function is selected, the bottom portion of the

display states that you must press the Enter button to clear the statistical data.

24.159C 24.634C

24.142C 24.015C

CLEAR STATISTICAL DATA.

Press ENTER to continue...

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 19 Clear Stats

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Fields Menu

Press the Enter button to clear the statistical data. Press the Exit button to abort

clearing the statistical data and to exit to the menu.

7.3.2

Select Fields

The SELECT FIELDS function allows you to select a display set (1 through 9)

to use for displaying information provided by the instrument. A display set can

be customized to display up to eight different fields. See the table of Field

Types below. When this function is selected, the bottom portion of the display

allows you to select the display set and also shows the information that is dis-

played for each set. To edit a display set, see Section 7.3.3, Edit Fields.

24.159C 24.634C

24.142C 24.015C

[1]*

[2]*

[3]*

[4]*

[5]*

[6]*

[7]*

[8]*

TYP

SER

-T1

AVE

STD

SPR

TIME

DISPLAY:

ALOG

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 21 Select Fields

Use the LR buttons to select the display set number. Press the Enter button

to save the new setting and exit. Press the Exit button to cancel and to exit to

the menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Keyword

AVE

Field Type

Average

BATT

DATE

INP

Battery Percent Remaining

Date

Input in ohms, K ohms, or mV

MAX

Maximum

MEAS

MIN

Number of Seconds Until Next Measurement

Minimum

REF

Reference (see below)

SER

Probe Serial Number

SPR

Spread

STD

Standard Deviation

STN

Count

-T1, -T2, -T3, -T4

TEM

Delta

Temperature

TIME

TYP

Time

Conversion Type

ALOG

----

Indicating of auto logging is on or off

Blank

Note: When the field type reference (REF) is selected, the displayed keyword

changes depending on the probe type. The reference display keywords are de-

tailed in the following table.

REF Display Keywords

Probe Type

Keyword

RIN

Description

Resistance

R(0.01°C)

RES

ITS-90

RTP

ITS-SR5

PT-100

CVD

R(0°C)

THERM-R

THERM-T

YSI-400

R25

R(25°C)

VIN[mV]

Thermocouples

RJT

Reference Junction

Temperature

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Fields Menu

7.3.3

Edit Fields

The EDIT FIELDS function allows editing of the display fields for a given dis-

play set (1 through 9). You can choose to display one to eight fields. The avail-

able fields and their corresponding keywords are given in the Field Types table

above. When this function is selected, the bottom portion of the display allows

you to select the display set to edit.

24.159C 24.634C

24.142C 24.015C

[1]*

[2]*

[3]*

[4]*

[5]*

[6]*

[7]*

[8]*

TYP

SER

-T1

AVE

STD

SPR

TIME

DISPLAY:

ALOG

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 22 Edit Fields

The rightmost portion of the bottom of the display shows the current settings

for the eight fields for the selected display set. The field numbers appear in the

square brackets ([]) and are not editable. The character immediately to the right

of the field number is editable and indicates the channel (‘*’, or 1 through 4). If

the ‘*’ is selected and you are in simultaneous mode, channel one is displayed.

If you are in scan mode, selecting the ‘*’ displays the current channel. The field

item is editable and is to the right of the channel. The table of Field Types

above shows the keywords for each type of field item.

Press the LR buttons to select the display set. Press the Enter button to se-

lect the field parameters (channel and field type) to adjust. Use the LR but-

tons to adjust the parameter value. Use the UD buttons to move between

parameters. Press the Exit button to exit to the menu.

7.3.4

Default Fields

The DEFAULT FIELDS function clears all display sets and resets them to the

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

factory defaults. When this function is selected, the bottom portion of the dis-

play instructs you to press Enter to revert to the default display set.

24.159C 24.634C

24.142C 24.015C

REVERT TO DEFAULT DISPLAY SETUP.

Press ENTER to continue...:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 23 Default Fields

Press the Enter button to revert to the default display setup. Press the Exit but-

ton to exit to the menu.

7.3.5

Display Options

The DISPLAY OPTIONS function allows you to select the display resolution,

decimal character, and lamp illumination. When this function is selected, the

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

bottom portion of the display shows the current display settings. This function

is the same as the CHANNEL MODE menu DISPLAY OPTIONS function.

24.159C 24.634C

24.142C 24.015C

RESOL:

DECIMAL:

LAMP:

OFF

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 24 Display Options

The RESOL parameter determines the number of decimal places (0 through 4

or AUTO) to be displayed for the temperature measurements. If AUTO is se-

lected, the instrument automatically determines the number of decimal places

to display depending on the conversion type.

The DECIMAL parameter is for selecting the character used as the decimal

separator. The choices are period (.) or comma (,).

The LAMP parameter specifies the brightness of the display (OFF, LOW,

MED, HIGH). Enabling this parameter causes the battery to discharge faster.

Press the LR buttons to select the parameter setting. Use the UD buttons

to scroll between the parameters. Press the Enter button to save the new set-

ting. Press the Exit button to cancel and to exit to the menu.

7.4

Logging Menu

The LOGGING menu provides functions for logging measurements on demand

and automatically, displaying log statistics, editing data labels, and resetting the

data labels to their default values. The submenus and functions that appear in

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

this menu are DEMAND LOG, AUTO LOG, LOG STATS, DATA LABELS,

and DEFAULT LABELS.

24.159C 24.634C

24.142C 24.015C

DATA RECORDING FUNCTIONS

DEMAND

LOG

AUTO

LOG

STATS

DATA

LABELS

DEFAULT

LABELS

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 25 Logging Menu

7.4.1

Demand Log

The DEMAND LOG submenu allows measurements to be logged on demand,

one reading at a time. Readings are stored to the instrument's memory and as-

signed a label for easy recall and organization of data. The instruments memory

can store up to 100 demand log readings.

Demand log values are stored exactly as they appear on the upper portion of the

display. The resolution, temperature units, and the channels displayed should

be set up prior to demand logging in order to ensure proper storage of data.

When this function is selected, the bottom portion of the display shows the de-

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

mand logging submenu which consists of the functions: STORE READING,

LOG HISTORY, VIEW DATA, PRINT DATA, and DELETE DATA.

24.159C 24.634C

24.142C 24.015C

DEMAND LOGGING FUNCTIONS

STORE

READING

LOG

HISTORY

VIEW

DATA

DELETE

DATA

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 26 Demand Log Submenu

7.4.1.1

Store Reading

The STORE READING function stores the current measurements for all dis-

played channels. When the instrument is in simultaneous mode, all channels

that are displayed on the upper portion of the 1529 display are stored simulta-

neously to the demand log. When the instrument is in scan mode, the channel

currently displayed on the upper portion of the 1529 display is the only mea-

surement that is stored to the demand log. For more information on the display

modes see Section 8.1.3, Channel Mode.

When the STORE READING function is selected, the left side of the bottom

portion of the display shows each channel, the measurement value (using the

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

current resolution setting), and the units as they are stored into memory. The

right side of the bottom display shows the current label.

24.159C 24.634C

24.142C 24.015C

CH 1

24.150 C

CH 2

CH 3

CH 4

29.634 C

24.010 C

23.989 C

DATA_01

LABEL:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 27 Store Readings

To change the label, press the LR buttons to scroll through and select the la-

bel that applies to the demand log data being stored. For information on editing

the labels see the DATA LABELS function of the LOGGING menu, Section

7.4.4.

After selecting the correct label, press the Enter button to store the label and

measurement(s) to memory. Press the Exit button to cancel and to return to the

DEMAND LOG menu.

7.4.1.2

Log History

The LOG HISTORY function displays the reading number, label, time, and

date of each demand log entery in sequential order. To see the measurement

values for each entry, use the DEMAND LOG menu VIEW DATA function.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

When this function is selected, the bottom portion of the display shows the de-

mand log history data.

24.159C 24.634C

24.142C 24.015C

01:

DATA_01

11:39:04

10-12-00

02:

03:

04:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 28 Log History

Press the UD buttons to scroll up and down through the stored readings se-

quentially one at a time. Press the LR buttons to scroll up and down through

the stored readings sequentially by groups of 16. Press the Enter or Exit button

to return to the DEMAND LOG menu.

7.4.1.3

View Data

The VIEW DATA function displays the reading number, label, channel, mea-

surement value, units, and time (24 hour time format) of each demand log en-

try. To see the corresponding date, use the DEMAND LOG menu LOG

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

HISTORY function. When this function is selected, the bottom portion of the

display shows the demand log data.

24.159C 24.634C

24.142C 24.015C

01:

DATA_01

24.156 C

29.629 C

24.086 C

24.048 C

11:39:04

02:

03:

04:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 29 Demand Log View Data

Press the UD buttons to scroll up and down through the stored readings se-

quentially. Press the LR buttons to scroll up and down through the stored

readings sequentially by groups of 16. Press the Enter or Exit button to return

to the DEMAND LOG menu.

7.4.1.4

Print Data

The PRINT DATA function prints the demand log data for the selected label or

for all labels. The demand log data is printed to the selected port (either serial

port or IR port). When this function is selected, the bottom portion of the dis-

play allows you to select the label of the demand log data to print or all data

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

and the port. Select ALL DATA to print all demand log entries, or select a spe-

cific label to print only the demand log data for that label.

24.159C 24.634C

24.142C 24.015C

LABEL:

PORT:

ALL DATA

SERIAL

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 30 Print Data

Use the LR buttons to select the parameter settings. Use the UD buttons to

scroll between parameters. Press the Enter button to continue. A message is

displayed stating the label of the data to print and the port. Press the Enter but-

ton to print the data. Press the EXIT button to cancel and to exit to the menu.

7.4.1.5

Delete Data

The DELETE DATA function deletes the demand log data for a selected label

or for all labels. When this function is selected, the bottom portion of the dis-

play allows the user to select the label of the demand log data to delete or all

data. If readings for one label are deleted, the remaining entries are renum-

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

bered. Select ALL DATA to delete all demand log readings or select a specific

label to delete only the demand log data for that label.

24.159C 24.634C

24.142C 24.015C

DELETE:

ALL DATA

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 31 Delete Data

Use the LR buttons to select the label of the data you want to delete. Press

the Enter button to continue and delete the data. Press the Exit button to can-

cel and return to the DEMAND LOG menu.

7.4.2

Auto Log

The AUTO LOG function allows measurements to be logged automatically in

user-selectable intervals. Readings are stored to the instrument's memory and

assigned a label for easy recall and organization of data. The instruments mem-

ory can store up to 8,160 auto log readings.

Auto log values are stored exactly as they appear on the upper portion of the

display. The resolution, units, and the channels displayed should be set up prior

to auto logging in order to ensure proper storage of data. All displayed chan-

nels are stored during an auto log session. If the upper portion of the display is

changed while data is being auto logged, the data collected is modified from

the time the display was changed. For example, if a channel is disabled while

auto logging, that channel stops being stored from the time it was disabled.

When this function is selected, the bottom portion of the display shows the

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

AUTO LOG submenu and consists of the functions: LOGGING OPTIONS,

START STOP, VIEW DATA, PRINT DATA, and DELETE DATA.

24.159C 24.634C

24.142C 24.015C

AUTOMATIC LOGGING FUNCTIONS

LOGGING

OPTIONS

START

STOP

VIEW

DATA

DELETE

DATA

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 33 Auto Log Submenu

7.4.2.1

Logging Options

The LOGGING OPTIONS function allows the user to define the logging pa-

rameters. When this function is selected, the bottom portion of the display

prompts the user to select the label, period, and count.

24.159C 24.634C

24.142C 24.015C

DATA_01

LABEL:

LOG PER: 1 SEC

COUNT:

8000

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 32 Logging Options

The LABEL parameter specifies the label for the auto log data. The labels are

defined in the DATA LABELS function of the LOGGING menu or reset to the

default labels in the DEFAULT LABELS function of the LOGGING menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The LOG PER parameter is for selecting the interval between measurements.

You may select between 0.1, 0.2, 0.5, 1, 2, 5, 10, and 30 seconds, 1, 2, 5, 10,

and 30 minutes or 1 hour. The LOG PER must be set to a value less than or

equal to the measurement period. The 1529 will not log readings faster than the

measurement period. The measurement period is set in the MEASURE PE-

RIOD function of the CHANNEL menu and is the rate at which readings are

taken.

If the log period is set to a value less than the measure period the following

message is displayed in the lower portion of the display.

DATA WILL BE LOGGED NO FASTER THAN

THE MEASURE PERIOD (X SEC ).

Press ENTER to continue…

The X in the message is the current measurement period. After the Enter but-

ton is pressed, the measurements are logged at the current measure period.

The COUNT parameter is for selecting the total number of readings to log. The

default is 8,160, which is the maximum number of readings that can be logged.

If the count is set to 10 and two channels are displayed on the screen at the time

logging starts, five readings from each channel are logged for a total of 10 read-

ings. The auto log automatically stops after the number of readings selected is

reached or when the user stops the log manually.

Press the LR buttons to change a setting and the UD buttons to scroll be-

tween the parameters. Press Enter button to save the new setting. Press and

hold the Exit button to cancel to the main display or press the EXIT button to

cancel and to move to the next parameter.

7.4.2.2

Start Stop

The START STOP function starts and stops auto log sessions. When this func-

tion is selected, the user is prompted to either start or stop an auto log session

by pressing the Enter button. If an auto log session is not currently running,

the user is prompted to START RECORDING DATA. If an auto log session is

running, the user is prompted to STOP RECORDING DATA.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

Note: The log is not started or stopped until the Enter button is pressed to con-

firm the user action.

24.159C 24.634C

24.142C 24.015C

START RECORDING DATA.

Press ENTER to continue...

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 35 Start Stop

After a log session is started, the bottom portion of the display shows the log

statistics. These statistics can also be viewed from the LOG STATS function of

the LOGGING menu.

24.159C 24.634C

24.142C 24.015C

DEMAND LOG

AUTO LOG

COUNT: 6494

FILLED: 18.5%

FREE: 6654, 1506

FILLED: 4.0%

FREE: 95, 4

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 34 Log Statistics (Auto Log Started)

The left side displays demand log statistics and the right side displays the auto

log statistics. The FILLED parameter shows the percentage of the total demand

or auto log memory that is currently filled. The FREE parameter shows the

number of readings remaining before the memory is full and the number of

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

readings currently stored in the demand or auto log memory. The COUNT pa-

rameter shows the number of auto log readings remaining during the current

log session.

Press the Enter or Exit button to exit this display and to return to the AUTO

LOG menu.

Only those channels that are enabled during the log session are logged. Al-

though you may enable and disable channels during a log session we do not

recommend this practice. If channels are disabled during the log session, the

previously logged entries for those channels are not removed from the log.

From the main display, there are two ways to tell if data is being logged: (1) a

logging indicator in the lower left-hand corner (looks like a strip-chart) and (2)

by setting one of the display fields to the ALOG type (see Section 8.3.3, Edit

Fields)

7.4.2.3

View Data

The VIEW DATA function displays the label, date, reading number, channel,

measurement, units, and time of each auto log entry in sequential order. When

this function is selected, the bottom portion of the display shows the auto log

data.

24.159C 24.634C

24.142C 24.015C

DATA_01

0002: 1

10-12-00

24.147 C

29.637 C

23.972 C

12:23:24

0003:

0004: 3

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 36 Auto Log View Data

Each time the view data function is accessed the current auto log memory is

displayed. The data is updated each time the function is accessed; it is not up-

dated continuously during a log session.

The entries are grouped by the label specified and displayed in the order that

they were logged. For each log session, an entry is written into the log, which

includes the label for all readings in that session and the date of the session.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

Subsequent entries in the log consist of the reading number, channel, measure-

ment value, units, and the time of each entry.

Press the LR buttons to jump 100 readings at a time. Hold the UD buttons

down to advance quickly through the data. Press and hold the L button to

view the top reading, and the R button to view the bottom reading. Press the

Enter or Exit button to return to the AUTO LOG menu.

7.4.2.4

Print Data

The PRINT DATA function prints the auto log data for the selected label or for

all labels. The auto log data is printed to the selected port (either serial port or

IR port). When this function is selected, the bottom portion of the display al-

lows you to select the label of the auto log data or all data and the port. Select

ALL DATA to print all auto log entries, or select a specific label to print only

the auto log data for that label.

24.159C 24.634C

24.142C 24.015C

LABEL:

PORT:

ALL DATA

SERIAL

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 37 Print Data

Use the LR buttons to select the parameter settings. Use the UD buttons to

scroll between parameters. Press the Enter button to continue. A message is

displayed stating the label of the data to print and the port. Press the Enter but-

ton to print the data. Press the EXIT button to cancel and to exit to the menu.

7.4.2.5

Delete Data

The DELETE DATA function deletes the auto log data for the selected label or

for all labels. When this function is selected, the bottom portion of the display

allows the user to select the label of the auto log session to delete or all data.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Select ALL DATA to delete all auto log readings or select a specific label to de-

lete only the auto log entries for that label.

24.159C 24.634C

24.142C 24.015C

DELETE:

ALL DATA

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 38 Delete Data

Use the LR buttons to select the label of the data you want to delete. Press

the Enter button to continue and to delete the data. Press the Exit button to

cancel and to return to the AUTO LOG menu.

7.4.3

Log Stats

The LOG STATS function displays the number of measurements logged, the

percentage of memory used, and the number of measurements to be logged for

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

Logging Menu

both the demand and auto logs. When this function is selected, the bottom por-

tion of the display shows the logging statistics.

24.159C 24.634C

24.142C 24.015C

DEMAND LOG

AUTO LOG

COUNT: 6655

FILLED: 18.5%

FREE: 6654, 1506

FILLED: 4.0%

FREE: 95, 4

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 39 Log Stats

The left side displays demand log statistics and the right side displays the auto

log statistics. The FILLED parameter shows the percentage of the total demand

or auto log memory that is currently filled. The FREE parameter shows the

number of readings remaining before the memory is full and the number of

readings currently stored in the demand or auto log memory. The COUNT pa-

rameter is only displayed when an auto log session is running. This parameter

shows the number of auto log readings remaining during the current log

session.

Press the Enter or Exit button to exit this display and to return to the

LOGGING menu.

7.4.4

Data Labels

The DATA LABELS function allows 25 demand log and auto log labels to be

edited. When this function is selected, the bottom portion of the display allows

the user to select the data label to edit. The labels contain up to 8 alphanumeric

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

digits. These labels are used to identify logged data when using the demand

and auto log functions.

24.159C 24.634C

24.142C 24.015C

SELECT:

DATA_01

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 40 Data Labels

Press the LR buttons to select the label to edit. By default the labels are set

to DATA_01, DATA_02, … at the factory. Press the Enter button to begin edit-

ing the label. The word SELECT changes to EDIT, and the label can now be

edited. Press the LR buttons to highlight the character you want to change.

Use the UD buttons to scroll through the letters A-Z, numbers 0-9, and under-

score (_). The blank space causes all characters to the right to be deleted when

the Enter button is pressed.

Press the Enter button to store the new label or press the Exit button to cancel

and to return to the menu.

7.4.5

Default Labels

The DEFAULT LABELS function resets the data labels to their default settings.

By default the labels are set to DATA_01, DATA_02, … at the factory. When

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

System Menu

this function is selected, the bottom portion of the display instructs the user to

press the Enter button to reset the data labels to their default settings.

24.159C 24.634C

24.142C 24.015C

RESET DATA LABELS TO DEFAULTS.

Press ENTER to continue...

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 41 Default Labels

To exit without resetting the labels, press the Exit button.

7.5

System Menu

The SYSTEM menu provides functions for the communication ports, the date

and time format, the password, the calibration, and system reset. When entering

the SYSTEM menu, the instrument’s model number, manufacturer, firmware

version, and serial number are displayed above the menu. The functions that

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

appear in this menu are COMM SETUP, DATE TIME, PASSWORD, CALI-

BRATION, and SYSTEM RESET.

24.159C 24.634C

24.142C 24.015C

1529 HART 0.50 SERNUM

COMM

SETUP

DATE

TIME

PASS-

WORD

CALI-

BRATION

SYSTEM

RESET

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 42 System Menu

7.5.1

Comm Setup

The COMM SETUP function is used to setup the communication parameters

for the installed ports. Communications ports are used for communicating with

a computer, printer, or other equipment. When this function is selected, the bot-

tom portion of the display prompts the user to select the communication port to

setup. The 1529 thermometer readout is shipped standard with one serial

(RS-232) port and one IR port. A GPIB port may optionally be installed. The

GPIB port selection only appears if it is installed. ERRORS may also be se-

lected for the port. This port selection allows the user to view any error mes-

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

System Menu

sages stored in the error queue on the display. Once an error has been viewed, it

is removed from the error queue.

24.159C 24.634C

24.142C 24.015C

PORT:

SERIAL

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 43 Comm Setup

Press the LR buttons to select the port to setup. Press the Enter button to

display the port parameters.

7.5.1.1

Serial

When the SERIAL option is selected, the parameters for the serial port are dis-

played on the bottom portion of the display. These parameters are: BAUD, SER

PER, LF, PRINT, and ECHO.

The BAUD parameter allows the user to select the baud rate for communica-

tions on this port. The user may choose between 1200, 2400, 4800, 9600, and

19200. The default baud rate is 9600.

The SER PER parameter allows the user to select the interval at which mea-

surements are transmitted over the serial port. The user may choose between

0.1, 0.2, 0.5, 1, 2, 5, 10, and 30 seconds, 1, 2, 5, 10, and 30 minutes, and 1

hour.

The LF parameter allows the user to specify whether a linefeed character

(ASCII 0A hex or 10 decimal) is appended to the end of each line transmitted

over the serial port. Selecting ON sends both a carriage return (ASCII 00 hex or

13 decimal) and a linefeed. Selecting OFF sends only a carriage return.

The PRINT parameter allows the user to enable printing measurements over the

serial port. Selecting ON enables printing and selecting OFF disables printing.

With slower MEA PER (see Section 7.1.1) and SER PER rates of 1 second or

more, measurements are printed with the channel number, measured value,

unit, time, and date, all separated with spaces. With faster rates, less than 1

second, only the measured value is printed.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The ECHO parameter allows the user to set the echo (duplex) mode. Selecting

ON enables echoing so that all characters received on the serial port are echoed

back over the serial port. This mode is useful when using terminal emulation

software on a computer to communicate with the instrument. Selecting OFF

disables echoing. This mode is commonly used when using control software on

the computer.

Press the LR buttons to select the parameter setting. Use the UD buttons

to scroll between the parameters. Press the Enter button to save the new set-

ting. Press and hold the Exit button to cancel to the main display or press the

EXIT button to cancel and to move to the next parameter.

7.5.1.2

When the IR option is selected, the parameters for the IR port are displayed on

the bottom portion of the display. These parameters are: MODE, IR PER, and

PRINT.

The MODE parameter allows the user to select the protocol used by the IR port

to transmit and receive data. The user may choose between OFF, HP-PR,

COMM, and IRDA.

The OFF option turns the IR port off.

The HP-PR option allows the user to print a new measurement to an

HP-IR calculator printer.

The COMM option allows the user to transmit data over the IR port at

9600 baud in simple ASCII format.

The IRDA option allows the user to print logged data to an IrDA compati-

ble printer (such as an HP LaserJet 2100). Automatic real time printing is

not possible with the IrDA mode..

The IR PER parameter allows the user to select the interval at which measure-

ments are transmitted over the serial port. The user may choose between 0.1,

0.2, 0.5, 1, 2, 5, 10, and 30 seconds, 1, 2, 5, 10, and 30 minutes, and 1 hour.

The IR PER can not be set to less than 10 seconds if the MODE is set to

HP-PR.

The PRINT parameter allows the user to enable printing measurements over the

IR port. Selecting ON enables printing and selecting OFF disables printing.

Press the LR buttons to select the parameter setting. Use the UD buttons

to scroll between the parameters. Press the Enter button to save the new set-

ting. Press and hold the Exit button to cancel to the main display or press the

EXIT button to cancel and to move to the next parameter.

7.5.1.3

GPIB (Optional)

When the GPIB option is selected, the parameters for the IEEE-488 port are

displayed on the bottom portion of the display. These parameters are: GPIB,

ADDR, and TERM.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

System Menu

The GPIB parameter allows the user to enable or disable the IEEE-488 port.

The ADDR parameter allows the user to specify the address of this instrument

on the IEEE-488 bus. The default address is 22 and the range is 1 to 30.

The TERM parameter allows the user to select the termination character trans-

mitted after each transmission. The default termination character is linefeed

(LF).

7.5.2

Date Time

The DATE TIME function is used for setting the time-of-day clock, time for-

mat, date, and date format. When this function is selected, the bottom portion

of the display shows the hour, minute, second, time format, day, month, year,

and date format.

24.159C 24.634C

24.142C 24.015C

HOUR:

DAY:

MINUTE:

SECOND:

T FORM:

MONTH:

YEAR:

D FORM:

2000

M-D-YY

24 HR

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 44 Date Time

The HOUR parameter allows the user to set the current hour (0 through 23).

The MINUTE parameter allows the user to set the current minutes (0 through

59).

The SECOND parameter allows the user to set the current seconds (0 through

59).

The T FORM parameter allows the user to set the time format used for display-

ing the time. The choices are 12-hour format or 24-hour format.

The DAY parameter allows the user to set the current day (1 through 31).

The MONTH parameter allows the user to set the current month (1 through

12).

The YEAR parameter allows the user to set the current year (1999 through

9999).

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The D FORM parameter allows the user to set the date format used when dis-

play the date. The choices are M-D-YY, M-D-YYYY, D/M/YY, and

D/M/YYYY.

Press the LR buttons to change the parameter setting. Use the UD buttons

to scroll between the parameters. Press the Enter button to save the new set-

ting. Press the Exit button to exit to the menu.

7.5.3

Password

The PASSWORD function is used for changing the password required for ac-

cess to password-protected parameters and to determine whether to pass-

word-protect certain parameters. When this function is selected, the bottom

portion of the display prompts the user to enter the current password to gain ac-

cess to this function.

24.159C 24.634C

24.142C 24.015C

ENTER CORRECT PASSWORD FOR ACCESS.

PASSWRD:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 45 Password

By default the password is set to '1529' when the instrument ships from the fac-

tory. We recommend that the user change the default password to protect the

password-protected settings. Note: Keep your password in a secure location

and do not forget it.

To enter the password, press the Enter button. Press the LR buttons to high-

light the digit you want to change. Use the UD buttons to scroll through the

numbers 0-9 to set each digit of the password. Press the Enter button to accept

the password or press the Exit button to cancel and to exit to the menu.

If an incorrect password is entered, the display shows the message PASS-

WORD INCORRECT and access to the password-protected parameters is de-

nied. Press the Enter button to return to the menu. If the correct password is

entered, the password-protected parameters are displayed in the bottom portion

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

System Menu

of the display. The password-protected parameters are PASSWRD and PRB

SEC.

The PASSWRD parameter allows the user to change the password. Press the

Enter button to edit the PASSWRD parameter. Press the LR buttons to

highlight the digit to change. Use the UD buttons to scroll through the num-

bers 0-9. Press the Enter button to save the new setting. Press the Exit button

to cancel and to move to the next parameter or to exit to the menu. Note: Keep

your password in a secure location and do not forget the password.

The PRB SEC parameter allows the user to password protect the EDIT PROBE

and COPY PROBE functions of the PROBE menu (see Sections 8.2.1, Edit

Probe and 8.2.2, Copy Probe). If this parameter is set to ON, the user must en-

ter the correct password when entering the EDIT PROBE and COPY PROBE

functions. If this parameter is set to OFF, a password is not required when en-

tering these functions. Press the LR buttons to change the parameter setting.

Press the Enter button to save the new setting. Press the Exit button to cancel

and to exit to the menu.

7.5.4

Calibration

The CALIBRATION function is used for accessing parameters and functions

related to the 1529 calibration. It first displays the date the current calibration is

due and the date the instrument should be recalibrated. Typically, all channels

should have the same due date. However, in the case that all channels do not

have the same due date the earliest date is displayed. This function is pass-

word-protected (see Section 7.5.3). In order to access the parameters within this

function you must enter the correct four-digit password. When this function is

selected, the bottom portion of the display prompts the user to enter the current

password to gain access to this option.

24.159C 24.634C

24.142C 24.015C

ENTER CORRECT PASSWORD FOR ACCESS.

PASSWRD:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 46 Password for Calibration Access

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

By default the password is set to ‘1529’ when the instrument ships from the

factory. We recommend that the user change the default password to protect the

password-protected settings. Note: Keep your password in a secure location

and do not forget it.

To enter the password, press the Enter button. Press the LR buttons to high-

light the digit to change. Use the UD buttons to scroll through the numbers

0-9. Press the Enter button to save the new setting. Press the Exit button to

cancel and to exit to the menu.

If an incorrect password is entered, the display shows the message PASS-

WORD INCORRECT and access to the password-protected parameters is de-

nied. Press the Enter button to return to the menu. If the correct password is

entered, the bottom portion of the display allows the user to select the channel

to view.

24.159C 24.634C

24.142C 24.015C

CAL CH:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 47 Select Calibration Channel

Each channel of the 1529 is calibrated independently and therefore each chan-

nel has its own set of calibration parameters which are displayed after the CAL

CH parameter is entered.

Use the LR buttons to select the channel. Press the Enter button to view the

calibration parameters for the selected channel. Press the Exit button to cancel

and to exit to the menu.

For PRT/thermistor channels, the parameters C0, C100, C400, C0K, C10K,

C100K, DATE, and DUE are displayed.

The C0, C100, and C400 parameters apply to the PRT probe types and

100Ω resistance range. Use these parameters to adjust the measurement at

0, 100 and 400Ω respectively. These values are in ohms.

Download from Www.Somanuals.com. All Manuals Search And Download.

7 Menu Functions

System Menu

The C0K, C10K, and C100K parameters apply to the thermistor probe

types and 10KΩ resistance range. Use these parameters to adjust the mea-

surement at 0K,10K, and 100KΩ respectively. These values are in Kohms.

The DATE parameter is the date the current calibration was performed.

The DUE parameter is the date the current calibration expires.

For thermocouple channels, the parameters C0, C100, CRJ, DATE, and DUE

are displayed.

The C0 and C100 parameters adjust the measurement at 0 and 100 mV re-

spectively. These values are in mV.

The CRJ parameter adjusts the reference junction temperature measure-

ment. This parameter is in °C.

The DATE parameter is the date the current calibration was performed.

The DUE parameter is the date the current calibration expires.

Press the LR buttons to change a setting and the UD buttons to scroll be-

tween parameters. Press the Enter button to save the new setting. Press the

Exit button to exit to the menu.

7.5.5

System Reset

The SYSTEM RESET function resets all operating parameters to the factory

default values. This function is password-protected (see Section 7.5.3, Pass-

word). In order to access the system reset, you must enter the correct four-digit

password. When this function is selected, the bottom portion of the display

prompts the user to enter the current password to gain access to this option.

24.159C 24.634C

24.142C 24.015C

ENTER CORRECT PASSWORD FOR ACCESS.

PASSWRD:

CHUB E-4 THERMOMETER READOUT

1529

EXIT

ENTER / MENU

UNIT

CONTRAST

Figure 48 Pass Cal Reset

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

By default the password is set to ‘1529’ when the instrument ships from the

factory. We recommend that the user change the default password to protect the

password-protected settings. Note: Keep your password in a secure location

and do not forget it.

To enter the password, press the Enter button. Press the LR buttons to high-

light the digit to change. Use the UD buttons to scroll through the numbers

0-9. Press the Enter button to save the new setting. Press the Exit button to

cancel and to exit to the menu.

If an incorrect password is entered the display shows the message PASSWORD

INCORRECT and access to the password-protected parameters is denied. Press

the Enter button to return to the menu. If the correct password is entered, the

bottom portion of the display instructs the user to press Enter to reset the set-

tings to the defaults.

The system reset does the following:

• Sets the measure period to 1 second.

• Sets channel 1 ON, all others OFF.

• Sets the channel mode to SCAN.

• Sets moving average to 1.

• Sets printing to all ports OFF.

• Stops auto logging.

• Clears the statistical functions.

• Sets units to C.

• Sets the resolution to AUTO.

Reset does not affect any of the probe characterization parameters, logged data

or channel calibration parameters.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Overview

Digital Communications Interface

8.1

Overview

The communication feature allows an external device, such as a computer, to

communicate with the 1529 to obtain measurement data and control operating

conditions. Communication is accomplished by issuing commands to the 1529

through RS-232, IR, or IEEE-488 communication ports.

8.2

Communications

The thermometer readout is equipped with an RS-232 serial interface, an infra-

red window, and optionally a GPIB port. The serial interface allows communi-

cations up to distances of approximately 50 feet. The IR interface allows

communications up to distances of 1 foot. The serial interface, infrared win-

dow, and GPIB port allow the user to access the functions, parameters, and set-

tings discussed in Section 7, Menu Functions.

8.2.1

Serial Wiring

The serial communica-

tions cable attaches to the

thermometer readout

through the DB-9 connec-

tor at the back of the in-

strument. Figure 49 shows

the pin-out of this connec-

tor and suggested cable

wiring. This type of cable

is typically referred to as a

“null modem” cable. To

eliminate noise, the serial

cable should be shielded

with low resistance be-

tween the connector

(DB9) and the shield.

The serial period, baud

rate, linefeed, and echo

are programmable. Refer

to Section 7.5.1.1, Serial

Port, for instructions on

accessing and setting

these parameters.

Figure 49 Serial Cable Wiring

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

All commands sent to the 1529 through the serial interface must be terminated

with a carriage return or linefeed character.

8.2.2

GPIB Communications

The GPIB interface allows the Model 1529 to be connected to an IEEE-488 bus

along with other instruments. A system controller can remotely control the op-

eration of the Model 1529 and read measurements.

8.2.2.1

Capability

The Model 1529 GPIB interface conforms to standard IEEE-488.2, 1992. Its

capabilities are identified as SH1, AH1, T6, L4, SR1, DC1, and E2. The inter-

face has the capabilities of talk, listen, serial poll, and device clear. There is no

capability for talk-only, listen-only, extended talk or listen, parallel poll, re-

mote-local control, or trigger nor can it act as a controller. The IEEE-488 com-

mands GET, GTL, LLO, and REN are accepted without error but ignored.

8.2.2.2

8.2.2.3

Connection

The IEEE-488 port is located on the back of the 1529. Use a standard

IEEE-488 cable to connect to your GPIB controller. A shielded cable should be

used to prevent EM emission.

Device Setup

The Model 1529 system must be set up to respond to the controller address.

Refer to Section 7.5.1.3, GPIB, for setting address and other parameters for the

IEEE-488 port.

8.3

Interface Commands

8.3.1

Command Summary

An alphabetical listing of the commands implemented by the 1529 are shown

in Table 3 starting on page 81. These commands can be used with either serial,

IR, or IEEE-488 communications ports.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Interface Commands

Table 3 Alphabetical List of Commands

Command

Description

Refer To

*CLS

Clears the status registers

Section 8.4.12

*ESE?

Returns the Event Status Enable Register

Sets the Event Status Enable Register

Returns the Event Status Register

Section 8.4.12

Section 8.4.8

*ESE <num>|MIN|MAX|DEF

*ESR?

*IDN?

Returns the instrument identification string that indicates

the manufacturer, model number, serial number, and firm-

ware version

*OPT?

*RST

Returns a list of installed input card types

Section 8.4.8

Sets the instrument operating parameters to defined

conditions

*SRE?

Returns the Service Request Enable Register

Sets the Service Request Enable Register

Returns the Status Byte Register

Section 8.4.12

*SRE <num>|MIN|MAX|DEF

*STB?

*TST?

Performs a self-test and reports any errors that are found Section 8.4.12

Clears the statistical functions for all channels Section 8.4.1

CALCulate:AVERage:CLEar

CALCulate<chn>:AVERage<n>:DATA?

Returns the value of a statistical calculation for the speci- Section 8.4.1

fied channel

CALCulate:AVERage<n>:TYPE?

Returns the keyword for the specified calculation type

number

Section 8.4.1

Section 8.4.4

CALCulate<chn>:CONVert:CATalog?

CALCulate<chn>:CONVert:COPY<dest chn>|ALL

Returns a list of conversion types available for the speci-

fied channel

Copies the conversion type, sub-ranges (ITS-90), serial

number, and characterization coefficients from one chan-

nel to another

CALCulate<chn>:CONVert:NAMe?

Returns the name of the selected conversion type for the

specified channel

Section 8.4.4

CALCulate<chn>:CONVert:NAMe <conv>

CALCulate<chn>:CONVert:PARameter:CATalog?

Sets the conversion type by name for the specified

channel

Returns the names of the probe characterization parame- Section 8.4.4

ters used with the selected conversion type for the speci-

fied channel

CALCulate<chn>:CONVert:PARameter:VALue?

[<param>|ALL]

Returns the value for the specified or All conversion pa-

rameters for the specified channel

Section 8.4.4

CALCulate<chn>:CONVert:PARameter:VALue

<param>,<num>[,< param>,<num>...]

Sets the value of one or more conversion parameters for

the specified channel number

CALCulate:CONVert:PRINt [<chn>|ALL [,<port>]]

Returns the conversion parameters for the specified

channel

CALCulate<chn>:CONVert:SNUMber?

Returns the probe serial number for the specified channel Section 8.4.4

Sets the probe serial number for the specified channel Section 8.4.4

Tests the temperature conversion for the specified channel Section 8.4.4

CALCulate<chn>:CONVert:SNUMber <seri>

CALCulate<chn>:CONVert:TEST? <res>|<volt>

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Command

Description

Refer To

CALibrate:AUTO

Executes the automatic calibration procedure when using Section 8.4.5

fast measurement mode.

CALibrate<chn>:DATE:CALibrate? [MIN|MAX|DEF]

Returns the channel calibration date for the specified

channel

Section 8.4.5

CALibrate<chn>:DATE:CALibrate

Sets the channel calibration date for the specified channel Section 8.4.5

(<year>,<month>,<day>)|MIN|MAX|DEF

CALibrate<chn>:DATE:DUE? [MIN|MAX|DEF]

Returns the recalibration date for the specified channel

Sets the recalibration date for the specified channel

Section 8.4.5

CALibrate<chn>:DATE:DUE

(<year>,<month>,<day>)|MIN|MAX|DEF

CALibrate<chn>:PARameter:LINearity<n>?

[MIN|MAX|DEF]

Returns the calibration linearity parameter for the specified Section 8.4.5

channel

CALibrate<chn>:PARameter:LINearity<n>

<num>|MIN|MAX|DEF

Sets the calibration linearity parameter for the specified

channel

Section 8.4.5

CALibrate<chn>:PARameter:OFFSet<n>? [MIN|MAX|DEF] Returns the calibration offset parameter for the specified

channel

CALibrate<chn>:PARameter:OFFSet<n>

<num>|MIN|MAX|DEF

Sets the calibration offset parameter for the specified

channel

CALibrate<chn>:PARameter:RJC? [MIN|MAX|DEF]

Returns the calibration RJC offset for the specified

channel

CALibrate<chn>:PARameter:RJC <num>|MIN|MAX|DEF

Sets the calibration RJC offset for the specified channel

Section 8.4.5

CALibrate<chn>:PARameter:SCALe<n>? [MIN|MAX|DEF] Returns the calibration scale parameter for the specified

channel

CALibrate<chn>:PARameter:SCALe<n>

<num>|MIN|MAX|DEF

Sets the calibration scale parameter for the specified

channel

Section 8.4.5

DISPlay:DATE:FORMat? [MIN|MAX|DEF]

DISPlay:DATE:FORMat <num> |MIN|MAX|DEF

DISPlay:DECimal:FORMat? [MIN|MAX|DEF]

DISPlay:DECimal:FORMat <num> |MIN|MAX|DEF

DISPlay:LAMP? [MIN|MAX|DEF]

Returns a number indicating the date format

Sets the date format

Section 8.4.10

Section 8.4.6

Section 8.4.10

Section 8.4.6

Returns the decimal format

Sets the decimal format

Returns the lamp brightness

Sets the lamp brightness

Returns the display resolution

Sets the display resolution

Returns the time format

Sets the time format

DISPlay:LAMP <bool>|<num>|MIN|MAX|DEF

DISPlay:RESolution? [MIN|MAX|DEF]

DISPlay:RESolution <num> |AUT|MIN|MAX|DEF

DISPlay:TIME:FORMat? [MIN|MAX|DEF]

DISPlay:TIME:FORMat <num> |MIN|MAX|DEF

DISPlay:WINDow? [MIN|MAX|DEF]

Returns the display set

DISPlay:WINDow <num>|MIN|MAX|DEF

DISPlay:WINDow<n>:FIELd<n>:FEED?

Sets the display set

Returns the value of a specified field for a specified display Section 8.4.6

set

DISPlay:WINDow<n>:FIELd<n>:FEED <chn>[,<num>]

FETCh? [<chn>]

Sets the value of a specified field for a specified display

set

Section 8.4.6

Returns the most recent measurement for specified

channel

Section 8.4.1

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Interface Commands

Command

Description

Refer To

FORMat:STAMp?

FORMat:STAMp <bool>

Returns the extended measurement data format setting

Section 8.4.1

Enables extended measurement data format with the

FETCh?, MEASure?, and READ? commands

INITiate

Provided for compatibility but has no effect

Returns the number of entries to auto log

Sets the number of entries to auto log

Deletes auto log entries

Section 8.4.2

Section 8.4.7

Section 8.4.1

INITiate:CONTinuous?

LOGging:AUTomatic:COUNt? [MIN|MAX|DEF]

LOGging:AUTomatic:COUNt <num> |MIN|MAX|DEF

LOGging:AUTomatic:DELete [<num>|ALL]

LOGging:AUTomatic:FREE?

Returns the number of log entries free and stored

Returns the current auto log label number

Sets the current auto log label number

Returns the number of auto log entries

Prints stored auto log data

LOGging:AUTomatic:LABel? [MIN|MAX|DEF]

LOGging:AUTomatic:LABel <num> |MIN|MAX|DEF

LOGging:AUTomatic:POINt? [MAX]

LOGging:AUTomatic:PRINt [<num>|ALL [,port]]

LOGging:AUTomatic:STATus?

Returns the auto log status

LOGging:AUTomatic:STATus <bool>

LOGging:AUTomatic:TIMe? [MIN|MAX|DEF]

LOGging:AUTomatic:TIMe <num> |MIN|MAX|DEF

LOGging:AUTomatic:VALue? <num> |MIN|MAX|DEF

LOGging:DEMand:DELete [<num>|ALL]

LOGging:DEMand:FREE?

Sets the auto log state

Returns the auto log interval setting

Sets the auto log interval setting

Returns an auto log reading

Deletes demand log entries

Returns the number of log entries free and stored

Returns the current demand log label number

Sets the current demand log label number

Returns the number of demand log entries

Prints the demand log data

LOGging:DEMand:LABel? [MIN|MAX|DEF]

LOGging:DEMand:LABel <num> |MIN|MAX|DEF

LOGging:DEMand:POINt? [MAX]

LOGging:DEMand:PRINt [<num>|ALL [,<port>]]

LOGging:DEMand:STORe

Stores the current measurement into the demand log

Returns a demand log entry

LOGging:DEMand:VALue? <num> |MIN|MAX|DEF

LOGging:LABel<n>:NAME?

Returns the name of the specified label

Sets the name of the specified label

LOGging:LABel<n>:NAME <label>

MEASure? [<chn>]

Returns the most recent measurement on the specified

channel

READ? [<chn>]

Returns the most recent measurement on the specified

channel

Section 8.4.1

ROUTe:CLOSe? <chn>

ROUTe:CLOSe <chn>

ROUTe:OPEN? <chn>

ROUTe:OPEN <chn>

ROUTe:PRIMary?

Returns the state of the specified channel

Enables the specified channel

Section 8.4.3

Returns the state of the specified channel

Disables the specified channel

Returns the number of the primary channel

Returns the list of enabled channels

ROUTe:SCAN?

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Command

Description

Refer To

ROUTe:SCAN [<chn list>]

Sets the input channels for scanning

Returns the current scan mode

Sets the scan mode

Section 8.4.3

Section 8.4.2

Section 8.4.1

Section 8.4.2

ROUTe:SCAN:MODE? [MIN|MAX|DEF]

ROUTe:SCAN:MODE <num>|MIN|MAX|DEF

SENSe:AVERage:COUNt? [MIN|MAX|DEF]

SENSe:AVERage:COUNt <num> |MIN|MAX|DEF

SENSe<chn>:DATA?

Returns the moving average filter setting

Sets the moving average filter setting

Returns the input value for the specified channel

SENSe<chn>:RESistance:RANGe? [MIN|MAX|DEF]

Returns the resistance range setting for the specified

channel

SENSe,<chn>:RESistance:RANGe <num> |MIN|MAX|DEF Sets the resistance range setting for the specified channel Section 8.4.2

SENSe<chn>:RESistance:WIRE? [MIN|MAX|DEF]

SENSe<chn>:RESistance:WIRE <num> |MIN|MAX|DEF

STATus:MEASure?

Returns the probe wire setting for the specified channel

Sets the probe wire setting for the specified channel

Reads and clears the Measurement Status Register

Returns the Measurement Status Condition Register

Returns the Measurement Status Enable Register

Sets the Measurement Status Enable Register

Reads and clears the Operation Status Register

Returns the Operation Status Condition Register

Returns the Operation Status Enable Register

Sets the Operation Status Enable Register

Reads and clears the Questionable Status Register

Returns the Questionable Status Condition Register

Returns the Questionable Status Enable Register

Sets the Questionable Status Enable Register

Returns the boot ROM version

Section 8.4.2

Section 8.4.12

Section 8.4.8

Section 8.4.9

STATus:MEASure:CONDition?

STATus:MEASure:ENABle?

STATus:MEASure:ENABle <num>

STATus:OPERation?

STATus:OPERation:CONDition?

STATus:OPERation:ENABle? [MIN|MAX|DEF]

STATus:OPERation:ENABle <num> |MIN|MAX|DEF

STATus:QUEStionable?

STATus:QUEStionable:CONDition?

STATus:QUEStionable:ENABle? [MIN|MAX|DEF]

STATus:QUEStionable:ENABle <num> |MIN|MAX|DEF

SYSTem:BOOT:VERSion?

SYSTem:CODE:VERSion?

Returns the firmware code version

SYSTem:COMMunicate:IR:FEED? [MIN|MAX|DEF]

SYSTem:COMMunicate:IR:FEED <bool>|MIN|MAX|DEF

SYSTem:COMMunicate:IR:MODE? [MIN|MAX|DEF]

Returns the state of the IR port printing

Sets the state of the IR port printing

Returns the IR mode setting

SYSTem:COMMunicate:IR:MODE <num>|MIN|MAX|DEF Sets the IR mode setting

SYSTem:COMMunicate:IR:TIMe? [MIN|MAX|DEF]

SYSTem:COMMunicate:IR:TIMe <num>|MIN|MAX|DEF

SYSTem:COMMunicate:SERial:BAUD? [MIN|MAX|DEF]

Returns the IR sample period setting

Sets the IR sample period setting

Returns the serial port baud rate setting

Sets the serial port baud rate setting

SYSTem:COMMunicate:SERial:BAUD

<baud>|MIN|MAX|DEF

SYSTem:COMMunicate:SERial:FDUPlex? [MIN|MAX|DEF] Returns the serial port echo (duplex) setting

Section 8.4.9

SYSTem:COMMunicate:SERial:FDUPlex

<bool>|MIN|MAX|DEF

Sets the serial port echo (duplex) setting

SYSTem:COMMunicate:SERial:FEED? [MIN|MAX|DEF]

Returns the state of the serial port printing setting

Section 8.4.9

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Interface Commands

Command

Description

Refer To

SYSTem:COMMunicate:SERial:FEED

<bool>|MIN|MAX|DEF

Sets the state of the serial port printing setting

Returns the state of the serial port linefeed setting

Sets the state of the serial port linefeed setting

Section 8.4.9

SYSTem:COMMunicate:SERial:LINefeed?

[MIN|MAX|DEF]

SYSTem:COMMunicate:SERial:LINefeed

<bool>|MIN|MAX|DEF

SYSTem:COMMunicate:SERial:TIMe? [MIN|MAX|DEF]

Returns the serial port sample period setting

Sets the serial port sample period setting

Section 8.4.9

SYSTem:COMMunicate:SERial:TIMe <num>

|MIN|MAX|DEF

SYSTem:DATE? [MIN|MAX|DEF]

SYSTem:DATE (<year>,<month>,<day>)

SYSTem:ERRor?

Returns the date

Section 8.4.10

Section 8.4.8

Sets the date to the specified year, month, and day

Returns a system error message from the system error

queue

SYSTem:KLOCkout? [MIN|MAX|DEF]

SYSTem:KLOCkout <bool>|MIN|MAX|DEF

SYSTem:PASSword:CDISable

Returns the state of the keypad lockout

Enables or disables the keypad

Section 8.4.9

Section 8.4.11

Disables password-protected commands

Enables password-protected commands

Returns the current password-protection state

SYSTem:PASSword:CENable <pass>

SYSTem:PASSword:CENable:STATe?

SYSTem:PASSword:CONVersion? [MIN|MAX|DEF]

Returns the current password-protected state of the con-

version commands

SYSTem:PASSword:CONVersion <bool> |MIN|MAX|DEF Sets the password-protection state of the conversion

commands

Section 8.4.11

SYSTem:PASSword:NEW <pass>

SYSTem:POWer:BATTery?

SYSTem:POWer:SOURce?

SYSTem:SNUMber?

Sets a new password

Section 8.4.11

Section 8.4.9

Section 8.4.8

Section 8.4.10

Section 8.4.8

Section 8.4.2

Section 8.4.8

Returns the current battery charge level

Returns the source of power being used

Returns the instrument serial number

Returns the time

SYSTem:TIME?

SYSTem:TIME (<hour>,<minute>,<second>)

SYSTem:VERSion?

Sets the time to the specified hour, minute, second

Returns the SCPI version number

Returns the value of the scan sequence timer setting

Sets the scan sequence timer setting

Returns the system temperature units

Sets the system temperature units

TRIGger:TIMer? [MIN|MAX|DEF]

TRIGger:TIMer <num>|MIN|MAX|DEF

UNIT:TEMPerature?

UNIT:TEMPerature <unit>

8.3.2

Command Syntax

The 1529 accepts commands that set parameters, execute functions or respond

with requested data. These commands are in the form of strings of ASCII-en-

coded characters. As far as possible, the 1529 conforms to IEEE-488.2, 1992

and SCPI-1994. One notable exception is that compound commands are not al-

lowed as explained below.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Commands consist of a command header and, if necessary, parameter data. All

commands must be terminated with either a carriage return (ASCII 0D hex or

13 decimal) or new line character (ASCII 0A hex or 10 decimal).

Command headers consist of one or more mnemonics separated by colons (:).

Mnemonics may use letter characters, the underscore character (_), and possi-

bly numeric digits as well. Commands are not case sensitive. Mnemonics often

have alternate forms. Most mnemonics have a long form that is more readable

and a short form consisting of three or four characters that is more efficient.

A mnemonic may end with a numeric suffix that specifies one of a set of inde-

pendent function blocks such as input channel data paths. If a numeric suffix is

omitted when a particular block must be specified, an error is generated

(“Header suffix out of range”).

Query commands are commands that request data in response. Query com-

mands have a question mark (?) immediately following the command header.

Responses to query commands are generated immediately and placed in the

output buffer. Responses are then transmitted automatically over the RS-232 or

IR ports. When using the IEEE-488 interface, responses remain in the output

buffer until read or until another command is received or the power is turned

off. Responses are lost if not read before the next command is received. Each

input buffer holds 128 characters and each output buffer holds 256 characters.

Some commands require parameter data to specify values for one or more pa-

rameters. The command header is separated from the parameter data by a space

(ASCII 20 hex or 32 decimal). Multiple parameters are separated by a comma

(,).

The 1529 does not allow compound commands (multiple commands per line

separated with semicolons). All commands are sequential. The execution of

each command is completed before subsequent commands are processed.

8.4

Commands

Table 3, Alphabetical List of Commands in Section 8.3.1, lists the commands

in alphabetical order. In this section the commands are arranged into the fol-

lowing groups:

Measurement Commands – commands for reading measurement data.

Measurement Control Commands – commands for the timing and action of

the measurement process.

Channel Commands – commands for selecting channels.

Probe Commands – commands for temperature conversion and probe

characterization.

Calibration Coefficient Commands – commands for channel calibration

coefficients.

Display Commands – commands for display options and settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

Logging Commands – commands for automatic and demand logging.

System Commands – commands for general system configuration parameters.

Communication Interface Commands – commands for controlling the inter-

face configuration(serial port, IR, and IEEE).

Date and Time Commands – commands for setting the date, time and the date

and time formats.

Password Commands – commands for enabling and disabling the password,

for setting the password, and for checking the state of the password.

Status Commands – commands to report the status and condition of the

instrument.

Each section provides the command structure (long and short format), a de-

scription of the command purpose, a command example, an example of what

the command returns (as applicable to query commands), and notes specific to

the command. The following apply to each group of commands.

• Numeric data, specified by the mnemonic, <num>, uses ASCII characters

to represent numbers. Numbers may contain a plus or minus (‘+’ or ‘-’)

sign, decimal point (‘.’), and exponent (‘E’ or ‘e’) with its sign. If a frac-

tional component is received when only an integer is required, the number

is rounded to the nearest integer without any resulting error message. The

mnemonics DEF, MIN, and MAX are often acceptable for the default,

minimum, and maximum value respectively. Unit suffixes, such as V or

OHM, can be appended to numeric parameters and are accepted without

error but ignored.

• Unrecognized commands or commands with incorrect syntax or invalid

parameters generate error messages in the error queue.

• Upper case letters designate syntax that is required when issuing the com-

mand. Lower case letters are optional and may be omitted.

• <> indicates a required parameter.

• [] indicates optional parameters.

• () indicates a group of parameters that must be used together.

• For query commands, specifying the MIN, MAX, or DEF parameter

causes the instrument to respond with the minimum, maximum, or default

setting respectively.

• For set commands, specifying the MIN, MAX, or DEF parameters causes

the instrument to use the minimum, maximum, or default setting respec-

tively.

• ‘|’ indicates alternate parameter values.

• <chn> indicates a channel number is required.

• <dest chn> indicates a destination channel is required.

• <n> indicates a number is required.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

• <num> indicates numeric value is required.

• <chn list> indicates a list of channel numbers is required.

• <bool> indicates a Boolean value (0 or 1) is required. The mneumonics

OFF and ON are also accepted for 0 and 1, respectively.

• <conv> indicates a conversion mnemoic is required.

• <param> indicates a parameter name is required.

• <seri> indicates a serial number is required.

• <res> indicates a resistance value is required.

• <volt> indicates a voltage value is required.

• <unit> indicates a temperature unit is required.

• <pass> indicates a password is required.

• <port> indicates a port number is required.

• <label> indicates an eight character label is required.

• <year> indicates a four digit number is required.

• <month> indicates a one or two digit number is required.

• <day> indicates a one or two digit number is required.

• <hour> indicates a one or two digit number is required.

• <minute> indicates a one or two digit number is required.

• <second> indicates a one or two digit number is required.

• <baud> indicates a valid baud number is required.

8.4.1

Measurement Commands

The measurement commands are used to read information on the statistical cal-

culations and for reading the most recent measurement for a specified channel.

The measurement commands are not password protected.

8.4.1.1

CALCulate:AVERage:CLEar

Clears the statistical functions for all channels.

CALC:AVER:CLE

The *RST command clears the statistical functions.

8.4.1.2

CALCulate<chn>:AVERage<n>:DATA?

Returns the value of a statistical calculation for a given channel.

CALC3:AVER1:DATA?

0.017

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

The CALCulate suffix, <chn>, specifies the channel (1 to 4). The AVERage

suffix, <n>, specifies the calculation type. See Table 4 on page 126 for the Sta-

tistical Calculation Types.

8.4.1.3

8.4.1.4

CALCulate:AVERage<n>:TYPE?

Returns the keyword for the specified field type number.

CALC:AVER2:TYPE

STD

The AVERage suffix, <n>, specifies the calculation type number. See Table 4

on page 126 for the Statistical Calculation Types.

FETCh? [<chn>]

Returns the most recent measurement for the specified channel.

FETC? 1

0.0000011

1,2,0.0011,mV,14,5,35,2000,9,5

The <chn> parameter specifies the channel (1 to 4). If the <chn> parameter is

omitted, the most recent measurement is returned regardless of the channel. If

simultaneous sampling is on, the measurement from the lowest enabled channel

number is returned. This command does not affect the measurement action.

If the extended format setting is OFF (see Section 9.4.1.5, FORMat:STAMp

<bool>) the response is only the measurement value in units of temperature,

volts, or ohms depending on the selected probe type or temperature unit. With

this format kohms and millivolts are converted to ohms and volts respectively.

If the extended format setting is ON the measurement is returned in a

comma-delimited format as follows.

Measure status (0 if the measurement has been read previously or 1 if this is a

new measurement,

channel number,

measurement value,

scale,

hour,

minute,

seconds,

year,

month,

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

day the measurement was made

With this format kohms and millivolts are not converted to ohms and volts.

This command may return the same reading if a new reading has not yet been

obtained. If only new readings are desired, the FORMat:STAMp command can

be used to enable the extended format option and any readings in which the

value of the first field is 0 can be ignored or else the STATus:MEASure? com-

mand can be used to determine if a new reading is available for a desired

channel.

8.4.1.5

FORMat:STAMp?

Returns the extended measurement data format setting. See Section 9.4.1.4,

FETCh? for details.

FORM:STAM?

8.4.1.6

8.4.1.7

FORMat:STAMp <bool>

Enables extended measurement data format with the FETCh?, MEASure? And

READ? commands. On power up this is always set to off.

FORM:STAM ON

MEASure? [<chn>]

Returns the most recent measurement for the specified channel.

MEAS? 1

0.0127

This command is the same as the FETCh? [<chn>] command

8.4.1.8

8.4.1.9

READ? [<chn>]

Returns the most recent measurement for the specified channel.

READ? 2

0.0113

This command is the same as the ?FETCh [<chn>] command.

SENSe<chn>:DATA?

Returns the input value for the specified channel.

SENS3:DATA?

100.0291, 0.0000

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

The SENSe suffix, <chn>, specifies the channel (1 to 4). The parameter is

ohms for low range PRTs, Kohms for high range PRTs and thermistors, and

millivolts for thermocouples. The second returned parameter is always 0 for

PRTs and themistors and the reference junction temperature for thermocouples.

8.4.2

Measurement Control Commands

The measurement control commands are used to query and set the moving av-

erage filter, the resistance range, the number of probe wires, and the sequence

timer. The measurement control commands for resistance range and the number

of probe wires are password protected.

8.4.2.1

8.4.2.2

INITiate

Provided for compatibility but has no effect.

INIT

INITiate:CONTinuous?

Provided for compatibility but has no effect.

INIT:CONT?

8.4.2.3

SENSe:AVERage:COUNt? [MIN|MAX|DEF]

Returns the moving average filter setting.

SENS:AVER:COUN?

Specifying the MIN parameter returns a value of 1, specifying the MAX pa-

rameter returns a value of 10, and specifying the DEF parameter returns a value

of 1. The *RST command sets the average count to the default (1).

8.4.2.4

SENSe:AVERage:COUNt <num>|MIN|MAX|DEF

Sets the moving average filter setting.

SENS:AVER:COUN MIN

The <num> parameter must be a number between 1 and 10. Specifying the

MIN, MAX, or DEF parameter sets the moving average filter setting to the

minimum, maximum, or default, respectively. The *RST command sets the

moving average to 1.

8.4.2.5

SENSe<chn>:RESistance:RANGe? [MIN|MAX|DEF]

Returns the resistance range setting.

SENS3:RES:RANG?

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type", error

message.

The SENSE suffix, <chn>, specifies the channel (1 to 4), or memory channel (5

to 14). Specifying the MIN parameter returns a value of 0. Specifying the MAX

parameter returns a value of 1. Specifying the DEF parameter returns a value of

0. The *RST command sets the resistance range to the default (DEF).

8.4.2.6

SENSe<chn>:RESistance:RANGe <num>|MIN|MAX|DEF

Sets the resistance range setting.

SENS4:RES:RANG MIN

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type", error

message.

The SENSE suffix, <chn>, specifies the channel (1 to 4), or memory channel (5

to 14). The <num> parameter must be a number between 0 and 1. Specifying

the MIN, MAX or DEF parameter sets the resistance range setting to the mini-

mum, maximum, or default value respectively.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.2.7

SENSe<chn>:RESistance:WIRE? [MIN|MAX|DEF]

Returns the probe wire setting.

SENS1:RES:WIRE?

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type", error

message.

The SENSE suffix, <chn>, specifies the channel (1 to 4), or memory channel (5

to 14). Specifying the MIN parameter returns a value of 2. Specifying the

MAX parameter returns a value of 4. Specifying the DEF parameter returns a

value of 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.2.8

SENSe<chn>:RESistance:WIRE <num>|MIN|MAX|DEF

Sets the probe wire setting.

SENS2:RES:WIRE MIN

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type", error

message.

The SENSE suffix, <chn>, specifies the channel (1 to 4), or memory channel (5

to 14). The <num> parameter must either be 2, 3, or 4. Specifying the MIN,

MAX or DEF parameter sets the wire setting to the minimum, maximum, or

default value respectively.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.2.9

TRIGger:TIMer? [MIN|MAX|DEF]

Returns the scan sequence timer setting.

TRIG:TIM?

Specifying the MIN parameter returns a value of 0.1. Specifying the MAX pa-

rameter returns a value of 3600. Specifying the DEF parameter returns a value

of 1. The units are seconds.

8.4.2.10

TRIGger:TIMer <num>|MIN|MAX|DEF

Sets the scan sequence timer setting.

TRIG:TIM 30

The <num> parameter can be one of the following values: 0.1, 0.2, 0.5, 1, 2, 5,

10, 30, 60, 120, 300, 600, 1800 or 3600. The units are seconds. If a value other

than one listed here is used, the instrument automatically selects the nearest ac-

ceptable value that is less than the value entered. Values greater than 3600 or

less than 0.1 are ignored. Specifying the MIN, MAX, or DEF parameter sets

the scan sequence timer to the minimum, maximum, or default value respec-

tively. The *RST command sets the scan sequence timer to 1 second.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.3

Channel Commands

The channel commands are used for querying and setting the current channel,

the channels to scan, the type of scanning, and the state of the channel scan-

ning. The channel commands are not password protected.

8.4.3.1

ROUTe:CLOSe? <chn>

Returns the state of the specified channel.

ROUT:CLOS? 1

The <chn> parameter specifies the channel (1 to 4). If the specified channel is

enabled, this query returns 1. If the specified channel is disabled, this query re-

turns 0.

8.4.3.2

8.4.3.3

ROUTe:CLOSe <chn>

Enables the specified channel.

ROUT:CLOS 3

The <chn> parameter specifies the channel (1 to 4) to enable. This comand

does not apply to memory channels.

ROUTe:OPEN? <chn>

Returns the state of the specified channel.

Example: ROUT:OPEN? 1

Response: 0

The <chn> parameter specifies the channel (1 to 4). If the specified channel is

enabled this query returns 0. If the specified channel is disabled, this query re-

turns 1.

8.4.3.4

8.4.3.5

ROUTe:OPEN <chn>

Disables the specified channel.

Example: ROUT:OPEN 4

The <chn> parameter specifies the channel (1 to 4) to disable. This command

does not apply to memory channels.

ROUTe:PRIMary?

This query command returns the number of the primary channel.

Example: ROUT:PRIM?

Response: 1

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.3.6

8.4.3.7

ROUTe:SCAN?

Returns a comma delimited list of the enabled channels.

ROUT:SCAN?

(@2,3,4)

The list of channels is enclosed in parenthesis and preceded with the @

symbol.

ROUTe:SCAN <chn list>

Sets the channels for scanning.

ROUT:SCAN 2,3

The <chn list> parameter is a comma delimited list of the channels (1 to 4) to

enable. Channels that are omitted from this list are disabled. If the <chn list>

parameter is omitted, all channels are disabled. The *RST command sets chan-

nel 1 ON, and all other channels OFF.

8.4.3.8

ROUTe:SCAN:MODE? [MIN|MAX|DEF]

Returns the current scan mode setting.

ROUT:SCAN:MODE? MIN

If 0 is returned, the scan mode is simultaneous. If a 1 is returned the scan mode

is scan. Specifying the MIN parameter returns a value of 0. Specifying the

MAX parameter returns a value of 1. Specifying the DEF parameter returns a

value of 1.

8.4.3.9

ROUTe:SCAN:MODE <num>|MIN|MAX|DEF

Sets the scan mode setting.

ROUT:SCAN:MODE 1

The <num> specifies the scan mode (1 for scan, 0 for simultaneous). Spec-

ifying the MIN, MAX, or DEF parameter sets the mode to the minimum, maxi-

mum, or default, respectively. The *RST command sets scan mode to scan.

8.4.4

Probe Commands

The probe commands are used for querying, setting, and copying the probe

conversion type, conversion parameters, and serial number and for testing the

temperature conversion for a channel. The probe commands for copying and

setting parameters are password protected.

8.4.4.1

CALCulate<chn>:CONVert:CATalog?

Returns a list of conversion types available for the specified channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

CALC2:CONV:CAT?

“RES”,“ITS”,”ITS5”,”PT”,”CVD”,”TRES”,”TTEM”,”YSI”

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). Each item in the response list is enclosed in double quotes and

separated from other items by a comma. See Table 7 on page 128, for the avail-

able conversion types.

8.4.4.2

CALCulate<chn>:CONVert:COPY <dest chn>|ALL

Copies the conversion type, sub-ranges (ITS-90), serial number, and character-

ization coefficients from one channel to another.

CALC2:CONV:COPY 8

The CALCulate suffix <chn> specifies the source channel (1 to 4). The <dest

chn> parameter specifies the destination channel (1 to 4). When the copy is

performed, the source channel parameters are not affected. If the destination

channel type is different from the source channel type, the error -294, "Incom-

patible type" is generated. Specifying the ALL parameter copies the source

channel parameters to all compatible channels. The example above copies the

parameters from channel 2 to memory channel PMEM3.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.4.3

CALCulate<chn>:CONVert:NAMe?

Returns the name of the selected conversion type for the specified channel.

CALC2:CONV:NAME?

ITS

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The conversion types and their names are listed in Table 7 on

page 128.

8.4.4.4

CALCulate<chn>:CONVert:NAMe <conv>

Sets the conversion type for the specified channel.

CALC2:CONV:NAME CVD

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The <conv> parameter is a mnemonic indicating the conversion

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

type. The acceptable conversion types depend on the channel type. The conver-

sion types and their names are listed in Table 7 on page 128.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.4.5

CALCulate<chn>:CONVert:PARameter:CATalog?

Returns the names of the probe characterization parameters associated with the

current conversion type for the specified channel.

CALC2:CONV:PAR:CAT?

“RANGE”,”RTPW”,”A4”,”B4”,”A”,”B”,”C”,”D”

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). Each item in the response list is enclosed in double-quotes and

separated from other items by a comma. Each item indicates the name of a

characterization parameter for the current conversion type.If there are no pa-

rameters available for the current conversion type, an empty string is returned.

The list of parameters depends on the selected conversion type. Characteriza-

tion parameters for the various conversion types are listed in Table 8 on page

128, Conversion Types and Parameters.

8.4.4.6

CALCulate<chn>:CONVert:PARameter:VALue? [<param>|ALL]

Returns the value of the specified conversion parameter for the specified

channel.

CALC2:CONV:PAR:VAL? RTPW

100.0145

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The <param> parameter is the name of the parameter as given in

Table 8, Conversion Types and Parameters. If the <param> parameter does not

apply to the selected conversion type, an error -221, “Settings Conflict”, is

generated. Specifying the ALL parameter returns the name and value of all pa-

rameters associated with the specified channel in a comma delimited list. If no

parameter is specified, the ALL parameter is assumed. The format of the re-

sponse consists of a parameter name, enclosed in double quotes, followed by its

value (i.e. "param1",value1,"param2",value2,"param3",value3,...).

8.4.4.7

CALCulate<chn>:CONVert:PARameter:VALue <param>,<num>[,<

param>,<num>...]

Sets the value of one or more conversion parameters for the specified channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

CALC2:CONV:PAR:VAL RTPW, 100.0145, A4, 0.0045

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The <param> parameter is the name of the parameter as given in

Table 8, Conversion Types and Parameters. If the <param> parameter is not ap-

plicable to the current conversion type, an error -221, “Settings Conflict”, is

generated. The <num> parameter is the desired value of the parameter. Multiple

parameters can be set using a single command by separating the <param> and

<num> prameters by commas. The order of the parameters is not important but

the value must immediately follow the parameter name.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.4.8

CALCulate:CONVert:PRINt [<chn>|ALL [,<port>]]

Prints the conversion parameters for the specified channel.

CALC:CONV:PRIN 2

“PRB”,CHAN2,”ser”,090105,”TYP”,RES,”RANGE”,0

If no parameters are specified, the ALL parameter is assumed and the parame-

ters for all channels are printed to the current port. Specifying the <chn> pa-

rameter prints only the parameters for the specified channel (1 to 4) to the

current port. Optionally, the parameters may be printed to a specific port by

specifying the <port> parameter (see Table 10 on page 129, Port Numbers)

8.4.4.9

CALCulate<chn>:CONVert:SNUMber?

Returns the probe serial number for the specified channel.

CALC2:CONV:SNUM?

A_336C

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The returned serial number is in string format.

8.4.4.10

CALCulate<chn>:CONVert:SNUMber <serl>

Sets the probe serial number for the specified channel.

CALC2:CONV:SNUM A_336C

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). The <serl> parameter is in string format. The <serl> parameter

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

can consist of up to eight characters that include any letters, numeric digits, and

the underscore ‘_’.

This command may be password-protected. To access this command:

• If the SYST:PASS:CONV? command returns a 0 (probe password-protec-

tion is disabled), the password is not required.

• If the SYST:PASS:CONV? command returns a 1 (probe password-protec-

tion is enabled), the password must be successfully entered using the

SYST:PASS:CEN <pass> command (see Section 9.4.11, Password Com-

mands).

8.4.4.11

CALCulate<chn>:CONVert:TEST? <res>|<volt>

Tests the temperature conversion for the specified channel.

CALC2:CONV:TEST? 100.0145

0.0100

The CALCulate suffix, <chn>, specifies the channel (1 to 4) or memory chan-

nel (5 to 14). For PRT/Thermistor channels, the <res> parameter specifies a re-

sistance value to convert to temperature. The <res> parameter is always in

Ohms for PRTs and KOhms for Thermistors. For Thermocouple channels, the

<volt> parameter specifies a voltage value to convert to temperature. The

<volt> parameter is always in mV. The response to this command is a tempera-

ture in the currently selected units. The current system units determine the scale

of the response.

8.4.5

Calibration Coefficient Commands

The calibration coefficient commands are used for querying and setting the

channel calibration date, due date, linearity, offset, scale, and RJC.

8.4.5.1

CALibrate:AUTo

Executes the automatic calibration procedure when using Fast Measurement

Mode (see Sections 6.9, Fast Measurement Mode, 7.1.1, Measure Period and

Fast Measurement Mode, and 7.1.5, Display Functions/Auto-Cal).

CAL:AUT

8.4.5.2

CALibrate<chn>:DATE:CALibrate? [MIN|MAX|DEF]

Returns the calibration date for the specified channel.

CAL1:DATE:CAL?

2000,9,22

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. The response is returned in the format,

<year>,<month>,<day>. Specifying the MIN parameter returns a value of

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

2000,1,1. Specifying the MAX parameter returns a value of 2099,12,31. Spec-

ifying the DEF parameter returns a value of 2000,1,1.

8.4.5.3

CALibrate<chn>:DATE:CALibrate

(<year>,<month>,<day>)|MIN|MAX|DEF

Sets the calibration date for the specified channel.

CAL1:DATE:CAL 2000,8,29

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. The <year>, <month>, and <day> parame-

ters must all be supplied. The <year> parameter is a four-digit number (2000 to

2099). The <month> parameter is a one or two-digit number (1 to 12). The

<day> parameter is a one or two-digit number (1 to 31). Specifying the MIN,

MAX or DEF parameter sets the calibration date to the minimum, maximum,

or default value respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <pass> command

(see Section 8.4.11, Password Commands).

8.4.5.4

CALibrate<chn>:DATE:DUE? [MIN|MAX|DEF]

Returns the recalibration date for the specified channel.

CAL1:DATE:DUE?

2001,9,21

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. The response is returned in the format,

<year>,<month>,<day>. Specifying the MIN parameter returns a value of

2000,1,1. Specifying the MAX parameter returns a value of 2099,12,31. Spec-

ifying the DEF parameter returns a value of 2000,1,1.

8.4.5.5

CALibrate<chn>:DATE:DUE (<year>,<month>,<day>)|MIN|MAX|DEF

Sets the recalibration date for the specified channel.

CAL1:DATE:DUE 2001,8,28

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. The <year>, <month>, and <day> parame-

ters must all be supplied. The <year> parameter is a four-digit number (2000 to

2099). The <month> parameter is a one or two-digit number (1 to 12). The

<day> parameter is a one or two-digit number (1 to 31). Specifying the MIN,

MAX or DEF parameter sets the recalibration date to the minimum, maximum,

or default value respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <pass> command

(see Section 9.4.11, Password Commands).

100

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.5.6

CALibrate<chn>:PARameter:OFFSet<n>? [MIN|MAX|DEF]

Returns the calibration offset parameter for the specified channel.

CAL1:PAR:OFFS2?

–1.2

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion offset suffix <n> specifies the resistance range parameter for PRTs (1) or

Thermistors (2). For Thermocouple channels, the calibration offset suffix <n>

is ignored and may be omitted. Note: For PRT/Thermistor channels, the value

returned by this command is always in ohms.

For PRT/Thermistor channels, specifying the MIN parameter returns a value of

-9 when the offset suffix <n> is 1 (for PRTs) and -9000 when the offset suffix

<n> is 2 (for Thermistors). For Thermocouple channels, specifying the MIN

parameter returns a value of -9. For PRT/Thermistor channels, specifying the

MAX parameter returns a value of 9 when the offset suffix <n> is 1 (for PRTs)

and 9000 when the offset suffix <n> is 2 (for Thermistors). For Thermocouple

channels, specifying the MAX parameter returns a value of 9. Specifying the

DEF parameter returns a value of 0.

8.4.5.7

CALibrate<chn>:PARameter:OFFSet<n> <num>|MIN|MAX|DEF

Sets the calibration offset parameter for the specified channel.

CAL1:PAR:OFFS2 5

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion offset suffix <n> specifies the resistance range parameter (in ohms) for

PRTs (1) or Thermistors (2). For Thermocouple channels, the calibration offset

suffix <n> is ignored and may be omitted. The <num> paramter specifies the

value for the specified offset parameter. Specifying the MIN, MAX or DEF pa-

rameter sets the offset parameter to the minimum, maximum, or default value

respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <password> com-

mand (see Section 9.4.11, Password Commands).

8.4.5.8

CALibrate<chn>:PARameter:SCALe<n>? [MIN|MAX|DEF]

Returns the calibration scale parameter for the specified channel.

CAL1:PAR:SCAL2?

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion scale suffix <n> specifies the resistance range parameter for PRTs (1) or

101

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Thermistors (2). For Thermocouple channels, the calibration scale suffix <n> is

ignored and may be omitted. Note: For PRT/Thermistor channels, the value re-

turned by this command is always in ohms.

For PRT/Thermistor channels, specifying the MIN parameter returns a value of

-9 when the scale suffix <n> is 1 (for PRTs) and -9000 when the scale suffix

<n> is 2 (for Thermistors). For Thermocouple channels, specifying the MIN

parameter returns a value of -9. For PRT/Thermistor channels, specifying the

MAX parameter returns a value of 9 when the scale suffix <n> is 1 (for PRTs)

and 9000 when the scale suffix <n> is 2 (for Thermistors). For Thermocouple

channels, specifying the MAX parameter returns a value of 9. Specifying the

DEF parameter returns a value of 0.

8.4.5.9

CALibrate<chn>:PARameter:SCALe<n> <num>|MIN|MAX|DEF

Sets the calibration scale parameter for the specified channel.

CAL1:PAR:SCAL2 2

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion scale suffix <n> specifies the resistance range parameter (in ohms) for

PRTs (1) or Thermistors (2). For Thermocouple channels, the calibration scale

suffix <n> is ignored and may be omitted. The <num> parameter specifies the

value for the specified scale parameter. Specifying the MIN, MAX, or DEF pa-

rameter sets the scale parameter to the minimum, maximum, or default value

respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <pass> command

(see Section 9.4.11, Password Commands).

8.4.5.10

CALibrate<chn>:PARameter:LINearity<n>? [MIN|MAX|DEF]

Returns the calibration linearity parameter for the specified channel.

CAL1:PAR:LIN1?

2.8

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type" error

message.

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion linearity suffix, <n>, specifies the resistance range parameter for PRTs (1)

or Thermistors (2). Note: For PRT/Thermistor channels, the value returned by

this command is always in ohms.

Specifying the MIN parameter returns a value of -9 when the linearity suffix

<n> is 1 (for PRTs) and -9000 when the linearity suffix <n> is 2 (for Thermis-

tors). Specifying the MAX parameter returns a value of 9 when the linearity

102

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

suffix <n> is 1 (for PRTs) and 9000 when the linearity suffix <n> is 2 (for

Thermistors). Specifying the DEF parameter returns a value of 0.

8.4.5.11

CALibrate<chn>: PARameter:LINearity<n> <num>|MIN|MAX|DEF

Sets the calibration linearity parameter for the specified channel.

CAL1:PAR:LIN1 5

This command only applies to PRT/Thermistor channels. Executing this com-

mand on Thermocouple channels generates a -294, "Incompatible type" error

message.

The CALibrate suffix, <chn>, specifies the channel (1 to 4). This command

does not apply to memory channels. For PRT/Thermistor channels, the calibra-

tion scale suffix <n> specifies the resistance range parameter (in ohms) for

PRTs (1) or Thermistors (2). The <num> parameter specifies the value for the

specified linearity parameter. Specifying the MIN, MAX, or DEF parameter

sets the linearity parameter to the minimum, maximum, or default value

respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <password> com-

mand (see Section 9.4.11, Password Commands).

8.4.5.12

CALibrate<chn>:PARameter:RJC? [MIN|MAX|DEF]

Returns the calibration RJC offset parmeter for the specified channel.

CAL1:PAR:RJC?

2.1

This command only applies to Thermocouple channels. Executing this com-

mand on PRT/Thermistor channels generates a -294, "Incompatible type" error

message.

The RJC suffix, <chn>, specifies the channel (1 to 4). This command does not

apply to memory channels. Specifying the MIN parameter returns a value of

–9. Specifying the MAX parameter returns a value of 9. Specifying the DEF

parameter returns a value of 0.

8.4.5.13

CALibrate<chn>:PARameter:RJC <num>|MIN|MAX|DEF

Sets the calibration RJC offset parameter for the specified channel.

CAL3:PAR:RJC 1.6

This command only applies to Thermocouple channels. Executing this com-

mand on PRT/Thermistor channels generates a -294, "Incompatible type" error

message.

The RJC suffix, <chn>, specifies the channel (1 to 4). This command does not

apply to memory channels. The <num> parameter specifies the RJC value for

103

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

the specified channel. Specifying the MIN, MAX, or DEF parameter sets the

RJC parameter to the minimum, maximum, or default value respectively.

This command is password-protected. To access this command, the password

must be successfully entered using the SYST:PASS:CEN <pass> command

(see Section 9.4.11, Password Commands).

8.4.6

Display Commands

The display commands are used for querying and setting the display resolution,

lamp brightness, decimal format, window setting, and window fields.

8.4.6.1

DISPlay:RESolution? [MIN|MAX|DEF]

Returns the display resolution setting.

DISP:RES?

Specifying the MIN pamameter returns a value of 0. Specifying the MAX pa-

rameter returns a value of 4. Specifying the DEF parameter returns AUT.

8.4.6.2

DISPlay:RESolution <num>|AUT|MIN|MAX|DEF

Sets the display resolution setting.

DISP:RES 3

The <num> parameter specifies the number of decimal places to display. This

parameter can be 0, 1, 2, 3, or 4. Specifying the MIN, MAX or DEF parameter

sets the display resolution to the minimum, maximum, or default value respec-

tively. Specifying the AUT parameter sets the display resolution to automatic.

8.4.6.3

8.4.6.4

DISPlay:LAMP? [MIN|MAX|DEF]

Returns the lamp brightness setting.

DISP:LAMP?

Specifying the MIN parameter returns a value of 0. Specifying the MAX pa-

rameter returns a value of 3. Specifying the DEF parameter returns a value of 0.

DISPlay:LAMP <bool>|<num>|MIN|MAX|DEF

Sets the lamp brightness setting.

DISP:LAMP ON

The lamp can be turned on or off by using either the <bool> parameter (ON or

OFF), the <num> parameter (0, 1, 2 or 3), or the MIN, MAX or DEF parame-

ters. Specifying the <bool> parameter to ON turns on the lamp. Specifying the

104

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

MIN, MAX, or DEF sets the lamp to the minimum, maximum, or default value

respectively.

8.4.6.5

DISPlay:DECimal:FORMat? [MIN|MAX|DEF]

Returns the current decimal format setting.

DISP:DEC:FORM?

A returned value of 0 indicates a period (.) is used as the decimal separator. A

returned value of 1 indicates a comma (,) is used as the decimal separator.

Specifying the MIN parameter returns a value of 0. Specifying the MAX pa-

rameter returns a value of 1. Specifying the DEF parameter returns a value of 0.

8.4.6.6

8.4.6.7

DISPlay:DECimal:FORMat <num>|MIN|MAX|DEF

Sets the decimal format setting.

DISP:DEC:FORM 1

The <num> parameter can be either a 0 for a period (.) or a 1 for a comma (,).

Specifying the MIN, MAX or DEF parameter sets the decimal format to the

minimum, maximum, or default value respectively.

DISPlay:WINDow? [MIN|MAX|DEF]

Returns the current display set.

DISP:WIND?

Specifying the MIN parameter returns a value of 1. Specifying the MAX pa-

rameter returns a value of 9. Specifying the DEF parameter returns a value of 1.

8.4.6.8

8.4.6.9

DISPlay:WINDow <num>|MIN|MAX|DEF

Sets the current display set.

DISP:WIND MIN

The <num> parameter specifies the display set to select. Specifying MIN,

MAX, or DEF parameter sets the current display set to the minimum, maxi-

mum, or default respectively.

DISPlay:WINDow<n>:FIELd<n>:FEED?

Returns the current setting of the specified field for the specified display set.

DISP:WIND1:FIEL2:FEED?

0,16

105

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The WINDow suffix, <n>, specifies the display set (1 to 9). The FIELd suffix,

<n>, specifies the field (1 to 8) within the display set. The response consists of

two numbers separated by a comma. The first number represents the channel

associated with the field. The second number represents the parameter to be

displayed in the specified field. See Table 5 on page 126, Field Types, for the

field types.

8.4.6.10

DISPlay:WINDow<n>:FIELd<n>:FEED <chn>[,<num>]

Sets the specified field within the specified display set.

DISP:WIND1:FIEL3:FEED 0,10

The WINDow suffix, <n>, specifies the display set (1 to 9). The FIELd suffix,

<n>, specifies the field (1 to 8) within the display set. The <chn> parameter

specifies channel (1 to 4) associated with the field. The <num> parameter spec-

ifies the parameter to be displayed in the specified field. See Table 5 on page

126, Field Types, for the field types.

8.4.7

Logging Commands

The logging commands are used for logging data automatically and on demand.

8.4.7.1

LOGging:AUTomatic:DELete [<num>|ALL]

Deletes entries from the auto log.

LOG:AUT:DEL 10

Specifying a number in the <num> parameter causes all auto log entries with

that label number (1 to 25) to be deleted. If the ALL parameter is specified or

no parameter is specified, all auto log entries are deleted.

8.4.7.2

LOGging:AUTomatic:COUNt? [MIN|MAX|DEF]

Returns the number of measurements to be stored in the auto log during an auto

log session.

LOG:AUT:COUN?

5000

Specifying the MIN parameter returns a value of 1. Specifying the MAX pa-

rameter value returns a value of 8160. Specifying the DEF parameter returns a

value of 8160.

8.4.7.3

LOGging:AUTomatic:COUNt <num>|MIN|MAX|DEF

Sets the number of measurements to be stored to the auto log during an auto

log session.

LOG:AUT:COUN 100

106

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

The <num> parameter is the number of measurements to be stored in the auto

log during the auto log session. Specifying the MIN, MAX, or DEF parameter

sets the number of measurements to auto log to the minimum, maximum, or de-

fault respectively.

8.4.7.4

LOGging:AUTomatic:FREE?

Returns the number of auto log entries free and stored.

LOG:AUT:FREE?

8144,16

The response consists of two numbers separated by a comma. The first number

indicates the number of auto log entries still available. The second number indi-

cates the number of entries already stored.

Note: Every time an auto log session is started, the first entry in the log for that

session consists of the data label and the date. All subsequent entries in the auto

log for that session consist of the channel, measurement value, units, and time.

Therefore, an auto log session that stores 100 measurements actually uses 101

log entries.

8.4.7.5

LOGging:AUTomatic:LABel? [MIN|MAX|DEF]

Returns the current auto log label setting.

LOG:AUT:LAB?

Specifying the MIN parameter returns a value of 1, Specifying the MAX pa-

rameter returns a value of 25. Specifying the DEF parameter returns a value of

8.4.7.6

8.4.7.7

LOGging:AUTomatic:LABel <num>|MIN|MAX|DEF

Sets the current auto log label.

LOG:AUT:LAB 4

The <num> parameter specifies the auto log label number (1 to 25) to select.

Specifying the MIN, MAX, or DEF parameter sets the auto log label to the

minimum, maximum, or default respectively.

LOGging:AUTomatic:POINt? [MAX]

Returns the number of auto log entries already stored.

LOG:AUT:POIN?

Specifying the MAX parameter returns the total number of entries that can be

stored in the auto log.

107

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.7.8

LOGging:AUTomatic:PRINt [<num>|ALL [,<port>]]

Prints the auto log entries.

LOG:AUT:PRIN ALL

DATA_25 1 22.676C 12:19:42 09-05-00

DATA_25 2 9.960 KO 12:19:44 09-05-00

DATA_25 3 23.220C 12:19:46 09-05-00

DATA_25 4 23.245C 12:19:48 09-05-00

DATA_25 1 22.765C 12:19:52 09-05-00

DATA_25 2 9.962 KO 12:19:54 09-05-00

DATA_25 3 23.087C 12:19:56 09-05-00

DATA_25 4 23.260C 12:19:58 09-05-00...

If no parameters are specified, the ALL parameter is assumed and all auto log

entries are printed to the serial port. Specifying the <num> parameter prints

only the log entries with the specified label number to the serial port. Op-

tionally, the log entries may be printed to a specific port by specifying the

<port> parameter (see Table 10 on page 129, Port Numbers).

8.4.7.9

LOGging:AUTomatic:STATus?

Returns the auto log status.

LOG:AUT:STAT?

If this query returns a 0, an auto log session is not running. If this query returns

a 1, an auto log session is running.

8.4.7.10

8.4.7.11

LOGging:AUTomatic:STATus <bool>

Sets the auto log status.

LOG:AUT:STAT 0

The <bool> parameter turns auto logging on (1 or ON) or off (0 or OFF). If si-

multaneous scan mode is enabled, one measurement is stored for each channel

in the auto log. The *RST command set the auto log status to off.

LOGging:AUTomatic:TIMe? [MIN|MAX|DEF]

Returns the auto log interval setting.

LOG:AUT:TIM?

Specifying the MIN parameter returns a value of 0.1. Specifying the MAX pa-

rameter value returns value of 3600. Specifying the DEF parameter returns a

value of 1. The units are seconds.

108

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.7.12

LOGging:AUTomatic:TIMe <num>|MIN|MAX|DEF

Sets the auto log interval setting.

LOG:AUT:TIM 1

The <num> parameter can be one of the following values: 0.1, 0.2, 0.5, 1, 2, 5,

10, 30, 60, 120, 300, 600, 1800 or 3600. The units are seconds. If a value other

than one listed is used, the instrument automatically selects the nearest accept-

able value that is less than the value entered. Values greater than 3600 or less

than 0.1 are ignored. Specifying the MIN, MAX or DEF parameter sets the log

interval setting to the minimum, maximum, or default value respectively.

8.4.7.13

LOGging:AUTomatic:VALue? <num>|MIN|MAX|DEF

Returns the specified auto log entry.

LOG:AUT:VAL? 10

,1,22.860,C,12,19,46,,,

The <num> parameter specifies the auto log entry to return. Specifying either

the MIN or DEF parameter returns the first entry in the auto log. Specifying the

MAX parameter returns the last entry in the auto log.

Note: Every time an auto log session is started, the first entry in the log for that

session consists of the data label and the date. All subsequent entries in the auto

log for that session consist of the channel, measurement value, units and time.

Therefore, an auto log session that stores 100 measurements actually uses 101

log entries.

8.4.7.14

8.4.7.15

LOGging:DEMand:DELete [<num>|ALL]

Deletes entries from the demand log.

LOG:DEM:DEL 5

Specifying a number in the <num> parameter causes all demand log entries

with that label number (1 to 25) to be deleted. If the ALL parameter is specified

or no parameter, all demand log entries are deleted.

LOGging:DEMand:FREE?

Returns the number of demand log entries free and stored.

LOG:DEM:FREE?

87,12

The response consists of two numbers separated by a comma. The first number

indicates the number of demand log entries still available. The second number

indicates the number of entries already stored.

109

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Note: Every time a demand log reading is stored, the first entry in the log for

that stored reading is the data label and the date. All subsequent entries in the

demand log consist of the channel, measurement value, units, and time.

8.4.7.16

LOGging:DEMand:LABel? [MIN|MAX|DEF]

Returns the current demand log label setting.

LOG:DEM:LAB?

Specifying the MIN parameter returns a value of 1. Specifying the MAX pa-

rameter returns a value of 25. Specifying the DEF parameter returns a value of

8.4.7.17

8.4.7.18

LOGging:DEMand:LABel <num>|MIN|MAX|DEF

Sets the current demand log label.

LOG:DEM:LAB 3

The <num> parameter specifies the demand log label number (1 to 25) to se-

lect. Specifying the MIN, MAX, or DEF parameter sets the demand log label to

the minimum, maximum, or default respectively.

LOGging:DEMand:POINt?

Returns the number of demand log entries already stored.

LOG:DEM:POIN?

Specifying the MAX parameter returns the total number of entries that can be

stored in the demand log.

8.4.7.19

LOGging:DEMand:PRINt [<num>|ALL [,<port>]]

Prints the demand log entries.

LOG:DEM:PRIN 23,1

DATA_23 1 22.862C 14:59:43 09-05-00

DATA_23 2 9.963 KO 14:59:44 09-05-00

DATA_23 3 23.097C 14:59:45 09-05-00

DATA_23 4 23.202C 14:59:46 09-05-00

If no parameters are specified, the ALL parameter is assumed and all demand

log entries are printed to the serial port. Specifying the <num> parameter prints

only the log entries with the specified label number to the serial port. Op-

tionally, the log entries may be printed to a specific port by specifying the

<port> parameter (see Table 10 on page 129, Port Numbers).

110

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.7.20

8.4.7.21

LOGging:DEMand:STORe

Stores the current measurement into the demand log.

LOG:DEM:STOR

If simultaneous scan mode is enabled, one reading is stored in the log for each

enabled channel.

LOGging:DEMand:VALue? <num>|MIN|MAX|DEF

Returns the specified demand log entry.

LOG:DEM:VAL? 10

DATA_25,2,9.961,KO,14,59,35,2000,9,5

The <num> parameter specifies the demand log entry to return. Specifying ei-

ther the MIN or DEF parameter returns the first entry in the demand log. Spec-

ifying the MAX parameter returns the last entry in the demand log. Each entry

in the demand log consist of the label, channel number, measurement value,

scale, time and date.

8.4.7.22

8.4.7.23

LOGging:LABel<n>:NAME?

Returns the name of the specified label.

LOG:LAB18:NAME?

DATA_18

The label suffix, <n>, specifies the number of the label (1 to 25) to retrieve.

The label name is returned in string format.

LOGging:LABel<n>:NAME <label>

Sets the name of the specified label.

LOG:LAB18:NAME BATH

The label suffix, <n>, specifies the number of the label (1 to 25) to set. Label

names can be up to 8 characters in length and can include any letters, numeric

digits, and the underscore (‘_’).

8.4.8

System Commands

The system commands are used for querying instrument identification parame-

ters, temperature units, and for setting operating parameters to the defined de-

fault values.

8.4.8.1

*IDN?

Returns the instrument identification string that indicates the manufacturer,

model number, serial number, and code firmware version.

111

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

*IDN?

HART,1529,A09001,1.11

8.4.8.2

*OPT?

Returns a list of input modules installed.

*OPT?

PRT,TC

Input module types are reported by position, top to bottom, of the two input

modules. The returned example is for a 1529 equipped with one 2-channel PRT

input module and one 2-channel Thermocouple input module.

8.4.8.3

*RST

Sets the instrument operating parameters to defined conditions.

*RST

The following parameters are set when this command is issued.

• Sets the scanning sequence timer to 1 second.

• Sets channel 1 ON and all others OFF.

• Sets the scan mode to SCAN.

• Sets the moving average to 1.

• Sets the printing to all ports OFF.

• Sets the units to C.

• Sets the resolution to AUTO.

• Stops auto logging.

• Clears the statistical functions.

8.4.8.4

8.4.8.5

SYSTem:BOOT:VERSion?

Returns the boot ROM version.

SYST:BOOT:VERS?

0.50

SYSTem:CODE:VERSion?

Returns the firmware code version.

SYST:CODE:VERS?

1.11

112

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.8.6

SYSTem:ERRor?

Returns a system error message if any are present in the system error queue.

SYST:ERR?

0,“No error”

Each error condition produces only one error message at a time. The error

queue may contain up to ten messages. The messages are reported in the order

they occured. Reading a message from the queue removes the message so the

next message can be read. If more than ten errors occur before being read, the

tenth error in the queue is -350,“Queue overflow” and all but the first nine er-

rors are discarded. All errors cause the Error Bit (ERR, bit 2) for the Status

BYTE Register to be set. Refer to Troubleshooting section for the error

messages.

8.4.8.7

SYSTem:SNUMber?

Returns the instrument serial number.

SYST:SNUM?

A09002

If the serial number has not been set, a 0 is returned. The serial number is set at

the factory and cannot be changed!

8.4.8.8

8.4.8.9

SYSTem:VERSion?

Returns the SCPI version number.

SYST:VERS?

1994.0

UNIT:TEMPerature?

Returns the system temperature units.

UNIT:TEMP?

The response is either C for Celsius, F for Fahrenheit, or K for Kelvin.

8.4.8.10

UNIT:TEMPerature <unit>

Sets the system temperature units.

UNIT:TEMP C

The <unit> parameter is either C or CEL for Celsius, F or FAR for Fahrenheit,

or K or Kelvin for Kelvin. The *RST command sets the units to Celsius.

113

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.9

Communication Interface Commands

The communication interface commands are used for querying and setting se-

rial port, IR, and IEEE configuration parameters.

8.4.9.1

SYSTem:COMMunicate:IR:FEED? [MIN|MAX|DEF]

Returns the state of the IR port printing.

Example: SYST:COMM:SER:FEED?

Response: 0

A value of 1 is returned if IR port printing is enabled. A value of 0 is returned

if IR port printing is disabled. Specifying the MIN parameter returns a value of

0. Specifying the MAX parameter returns a value of 1. Specifying the DEF pa-

rameter returns a value of 0.

8.4.9.2

SYSTem:COMMunicate:IR:FEED <bool>|MIN|MAX|DEF

Sets the state of the IR port printing.

Example: SYST:COMM:SER:FEED DEF

The <bool> parameter turns IR printing on (1 or ON) or off (0 or OFF). Spec-

ifying the MIN, MAX, or DEF parameter sets the IR printing to the minimum,

maximum, or default value respectively. The *RST command sets the IR port

printing to OFF.

8.4.9.3

SYSTem:COMMunicate:IR:MODE? [MIN|MAX|DEF]

Returns the IR mode setting.

Example: SYST:COMM:IR:MODE?

Response: 0

A value of 0 is returned if the IR mode is off (IR port is disabled). A value of 1

is returned if the IR port is in HP printer mode. A value of 2 is returned if the

IR port is in communications mode. This mode should be used when using the

thermometer readout with the LogWare software. A value of 3 is returned if the

IR port is in IRDA mode. Specifying the MIN parameter returns a value of 0.

Specifying the MAX parameter returns a value of 2. Specifying the DEF pa-

rameter returns a value of 0.

8.4.9.4

SYSTem:COMMunicate:IR:MODE <num>|MIN|MAX|DEF

Sets the IR mode setting.

Example: SYST:COMM:IR:MODE 1

The <num> parameter specifies the IR mode setting. A value of 0 turns IR

mode off (IR port is disabled). A value of 1 sets the IR mode to HP printer

mode. A value of 2 sets the IR mode to communications mode. A value of 3

114

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

sets the IR mode to IRDA mode. Specifying the MIN, MAX, or DEF parameter

sets the IR mode to the minimum, maximum, or default value respectively.

8.4.9.5

SYSTem:COMMunicate:IR:TIMe? [MIN|MAX|DEF]

Returns the IR sample period setting.

Example: SYST:COMM:IR:TIM?

Response: 1

Specifying the MIN parameter returns a value of 0.1. Specifying the MAX pa-

rameter returns a value of 3600. Specifying the DEF parameter returns a value

of 1.

8.4.9.6

SYSTem:COMMunicate:IR:TIMe <num>|MIN|MAX|DEF

Sets the IR port sample period setting.

Example: SYST:COMM:IR:TIMe 1

The <num> parameter can be one of the following values: 0.1, 0.2, 0.5, 1, 2, 5,

10, 30, 60, 120, 300, 600, 1800 or 3600. The units are seconds. If a value other

than one listed here is used, the instrument automatically selects the nearest ac-

ceptable value that is less than the value entered. Values greater than 3600 or

less than 0.1 are ignored. Specifying the MIN, MAX or DEF parameter sets the

sample period setting to the minimum, maximum, or default value respectively.

8.4.9.7

SYSTem:COMMunicate:SERial:BAUD? [MIN|MAX|DEF]

Returns the serial port baud rate setting.

SYST:COMM:SER:BAUD?

2400

Specifying the MIN parameter returns a value of 1200. Specifying the MAX

parameter returns a baud rate of 19200. Specifying the DEF parameter returns a

baud rate of 9600.

8.4.9.8

SYSTem:COMMunicate:SERial:BAUD <baud>|MIN|MAX|DEF

Sets the serial port baud rate setting.

SYST:COMM:SER:BAUD MIN

The <baud> parameter can be one of the following values: 1200, 2400, 4800,

9600, or 19200. If a value other than one listed is used, the instrument automat-

ically selects the nearest acceptable value. Values greater than 19200 or less

than 1200 are ignored. Specifying the MIN, MAX or DEF parameter sets the

port baud rate setting to the minimum, maximum, or default value respectively.

8.4.9.9

SYSTem:COMMunicate:SERial:FDUPlex? [MIN|MAX|DEF]

Returns the serial port echo (duplex) setting.

115

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

SYST:COMM:SER:FDUP?

A value of 1 is returned if serial port echo (duplex) is ON. A value of 0 is re-

turned if serial port echo (duplex) is OFF. Specifying the MIN parameter re-

turns a value of 0. Specifying the MAX parameter returns a value of 1.

Specifying the DEF parameter returns a value of 1.

8.4.9.10

8.4.9.11

SYSTem:COMMunicate:SERial:FDUPlex <bool>|MIN|MAX|DEF

Sets the serial port echo (duplex) setting.

SYST:COMM:SER:FDUP MAX

The <bool> parameter turns serial port echo (duplex) mode on (1 or ON) or off

(0 or OFF). Specifying the MIN, MAX, or DEF parameter sets the serial port

echo (duplex) to the minimum, maximum, or default respectively.

SYSTem:COMMunicate:SERial:FEED? [MIN|MAX|DEF]

Returns the state of the serial port printing.

SYST:COMM:SER:FEED?

A value of 1 is returned if serial port printing is enabled. A value of 0 if re-

turned is serial port printing is disabled. Specifying the MIN parameter returns

a value of 0. Specifying the MAX parameter returns a value of 1. Specifying

the DEF parameter returns a value of 0.

8.4.9.12

SYSTem:COMMunicate:SERial:FEED <bool>|MIN|MAX|DEF

Sets the state of the serial port printing.

SYST:COMM:SER:FEED DEF

The <bool> parameter turns serial printing on (1 or ON) or off (0 or OFF).

Specifying the MIN, MAX, or DEF parameter sets the serial port printing value

to the minimum, maximum, or default respectively. The *RST command sets

the serial port printing to OFF.

8.4.9.13

SYSTem:COMMunicate:SERial:LINefeed? [MIN|MAX|DEF]

Returns the state of the serial port linefeed setting.

SYST:COMM:SER:LIN?

A value of 1 is returned if linefeed is enabled. A value of 0 is returned if line-

feed is disabled. Specifying the MIN parameter returns a value of 0. Specifying

the MAX parameter returns a value of 1. Specifying the DEF parameter returns

a value of 1.

116

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.9.14

8.4.9.15

SYSTem:COMMunicate:SERial:LINefeed <bool>|MIN|MAX|DEF

Sets the state of the serial port linefeed setting.

SYST:COMM:SER:LIN ON

The <bool> parameter turns linefeed on (1 or ON) or off (0 or OFF). Spec-

ifying the MIN, MAX, or DEF parameter sets the linefeed to the minimum,

maximum, or default respectively.

SYSTem:COMMunicate:SERial:TIMe? [MIN|MAX|DEF]

Returns the serial port sample period setting.

SYST:COMM:SER:TIM?

Specifying the MIN parameter returns a value of 0.1. Specifying the MAX pa-

rameter returns a value of 3600. Specifying the DEF parameter returns a value

of 1.

8.4.9.16

SYSTem:COMMunicate:SERial:TIMe <num>MIN|MAX|DEF

Sets to serial port sample period setting.

SYST:COMM:SER:TIM 10

The <num> parameter can be one of the following values: 0.1, 0.2, 0.5, 1, 2, 5,

10, 30, 60, 120, 300, 600, 1800 or 3600. The units are seconds. If a value other

than one listed here is used, the instrument automatically selects the nearest ac-

ceptable value that is less than the value entered. Values greater than 3600 or

less than 0.1 are ignored. Specifying the MIN, MAX or DEF parameter sets the

sample period setting to the minimum, maximum, or default value respectively.

8.4.9.17

SYSTem:KLOCkout? [MIN|MAX|DEF]

Returns the state of the keypad lockout.

SYST:KLOC?

A value of 1 is returned if the keypad is locked out. A value of 0 is returned if

the keypad is enabled (unlocked). Specifying the MIN parameter returns a

value of 0. Specifying the MAX parameter returns a value of 1. Specifying the

DEF parameter returns a value of 0.

8.4.9.18

SYSTem:KLOCkout <bool>|MIN|MAX|DEF

Sets the state of the keypad lockout.

SYST:KLOC 1

117

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The <bool> parameter turns the keypad lockout on (1 or ON) or off (0 or OFF).

Specifying the MIN, MAX, or DEF parameter sets the keypad lockout to the

minimum, maximum, or default respectively.

8.4.9.19

SYSTem:POWer:BATTery?

Returns the current battery charge level.

SYST:POW:BATT?

The returned value indicates the current percentage of charge remaining in the

battery. The battery charge level is approximate and should be used only as a

guideline.

8.4.9.20

SYSTem:POWer:SOURce?

Returns the source of power being used.

SYST:POW:SOUR?

Indicates whether the instrument is operating on the battery or the AC adapter.

This command returns a 1 if the AC adapter is connected or a 0 if the instru-

ment is running on the battery. The battery percentage is approximate and

should only be used as a general guideline when determining the amount of

charge remaining.

8.4.10

Date and Time Commands

The date and time commands are used for querying and setting the instrument

date and time and the format that is used when displaying the date and time.

8.4.10.1

DISPlay:DATE:FORMat? [MIN|MAX|DEF]

Returns a number indicating the current date format.

DISP:DATE:FORM?

The returned value is either a 0, 1, 2, or 3. See Table 11 on page 130, Date For-

mats, for a list of acceptable date formats. Specifying the MIN parameter re-

turns a value of 0. Specifying the MAX parameter returns a value of 3.

Specifying the DEF parameter returns a value of 0.

8.4.10.2

DISPlay:DATE:FORMat <num>|MIN|MAX|DEF

Sets the date format setting.

DISP:DATE:FORM 1

118

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

The <num> parameter specifies the number of the desired date format. See Ta-

ble 11 on page 130, Date Formats, for a list of acceptable time formats. Spec-

ifying the MIN, MAX, or DEF parameter sets the date format to the minimum,

maximum, or default respectively.

8.4.10.3

DISPlay:TIME:FORMat? [MIN|MAX|DEF]

Returns a number indicating the current time format.

DISP:TIME:FORM?

The return value is either a 0 or 1. See Table 12 on page 130, Time Formats, for

a list of acceptable time formats. Specifying the MIN parameter returns a value

of 0. Specifying the MAX parameter returns a value of 1. Specifying the DEF

parameter returns a value of 1.

8.4.10.4

DISPlay:TIME:FORMat <num>|MIN|MAX|DEF

Sets the time format setting.

DISP:TIME:FORM 1

The <num> parameter specifies the number of the desired time format. See Ta-

ble 12 on page 130, Time Formats, for a list of acceptable time formats. Spec-

ifying the MIN, MAX, or DEF parameter sets the time format to the minimum,

maximum, or default respectively.

8.4.10.5

SYSTem:DATE? [MIN|MAX|DEF]

Returns the current system date.

SYST:DATE?

2000,9,1

The response is returned in the format, <year>,<month>,<day>. Specifying the

MIN parameter returns a value of 2000,1,1. Specifying the MAX parameter re-

turns a value of 2099,12,31. Specifying the DEF parameter returns a value of

2000,1,1.

8.4.10.6

SYSTem:DATE <year>,<month>,<day>

Sets the system date to the specified year, month, and day.

SYST:DATE 2000,8,24

The <year>, <month>, and <day> parameters must all be supplied. The <year>

parameter is a four-digit number (2000 to 2099). The <month> parameter is a

one or two-digit number (1 to 12). The <day> parameter is a one or two-digit

number (1 to 31). Specifying the MIN, MAX or DEF parameter sets the system

date to the minimum, maximum, or default value respectively.

119

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.10.7

SYSTem:TIME?

Returns the current system time.

SYST:TIME?

11,43,23

The response is returned in the format, <hour>,<minute>,<second>.

Note: The system time is always returned using 24-hour format regardless of

the current time format setting.

8.4.10.8

SYSTem:TIME <hour>,<minute>,<second>

Sets the current system time to the specified hour, minute, and second.

SYST:TIME 11,43,23

The <hour>, <minute>, and <second> parameters must all be supplied. The

<hour> parameter is a one or two-digit number (0 to 23). The <minute> param-

eter is a one or two-digit number (0 to 59). The <second> parameter is a one or

two-digit number (0 to 59).

Note: The system time is always set using 24-hour format regardless of the cur-

rent time setting.

8.4.11

Password Commands

The password commands are used for enabling and disabling the password-pro-

tected commands, for querying and setting the probe password-protected state,

and for setting a new password.

8.4.11.1

SYSTem:PASSword:CDISable

Disables password protected commands.

SYST:PASS:CDIS

Sending this command prevents the user from accessing the password-pro-

tected settings.

8.4.11.2

8.4.11.3

SYSTem:PASSword:CENable <pass>

Enables password protected commands.

SYST:PASS:CEN 1234

The <pass> parameter is the current system password. This command must be

sent to allow the user to access password-protected settings. After sending this

command, use the SYST:PASS:CEN:STAT? command to verify success.

SYSTem:PASSword:CENable:STATe?

Returns the current password protection state.

120

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

SYST:PASS:CEN:STAT?

The response is either 0 (disabled) or 1 (enabled). A response of 0 indicates

password-protected settings cannot be accessed. A response of 1 indicates the

password was successfully entered and password-protected settings can be

accessed.

8.4.11.4

SYSTem:PASSword:CONVersion? [MIN|MAX|DEF]

Returns the current probe password-protected state.

SYST:PASS:CONV?

If the response to this command is 0, the indicated conversion settings are not

password-protected and can be accessed without having to enter the password.

If the response to this command is 1, the indicated conversion settings are pass-

word-protected and the password must be entered before they can be accessed.

Specifying the MIN parameter returns a value of 0. Specifying the MAX pa-

rameter returns a value of 1. Specifying the DEF parameter returns a value of 0.

8.4.11.5

SYSTem:PASSword:CONVersion <bool>|MIN|MAX|DEF

Sets the probe password-protection state.

SYST:PASS:CONV 0

The <bool> parameter allows the indicated conversion settings to be password

protected (1 or ON) or not (0 or OFF). Setting this to 1 requires the password to

be entered before the indicated conversion settings can be accessed. Setting this

to 0 allows the indicated conversion settings to be accessed without having to

enter the password. This command is password protected. To access this com-

mand, the password must be successfully entered using the SYST:PASS:CEN

<pass> command (see section 9.4.11, Password Commands).

8.4.11.6

SYSTem:PASSword:NEW <pass>

Sets the current system password to a new password.

SYST:PASS:NEW 1212

The <pass> parameter must be a 4-digit number (0000 to 9999). The password

is required to access the indicated settings. This command is password pro-

tected. To access this command, the password must be successfully entered us-

ing the SYST:PASS:CEN <pass> command (see Section 9.4.11, Password

Commands).

121

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.12

Status Commands

The status commands are used for querying and setting the state of the instru-

ment registers. For details on the operation of the status registers refer to the

IEEE-488.2 and SCPI standards.

8.4.12.1

8.4.12.2

*CLS

Clears the status registers.

*CLS

*ESE?

Returns the Event Status Enable Register.

*ESE?

255

8.4.12.3

8.4.12.4

*ESE <num>|MIN|MAX|DEF

Sets the Event Status Enable Register.

*ESE 48

*ESR?

Returns the Event Status Register.

*ESR?

8.4.12.5

*SRE?

Returns the Service Request Enable Register.

*SRE?

8.4.12.6

8.4.12.7

*SRE <num>|MIN|MAX|DEF

Sets the Service Request Enable Register.

*SRE 32

*STB?

Returns the Status Byte Register.

*STB?

200

122

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

8.4.12.8

8.4.12.9

*TST?

Performs a self-test and reports any errors that are found.

*TST?

STATus:MEASure?

Reads and clears the Measurement Status Register.

STAT:MEAS?

The assignment of the bits in this register is as follows:

bit 0: channel 1 measurement complete

bit 1: channel 2 measurement complete

bit 2: channel 3 measurement complete

bit 3: channel 4 measurement complete

bits 4-15: not used

8.4.12.10

STATus:MEASure:CONDition?

Returns the Measurement Status Condition Register.

STAT:MEAS:COND?

The assignment of the bits in this register is as follows:

bit 0: channel 1 measurement in process

bit 1: channel 2 measurement in process

bit 2: channel 3 measurement in process

bit 3: channel 4 measurement in process

bits 4-15: not used

8.4.12.11

8.4.12.12

STATus:MEASure:ENABle?

Returns the Measurement Status Enable Register.

STAT:MEAS:ENAB?

255

STATus:MEASure:ENABle <num>

Sets the Measurement Status Enable Register.

123

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

STAT:MEAS:ENAB 15

8.4.12.13

8.4.12.14

8.4.12.15

STATus:OPERation?

Reads and clears the Operation Status Register.

STAT:OPER?

The assignment of the bits in this register is as follows:

bits 0-3: not used

bit 4: measurement complete

bits 5-15: not used

STATus:OPERation:CONDition?

Returns the Operation Status Condition Register.

STAT:OPER:COND?

The assignment of the bits in this register is as follows:

bits 0-3: not used

bit 4: measurement in process

bits 5-15: not used

STATus:OPERation:ENABle?[MIN|MAX|DEF]

Returns the Operation Status Enable Register.

STAT:OPER:ENAB?

255

8.4.12.16

8.4.12.17

STATus:OPERation:ENABle <num>|MIN|MAX|DEF

Sets the Operation Status Enable Register.

STAT:OPER:ENAB 16

STATus:QUEStionable?

Reads and clears the Questionable Status Register.

STAT:QUES?

The assignment of the bits in this register is as follows:

bits 0-3: not used

124

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

bit 4: measurement invalid

bits 5-15: not used

8.4.12.18

STATus:QUEStionable:CONDition?

Returns the Questionable Status Condition Register.

STAT:QUES:COND?

The assignment of the bits in this register is as follows:

bits 0-3: not used

bit 4: measurement invalid

bits 5-15: not used

8.4.12.19

8.4.12.20

STATus:QUEStionable:ENABle? [MIN|MAX|DEF]

Returns the Questionable Status Enable Register.

STAT:QUES:ENAB?

255

STATus:QUEStionable:ENABle <num>|MIN|MAX|DEF

Sets the Questionable Status Enable Register.

STAT:QUES:ENAB 10

125

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.13

Statistical Calculation Types

The statistical calculation types are listed in the following table.

Table 4 Statistical Calculation Types

Number

Type

Keyword

AVE

Average

Standard Deviation

Minimum

STD

MIN

Maximum

MAX

SPR

Spread

N (Number of Samples)

STN

8.4.14

Field Types

The bottom portion of the main display is capable of showing up to eight fields.

These fields are selectable from the following table.

Table 5 Field Types

Number

Keyword

----

Field Type

None

DATE

TIME

TYP

SER

INP

Date

Time

Conversion Type

Probe Serial Number

Input

REF

TEM

-T1

Reference

Temperature

Delta Between Specified Channel and Channel 1

-T2

Delta Between Specified Channel and Channel 2

-T3

Delta Between Specified Channel and Channel 3

-T4

Delta Between Specified Channel and Channel 4

AVE

STD

MIN

Average

Standard Deviation

Minimum

MAX

SPR

STN

Maximum

Spread

Statistical n (Number of Measurements Comprising Statistics)

126

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

Number

Keyword

ALOG

Field Type

Logging Indicator

Battery Percent Remaining

BATT

MEAS

Number of Seconds Until Next Measurement

Note: When the field type reference (REF) is selected, the displayed keyword

changes depending on the probe type. The reference display keywords are de-

tailed in the following table.

Table 6 Reference (REF) Keywords

Probe Type

Keyword

RIN

Description

Resistance

R(0.01°C)

RES

ITS-90

RTP

ITS-SR5

PT-100

CVD

R(0°C)

THERM-R

THERM-T

YSI-400

R25

R(25°C)

VIN[mV]

RJT

Reference Junction Temperature

Thermocouples

127

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.15

Conversion Types and Parameters

Table 7 lists the probe types, conversion types, mnemonics, and serial port re-

sponses. Table 8 lists the conversioin types and their parameters.

Table 7 Conversion Types, Mnemonics, and Serial Port Responses

Probe Type

Conversion Type

Mnemonic

Port Response

SPRT, PRT, RTD,

Thermistor

ITS-90 (default)

ITS-SR5

PT-100

ITS-90

ITS-SR5

PT100

ITS

ITS5

CVD

TRES

TTEM

YSI

THRM R(T)

THRM T(R)

YSI-400

THERM-R

THERM-T

YSI-400

RES

R(W)

RES

Thermocouple

TC-K (default)

MilliVolts

TC-B

TC-E

TC-J

TC-K

VIN[mV]

TC-B

TC-E

TC-J

TC-N

TC-R

TC-N

TC-R

TC-S

TC-T

TC-S

TC-T

AuPT

POLY

TC-AU/PT

Polynomial

TC-AU/PT

TC-POLY

Table 8 Conversion Types and Parameters

Conversion Type

Parameters

I90

Range, Wires, RTPW, A4, B4, A, B, C, D

Range, Wires, RTPW, A5, B5

Range, Wires

Range, Wires, R0, AL, DE, BE

Range, Wires

ITS-SR5

PT100

CVD

YSI-400

RES

Range Wires

THERM-R

THERM-T

B0, B1, B2, B3

A0, A1, A2, A3

128

Download from Www.Somanuals.com. All Manuals Search And Download.

8 Digital Communications Interface

Commands

Conversion Type

Parameters

TC-K

VIN[mV]

TC-B

TC-E

TC-J

TC-N

TC-R

TC-S

TC-T

RJC, RJT, T1, ADJ1, T2, ADJ2, T3, ADJ3

<none>

RJC, RJT, T1, ADJ1, T2, ADJ2, T3, ADJ3

RJC, RJT, mV(25C), C0, C1, C2, C3, C4, C5, C6

TC-AU/PT

TC-POLY

The following table lists the RJC settings and their corsponding number.

Table 9 RJC Settings

Number

Setting

External

Internal

8.4.16

Port Numbers

The following table lists the communication ports and their number setting.

Table 10 Port Numbers

Number

Port

Serial (default)

129

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

8.4.17

Date and Time Formats

The following tables list the acceptable date and time formats and their number

setting.

Table 11 Date Formats

Number

Format

MM-DD-YY

MM-DD-YYYY

DD/MM/YY

DD/MM/YYYY

Table 12 Time Formats

Number

Format

H:MM:SSAM/PM (12-hour format)

HH:MM:SS (24-hour format)

130

Download from Www.Somanuals.com. All Manuals Search And Download.

9 Calibration

PRT and Thermistor Calibration

Calibration

Each channel of the 1529 is calibrated independently of the other channels and

has its own set of calibration parameters. The 1529 should be calibrated at reg-

ular intervals to ensure that it continues to measure with proper accuracy. Cali-

bration should only be done by qualified, authorized personnel. When the 1529

is recalibrated, all four channels are calibrated each calibration cycle. The cali-

bration label indicates the calibration date and recalibration due date for the en-

tire instrument.

9.1

PRT and Thermistor Calibration

The following information is for PRT and thermistor channel calibrations. The

adjustable parameters are listed in the following table.

Table 13 PRT and Thermistor Calibration Parameter Description

Parameter

Description

PRT offset parameter

PRT scale parameter

C100

C400

C0K

PRT linearity parameter

Thermistor offset parameter

Thermistor scale parameter

Thermistor linearity parameter

C10K

C100K

DATE

Records the date the PRT or Thermistor channel

was calibrated

DUE

Record the date the PRT or Thermistor channel cali-

bration expires

9.1.1

PRT Calibration Parameters

Three adjustable parameters are used for calibration: C0, C100, and C400. The

C0 parameter directly affects the measurement at 0Ω. It has negligible effect at

100Ω but significant affect at higher resistances. The C100 parameter directly

affects the measurement at 100Ω. It has negligible effect at 0Ω and proportion-

ately greater effect the higher the resistance. The C400 parameter directly af-

fects the measurement at 400. It has negligible effect at 0Ω and 100Ω with

greater effect as the resistance increases. Each of the parameters has positive ef-

fect at their primary resistances: increasing the value of the parameter increases

the measured resistance. The theoretically normal value for each is 0.

131

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

The calibration parameters C0, C100, and C400 can be adjusted to optimize the

accuracy. These password-protected parameters are accessed from the CALI-

BRATION function of the SYSTEM menu.

9.1.2

PRT Calibration Procedure

Calibration requires adjustment of the C0, C100, and C400 parameters at three

specific input resistances. If the resistances used are approximately 0Ω, 100Ω

and 400Ω respectively the adjustments are independent and the procedure is

simple. The order in which the adjustments are performed is important. The ad-

justment of the C400 parameter must be done last as the adjustments of C0 and

C100 affect the measurement at 400Ω but C400 does not affect the measure-

ments at 0Ω or 100Ω. Each channel must be calibrated. Set the conversion type

to RES to display resistance (see Section 7.2.1.5) and the RANGE parameter to

100Ω. The calibration should be performed with a four-wire connection and

with the probe wiring parameter set to four-wire (see Section 6.4, Connecting

the Probe). The accuracy required of the resistance standards is 1/4 of the in-

strument accuracy; that is 0.000125Ω at 0Ω, 0.0006Ω ( 6 ppm) at 100Ω, and

0.0024Ω (6 ppm) at 400Ω. The recommended procedure is as follows:

Connect a 0Ω resistor to the input and measure its resistance. If a short-

ing wire is used the wire should run from the C2 terminal to the C1 ter-

minal to the P1 terminal to the P2 terminal (See Figure 50). Note the

average error in the measurement. Adjust the C0 parameter by subtract-

ing the measured error. For example, if the input is exactly 0.0000 and

the readout shows –0.0011, adjust the C0 parameter by adding 0.0011.

Figure 50 Using a Shorting Wire

Connect a 100Ω resistor (6 ppm accuracy) to the input and measure its

resistance. Note the average error in the measurement. Adjust the C100

parameter by subtracting the measured error. For example, if the input is

exactly 100.0000Ω and the readout shows 100.0295Ω, adjust the C100

parameter by subtracting 0.0295.

132

Download from Www.Somanuals.com. All Manuals Search And Download.

9 Calibration

PRT and Thermistor Calibration

Connect a 400Ω resistor (6 ppm accuracy) to the input and measure its

resistance. Note the average error in the measurement. Adjust the C400

parameter by subtracting the measured error. For example, if the input is

exactly 400.0000Ω and the readout shows 399.9913Ω, adjust the C400

parameter by adding 0.0087.

4. Record the date in the DATE parameter and set the DUE parameter to

the desired calibration interval.

Verify the accuracy at 0Ω, 25Ω or 50Ω, 100Ω, 200Ω, and 400Ω on each

channel.

9.1.3

Thermistor Calibration Parameters

Three adjustable parameters are used for calibration: C0K, C10K, and C100K.

The C0K directly affects the measurement at 0Ω. It has negligible effect at 10

kΩ but significant affect at higher resistances. The C10K directly affects the

measurement at 10 kΩ. It has negligible effect at 0Ω and proportionately

greater effect the higher the resistance. The C100K directly affects the mea-

surement at 100 kΩ. It has negligible effect at 0Ω and 10 kΩ with greater effect

as the resistance increases. Each of the parameters has positive effect at their

primary resistances: increasing the value of the parameter increases the mea-

sured resistance. The theoretically normal value for each is 0.

The calibration parameters C0K, C10K, and C100K can be adjusted to opti-

mize the accuracy. These parameters are accessed from the CALIBRATION

function of SYSTEM menu.

9.1.4

Thermistor Calibration Procedure

Calibration requires adjustment of the C0K, C10K, and C100K parameters at

three specific input resistances. If the resistances used are approximately 0Ω,

10 kΩ and 100 kΩ respectively the adjustments are independent and the proce-

dure is simple. The order in which the adjustments are performed is important.

The adjustment of the C100K parameter must be done last as the adjustments

of C0K and C10K affect the measurement at 100 kΩ but C100K does not affect

the measurements at 0Ω or 10 kΩ. Each channel must be calibrated. Set the

conversion type to RES to display resistance and set the RANGE parameter to

10KΩ. The accuracy required of the resistance standards is 1/4 of the instru-

ment accuracy; that is 0.12Ω at 0Ω, 0.25Ω (25 ppm) at 10 kΩ, and 2.5Ω (25

ppm) at 100 kΩ. The recommended procedure is as follows:

Connect a 0Ω resistor to the input and measure its resistance. If a short-

ing wire is used the wire should run from the C2 terminal to the C1 ter-

minal to the P1 terminal to the P2 terminal (See Figure 50 on page 132).

Note the average error in the measurement. Adjust the C0K parameter by

subtracting the measured error. For example, if the input is exactly 0.0Ω

and the readout shows –0.11Ω, adjust the C0K parameter by adding

0.11.

133

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Connect a 10 kΩ resistor (25 ppm accuracy) to the input and measure its

resistance. Note the average error in the measurement. Adjust the C10K

parameter by subtracting the measured error. For example, if the input is

exactly 10.00000 kΩ and the readout shows 10.00295 kΩ, adjust the

C10K parameter by subtracting 2.95.

Connect a 100 kΩ resistor (25 ppm accuracy) to the input and measure

its resistance. Note the average error in the measurement. Adjust the

C100K parameter by subtracting the measured error. For example, if the

input is exactly 100.0000 kΩ and the readout shows 99.9913 kΩ, adjust

the C100K parameter by adding 8.7.

4. Record the date in the DATE parameter and set the DUE parameter to

the desired calibration interval.

Verify the accuracy at 0Ω, 4kΩ, 10kΩ, 40kΩ, 100kΩ, and 500kΩ on

each channel.

9.2

Thermocouple Calibration

The following information is for a Thermocouple calibration. See Section 9.1

for PRT and thermistor calibrations.

9.2.1

Calibration Parameters

Three adjustable parameters are used for calibration of each thermocouple

channel. They are listed in Table 14, Calibration Parameters.

134

Download from Www.Somanuals.com. All Manuals Search And Download.

9 Calibration

Thermocouple Calibration

Table 14 Calibration Parameters

Parameter

Description

Adjusts the voltage accuracy of at 0 mV

Adjusts the voltage accuracy of at 100 mV

Adjusts the internal RJC accuracy

C100

CRJ

DATE

DUE

Records the date the thermocouple channel was calibrated

Records the date the thermocouple channel calibration expires

The calibration parameters can be accessed from the CALIBRATION function

of SYSTEM menu

9.2.2

Calibration Procedure

Calibration of each channel is performed in two steps. First the voltage mea-

surement is calibrated then the internal RJC is calibrated. The equipment re-

quired are a programmable voltage source, a precision voltmeter with an

accuracy of 10 ppm or better, a thermocouple (preferably type E), and a tem-

perature source between 0 and 30°C. The combined accuracy of the reference

thermocouple and temperature source must be 0.06°C or better between the ref-

erence temperature and ambient temperature. At each step during the calibra-

tion procedure the readings should be allowed to settle for at least two minutes

before recording the measurement. Also, the 1529 should be allowed to warm

up for at least one hour after power up prior to calibration. The recommended

procedure is as follows:

1. Connect the voltage source to the thermocouple channel, set it for 0 mV,

and measure the voltage with the 1529 and the voltmeter simultaneously.

Adjust the C0 parameter by subtracting the measured error. For example,

if the 1529 measures –0.0006 mV, adjust the C0 parameter by adding

0.0006. If it was previously 0.0000 it should now be 0.0006.

2. Set the voltage source to 100 mV and measure the voltage with the 1529

and the voltmeter simultaneously. Adjust the C100 parameter by sub-

tracting the measured error. For example, if the input is exactly 100.0000

mV and the 1529 shows 100.2953 mV, the C100 parameter should be ad-

justed by subtracting 0.2953. If it was previously 0.0000 it should now

be –0.2953.

3. Verify the voltage accuracy at 0, 50, and 100 mV. The accuracy must be

within the short-term voltage accuracy given in the specifications.

4. Connect the calibrated thermocouple to the thermocouple channel and

insert the thermocouple into the temperature source. Measure the tem-

perature with the 1529 (be sure to program the channel with the correct

thermocouple type). Adjust the CRJ parameter by subtracting the mea-

135

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

sured error. For example, if the thermocouple temperature is actually

0.0°C but the 1529 reads 0.184°C, the CRJ parameter should be adjusted

by subtracting 0.184. If it was previously 0.000 it should now be –0.184.

6. Record the date with the DATE parameter. Set the DUE date to the de-

sired calibration interval.

7. Repeat the procedure for any other thermocouple channels.

136

Download from Www.Somanuals.com. All Manuals Search And Download.

10 Maintenance

Maintenance

• The calibration instrument has been designed with the utmost care. Ease

of operation and simplicity of maintenance have been a central theme in

the product development. Therefore, with proper care the instrument

should require very little maintenance. Avoid operating the instrument in

oily, wet, dirty, or dusty environments.

• If the outside of the instrument becomes soiled, it may be wiped clean

with a damp cloth and mild detergent. Do not use harsh chemicals on the

surface, which may damage the LCD or the plastic front panel.

• If a hazardous material is spilt on or inside the equipment, the user is re-

sponsible for taking the appropriate decontamination steps as outlined by

the national safety council with respect to the material.

• Before using any cleaning or decontamination method except those rec-

ommended by Hart, users should check with a Hart Authorized Service

Center (see Section 1.3) to be sure that the proposed method will not

damage the equipment.

• If the AC adapter becomes damaged, have it replaced immediately. Never

disassemble the AC adapter or attempt to repair it.

• If the instrument is used in a manner not in accordance with the equip-

ment design, the operation of the thermometer readout may be impaired

or safety hazards may arise.

• Periodic calibration of the instrument at regular intervals is required to en-

sure that it continues to measure with proper accuracy. Calibration should

only be performed by qualified authorized personnel.

137

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Troubleshooting

Troubleshooting

In case you run into difficulty while operating the 1529 system, this section

provides some suggestions that may help you solve the problem. Below are

several situations that may arise followed by possible causes and suggested ac-

tions you might take.

11.1

Troubleshooting

The following table lists possible error messages, their causes, and suggested

actions.

Problem

Incorrect temperature reading

Solution

While attempting to measure temperature, the display shows an incorrect value or no value at all

( . . . . . . . . . ).

• If the temperature readings seem to be incorrect you should first check to see if the

resistance, or voltage in the case of thermocouples, is being measured correctly.

Set up the display to show the resistance or voltage for the channel.

• If the resistance or voltage is incorrect refer to the next subsection for troubleshoot-

ing incorrect resistance or voltage readings.

• If the resistance or voltage is being measured correctly but the displayed tempera-

ture value is incorrect consider the following possibilities:

One or more coefficients are incorrect. This is a common mistake. While entering coefficients

it is easy to miss a digit or sign. Check all the values carefully using the EDIT PROBE function

(see Section 7.2.1) comparing them with the values on the calibration certificate for the probe.

Use the TEST PROBE function to test the coefficients (see Section 7.2.1.10, Standard Thermo-

couple Conversions).

The selected conversion type is incorrect. Check to make sure the correct conversion type is

selected. In the case of thermocouples, make sure you have selected the correct type. You

should also make sure that you have selected the proper reference junction compensation (RJC)

made for your application (see Section 7.2.1.10, Standard Thermocouple Conversions). You

can use the TEST PROBE function to test the temperature conversion calculation.

The measurement is out of range. The 1529 may not be able to calculate temperature accu-

rately if the resistance or voltage is outside the valid range. The measured resistance or voltage

may be too low or too high if the actual temperature is too low or too high or if there is a problem

with the sensor.

• The measure period may be set to a long interval. Check the measure period set-

ting.

139

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

Problem

Solution

Incorrect resistance or voltage

reading

While attempting to measure resistance or voltage, the display shows an incorrect value or no value at

all

(. . . . . . . . . . ).

Consider the following possibilities:

Poor or incorrect connection of the probe. A common mistake is to connect the wires of the probe

to the wrong terminals. Check the wiring carefully, especially when using a four-wire PRT (see Section

6.4.1). Make sure the lead wires are fastened down tightly.

Open, shorted, or damaged sensor or lead wires. In the case of resistance sensors check the resis-

tance across the sensor using a hand-held DMM. Also check the resistance between common pairs of

leads. Check to make sure there is no conductivity between any of the leads and the probe sheath.

Use a good-quality sensor to avoid errors caused by drift, hysteresis, or insulation leakage. In the case

of thermocouples, use a hand-held DMM to check its voltage.

Improper setting for three or four-wire probe. Make sure the correct wiring type is selected Select-

ing three-wire input while using four-wire probes may cause errors of 0.01 to 0.1 ohms. Selecting

four-wire input while using three-wire probes will result in erratic or out-of-range readings (see Section

7.2.1.1).

Electrical interference. Intense radio-frequency radiation near the 1529 or probes can induce noise

into the measurement circuits resulting in erratic readings. The 1529 is intended to operate in a labora-

tory environment with limited radio-frequency noise. If interference seems to be a problem you might

try eliminating the source of interference or moving the 1529 to a different location. A well-grounded,

shielded cable should be used for the probe leads.

Stem conduction error. The problem may be that the actual temperature of the sensor is not what

you expect. This is often the result of stem conduction where heat flowing through the stem of the

probe to ambient affects the temperature of the probe. It is very important that probes be inserted to an

adequate depth into the material being measured. Measuring temperature using a surface sensor can

be especially difficult as the sensor is directly exposed to ambient.

Wrong calibration parameters. The problem may be that the calibration parameters for the 1529 are

invalid. Check the parameters currently stored in the unit against those listed on the 1529 Report of

Calibration.

Blank screen

The screen lights up when the 1529 is switched on but the screen appears blank. This problem

can be caused by improper adjustment of the contrast. After the power is switched on allow the 1529

at least one minute to complete its self-test and power on sequence. Then, try to adjust the contrast

using the contrast buttons.

Error message at power up

The 1529 reports an error during the power up self-test. On power up the 1529 performs a series of

self-tests to check the operation of all its components and each of the modules. The results of the

self-tests are reported on the screen. Normally, all tests report ‘OK’. Below is a table of error messages

and recommended actions to correct the error. Often these errors can be corrected by completing the

actions listed. A failure of one or more component causes error messages to be reported. Component

failures generally require a qualified factory technician to replace the faulty component. Contact a Hart

Authorized Service Center (see Section 1.3).

Temperature not

updating

The 1529 measure period may be set to a long interval. Check the measure period.

11.1.1

Self-Test Error Messages

The following messages may appear during the self-test. If the recommended

action fails to correct the error, contact a Hart Authorized Service Center (see

Section 1.3) for assistance.

Message

Recommended Action

SYSTEMS: INVALID TIME

Set the date and time.

SYSTEMS: SERIAL PORT FAILURE

Cycle the power.

140

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Troubleshooting

Downloading Auto Logged Data

Message

Recommended Action

SYSTEMS: IR PORT FAILURE

Cycle the power.

SYSTEMS: BATTERY NOT

INSTALLED

Cycle the power.

Check that the battery is properly connected.

Replace the battery.

CHANNELS: FAILURE

Cycle the power.

CALIBRATION: DUE FOR RECAL

Check that the instrument date is correct.

Recalibrate the instrument and set the recalibration date accordingly.

CALIBRATION: INVALID

PARAMETERS

Check the correctness of the calibration parameters for each channel.

GPIB: NOT INSTALLED

Normal message if the IEEE-488 option is not installed.

Reset the memory by pressing EXIT when prompted.

MEMORY DATA: QUESTIONABLE

MEMORY DATA: INVALID DATA

Reset the memory by pressing ENTER when prompted. (This action requires that important data

such as probe coefficients be restored.

BUTTONS: [button name]

Check the stated button to ensure that it is not stuck. Loosen as necessary.

11.1.2

Start-up Error Messages

The following messages may appear after the self-test. If the recommended ac-

tion fails to correct the error, contact a Hart Authorized Service Center (see

Section 1.3) for assistance.

Message

CALIBRATION EXPIRED

Recommended Action

Check that the instrument date is correct.

Recalibrate the instrument and set the recalibration date accordingly.

INVALID CALIBRATION PARAMETERS

MEMORY QUESTIONABLE

Check the correctness of the calibration parameters for each channel.

Reset the memory by pressing EXIT when prompted.

MEMORY DATA INVALID, MEMORY WILL BE

CLEARED

Reset the memory by pressing ENTER. (This action requires that important data

such as probe coefficients be restored.)

11.2

Downloading Auto Logged Data

The 1529 “Chub-E4” Thermometer Readout stores up to 8,160 autolog read-

ings or 100 demand log readings in its memory. These readings can be down-

loaded to a computer using the RS-232 serial port.

The following steps should be followed to download logged data using the se-

rial port:

1. Connect the 1529 to a COM port on the computer using the serial cable.

2. Run a terminal program such as Windows® Terminal or HyperTerminal®.

141

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

a) Set up the terminal program to use the correct COM port and baud

rate. Configure the communication settings to use 8 data bits, 1 stop bit,

no parity and no flow control.

b) If you want to save the downloaded data to a file, configure your ter-

minal program to capture the incoming text and save it to a text file. Re-

fer to your terminal program’s documentation for details on how to do

this.

3. Determine how many logged readings are stored in the 1529’s memory.

a) For the autolog, send the command “LOG:AUT:POIN?”. If the response to

this command is “0”, there are no autolog readings to download.

b) For the demand log, send the command “LOG:DEM:POIN?”. If the re-

sponse to this command is “0”, there are no demand log readings to download.

4. Begin downloading the data.

a) To begin downloading the autolog data, send the command

“LOG:AUT:PRIN” to initiate the download process.

b) To begin downloading the demand log data, send the command

“LOG:DEM:PRIN” to initiate the download process.

c) The 1529 should immediately begin downloading the data. If no readings

have been stored, the 1529 will not respond to these commands. For more de-

tails on using these commands, see Sections 9.4.7.8 and 9.4.7.19.

5. If the terminal program was set to capture the incoming data to a file, wait

until no more data is being received, then stop capturing.

The autolog and demand log readings can also be downloaded using the IR port

with the 9935 LogWare software.

11.3

Placement of IR Dongle for Transfer of Data

The 1529 can be used with the 2374 I/R Dongle and the 9935 LogWare soft-

ware to collect data via the IR interface. The I/R Dongle must be placed near

the IR port of the 1529 between 3 and 12 inches (8 and 30 cm) and pointed di-

rectly at and perpendicular to the IR window.

11.4

CE Comments

11.4.1

EMC Directive

Hart Scientifics’ equipment has been tested to meet the European Electromag-

netic Compatibility Directive (EMC Directive, 89/336/EEC). The Declaration

of Conformity for your instrument lists the specific standards to which the unit

was tested.

142

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Troubleshooting

Frequently Asked Questions

The instrument was designed specifically as a test and measuring device. Com-

pliance to the EMC directive is through IEC 61326-1 Electrical equipment for

measurement, control and laboratory use – EMC requirements (1998).

As noted in the IEC 61326-1, the instrument can have varying configurations.

The instrument was tested in a typical configuration with shielded, grounded

probe and RS-232 cables. Emissions may, in non-typical applications, exceed

the levels required by the standard. It is not practical to test all configurations,

as the manufacturer has no control over the probes the user may connect to the

instrument.

11.4.1.1

Immunity Testing

The instrument was tested to the requirements for industrial locations. This al-

lows the instrument to be used in all types of locations from the laboratory to

the factory floor. Criterion B was used for Radiated RF (IEC 61000-4-3) and

Conducted RF (IEC 61000-4-6). Therefore, the operation of the instrument

may be affected by excessive electromagnetic interference and the instrument

may not perform within the normal specification limits in such an environment.

Criterion C was used for Electrostatic Discharge (ESD, IEC 61000-4-2) and

Electric Fast Transit (EFT, Burst, IEC 61000-4-4). If the instrument is sub-

jected to EFT conditions at 2kV, the instrument may require the user to cycle

the power to return to normal operation.

11.4.1.2

Emission Testing

The instrument fulfills the limit requirements for Class A equipment but does

not fulfill the limit requirements for Class B equipment. The instrument was

not designed to be used in domestic establishments.

11.4.2

Low Voltage Directive (Safety)

In order to comply with the European Low Voltage Directive (73/23/EEC),

Hart Scientific equipment has been designed to meet the IEC 1010-1 (EN

61010-1) and the IEC 1010-2-010 (EN 61010-2-010) standards.

11.5

Frequently Asked Questions

11.5.1

Battery

1. What type of batteries does the Model 1529 use? The Model 1529 uses a

built-in Nickel-Metal-Hydride battery pack.

2. How long do I need to charge the battery initially? The batteries come

fully charged. If for some reason they are not fully charged, the front

panel indicator shows this and you can recharge them as needed.

3. How long does the battery take to fully charge? About 3 hours from

fully discharged.

143

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

4. How long does the battery last from full charge? About 8 hours from

full charge with the backlight off.

5. How do I know when the battery is at full charge? The charging indica-

tor LED located on the back panel displays amber while charging and

then turns green when the batteries are fully charged (only when the AC

adapter is connected). The front panel indicator at the bottom right

shows when the batteries are in use and their approximate charge state.

6. How does the backlight affect the battery life? With the backlight on low

the battery life is reduced by 25%, medium by 30%, and high by 40%.

7. Do I have to let the battery fully discharge before charging? No, the bat-

teries do not need to be fully discharged before recharging. You may re-

charge them at any time.

8. Is it recommended that I allow the battery pack to fully discharge occa-

sionally? In order to maintain the charge/discharge characteristics of the

battery, Hart recommends that you allow the battery to discharge com-

pletely once a month. You do this by allowing the Model 1529 to operate

on battery power until it shuts down on its own.

9. If I allow the battery pack to fully discharge, what happens to the calibra-

tion parameters stored in the Model 1529? Parameters used by the Model

1529 are stored in non-volatile RAM (NVRAM). This IC stores the pa-

rameters even when power is not applied.

10. How many recharge cycles is the battery good for? Approximately 500.

11. What happens to my measurement accuracy when the battery is low?

The Model 1529 does not display temperature when there is not suffi-

cient power to make a correct measurement.

12. If I am using the autolog and the battery runs out will I lose my data?

No, you won’t lose any data. The Model 1529 simply stops logging

data. When the AC adapter is plugged in, the data logging continues.

13. How do I dispose of the batteries used in the Model 1529? Disposal

guidelines can be found by consulting your local governing authority.

14. If the AC adapter is plugged in and I have the unit turned on, is the bat-

tery still charging? Yes, the Model 1529 charges while in use without af-

fecting the charging time or its performance.

15. If I am using the Model 1529 with AC power and a power outage occurs,

will the batteries automatically take over? Yes, when AC power is re-

moved from the Model 1529 for any reason, the batteries automatically

supply back up power without risk of losing any data.

11.5.2

Input

1. Can I swap out measurement boards in the field? No, the measurement

boards were not designed to be exchanged in the field.

144

Download from Www.Somanuals.com. All Manuals Search And Download.

11 Troubleshooting

Frequently Asked Questions

2. What are the implications of the fast measurement mode in terms of ac-

curacy? Accuracy is reduced when using the Model 1529 in fast mea-

surement mode. Refer to Section 8.1.1 for a better description of the fast

measurement mode and its limitations.

3. Why can I only see one channel in the fast measurement mode? Because

of the time required to make a measurement and update the display, there

is not enough time to display more than one channel when in the fast

measurement mode.

4. Do I have to reprogram the Model 1529 each time I swap out a probe?

In addition to the four main channels, there are nine memory locations

available to store probe coefficients. If the new probe’s information has

been programmed into one of these locations, you can copy it to the

channel to which it is connected.

5. How does the moving average affect the data that is logged? The data

collected by the Model 1529 is stored as it appears on the display. If you

set the Model 1529 to average the measurements, the data it logs reflects

the moving average setting.

6. How many probe coefficients can I store? Thirteen. Four sets in the

main channels and nine sets in memory locations.

7. Are the readings really simultaneous in the simultaneous mode? Yes.

There are four measurement circuits that collect the raw data simulta-

neously. The raw data is then converted to its corresponding temperature

in sequence taking less than 0.5 seconds for all four channels.

8. How does the three-wire RTD setting affect my overall accuracy? When

using the three-wire setting in the Model 1529, a partial compensation of

lead-wire resistance is performed as per normal industry practices. Since

a three-wire measurement can’t fully compensate for lead resistaance,

accuracy is reduced. As stated in the specification section of this manual,

you need to add 0.05Ω to the measurement accuracy plus the maximum

possible difference between the resistances of the lead wires.

11.5.3

Logging

1. How many data points can the Model 1529 store? You can store up to

100 demand log readings and 8,000 autolog readings.

2. What happens when the log memory is full? Logging stops once the

memory is full. Readings are not deleted to make room for new readings.

3. How can I tell when the log memory is full? Full memory is indicated in

the log stats function in the logging menu. You can also program a field

in the lower display to show the autolog memory status.

4. Can I use the Model 1529 for other applications while I am autologging?

Yes, the Model 1529 can be used while logging. However, keep in mind

that the channels that are displayed are also logged. Changing the chan-

nels affects the data that is logged.

145

Download from Www.Somanuals.com. All Manuals Search And Download.

1529 Chub-E4 Thermometer Readout

User’s Guide

11.5.4

Output

1. How do I get data from the Model 1529 to my PC? Data can be trans-

ferred to your PC via an RS-232 interface or by IR communications

through the use of the optional IR dongle and software available through

Hart.

2. Is the IR output on the Model 1529 compatible with the IR port on my

desktop laser printer? The IR port on the Model 1529 communicates

with any IrDA compatible printer. This allows you to print to most IR

equipped laser printers. An optional IR mini-printer is also available

from Hart.

3. Can the Model 1529 be set to simultaneous measurement mode and log

to the serial port? Yes. The Model 1529 makes the measurements simul-

taneously and transmits them to the serial port. However, most printers

can’t print as fast as the data is logged so it doesn’t appear to be

simultaneous.

11.5.5

Other

1. Can I update the Model 1529 firmware without sending in my unit? Yes.

Firmware updates include a utility program that installs the upgrade via

the RS-232 port.

2. How do I change the password? Changing the password is explained in

Section 8.5.3, Password, of this manual.

3. How often does the Model 1529 need to be recalibrated? We suggest

that the unit be calibrated annually, but that may vary based upon usage

and your company’s policies.

146

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

communication 70, 79

data logging 27, 60, 141

decimal 35, 53

DELETE D A TA 5 9, 65

delta temperature 50

DEMAND LOG 54

difference temperature 50

calibration 131, 141

CALIBR A T ION EXPIRED 141

Callendar-V a n Dusen 40

channel

CLEAR S T A T S 48

coefficients

DISPL A Y O PTIONS 34

147

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

LOG S T A T S 66

MEASURE PERIOD 30, 62

measurement 15, 25

memory 141

exit 17, 29

menu 17, 29

fast measurement 26, 31

parts and controls 17

password 36, 44, 74, 76 - 77

PASSWORD 74

GPIB 79

P A SSWORD INCORRECT 36, 44, 74, 76, 78

period

measurement 30, 62

printing

coefficients 38, 41

148

Download from Www.Somanuals.com. All Manuals Search And Download.

Index

thermistor 23, 41 - 42

thermocouple 23, 43

type

range

reference junction 43, 50

reset 77

units 17, 21

resistance 41, 50

resolution 35, 53

version

wires

serial number 37, 69

S T A RT 62

statistics 48, 50

149

Download from Www.Somanuals.com. All Manuals Search And Download.

Eagle Electronics Fish Finder UltraNavGPS User Manual
Electro Voice Microphone 664 User Manual
Electro Voice Portable Speaker E V TWO User Manual
Extron electronic Network Card SMB 101 User Manual
Ferris Industries Water Heater 45495KIT User Manual
Fisher Price Motorized Toy Car M1030 User Manual
FoodSaver Food Saver V3800 series User Manual
Foster Oven KS 60 User Manual
Friedrich Air Conditioner 9368987053 User Manual
Giant Water Pump GP8045 User Manual