Extron electronic Satellite Radio PVT CV User Manual

User’s Guide  
PVT CV, PVT RGB CV,  
PVT RGB and PVT SW RGB  
PoleVaultTwisted Pair Transmitters  
(Rack Mount Models)  
68-1310-01  
Rev. C  
04 07  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Precautions  
䄺ਞ  
ᅝܼ乏ⶹꢀꢀ噝ꢀꢀЁ᭛  
⬉⑤ꢀ噝ꢀ䆹䆒໛া㛑Փ⫼ѻકϞᷛᯢⱘ⬉⑤DŽꢀ䆒໛ᖙ⫼᳝  
ഄ㒓կ⬉㋏㒳կ⬉DŽ㄀ϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ  
⫼៪䏇䖛DŽ  
䖭Ͼヺোᦤ⼎⫼᠋䆹䆒໛⫼᠋᠟
ݠ
Ё  
ⱘ᪡԰੠㓈ᡸ䇈ᯢDŽ  
ᢨᥝ⬉⑤ꢀ噝ꢀЎᅝܼഄҢ䆒໛ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝  
ꢀꢀ໛ৢ៪Ḡ䴶⬉⑤ⱘ⬉⑤㒓ˈ៪ӏԩ᥹
Ꮦ⬉㋏㒳  
ꢀꢀ⬉⑤㒓DŽ  
ꢀ䖭Ͼヺো䄺ਞ⫼᠋䆹䆒໛ᴎ໇
ݙ
ᲈ  
ꢀ䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ  
⬉⑤㒓ֱᡸꢀ噝ꢀཹ୘Ꮧ㒓ˈꢀ䙓
ܡ
㹿䏽䏣ˈ៪䞡⠽᣸य़DŽ  
㓈ᡸꢀ噝ꢀ᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎਬ䖯㸠DŽꢀ䆒໛  
ꢀꢀ䚼≵᳝⫼᠋ৃҹ᳈ᤶⱘ䳊ӊDŽЎ䙓
ߎܡ
⦄㾺⬉ॅ  
ꢀꢀϡ㽕㞾Ꮕ䆩೒ᠧᓔ䆒໛Ⲫᄤ㓈ׂ䆹䆒໛DŽ  
䗮亢ᄨꢀ噝ꢀ᳝ѯ䆒໛ᴎ໇Ϟ᳝䗮亢ῑ៪ᄨˈᅗӀᰃ⫼  
ꢀꢀ䰆ℶᴎ
ݙ
ᬣᛳ
ܗ
ӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ  
䫖⬉∴ꢀ噝ꢀϡℷ⹂ⱘ᳈ᤶ⬉∴Ӯ᳝⟚⚌ⱘॅ䰽DŽᖙ乏Փ  
ꢀꢀϢॖᆊ᥼㤤ⱘⳌৠ៪Ⳍ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻॖⱘ  
⊼ᛣ  
䯙䇏䇈ᯢкꢀ噝ꢀ⫼᠋Փ⫼䆹䆒໛ࠡᖙ乏䯙䇏ᑊ⧚㾷  
ꢀꢀ᳝ᅝܼ੠Փ⫼䇈ᯢDŽ  
ֱᄬ䇈ᯢкꢀ噝ꢀ⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹ໛ᇚᴹՓ⫼DŽ  
ꢀꢀ䙉ᅜ䄺ਞꢀ噝ꢀ⫼᠋ᑨ䙉ᅜѻક੠⫼᠋ᣛफϞⱘ᠔᳝  
ꢀꢀᅝܼ੠᪡԰䇈ᯢDŽ  
ܡ
ꢀ噝ꢀϡ㽕Փ⫼䆹ѻકॖଚ≵᳝᥼㤤ⱘᎹ
݋
៪  
ꢀꢀ䗑
䆒໛ˈҹ䙓
ܡ
ॅ䰽DŽ  
ꢀꢀ䆂໘⧚ᑳᓗ⬉∴DŽ  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This page was deliberately left blank.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents  
Chapter One • Introduction..................................................... 1-1  
About the PVT SW RGB.......................................................... 1-4  
UL/Safety Requirements.......................................................... 2-2  
Important safety instructions................................................ 2-2  
Tabletop use............................................................................ 2-3  
UL requirements for rack mounted devices.......................... 2-3  
Rack mounting........................................................................ 2-3  
Furniture mounting................................................................ 2-5  
transmission...................................................................... 2-9  
audio transmission.......................................................... 2-11  
Appendix A • Reference Material ......................................A-1  
All trademarks mentioned in this manual are the properties of their respective owners.  
68-1310-01  
Rev. C  
04 07  
PVT Series (Rack Mount Models) • Table of Contents  
i
Download from Www.Somanuals.com. All Manuals Search And Download.  
Table of Contents, cont'd  
This page was deliberately left blank.  
ii  
PVT Series (Rack Mount Models) • Table of Contents  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVT Series (Rack Mount Models)  
Chapter One  
1
Introduction  
About.the.PVT.Transmitters  
Application.Diagram  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Introduction  
About the PVT Transmitters  
The Extron P�T Series (PoleaultTwisted Pair Transmitters)  
are a series of cost effective twisted pair transmitters that work  
exclusively with the PVS 204SA, a four-input twisted pair  
switcher with a built in power amplifier.  
PVT transmitters can transmit composite video and stereo audio  
or high resolution video (RGB) and stereo audio to the  
PVS 204SA switcher over CAT 5 twisted pair cable, up to a  
distance of 100 feet. All transmitters are remotely powered  
via the twisted pair cable when connected to the PVS 204SA  
switcher.  
This manual covers the rack mount models only.  
For Decora® and AAP models, refer to the manual (part  
number 68-1259-01) for those devices.  
N
PVT series of transmitters are compatible ONLY  
with the PVS 204SA switcher.  
N
N
For PVS 204SA installation and operation information,  
refer to the manual supplied with the device.  
The PVT transmitter rack mount models can be mounted on 1U  
19" or standard rack shelves, or mounted under or on desks.  
The PVT series rack mount models are as follows:  
PVT CV — Transmits composite video and stereo audio.  
PVT RGB, PVT SW RGB — Transmits computer (RGB) video  
and stereo audio.  
PVT RGB CV — Transmits composite video, computer video  
and two stereo audio signals.  
See the "About the PVT xx" sections in this chapter for details.  
The PVT transmitters are part of a system for distribution of  
composite or computer video and audio, over Extron Enhanced  
Skew-Free™ A/V UTP Cable, or any CAT 5, 5e, or 6 shielded  
twisted pair (STP), unshielded twisted pair (UTP), or foil  
shielded twisted pair (FTP) cable.  
Transmission distance  
The maximum distance is determined by the frequency and  
resolution of the signal that is input to the transmitter. However,  
all PVT models can transmit signals to the PVS 204SA switcher  
if it is located not more than 100 feet away. The optimum  
distance is between 50 and 75 feet.  
1-2  
PVT Series (Rack Mount Models) • Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
About the PVT CV  
The P�T C� Twisted Pair Transmitter is a 1/8 rack mounting  
model that can transmit composite video and stereo audio to the  
PVS 204SA switcher. This model can also be mounted under a  
desk or shelf, or on certain projector poles.  
AUDIO  
IN  
L
VIDEO  
IN  
R
VIDEO OUT  
PVT CV  
Figure 1-1 — PVT CV face and rear panel  
About the PVT RGB  
The P�T RGB Twisted Pair Transmitter is a 1/4 rack mounting  
model that can transmit high resolution (RGB) video and an  
associated stereo audio signal to the PVS 204SA switcher. It has  
a local monitor output for image monitoring. This model can  
also be mounted under a desk or shelf, or on certain projector  
poles.  
PVT RGB  
PVT RGB  
RGB A OUT  
MONITOR OUT  
INPUT  
RGB B OUT  
Figure 1-2 — PVT RGB face and rear panel  
PVT Series (Rack Mount Models) • Introduction  
1-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Introduction, cont’d  
About the PVT RGB CV  
The P�T RGB C� Twisted Pair Transmitter is a 1/4 rack  
mounting model that can transmit high resolution (RGB) video  
and composite video, and two associated stereo audio signals to  
the PVS 204SA switcher. This model can also be mounted under  
a desk or shelf, or on certain projector poles.  
RGB  
VIDEO  
PVT RGB CV  
RGB A OUT  
AUDIO  
IN  
AUDIO IN  
L
VIDEO  
IN  
COMPUTER IN  
R
VIDEO OUT  
RGB B OUT  
Figure 1-3 — PVT RGB CV face and rear panel  
About the PVT SW RGB  
The P�T SW RGB Twisted Pair Transmitter is a 1/4 rack  
mounting model with two input connectors, a local monitor  
output, and a remote contact closure connector. It transmits  
high resolution (RGB) video and stereo audio signals to the  
PVS 204SA, and switches between the two inputs by front  
panel, remote, or auto switching. In addition, the local monitor  
output can be set to accept only the input 1 signal, or to follow  
the current active input signal. This model can also be mounted  
under a desk or shelf, or on certain projector poles.  
AUTO  
SWITCH  
ON  
FOLLOW  
MONITOR  
AUTO  
1
2
MANUAL  
INPUT  
1
PVT SW RGB  
REMOTE  
INPUT 1  
RGB A OUT  
PIN1 - IN 1  
PIN4 - IN 2  
PIN5 - GND  
CONTACT  
RGB B OUT  
INPUT 2  
MONITOR OUT  
Figure 1-4 — PVT SW RGB face and rear panel  
PVT Series (Rack Mount Models) • Introduction  
1-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Application Diagram  
Extron  
SI 26X  
Two-way, Open Back  
Ceiling Speakers – 1 Pair  
Option  
Extron  
SI 26X  
Two-way, Open Back  
Ceiling Speakers – 1 Pair  
Extron  
SPK 18 - 25'  
Cable  
Included  
Extron  
PCM 240  
Projector Drop  
Ceiling Mount  
Extron  
PMP  
Projector  
Mount Pole  
Extron  
PVS 204SA  
TS  
ms  
PU  
4/8  
Oh  
IE  
D
O
UT  
PLIF  
AM  
R
UN
SP  
OL  
O
O
!  
L
DC  
V
/IR  
L
C
1
2
V
1
I
K
2
32  
R
M
L
T
I
/
x
I
PoleVault  
Switcher  
R
1
0V U
L/
S
T
O
®
C
B
A
B
N  
/I  
RG  
O
T
T
A
U
EO  
A
VID  
3
2A  
B
RG  
1A  
I
3
I
N
P
U
T
B  
R
S
WE  
1B  
PO  
12VMAX  
3A  
Extron  
PMK 350  
Multi-product Projector  
Mounting Kit  
Hardwired IR Cable  
to Switcher Included  
Extron  
UPB 25  
Universal Projector  
Mounting Bracket  
Y
A
L
P
S
I
D
O
F
F
O
N
C
P
O
E
O
ID  
V
V
L
O
V
RS-232 Cable  
to Projector  
Included  
2
5
C
L
M
UTP Cable  
Included  
Extron  
MLC 52 RS  
Basic MediaLink  
Controller  
Extron  
PVT RGB CV  
VGA, Composite Video  
W/Audio UTP Transmitter  
Line Level  
Audio  
A
C
T
IV  
E
M
U
T
E
M
IC  
IN  
A
U
IN  
D
IO  
V
ID  
IN  
E
O
L
A
U
D
IO  
IN  
R
R
G
COM  
PU  
B
A
O
V
U
T
ID  
TE  
Extron  
E
R
O
IN  
O
U
T
R
MLP 101 D  
G
B
B
O
U
T
Mic to Line Preamplifier  
Option  
Extron  
PVT CV  
Composite Video  
w/ Audio UTP  
Transmitter  
Option  
DVD/VCR Combo  
Laptop  
w/ Audio  
A
U
IN  
DI  
O
VI  
D
IN  
EO  
L
R
V
D
EO
T
Aux. Video Source  
Figure 1-5 — Typical PVT series system application  
using PVT RGB CV and PVT CV transmitters with the  
PVS 204SA and other Extron devices  
1-5  
PVT Series (Rack Mount Models) • Introduction  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Introduction, cont'd  
This page was deliberately left blank.  
PVT Series (Rack Mount Models) • Introduction  
1-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVT Series (Rack Mount Models)  
Chapter Two  
2
Installation  
UL/Safety.Requirements  
Installing.the.PVT.Twisted.Pair.Transmitters  
Connections.and.Settings  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation  
UL/Safety Requirements  
The Underwriters Laboratories (UL) requirements listed below  
pertain to the safe installation and operation of the transmitters.  
Important safety instructions  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
Read these instructions.  
Keep these instructions.  
Heed all warnings.  
Follow all instructions.  
Do not use this apparatus near water.  
Clean only with a dry cloth.  
Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8.  
9.  
Do not install near any heat sources such as radiators, heat  
registers, stoves, or other apparatus (including amplifiers)  
that produce heat.  
Do not defeat the safety purpose of the polarized or  
grounding type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If  
the provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
10. Protect the power cord from being walked on or pinched  
particularly at plugs, convenience receptacles, and the  
point where they exit from the apparatus.  
11. Only use attachments/accessories specified by the  
manufacturer.  
12. Use only with the cart, stand, tripod, bracket, or table  
specified by the manufacturer, or sold with the apparatus.  
When a cart is used, use caution when moving the cart/  
apparatus combination to avoid injury from tip-over.  
13. Unplug this apparatus during lightning storms or when  
unused for long periods of time.  
14. Refer all servicing to qualified service personnel. Servicing  
is required when the apparatus has been damaged in any  
way, such as power-supply cord or plug is damaged, liquid  
has been spilled or objects have fallen into the apparatus,  
the apparatus has been exposed to rain or moisture, does  
not operate normally, or has been dropped.  
PVT Series (Rack Mount Models) • Installation  
2-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Installing the PVT Twisted Pair Transmitters  
The PVT CV is a 1/8 rack shelf mountable transmitter, and  
the PVT RGB, PVT RGB CV, and PVT SW RGB are 1/4 rack  
shelf mountable transmitters. Each of the four models can  
be mounted under a desk or shelf, or on to certain projector  
mounts, and are also suitable for tabletop use.  
Tabletop use  
The PVT comes with self-adhesive rubber feet attached to the  
four corners of the bottom. Set the PVT on a horizontal surface.  
UL requirements for rack mounted devices  
The following Underwriters Laboratories (UL) requirements  
pertain to the safe installation of the PVT transmitter in a rack.  
1.  
Elevated operating ambient temperature — If installed in  
a closed or multi-unit rack assembly, the operating ambient  
temperature of the rack environment may be greater than  
room ambient temperature. Therefore, install the device  
in an environment compatible with the maximum ambient  
temperature (Tma = +122 °F, +50 °C) specified by Extron.  
2.  
3.  
4.  
Reduced air flow — Install the equipment in a rack so that  
the amount of air flow required for safe operation of the  
equipment is not compromised.  
Mechanical loading — Mount the equipment in the rack  
so that a hazardous condition is not achieved due to  
uneven mechanical loading.  
Circuit overloading — Connect the equipment to  
the supply circuit and consider the effect that circuit  
overloading might have on overcurrent protection and  
supply wiring. Appropriate consideration of equipment  
nameplate ratings should be used when addressing this  
concern.  
5.  
Reliable earthing (grounding) — Maintain reliable  
grounding of rack-mounted equipment. Pay particular  
attention to supply connections other than direct  
connections to the branch circuit (e.g., use of power strips).  
Rack mounting  
For rack mounting, mount the PVT on a VersaTools® 19" 1U  
rack shelf (RSF 123, part #60-190-20 or RSB 123, #60-604-20)  
(figure 2-1) or on a standard 1U rack shelf (RSU 129, part #60-  
190-01 or RSB 129, #60-604-01) (figure 2-2). On standard rack  
shelves, the PVT CV can be mounted in one of eight locations to  
the rear or the front of the rack, and the PVT RGB and RGB CV  
in one of four locations to the rear or front of the rack.  
PVT Series (Rack Mount Models) • Installation  
2-3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
       
Installation, cont’d  
To rack mount a PVT transmitter, do the following:  
1.  
2.  
If installed, remove the feet from the bottom of the PVT.  
Mount the PVT using two 4-40 x 3/16" screws in opposite  
(diagonal) corners to secure the PVT to the shelf.  
3.  
Install blank panel(s) or other unit(s) to the rack shelf.  
VersaTools  
Rack Shelf  
Eighth Rack  
Width Device  
Quarter Rack  
Width Device  
Quarter and Eighth  
Rack Width False  
Front Face Plate  
(2) 4-40 x 3/16"  
Screws  
Figure 2-1 — Mounting the PVT on a VersaTools rack  
shelf  
Quarter Rack  
Width Device  
Eighth Rack  
Width Device  
M
D
D
A
IS  
T
S
N
R
IB  
E
A
U
R
IE  
T
IO  
S
M
P
L
IF  
IE  
R
Figure 2-2 — Mounting the PVT on a standard rack  
shelf  
PVT Series (Rack Mount Models) • Installation  
2-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Furniture mounting  
Use the optional mounting kit (MBU 123, under desk mounting  
kit, part #70-212-01) to mount the PVT as follows:  
1.  
2.  
If installed, remove the feet from the bottom of the PVT.  
Attach the mounting brackets to the PVT with the machine  
screws provided (figure 2-3).  
Figure 2-3 — Mounting the PVT under a desk  
3.  
Hold the PVT with the attached brackets against the  
underside of the mounting surface. Mark the bracket  
screw hole locations on the mounting surface.  
4.  
5.  
6.  
Drill four 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)  
deep in the mounting surface at the marked locations.  
Insert #8 wood screws into the pilot holes. Tighten the  
screws until just less than 1/4" of the head protrudes.  
Align the mounting screws with the slots in the brackets  
and place the PVT against the surface, with the screws  
through the bracket slots.  
7.  
Slide the PVT slightly forward or back, then tighten all  
four screws to secure the PVT in place.  
2-5  
PVT Series (Rack Mount Models) • Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
Connections and Settings  
N
Do not connect these devices to a computer data  
or telecommunications network. Do not connect  
these devices to an MTP system.  
Front panel features  
The front panel features are the same for the PVT CV, PVT RGB,  
and PVT RGB CV. The PVT SW RGB features are unique to that  
model.  
1
PVT CV  
PVT CV  
1
PVT RGB  
PVT RGB  
1
RGB  
VIDEO  
PVT RGB CV  
PVT RGB CV  
2
3
4
FOLLOW  
MONITOR  
AUTO  
AUTO  
SWITCH  
ON  
1
2
MANUAL  
INPUT  
1
PVT SW RGB  
PVT SW RGB  
Figure 2-4 — PVT series front panel features  
2-6  
PVT Series (Rack Mount Models) • Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Dual color power LED — This LED lights amber when  
power only (no signal) is applied to the PVT, and green  
when power and a signal are both present.  
a
AUTO  
SWITCH  
Auto switch LED (P�T SW RGB only) — This LED  
lights green when the unit is in auto switch mode.  
b
c
Input selection button with LED (P�T SW RGB only) —  
Press these buttons to select (switch) between inputs  
1 and 2. The associated LEDs lights green when  
the input has an active video signal connected, and  
amber when there is no signal present.  
1
Dual configuration dual DIP switch (P�T SW RGB only) —  
d
The left DIP switch allows the user to  
FOLLOW  
MONITOR  
INPUT 1  
AUTO  
ON  
select the switching mode, and the right  
DIP switch allows the user to configure  
the local monitor output from the rear  
panel.  
MANUAL  
Switching mode (left DIP switch):  
Set the switch up to Auto for automatic switching of the inputs  
with an active signal.  
When turning off auto switching, the PVT goes back to  
the input that was selected prior to turning the auto-  
switching on.  
N
Set the switch down to Manual for front panel input switching  
or input switching by contact closure control.  
In Auto mode, if both inputs have an active signal,  
Input 1 has priority.  
N
Local monitor output (right DIP switch):  
Set the switch up to Follow for automatic switching of the local  
monitor output to the current selected input.  
Set the switch down to Input 1 for local monitor output of the  
signal from input 1 only.  
2-7  
PVT Series (Rack Mount Models) • Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation, cont’d  
Rear panel features  
For all PVT rack mount models, the input connectors and the  
output connectors are on the rear panel (see figure 2-5).  
1
2
AUDIO  
IN  
L
VIDEO  
IN  
R
VIDEO OUT  
PVT CV  
3
4
1
2
RGB A OUT  
AUDIO  
IN  
AUDIO IN  
6a  
6b
L
VIDEO  
IN  
COMPUTER IN  
R
VIDEO OUT  
RGB B OUT  
PVT RGB CV  
3
5
PVT RGB  
RGB A OUT  
6a  
6b
MONITOR OUT  
INPUT  
RGB B OUT  
PVT RGB  
4
4
5
7
5
8
REMOTE  
INPUT 1  
RGB A OUT  
6a  
6b
PIN1 - IN 1  
PIN 4 - IN 2  
PIN 5 - GND  
CONTACT  
RGB B OUT  
INPUT 2  
MONITOR OUT  
PVT SW RGB  
4
5
7
Figure 2-5 — PVT rear panel features  
PVT Series (Rack Mount Models) • Installation  
2-8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Composite video input (C� and RGB C� models) —  
To input a composite video signal from a suitable source,  
connect a male RCA plug to this yellow female RCA jack.  
a
b
Audio (left and right) input (C� and RGB C� models) —  
For unbalanced left and right audio input, insert male RCA  
plugs from the audio source, into these two female RCA jacks  
(white = left, red = right).  
Tip (Signal)  
Right Channel  
(Red Jacket)  
Sleeve (Gnd )  
Left Channel  
(White Jacket)  
Tip (+)  
Sleeve (  
)
Figure 2-6 — RCA audio connectors  
Composite video/audio output (C� and RGB C� models) —  
For composite video and audio output, using TP cable, connect  
this RJ-45 female output port to one of the two composite  
video RJ-45 input connectors (labeled 3 and 4), on the rear panel  
of the PVS 204SA switcher (see figure 2-8).  
c
Cable termination for composite video and audio transmission  
The PVT cable termination method is specific for PVT  
transmitters working with the PVS 204SA switcher.  
DO NOT connect these devices to an MTP system.  
N
N
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and  
Skew-Free A/V UTP cable must comply with the  
TIA/EIA T 568A wiring standards for all connections.  
For composite video signals, the RJ-45 connector must  
be wired exactly as shown in figure 2-7, so that the input  
video and audio signals are transmitted correctly.  
2-9  
PVT Series (Rack Mount Models) • Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
Clip Down  
Side  
Pins 12345678  
RJ-45  
TP Cable and  
CAT 5 connector  
connector  
Composite  
568A  
Video and Audio signal  
Pin  
Wire color  
1
White-green  
Green  
Video +  
Video –  
12345678  
2
3
4
5
White-orange  
Blue  
+ 5 VDC  
Audio L +  
Audio L –  
GND  
White-blue  
Twisted  
pairs  
6
7
8
Orange  
White-brown  
Brown  
Audio R +  
Audio R –  
1&2  
7&8  
3&6 4&5  
Figure 2-7 — Wiring the twisted pair composite  
video and audio cable  
PVT CV  
PVT RGB CV  
PVS 204SA  
RGB A OUT  
AUDIO  
IN  
AUDIO  
IN  
AUDIO IN  
VIDEO  
3
L
L
VIDEO  
IN  
COMPUTER IN  
VIDEO  
IN  
R
R
TP cable from  
PVT Output  
VIDEO OUT  
RGB B OUT  
VIDEO OUT  
Rear Panel  
Rear Panel  
TP cable from  
PVT Output  
4
Composite Video Input Connectors  
on Rear Panel of PVS 204SA  
Figure 2-8 — Connecting the PVT composite video  
outputs to the PVS 204SA switcher  
Audio input (RGB C, RGB and SW RGB models) —  
d
AUDIO IN  
Plug a 3.5 mm stereo audio plug into this jack for  
unbalanced audio input. Wire the plug as shown in  
figure 2-9.  
N
Figure 2-9 shows a typical audio connector, which  
consists of tip, ring, and sleeve.  
Tip (L)  
Ring (R)  
Sleeve (  
)
Figure 2-9 — 3.5 mm stereo audio plug  
PVT Series (Rack Mount Models) • Installation  
2-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
RGB video input (RGB C, RGB, and SW RGB models) —  
Connect a computer video source to this 15-pin HD  
connector for high resolution RGB video input.  
e
ä
RGB cable A output (RGB C, RGB, and SW RGB models) —  
Using TP cable, connect this RJ-45 female output port,  
labeled "RGB A out", to one of the two input ports  
(labeled 1A and 2A) on the PVS 204SA switcher.  
RGB cable B output (RGB C, RGB, and SW RGB models) —  
Using TP cable, connect this RJ-45 female output port,  
labeled "RGB B out", to one of the two input ports  
(labeled 1B and 2B) on the PVS 204SA switcher.  
ã
Cable termination for RGB video and audio transmission  
The PVT cable termination method is specific for PVT  
transmitters working with the PVS 204SA switcher.  
DO NOT connect these devices to an MTP system.  
N
N
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and  
Skew-Free A/V UTP cable must comply with the  
TIA/EIA T 568A wiring standards for all connections.  
For RGB signals, the RJ-45 connectors must be wired  
exactly as shown in the figure 2-10, using the same  
wiring table for both ends, so that the correct input  
signal (video on cable A and audio on cable B) is carried.  
Cable B carries the audio signal, the vertical sync  
information, and 5 VDC to power the PVT transmitters.  
N
Clip Down  
Side  
Pins 12345678  
RJ-45  
TP Cable and  
CAT 5 Connector  
Connector  
568A  
Pin Wire Color  
Cable B  
Cable A  
1
2
3
4
5
White-green  
Green  
V. sync +  
V. sync –  
+ 5 VDC  
Audio L +  
Audio L –  
Red +  
Red –  
12345678  
White-orange  
Blue  
H. sync +  
Green +  
Green –  
H. sync –  
Blue +  
White-blue  
Twisted  
Pairs  
6
7
8
Orange  
GND  
White-brown  
Brown  
Audio R +  
Audio R –  
Blue –  
1&2  
7&8  
3&6 4&5  
Figure 2-10 — Wiring twisted pair cables A and B  
2-11  
PVT Series (Rack Mount Models) • Installation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Installation, cont’d  
PVT SW RGB  
REMOTE  
TP Cable from  
RGB A OUT  
TP Cable from  
output A  
output A  
PVS 204SA  
PVT RGB  
PIN 1 — IN  
PIN 4 — IN  
PIN 5 — GND  
1
2
CONTACT  
RGB A OUT  
RGB  
1A  
2A  
I
N
P
U
T
S
RGB B OUT  
MONITOR OUT  
MONITOR OUT  
POWER  
Rear  
Panel  
RGB B OUT  
1B  
2B  
Rear Panel  
TP Cable from  
output B  
12V  
3A MAX  
TP Cable from  
output B  
RGB Input Connectors on  
Rear Panel of PVS 204SA  
Figure 2-11 — Connecting RGB outputs A and B to  
the PVS 204SA switcher  
MONITOR OUT  
Monitor output (RGB and SW RGB models) —  
Connect a local monitor device to this 15-pin HD  
connector to view the video input.  
g
The PVT SW RGB allows the user to view the image  
from input 1 only or, by adjusting the front panel DIP  
switch, to view the image from either input 1 or input 2.  
N
Remote contact closure connector (SW RGB model only) —  
Connect a contact closure device to this 15-pin HD connector  
to switch between input 1 and input 2 video signals. The  
connector has the pin assignments as shown in the table below.  
h
Pin  
Function  
1
2
3
4
5
6
7
8
9
Input #1  
Not used  
Not used  
Input #2  
Ground  
Not used  
Not used  
Not used  
Not used  
REMOTE  
PIN 1 — IN 1  
PIN 4 — IN 2  
PIN 5 — GND  
CONTACT  
PVT Series (Rack Mount Models) • Installation  
2-12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PVT Series (Rack Mount Models)  
Appendix A  
A
Reference Material  
Specifications  
Part.Numbers  
Optional.Accessories  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Reference Material  
Specifications  
N
These transmitters are compatible only with the Extron  
PVS 204SA. They are not compatible with other models of  
twisted pair receivers.  
Video — RGB (RGB models)  
Gain ................................................ Unity  
Video input and loop-through — RGB (RGB models)  
Number/signal type..................... 1 VGA-UXGA RGBHV, RGBS  
(2 for PVT SW RGB, and 1 buffered loop  
through)  
Connectors ..................................... 1 female 15-pin HD (2 for PVT SW RGB)  
Nominal level ................................ 0.7 Vp-p for RGB  
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset  
Impedance ..................................... 75 ohms  
Horizontal frequency.................... 15 kHz to 130 kHz  
Vertical frequency.......................... 30 Hz to 150 Hz  
Return loss ..................................... <-30 dB @ 5 MHz  
DC offset (max. allowable)........... 250 mV  
Video output — RGB (RGB models)  
Number/signal type..................... 2 analog proprietary signals  
Connectors .................................... 2 female RJ-45  
Sync — RGB (RGB models)  
Input type ...................................... RGBHV, RGBS  
Input level ..................................... 3.5 V to 5.5 Vp-p, unterminated  
Input impedance .......................... 510 ohms  
Max. input voltage........................ 5.5 Vp-p  
Video — composite video (CV models)  
Gain ................................................ Unity  
Differential phase error ............... <1.0º at 3.58 MHz and 4.43 MHz  
Differential gain error .................. <1.0% at 3.58 MHz and 4.43 MHz  
Video input — composite video (CV models)  
Number/signal type..................... 1 composite video  
Connectors .................................... 1 female RCA  
Nominal level ................................ 1 Vp-p for composite video  
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset  
PVT Series (Rack Mount Models) • Reference Material  
A-2  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Impedance ..................................... 75 ohms  
Return loss ..................................... <-30 dB @ 10 MHz  
DC offset (max. allowable)........... 100 mV  
Video output — composite video (CV models)  
Number/signal type..................... 1 analog proprietary signal  
Connectors .................................... 1 female RJ-45  
Sync — composite video (CV models)  
Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM  
Audio input  
Number/signal type..................... 1 stereo, unbalanced (2 for PVT SW RGB)  
Connectors  
RGB models ....................... (1) 3.5 mm mini audio jack (tip, ring,  
sleeve), (2 for PVT SW RGB)  
CV models.......................... 1 pair female RCA  
Impedance ..................................... >10k ohms unbalanced, AC coupled  
Nominal level ................................ -10 dBV (316 mVrms)  
Maximum level ............................. +11 dBV, (unbalanced) at 1% THD+N  
N
0 dBu = 0.775 Vrms, 0 dBV =1 Vrms, 0 dBV 2 dBu  
Audio output to a PVS 204SA  
Number/signal type .................... 1 analog proprietary signal  
Connectors .................................... 1 female RJ-45  
General  
External power supply................. Remote power from PVS 204SA  
Power input requirement............. 5 VDC, TBD A  
Rack mount  
PVT CV  
PVT RGB  
PVT SW RGB  
PVT RGB CV...................... Yes, with optional 1U rack shelf,  
part # 60-190-01, or Versa Tools rack shelf,  
part # 60-190-02 or 60-604-20.  
Furniture mountable with optional  
part # 70-212-01  
Enclosure type .............................. Metal  
PVT Series (Rack Mount Models) • Reference Material  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A-3  
Reference Material, cont’d  
Enclosure dimensions  
PVT CV  
1/8 rack Versa Tools.... 1.7" H x 2.2" W x 3.0" D  
4.3 cm H x 5.6 cm W x 7.6 cm D  
PVT RGB, PVT SW RGB, PVT RGB CV  
1/4 rack Versa Tools.... 1.7" H x 4.3" W x 3.0" D  
4.3 cm H x 10.9 cm W x 7.6 cm D  
(Depths excludes connectors.)  
Product weight .............................. 1 lbs (0.5 kg).  
Shipping weight ............................ 2 lbs (1 kg)  
Vibration ........................................ ISTA 1A in carton  
(International Safe Transit Association)  
Listings............................................ UL, CUL  
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES  
MTBF............................................... 30,000 hours  
Warranty ........................................ 3 years parts and labor  
N
N
All nominal levels are at 10%.  
Specifications are subject to change without notice.  
Part Numbers  
Item  
Part number  
60-827-01  
PVT CV  
PVT RGB  
60-821-01  
PVT RGB CV  
PVT SW RGB  
60-828-01  
60-826-01  
Included Parts  
Included parts  
Replacement  
part number  
Tweeker (small screwdriver)  
Rubber feet  
User’s manual  
PVT Series (Rack Mount Models) • Reference Material  
A-4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
   
Optional Accessories  
Item  
Part number  
70-212-01  
70-367-01  
60-190-20  
60-604-20  
60-190-01  
60-604-01  
60-111-01  
26-569-xx  
26-570-xx  
26-637-35  
26-637-50  
26-637-75  
26-637-100  
MBU 123, under desk mounting kit  
MBB 100, back of rack mounting kit  
RSF 123, 3.5" deep rack shelf mounting kit  
RSB 123, 3.5" deep basic rack shelf mounting kit  
RSU 129, 9.5" deep rack shelf mounting kit  
RSB 129, 9.5" deep basic rack shelf mounting kit  
KP 6 Keyboard remote control  
Enhanced Skew-Free A/V UTP cables  
Enhanced Skew-free A/V UTP cables-plenum  
CAT 5 cable, 35', plenum  
CAT 5 cable, 50', plenum  
CAT 5 cable, 75', plenum  
CAT 5 cable, 100', plenum  
A-5  
PVT Series (Rack Mount Models) • Reference Material  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Reference Material, cont’d  
This page was deliberately left blank.  
PVT Series (Rack Mount Models) • Reference Material  
A-6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FCC Class A Notice  
Note: This equipment has been tested and found to comply with the limits for a  
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses and can radiate  
radio frequency energy and, if not installed and used in accordance with the instruction  
manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference, in which case the  
user will be required to correct the interference at his own expense.  
Note: This unit was tested with shielded cables on the peripheral devices. Shielded  
cables must be used with the unit to ensure compliance.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following  
two conditions: (1) this device may not cause harmful interference, and (2) this device  
must accept any interference received, including interference that may cause undesired  
operation.  
Extron’s Warranty  
Extron Electronics warrants this product against defects in materials and workmanship  
for a period of three years from the date of purchase. In the event of malfunction during  
the warranty period attributable directly to faulty workmanship and/or materials,  
Extron Electronics will, at its option, repair or replace said products or components,  
to whatever extent it shall deem necessary to restore said product to proper operating  
condition, provided that it is returned within the warranty period, with proof of  
purchase and description of malfunction to:  
USA, Canada, South America,  
and Central America:  
Extron Electronics  
Europe, Africa, and the Middle East:  
Extron Electronics, Europe  
Beeldschermweg 6C  
1001 East Ball Road  
3821 AH Amersfoort  
Anaheim, CA 92805, USA  
The Netherlands  
Asia:  
Japan:  
Extron Electronics, Asia  
135 Joo Seng Road, #04-01  
PM Industrial Bldg.  
Singapore 368363  
Extron Electronics, Japan  
Kyodo Building,  
16 Ichibancho  
Chiyoda-ku, Tokyo 102-0082  
Japan  
This Limited Warranty does not apply if the fault has been caused by misuse, improper  
handling care, electrical or mechanical abuse, abnormal operating conditions or non-  
Extron authorized modification to the product.  
If it has been determined that the product is defective, please call Extron and ask for an  
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400  
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This  
will begin the repair process as quickly as possible.  
Units must be returned insured, with shipping charges prepaid. If not insured, you  
assume the risk of loss or damage during shipment. Returned units must include the  
serial number and a description of the problem, as well as the name of the person to  
contact in case there are any questions.  
Extron Electronics makes no further warranties either expressed or implied with respect  
to the product and its quality, performance, merchantability, or fitness for any particular  
use. In no event will Extron Electronics be liable for direct, indirect, or consequential  
damages resulting from any defect in this product even if Extron Electronics has been  
advised of such damage.  
Please note that laws vary from state to state and country to country, and that some  
provisions of this warranty may not apply to you.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Extron Electronics, USA  
1230 South Lewis Street  
800.633.9876 714.491.1500  
FAX 714.491.1517  
Extron Electronics, Europe  
Beeldschermweg 6C  
+800.3987.6673 +31.33.453.4040  
FAX +31.33.453.4050  
Extron Electronics, Asia  
135 Joo Seng Rd. #04-01  
+800.7339.8766 +65.6383.4400  
FAX +65.6383.4664  
Extron Electronics, Japan  
Kyodo Building, 16 Ichibancho  
Japan  
+81.3.3511.7655 FAX +81.3.3511.  
© 2007 Extron Electronics. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Ericsson Network Router W3X User Manual
Exmark Lawn Mower CD42CD User Manual
Fiesta Gas Grill ESD45055 B327 User Manual
Frigidaire Refrigerator FFHS2622 User Manual
Fujitsu Printer FTP 608 Series User Manual
Fusion Car Amplifier RE AM45020 User Manual
Garmin GPS Receiver 21 FM TMC User Manual
GE Clothes Dryer DCVH660GH User Manual
Gefen Switch 4x4 DVI Matrix User Manual
GE Network Router IS200ADIIH_A_ _ User Manual