User’s Manual
P/2 DA2 WM/EC and AAP models
Distribution Amplifier
68-463-01
Printed in the USA
Extron Electronics, Europe
Extron Electronics, Asia
Extron Electronics Information
Extron Electronics, USA
™
Beeldschermweg 6C, 3821 AH Amersfoort 135 Joo Seng Rd. #04-01, PM Industrial Bldg.
+31.33.453.4040 FAX +31.33.453.4050 +65.383.4400 FAX +65.383.4664
1230 South Lewis Street, Anaheim, CA 92805
800.633.9876 714.491.1500 FAX 714.491.1517
USA
™
ExtronFAX
:
714.491.0192
The Netherlands
Singapore 368363
24-hour access—worldwide!
Download from Www.Somanuals.com. All Manuals Search And Download.
Ta b le o f Co n t e n t s
Ch a p t e r 1 • In t ro d u ct io n ......................................................... 1-1
Ab o u t t h e P/2 DA2 WM/EC a n d
P/2 DA2 WM/EC AAP ............................................................. 1-2
Fe a t u re s ...................................................................................... 1-2
Ch a p t e r 2 • Co n t ro ls a n d In st a lla t io n ........................... 2-1
Fro n t a n d Re a r Pa n e ls ................................................. 2-2
Front faceplate ...................................................................... 2-2
Rear connectors ..................................................................... 2-3
In st a llin g t h e P/2 DA2 WM/EC ................................... 2-4
Easy setup procedure ............................................................ 2-4
Installing the mounting bracket ........................................... 2-5
Cabling ................................................................................... 2-6
Connecting audio output ...................................................... 2-7
Installing Architectural Adapter Plates ................................ 2-9
P/2 DA2 WM wallmount installation .................................. 2-10
P/2 DA2 EC Euro Channel installation ................................ 2-11
Setting the DIP switches ...................................................... 2-11
Ap p e n d ix ........................................................................................... A-1
Sp e cifica t io n s ......................................................................... A-2
P/2 DA2 WM Fa ce p la t e Dim e n sio n s ............................. A-4
Ca b le s ......................................................................................... A-6
Op t io n a l Arch it e ct u ra l Ad a p t e r Pla t e s ...................... A-7
P/2 DA2 WM Mo u n t in g Te m p la t e ............................... A-11
P/2 DA2 WM AAP Mo u n t in g Te m p la t e ..................... A-12
68-463-01 C
Printed in the USA
09-00
P/2 DA2 WM/EC Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
P/2 DA2 WM/EC
Chapter One
1
In t ro d u ct io n
About the P/2 DA2 WM/EC and P/2 DA2 WM/EC AAP
Features
P/2 DA2 WM/EC
Download from Www.Somanuals.com. All Manuals Search And Download.
In t ro d u ct io n
Ab o u t t h e P/2 DA2 WM/EC a n d P/2 DA2
WM/EC AAP
P/2 DA2 WM/EC
The P/ 2 DA2 WM/ EC and P/ 2 DA2 WM/ EC AAP are a one
input, two output, high resolution VGA/ XGA distribution
amplifier with audio. With a video bandwidth of 300 MHz, this
distribution amplifier is compatible with VGA, SVGA, VESA,
XGA, and SXGA graphics cards, monitors, projectors, and LCD
panels.
For audio, the P/ 2 DA2 WM/ EC features a 3.5 mm female jack
for input and a 3.5 mm captive screw connector for balanced or
unbalanced output.
The P/ 2 DA2 WM is the wallmount version and the P/ 2 DA2
EC is the Euro Channel version. The P/ 2 DA2 WM AAP and
the P/ 2 DA2 EC AAP are the same base products, but with
AAP faceplates added. These plates are a convenient method of
providing various connectors for most audio and video
applications.
Fe a t u re s
2-color power/signal LED — When the interface is On, the
power/ signal LED will light amber. When the
interface is On and a signal is present, the LED will
light green.
Chapter Tw o
2
Gain/peak control— Compensates for signal degradation
caused by long cable lengths.
Stereo audio — Front panel audio input jack and a 3.5 mm
captive screw output connector on the rear panel.
Buffered local monitor output — 15-pin HD female
Co n t ro ls a n d In st a lla t io n
connector
Computer video input — 15-pin HD female connector
Front and Rear Panels
Wall mountable (WM model) — Self-contained enclosure
provides for convenient wall mounting.
Installing the P/2 DA2 WM/EC
Euro Channel mountable (EC model) — This model
mounts easily in the Euro Channel raceway
Optional Architectural Adapter Plates — The P/ 2 DA2
WM may be user-configured with up to 4
Architectural Adapter Plates (3 for the EC version).
These adapter plates provide a selection of pass-
through signal connectors for various audio and
video requirements.
1-2
P/2 DA2 WM/EC Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n
Unity – output signal level is same as that of input
with no added peaking
Fro n t a n d Re a r Pa n e ls
Fro n t fa ce p la t e
50% – increases the output signal level and adds
50% of the maximum peaking to the signal
If the edges of the image seem to exceed their
boundaries, or if thin lines and sharp edges look
thick and fuzzy, try changing the level/peak setting.
1
AUTO POWER
1
2
P/2 DA2 EC
AUTO POWER
2
GAIN/
PEAKING
100%
ID PINS
UNITY
5
6
50%
5
6
GAIN/PEAKING
4
3
4
Fig u re 2-2 — P/2 DA2 EC fa ce p la t e fe a t u re s
3
Fig u re 2-1 — P/2 DA2 WM fa ce p la t e fe a t u re s
Re a r co n n e ct o rs
1
2
Both WM and EC models have the same front and
rear panel connectors and features. See figure 2-2.
2-color power/signal LED — lights amber to indicate
power On only; lights green to indicate power On
with video signal present.
1
NC
12-24V AC/DC
L
R
Audio input jack — 3.5 mm stereo input
2
3
NC
VGA input connector — HD 15-pin male analog
12-24V AC/DC
L
R
video input connector
3
Buffered local monitor output — HD 15-pin female
for output to a local monitor
4
5
Fig u re 2-3 — P/2 DA2 WM re a r co n n e ct o rs
ID bit termination DIP switches — provides proper
ID bit termination for a laptop computer that is not
attached to a local monitor.
Power input — 12 - 24 VAC or DC (captive screw
connector). The center pole contains no conductor.
Connect the conductors to the outer two poles only.
1
3-position gain/peaking switch — compensates for
cable capacitance and resistance due to long cable
runs; position switch for best image on the output
display device.
6
Positive
N/C
Negative
Audio output — 3.5 mm captive screw stereo output
2
3
100% – increases the output signal level and adds
100% of the maximum peaking to the signal
VGA output — HD 15-pin female analog video
output connector
2-2
P/2 DA2 WM/EC Controls and Installation
2-3
P/2 DA2 WM/EC Controls and Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n , co n t ’d
“Euro Channel installation” section.
In st a llin g t h e P/2 DA2 WM/EC
6
7
Power up all of the input and output devices.
Ea sy se t u p p ro ce d u re
The image should now display on screen. If it does
not, double check steps 3 through 6 and make
adjustments as needed. Refer to the section “Setting
the DIP switches” in this chapter.
The wall-mounted P/ 2 DA2 WM kit consists of the
faceplate/ distribution amplifier assembly and a mounting
bracket which mounts in a wall opening and to which the
faceplate assembly is attached. The P/ 2 DA2 EC kit
consists of the faceplate/ distribution amplifier assembly
which mounts in the Euro Channel raceway.
For the P/ 2 DA2 WM, attach the P/ 2 DA2 WM to the
wall mounting bracket (see “P/2 DA2 WM wall
installation”).
8
For wall mounting only: Using the mounting
template provided in the “Appendix” as a guide,
carefully cut a mounting hole through the wall where
the mounting bracket is to be installed.
1
2
3
4
For the P/ 2 DA2 EC, attach the P/ 2 DA2 EC to the
Euro Channel (see “P/2 DA2 EC Euro Channel
installation”).
For wall mounting only: Install the mounting bracket
using the supplied screws and mounting clips. Refer
to the section “Installing the mounting bracket” for
further details.
In st a llin g t h e m o u n t in g b ra cke t
The wall-mounted P/ 2 DA2 WM kit includes a mounting
bracket which is installed in a wall opening. The AAP
version of the P/ 2 DA2 WM uses a wider mounting
bracket, as shown below.
Before connecting any cables, power off all
equipment. If the optional Architectural Adapter
Plate (AAP) is being installed, please refer to
“Installing Architectural Adapter Plates” in this chapter.
1.
Once the proper wall location for mounting the
distribution amplifier has been selected, cut an
opening in the wall using the proper mounting
template found in the “Appendix” section.
The rear connectors are the same for both WM and
EC models. Please refer to figure 2-3. Connect the
VGA output cable to the 15-pin HD female output
connector. To prevent installation debris or objects
from entering the opening in the sheet metal just
above this VGA connector, it is suggested that some
masking tape be used to temporarily cover this
opening. Remove this tape after installation is
completed. Next, if there is audio output, connect
the audio output cable to the 3.5 mm captive screw
connector. Finally, connect the power cable to the
power input connector. Refer to the “Cabling” and
“Connecting audio” sections of this chapter.
2.
Using two supplied screws and mounting clips,
attach the mounting bracket to the hole opening, as
shown below.
wall mounting bracket
wall mounting bracket
for Architectural Adapter Plate
Backing Clip can
be in either orientation.
See Detail A or Detail B.
Backing Clip can
be in either orientation.
See Detail A or Detail B.
Mounting Bracket
Mounting Bracket
5
Before attaching the faceplate assembly to the wall
mounting bracket/ Euro Channel, attach the
Sheet Rock
computer video cable to the 15-pin HD female input
connector on the faceplate. Next, a local monitor
may be connected to the 15-pin HD female buffered
local monitor output connector on the faceplate.
Finally, for audio input, connect the audio cable to
the faceplate’s 3.5 mm audio input jack. Refer to the
“Cabling” and “Connecting audio” sections of this
chapter. For Euro Channel applications, refer to the
Sheet Rock
Backing Clip
Backing Clip
0.75" #6-32 Screw
1.25" #6-32 Screw
Mounting Bracket
Mounting Bracket
Detail B
Detail A
Fig u re 2-4 — In st a llin g t h e m o u n t in g b ra cke t
P/2 DA2 WM/EC Controls and Installation
2-4
P/2 DA2 WM/EC Controls and Installation
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n , co n t ’d
Ca b lin g
Co n n e ct in g a u d io o u t p u t
The P/ 2 DA2 WM cabling diagram below shows how to
Before connecting audio output, determine whether your
audio system is unbalanced or balanced. Then, follow the
instructions below to connect unbalanced audio, or the
instructions for “Balanced audio” to connect balanced
audio.
connect input and output devices to the distribution
amplifier ’s front panel. The P/ 2 DA2 EC model has
identical connectors.
Wiring the audio incorrectly may damage the
audio output circuits.
AUTO POWER
Un b a la n ce d a u d io
To attach the P/ 2 DA2 WM/ EC to an unbalanced audio
system, do the following:
100%
UNITY
50%
1.
Attach the audio cable to an unbalanced speaker
input connector (tip and sleeve).
GAIN/PEAKING
Tip Sleeve
Fig u re 2-5 — P/2 DA2 WM ca b lin g
1.
Connect your display device to the 15-pin HD female
video output VGA connector on the rear of the P/ 2
DA2 WM/ EC. See figure 2-3.
2.
Attach the audio cable to the audio cable connector
(Extron part number 10-319-10). Fasten the captive
screws inside the audio cable connector as shown in
figure 2-6.
2.
For audio output, refer to the section “Connecting
audio output” and connect the audio output cable to
the 3.5 mm captive screw connector on the rear of the
P/ 2 DA2 WM/ EC.
Unbalanced Output
Tip
See Warning
Sleeve (s)
Tip
See Warning
3.
4.
Connect the power input cable to the rear power
input connector of the P/ 2 DA2 WM/ EC.
Connect the computer’s video cable to the 15-pin HD
female Input cable on the distribution amplifier’s
faceplate.
Connect the sleeve(s) to ground (GND).
Connecting the sleeve(s) to a negative (-)
terminal will damage audio output circuits.
5.
6.
If a local monitor is being used, connect the monitor
to the 15-pin HD female buffered local monitor
output on the faceplate.
For audio input, connect the input device into the
front faceplate’s 3.5 mm female audio jack.
P/2 DA2 WM/EC Controls and Installation
2-6
P/2 DA2 WM/EC Controls and Installation
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n , co n t ’d
3.
Slide the audio cable connector into the audio output
connector on the interface.
In st a llin g Arch it e ct u ra l Ad a p t e r Pla t e s
The P/ 2 DA2 WM AAP may have up to 4 optional adapter
plates and the P/ 2 DA2 EC AAP can have up to 3 adapter
plates. The adapter plates provide a convenient method of
adding various connectors for specific audio and video
requirements. The adapter plates must be ordered
separately and must be attached to the faceplate and cabled
before attaching the WM AAP model to the wallmount
bracket or the EC AAP model to the Euro Channel. See
figure 2-7.
Fig u re 2-6 — Fa st e n in g ca p t ive scre w s
3.
Slide the audio cable connector into the audio output
connector on the interface.
Ba la n ce d a u d io
To attach the interface to a balanced audio system, do the
following:
1. Attach the audio cable to a balanced speaker input
connector (tip, ring, and sleeve).
1.
Insert the adapter plate captive screws through the
front faceplate holes. Secure the adapter plate using
the supplied washers and nuts.
Adapter Plate
Tip (+)
Sleeve
AUTO POWER
AUDIO
100%
UNITY
INPUT
50%
GAIN/PEAKING
BUFFERED
Ring (-)
ID PIN
4
LOCAL M
ID PIN 11
Tip (+)
#4-40 Nut w/ Captive
Washer
Sleeve
P/2 DA2 WM
(up to 4 Plates)
P/2
D
A2
WM
2.
Attach the audio cable to the audio cable connector
(Extron part number 10-319-10). Fasten the captive
screws inside the audio cable connector as shown in
figure 2-6.
P/2 DA2 EC AAP
AUTO POWER
GAIN/
PEAKING
ID PINS
P/2 DA2 EC
(up to 3 Plates)
Balanced Output
Tip
Ring
Sleeve (s)
Tip
Fig u re 2-7 — In st a llin g a d a p t e r p la t e s
Ring
2.
Attach the output cables to the back side of the
adapter plate. Some adapter plates may require that
conductors be soldered to the connectors. Attach foil
and braided shields to ground connections.
Connect the sleeve(s) to ground (GND).
Connecting the sleeve(s) to a negative (-)
terminal will damage audio output circuits.
P/2 DA2 WM/EC Controls and Installation
2-8
P/2 DA2 WM/EC Controls and Installation
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n , co n t ’d
P/2 DA2 EC Eu ro Ch a n n e l in st a lla t io n
Once the input and output cables have been connected and
tested on the P/ 2 DA2 EC, the distribution amplifier can be
easily installed in the Euro Channel. See figure 2-9.
P/2 DA2 WM w a llm o u n t in st a lla t io n
Once the input and output cables have been connected and
the P/ 2 DA2 WM has been successfully tested, the faceplate
may be attached to the mounting bracket using the 4
supplied screws. See figure 2-8.
WM
A2
P/2
D
11
ID PINS
4
The center pole of the power input connector
contains no conductor. Connect the conductors to
the two outer poles only, exactly as shown here.
AUTO POR
AUDIO
BUFFERE
LOC
GAIN/
INPU
PEAKING
Positive
N/C
Negative
Audio (3.5mm
Power (3.5mm
Captive Screw
Captive Screw
Connector)
Connector)
WM
A2
P/2
D
11
ID PINS
4
T
AUTO POER
AUDI
BUFFERED
LOCAL
GAIN/
INPU
Euro Channel
PEAKING
AUTO POWER
AUDIO
100%
UNITY
INPUT
50%
GAIN/PEAKING
BUFFERED
ID PIN
ID PIN 11
4
LOCAL M
P/2
D
A2
WM
Fig u re 2-9 — Eu ro Ch a n n e l in st a lla t io n
VGA Connector
Se t t in g t h e DIP sw it ch e s
Two sliding-type DIP switches can be found on the
faceplate of the P/ 2 DA2 WM/ EC.
1
2
To set the sliding-type DIP switches, slide the
switch to the on/ closed or off/ open position.
The two DIP switches provide proper ID bit termination for
a laptop computer that is not attached to a local monitor.
ID PIN 4 & ID PIN 11
ON — Set both pins to On if you are using the
ID PIN 4
ID PIN 11
P/ 2 DA2 WM/ EC with a laptop
computer that is not attached to a local
Fig u re 2-8 — Wa ll m o u n t in g t h e P/2 DA2 WM
monitor.
P/2 DA2 WM/EC Controls and Installation
2-10
P/2 DA2 WM/EC Controls and Installation
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Co n t ro ls a n d In st a lla t io n , co n t ’d
OFF — Set both pins to Off if you are attaching a
local monitor to the P/ 2 DA2 WM/ EC.
P/2 DA2 WM/EC
Appendix
A
Specifications
Faceplate Dimensions
Cables
Architectural Adapter Plates
Mounting Templates
P/2 DA2 WM/EC Controls and Installation
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix
Au d io in p u t
Number/ signal type ................... 1 stereo, unbalanced
P/2 DA2 WM/EC Sp e cifica t io n s
Connectors .................................... 1 3.5 mm female stereo jack, 2 channel; tip
(L), ring (R), sleeve (GND)
Vid e o in p u t
Number/ signal type ................... 1 VGA/ SVGA/ XGA/ SXGA RGBHV,
RGBS, RGsB, RsGsBs
Impedance .................................... 50 ohms, unbalanced
Connectors .................................... 1 15-pin HD male
Nominal level(s) .......................... Analog ....... 0.7V p-p
Minimum/ maximum level(s) .... Analog ....... 0.4V to 2.0V p-p with no offset
Impedance .................................... 75 ohms
Au d io t h ro u g h p u t
Gain ............................................... Unbalanced 0dB, balanced +6dB
Frequency response ..................... ±0.05dB @ 20 Hz to 20 kHz
S/ N ................................................ >90 kHz, output 21dB, balanced
Horizontal frequency .................. Autoscan 15 kHz to 135 kHz
Vertical frequency ....................... Autoscan 30 Hz to 170 Hz
Return loss .................................... -38.3dB @ 5 MHz
Maximum DC offset .................... 200mV
Au d io o u t p u t
Number/ signal type ................... 1 stereo, balanced/ unbalanced
Connectors .................................... 1 3.5 mm captive screw terminal, 5 pole
Impedance .................................... 50 ohms unbalanced; 100 ohms balanced
Vid e o t h ro u g h p u t
Gain ............................................... Unity, (0.1V) 15% peaking, (0.2V) 30%
peaking
Ge n e ra l
Power............................................. 12 to 24VAC or VDC, 0.5A, 5 watts,
external
Bandwidth .................................... 300 MHz (-3dB), fully loaded
Temperature/ humidity .............. Storage -40° to +158°F (-40° to +70°C) /
10% to 90%, non-condensing
Vid e o o u t p u t
Number/ signal type ................... 2 VGA/ SVGA/ XGA/ SXGA RGBHV,
RGBS, RGsB, RsGsBs
........................................................ Operating +32° to +122°F (0° to +50°C) /
10% to 90%, non-condensing
Connectors .................................... 2 15-pin HD female (1 display, 1 local
monitor)
Rack mount................................... No, but wall- or furniture-mountable
Enclosure type ..............................Metal
Nominal level ............................... Unity (1x input level)
Impedance .................................... 75 ohms
Enclosure dimensions
P/ 2 DA2 WM ................... Plate.. 4.50" H x 4.60" W (11.43 cm H x 11.68 cm W)
P/ 2 DA2 WM AAP .......... Plate.. 4.50" H x 8.20" W (11.43 cm H x 20.83 cm W)
P/ 2 DA2 WM EC .............. Plate.. 3.12" H x 3.94" W (7.92 cm H x 10.01 cm W)
P/ 2 DA2 WM EC AAP .... Plate.. 3.15" H x 7.69" W (8.00 cm H x 19.53 cm W)
Return loss .................................... -41dB @ 5 MHz
DC offset ....................................... ±5mV maximum
Syn c
All models......................... Box ... 3.00" H x 3.50" W x 1.60" D (7.62 cm H x
8.89 cm W x 4.06 cm D)
Input type ..................................... Autodetect RGBHV, RGBS, RGsB, RsGsBs
Output type .................................. Autodetect RGBHV, RGBS, RGsB, RsGsBs
Input level ..................................... 3.0V to 5.0V p-p
Output level .................................. TTL ............. 5.0V p-p
Input impedance .......................... 510 ohms
Shipping weight ........................... 2 lbs (0.9 kg)
Vibration ....................................... NSTA 1A in carton (National Safe Transit
Association)
Approvals ..................................... UL, CE
Output impedance ....................... 75 ohms
MTBF ............................................. 30,000 hours
Warranty ....................................... 2 years parts and labor
Max. propagation delay .............. 18.8 nS
Max. rise/ fall time ....................... 4 nS
Polarity .......................................... Positive or negative (follows input)
Specifications are subject to change without notice.
P/2 DA2 WM/EC Appendix
A-2
P/2 DA2 WM/EC Appendix
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix, co n t ’d
P/2 DA2 WM Fa ce p la t e Dim e n sio n s
Dimensions of the P/ 2 DA2 WM and its AAP version are
provided here for those who wish to make their own
customized faceplate. The following diagrams are not drawn to
scale.
HAND SAND TO 0.06" RADIUS
AROUND THE TOP OF
THESE EDGES.
THRU
.120 THRU
.210 THRU
.210 THRU
DETAIL
A
Fig u re A-2 — WM m o d e l AAP fa ce p la t e d im e n sio n s
DETAIL A
All dimensions are given in inches.
Fig u re A-1 — WM m o d e l fa ce p la t e d im e n sio n s
All dimensions are given in inches.
P/2 DA2 WM/EC Appendix
A-4
P/2 DA2 WM/EC Appendix
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix, co n t ’d
Ca b le s
Op t io n a l Arch it e ct u ra l Ad a p t e r Pla t e s
The table below lists various lengths of high resolution VGA
cables which can be used with the P/ 2 DA2 WM/ EC.
A variety of optional adapter plates for pass-through
connections may be ordered for the P/ 2 DA2 WM/ EC. See the
figure A-3 below. The WM model can accommodate up to 4
adapter plates and the EC model can handle up to 3 adapter
plates. The adapter plates come in 2 sizes: one and two.
Male-to-fem ale VGA cables
Pa rt n u m b e r
VGA 6’ HR
26-112-15
29-491-01
29-491-02
29-491-03
29-491-04
29-491-05
The WM model may be configured as follows:
• 4 adapter plates of plate size one or
• 2 adapter plates of plate size two or
VGA 3’ HR A (with audio)
VGA 6’ HR A (with audio)
VGA 12’ HR A (with audio)
VGA 25’ HR A (with audio)
VGA 50’ HR A (with audio)
• 2 adapter plates of plate size one and
one adapter plate of plate size two
The EC model may be configured as follows:
• 3 adapter plates of plate size one or
• 1 adapter plate of plate size two and
1 adapter plate of plate size one
Blank Plate (no connector)
Single Space
Blank Plate (no connector)
Double Space
2 - BNC
5 - BNC (Double)
3 - BNC
2 - RCA to Solder Cups
3 - RCA to Solder Cups
2 - S-video
2 - RJ-11
1 - D-9 Pass Through Connector
Fig u re A-3 — Exa m p le s o f a d a p t e r p la t e s
The tables on following pages list the available adapter plates
and distinguish between plates with a single type of connector
(Single type) or plates with more than one type of connector
(Multi type).
P/2 DA2 WM/EC Appendix
A-6
P/2 DA2 WM/EC Appendix
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Sin g le Typ e Co n n e ct o r Arch it e ct u ra l Ad a p t e r Pla t e s
Pla t e
size
Fro n t
co n n e ct o r t yp e
Re a r
co n n e ct o r t yp e
Ad a p t e r p la t e d e scrip t io n
Pa rt # Gra y Bla ck Wh it e
Blank plate 1
1
2
1
1
2
1
1
n.a.
n.a.
n.a.
70-090
70-090
70-091
70-091
70-091
70-092
70-092
-01
-02
-01
-02
-03
-01
-02
-11
-12
-11
-12
-13
-11
-12
-21
-22
-21
-22
-23
-21
-22
Blank plate 2
n.a.
2 BNC barrel (female to female)
3 BNC barrel (female to female)
5 BNC barrel (female to female)
2 RCA female to solder cups
3 RCA female to solder cups
BNC female
BNC female
BNC female
BNC female
solder lug terminals
solder lug terminals
BNC female
BNC female
RCA female (red/ black)
RCA female (red/ black)
2 RCA female barrel
(female to female)
1
1
1
1
1
RCA female (red/ black)
RCA female (red/ black)
RCA female (red/ black)
RCA female (red/ black)
4-pin mini DIN female
RCA female
RCA female
70-093
70-093
70-094
70-094
70-095
-01
-02
-01
-02
-01
-11
-12
-11
-12
-11
-21
-22
-21
-22
-21
3 RCA female barrel
(female to female)
2 RCA to BNC barrel
(female to female)
BNC female
3 RCA to BNC barrel
(female to female)
BNC female
2 S-video to S-video barrel
(female to female)
4-pin mini DIN female
2 F connector barrel
2 ¼" stereo phono female
2 ¼" mono phono female
2 3.5mm mini stereo female
2 RJ-11 (female to female)
2 RJ-45 (female to female)
1 HD-15 (female to female)
1 HD-15 (male to male)
1 D-9 (female to female)
1 D-9 (male to male)
1
1
1
1
2
2
1
1
1
1
2
2
2
F connector female
¼" stereo phono female
¼" mono phono female
3.5mm mini stereo female
RJ-11 female
F connector female
3 solder lug terminals
2 solder lug terminals
3 solder lug terminals
RJ-11 female
70-096
70-097
70-097
70-098
70-099
70-100
70-101
70-101
70-102
70-102
70-103
70-103
70-103
-01
-01
-02
-01
-01
-01
-01
-02
-01
-02
-01
-02
-03
-11
-11
-12
-11
-11
-11
-11
-12
-11
-12
-11
-12
-13
-21
-21
-22
-21
-21
-21
-21
-22
-21
-22
-21
-22
-23
RJ-45 female
RJ-45 female
15-pin HD female
15-pin HD male
15-pin HD female
15-pin HD male
9-pin D female
9-pin D female
9-pin D male
9-pin D male
1 3-pin XLR female
3-pin XLR female
4-pin XLR female
6-pin XLR female
3 solder lug terminals
3 solder lug terminals
3 solder lug terminals
1 4-pin XLR female
1 6-pin XLR female
2 6-pin mini DIN
(keyboard/ mouse)
1
1
6-pin mini DIN female
6-pin mini DIN female
solder cups
70-104
70-105
-01
-01
-11
-11
-21
-21
1 3.5mm, 5 pole
captive screw terminal
3.5mm, 5 pole
captive screw terminal
1 contact closure switch/
LED show-me and
3.5mm stereo mini jack
contact closure switch and
3.5mm mini stereo jack
1
solder cups
70-106
-01
-11
-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Ap p e n d ix, co n t ’d
P/2 DA2 WM Mo u n t in g Te m p la t e
Use this template as a guide for cutting the hole in the
installation surface (wall or furniture). This diagram is shown
at actual size.
The light gray area represents where
the P/2 DA2 WM enclosure (2.562” H x 3.437” W)
will be located against the rear of the
P/2 DA2 WM front panel.
The solid, outer line (4.50” H x 4.60” W)
represents the outside edge
of the wall mounting bracket.
The dotted line indicates the recommended
cut-out area (3.875” H x 3.80” W)
for the installation surface.
P/2 DA2 WM/EC Appendix
A-10
P/2 DA2 WM/EC Appendix A-11
Download from Www.Somanuals.com. All Manuals Search And Download.
The solid, outer line (4.50” H x8.325” W)
represents the outside edge
of the wall mounting bracket.
The dashed line indicates the recommended
cut-out area (3.875” H x 7.525” W)
for the installation surface.
Download from Www.Somanuals.com. All Manuals Search And Download.
|