Upright Vacuum Cleaner
Owner’s Guide
Household Type
4650 & 4680 Series
Index
Important Safeguards ................. 2
Service Information ..................... 4
Assembly ................................. 5-6
Thermal Cut Off ....................4 & 7
Use.............................................. 7
Accessories................................. 8
Dirt Alert...................................... 9
Cyclonic Dust Cup ............... 10-11
Brush Roll ................................. 12
Brush Roll Belt .......................... 12
Hose Blockage .......................... 13
Filters ........................................ 14
HEPA Filter................................ 14
Light Bulb .................................. 15
Problem Solving ........................ 17
Warranty.................................... 18
Customer Order Form............... 19
IMPORTANT
Do not return this
product to the store.
For assembly problems or
questions contact: Eureka’s
Customer Service Division toll
free at 1-800-282-2886*, 7 a.m.
to 8 p.m., Central Standard
Time, Monday through
Saturday.
For replacement of broken
or missing items to be
shipped direct to you, call
1-800-438-7352*, 8 a.m. to
4:45 p.m., Central Standard
Time, Monday through Friday.
*En Mexico llame al 5670-6169
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSEILS DE SÉCURITÉ
Lors de l’utilisation d’un appareil électrique, quelques précautions élémentaires doivent être observées, incluant les suivantes:
LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER VOTRE ASPIRATEUR.
AVERTISSEMENT
Pour réduire le risque de feu, de choc électrique, ou de blessure:
• Ne pas utiliser à l’extérieur ou sur des surfaces mouillées.
• Fermez le commutateur et débranchez l’appareil lorsque vous ne l’utilisez pas ou avant le nettoyage ou l’entretien.
• Ne permettez pas qu’il soit utilisé comme jouet. Une attention particulière est nécessaire lorsque utilisé par ou prés d’un
enfant.
• Suivez les recommandations d’utilisation de ce manuel. Utilisez uniquement les accessoires recommandés par le fabriquant.
• Ne pas utiliser si le cordon ou la fiche sont endommagés. Si l’aspirateur ne fonctionne pas comme il le devrait, s’il a été
échappé, s’il est endommagé, s’il a été laissé à l’extérieur ou échappé dans l’eau, retournez-le à un centre de service
avant d’utiliser.
• Ne pas le tirer ou le transporter par le cordon, ne pas utiliser le cordon en guise de poignée. Ne pas fermer une porte sur
le cordon ou tirer le cordon sur des coins ou bordures pointus. Ne pas circuler sur le cordon avec l’aspirateur. Tenir le
cordon à distance des surfaces chauffantes.
• Ne pas utiliser des rallonges ou des prises qui n’ont pas de capacité suffisante pour transporter le courant.
• Fermer tous les contrôles avant de débrancher.
• Ne pas débrancher en tirant sur le cordon. Pour débrancher, tenez la fiche et non le cordon.
• Ne pas manipuler la fiche ou l’aspirateur avec les mains mouillées.
• Ne pas rien insérer dans les ouvertures. Ne pas utiliser si des ouvertures sont bloquées; assurez-vous qu’elles soient
dégagées de poussière, mousse, cheveux ou toute autre chose qui pourrait réduire le passage de l’air.
• Cet aspirateur crée de la succion et contient un rouleau-brosse tournant. Tenir les parties mobiles et les ouvertures loin des
cheveux, du linge, des doigts et de toute partie du corps.
• Ne pas mettre l’aspirateur sur les meubles ou sur les escaliers car le rouleau-brosse peut faire des dommages. Placer
l’aspirateur sur le plancher avec le manche en entreposage position temps que les accessoires sont en usage.
• Ne pas ramasser des objets qui brûlent ou fument comme les cigarettes, allumettes ou cendres chaudes.
• N’utilisez pas sans le coupe de poussière de cyclonique ou filtre(s) en place.
• Les poulies du courroie peuvent devenir chaudes pendant l’utilisation normale. Pour prévenir des brûlures, évitez de
touché la poulie du courroie lorsque vous réparez la courroie.
• Portez une attention particulière lorsque vous nettoyez les escaliers.
• Ne pas utiliser pour ramasser des liquides inflammables ou combustibles comme de l’essence: Ne pas utiliser dans les
endroits où ces liquides pourraient être présents.
• Entreposez votre aspirateur à l’intérieur dans un endroit propre et sec.
• Maintenez un bon éclairage à l’endroit où vous travaillez.
• Débrancher les appareils électrique avant de les balayer.
CONSERVEZ CES INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
To reduce the risk of electric shock, this appliance has a polarized plug (one blade wider than the other). This plug will fit
in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Afin de réduire le risque de choc électrique, cet appareil est muni d’une fiche polarisée (une des lames est plus large).
Cette fiche ne peut être insérée dans une prise polarisée que d’une seule façon. Si la fiche ne peut être insérée dans la prise,
retourner la fiche. Si la fiche ne peut toujours pas être insérée dans la prise, faire installer une prise adéquate par un
électricien qualifié. Ne pas modifier la fiche.
GENERAL INFORMATION
The cleaner is designed to pick up dirt and dust particles. Avoid picking up hard or sharp objects with the cleaner to prevent
hose clogs.
Service Information
The instructions in this booklet serve as a guide to routine maintenance. For additional service information telephone our toll
free number for the nearest Eureka Authorized Warranty Station. You should know the model, type and serial numbers
when you call:
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701,
USA. In Canada write to The Eureka Company, 866 Langs Drive, Cambridge, Ontario N3H 2N7. Refer to The Eureka Limited
Warranty for complete service information.
DO NOT OIL the motor or the brush roll at any time. The bearings are permanently lubricated and sealed.
Rating Plate
The model, type, and serial numbers are indicated on the
MODEL
VOLTS
TYPE
SERIAL NO.
HERTZ
rating plate located on the back side of the cleaner. For
prompt and complete service information, always refer to
these numbers when inquiring about service.
AMPS.
SERVICE INFORMATION: 1-800-282-2886
Model & Type__________________________
Serial No. _____________________________
THE EUREKA COMPANY
BLOOMINGTON, ILLINOIS 61701
Thermal Cut Off
This vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly
shuts off, push the switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as
a full cyclonic dust cup, a blocked hose or clogged filter. If these conditions are found, fix them and wait at least 30 minutes
before attempting to use the cleaner. After the 30 minute period, plug the cleaner back in and turn on the switch. If the cleaner
still does not run, then take it to a Eureka Authorized Service Center for repair.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ASSEMBLE
CAUTION: Assemble the cleaner before using.
CAUTION: Moving parts, make sure on/off switch is in off position before plugging in.
NOTE: Features may vary by model yet all parts assemble the same.
Step B Attach Hose
Step A Attach Handle
CAUTION: Do not catch cord under handle.
3
Button
Hole
1
Groove
Groove
2
4
Hose
Hose Retainer
1. From rear of cleaner, align handle with groove and
slide onto cleaner. If necessary, use thumb and finger
pressure to slide handle into position.
3. From front of cleaner, insert hose adapter into opening
on top of unit. Make sure the button on the hose
adapter is secure in the hole on the unit.
2. Attach handle with two 1 inch screws in the assembly
packet. Use either a slotted or Phillips® head
screwdriver.
4. From back of cleaner, insert the other end of the hose
into the hose retainer.
NOTE: Hand tighten with screwdriver to be sure
both screws are firmly seated.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Step C Store Hose and Accessories
Step D Store Electrical Cord
Optional Dusting Brush and
Upholstery Tool can be
stored in place of the
combination tool on handle
pegs.
5
Cord
Retainer
Handle
Pegs
6
Cord Hook
Combination
Tool
Hook
6
Cord Hook
Crevice
Tool
Carrying
Handle
Extension
Wand or
Wands
HEPA Filter
(on some
models)
5. You will find your cord retainer on the handle above
the upper cord hook. Firmly push the electrical cord
down into the cord retainer. This will place the cord
out of the way the next time you vacuum.
Tabs
6. Next wind the cord around the two cord hooks on
the left side of cleaner.
Hose
Retainer
NOTE: For easier access to dust cup compartment,
when you store the electrical cord use a
figure 8 pattern.
7. Secure the plug to the cord to prevent unwinding.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE
The upright vacuum cleaner design allows use on multiple types of
carpeting and on upholstery or bare floors with attachments. When
using the attachment tools, place the handle in the upright
position. Do not place cleaner on furniture or steps as the brush
roll may cause damage.
1. Adjust cleaner height setting knob to lowest position for maximum
cleaning. Adjust to a higher setting to make pushing easier. For
easy adjustments, tilt the cleaner back to move the knob.
2. Plug electrical cord into outlet.
2
3. Step on handle release. Pull handle back to a comfortable position.
4. Push On/Off power switch.
Store or
Use Attachments
4
ON/OFF
Use
Handle
Release
3
Clean
Under
Handle
Release
3
Cleaner Height Setting
WARNING: Avoid injury. Keep loose clothing, hair,
fingers, and all other parts of body
away from any moving part (such as
the revolving brush). Turn off the
switch and unplug the cleaner before
changing the cleaner height setting.
1
THERMAL CUT OFF
This cleaner has a special thermostat that protects the cleaner
in case of motor overheating. If the cleaner suddenly turns
off, follow this procedure:
The front of the cleaner has an adjustment that raises
or lowers the cleaner base to match the type of carpet.
With the cleaner cord unplugged, set the adjustment
to lowest setting for maximum cleaning. If the cleaner
is difficult to push, move adjustment to next highest
setting until cleaner is comfortable to push. The brush
roll must reach the carpet for effective cleaning.
1. Push on/off pedal once.
2. Unplug cleaner.
3. Check for source of overheating problem (i.e. full cyclonic dust
cup, clogged hose or clogged filter).
NOTE: For ease in moving the adjustment knob,
place handle in operating position and tilt
cleaner back to remove weight from front
wheels.
4. If a full cyclonic dust cup, clogged hose or clogged filter is
found, empty the cyclonic dust cup, unclog the hose or replace
the filters.
5. Wait at least 30 minutes before attempting to reuse the cleaner.
NOTE: When handle is in upright position, brush
roll is lifted off carpet. This is normal. Height
adjustment will not change brush roll level
until the cleaner’s handle is moved into the
operating position.
6. After 30 minute cool down period, plug the cleaner in and push
the switch pedal. The cleaner should turn on.
7. If the cleaner still does not operate, take it to any Eureka
Authorized Service Center for repair.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Dusting Brush is for furniture, blinds, books, lamp shades,
shelves. (On some models.)
How To Use Accessories
NOTE: Do not place cleaner on furniture or
steps as the brush roll may cause
damage. Place cleaner on floor with
the handle in storage position while
using accessories.
Dusting Brush
Depending on which cleaner you purchased, you can
have any combination of the following accessories.
Upholstery nozzle is for curtains, draperies, cushions, fabrics.
(On some models.)
1. Remove hose from rear of cleaner.
2. Place desired accessory onto end of hose or wand.
Always work with the cleaner below you,
pulling hose from side of cleaner; not the back
or the front of the cleaner.
Upholstery
Nozzle
Combination tool gives two types of cleaning tools. (On some
models.)
• Use brush side to dust furniture, blinds, books, lamps, shelves.
• Use upholstery side for curtains, draperies, cushions, fabrics.
Dusting
Side
Upholstery
Side
Crevice tool cleans corners, baseboards, between cushions.
Crevice Tool
Extension wands (Some models use 1 wand)
Nested extension wands to add reach.
.
.
• Grasp both wands near ridges.
• Pull apart.
.
8
• Turn ridge end to center.
• Push wands together.
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance of Dirt Alert Feature (On some models)
The dirt alert sensor uses infra-red technology to indicate whether or not floors are clean. When debris breaks the light
beam, the red light comes on indicating additional cleaning is needed in this area. If there is no break in the light beam, the
floor is clean and no light will come on.
When using your new vacuum you may be cleaning deep down hidden dirt missed by your old vacuum causing the light to
stay red longer. With frequent cleaning, after the first few times you use your new Eureka vacuum, the red light should go on
less.
NOTE: The dirt alert feature is not intended to be used for above the floor cleaning with attachments.
The red light indicates dirt, dust, etc. is still being removed
from the area being cleaned.
How to Check the Dirt Alert Sensors
To check if dirt sensor is working properly.
1. While the red light is on, tip the vacuum backwards on rear
wheels, lifting the brush roll off the carpet a couple of inches.
2. After a few seconds the red light should turn off.
Hose
HINT: New carpeting has loose carpet fibers which will
trip the red light sensor beam.
Infrared
emitter and
sensor
Hose Retainer
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MAINTAIN
The instructions in this booklet serve as a guide to routine maintenance. To avoid unnecessary service calls, check the
cyclonic dust cup, belt, and brush roll often.
To Change Dust Cup Pleated Filter:
NOTE: Turn off the switch and unplug the electrical cord before changing the Foam Filter. Never operate the
vacuum cleaner without the dust cup or the pleated filter assembly.
1
Remove dust cup by pulling latch (1) forward, pivoting dust
cup out and lifting up. To replace dust cup, put bottom of dust
cup in place by aligning tabs in slots and pivot top assembly
back into place. Push down on latch (1), making certain that
latch securely snaps and overlaps tabs at top of dust cup.
Tabs
Slots
Check and clean the pleated filter once a month to maintain good performance. The filter can be cleaned by washing
with mild detergent and warm water. Be sure pleated filter is completely dry before reinstalling.
To clean the Pleated Filter:
1. Grasp yellow filter frame and twist counter clockwise to remove.
2. Shake vigorously and brush off dust and lint.
3. If filter needs further cleaning, wash in warm water using a mild detergent.
4. Do not submerge gray dust cup lid, wipe only with a damp cloth.
5. When all parts are completely dry, replace filter on gray dust lid by twisting clockwise to snap and lock in place.
2
1
Gray Filter
Assembly
Lint Trap
Cone
Use GENUINE EUREKA replacement
pleated filter, 61805
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MAINTAIN (continued)
How To Empty Dust Cup
NOTE: Turn off the switch and unplug the electrical cord before emptying dust cup. Never operate the vacuum
cleaner without the dust cup and filter assembly properly installed.
FOR INSTRUCTIONS ON HOW TO REMOVE THE DUST CUP FROM THE CLEANER
BODY, REFER TO PAGE 10.
Emptying the Dust Cup:
It is clearly visible when the dust compartment is full and needs emptying. Remove dust cup from cleaner body and dump
debris in a waste container.
Reinstalling the Dust Cup:
To mount gray filter assembly into cleaner body, make certain gray filter assembly is fully seated in top of dust cup.
Locate 3 mounting tabs at base of dust cup into slots at front of cleaner. Pivot entire assembly fully into cleaner housing
being certain that gray filter assembly wedges into top of rear housing. Press top cover down to securely latch.
CAUTION: The dust cup can be washed in warm water, if desired, but strong detergents should not be used. Dry thoroughly
before using again. Do not submerge gray filter assembly, wipe only with a damp cloth.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MAINTAIN (continued)
Brush Roll
The brush roll turns as it sweeps and combs the carpet nap.
Remove hair and threads from the brush roll so it continues
brushing the carpet. To maintain the most efficient cleaning,
the bristles must touch the carpet. To test the bristle length,
hold a ruler against the underneath side of the cleaner. If the
bristles no longer touch the ruler, replace the brush roll.
5
Brush Roll Belt
The brush roll belt turns the brush roll to agitate, sweep, and
comb the carpet nap. Check the belt regularly to be sure it is
in good condition. Replace the belt if it stretches, cracks or
loses tension. Cut away any hair or threads wound around the
brush roll or the belt pulley because the buildup could cause
the belt to rotate unevenly.
How To Replace Brush Roll Belt
5. Place new belt around motor shaft.
NOTE: Turn off the switch and unplug the electrical cord
before replacing belt. Belt pulleys can become
hot during normal use. To prevent injury, avoid
touching the motor shaft when checking the belt.
8
6
2
7
1
6. Place belt around brush roll pulley.
7. Align left end cap with base. Push end cap
securely into place.
2
8. Pull right side of brush roll to stretch belt.
Secure right end cap into base.
1. Lower handle to floor to change belt.
2. Loosen, but do not remove, two screws to release hood.
Lift hood to remove.
9
4
Motor
Shaft
Belt
9. Rotate brush roll to seat belt.
10. Replace the hood. Make sure hood front is
behind furniture guard. Hood should seat
onto self-locating screw tabs.
Brush
Roll
3
11. Tighten screws.
Use GENUINE EUREKA replacement belt,
54312. Look for the GENUINE EUREKAproduct
symbol.
3. Lift left end of brush roll.
4. Remove and discard belt.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO MAINTAIN (continued)
How to Clear Hose Clogs
NOTE:Turn off the switch and unplug the electrical
cord before clearing hose.
HoseAssembly
Hose
Adapter
Hose Retainer
3. On the back of the cleaner, pull up on hose assembly to
release from hose retainer.
1. Locate hose adapter on the front of the cleaner.
4. The hose is free of the cleaner. Check for clogs in the
hose retainer and throughout the hose assembly.
5. Use a tool that will not puncture the hose. Clear any debris
from the hose retainer or the hose assembly that could
restrict air flow.
6. Flexing the hose may help loosen the clog.
Button
7. After the clog is removed make sure the hose assembly
is reassembled onto the unit.
s
2. Push button on hose adapter and pull hose upward to
release hose from top of cleaner.
8. If the clog is hard to remove, check the brush roll area.
Remove the hood and clear the hose inlet in the brush
roll area.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor
Adapter
Gasket
HOW TO MAINTAIN (continued)
1
Pre-Motor Filter
Check the pre-motor filter each time the cyclonic dust cup is
emptied. Clean or replace as needed.
Pre-Motor Filter
Motor
Adapter
To Clean Pre-Motor Filter
1. Remove filter centered in the bottom of the dust cup
compartment.
2. Shake filter to remove excess dust. If necessary, the filter
can be cleaned by vacuuming with another cleaner or washing
with mild detergent.
3
3. Reinstall filter after completely dry.
NOTE: If rubber gasket separates from motor adapter,
re-position securely on top edge before using
cleaner.
Use GENUINE EUREKA replacement pre-motor filter, 39348.
HEPACartridge Filters (Only for models with HEPA
HEPA/Micron Filters in Filter Frame
(Only for models with HEPA/Micron filter frame)
cartridge.)
Check the HEPA filters with each disposable dust bag change.
Replace twice a year or after every six bag changes.
Check the HEPA/Micron filter with each disposable
dust bag change. Replace twice a year or after every
six bag changes.
Latch
Filter Frame plus
filter (depending
on your vacuum
model)
Filter cartridge
(One complete unit)
Tabs
To remove HEPA cartridge filters
1. Push down latch and pull filter cassette back.
2. Then lift filter up and remove.
To replace HEPA cartridge filters
1. Place bottom tabs of filter cassette into slots.
2. Rotate filter toward cleaner.
3. Push upward on the latch to secure into place.
To remove HEPA/Micron filters from
filter frame
1. Push down latch and pull filter frame back.
2. Then lift filter up and out of filter frame.
NOTE: To have the benefit of a sealed HEPA system, you must
use one of the HEPA cartridge filter systems.
To replace HEPA/Micron filters into
filter frame
Use GENUINE EUREKA replacement HEPA filter,
60285B.
1. Place new filter in filter frame. Place bottom tabs
of filter frame into slots.
2. Rotate filter frame toward cleaner.
3. Push upward on the latch to secure into place.
Use GENUINE EUREKA replacement filters,
HEPA, part no. 61500; Micron, part no. 60801.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Micron and HEPA Exhaust Filters
(Only for models with the exhaust filter door)
Change micron or HEPA exhaust filter every 3
months.
To Replace Micron or HEPA Exhaust
Filter
Exhaust
Filter
Door
1. Lower the handle. Open exhaust filter door; push
toward the left side.
Micron or
HEPA
Filter
2. Grasp filter and pull out.
3. Push new filter into cleaner, smooth side facing out .
4. Close exhaust filter door; push toward right side.
Exhaust Filter
Door
2
Use GENUINE EUREKA replacement filters, HEPA,
part no. 61505; Micron, part no. 60665.
.
3
HOW TO MAINTAIN (continued)
How To Change Light Bulb (Only for models with
a headlight)
NOTE: Turn off the power switch and disconnect the
electrical cord before changing light bulb.
1. Lower handle. Remove two screws from lens cover.
2. Pull lens cover from cleaner.
3. Pull light bulb and socket toward front.
4. Push light bulb into socket; turn to release.
5. Place new light bulb into socket; turn to secure.
1
6. Push light bulb and socket back so bulb will not touch
lens cover.
7. Replace lens cover.
8. Secure with two screws.
4
Use 15 watt replacement light bulb, part
number 48815.
3
5
15
Download from Www.Somanuals.com. All Manuals Search And Download.
STAIR CLEANING HOSE (Only on Certain Models)
WARNING: Never position any cleaner on the stairs as this could damage the carpet.
Some models will come complete with an extra bonus hose which is ideal for cleaning stairs.
HOW TO ASSEMBLE AND USE
WARNING
Always work with the cleaner below you, pulling
hose from side of cleaner; not the back or the front of
the cleaner. Ensure it is positioned sideways up against
the bottom step.
Step 1 - Remove the hose attached to the cleaner.
Step 2 - Connect the hose cuff to the end of the
bonus hose.
NEVER STAND ANY CLEANER ABOVE YOU.
Step 3 - You are ready to clean your stairs.
NEVER POSITION ANY CLEANER ON THE
STAIRS AS THIS COULD DAMAGE THE CARPET.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM SOLVING
NOTE: Turn off the switch and unplug the electrical cord before servicing.
PROBLEM
CAUSE
SOLUTION
3 Electric Plug
Motor will not start.
Push plug securely into outlet.
Try another outlet.
Check circuit breaker.
3 Thermal Cut Off
Motor suddenly stops.
Refer to page 7.
3
Does not clean the carpet
or floor.
Filters
Clean or replace the filter(s). Hint: If picking up fine
dust, the filter may not look dirty but a fine substance
tends to reduce suction when it blocks the airflow
through the filter(s).
3 Cyclonic Dust Cup
Be sure hose button lock is secure.
Be sure the cyclonic dust cup is properly seated into the
cassette body. See page 10.
Empty cyclonic dust cup. See page 11.
3
3
Belt
Replace a cut, loose or out of shape belt.
Snap the belt cap inside the hood if it comes loose.
Belt Cap
3
Brush Roll
Clean hair and thread from bristles and end cap area.
Replace brush roll if bristles are worn.
3
Hose
Remove any clogs from the hose that restrict the airflow.
Check short hose in the base and long hose. Refer to
page 13.
3
No suction at the end of hose.
Hose Adapter
Be sure button lock on hose adapter is secure.
3
Filter(s)
Clean or replace the filter(s). Hint: If picking up fine
dust, the filter may not look dirty, but a fine substance
tends to reduce suction when it blocks the airflow
through the filter(s).
3 Hose
Remove any clogs from the hose that restrict the
airflow. Check short hose in the base and long
hose. Refer to page 13.
3
Headlight not working.
Light Bulb
Replace light bulb.
3
Noise from the brush roll
area.
Brush Roll
Remove hood and clean debris or items from the brush
roll area.
3
Belt
Replace a cut, loose or out of shape belt.
3
Cleaner is hard to push.
Cleaner Height Setting
Put handle in operating position. Tilt the cleaner back
to raise the front wheels off floor. Then turn the knob to
a higher setting.
3
Belt
Replace a cut, loose or out of shape belt.
3
Cleaner height knob will
not turn.
Cleaner Height
Setting
Hint: Put handle in operating position. Tilt the
cleaner back to raise the front wheels off floor.
Then turn the knob.
3
Dirt Alert red light will not go off.
New carpet fibers.
Over time loose new carpet fibers will diminish and will
not trip the dirt alert sensors.
3
Dirt Alert red light will not come
on.
Dirt sensor is not working.
Call 1-800-282-2886 7 a.m. to 8 p.m. central standard
time, Monday through Saturday for the nearest authorized
Eureka service center.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
THE EUREKA LIMITED WARRANTY
hat This Warranty Covers
W
Your Eureka cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of one year. The warranty is granted only to the
original purchaser and members of his or her immediate household. The warranty is subject to the following provisions.
hat This Warranty Does Not Cover
W
•
•
•
Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brush roll bristles
Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Guide.
Defects or damages caused by unauthorized service or the use of other than Genuine Eureka parts.
hat The Eureka Company Will Do
The Eureka Company will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty. As a matter of warranty policy, the Eureka Company
will not refund the consumer’s purchase price.
W
arranty Registration
W
Please fill out and return the warranty registration card accompanying your cleaner.
btaining Warranty Service
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Eureka Authorized Warranty Station.
You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station is “Eureka Authorized.”
For the location of the nearest Eureka Authorized Warranty Station or for service information, telephone toll free:
O
USA: 1-800-282-2886
Mexico: 5670-6169
Canada: 1-800-282-2886
If you prefer, you can write to The Eureka Company, Service Division, 807 North Main Street, Bloomington, Illinois 61701, USA. In Canada write to The Eureka Company, 866
Langs Drive, Cambridge, Ontario N3H 2N7.
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the Eureka Authorized Warranty Station.
Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type, and serial number from the data plate on the cleaner.
urther Limitations and Exclusions
F
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any warranty for Fitness For AParticular
Purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall Eureka be liable for any consequential or incidental damages you
may incur in connection with your purchase or use of the cleaner. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary by state.
GENUINE
EUREKA PRODUCT
uestions & Answers about Genuine Eureka Products
Q: Why should I use only Genuine Eureka paper bags, belts, and parts in my Eureka vacuum cleaner?
Q
A: Using Genuine Eureka Products, which are made to our exacting specifications and engineered with emphasis on quality, performance, and customer satisfaction,
ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this saves you money and helps to keep your home clean.
Q: How can I be sure I am using only genuine Eureka products in my vacuum cleaner?
A: Typically, packaged products and paper bags can be identified by a “Genuine Eureka Product” symbol (see illustration above). For further identification assistance,
you may call our toll-free number, 1-800-282-2886, for the location of a nearby Eureka Authorized Warranty Station.
Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka paper bags, belts, and parts?
A: Yes, there are some very important differences in materials, quality, and reliability. Many customers have mistakenly purchased “imitation” paper bags and parts
while thinking they purchased genuine. Unfortunately, many of these customers discovered the differences after they experienced related difficulties.
For Genuine Eureka Value, Accept No Imitations!
THE EUREKA COMPANY
Bloomington, Illinois 61701
Household Warranty
abs 190
18
Download from Www.Somanuals.com. All Manuals Search And Download.
10/01
The Eureka Company
P.O. Box 2799
ORDER FORM
Bloomington, IL 61702-2799
VACUUM CLEANERS
(Not applicable in Canada)
Name
Name
S
O
L
S
H
I
Address (street address needed for UPS)
Address (street address needed for UPS)
D
P
City
State
(Eve)
Zip
City
State
Zip
T
O
T
O
Telephone (Day)
(Fax)
Telephone (Day)
(Eve)
(Fax)
IMPORTANT:
Be sure to include
your model, type,
and serial numbers.
These numbers
may be found on
the rating plate.
Part No.
Qty. Price (USD)
Total
Genuine Eureka Bags, Belts and Filters
61120
60285B
61500
60801
61805
39348
2.99
19.99
5.99
Belts (style U) - Extended Life - package of 2
HEPA Filter Cartridge
HEPA Filter Insert (back - style HF3) - package of 2
Micron Filter Insert (back) - package of 2
4.99
Model Number:
Type:
Pleated Filter (style DCF2)
Pre-Motor Filter
12.99
1.09
Serial Number:
To Order
By Phone
1-800-
438-7352*
HOURS:
Accessories/Tools
Nested Wands
58728B
13104-4
61037
4.39
2.49
Call between 8 a.m.
and 4:45 p.m.,
central standard time
Monday through Friday.
Extension Wand
4.49
Combination Tool
Crevice Tool
27237-3
38284-3
54505-3
54785A
54002
2.69
By FAX
1-309-
823-5789
Upholstery Nozzle
Dusting Brush
3.29
5.19
To Answer Problems
or Questions for U.S.A.
and Canada call:
Floor Brush
10.39
12.99
Micro Tool Set for Keyboards
1-800-
282-2886*
Hoses
7 a.m. to 8 p.m.
Deluxe Stretch Hose - with button lock
Stretch Hose - with button lock
Stair Hose - 15 foot
61324-1
61224-1
60166
17.39
11.29
29.99
central standard time
Monday through Saturday.
*En Mexico llame al
5670-6169
By Mail
Brush Rolls
Wood - 15 inch
61308-2
60251-3
12.59
13.89
Simply fill out
this Order Form.
Please be sure to
include day
and evening
phone numbers.
Wood - 12 inch
Miscellaneous Parts
Light Bulb
48815
1.69
Dust Cup
61316-1
25.59
Total (prices subject to change without notice)
Tax (add state tax & local taxes as required by law)
Method of payment (no C.O.D. orders)
Check or money order (payable to The Eureka Company). Do not send currency.
Charge to my
Visa (13/15 digits)
MasterCard (13 digits)
Amer. Express (15 digits)
Postage & Handling Charge (within U.S.A.)
5.50
Acct. number
Signature (full name as shown on acct.)
Expiration Date
TOTAL
© 2001 White Consolidated Industries, Inc.
Printed in U.S.A.
TOTAL ENCLOSED
71081A
Download from Www.Somanuals.com. All Manuals Search And Download.
Questions?
Do Not Return To Store
Call
1-800-282-2886
7 a.m. to 8 p.m., Central Standard Time, Monday through Saturday
Accessory Items in This Carton
1 dusting brush
(on some models)
1 combination tool
(on some models)
1 crevice tool
1 hose assembly
1 upholstery Nozzle
(on some models)
1 hardware package
(2 screws)
1 vacuum cleaner
handle
1 wand
Thank you for selecting a Eureka cleaner.
Don’t Forget to Use
Genuine Eureka Belts
Caution: Damages caused by the use of non-genuine
Eureka parts are not covered by the Eureka Limited
Warranty.
©2000 White Consolidated Industries, Inc.
Part No. 70938B (10/01)
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|