Induction cooktop
CI604DT, CI754DT,
and CI905DT models
Installation instructions
and User guide
NZ AU GB IE
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Contents
Safety and warnings
Installation instructions
2
6
Introduction
16
18
19
22
32
34
35
37
Choosing the right cookware
Using your induction cooktop
Using your cooktop’s special features
Cooking guidelines
Care and cleaning
Troubleshooting
Warranty and service
Important!
SAVE THESE INSTRUCTIONS
The models shown in this user guide may not be available in all markets and are
subject to change at any time. For current details about model and specification
availability in your country, please visit our local website listed on the back cover
or contact your local Fisher & Paykel dealer.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Safety and warnings
Your safety is important to us. Please read this information before using your cooktop.
Installation
WARNING!
Electrical Shock Hazard
Disconnect the appliance from the mains electricity supply before carrying
out any work or maintenance on it.
Connection to a good earth wiring system is essential and mandatory.
Alterations to the domestic wiring system must only be made by a qualified
electrician.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Safety and warnings
Important safety instructions
Read these instructions carefully before installing or using this appliance.
No combustible material or products should be placed on this appliance at any time.
Please make this information available to the person responsible for installing the appliance as it
could reduce your installation costs.
In order to avoid a hazard, this appliance must be installed according to these instructions for
installation.
This appliance is to be properly installed and earthed only by a suitably qualified person.
This appliance should be connected to a circuit which incorporates an isolating switch providing
full disconnection from the power supply.
Failure to install the appliance correctly could invalidate any warranty or liability claims.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Safety and warnings
Operation and maintenance
WARNING!
Electrical Shock Hazard
Do not cook on a broken or cracked cooktop. If the cooktop surface should
break or crack, switch the appliance off immediately at the mains power
supply (wall switch) and contact a qualified technician.
Switch the cooktop off at the wall before cleaning or maintenance.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Health Hazard
This appliance complies with electromagnetic safety standards.
However, persons with cardiac pacemakers or other electrical implants (such
as insulin pumps) must consult with their doctor or implant manufacturer
before using this appliance to make sure that their implants will not be
affected by the electromagnetic field.
Failure to follow this advice may result in death.
WARNING!
Hot Surface Hazard
During use, accessible parts of this appliance will become hot enough to
cause burns.
Do not let body, clothing or any item other than suitable cookware contact
with the ceramic glass until the surface is cool.
Never leave metal objects (such as kitchen utensils) or empty pans on the
cooktop as they can become hot very quickly.
Beware: magnetisable metal objects worn on the body may become hot in
the vicinity of the cooktop. Gold or silver jewellery will not be affected.
Keep children away.
Handles of saucepans may be hot to touch. Check saucepan handles do not
overhang other cooking zones that are on. Keep handles out of reach of
children.
Failure to follow this advice could result in burns and scalds.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Safety and warnings
WARNING!
Cut Hazard
The razor-sharp blade of a cooktop scraper is exposed when the safety
cover is retracted. Use with extreme care and always store safely and out
of reach of children.
Failure to use caution could result in injury or cuts.
Important safety instructions
Never leave the appliance unattended when in use. Boilover causes smoking and greasy
spillovers that may ignite.
Never use your appliance as a work or storage surface.
Never leave any objects or utensils on the appliance.
Do not place or leave any magnetisable objects (eg credit cards, memory cards) or electronic
devices (eg computers, MP3 players) near the appliance, as they may be affected by its
electromagnetic field.
We recommend using plastic or wooden kitchen utensils for cooking with your induction cooktop.
Never use your appliance for warming or heating the room.
After use, always turn off the cooking zones and the cooktop as described in this manual (ie by
using the touch controls). Do not rely on the pan detection feature to turn off the cooking zones
when you remove the pans.
Do not allow children to play with the appliance or sit, stand, or climb on it.
Do not store items of interest to children in cabinets above the appliance. Children climbing on
the cooktop could be seriously injured.
Do not leave children alone or unattended in the area where the appliance is in use.
Children or persons with a disability which limits their ability to use the appliance should have a
responsible and competent person to instruct them in its use. The instructor should be satisfied
that they can use the appliance without danger to themselves or their surroundings.
Do not repair or replace any part of the appliance unless specifically recommended in the
manual. All other servicing should be done by a qualified technician.
Do not use a steam cleaner to clean your cooktop.
Do not place or drop heavy objects on your cooktop.
Do not stand on your cooktop.
Do not use pans with jagged edges or drag pans across the ceramic glass surface as this can
scratch the glass.
Do not use scourers or any other harsh/abrasive cleaning agents to clean your cooktop, as these
can scratch the ceramic glass.
If the power supply cable is damaged, it must only be replaced by a qualified technician.
Do not operate your cooktop by means of an external timer or separate remote-control system.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Installation instructions
Electrical connection is
made at the right rear
Cooktop and cutout dimensions
A
B
C
E
D
G
F
Cooktop and cutout dimensions (mm)
600
530
750
530
900
530
overall width of cooktop
overall depth of cooktop
A
B
height of chassis (plastic housing incl. terminal block)
below top of bench
55
55
55
C
546
476
560
490
716
476
725
490
852
482
870
494
width of chassis (metal frame)
depth of chassis (metal frame)
overall width of cutout
D
E
F
overall depth of cutout
G
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Installation instructions
Clearances
A
WARNING!
D
This cooktop requires
B
adequate supply of cool air
to fully function.
The base of the cooktop
must have direct
C
unrestricted ventilation to
the room where the
cooktop is installed. Follow
the requirements below.
C
E
2x 50mm holes
to allow adequate
cool air
E
E
4 mm
4 mm
Top of drawer or
other obstruction
2x 50mm holes
to allow adequate
cool air
2x 50mm holes
to allow adequate
cool air
Oven with
cooling fan
500 x
500 x 10 mm
500 x 50 mm
10 mm
Fig. 1 Minimum clearances and ventilation
requirements - oven installed below cooktop
Fig. 2 Minimum clearances and ventilation
requirements - cupboard or drawer space below
Clearances (mm)
minimum clearance from rear edge of cutout to:
nearest combustible surface
A
B
C
D
E
55
650
85
55
650
78
53
minimum clearance from glass surface to:
rangehood
650
80
minimum clearance from side edges of cutout to:
nearest combustible surface
minimum clearance from benchtop to:
overhead cabinet not directly above the cooktop
450
450
450
minimum clearance below top of benchtop to:
top of oven* installed below cooktop (see Fig.1) or cabinetry
75
75
75
* The oven installed below the cooktop MUST have a cooling fan.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Installation instructions
Before you install the cooktop, make sure that
the benchtop is square and level, and no structural members interfere with space requirements
the benchtop is made of a heat-resistant material
the cooktop will not be installed directly above a dishwasher, fridge, freezer, washing machine or
clothes dryer, as the humidity may damage the cooktop electronics
if the cooktop is installed above an oven, the oven has a built-in cooling fan
the installation will comply with all clearance requirements and applicable standards and
regulations
a suitable isolating switch providing full disconnection from the mains power supply is
incorporated in the permanent wiring, mounted and positioned to comply with the local wiring
rules and regulations. The isolating switch must be of an approved type and provide a 3 mm air
gap contact separation in all poles (or in all active [phase] conductors if the local wiring rules
allow for this variation of the requirements)
the isolating switch will be easily accessible to the customer with the cooktop installed
you consult local building authorities and by-laws if in doubt regarding installation
you use heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces
surrounding the cooktop.
When you have installed the cooktop, make sure that
the power supply cable is not accessible through cupboard doors or drawers
there is adequate flow of cool air from the cabinetry to the base of the cooktop. You may
ventilate from adjacent cupboards, but ensure that the available air supply will not be restricted.
The ventilation area must be at least two ∅50mm holes or of an equivalent area.
the isolating switch is easily accessible by the customer
you complete the ‘Final checklist’ at the end of these installation instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Installation instructions
Connecting the cooktop to the mains power supply
Important!
This cooktop must be connected to the mains power supply only by a suitably qualified person.
Before connecting the cooktop to the mains power supply, check that:
1
2
3
the domestic wiring system is suitable for the power drawn by the cooktop.
the voltage corresponds to the value given in the rating plate
the power supply cable sections can withstand the load specified on the rating plate.
To connect the cooktop to the mains power supply, do not use adapters, reducers, or branching
devices, as they can cause overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its
temperature will not exceed 75oC at any point.
Power supply
CI604DT 6950W @220-240/380-415V 2N~ (30A)
CI754DT 7400W @220-240/380-415V 2N~ (32A)
CI905DT 9800W @220-240/380-415V 3N~ (42A)
Important!
Check with an electrician whether the domestic wiring system is suitable without alterations. Any
alterations must only be made by a qualified electrician.
Connection diagrams
CI604DT, CI754DT
Single-phase connection
220-240V~
Two-phase connection
380-415V 2N~
2
4
2
4
1
3
5
1
3
5
L
N
PE
L1
L2
N
PE
CI905DT
Three-phase connection
380-415V 3N~
Single-phase connection
220-240V~
2
4
2
4
1
3
5
1
3
5
L
N
PE
L
1
L2
L
3
N
PE
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Installation instructions
Applying the supplied foam seal
1
Turn the cooktop upside down and place it carefully on a soft surface.
Important!
To avoid damage to the glass, ensure there is a protective cover underneath it.
2
3
Apply the foam seal around the glass overhang, 5 mm in from the edge of the glass.
Turn the cooktop the right way up and place it into the cutout.
Clamping down the cooktop
Depending on the thickness of the benchtop, secure the supplied clamping brackets as shown.
48-65 mm
x 4
Important!
Do not overtighten the screws!
30-48 mm
x 4
Important!
Do not overtighten the screws!
Fig. 3 Clamping down the cooktop
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Installation instructions
Electrical connection is
made at the right rear
Flush mounting installation
(not recommended)
A
B
C
WARNING!
We do not recommend flush
E
D
mounting and sealing as servicing
requires the cooktop to be
removed from the benchtop. The
owner carries all risk for flush
mounting the cooktop. The owner
must ensure the cooktop has been
cut out from the benchtop before
servicing can be carried out. Fisher
& Paykel will not be liable for any
costs associated with removing
or replacing a flush-mounted
and/or sealed-in product, nor for
repairing any damage that may be
incurred by doing this.
J
G
F
H
F
FI
G GI
I
Cooktop and cutout dimensions (mm)
600
530
750
530
900
530
overall width of cooktop
overall depth of cooktop
A
B
height of chassis (plastic housing incl. terminal block)
below top of bench
55
55
55
C
546
476
716
476
755
725
535
490
852
482
905
870
535
494
width of chassis (metal frame)
depth of chassis (metal frame)
overall width of routered recess
width of cutout
D
E
F
FI
G
GI
H
I
605
560
535
overall depth of routered recess
depth of cutout
490
max. 2
5
max. 2 max. 2
corner radius of routered recess
height of routered recess
5
5
minimum clearance below top of benchtop to:
top of oven* installed below cooktop
thermal protection barrier
95
80
95
80
95
80
J
* The oven installed below the cooktop MUST have a cooling fan.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Installation instructions
Flush mounting installation (not recommended)
Important!
For any clearance or other installation requirement not specified separately for flush mounting
installation, details in the previous section (recommended method of installation) apply.
A
B
53-70 mm
Important!
Do not overtighten the screws!
35-53 mm
5 mm
Important!
Do not overtighten the screws!
C
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Installation instructions
Flush mounting installation (not recommended)
Important!
For any clearance or other installation requirement not specified separately for flush mounting
installation, details in the previous section (recommended method of installation) apply.
D
E
Ensure silicone does
not leak underneath glass.
min. 150 OC rated
Apply tape/foam
inside recess to stop
silicone leaking underneath.
F
TO REMOVE PRODUCT
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Installation instructions
Final checklist
TO BE COMPLETED BY THE INSTALLER
Is the cooktop earthed?
Check that there is an adequate and constant flow of cool air from the cabinetry to the base of
the cooktop.
Check that the power supply cable is not accessible via cupboard doors or drawers.
Is the cooktop clamped down securely?
Check that the pan detection feature is working correctly. Turn on each cooking zone without
putting any cookware on them. Are all the displays flashing
?
Check that all the cooking zones function correctly. Place suitable pans with water in them on
each zone, then turn all of them on to a high setting. Is the water heating?
Are all touch controls and displays functioning?
To check that the ‘hot surface’ indicators function correctly, turn off all the zones. Is
displayed in all the cooking zone displays?
H
Have you shown the customer how to use the cookop? Make sure you explain to the customer
about:
the importance of taking note of the safety warnings at the beginning of this manual,
especially for persons with cardiac pacemakers or other electrical implants
the ‘hot surface’ indicators (
H)
using induction-suitable cookware only
the pan detection feature ( ).
Installer’s name:
Installer’s signature:
Installation company:
Date of installation:
LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Introduction
Introducing your cooktop
Congratulations on your new purchase. Your Fisher & Paykel induction cooktop is the ultimate in
induction cooking, giving you the speed, precision, and simplicity of electronic control, and the
easy-care elegance of a ceramic glass surface. For more information, visit our local website listed
on the back cover.
A word on induction cooking
Induction cooking is a safe, advanced, efficient, and economical cooking technology. It works by
electromagnetic vibrations generating heat directly in the pan, rather than indirectly through
heating the glass surface. The glass becomes hot only because the pan eventually warms it up.
This technology has a number of advantages over traditional radiant energy cooking:
Heat-up times are much faster.
Use is safer as no heating takes place unless a suitable pan is placed on the cooking zone.
As heat is transferred without loss, you save energy.
Before using your new cooktop
Read this guide, taking special note of the ‘Safety and warnings’ section.
Remove any protective film that may still be on your cooktop.
Using the touch controls
The controls respond to touch, so you don’t need to apply any pressure.
Use the ball of your finger, not its tip.
You will hear a beep each time a touch is registered.
Make sure the controls are always clean, dry, and there is no object (eg a utensil or a cloth)
covering them. Even a thin film of water may make the controls difficult to operate.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Introduction
1
3
2
1
2
3
2
1
Fig.4 CI604DT model
Fig.5 CI754DT model
6
6
1
1400 W (1800W*) zone
1850 W (2500W*) zone
2300 W (3700W*) zone
2300 W (3200W*) zone
2400 W (3700W*) zone
Touch controls
2
3
4
5
6
1
4
2
2
5
* Maximum power output
when set for PowerBoost
See ‘Using your cooktop’s
special features.’
Fig.6 CI905DT model
6
10
7
8
9
11
12
Fig.7 Touch controls for CI604DT and CI754DT models
10
8
11
12
7
9
Fig.8 Touch controls for CI905DT model
10 Heat setting controls
11 Keylock control
12 ON/OFF control
7
8
9
GentleHeat control
Timer control
PowerBoost control
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Choosing the right cookware
Important!
Only use cookware with a base suitable for induction cooking.
Look for the induction symbol on the packaging or the bottom of
the pan.
You can check whether your cookware is suitable by carrying out
a magnet test. Move a magnet towards the base of the pan. If it is
attracted, the pan is suitable for induction.
If you do not have a magnet:
1
2
3
Put some water in the pan you want to check.
Follow the steps under ‘To start cooking’ opposite.
If
does not flash in the display and the water is heating, the pan is suitable.
Cookware made from the following materials is not suitable: pure stainless steel, aluminium or
copper without a magnetic base, glass, wood, porcelain, ceramic, earthenware.
Do not use cookware with jagged edges or a curved base.
Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as
the cooking zone. Always centre your pan on the cooking zone.
Always lift pans off the cooktop– do not slide, or they may scratch the glass.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Using your induction cooktop
To start cooking
1
Touch and hold the ON/OFF
control for 2 seconds.
2
0 will appear in the cooking zone displays.
3
Place a suitable pan on the
cooking zone you wish to use.
Make sure the bottom of the pan
and the surface of the cooking
zone are clean and dry.
4
Select a heat setting by touching
–
or
+
.
If you don’t choose a heat setting within 10
seconds, the cooktop will automatically
turn off. Start with step 1 again.
You can modify the heat setting at any time
during cooking.
If a display flashes
alternately with the heat setting
This means that:
you have not placed a pan on the correct cooking zone or
the pan you’re using is not suitable for induction cooking or
the pan is too small or not properly centred on the cooking zone.
No heating takes place unless there is a suitable pan on the cooking zone.
The cooktop will automatically turn off after 10 minutes if no suitable pan is placed on it.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Using your induction cooktop
When you have finished cooking
OR
1a Turn the cooking zone off by scrolling down to 0 or touching
Make sure the display shows 0.
–
and
+
together.
1b Turn the whole cooktop off by touching the ON/OFF control.
2
Beware of hot surfaces
will show which cooking zone is too hot to touch. It
H
will disappear when the surface has cooled down to a
safe temperature.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Using your induction cooktop
Locking the controls
You can lock the controls to prevent unintended use (for example children accidentally turning
cooking zones on).
When the controls are locked, all controls except the ON/OFF control are disabled.
To lock the controls
1
2
Make sure that the cooktop is turned on but no cooking zone is in use.
Touch and hold the keylock control
indicating that the controls are locked.
for 2 seconds. The red light above the control comes on,
Note: the cooktop will automatically turn off after 10 seconds, but the controls will still be locked
when you turn the cooktop on again.
To unlock the controls
1
2
3
Make sure the cooktop is turned on.
Touch and hold the keylock control
You can now start using your cooktop.
for 2 seconds. The red light above the control goes out.
Important!
Do not lock the controls while a cooking zone is in use. If you do, you can always turn the cooktop off with
the ON/OFF control in an emergency.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Using your cooktop’s special features
Using the PowerBoost feature
This feature enables you to sear meat or bring liquid to the boil very quickly. When a cooking
zone is set for PowerBoost, it uses more than 100% of the power of that particular cooking zone,
resulting in a boost of intense heat.
Important!
PowerBoost heats food and liquids very quickly. Do not leave the cooktop unattended when using this
feature.
To set a cooking zone for PowerBoost
1
With the cooktop turned on, touch the
PowerBoost control . The flashing red
light indicates that PowerBoost is ready
to be set.
2
Within 5 seconds, touch the
of a cooking zone once. Its display will
show
–
or
+
control
P
.
When PowerBoost is set
10 mins
The cooking zone will be on PowerBoost (more than 100%) for 10 minutes, and then
automatically reduce the heat to setting
9
(100%).
To quit the PowerBoost setting
Touch the
zone off.
–
control of the cooking zone at any time and select a new setting or turn the cooking
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Using your cooktop’s special features
Note:
You can set two (CI604DT and CI754DT) or three (CI905DT) cooking zones for PowerBoost, as
long as one is not behind the other. For example:
If you wish to set more than one cooking zone for PowerBoost, you need to set them separately.
When a cooking zone is set for PowerBoost, the cooking zone immediately in front of or behind
it may have to reduce its power level.
Using the GentleHeat feature
This feature is ideal for the most delicate cooking tasks (such as melting chocolate), as the
cooking zone will provide continuous gentle heat (between heat setting levels
0
and 1).
To set a cooking zone for GentleHeat
1
With the cooktop turned on, touch the
GentleHeat control . The flashing red
light indicates that GentleHeat is ready
to be set.
2
Within 5 seconds, touch the
of a cooking zone. Its display will show U...
–
or
+
control
To quit the GentleHeat setting
Touch the
zone off.
+
control of the cooking zone at any time and select a new setting or turn the cooking
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Using your cooktop’s special features
Using the Auto Heat-reduce feature
Cooking zones set for this feature will:
first quickly heat up food or liquid at the highest setting
then automatically reduce the heat to a pre-selected lower setting to cook the food through.
To set a cooking zone for Auto Heat-reduce
1
With the cooktop turned on, touch the
2
Touch
alternately with
+
. The letter
Awill start flashing
–
control of a cooking zone. The display
9
.
will show
9
.
3
Touch
reduce to (
–
briefly and then select the heat setting you want the cooking zone to automatically
).
1
-8
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Using your cooktop’s special features
When Auto Heat-reduce is set
Initially, while the cooking zone is
at the highest setting, A will flash
alternately with your selected lower
setting. The length of time at the
highest setting depends on the lower
heat setting selected. See chart below.
Then, when the period of highest setting
is over, A will stop flashing and the
cooking zone will automatically reduce
the heat to your pre-selected lower
setting.
To increase the lower heat setting while A is flashing, simply touch
+
.
If you would like a lower or higher heat setting than you originally selected, touch
–
and
+
together and set the cooking zone for Auto Heat-reduce again. Alternatively, wait until A stops
flashing and then modify the heat setting.
Pre-selected lower heat setting
Length of time at highest setting
40 seconds
1
2
3
4
5
6
7
8
1 minute
2 minutes
3 minutes
4 minutes
7 minutes
2 minutes
3 minutes
To quit the Auto Heat-reduce setting while
A
is flashing
Touch the
cooking zone together.
–
and
+
controls of the corresponding
Note:
The Auto Heat-reduce and PowerBoost features cannot be used together. If you turn
PowerBoost on when Auto Heat-reduce is already set, the latter will be immediately
cancelled and PowerBoost will be activated instead.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Using your cooktop’s special features
Using the timer
You may use the timer in two different ways:
You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when
the set time is up.
You can set it to turn one or more cooking zones off after the set time is up.
You can set the timer for up to 99 minutes.
Timer overview
Cooking zone indicator
for middle zone
(CI905DT models only)
Minute display
shows the number of minutes
set/remaining for:
Cooking zone
indicators
the cooking zone whose
indicator is flashing
OR
show you which
cooking zone(s) the
timer is set for. In
this illustration, the
timer is set for all
the cooking zones.
the minute minder, if its
indicator is flashing.
If you set different times for
multiple cooking zones, the minute
display will revert to showing the
shortest remaining time (with
the corresponding indicator light
flashing).
You can set or modify
the number of minutes
while this light is on.
A flashing indicator
shows you what
setting is being
shown in the
minute display. In
this illustration, the
remaining time set
for the left front
cooking zone is 31
minutes.
Minute minder indicator
shows if the minute
minder is set. It operates
independently of any
cooking zone.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Using your cooktop’s special features
Using the timer as a minute minder
1
Make sure the cooktop is turned ON.
Note: you can use the minute minder
even if you’re not using any cooking
zones.
2
Touch the
together. The minute minder indicator
will start flashing and 00 will show in the
minute display.
–
and
+
controls of the timer
3
Set the time while the small red light in the
bottom corner of the minute display is on.
Hint: the minutes will scroll faster if you
4
When the time is set, it will begin to count
down immediately. The display will show
the remaining time and the minute minder
indicator will keep flashing.
touch and hold
–
or
+
continuously.
If you are not using any cooking zones
You can use the timer as a minute minder even if you are not using any cooking zones. In this
case, the cooktop will turn itself off 10 seconds after you have set the time, but the time will
continue to count down. To change or cancel the minute minder setting, you will have to turn
the cooktop back on first. See ‘To change or cancel a timer setting’.
When the set time is up
00 will flash and the timer will beep. Touch any control to stop the beeping.
Remember, touching the ON/OFF control will turn the whole cooktop off!
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Using your cooktop’s special features
Setting the timer to turn one or more cooking zones off
1
Make sure the cooking zone(s) you want to
set the timer for are in use.
2
Touch the
–
and
+
controls of the timer
together. Repeat until the indicator of the
desired cooking zone comes on flashing.
Note: only indicators of cooking zones in
use will show as you scroll through.
3
Set the time while the small red light in the bottom corner of the minute display is on.
The timer is now set for the right rear cooking zone.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Using your cooktop’s special features
Setting the timer to turn one or more cooking zones off
You may now continue to set the timer for additional cooking zones:
Touch the and controls of the timer together. Repeat until the indicator of the desired
4
–
+
cooking zone comes on flashing.
Note: the indicator of the cooking zone previously set will be steadily lit, showing you that the
timer is set and counting down for that cooking zone.
5
Set the time while the small red light in the bottom corner of the minute display is on.
You can set different times for each of the cooking zones.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Using your cooktop’s special features
When the timer is set
To check the remaining time for another
cooking zone:
If the timer is set for more than one
cooking zone, only the indicator belonging
to the cooking zone with the shortest
remaining time setting will flash.
Touch the
–
and
+
controls of the timer
together and repeat until the indicator of
the desired cooking zone is flashing.
When the set time is up
The cooking zone whose set time is up will automatically turn off.
00 will flash in the minute display.
The timer will beep.
Touch any control to stop the beeping.
The indicator of the relevant cooking zone will go out.
If the timer is still set and counting down for another cooking zone
The indicator belonging to the cooking zone with the shortest remaining time setting will flash.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Using your cooktop’s special features
To change or cancel a timer setting
1
With the cooktop turned on, touch the
–
and
+
controls of the timer together and repeat until:
the indicator of the desired cooking zone or the minute minder indicator is flashing and
the small red light in the bottom corner of the minute display is on.
2
To change:
2
To cancel:
Set the new time while the small red light OR
at the bottom of the minute display is on.
Touch the
until the minute display shows 00
–
control of the timer and repeat
.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Cooking guidelines
Important!
Take care when frying: oil and fat heat up very quickly, particularly if you’re using PowerBoost. At
extremely high termperatures oil and fat will ignite spontaneously and this presents a serious fire
risk.
Cooking tips
When food comes to the boil, reduce the temperature setting.
Using a lid will reduce cooking times and save energy by retaining the heat.
Minimise the amount of liquid or fat to reduce cooking times.
Start cooking on a high setting and reduce the setting when the food has heated through.
Simmering, cooking rice
Simmering occurs below boiling point, at around 85 OC, when bubbles are just rising occasionally
to the surface of the cooking liquid. It is the key to delicious soups and tender stews because
the flavours develop without overcooking the food. You should also cook egg-based and flour-
thickened sauces below boiling point.
Some tasks, including cooking rice by the absorption method, may require a setting higher than
the lowest setting to ensure the food is cooked properly in the time recommended.
Searing steak
To cook juicy flavoursome steaks:
1
2
3
Stand the meat at room temperature for about 20 minutes before cooking.
Heat up a heavy-based frying pan.
Brush both sides of the steak with oil. Drizzle a small amount of oil into the hot pan and then
lower the meat onto the hot pan.
4
5
Turn the steak only once during cooking. The exact cooking time will depend on the thickness of
the steak and how cooked you want it. Times may vary from about 2 – 8 minutes per side. Press
the steak to gauge how cooked it is – the firmer it feels the more ‘well done’ it will be.
Leave the steak to rest on a warm plate for a few minutes to allow it to relax and become tender
before serving.
For stir-frying
1
2
Choose an induction compatible flat-based wok or a large frying pan.
Have all the ingredients and equipment ready. Stir-frying should be quick. If cooking large
quantities, cook the food in several smaller batches.
Preheat the pan briefly and add two tablespoons of oil.
Cook any meat first, put it aside and keep warm.
3
4
5
Stir-fry the vegetables. When they are hot but still crisp, turn the cooking zone to a lower setting,
return the meat to the pan and add your sauce.
6
7
Stir the ingredients gently to make sure they are heated through.
Serve immediately.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Cooking guidelines
Heat settings
The settings below are guidelines only. The exact setting will depend on several factors,
including your cookware and the amount you are cooking. Experiment with the cooktop to find
the settings that best suit you.
100
80
60
40
20
0
u
1
2
3
4
5
6
7
8
9
P
Heat setting
(A)
Heat setting
Suitability
delicate warming for small amounts of food
melting chocolate, butter, and foods that burn quickly
u
gentle simmering
slow warming
1
-
2
4
reheating
rapid simmering
cooking rice
3
-
pancakes
5
7
-
-
6
8
sautéing
cooking pasta
stir-frying
searing
bringing soup to the boil
9
P
boiling water
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Care and cleaning
What?
How?
Important!
Everyday soiling
on glass
(fingerprints, marks,
stains left by food or
non-sugary spillovers
on the glass)
1
Switch the power to the
When the power to the cooktop
cooktop off at the wall.
Apply cooktop cleaner while
the glass is still warm (but not
hot!)
Rinse and wipe dry with a
clean cloth or paper towel.
Switch the power to the
cooktop back on at the wall.
is switched off, there will be no
‘hot surface’ indication but the
cooking zone may still be hot!
Take extreme care.
Heavy-duty scourers, some nylon
scourers and harsh/abrasive
cleaning agents may scratch the
glass. Always read the label to
check if your cleaner or scourer is
suitable.
2
3
4
Never leave cleaning residue
on the cooktop: the glass may
become stained.
Boilovers, melts, and
hot sugary spills on
the glass
Remove these immediately
with a fish slice, palette knife
or razor blade scraper suitable
for ceramic glass cooktops, but
beware of hot cooking zone
surfaces:
Switch the power to the
cooktop off at the wall.
Hold the blade or utensil at
a 30o angle and scrape the
soiling or spill to a cool area of
the cooktop.
Remove stains left by melts and
sugary food or spillovers as soon
as possible. If left to cool on the
glass, they may be difficult to
remove or even permanently
damage the glass surface.
Cut hazard: when the safety
cover is retracted, the blade in
a scraper is razor-sharp. Use
with extreme care and always
store safely and out of reach of
children.
1
2
3
4
Clean the soiling or spill up
with a dish cloth or paper
towel.
Follow steps 2 to 4 for
‘Everyday soiling on glass’
above.
Spillover on the touch
controls
1
Switch the power to the
cooktop off at the wall.
Soak up the spill
Wipe the touch control area
with a clean damp sponge or
cloth.
Wipe the area completely dry
with a paper towel.
Switch the power to the
cooktop back on at the wall.
The cooktop may beep and turn
itself off, and the touch controls
may not function while there is
liquid on them. Make sure you
wipe the touch control area dry
before turning the cooktop back
on.
2
3
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Troubleshooting
Troubleshooting chart
Problem
Possible causes
What to do
The cooktop cannot be
turned on.
No power.
Make sure the cooktop is
connected to the power supply
and that it is switched on at the
wall. Check whether there is
a power outage in your home
or area. If you’ve checked
everything and the problem
persists, call your Authorised
Service Centre or Customer
Care.
The touch controls are
unresponsive.
The controls are locked.
Unlock the controls. See section
‘Using your induction cooktop’
for instructions.
The touch controls are
difficult to operate.
There may be a slight film of water Make sure the touch control
over the controls or you may be
using the tip of your finger when
touching the controls.
area is dry and use the ball of
your finger when touching the
controls.
The glass is being
scratched.
Rough-edged cookware.
Use cookware with flat and
smooth bases. See ‘Choosing
the right cookware’.
Unsuitable, abrasive scourer or
cleaning products being used.
See ‘Care and cleaning’.
Some or all displays flash Liquid has spilled onto the touch
Switch the power to the
cooktop off at the wall and
see ‘Care and cleaning’ for
instructions.
and there is a
control area.
continuous beep.
There are objects (eg utensils) on
the touch control area.
Remove the objects from the
touch control area.
Several touch controls are
registering continuous contact
(eg due to someone resting their
hand or arm on the touch control
area).
Remove the cause of
continuous contact.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Troubleshooting
Troubleshooting chart
Problem
Possible causes
What to do
Some pans make
crackling or clicking
noises.
This may be caused by the
construction of your cookware
(layers of different metals
vibrating differently).
This is normal for induction
cookware and does not indicate
a fault.
The cooktop makes a low This is caused by the technology
This is normal, but the
noise should quieten down
or disappear completely
when you decrease the
heat setting.
humming noise when
used on a high heat
setting (especially
PowerBoost).
of induction cooking.
Fan noise coming from
the cooktop.
A cooling fan built into
your cooktop has come on
to prevent the electronics
from overheating. It may
continue to run even after
you’ve turned the cooktop
off.
This is normal and needs
no action. Do not switch
the power to the cooktop
off at the wall while the
fan is running.
Pans do not become hot
The cooktop cannot detect the
pan because it is not suitable for
induction cooking.
Use cookware suitable for
induction cooking. See
section ‘Choosing the right
cookware’.
and
appears in the
display.
The cooktop cannot detect the
pan because it is too small for
the cooking zone or not
Centre the pan and make
sure that its base matches
the size of the cooking
zone.
properly centred on it.
PowerBoost is temporarily
unavailable because the
cooktop needs to protect
itself from overheating.
Allow the cooktop to cool
down.
P flashes in the display
when you are tyring to
set PowerBoost.
The cooktop or a cooking Technical fault.
zone has turned itself off
unexpectedly, a tone
sounds and an error code
is displayed (typically
E or Er alternating with
one or two digits in the
Please note down the error
letters and numbers, switch
the power to the cooktop off
at the wall, and contact your
Authorised Service Centre or
Customer Care with the
error code information.
cooking zone displays).
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Warranty and service
Before you call for service or assistance ...
Check the things you can do yourself. Refer to the installation instructions and your user guide
and check that:
1
2
your product is correctly installed
you are familiar with its normal operation.
If after checking these points you still need assistance, please refer to the Service & Warranty
book for warranty details and your nearest Authorised Service Centre, or contact us through our
local website listed on the back cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Warranty and service
This cooktop has been designed and constructed in accordance with the following
codes and specifications:
In New Zealand and Australia:
AS/NZS 60335-1 General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NZS 1044 Electromagnetic Compatibility Requirements.
In Europe:
Safety requirements of EEC Directive “Low voltage” 2006/95:
- EN 60335-1 General Requirements for Domestic electrical appliances
- EN 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
Safety requirements of EEC Directive “EMC” 2004/108:
- EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 Electromagnetic Compatibility
Requirements
Requirements of EEC Directive 93/68.
European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE)
(for European Union countries only)
GB This appliance is marked according to the European directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product.
The symbol
on the product, or on the documents accompanying the product, indicates that
this appliance may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. Disposal
must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this product, please
contact your local city office, your household waste disposal service or the shop where you
purchased the product.
Product details
Fisher & Paykel Ltd
Model
Serial No.
Purchaser
Suburb
Date of Purchase
Dealer
Town
Country
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright © Fisher & Paykel 2011. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ AU GB IE
F&P PN - 599569 E F&P ITALY PN 1103222-ß5
12.2011
Download from Www.Somanuals.com. All Manuals Search And Download.
|