User’s Manual
YCS 100
Composite Video and S-video Transcoder
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
68-495-10 Rev. A
06 06
© 2006 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
电源 • 该设备只能使用产品上标明的电源。 设备必须
使用有地线的供电系统供电。 第三条线（地线）是
安全设施，不能不用或跳过 。
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设
备后或桌面电源的电源线，或任何接到市电系统的
电源线。
这个符号警告用户该设备机壳内有
露的危险电压，有触电危险。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
维护 • 所有维修必须由认证的维修人员进行。 设备内
部没有用户可以更换的零件。为避免出现触电危险
不要自己试图打开设备盖子维修该设备。
注意
阅读说明书 • 用户使用该设备前必须阅读并理解所有
安全和使用说明。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来
防止机内敏感元件过热。 不要用任何东西挡住通
风孔。
保存说明书 • 用户应保存安全说明书以备将来使用。
遵守警告 • 用户应遵守产品和用户指南上的所有安全
和操作说明。
锂电池 • 不正确的更换电池会有爆炸的危险。必须使用
与厂家推荐的相同或相近型号的电池。按照生产厂
的建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或追
加设备，以避免危险。
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter One • Introduction ................................................... 1-1
About this Manual .................................................................... 1-2
About the YCS 100.................................................................... 1-2
Features ........................................................................................ 1-2
Application Diagram................................................................. 1-3
Chapter Two • Installation and Operation ................. 2-1
Installation Overview............................................................... 2-2
Mounting the YCS 100............................................................. 2-2
Tabletop use........................................................................... 2-2
Rack mounting....................................................................... 2-2
Mounting on a rack shelf ............................................... 2-2
Back of the rack mounting .............................................. 2-4
Furniture mounting ............................................................... 2-6
Projector mounting................................................................ 2-7
Using the PMK 100 Mini Projector Mount Kit................ 2-7
Using the PMK 300 Projector Mount Kit ........................ 2-8
Using the PMK 350 Projector Mount Kit ...................... 2-10
Rear Panel .................................................................................. 2-12
Wiring the Power Connector............................................... 2-13
Operation................................................................................... 2-14
Troubleshooting....................................................................... 2-15
Problem: No video input ..................................................... 2-15
Appendix A • Specifications, Part Numbers, and
Accessories ........................................................................................A-1
Specifications..............................................................................A-2
Included Parts .............................................................................A-5
Accessories...................................................................................A-5
All trademarks mentioned in this manual are the properties of their respective owners.
68-495-10 Rev. A
06 06
YCS 100 • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
YCS 100
Chapter One
1
Introduction
About this Manual
About the YCS 100
Features
Application Diagram
ii
YCS 100 • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Quad standard compatibility — The digital quad standard
About this Manual
decoder and encoder provide for universal compatibility.
This manual contains information about the Extron
Enclosure — The YCS 100 has a compact 1U high, ¼-rack wide,
3 inches deep Versatools® metal enclosure that can be
easily placed or mounted in a variety of locations.
YCS 100 Transcoder, and discusses how to install, configure, and
operate it.
The terms “YCS 100,” “YCS,” and “transcoder” are used
interchangeably throughout this manual.
Power supply — An external 12 VDC power supply with a
two-pin captive screw connector accepts 100 to 240 VAC.
The power supply input has single diode polarity
protection.
About the YCS 100
The Extron YCS 100 Transcoder has a composite video to
S-video (luminance [Y] and chrominance [C]) decoder and an
S-video to composite video encoder in one product. The high
performance digital decoder has a time base stabilizer that
corrects the jitter from VCR signals. A 5-line adaptive comb
filter performs the Y/C separation, virtually eliminating chroma
noise. Each input has its own individually buffered loop-
through signal.
Rack, furniture, and projector mounting — The YCS 100 can be
mounted on a rack shelf, under a desk or podium, or on a
projector pole, with an optional mounting kit.
Application Diagram
The following diagram provides an example of how the YCS 100
may be connected.
The transcoder is compatible with NTSC 3.58, NTSC 4.43,
SECAM, and PAL standards.
Cable Box
Composite
Features
Digital decoding and analog encoding — The YCS 100 digitally
decodes (separates) the composite video input signal
into Y and C for S-video. It provides analog encoding
(combining) of the Y and C signals of S-video input into
composite video.
DSS Receiver
S-video
0
0
1
S
C
Y
DER
IN
ENCO
Extron
YCS 100
Video Encoder
and Decoder
R
DECODE
P
LOO
OUT
IN
WER
OUT
PO
X
V
A
2
1
0
M
A
.3
LOOP
Time base stabilizer — The time base stabilizer (TBS) stabilizes
the video signal in the time domain. This results in a
significantly more stable image on the screen and better
recording quality from input sources with unstable video
signals, such as consumer VCRs and worn or multi-
generation VHS tapes.
Monitor
S-video
VCR
Composite
Monitor
S-video
VCR
Composite
Input connectors — The decoder has one composite video
input on a female BNC connector. The decoder input
is buffered and looped through, also on a female BNC
connector.
Figure 1-1 — YCS 100 connection diagram
The encoder has one S-video input on 4-pin mini DIN
connectors. The encoder input is buffered and looped
through, also on a 4-pin mini DIN connector.
Output connectors — The decoder has one S-video output
on a 4-pin mini DIN connector. The encoder has one
composite video output on a BNC connector.
YCS 100 • Introduction
YCS 100 • Introduction
1-2
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
YCS 100
Chapter Two
2
Installation and Operation
Installation Overview
Mounting the YCS 100
Rear Panel
Wiring the Power Connector
Front Panel
Operation
Troubleshooting
YCS 100 • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
3.
Install blank panel(s) or other unit(s) on the rack shelf as
desired.
Installation Overview
To install and set up the YCS 100, follow these steps:
Mount the YCS 100 on a rack shelf, furniture, or projector
bracket if desired.
1
VersaTools Rack Shelf
Connect your input and output devices to the YCS 100’s
rear panel connectors.
2
3
Wire the provided 2-pin captive screw connector to the
external power supply. (See Wiring the Power Connector,
later in this chapter.)
Apply power to the YCS 100 and to the input and output
devices.
4
1/4 Rack Width Front
False Faceplate
Mounting the YCS 100
The YCS 100 can be set on a table; mounted on a rack shelf;
mounted under a desk, podium, or table; or attached to a
projector with one of the Extron projector mounting kits.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Tabletop use
Figure 2-1 — Mounting a YCS 100 (with other units)
on a VersaTools rack shelf
Four self-adhesive rubber feet are included with the YCS 100.
For tabletop use, attach one foot at each corner on the bottom of
the unit, and place the YCS in the desired location.
Rack mounting
1U Universal Rack Shelf
1/2 Rack Width Front False
Faceplate
For optional rack mounting, do not install the rubber feet.
Mount the transcoder on one of the following rack shelves:
1/4 Rack Width Front False
Faceplate
•
•
•
1U 3.5" Deep VersaTools® rack shelf
Standard (RSF 123, part #60-190-20) or Basic (RSB 123, part
#60-604-20)
1U 9.5" Deep rack shelf
Universal (RSU 129, part #60-190-01) or Basic (RSB 129,
part #60-604-01)
Both front false faceplates
use 2 screws.
1U 6" Deep Rack Shelf
Universal (RSU 126, part #60-190-10) or Basic (RSB 126,
part #60-604-10)
Mounting on a rack shelf
1.
If feet were previously attached to the bottom of the YCS,
remove them.
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
2.
Mount the YCS 100 on the rack shelf, using two
4-40 x 3/16" screws in opposite (diagonal) corners to
secure the unit to the shelf (see figures 2-1 and 2-2, on the
next page, or figure 2-3 on page 2-4).
Figure 2-2 — Mounting a YCS 100 on a standard
rack shelf
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-2
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
6" Deep Rack Shelf
1/2 Rack Width Front False
Faceplate
Front false
faceplate
uses 2
screws.
(2) 4-40 x 3/16"
Screws
Figure 2-4 — Attaching the back of rack mounting
brackets to the YCS 100
Use 2 mounting holes on
opposite corners.
Figure 2-3 — Mounting a YCS on a 6-inch rack shelf
5.
Mount the unit to the rack support, using the two included
rack screws (see figure 2-5, below).
Back of the rack mounting
The YCS 100 also can be mounted vertically to the front or rear
rack supports, using the optional MBB 100 back of the rack
mounting kit (Extron part #70-367-01).
.
12V
P
WER
R
R
Follow these steps to mount the YCS to the rack supports using
the back of the rack mounting kit:
O
INPUT
1.
2.
3.
If feet were previously attached to the bottom of the YCS,
remove them.
1
Remove the two screws from one side of the YCS. Retain
the screws for possible later reassembly.
L
1
A
U
2
L
DI
P
O
I
U
T
S
R
T
3
L
S
R
M
L
S
L
1
4
0
3
R
A
V
U
X
M
M
/
N
I
O
TP
O
P
U
P
T
R
L
EA
M
D
R
H
5
M
L
P
C
O
/R
W
E
1
S
-2
R
32
0
0
1
U
L
E
A
B
1
Q
E
S
2
B
V
1
.5
N
E
A
M
L
2
A
1
X
R
A
E
U
2
L
DI
P
R
G
U
S
R
U
T
3
L
S
R
M
L
S
1
4
0
D
E
3
R
A
V
U
X
M
M
/
N
I
O
U
O
T
P
P
U
T
R
R
L
EA
M
P
R
Attach one bracket to the side of the unit, using the longer
screws included in the mounting kit (see figure 2-4, on the
next page).
M
L
P
C
O
/R
W
S
-2
R
32
E
12
A
V
B
.5
A
M
A
X
L
1
R
A
U
L
DI
S
O
2
U
N
T
S
R
U
T
3
L
M
R
L
S
L
1
4
0
3
R
A
V
U
X
M
/
N
I
X
U
O
T
O
P
P
U
T
R
L
EA
M
P
R
M
L
P
C
O
/R
W
S
-2
R
3
2
E
1
O
U
4.
Repeat steps 2 and 3 on the other side of the YCS.
T
1
A
P
2
2
B
V
U
T
1
.5
A
M
A
X
3
1
O
U
T
P
2
U
T
2
3
M
M
X
3
2
V
G
A
A
Figure 2-5 — Mounting the YCS 100 to a back rack
support
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-4
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Furniture mounting
Projector mounting
To furniture-mount the YCS 100, use the optional MBU 123
VersaTools under-desk mounting kit (part #70-212-01), as
follows.
To projector-mount the YCS 100, use one of the three optional
mounting kits described in the following sections.
Using the PMK 100 Mini Projector Mount Kit
1.
2.
3.
If rubber feet were previously attached to the bottom of the
unit, remove them.
The PMK 100 is a projector mounting kit (part # 70-217-01)
designed for use with Extron 1U high, quarter-rack width
products like the VersaTools products. It allows them to be
mounted near or on a projector support.
Remove the two screws from one side of the YCS. Retain
the screws for possible later reassembly.
Attach one bracket to the side of the unit, using the
provided machine screws (see figure 2-6, below).
Follow these steps to projector-mount the YCS 100 using the
PMK 100 kit:
1.
2.
3.
If rubber feet were previously attached to the bottom of the
unit, remove them.
Remove the two screws from one side of the YCS. Retain
the screws for possible later reassembly.
Attach the projector mounting bracket to the side of the
unit, using the provided machine screws.
Mounting
Bolt
Projector
Mounting
Bracket
Figure 2-6 — Preparing the YCS 100 for under-desk
mounting
4.
5.
Repeat steps 2 and 3 on the other side of the YCS.
Ceiling
Hold the unit with the attached brackets against the
underside of the table or other furniture. On the mounting
surface, mark the location of the bracket’s screw holes.
Projector
6.
7.
Drill 3/32" (2 mm) diameter pilot holes, ¼" (6.3 mm) deep
in the mounting surface at the marked screw locations.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than ¼" of the screw head protrudes.
Figure 2-7 — Projector-mounting the YCS 100 using
the PMK 100 Projector Mount kit
8.
9.
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
4.
Secure the unit to a projector mount or other surface by
inserting the mounting bolt through the bracket’s slotted
hole.
Slide the unit slightly forward or back, then tighten all four
screws to secure it in place.
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-6
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
•
For the YCS 100 unit, use two of the supplied
4-40 x 3/16" screws in opposite (diagonal) corners to
secure the device to the bracket.
Using the PMK 300 Projector Mount Kit
The PMK 300 Multi-Product Projector Mount Kit (#70-374-01)
mounts up to three quarter-rack width products to a projector
ceiling mount pole. The YCS 100 can be mounted above the
display device with the front panel facing either down or up.
The quarter rack width plate can also be used to mount the YCS
external desktop power supply.
For the YCS power supply, use the two included tie
wraps to strap the power supply to the bracket.
The PMK 300 has a hole in the bottom plate that allows
the projector pole to be inserted through the center of
the plate, rather than outside of the plate (see figure 2-9,
below). To install the PMK 300 in this configuration,
slide the bracket up from the bottom of the pole before the
projector is installed on the pole.
N
Follow these steps to projector-mount the YCS 100 using the
PMK 300:
1.
2.
If necessary, remove the feet from the bottom of the YCS.
Mount the YCS to one of the bracket’s three mounting
plates. It can be vertically mounted facing either up or
down, whichever you prefer. See figure 2-8, below.
Bracket
Brace
Bracket
Brace
U-Bolt
Extron
PMK 300
Multi-product Projector
Mount Kit
U-Bolt
Extron
PMK 300
Multi-product
Projector
Mount Kit
Figure 2-8 — Projector-mounting the YCS 100 using
the PMK 300 Projector Mount Kit
Figure 2-9 — Projector-mounting the YCS 100
using the PMK 300 with the projector pole passing
through the center
•
On the side mounting plates, the YCS is typically
mounted on the outside of the bracket.
On the front mounting plate, the device is typically
mounted on the inside of the bracket.
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-8
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
3.
4.
Affix the supplied rubber pad to the side of the U-bolt
clamping plate that the projector pole contacts.
Extron
YCS 100
Transcoder
Place the U-bolt around the ceiling pole and insert the two
legs of the U-bolt through the slotted holes on the bracket’s
mounting plate, then through the round holes on the
backing brace.
Rear Plate
Contoured
Base
•
For a typical (1.5" to 2.0" diameter) pole — You can use
the supplied square U-bolt, which fits a typical ceiling
pole.
L-shaped
Bracket
Extron
PMK 350
Multi-product Projector
Mounting Kit
U-bolt
•
For a smaller or larger pole — Locally obtain a square
U-bolt that fits your ceiling pole. The slotted holes on
the bracket can accommodate a square U-bolt for pole
sizes from 1.0" to 2.5" in diameter.
Extron
Power Supply
5.
Secure the bracket to the U-bolt with the included hex
nuts, washers, and lock washers. Tighten the hex nuts just
enough that they can be loosened by hand.
Front Plate
Using the PMK 350 Projector Mount Kit
Cover Sheet
The PMK 350 Low Profile Projector Mount Kit is an above-
projector mounting kit that attaches to a 1" to 2" diameter
projector mounting pole. It can hold more than one device,
in a variety of sizes. The PMK 350 is available in black
(part #70-563-02) or white (part #70-563-03).
Figure 2-10 — Projector-mounting the YCS 100
using the PMK 350 Projector Mount Kit
7.
Align the two slotted holes in the bottom of the L-shaped
bracket with the two slotted holes in the base of the
PMK 350, on either side of the opening for the pole.
Attach the L-bracket to the base by inserting two provided
6-32 x 5/16" screws through the aligned slots.
Follow these steps to mount the YCS 100 on the PMK 350
bracket as follows:
1.
Remove the front and back panels from the
PMK 350, using an Extron Tweeker or other small Philips
screwdriver. (Retain the screws to reattach the plates when
you are finished.)
8.
Insert the two legs of the provided square U-bolt through
the following parts in the order they are listed below:
a. The slotted holes on the back side of the bracket mount
2.
3.
Remove any rubber feet from the bottom of the YCS 100.
plate
Secure the YCS to one side of the mounting bracket,
using two of the supplied 4-40 x 3/16" screws in opposite
(diagonal) corners.
b. The round holes in the rubberized contour base
c. The round holes in the L-shaped bracket
•
For a typical (1.5" to 2.0" diameter) pole — You can use
the supplied square U-bolt, which fits a typical ceiling
pole.
4.
5.
6.
Using the two included tie wraps, strap the YCS power
supply to the PMK 350 bracket.
Place the bracket around the projector ceiling mounting
pole as shown in figure 2-10.
•
For a smaller pole — Locally obtain a square U-bolt
that fits your ceiling pole. The slotted holes on the
bracket can accommodate a square U-bolt for pole sizes
from 1.0" to 2.0" in diameter.
Place the rubberized contoured base against the pole and
opposite the back plate. The pole should fit snugly into the
depression in the center of the contoured base.
9.
Move the PMK 350 up to the desired location on the ceiling
pole, as close to the ceiling as desired.
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-10
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
10. Secure the L-shaped bracket to the square U-bolt using the
7
Power connector — Plug the external 12 VDC power supply
into this 2-pin, 3.5 mm captive screw connector.
included hex nuts, washers, and lock washers. Tighten the
hex nuts securely.
Be sure to tighten the hex nuts securely enough that the
PMK 350 does not slide down the ceiling pole. A socket
wrench is recommended to tighten the hex nuts.
N
Wiring the Power Connector
To wire the connector for the external power supply,
1.
2.
Cut the DC output cord to the length needed.
11. Secure the front panel to the mounting tray with four of
the included #6 screws.
Strip the jacket to expose 0.2 inches (5 mm) of the
conductors.
12. If desired, choose one of the provided four sizes of self-
adhesive cover sheets, and apply it to the underside of the
mounting tray.
Exposing more than 0.2" (5 mm) of the copper
wires could allow the stripped wires to touch each
other, causing a short circuit. This could result in
the external DC power supply overheating and/or
burning.
C
Rear Panel
2
1
Stripping the wires to expose less than the
recommended amount may cause them to slide out
of the connector too easily, even if they are tightly
pinched by the captive screws.
DECODER
ENCODER
IN
YCS 100
IN
12V
0.3A MAX
3.
Slide the leads into the supplied 2-pin captive screw plug
and secure them, using an Extron Tweeker or other small
screwdriver.
LOOP
OUT
OUT
LOOP
4.
5.
Use the supplied tie wrap to strap the power cord to the
extended tail of the connector.
7
6
5
4
3
To verify the power cord’s polarity before connecting
it, plug in the power supply with no load and check the
output with a voltmeter.
Figure 2-11 — YCS 100 rear panel
Figure 2-12 shows how to wire the connector.
The YCS 100 rear panel contains the following features:
1
2
3
Input composite video connector (decoder) — Connect a
composite video input source to this BNC connector.
Smooth
Ridges
Input S-video connector (encoder) — Connect an S-video input
source to this 4-pin mini-DIN connector.
A
A
SECTION A–A
S-video loop-through connector (encoder) — Connect a
monitor or other deviceto this 4-pin mini-DIN loop-through
connector.
Power Supply
Output Cord
Tie Wrap
0.2” (5 mm) MAX
4
5
6
Composite video output connector (encoder) — Connect a
composite video display device to this BNC connector.
S-video output connector (decoder) — Connect an S-video
display device to this female 4-pin mini-DIN connector.
Orange Captive Screw
Connector
Composite video loop-through connector (decoder) — Connect
a monitor or other device to this BNC loop-through connector.
Figure 2-12 — Power connector wiring
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-12
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
Your YCS may have been shipped with a blue captive
screw connector. This blue connector can be plugged
into either a blue or an orange power receptacle.
N
Troubleshooting
Possible problems and their solutions include the following:
Problem: No power at unit
The blue connector does not have the extended tail or the
included tie-wrap.
Solution: Verify that the unit is receiving power by checking the
front panel LED. If the LED is not lit, check the DC power
plug termination and polarity.
Do not tin the stripped power supply leads before
attaching the captive screw plug to them. Tinned
wires are not as secure in the captive screw
connectors and can be easily pulled out. They may
also break after being bent several times.
C
Problem: No video input
Solution: Verify that the source and output devices are powered
on and connected properly.
Front Panel
Problem: Black and white image flashes or scrolls
rapidly
Cause: When a black and white signal is used without a
colorburst signal, the output image may not sync correctly,
causing continual flashing and rapid scrolling of the black
and white image.
1
Solution: Close (enable) the jumper located at CR8 on the
YCS 100 internal board. This corrects the black and white
picture settings for NTSC and PAL standards.
YCS 100
VIDEO DECODER/ENCODER
Figure 2-13 — YCS 100 front panel
When you are not using a black and white signal, set the
jumper back to the open position (the default).
N
The YCS 100 front panel contains the following:
Follow these steps to enable the jumper:
1
Power LED indicator — This green LED lights when the
YCS 100 is receiving power.
1.
Disconnect all power to the YCS and any attached devices.
If the YCS is mounted, remove it from its mounting.
2.
Remove the YCS cover by removing the two screws on
each side and lifting the cover up and off.
Operation
When the transcoder, input sources, and display devices are
Lift cover
straight up.
powered up, the system is fully operational. During YCS 100
operation, one or both of the following takes place:
•
The YCS 100 digital decoder accepts a composite video
signal and separates it into Y (luma) and C (chroma),
converting the signal to output S-video, while also
passing an unconverted signal to a composite video
monitor attached to the video loop-through BNC
connector.
Remove (4)
screws from
sides.
•
The YCS 100 analog encoder accepts an S-video signal
and converts it to composite video while also passing an
unconverted signal to an S-video monitor connected to
the S-video mini DIN loop-through connector.
Figure 2-14 — Removing the cover of the YCS 100
3.
Locate the two-pronged CR8 jumper near the center back
of the YCS board. (See the photograph below.)
If problems are encountered, ensure that all cables are routed
and connected properly.
YCS 100 • Installation and Operation
YCS 100 • Installation and Operation
2-14
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation, cont’d
YCS 100
Appendix A
A
Figure 2-15 — Jumper on YCS 100 internal board
When the YCS is delivered from the factory, a shunt is
attached to one prong of the jumper. This shunt is used
to enable the jumper in step 4.
N
4.
Enable (close) the CR8 jumper by placing the shunt on both
prongs, as shown below.
Specifications, Part Numbers,
and Accessories
Specifications
Included Parts
Accessories
Open
Closed
Figure 2-16 — Enabling the CR8 jumper
5.
6.
Replace the YCS cover, using the screws that you removed.
Connect and power on all attached devices, then power on
the YCS 100.
YCS 100 • Installation and Operation
2-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
Nominal level ................................ 1 Vp-p for composite video (including
sync)
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p for composite
video with no offset at unity gain
Specifications
The YCS 100 includes a built-in S-video decoder and a
composite video encoder. The encoder portion and the decoder
portion are independent and may be used simultaneously.
N
Impedance ..................................... 75 ohms
Return loss ..................................... -34 dB for composite video @ 5 MHz
Input coupling............................... Decoder input: AC coupled
Loop-through input: DC coupled
Video — encoder portion
Gain ................................................ Unity
Standards........................................ NTSC 3.58, NTSC 4.43, PAL (B, G, H, I,
D, N, M), SECAM (B, G, H, D, K, K1, L);
autodetected
Video — decoder portion
Gain ................................................ Unity
Standards........................................ NTSC 3.58, NTSC 4.43, PAL (B, G, H,
I, D, N), SECAM (B, G, H, D, K, K1, L);
autodetected
Video input and loop-through — encoder portion
Number/signal type..................... 1 S-video, 1 S-video loop-through
Connectors ..................................... 1 female 4-pin mini DIN (input), 1 female
4-pin mini DIN (loop-through)
Nominal level ................................ 1 Vp-p for Y of S-video (including sync)
0.3 Vp-p for C of S-video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p for Y with no
offset at unity gain
Impedance ..................................... 75 ohms
Return loss ..................................... -27 dB for Y, -31 dB for C @ 5 MHz
Input coupling............................... AC coupled
Video processing — decoder portion
Signal processing type.................. Digital decoding
Digital sampling............................ 10 bits per color, 30 bits total; 14.3 MHz
sampling frequency
Colors.............................................. 1 billion
Decoder type.................................. Adaptive 2D, 5-line digital comb filter
Video output — decoder portion
Number/signal type..................... 1 S-video
Connectors ..................................... 2 female BNC and/or 1 female 4-pin mini
DIN for S-video
Video processing— encoder portion
Signal processing type.................. Analog encoding
Nominal level ................................ 1 Vp-p for Y of S-video (including sync)
0.3 Vp-p for C of S-video
Minimum/maximum levels........ 0.3 V to 1.5 Vp-p for Y, follows input
Impedance ..................................... 75 ohms
Return loss ..................................... -40 dB @ 3.58 MHz
DC offset ........................................ Y: 300 mV with input at 0 offset
C: 600 mV
Video output — encoder portion
Number/signal type..................... 1 composite video
Connectors ..................................... 1 female BNC for composite video
Nominal level ................................ 1 Vp-p for composite video
Minimum/maximum levels........ 0.3 V to 1.5 Vp-p for composite video,
follows input
Impedance ..................................... 75 ohms
Return loss ..................................... -40 dB @ 3.58 MHz
DC offset ........................................ 300 mV with input at 0 offset
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external,
autoswitchable; to 12 VDC, 1 A max.,
regulated
Power input requirements........... 12 VDC, 0.3 A
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Video input and loop-through — decoder portion
Number/signal type..................... 1 composite video input, 1 composite
video loop-through
Connectors ..................................... 1 female BNC (input), 1 female BNC
(loop-through)
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
YCS 100 • Specifications, Part Numbers, and Accessories
YCS 100 • Specifications, Part Numbers, and Accessories
A-2
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Rack mount.................................... Yes, with optional 1U rack shelf, part
#60-190-01 or 60-604-01; 1U, 6” deep rack
shelf, part #60-190-10 or 60-604-10; or
VersaTools® rack shelf, part #60-190-20 or
60-604-20.
Included Parts
These items are included in each order for a YCS 100:
Included parts
Part numbers
to reorder
Above-projector mountable with the
optional PMK 100 Mini Projector Mount
Kit (#70-217-01), the PMK 300 Multi-
Product Projector Mount Kit (#70-374-01),
or the PMK 350 Low Profile Projector
Mount Kit (#70-563-03).
YCS 100 transcoder
60-323-10
12 VDC, 1A external power supply
with U. S. style power cord
70-055-01
2-pin captive screw power plug
YCS 100 User's Manual
Enclosure type .............................. Metal
Enclosure dimensions .................. 1.7” H x 4.3” W x 3.0” D
(1U high, quarter rack wide)
Rubber feet, self-adhesive (4, not attached)
Tweeker (small screwdriver)
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight .............................. 0.4 lbs (0.2 kg)
Shipping weight ........................... 3 lbs (2 kg)
Vibration ........................................ ISTA 1A in carton (International Safe
Transit Association)
Accessories
These items are optional and may be ordered separately:
Listings............................................ UL, CUL
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF............................................... 30,000 hours
Accessories
Part numbers
RSU 129 1U 9.5" Deep Universal rack shelf
RSB 129 1U 9.5" Deep Basic rack shelf
RSU 126 1U 6" Deep Universal rack shelf
RSB 126 1U 6" Deep Basic rack shelf
60-190-01
60-604-01
60-190-10
60-604-10
Warranty ........................................ 3 years parts and labor
All nominal levels are at 10%.
N
Specifications are subject to change without notice.
N
RSF 123 1U 3.5" Deep VersaTools® rack shelf 60-190-20
RSB 123 1U 3.5" Deep VersaTools® rack shelf 60-604-20
MBB 100 Back of the rack mounting kit
MBU 123 Under-desk mounting bracket kit
PMK 100 Mini Projector Mounting Kit
70-367-01
70-212-01
70-217-01
PMK 300 Multi-Product Projector Mounting
Kit
70-374-01
PMK 350 Low Profile Projector Mounting
Kit
70-563-02, -03
26-260-xx
Mini HR cables
S-video cables
26-316-xx
S-video adapters: SVHSM-BNCF, 8” (0.2 m) 26-353-01
YCS 100 • Specifications, Part Numbers, and Accessories
YCS 100 • Specifications, Part Numbers, and Accessories
A-4
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
YCS 100 • Specifications, Part Numbers, and Accessories
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
|