User’s Manual
CSVEQ 100 D
Composite Video and S-Video Line Driver
with Audio
Extron USA - West Extron USA-East Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Dubai
Headquarters
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
Inside China Only
+800.633.9876
68-1598-01 Rev. A
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
08 08
+1.714.491.1500
+1.714.491.1517 FAX
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该设备只能使用产品上标明的电源。 设备
必须使用有地线的供电系统供电。 第三条线
（地线）是安全设施，不能不用或跳过。
有重要的操作和维护说明。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
注意
阅读说明书 • 用户使用该设备前必须阅读并理
解所有安全和使用说明。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
保存说明书 • 用户应保存安全说明书以备将来使
用。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — CSVEQ 100 D
Installation and service must be performed by authorized
personnel only. These line drivers must be used with UL
approved, grounded electrical boxes.
C
To install and set up the line driver, follow these steps and see the
appropriate sections of this manual for details.
Step 1
Turn the input and output devices off and unplug their power cords.
Verify that the line driver is disconnected from the power source
before proceeding.
Step 2
Attach output cables to the rear panel of the line driver and to the
output devices. See "Rear Panel Features and Operation" in chapter 3
for details.
Step 3
Attach input cables from the input devices to the line driver’s front
panel input connectors. See "Front Panel Features and Operation" in
chapter 3.
Step 4
Connect power cords and turn on the output devices (projector/
monitor, speakers) and input devices.
Step 5
The picture should appear and sound should be audible. If not,
ensure that all devices are plugged in and receiving power. Check
the cabling, make adjustments as needed. For further details, see
"Testing and troubleshooting" in chapter 2.
Step 6
While watching the display, adjust the video gain and
equalization by using the rotary gain and equalization (EQ) control
potentiometers. An oscilloscope can be used to achieve a more
precise adjustment. See “Gain adjustment control" and "Equalization
(EQ) adjustment control” in chapter 3 for details.
Make all adjustments using an Extron Tweeker or small screwdriver.
If using very short output cables, set all potentiometers to the default
setting (the arrow on the control pointing to the dot beside it).
CSVEQ 100 D • Quick Start Guide
QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start — CSVEQ 100 D, cont’d
When using long cables, follow these steps:
a. Supply the color bars test signal to the input. (Recommendation:
use an Extron VTG 300 Video Test Generator to generate the test
signal.)
b. Adjust the Gain control(s) for the output until the signal level
at the far end is the same as the input (or the display shows the
correct brightness and contrast).
c. Adjust the EQ control for the output so that no overshoot or
round front corner appears at the far end on the oscilloscope or
you see a sharp picture with no smearing.
Step 7
See "Installation Instructions" in chapter 2 for further installation
details.
CSVEQ 100 D • Quick Start Guide
QS-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Features ........................................................................................ 1-2
Accessories ........................................................................................A-1
All trademarks mentioned in this manual are the properties of their respective owners.
68-1598-01 Rev. A
08 08
CSVEQ 100 D • Table of Contents
TOC-i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
CSVEQ 100 D • Table of Contents
TOC-ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
The CSVEQ 100 D is a high performance composite video,
S-video, and audio line driver designed to compensate for signal
attenuation and high frequency loss encountered during long
cable runs. It is capable of simultaneously driving composite
video and S-video plus audio signals up to 1000 feet (300 m)
on Extron MHR or RG59 high resolution video cables and STP
series audio cables. The CSVEQ 100 D mounts in a Decora®
style wallplate and is ideal for use in residential and commercial
environments where video and audio signals need to be
extended over a long distance.
Features
Long distance line driving — Drives composite video or
S-video signals up to 1000 feet (300 meters) using Extron's
MHR cable.
Balanced or unbalanced stereo or dual mono output —
Unbalanced stereo audio input can be output as balanced
or unbalanced stereo audio or as dual mono.
Video gain adjustment — Offers a video gain adjustment for
composite video and Y of S-video with a range of
-1 dB to +3 dB, and C of S-video with a range of 0 dB to
+10 dB.
Equalization adjustment — Features an equalization
adjustment range of 0 dB to +7 dB at 5 MHz that changes
the level and peaking of the output signal to compensate
for use of long cables.
Stereo or dual mono output jumper — A rear panel jumper
selects between stereo and dual mono output formats.
Front panel LED indicator — Indicates when the line driver is
receiving power or a video signal.
Compatibility — Compatible with NTSC, PAL, and SECAM
CSVEQ 100 D • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Application Example
To get started, refer to the "Quick Start Guide" at the beginning
of this manual.
Installation and service must be performed by
authorized personnel only.
C
Extron
MPA 122
Mini Power
Ampliꢀer
Extron
SI 26X
Two-way Ceiling
Speakers
Balanced
Audio
S-Video
Extron
CSVEQ 100 D
Projector
Composite Video, S-Video,
and Audio Line Driver
Composite
Video
S-VIDEO IN
VIDEO IN
1,000 Feet
R
-
AUDIO IN
L
DVD/VCR
Combo
CSVEQ 100 D application example
CSVEQ 100 D • Installation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the CSVEQ 100 D
The CSVEQ 100 D is a wall-mounted product and can be
mounted into an electrical wall box. This section includes site
preparation, wall box installation, and the mounting of the line
driver in the wall box.
The line driver must be installed into an Underwriters
Laboratories (UL) approved electrical wall box. The
box is not included with the line driver; the installer is
responsible for obtaining and installing the box.
N
Preparing the site and installing the wall box
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. You
may need to install the cables into the wall or conduits before
installing the line driver.
The line driver can be installed in a standard one-gang electrical
wall box. The installation must conform to national and local
electrical codes. A dimensional drawing and a cutout template
of the line driver are provided in appendix B of this manual.
The cutout template shown in appendix B is not full size.
Pay attention to the measurements shown on the template.
N
1.
Mark the guidelines for the opening on the wall.
•
If the line driver is to be installed in a wall box, place
the box against the installation surface and draw a line
on it around the outside of the box.
•
If the line driver is to be installed without a wall box
(fastening it directly to the wall), measure and mark
the surface for the cutout area indicated in the cutout
template.
2.
3.
Cut out the material from the marked area.
Check the opening size by inserting the wall box (if used)
or the line driver (if no box is used) into the opening. The
box and line driver should fit easily into the opening.
Enlarge or smooth the edges of the opening if needed.
4.
5.
Feed cables through the wall box punch-out holes, and
secure them with cable clamps to provide strain relief.
Insert the wall box into the opening, and attach it to the
wall or stud using nails or screws. The front edge should
be flush with the outer wall surface. See the following
illustration.
CSVEQ 100 D • Installation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Wall Stud
Wall Stud
e
Installation Cable
Cable Clamp
lamp
Nails
Screws or Nails
Attaching the wall box to a wall stud
If attaching the wall box to wood, use four #8 or #10
screws or 10-penny nails. A minimum of ½" (1.3 cm) of
screw threads must penetrate the wood.
If attaching the wall box to metal studs, use four #8 or
#10 self-tapping sheet metal screws or machine bolts with
matching nuts.
Mounting the line driver
Before mounting the line driver and if it has not already been
tested, test the system to make sure that the connections and
settings are correct. See "Testing and troubleshooting" in this
chapter.
If the system is operating correctly, the line driver can be
installed in the wall. Adjust the gain and equalization, and set
the Audio Out switch to Stereo or Dual Mono before fastening
the line driver into the wall box. The controls and cables will
be inaccessible after installation. See “Rear Panel Features
and Operation" in chapter 3 for details about settings and
adjustments.
Continue mounting the line driver by following the steps below.
1.
Remove power from the line driver by disconnecting the
power supply from the AC source.
2.
3.
Connect the output cables to the rear of the device.
Place the line driver through the opening in the wall and
into the wall box. Take care not to damage the output
cable(s), which fit behind the line driver at the back of the
wall box.
CSVEQ 100 D • Installation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
Mount the line driver to the wall box with machine screws
as shown in the following illustration.
Wall Box
Extron
CSVEQ 100 D
S-VIDEO
IN
VIDEO IN
Wall opening
R
AUDIO IN
L
is flush with
edge of box.
Decora
Faceplate
Mounting the line driver to a wall box
5.
6.
Attach the Decora® wall plate to the line driver as shown in
the illustration above.
Reconnect the power supply, connect input cables to the
line driver, and restore power to the equipment.
Installing the mud ring bracket
The CSVEQ 100 D can also be installed using the included mud
ring bracket. See the illustration below.
1.
Once the proper wall location for mounting the line driver
has been determined, cut an opening in the wall using the
proper mounting template found in the appendix.
2.
3.
Carefully cut away the mounting surface material inside
the traced template lines
Test the fit of the mud ring. The doglegs should fit easily
into the hole and the flat portion should rest flush against
the wall. See the note in the following illustration.
4.
Rotate all doglegs inward.
CSVEQ 100 D • Installation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
5.
6.
Insert the mud ring into the hole.
Tighten all of the dogleg screws until the doglegs clamp
the mud ring to the mounting surface. Do not overtighten.
Standard mud rings only: If you are going to screw the
mud ring to the surface, rather than using the detachable
doglegs, mark the four surface mounting screw holes at the
corners of the mud ring.
Wall
Extron
Wall Mounting Bracket
Extron
CSVEQ 100 D
S-VIDEO
IN
N
VIDEO
I
R
AUDIO IN
L
Decora
Faceplate
Installation using a mud ring
CSVEQ 100 D • Installation
2-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Testing and troubleshooting
1.
Apply power to the line driver. The power/signal LED on
the line driver lights amber (power) or green (video input).
2.
If the LED does not light, check the wiring at both the line
driver and the power supply, and make sure the power
supply is connected to a power source.
If the image does not appear or there is no sound
1.
2.
Make sure that all the devices are powered on.
Ensure that the connectors are wired correctly at both
ends of the cables. Audio cables must be wired for an
unbalanced stereo input signal and for the appropriate
(unbalanced or balanced) output signal.
3.
4.
Check the video source’s user’s guide or contact Extron to
determine if there are special requirements to output video
to the external video port.
Call the Extron S3 Sales and Technical Support Hotline if
the image still does not appear or there is no sound.
If the image is not displayed correctly
1.
If the picture is too bright or too dark, or if the edges of the
image seem to exceed their boundaries, or if thin lines and
sharp edges look thick and fuzzy, change the gain setting.
If the picture appears and is stable, but it has ghosting
or blooming, verify that the video input is properly
terminated. If the problem is not resolved by changing the
termination, try using a different input cable. Poor quality
or damaged cable can cause ghosting and blooming.
2.
If the picture still is not displayed correctly, call the Extron
S3 Sales and Technical Support Hotline.
CSVEQ 100 D • Installation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
CSVEQ 100 D • Installation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Front Panel Features and Operation
Wall Plate
Faceplate
1
S-VIDEO
IN
VIDEO IN
3
4
2
AUDIO IN
L
R
Wall Plate
Mounting Screw
CSVEQ 100 D
Front Panel
Power indicator LED — This LED lights:
a
• Amber when the line driver is receiving full power
• Green when the line driver is receiving a video signal
Video input connector — Connect a composite video input
source to this RCA connector.
b
c
S-video input connector — Connect an S-video input source to
this 4-pin mini DIN connector. See the following pinout table.
3
4
1
2
S-video Pinout Table
NAME DESCRIPTION
PIN
1
GND
GND
Y
Ground (Y)
Ground (C)
Luminance
Chrominance
2
3
4
C
CSVEQ 100 D • Operation
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio input connectors — Connect an unbalanced stereo audio
source to these left (L) and right (R) RCA connectors. Wire the
male connector as shown in the following illustration.
d
Tip (+)
Sleeve (
)
CSVEQ 100 D • Operation
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
Rear Panel Features and Operation
CSVEQ 100 D
5
6
7
8
9
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
4
AUDIO OUTPUT
3
1
2
CSVEQ 100 D Rear Panel
Power connector — Connect the external 12 VDC power supply
into this 2-pin, 3.5 mm direct insertion connector. The power
supply is included with the unit. The "Power supply wiring"
section in this chapter explains how to wire the connector.
a
b
Audio output connector — Wire a balanced/unbalanced audio
output device to this 3.5 mm, 5-pole, direct insertion captive
screw connector. See the following wiring diagrams.
CSVEQ 100 D • Operation
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Balanced Stereo
Unbalanced Stereo
Left Tip (+)
Left Tip (+)
Left Ring (-)
Sleeve (s)
Right Tip (+)
Right Ring (-)
Sleeve
Right Tip (+)
AUDIO
OUTPUT
CONFIG
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
Set Audio Output jumper to Stereo.
Set Audio Output jumper to Stereo.
Balanced Mono
Unbalanced Mono
Use either the left or the right channel.
Use either the left or the right channel.
Tip (+)
Ring (-)
Sleeve
Tip (+)
Sleeve
AUDIO
OUTPUT
CONFIG
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
JUMPER POSITION
OFF = DUAL MONO
ON = STEREO
Set Audio Output jumper to Dual Mono.
Set Audio Output jumper to Dual Mono.
CAUTION Connect the sleeve to ground
(Gnd). Connecting the sleeve to
a negative (–) terminal will
damage the audio output
circuits.
Do not tin the wires!
Balanced audio is more resistant to noise and can be driven
for longer distances than unbalanced audio. For best
results, wire the output for balanced audio.
N
Video output connector (green cable) — Connect a composite
video output device to the BNC connector.
c
S-video Y connector (luma, white cable) — Connect the luma of
an S-video output device to the BNC connector.
S-video C connector (chroma, yellow cable) — Connect the
chroma of an S-video output device to the BNC connector.
Audio output jumper — Set this jumper to select either stereo
(jumper on) or dual mono (jumper off) output.
d
e
When set for dual mono, the left and right channels output the
same signal (either channel or both channels can be used). The
audio output can be wired for balanced/unbalanced mono or
stereo output. The wiring and the jumper setting must match.
Output gain potentiometer (chroma) — Use a small
screwdriver to rotate this potentiometer to adjust the chroma
gain when the line driver is connected to long output cables.
The adjustment range is 0 dB to +10 dB. The default is unity
(the dot position). See "Gain adjustment control" in this chapter.
CSVEQ 100 D • Operation
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
Output equalization (EQ) potentiometer (luma) — Use a
f
small screwdriver to rotate this control to adjust equalization
when the line driver is connected to long output cables. The
adjustment range is 0 dB to +7 dB. The default is set to 0 dB (the
dot position). See "Equalization (EQ) adjustment control" in this
chapter.
Output gain potentiometer (luma) — Use a small screwdriver
to rotate this potentiometer to adjust the luminance gain
when the line driver is connected to long output cables. The
adjustment range is -1 dB to +3 dB. The default is unity (the dot
position). See "Gain adjustment control" in this chapter.
g
h
i
Output gain potentiometer (video) — Use a small screwdriver
to rotate this control to adjust the gain when the line driver is
connected to long output cables. The adjustment range is -1
dB to +3 dB. The default is unity (the dot position). See "Gain
adjustment control" in this chapter.
Output equalization (EQ) potentiometer (video) — Use a
small screwdriver to rotate this control to adjust equalization
when the line driver is connected to long output cables. The
adjustment range is 0 dB to +7 dB. The default is set to 0 dB (the
dot position). See "Equalization (EQ) adjustment control" in this
chapter.
Power supply wiring
Wire the line driver's power connector as shown below.
Smooth
Ridges
3
A
A
5
SECTION A–A
Power Supply
Output Cord
Captive Screw
Connector
Power connector wiring
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply and the
line driver. Identify the power cord negative lead by
the ridges on the side of the cord.
C
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
CSVEQ 100 D • Operation
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
The two power cord wires must be kept separate while
the power supply is plugged in. Remove the power
before wiring.
W
Do not tin the power supply leads before installing in the
direct insertion connector. Tinned wires are not as secure
in the connectors and could be pulled out.
N
Gain adjustment control
The gain control adjusts picture brightness by compensating
for signal amplitude loss caused by cable resistance. To adjust
the output gain, view the display while using a small, flat-blade
screwdriver to rotate the potentiometer. This control produces
a gain adjustment ranging from -1 dB to + 3 dB (video and luma
of S-video) and from 0 dB to +10 dB (chroma of S-video). Select
the setting that gives the best picture brightness.
The gain control is a potentiometer with a mechanical stop
at the high and the low end. After you have reached the
high or low end of the adjustment, no change is apparent
on the display. The default is unity (the dot position)
N
You can judge the adjustment visually by viewing the display.
For a more precise setting use an oscilloscope or a waveform
monitor connected to the far end of the output cable, and adjust
the gain so that the level at the waveform monitor is 100 IRE.
Equalization (EQ) adjustment control
The equalization control adjusts the output level and peaking
to get a sharp picture. This adjustment changes the level and
peaking of the output signal to compensate for capacitance
caused by up to 1000 feet (300 meters) of Extron MHR cable.
This control produces an equalization adjustment ranging from
0 dB to + 7 dB (video and luma of S-video).
CSVEQ 100 D • Operation
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
Use a small, flat-blade screwdriver to rotate this control. View
the display and select the setting that gives the sharpest picture.
For a more precise setting, you can use an oscilloscope or a
waveform monitor connected to the far end of the output
cable, and adjust the equalization so that the color burst ranges
between -20 IRE and +20 IRE.
The EQ control is a potentiometer with a mechanical stop
at the high and the low end. After you have reached the
high or low end of the adjustment, no change is apparent
on the display. The default is set to 0 dB (the dot position).
N
Replacing the Decora Faceplate
The front faceplate is replaced by removing the two rear panel
mounting screws, replacing the faceplate, then reattaching the
two screws, as shown in the CSVEQ 100 D example below.
CSVEQ 100 D
AUDIO
OUTPUT
CONFIG
JUMPER POSITION
OFF
ON
=
DUAL MONO
=
STEREO
AUDIO OUTPUT
Mounting
Screws
Faceplate (rear)
Removing the CSVEQ 100 D faceplate
CSVEQ 100 D • Operation
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
Specifications
Video
Gain................................................. Composite video and Y of S-video:
-1 dB to +3 dB (x0.9 to x1.4), adjustable
C of S-video: 0 dB to +10 dB (x1 to x3),
adjustable
Equalization................................... 0 dB to +7 dB (x1 to x2) at 5 MHz,
adjustable
Bandwidth (Y of S-video)............. 185 MHz (-3 dB)
Output cable driving distance..... Up to 1000' (300 m) with Extron MHR
cable
Video input
Number/signal type..................... 1 S-video, 1 composite video
Connectors ..................................... 1 female 4-pin mini DIN, 1 female RCA
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite
video (including sync)
0.3 Vp-p for C of S-video
Minimum/maximum levels........ 0.4 to 2.0 Vp-p with no offset at unity gain
for composite video (including sync) or
for Y of S-video
Impedance...................................... 75 ohms
Return loss...................................... <-25 dB @ 0 to 5 MHz
DC offset (max. allowable)........... 4.0 V
Input coupling............................... AC
Video output
Number/signal type..................... 1 composite video, 1 S-video
Connectors ..................................... 3 female BNC attached via 4" pigtails
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite
video (including sync)
0.3 Vp-p for C of S-video
Minimum/maximum levels........ 0.4 to 2.0 Vp-p (follows input)
Impedance...................................... 75 ohms
Return loss...................................... -30 dB @ 5 MHz
DC offset......................................... ±5 mV with no input signal
Floating: +0.1 to -0.6 V, depending on
input signal content
CSVEQ 100 D • Specifications and Parts
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Sync
Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio
Gain................................................. Unbalanced output: 0 dB; balanced output:
+6 dB
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB
THD + Noise.................................. 0.03% @ 1 kHz at nominal level
S/N.................................................. >90 dB at maximum output (unweighted)
Stereo channel separation ............ >80 dB @ 1 kHz
Output cable driving distance..... Up to 1000' (300 m) with Extron STP cable
Audio input
Number/signal type..................... 1 stereo unbalanced
Connectors ..................................... 2 female RCA
Impedance...................................... 18k ohms unbalanced, DC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level.............................. +8 dBV, unbalanced at 1% THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
N
Audio output
Number/signal type..................... 1 stereo or dual mono (jumper-selectable),
balanced/unbalanced
Connectors ..................................... (1) 3.5 mm direct insertion captive screw
connector, 5 pole
Impedance...................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ....................................... ±0.5 dB channel to channel
Nominal level ................................ -10 dBV, unbalanced; -2 dBu, balanced
Maximum level ............................. +9 dBV, unbalanced; +17 dBu, balanced at
1% THD+N with a 10k ohm load
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 2 A, regulated
Power input requirements........... 12 VDC, 0.2 A
CSVEQ 100 D • Specifications and Parts
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Cooling ........................................... Convection, no vents
Mounting........................................ Wall or furniture mountable with standard
US electrical wall boxes or mud rings
Enclosure........................................ Metal rear enclosure, plastic faceplate
Enclosure dimensions
Faceplate............................. 2.6" H x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora®
faceplate. *Height is 3.8" [9.5 cm],
including mounting tabs.)
(Depth excludes connectors.)
Device ................................. 2.7" H x 1.8" W x 0.75" D
(6.9 cm H x 4.6 cm W x 1.9 cm D)
(Depth excludes connectors; height
excludes mounting tabs.)
Product weight .............................. 0.2 lbs (0.1 kg)
Shipping weight ............................ 2 lbs (1 kg)
Vibration......................................... ISTA 1A in carton (International Safe
Transit Association)
Listings............................................ UL, CUL
Regulatory compliance
Safety................................... CE, C-tick, CUL, UL
EMI/EMC .......................... CE, C-tick, FCC Class A, ICES, VCCI
MTBF............................................... 30,000 hours
Warranty......................................... 3 years parts and labor
All nominal levels are at 10%.
N
N
Specifications are subject to change without notice.
CSVEQ 100 D • Specifications and Parts
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Included Parts
These items are included in each order of the CSVEQ 100 D.
Included parts
Replacement
part number
CSVEQ 100 D (black, white)
60-951-02, -03
Faceplate, black (included
with 60-951-02 only)
21-xxx-0xLF
Faceplate, white (included
with 60-951-03 only)
21-xxx--0xLF
Decora® wall plate, black
included with 60-951-02
only)
Decora® wall plate, white
(included with 60-951-03
only)
One-gang Decora® mud ring
70-581-12
12 VDC, 2 A external power
supply
28-181-01LF
IEC power cord
User’s manual
Optional Accessories
These items are optional accessories for the CSVEQ 100 D.
Accessory
Part number
MHR-2 mini high resolution non-plenum
cable, bulk
22-123-xx
22-129-xx
22-145-xx
22-146-xx
22-098-xx
22-164-xx
MHR-2P mini high resolution plenum
cable, bulk
RG59 high resolution non-plenum cable,
bulk
RG59P high resolution plenum cable,
bulk
RG6 super high resolution non-plenum
cable, bulk
RG6P super high resolution plenum
cable, bulk
CSVEQ 100 D • Specifications and Parts
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Accessory
Part number
MHR-2 SV mini high resolution S-video
cables
26-316-xx
AV RCA cable
STP cable
IN8906, IN8920
Various
CSVEQ 100 D • Specifications and Parts
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Template
CSVEQ 100 D Dimensions
Dimensions are shown in inches [mm}.
0.06” (0.15 cm)
0.46” (1.55 cm)
0.10” (0.25 cm)
2.83” (7.19 cm)
0.00” (0.00 cm)
2.72” (6.91 cm)
1.92” (4.86 cm)
0.92” (2.32 cm)
0.11” (0.28 cm)
0.00” (0.00 cm)
2.74” (6.96 cm)
Front View
Side View
CSVEQ 100 D • Dimensions and Template
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Cut-out Template
Always check and go by the dimensions given in this
appendix. The template is not full size.
N
Cut-Out Template for the Extron
CSVEQ 100 D
2.79"
(7.09 cm)
Wall Plate
1.75"
(4.5 cm)
Location of Line Driver
2.8"
4.50"
(7.1 cm)
(11.43 cm)
SURFACE
CUT-OUT AREA
FOR
To install
FURNITURE
MOUNT
line driver
directly into
furniture or wall,
cut along this line.
TEMPLATE IS NOT FULL SIZE
CSVEQ 100 D • Dimensions and Template
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Template, cont’d
CSVEQ 100 D • Specifications and Parts
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
CSVEQ 100 D • Specifications and Parts
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Template, cont’d
CSVEQ 100 D • Specifications and Parts
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|