EverFocus
Installation / Operation Instructions
EZ610
Low Light Inline IP66 Bullet Camera
EZ630
Low Light IR Inline IP66 Bullet Camera
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers and
audio speakers since the electromagnetic fields generated from these devices may distort the
video image.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure or
other damage.
3. Try and avoid facing the camera toward the sun.
In some circumstances, direct sunlight or may cause permanent damage to the sensor and/or
internal circuits.
4. Keep the power cord away from water and other liquids and never touch the power cord with
wet hands.
Touching a wet power cord with hands or touching the power cord with wet hands may result in
electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning
Do not touch the surface of the sensor directly with the hands. Use a damp soft cloth to remove
any dirt from the camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Please do not use complex solvents, corrosive or abrasive
agents for cleaning.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings.
Use the camera at temperatures within -40°C ~ 50°C (-40°F~122°F) and in an IP66 complaint
environment; this device is not rated as submersible. The input power source is 12VDC/24VAC.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in
this case, the user may be urged to take adequate measures.
This Product is RoHS compliant.
Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life, should
WEE
be disposed of separately from your household waste.
Please, dispose of this equipment at your local community waste collection/recycling
centre.
In the European Union there are separate collection systems for used electrical and
electronic product.
The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve
his products. Therefore, all specifications are subject to change without prior notice. Misprints reserved.
Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
1
Product Overview..............................................................................................................................................7
1.1 Features ..........................................................................................................................................................7
1.2 Accessory Parts List........................................................................................................................................8
1.3 Specifications ..................................................................................................................................................9
1.4 Dimensions....................................................................................................................................................10
1.5 Camera Component Description ...................................................................................................................11
1.6 Related Products...........................................................................................................................................12
2
3
Installation.......................................................................................................................................................13
2.1 Wiring and Mounting......................................................................................................................................13
2.2 Adjust Camera Position.................................................................................................................................15
OSD Menu Setup.............................................................................................................................................18
3.1 Control Key General Operation Guide...........................................................................................................18
3.2 RS485 ID & Baud Rate Setting .....................................................................................................................19
3.3 OSD Menu Setup ..........................................................................................................................................20
3.3.1 OSD Menu Tree .....................................................................................................................................20
3.3.2 LENS ......................................................................................................................................................21
3.3.3 EXPOSURE............................................................................................................................................22
3.3.3.1 SHUTTER ...............................................................................................................................22
3.3.3.2 AGC (Auto Gain Control – basic low light signal amplification) .....................................................22
3.3.3.3 SENS-UP................................................................................................................................22
3.3.3.4 BLC-Backlight Compensation....................................................................................................23
3.3.3.5 D-WDR ...................................................................................................................................24
3.3.4 WHITE BALANCE CONTROL................................................................................................................24
3.3.5 DAY NIGHT............................................................................................................................................25
3.3.6 3DNR......................................................................................................................................................26
3.3.7 SPECIAL ................................................................................................................................................26
3.3.7.1 CAM TITLE .............................................................................................................................26
3.3.7.2 D-EFFECT ..............................................................................................................................27
3.3.7.3 FREEZE..................................................................................................................................27
3.3.7.4 MIRROR .................................................................................................................................27
3.3.7.5 D-ZOOM .................................................................................................................................27
3.3.7.6 GAMMA ..................................................................................................................................28
3.3.7.7 NEG. IMAGE ...........................................................................................................................28
3.3.7.8 RETURN.................................................................................................................................28
3.3.7.9 MOTION .................................................................................................................................28
3.3.7.10 PRIVACY ..............................................................................................................................28
3.3.7.11 SYNC....................................................................................................................................29
3.3.7.12 LANGUAGE...........................................................................................................................29
3.3.7.13 RETURN ...............................................................................................................................29
3.3.8 ADJUST..................................................................................................................................................29
3.3.8.1 SHARPNESS ..........................................................................................................................29
3.3.8.2 BLUE......................................................................................................................................29
3.3.8.3 RED........................................................................................................................................30
3.3.9 RESET....................................................................................................................................................30
3.3.9.1 FACTORY RESET ...................................................................................................................30
3.3.9.2 EXIT .......................................................................................................................................30
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4
RS-485 Remote Control..................................................................................................................................31
4.1 Remote control with EKB-500 keyboard........................................................................................................31
4.1.1 RS - 485 Wiring ......................................................................................................................................31
4.1.2 OSD Menu Setting by Keyboard ............................................................................................................31
4.1.3 Lens Adjustment by Keyboard................................................................................................................32
4.2 Remote Control with EverFocus DVR ...........................................................................................................32
4.2.1 RS-485 Wiring ........................................................................................................................................32
4.2.2 Camera Operation and Setup by DVR ...................................................................................................32
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
1 PRODUCT OVERVIEW
Amazing color low light sensitivity of 0.05 lux before the added benefits of advanced DSP
technology, delivered by a 1/3” Sony Super HAD II sensor, is just the beginning with the new
EverFocus EZ610/630. Get color without compromise: 560TVL resolution, your choice of full
motion color or true day/night images in low light without ghosting, plus Digital Wide Dynamic
Range to handle the most challenging of bright or unbalanced scene lighting conditions. Where
ambient light levels are too low, select the EZ630 for extended IR range, variable output IR
control to manage illumination and conserve energy, split glass to prevent internal IR reflections.
Easy to mount and install, the camera includes a speedy-mount ring, designed to fit a standard
4” electrical box, for convenient and reliable wall or ceiling mounting; just attach the speedy-
mount ring to the mounting surface and the camera base plate quickly attaches to the ring. A
removeable insert in the ring provides for an on-demand slot for surface wire access. Spin off the
base plate, and the EZ610/630 mates with any standard 1” conduit thread. The E-Z Lock ring at
the base is designed with sure-grip tabs to firmly clamp the camera to the base plate, plus a set
screw in the base provides added security. Vandal resistant, IP66, with motorized varifocal auto
iris lens, dual voltage operation and a full suite of OSD Menu and DSP functions controllable at
the camera or remotely via RS-485 (3D-DNR to save DVR HDD space, privacy masking, 32X
digital zoom, mirroring and rotation, 256X sens-up to a max of .0002 lux, and much more) these
are the cameras you have been waiting for, and might be the only cameras you’ll ever need.
1.1 Features
•
Super HAD II sensor at 0.05 lux has 5X better native light sensitivity before DSP low light
boost
•
Color without compromise: your choice of full motion color or true day/night images in low
light without ghosting
•
•
True Day/Night with ICR module (field selectable, if desired)
Starlight super high sensitivity of 0.0002 Lux/F=1.2 is achieved through a sensitivity
increase setting of up to 256x
•
Extended IR range of up to 60M (196 feet) with 36 LEDs and variable output IR control to
manage illumination and conserve energy (EZ630 model only)
Motorized varifocal auto iris lens – choose 2.8-10mm or 9-22mm focal range
Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright
light sources, deep shadows and/or unbalanced lighting in the same scene
Provides 3D-Noise Reduction to improve picture clarity while enabling DVRs to improve disk
storage utilization
Flexible mounting and positioning – speedy-mount ring also fits a 4” round electrical box; or
remove base to mate with 1” conduit
E-Z Lock ring at the base is designed with easy to grip tabs to firmly clamp the camera in
place, plus a set screw in the base for added security.
•
•
•
•
•
•
•
•
•
•
Easy to use OSD setup menu with local or RS-485 remote control
Motion detection for 4 configurable zones
Privacy mask function for 8 configurable zones
Provides digital zoom up to 32x
Easy bottom access to video test point and lens/OSD menu controls inside a weatherproof
cover
7
Download from Www.Somanuals.com. All Manuals Search And Download.
•
IP66 weather resistant
•
Dual voltage (12VDC/24VAC) with line lock to AC supply
1.2 AccessoryPartsList
Please be careful when you unpack the box and the electronic device inside. Check and
make sure that you have all the items listed below inside the original box:
•
•
•
•
•
•
•
Camera Unit x 1
Speedy Mount Ring x 1
Surface Wire Slot Filler x 1 (optional, may vary in different countries)
Operation Manual x 1
Video Test Cable x 1
Power Supply Pigtail x 1
Mounting Kit x 1
Mounting kit includes:
•
•
•
•
•
•
Long Screws x 4 (for attaching EZ Mount Ring to mounting surface)
Short Screws x 4 (for connecting camera base to EZ Mount Ring)
Expanding Anchors x 4
Hex key x 1 (for adjusting camera)
Hexagon wrench x 1 (for adjusting sunshield and set screw in base)
Mounting Template x 1
Note: If an item appears to have been damaged in shipment, replace it properly in its carton
and notify the shipper. If any items are missing, notify your EverFocus Electronics Corp.
Sales Representative or Customer Service. The shipping carton is the safest container in
which the unit may be transported. Save it for possible future use.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Specifications
EZ610
EZ630
Model
1/3" SONY Super HAD II CCD
NTSC, PAL (by model)
768 x 494(NTSC)/ 752 x 582 (PAL)
560 TVL
Pickup Device
Video Format
Picture Elements
Horizontal Resolution
Sensitivity
0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2
(Sens-up 256x)
0.05Lux/F=1.2 (AGC ON); 0.0002Lux/F=1.2
(Sens-up 256x) ; 0 Lux IR ON
S/N Ratio
Over 52dB (AGC off)
Electronic Shutter
Video Output
1/60(1/50) ~1/100,000
Main Output BNC 1.0V p-p 75Ω,
Local test output, cable provided.
Gamma Correction
Lens Type
0.45
DC Iris Varifocal: focal length 2.8-10mm (MVB) or 9-22mm (MV2) focal length
OFF/BLC/HS BLC Selectable
Back Light Compensation
Auto Gain Control
White Balance
Sync. Mode
Low/Middle/High Selectable
ATW/AWB/AWC/Manual/Indoor/Outdoor Selectable
Internal / Line lock
Day & Night
Auto/Color/BW/EXT (True Day/Night with ICR control module)
Multiple functions
OSD menu
IR Emitters
N/A
N/A
N/A
N/A
N/A
36 long life LEDs
IR Configuration
IR Wavelength
IR LED Minimum Lifespan
IR Range
Split glass isolation prevents internal reflections
850nm
20,000 hours of operation
Up to 60M (196ft) <AGC ON>
IR Output
Intelligent Variable Intensity Illumination/Energy
Management
N/A
3D-DNR
Off/On switchable
Digital WDR
Digital Slow Shutter
Mirror
Outdoor / Indoor
Sens-Up 256X
Off/Mirror/V-Flip/Rotate Selectable
Off/On selectable up to 32X
Off/On for 4 selectable zones
Off/On for 8 selectable zones
Control input for menu/configuration
12VDC/24VAC
Digital Zoom
Motion Detection
Privacy Mask
RS-485
Power Source
Power Consumption
12VDC: 8W max.
24VAC: 9W max.
Operating Temperature
-40°C~50°C ; -40°F~122°F (built-in heater)
Weatherproof
IP66 rated
Yes
Vandal Resistant
316.2mm (L) x 82.5mm (H) x 105.5mm Diameter (W) ;
12.49 in. (L) x 3.24 in. (H) x 4.15 in. Diameter (W)
Dimensions
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Weight
1250 g / 2.275 lbs.
Mounting Pattern
Speedy-Mount Ring mates with 4” round electrical box; base swivel is 1” NPT – remove base
plate for coupling to standard conduit fittings.
Certifications
CE / FCC
1.4 Dimensions
Front view
Camera Body
10
Download from Www.Somanuals.com. All Manuals Search And Download.
1.5 CameraComponentDescription
Speedy-mount Ring
Sunshield
Use a coin or screwdriver
to remove the cover
Controls are inside the cover
1
4
2
3
Red: Menu mode
Green: Lens mode
1) Reset:
To load the factory default configuration press the button, which is inside this
hole, for 3 seconds. Please gently insert a thin, non-metallic device into the hole
to operate the reset button.
2) Control Key: For setting Lens & OSD menu. Press the mini-joystick and hold for 5 seconds to
switch between Lens & Menu setting. When the camera is in Lens mode, turn
the mini-joystick up (ꢀ) or down (ꢁ) to zoom in/ zoom out. Turn the mini-
joystick left (ꢂ) or right (ꢃ) to adjust focus.
3) Lens/Menu: Lens LED will turn green when you select the Lens adjustment mode. Menu
LED will turn red when you select the Menu setting mode.
4) Video/GND: for aim and focus access to video at the camera, use the Video Test Cable
supplied to connect to a hand held test monitor (EN220 or similar).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
1.6 RelatedProducts
In addition, you may order the following EverFocus products which are recommended for use
with the camera to achieve the best performance:
•
EverFocus control keyboard (EKB500)
•
Any EverFocus DVR with RS-485 interface for PTZ control
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
2 INSTALLATION
This chapter will describe, in general terms, how to install the EZ610/630 camera.
STEPS:
1. Wire and mount the camera. See 2.1
2. Adjust the camera position. See 2.2
Warning
To prevent electrical shock, turn off the electrical power before making electrical connections.
2.1 WiringandMounting
Use the template and an appropriate tool to drill 4 holes to attach the speedy-mount ring. If no
surface wire will be used, please insert the provided plug into the ring from the underside; the
plug will be held securely in place by the ring. If surface wire access is required, simply omit the
plug to leave the surface wire channel clear.
Push the plastic anchors into the 4 holes.
3. Take a long Phillips pan head screw and tighten it through the EZ Mount Ring counter-bored
hole into a plastic anchor. Repeat this step until all 4 screws are secured to the wall/ceiling.
4. Drill a 1” diameter hole within the interior of the EZ Mount Ring.
5. Pull the cables to be connected to power & video cables from the ceiling or wall.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Video & Power cables
RS485 cable
(optional)
White: RS-485 +
Black: RS-485 -
Power Socket
RS-485 cable
Connect the power and video cables. Attach the camera to the speedy-mount ring, securing it
with the 4 socket head cap screws provided.
Video
Video In
Power
RS-485
Optional
12VDC
24VAC
Power and Video connection:
Note: For details of RS-485 connection please consult chapter 4, for RS-485 setup chapter 3.2!
14
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 AdjustCameraPosition
Adjust the viewing angle to the desired direction. With this unique 3-axis positioning system,
installers can capture images from virtually any angle, without compromising. The camera can
be adjusted in 3 ways.
1st axis
Use a hexagon key to loosen this screw to
rotate the camera 360°
2nd axis
Use a hexagon key to loosen this screw to
rotate the camera 180°
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3rd axis
Loosen lock ring and set screw to rotate camera 360°
Sunshield
To remove or install the sunshield, use the hexagon wrench provided to loosen the screw at
sunshield.
Loosen this screw
Slide rib on interior of sunshield into track on
outside of camera body from front to back.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: When properly installed, the rear of the sunshield is even with the rear of the camera
body; improperly extending the sunshield to ‘shade’ the lens can compromise image
quality, particularly on the EZ630 IR model.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
3 OSD MENU SETUP
This chapter introduces how to change RS485 ID and Baud Rate and to configure the camera
OSD menu.
STEPS
If you want to connect to the camera with a keyboard or other RS-485 - controller, please refer to
Section 3.2 RS485 ID & Baud Rate setting. Otherwise, please go to STEP 2.
Configure the camera, as described below:
3.1 ControlKeyGeneralOperationGuide
Switch between Lens and Menu operation
Press and hold ( ~ 5 s) the joystick button for changing the operation mode of the
joystick. Red LED: Menu mode, Green LED lens control mode.
Bring Up the General OSD Menu
Simply press the mini-joystick to bring up the general OSD menu.
Note: Make sure, that the joystick is in "MENU" mode (red LED under Joystick).
Navigate among the OSD Menu Items
Angle the mini-joystick up (ꢀ) or down (ꢁ) to move the cursor up or down.
Change Modes or Setting Parameters
Angle the mini-joystick left (ꢂ) or right (ꢃ) to adjust the mode or value of settings.
Switch to Sub-menu Screens
When an item with a sub-menu is selected, press in on the mini-joystick to switch to the
sub-menu for further settings. This may also be referred to in the instructions below as
“pressing the setup button”. Please refer to the diagram below.
SETUP
EVERFOCUS
DC
1. LENS
DC LENS
2. EXPOSURE
3. WHITE BAL.
4. DAY NIGHT
5. 3DNR
AWB
EXT
ON
ꢃBRIGHTNESS |+++++++++| 45
RETURN RET
6. SPECIAL
7. ADJUST
8. RESET
9. EXIT
18
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: For those selected items with “
” sign in the end, there is a sub-menu for further
settings.
Return to Previous Page
Go to “Return” by turning the mini-joystick and press the mini-joystick to return to
previous page.
Close the Host Menu Screen
To close the menu screen, navigate to the “EXIT” item and press the mini-joystick.
3.2 RS485ID&BaudRateSetting
Default setting for RS-485 is:
Protocol:
Baud rate:
RS-485 ID:
EverFocus or Pelco-D, self detecting (no setup required)
9600
1
The setup of RS-485 parameters should be done as first step of camera OSD setup, because a
camera reset is required for this.
Press the RESET key with a thin tool and hold for ~3 seconds.
The camera will perform a factory reset, after this the current RS-485 address is shown on the
top of the screen:
Example:
ID 01
RS485 ID is adjustable in the range 001~128. Default value is 01. Move joystick UP and Down
to adjust it. Press “Set” key to confirm the setting.
Now the current Baud Rate appears on the top of the screen:
Example:
9600
The Baud Rate is adjustable for the values 9600, 4800, 2400 and 1200. Default value is 9600.
Move joystick UP and Down to adjust it. Press “Set” key to confirm and finalize the setting.
Note: 1. For camera protocol, EZ610/630 recognizes Everfocus or Pelco-D protocols
automatically (No setting is required).
2. Camera ID and baud rate setting can only be performed locally, not from Keyboard.
3. RS-485 ID and Baud rate have to match the controller settings for this camera and the
connected RS-485 port.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 OSDMenuSetup
3.3.1 OSD Menu Tree
Default settings are shown bold or in brackets.
Lens
DC
Brightness 0~100 (50)
Exposure
Shutter
x256, x128, x64, x32,
x16, x8, x4, x2, 1/60(NTSC) / 1/50
(PAL), FLK,1/250, 1/500, 1/1000,
1/2000, 1/5000, 1/10000
HIGH ; MIDDLE ;
AGC
LOW ; OFF
SENS-UP
BLC
AUTO (x8) ; OFF
OFF
BLC
Gain
Low, Middle, High
0~8 (5)
Default, Left/Right,
Width, Top/Bottom,
Height, Return
Level
HSBLC
Default, Left/Right,
Width, Top/Bottom,
Height, Return
D-WDR
Return
Off, Indoor, Outdoor
White Balance
ATW
AWB
AWC->SET
Manual
Red
Blue
0~100 (25)
0~100 (35)
Return
Indoor
Outdoor
Return
Day/Night
EXT (*)
Auto
Delay
0~63 (5)
S-Level
D-Level
0~100 ( 56)
0~100 ( 6)
Color
Black/White
Burst
Off, On
Return
Return
3DNR
ON
Level
0~100 (30)
Return
OFF
Special
Camera Title
ON
Characters 0....Z
OFF
Return
D-Effect
Mirror
H_MIR ; V_MIR ; OFF
Gamma
Neg_Image
Return
0.45~1.00
ON ; OFF
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Motion
Off
On
Area Select
Area Display
Left/Right
Width
Area1-Area4
Off, On
5~66
0~93
Top/Bottom
Height
1~60
0~60
Sensitivity
Motion View
Return
0~40
Off, On
Privacy
Off
On
Area Select
Area Display
Left/Right
Width
Area1-Area4
Off, On
6~98
0~93
Top/Bottom
Height
0~60
0~61
Color
0~15
Return
Sync.
INT / LL
Language
English
Trad. Chinese
Simp. Chinese
Japanese
Return
Return
Adjust
Sharpness
Blue
Red
0~31 (16)
0~100 (63)
0~100 (63)
Reset
Exit
Factory
Return
* EXT: Default value for EZ630
** Color: Default value for EZ610
3.3.2 LENS
When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by
using the UP and DOWN buttons.
The iris opening can be adjusted in DC mode in LENS LEVEL. The level can be adjusted from 0
to 50.
Please select RETURN and press the SETUP button if you would like to return to the previous
menu.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.3 EXPOSURE
3.3.3.1 SHUTTER
1. When the SETUP menu is displayed on the screen, please direct the arrow to point to
“EXPOSURE” -> “SHUTTER” by using the UP and DOWN buttons.
2. Select the shutter mode by pressing the LEFT or RIGHT button.
Select from x256, x128, x64, x32, x16, x8, x4, x2, 1/60 (1/50 at PAL), FLK, 1/250, 1/500,
1/1000, 1/2000, 1/5000, 1/10000, 1/100000 for NTSC model or x256, x128, x64, x32, x16,
x8, x4, x2, 1/50, FLK, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/10000, 1/00,000 for PAL
model.
FLK: Please select “FLK” mode when flickering occurs on the screen, because of an
irregular balance between illumination and frequency. NTSC model: 1/100, PAL model:
1/120.
3. Select RETURN and press the SETUP button when you finish all the settings.
NOTE: Make sure for default setting 1/60 (NTSC) / 1/50 (PAL), if SENS-UP function is needed in
the installation. All other Shutter modes will disable SENS-UP functionality.
3.3.3.2 AGC (Auto Gain Control – basic low light signal amplification)
Please direct the arrow to point to “AGC” by using the UP and DOWN buttons.
Select the level you would like to choose by pressing the LEFT or RIGHT button. The more the
level of gain increases, the brighter the screen, but the level of noise increases as well. Please
select from HIGH, MIDDLE, LOW and OFF.
Note: AGC must be on for sense-up low light boost to function.
3.3.3.3 SENS-UP
SENS-UP is used to keep a brilliant, vivid screen image under low light level conditions by
automatically compensating for changes in the level of light.
Please direct the arrow to point to “SENSE-UP” by using the UP and DOWN buttons.
Select the mode you would like to operate by pressing the LEFT or RIGHT button.
AUTO: Low light level auto mode. Press SET for adjusting the maximum number of interpolated
images. (Default is Auto, 8X)
OFF: The function is disabled.
Press select RETURN and the SETUP button when you finish all the settings.
NOTE: 1. SENS-UP will be disabled, if AGC is OFF or the default SHUTTER value (1/50 PAL /
1/60 NTSC) was changed
2. The image becomes brighter when the setting increases; however, the after image
increases as well. Due to the increased light sensitivity of the Super HAD II chip, far less
DSP ‘boost’ is needed, resulting in color or B/W images in low light with minimal ghosting.
3. Please note that spots and noise may appear if light amplification increases when
SENSE-UP is operating. This is a normal phenomenon, controllable with DNR.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.3.4 BLC-Backlight Compensation
There are three choices for the type of BLC which may be employed: OFF, traditional BLC or HSBLC.
BLC
Video gain can be adjusted automatically to correct the exposure of subjects that are in front of a
bright light source.
Please direct the arrow to point to “BLC” by using the UP and DOWN buttons.
Select the BLC mode by pressing the LEFT or RIGHT button. Then make adjustments as below:
GAIN
Select from High, Middle and Low.
DEFAULT
LEFT/RIGHT
Set the factory default values for BLC.
Set the Left/Right side of an area for the BLC to be adjusted. The value
adjustable is 0~6.
WIDTH
Set the width of an area for the BLC to be adjusted. The value adjustable is
0~6.
TOP/BOTTOM
HEIGHT
Set the Top/Bottom side of an area for the BLC to be adjusted. The value
adjustable is 0~6.
Set the height of an area for the BLC to be adjusted. The value adjustable is
0~6.
RETURN
Press “RET” to save all settings in the BLC menu and return to the previous
menu.
Press “END” to save all the menu settings and exit.
HSBLC
HSBLC (Highlight Suppression BLC) is used to reduce the brightness of light sources in a
specific area. It is activated only in a low illumination environment to minimize the effects of glare
from bright lights such as spotlights, street lights or headlights in the field of view. Where
‘traditional’ BLC can increase the exposure of a dark area surrounded by a brighter area, HSBLC
can decrease the exposure of bright areas surrounded by darker areas.
1. Please direct the arrow to point to “BLC” by using the UP and DOWN buttons.
2. Select the HSBLC mode by pressing the LEFT or RIGHT button. Then make adjustments as
below:
LEVEL
Adjust the sensitivity level for HSBLC from 0 to 8.
Set the factory default values for HSBLC.
DEFAULT
LEFT/RIGHT
Set the Left/Right side of an area for the HSBLC to be adjusted. The value
adjustable is 0~6.
WIDTH
Set the width of an area for the HSBLC to be adjusted. The value adjustable is
0~6.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TOP/BOTTOM Set the Top/Bottom side of an area for the HSBLC to be adjusted. The value
adjustable is 0~6.
HEIGHT
Set the height of an area for the HSBLC to be adjusted. The value adjustable
is 0~6.
RETURN
Press “RET” to save all settings in the HSBLC menu and return to the previous
menu.
Press “END” to save all the menu settings and exit.
3.3.3.5 D-WDR
When there are both bright and dark areas in the field of view at same time, this function can
help to even the exposure between these areas.
1.
2.
Please direct the arrow to point to “D-WDR” by using the UP and DOWN buttons.
Select the mode you would like to operate by moving the joystick LEFT or RIGHT.
OFF
Disables D-WDR function (default)
INDOOR
OUTDOOR
Return
Select this option if you are in an indoor environment.
Select this option if you are in an outdoor environment.
Press “RET” to save all settings in the Exposure menu and return to the
previous menu.
Press “END” to save all the menu settings and exit.
3.3.4 WHITE BALANCE CONTROL
The screen color can be adjusted by using the WHITE BALANCE function.
Please direct the arrow to point to “WHITE BAL” by using the UP and DOWN buttons.
Please select the mode you would like to operate by pressing the LEFT or RIGHT button.
Please select one of the 6 modes below:
ATW
AWB
Auto Tracking White Balance: This mode can be used within the color
temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor,
sodium vapor lamp or inside tunnels).
Auto White Balance: This mode can be used within the color temperature range
from 2,500°K to 10,000°K. (default)
AWC ->SET To find the optimal setting for the current luminance environment in this mode,
point the camera toward a sheet of white paper, and press “SET”. If the
environment changes, you will have to readjust it.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL
The manual adjustment mode enables a more precise adjustment. Please select
ATW or AWC first. Then change to manual adjustment mode and press the
SETUP button. Set the suitable color temperature, and increase or decrease the
red and blue color values at the same time while checking the color changes of
the objects in view.
Press “RET” to save all settings in this menu and return to the previous menu.
Press “END” to save all the menu settings and exit.
INDOOR
Select this option when the color temperature is 5,600°K.
Select this option when the color temperature is 3,300°K
OUTDOOR
Press “RET” to saves all settings in this menu and returns to the previous menu.
Press “END” to save all the menu settings and exit.
3.3.5 DAY NIGHT
These settings control the operation of the camera when the illumination level changes. Choices
are Color at all times; B/W at all times; or color when illumination is bright, switching to B/W in
low light. PLEASE NOTE: In “color” operation, there is an IR “cut” (blocking) filter between the
lens and the sensor; the EZ630 has very little IR sensitivity when the image is displayed in
color. The EZ630 camera will have excellent IR sensitivity when displaying a low light B/W
picture. To properly utilize the IR illuminators on the EZ630 in low light situations, it is
essential to select either the AUTO or the B/W operating mode in this menu.
B/W
The picture is always displayed in B/W.
BURST
OFF/ON:
ON: Retains the color burst information; minor color noise may appear
when ambient illumination is low.
OFF: With color burst signal off, picture will be pure B/W.
Press “RET” to save all settings in the DAY/NIGHT menu and returns to the
previous menu.
Press “END” to save all the setting menus and exit.
COLOR
AUTO
The picture is always displayed in color, even at low light levels.
NOTE: In “color” operation, there is an IR “cut” (blocking) filter between the
lens and the sensor; thus EZ610/630 camera has very little IR sensitivity
when the image is displayed in color. (default for EZ610)
The picture switches to color in a normal (bright) environment and switches
to B/W when the ambient illumination is low. The switching point is controlled
by the video signal level.
Note: AGC selection must be set as middle or high in order to employ the
auto switching function.
Delay
Delay time for switch reaction on light changes, range 0~63 seconds.
S-Level Trigger level for switching to day mode in range 0~100.
E-Level Trigger level for switching to night mode in range 0~100.
NOTE: The AUTO mode is not recommended for applications with high-
power IR illumination. The camera may switch continuously between
Day and Night mode.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EXT
The picture will switch automatically to color in a normal environment and to
B/W when the ambient illumination is low based on the illumination reaching
the light sensor at the front of the camera body. (default for EZ630)
3.3.6 3DNR
3DNR reduces the background noise in a low luminance environment.
OFF
ON
Disables 3DNR to keep the same amount of noise.
Enables 3DNR to reduce the noise. (default)
Level
Noise reduction level from 0~100 while observing a low light image until the
desired image is achieved. (default=30)
Press “RET” to saves all settings in DNR menu and returns to the previous menu.
Press “END” to save all the setting menus and exit.
3.3.7 SPECIAL
In this section, user can do special settings including camera title, digital effects, motion, privacy
zones, synchronization and language.
Please direct the arrow to point to “SPECIAL” on the SETUP menu by using the UP and DOWN
buttons.
Select the mode you would like to operate by pressing the LEFT or RIGHT button.
3.3.7.1 CAM TITLE
Input the camera title, and it will be appeared on the monitor.
Please direct the arrow to point to “CAM TITLE” by using the UP or DOWN button.
Select “ON” by pressing the LEFT or RIGHT button.
Press SETUP button.
Maximum 15 characters can be used for the ID.
Use UP, DOWN, LEFT and RIGHT buttons to move the cursor to the letter to be chosen.
Use SETUP button to choose that letter.
Once a name has been selected, please choose the position on the screen where you would like
to display the name.
Move the cursor onto “POS” and press the SETUP button.
The name will appear at the top left hand corner.
Please use the 4 directional buttons to move the position of the displayed name.
Press the SETUP button when the desired location has been reached.
If you would like to cancel the ID entered, please move the cursor to “CLR”, and all the letters
entered will be deleted.
Select “END” and press the SETUP button to complete ID input.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.7.2 D-EFFECT
Offers a number of digital functions for processing the image.
3.3.7.3 FREEZE
OFF
ON
Select “OFF” to view live image.
Select “ON” to freeze and display current live image.
3.3.7.4 MIRROR
OFF
Disable digital effects.
MIRROR
V-FLIP
ROTATE
The image is displayed horizontal flipped.
The image is displayed vertical flipped.
Rotate the image 180˚.
3.3.7.5 D-ZOOM
Setup for digital zoom.
OFF
ON
Disable the D-ZOOM function
D-Zoom: Select digital zoom from X1.0 up to X32. Note that zoom levels
above X4 may lead to excessive pixellation.
Setup of the position of the magnified image in view (0 is the center of the
image):
Pan: Select digital pan from -100 to 100.
Tilt: Select digital tilt from -100 to 100.
Press “RET” to saves all settings in D-ZOOM menu and returns to the previous menu.
Press “END” to save all the setting menus and exit.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.7.6 GAMMA
This menu allows adjustment of gamma correction for ideal linearity of image brightness and
contrast in the range 0.05 to 1.0.
3.3.7.7 NEG. IMAGE
Allows user to create a negative of the original image. A negative image is a tonal inversion of a
positive image, in which light areas appear dark and vice versa. A negative color image is
additionally color reversed, with red areas appearing cyan, greens appearing magenta and blues
appearing yellow.
3.3.7.8 RETURN
Return: Press “RET” to save all settings in D-EFFECT menu and return to the previous menu.
Press “END” to save all the menu settings and exit.
3.3.7.9 MOTION
This camera enables you to observe movements of objects in 4 different areas on the screen,
and the message “MOTION DETECTED” appears on the screen when movement is detected.
The camera detects an object’s movement by sensing changes in the pixels displayed.
OFF
Disables the MOTION function.
ON
AREA SELECT
Please select the area you would like to detect from the 4 areas in AREA
SELECT mode
AREA DISPLAY Select “ON” to use the motion area selected in sensitivity. Select “OFF” to
disable this function.
LEFT/RIGHT
WIDTH
Set the coordinate of the horizontal axis 5~66.
Set the size of horizontal area 0~93.
TOP/BOTTOM
HEIGHT
Set the coordinate of the vertical axis 1~60.
Set the size of vertical area 0~60.
SENSITIVITY
Set the sensitivity level for the motion trigger by selecting from 0~40. When
the sensitivity value is high, motion detection sensitivity increases to sense
very small movements and vice versa.
MOTION VIEW
RETURN
Select “ON” to display motion detection pixels in the live view.
Press “RET” to save all settings in MOTION menu and return to the
previous menu. Press “END” to save all the menu settings and exit.
3.3.7.10 PRIVACY
This mode masks areas you do not want to display on the screen or record.
OFF
Disable the PRIVACY function.
ON
AREA SELECT
Please select the area you would like to hide from the 8 areas in AREA
28
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECT mode.
AREA DISPLAY Select “ON” to use the area selected in the AREA SELECT. Select “OFF”
to disable this function.
LEFT/RIGHT
WIDTH
Set the coordinate of the horizontal axis 6~98.
Set the size of horizontal area 0~93.
TOP/BOTTOM
HEIGHT
Set the coordinate of the vertical axis 0~60.
Set the size of vertical area 0~61.
COLOR
Set area color. It is selectable from 0 to 15.
RETURN
Press “RET” to save all settings in PRIVACY menu and return to the
previous menu. Press “END” to save all the menu settings and exit.
3.3.7.11 SYNC
There are two SYNCHRONIZATION modes INTERNAL and LINE-LOCK. In LINE-LOCK mode,
the video signal is synchronized to the frequency of the incoming AC power. The Line-Lock
synchronization can only be used when the supply power is 24VAC 60Hz (NTSC models) or
50Hz (PAL models).
INT
L/L
Internal synchronization
Line-lock synchronization (only for 24 VAC)
3.3.7.12 LANGUAGE
Select OSD language. EZ610/630 camera supports multiple languages including English,
Japanese, Traditional Chinese and Simplified Chinese.
3.3.7.13 RETURN
Press “RET” to save all settings in the SPECIAL menu and return to the previous menu.
Press “END” to save all the menu settings and exit.
3.3.8 ADJUST
Adjust sharpness, Blue and Red level in this section.
3.3.8.1 SHARPNESS
The contour of the video image becomes cleaner and more easily distinguished as the level of
SHARPNESS increases. If the level is set too high, it may affect the video image and cause
noise. The available range of level is 0~31.
3.3.8.2 BLUE
Adjust image’s blue level. The available range of level is 0~100.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.8.3 RED
Adjust image’s red level. The available range of level is 0~100.
Press “RET” to saves all settings in the ADJUST menu and returns to the previous menu.
Press “END” to save all the menu settings and exit.
3.3.9 RESET
3.3.9.1 FACTORY RESET
Reset to the factory default settings.
Press “RET” to return to the previous menu.
Press “END” to exit.
3.3.9.2 EXIT
Save all the menu settings and exit.
NOTE: If you quit a Menu without pressing EXIT, all the settings you previously modified will
NOT be saved.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter
4 RS-485 REMOTE CONTROL
4.1 RemotecontrolwithEKB-500keyboard
4.1.1 RS - 485 Wiring
For more details about RS-485 wiring please consult related chapters in EKB-500 user manual.
Note!
Before being able to control keyboard, make sure Keyboard RS485 camera ID, Baud rate match
the camera. (see COM port and CAMERA setting in EKB500 manual).
EZ610/630 camera ID default is 01. Baud rate is 9600. Supported Protocols are EverFocus and
Pelco-D. The camera detects the protocol of incoming commands automatically.
4.1.2 OSD Menu Setting by Keyboard
a. On the EKB500, choose the Camera (Camera ID) to be controlled. Then press “Menu” to
enter the SETUP menu.
b. Move the joystick UP (ꢀ) and DOWN (ꢁ). This allows you to move between selection
items in the setup menu.
c. If the item has sub-menu setting (sign
), press “Menu” again to display the sub-menu.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP
1. LENS
2. EXPOSURE
3. WHITE BAL.
DC
AWB
d. Move the joystick RIGHT (ꢃ) and LEFT (ꢂ) to adjust the mode and parameters of the
selected item.
Press “Menu” to leave and goes to previous menu after setting. Move to “exit” and press “menu”
button when you finish all settings.
For detail setting of each setup function, Please refer to “3.3. OSD Menu Setup”.
4.1.3 Lens Adjustment by Keyboard
1. Press Zoom in or Zoom out to adjust zoom; or turn the Joystick clockwise to zoom out, and
counterclockwise to zoom in.
2. Press Focus N or Focus F to adjust focus.
4.2 RemoteControlwithEverFocusDVR
4.2.1 RS-485 Wiring
The connection to the DVR depends on DVR type. The EverFocus EDSR and EDR series (MPEG4)
provide 2 looped RJ45 sockets with same pinout as EKB-500 keyboard (chapter 4.1.1). The DVR of
Paragon and ECOR series as well as EverFocus video server have 2-pin screw terminal connectors
for RS-485 interface.
4.2.2 Camera Operation and Setup by DVR
The DVR have different layout and functionality for PTZ control.
If the DVR does not provide buttons for PTZ OSD menu, following alternative commands can be used
for EZ610/630 OSD menu:
Set Preset 95
Iris open (Iris +)
Iris close (Iris -)
Open OSD menu
Enter / Set
ESC / Close OSD menu
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EverFocus Electronics Corp.
Headquarters Office
Beijing office
12F, No.79 Sec.1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
Tel: +886-2-26982334
Room 609,Technology Trade Building.
Shangdi Information Industry Base,
Haidian District,Beijing China
Tel: +86-10-62971096
Fax: +886-2-26982380
Fax: +86-10-62971423
European Office
Japan Office
Albert-Einstein-Strasse 1,
D-46446 Emmerich, Germany
Tel: +49-2822-9394-0
5F Kinshicho City Building，2-13-4 Koto-bashi，
Sumida-Ku，Tokyo，130-0022，Japan
Tel: +81-3-5625-8188
Fax: +49-2822-939495
Fax: +81-3-5625-8189
USA California Office
USA New York Office
1801 Highland Ave. Unit A
Duarte, CA 91010 ,U.S.A
Tel: +1-626-844-8888
415 Oser Ave Unit S
Hauppauge, NY 11788
Sales: +1-631-436-5070
Fax: +1-631-436-5027
Fax: +1-626-844-8838
India Office
UK Office
Unit 12 Spitfire Business Park Hawker Road
Croydon, CR0 4WD
London: 0845 430 9999
Suite 803, 8th Floor,
Housefin Bhavan,
C-21 Bandra Kurla Complex,
Bandra (East), Mumbai 400 051
Tel: +91 22 6128-8700
Telford: 0845 430 8888
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their end-of-
life, should be disposed of separately
from your household waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
33
Download from Www.Somanuals.com. All Manuals Search And Download.
|