User’s Manual
Color LCD Monitor
It shall be assured that the final system is in compliance to
IEC60601-1-1 requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
English
TABLE OF CONTENTS
PRECAUTIONS...................................................................................4
1. INTRODUCTION .....................................................................................9
1-1. Features ........................................................................................................9
1-2. Package Contents..........................................................................................9
1-3. Controls & Connectors ..............................................................................10
2. CABLE CONNECTION .........................................................................12
2-1. Before Connecting ......................................................................................12
2-2. Connecting the signal cable (For the computer employing D-Sub or DVI
connector) ..................................................................................................13
2-3. Connecting the signal cable (For the computer employing ADC)..............16
2-4. Connecting Two PCs to the Monitor..........................................................19
3. ScreenManager....................................................................................21
3-1. How to use the ScreenManager ..................................................................21
3-2. ScreenManager Adjustments and Settings...................................................22
3-3. FineContrast...............................................................................................23
3-4. Useful Functions .........................................................................................24
4. ADJUSTMENT ......................................................................................26
4-1. Screen Adjustment ......................................................................................26
4-2. Displaying Low Resolutions .......................................................................30
4-3. Color Adjustment .......................................................................................32
4-4. Power-save Setup........................................................................................35
5. MAKING USE OF USB (Universal Serial Bus)...................................36
6. ATTACHING AN ARM...........................................................................38
7.TROUBLESHOOTING...........................................................................40
8. CLEANING............................................................................................44
9. SPECIFICATIONS.................................................................................45
10. GLOSSARY.........................................................................................48
APPENDIX/ANHANG/ANNEXE ..................................................................i
TABLE OF CONTENTS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
English
PRECAUTIONS
IMPORTANT!
• This product has been adjusted specifically for use in the region to which it was
originally shipped. If operated outside the region to which it was originally shipped,
the product may not perform as stated in the specifications.
• To ensure personal safety and proper maintenance, please read this section and the
caution statements on the unit (refer to the figure below).
[Location of the Caution Statements]
[Symbols on the unit]
Symbol
Location
This symbol indicates
Top
Main power switch
Press to turn the monitor’s main power off.
Top
Main power switch
Press to turn the monitor’s main power on.
Power button
Front
Control panel
Press to turn the monitor’s power on or off.
Rear
Alternating current
Name Plate
Rear
Alerting electrical hazard
Rear
Caution
Refer to SAFETY SYMBOLS section in this
manual.
4
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
If the unit begins to emit smoke, smells like something is burning, or
makes strange noises, disconnect all power connections immediately
and contact your dealer for advice.
Attempting to use a malfunctioning unit may result in fire, electric shock, or
equipment damage.
Do not open the cabinet or modify the unit.
Opening the cabinet or modifying the unit may result in fire, electric shock, or
burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing covers
may result in fire, electric shock, or equipment damage.
Keep small objects or liquids away from the unit.
Small objects accidentally falling through the ventilation slots into the cabinet
or spillage into the cabinet may result in fire, electric shock, or equipment
damage.
If an object or liquid falls/spills into the cabinet, unplug the unit immediately.
Have the unit checked by a qualified service engineer before using it again.
Place the unit at the strong and stable place.
A unit placed on an inadequate surface may fall and result in injury or
equipment damage.
If the unit falls, disconnect the power immediately and ask your dealer for
advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock.
Set the unit in an appropriate location.
Not doing so may result in fire, electric shock, or equipment damage.
* Do not place outdoors.
* Do not place in the transportation system (ship, aircraft, trains, automobiles,
etc.)
* Do not place in a dusty or humid environment.
* Do not place in a location where the steam comes directly on the screen.
* Do not place near heat generating devices or a humidifier.
* Do not place in an inflammable gas environment.
To avoid danger of suffocation, keep the plastic packing bags away
from babies and children.
PRECAUTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
Use the enclosed power cord and connect to the standard power outlet
of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
To disconnect the power cord, grasp the plug firmly and pull.
Tugging on the cord may damage and result in fire or electric shock.
The equipment must be connected to a grounded main outlet.
Not doing so may result in fire or electric shock.
Use the correct voltage.
* The unit is designed for use with a specific voltage only. Connection to
another voltage than specified in this User’s Manual may cause fire, electric
shock, or equipment damage.
* Do not overload your power circuit, as this may result in fire or electric
shock.
Handle the power cord with care.
* Do not place the cord underneath the unit or other heavy objects.
* Do not pull on or tie the cord.
If the power cord becomes damaged, stop using it. Use of a damaged cord
may result in fire or electric shock.
Never touch the plug and power cord if it begins to thunder.
Touching them may result in electric shock.
When attaching an arm stand, please refer to the user’s manual of the
arm stand and install the unit securely with the enclosed screws.
Not doing so may cause the unit to come unattached, which may result in
injury or equipment damage. When the unit is dropped, please ask your dealer
for advice. Do not continue using a damaged unit. Using a damaged unit may
result in fire or electric shock. When reattaching the tilt stand, please use the
same screws and tighten them securely.
6
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
Do not touch a damaged LCD panel directly with bare hands.
The liquid crystal which leaks from the panel is poisonous if it enters the eyes
or mouth.
If any part of the skin or body comes in direct contact with the panel, please
wash thoroughly. If some physical symptoms result, please consult your
doctor.
Follow local regulation or laws for safe disposal.
The backlight of the LCD panel contains mercury.
CAUTION
Handle with care when carrying the unit.
Disconnect the power cord and cables when moving the unit. Moving the unit
with the cord attached is dangerous. It may result in injury.
When handling the unit, grip the bottom of the unit firmly with both
hands ensuring the panel faces outward before lifting.
Dropping the unit may result in injury or equipment damage.
Do not block the ventilation slots on the cabinet.
* Do not place any objects on the ventilation slots.
* Do not install the unit in a closed space.
* Do not use the unit laid down or upside down.
Blocking the ventilation slots prevents proper airflow and may result in fire,
electric shock, or equipment damage.
Do not touch the plug with wet hands.
Doing so may result in electrical shock.
Use an easily accessible power outlet.
This will ensure that you can disconnect the power quickly in case of a
problem.
Periodically clean the area around the plug.
Dust, water, or oil on the plug may result in fire.
Unplug the unit before cleaning it.
Cleaning the unit while it is plugged into a power outlet may result in electric
shock.
If you plan to leave the unit unused for an extended period, disconnect
the power cord from the wall socket after turning off the power switch
for the safety and the power conservation.
PRECAUTIONS
7
Download from Www.Somanuals.com. All Manuals Search And Download.
English
LCD Panel
In order to suppress the luminosity change by long-term use and to maintain
the stable luminosity, please use the monitor with the brightness below 160
cd/m2 (BRIGHTNESS approximately 70 %).
The screen may have defective pixels. These pixels may appear as slightly light
or dark area on the screen. This is due to the characteristics of the panel itself,
and not the product.
The backlight of the LCD panel has a fixed life span. When the screen becomes
dark or begins to flicker, please contact your dealer.
Do not press on the panel or edge of the frame strongly, as this may result in
damage to the screen. There will be prints left on the screen if the pressed
image is dark or black. If pressure is repeatedly applied to the screen, it may
deteriorate or damage your LCD panel. Leave the screen white to decrease the
prints.
Do not scratch or press on the panel with any sharp objects, such as a pencil or
pen as this may result in damage to the panel. Do not attempt to brush with
tissues as this may scratch the LCD panel.
8
PRECAUTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
1. INTRODUCTION
Thank you very much for choosing an EIZO Color Monitor.
1-1. Features
• Dual inputs compliant (DVI-I connecter x 2)
• DVI (p. 48) Digital input (TMDS (p. 49)) compliant
• [Horizontal scanning frequency]
Analog: 30 - 82 kHz
Digital: 30 - 65 kHz
[Vertical scanning frequency]
Analog: 49 - 86 Hz (1280 x 1024: 49 - 75 Hz)
Digital: 59 - 61 Hz (VGA text: 69 - 71 Hz)
[Resolution]
[Frame synchronous mode]
1M pixels (1280 dots × 1024 lines)
57.5 - 67 Hz supported
• Smoothing function incorporated for the adjustment of an enlarged image (p.30)
• FineContrast modes, to select the most suitable mode for screen display (p.23)
• Selectable DICOM (p.48) Part 14 complied screen (FineContrast modes, p.23)
• The utility software “ToneCurve Tuning Utility” (for Windows), which can adjust the
tone setting of the monitor from the computer, is included (refer to the ToneCurve
Tuning Utility Disk).
• The utility software “ScreenManager Pro for LCD” (for Windows) which can control
the monitor from a PC with a mouse or keyboard, is included (refer to the EIZO LCD
Utility Disk).
• The height adjustable stand incorporated
• Ultra slim bezel incorporated
• The Portrait display capability
1-2. Package Contents
Please contact your local dealer for assistance if any of the listed items are missing or
damaged.
• LCD Monitor
• Power Cord
• ToneCurve Tuning Utility Disk
• EIZO LCD Utility Disk
• Signal Cable (FD-C16)
• Signal Cable (FD-C35/FD-C39)
• EIZO USB Cable (MD-C93)
• User’s Manual
• ScreenManager Quick Reference
• LIMITED WARRANTY
NOTE
• Please retain the packing materials for future transference.
1. INTRODUCTION
9
Download from Www.Somanuals.com. All Manuals Search And Download.
English
1-3. Controls & Connectors
Front
(2)
(1)
FineContrast Menu
Control Panel
(3) (4) (5) (6)
(7)
(8) (9)
(1) ScreenManager® Main Menu
(2)
Main Power Switch
(3) SIGNAL1-2 Input Signal Selection Button
(4) MODE
(5) AUTO
(6) ENTER
(7)
Mode Button*1
Auto Adjustment Button
Enter Button
Control Buttons(Left, Down, Up, Right)*2
(8)
(9)
Power Button
Power Indicator*3
Blue
Operation
Yellow /
Power saving
Flashing yellow
(2 times for each)
Flashing yellow slowly
Off
Power is off (Main power is on)
Power off
*1 Pushing the Mode button once allows you to display a FineContrast menu. Pushing
the Mode button more than once allows you to select a FineContrast mode. (The
ScreenManager Main Menu and the FineContrast Menu cannot be displayed at the
same time.)(see page 23. )
*2 These buttons are changed to Up, Left, Right, Down in case of selecting “Portrait” for
<Orientation> of ScreenManager <Others> (p.22).
*3 Blue lighting, when the screen is displayed (Operation mode), is made to non-light,
see page 22. Regarding the power indicator for the “Off Timer”, see page 24.
10 1. INTRODUCTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Rear
(11)
(10)
Bottom
(13)
(14)
(12)
(15)
(10) Height Adjustable Stand (Detachable)* 4
(11)
Security Lock Slot*5
(12)
(13)
(14)
DVI-I Input Connector x 2 (SIGNAL 1, SIGNAL 2)
USB Upstream Port (x 1)
USB Downstream Ports (x 2)
(15)
Power Connector
*4
The LCD monitor has the capability of the Portrait/Landscape display. (The panel
pivots in the clockwise direction 90°.) For the Portrait display, use the software for
the portrait.
The LCD monitor can be used with an optional arm stand by removing the stand.
(see page 38)
*5
Allows for connection of a security cable. This lock supports Kensington’s
MicroSaver security system. For further information, please consult
Kensington Technology Group
2855 Campus Drive, San Mateo, CA 94403 USA
Tel.: 800-650-4242, x3348, Intl: 650-572-2700, x3348
Fax: 650-572-9675
1. INTRODUCTION 11
Download from Www.Somanuals.com. All Manuals Search And Download.
English
2. CABLE CONNECTION
2-1. Before Connecting
Before connecting your monitor to the PC, change the display screen settings (resolution
p. 49) and frequency) in accordance with the charts below.
NOTE
• When your computer and display support VESA DDC, the suitable resolution and
the refresh rate are set by just plugging your display into the computer without any
manual settings.
Analog Input
Resolution
Frequency
~ 85 Hz
67 Hz
Dot Clock
Remarks
VGA, VESA
Apple Macintosh
VGA TEXT
VESA
×
×
×
×
×
×
×
×
×
×
×
×
×
×
640
640
480
480
400
480
600
624
768
864
870
900
960
960
1024
1024
135 MHz
(Max.)
720
70 Hz
720
60 Hz
800
~ 85 Hz
75 Hz
VESA
832
Apple Macintosh
VESA
1024
1152
1152
1152
1280
1280
1280
1280
~ 85 Hz
75 Hz
VESA
75 Hz
Apple Macintosh
SUN WS
~ 76 Hz
60 Hz
VESA
75 Hz
Apple Macintosh
SUN WS
67 Hz
~ 75 Hz
VESA
Digital Input
Only the following resolutions with frequency can be displayed on this model.
Resolution
Frequency
60Hz
Dot Clock
Remarks
VGA
×
×
×
×
×
640
720
480
400
108 MHz
(Max.)
70Hz
VGA TEXT
VESA
800
600
60Hz
1024
1280
768
60Hz
VESA
1024
60Hz
VESA
12 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
2-2. Connecting the signal cable (For the
computer employing D-Sub or DVI
connector)
NOTE
• Be sure that the power switches of both the PC and the monitor are OFF.
1. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Power Cord
Analog Input
Signal Cable
Connector
Video Output
Connector / D-Sub mini
15 pin
PC
Signal Cable (FD-C16
enclosed)
• Standard graphics card
• Power Macintosh G3 (Blue &
White) / Power Mac G4
(VGA)
Input Connector
(monitor) / DVI
Signal Cable (FD-C16
enclosed) + Adapter*
Video Output
Connector / D-Sub 15
pin
• Macintosh
*Macintosh Adapter (Optional)
Input Connector
(monitor) / DVI
2. CABLE CONNECTION 13
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Digital Input
Signal Cable
Connector
Video Output
Connector / DVI
PC
Signal Cable
(FD-C35/FD-C39 enclosed)
• Digital graphics board
• Power Mac G4 / G5 (DVI)
Input Connector
(monitor) / DVI
2. Plug the power cord into the power connector on the rear of the
monitor.
3. Lead the power cord and signal cable into the cable holder at rear of
the monitor.
NOTE
• The cables are recommended to lead with slight sag for the smooth motion of
the stand and the Portrait/Landscape display.
Cable Holder
4. Plug the other end of the power cord into a power outlet.
The monitor's power indicator will flash yellow slowly.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
14 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
WARNING
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock. Not doing so
may result in fire or electric shock.
5. Turn on the monitor’s Power Button and then switch on the PC’s
power.
The monitor’s power indicator will light up (blue).
If an image does not appear, refer to the “7. TROUBLESHOOTING” (p.40) for
advice.
Whenever finished, turn off the PC and the monitor.
NOTE
• When turning on the monitor, the kind of the input signal (Signal1 or 2/Analog or
Digital) is displayed for a few seconds on the right top corner of the screen.
• Adjust brightness of the screen depending on the brightness of your environment.
• Be sure to take adequate rests. A 10-minute rest period each hour is suggested.
6. When using the software, ScreenManager Pro for LCD (for
Windows), connects the upstream port of the monitor to the
downstream port of the USB compliant PC or another hub with the
USB cable.
After connecting the USB cable, the USB function can be set up automatically. For
further details about the “ScreenManager Pro for LCD”, refer to the readme.txt in
the “EIZO LCD Utility Disk” CD-ROM.
2. CABLE CONNECTION 15
Download from Www.Somanuals.com. All Manuals Search And Download.
English
2-3. Connecting the signal cable (For the
computer employing ADC)
NOTE
• Be sure that the power switches of both the PC and the monitor are OFF.
1. Plug the signal cable into the connector at the rear of the monitor
and the other end of the cable into the video connector on the PC.
After connecting, secure the connection with the screw-in fasteners.
Power Cord
To Input the Signal Through ADC
Signal Cable
Connector
PC
Signal Cable (FD-C35/FD-C39,
enclosed) + ADC-DVI Display
Adapter (Commercially available)
Video Output Connector/
ADC
• Power Mac G4 / G5
(ADC)
Input Connector
(monitor)/ DVI
NOTE
• ADC-DVI display adapter is required if the monitor connects to Power Mac G4/
G5. The adapter is commercially available.
2. Plug the power cord into the power connector on the rear of the
monitor.
16 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. Lead the power cord and signal cable into the cable holder at rear of
the monitor.
NOTE
• The cables are recommended to lead with slight sag for the smooth motion of
the stand and the Portrait/Landscape display.
Cable Holder
4. Plug the other end of the cord into a power outlet.
The monitor’s power indicator will flash yellow slowly.
WARNING
Use the enclosed power cord and connect to the standard
power outlet of your country.
Be sure to remain within the rated voltage of the power cord.
Not doing so may result in fire or electric shock.
The equipment must be connected to a grounded main
outlet.
Not doing so may result in fire or electric shock. Not doing so
may result in fire or electric shock.
2. CABLE CONNECTION 17
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5. Press the power button while pressing the Input Signal Selection
button.
The Input Selection menu is appeared on the screen.
6. Change SIGNAL 1 (DVI-I Connector) in the Input Selection menu to
“ADC”.
Press Enter button to complete the setting and the menu closes.
7. Switch on the PC's power.
The monitor’s power indicator will light up (blue).
If an image does not appear, refer to the “7. TROUBLESHOOTING” (p.40) for
additional advice.
Whenever finishing your operation, turn off the PC and the monitor.
NOTE
• When changing the signal connector except ADC, open the Input Selection menu
again and change the setting to “Standard”.
18 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
2-4. Connecting Two PCs to the Monitor
Two PCs can be connected to the monitor through the Signal 1 and the Signal 2 on the
back of the monitor.
Connecting Examples
(SIGNAL 1) (SIGNAL 2)
PC 1
PC 2
(Ex.1) Analog D-Sub
Signal Cable
Signal Cable
DVI
Digital
mini 15
pin
(FD-C16 enclosed)
(FD-C35/FD-C39
enclosed)
(Ex.2) Analog D-Sub
Signal Cable
Signal Cable
D-Sub Analog
mini
15 pin
mini 15
pin
(FD-C16 enclosed)
(FD-C16 optional)
(Ex.3) Digital DVI
Signal Cable
Signal Cable
DVI
Digital
(FD-C35/FD-C39
enclosed)
(FD-C35/FD-C39
optional)
Selecting the Active Input
The Input Signal Selection Button on the control panel can be used to select either Signal
1 or Signal 2 as the active input at any time. Every time the button is pressed, the input
changes. When switching the signal, the kind of the input signal (Signal1 or 2/Analog or
Digital) is displayed for a few seconds on the right top corner of the screen.
Input Signal Selection Button
2. CABLE CONNECTION 19
Download from Www.Somanuals.com. All Manuals Search And Download.
English
The Priority Input Signal
This function is used to select which PC will have priority to control the monitor when
utilizing two PCs. The monitor constantly checks the input signals and switches
automatically in accordance with the “Input Priority” setting (see table below). Once a
priority is set, whenever a change of signal is detected at the selected input, the monitor
will switch the input to that signal.
In the case of only one signal being present at either input, the monitor automatically
detects and displays that signal.
Priority Setting
Performance
If signals from both inputs are present, the monitor gives preference
to Signal 1 in the following cases.
1
• When the power of the monitor is turned ON
(SIGNAL 1)
• When the signal input to Signal 1 is changed even if active input
was Signal 2.
If signals from both inputs are present, the monitor gives preference
to Signal 2 in the following cases.
2
• When the power of the monitor is turned ON
(SIGNAL 2)
• When the signal input to Signal 2 is changed even if active input
was Signal 1.
The monitor will not detect signals automatically in this mode. Select
the active input by pressing the Input Signal Selection Button on the
monitor’s control panel.
Manual
NOTE
• When the “1” or “2” is selected, the power saving mode of the monitor activates only
if both PCs are in power saving mode.
20 2. CABLE CONNECTION
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. ScreenManager
3-1. How to use the ScreenManager
ScreenManager allows you to adjust screen performance though the main menu and
select a FineContrast mode easily.
[Ex.] Custom
Main Menu
Control Buttons
Left, Down, Up, Right
Mode Button
Auto Adjustment
Button
FineContrast Menu
Enter Button
NOTE
• Main Menu and FineContrast Menu cannot be activated at the same time.
1. Entering the ScreenManager
Press the Enter Button once to display the main menu of the ScreenManager.
2. Making Adjustments and Settings
(1) Select the desired sub menu icon using the Control Buttons and press the Enter
Button. The sub menu appears.
(2) Use the Control Buttons to select the desired setting icon and press the Enter
Button. The setting menu appears.
(3) Use the Control Buttons to make all required adjustments and press the Enter
Button to save the settings.
3. Exiting the ScreenManager
(1) To return to the main menu, select the <Return> icon or press the Down Button
twice, followed by the Enter Button.
(2) To exit the ScreenManager, select the <Exit> icon or press the Down Button
twice, followed by the Enter Button.
NOTE
• Double clicking the Enter Button also exits the ScreenManager menu.
FineContrast Menu
Pressing the Mode button allows you to select the best suited mode for screen
display from 6 FineContrast modes; Custom, sRGB, CAL,Text, DICOM-CL and
DICOM-BL. To exit the menu, press the Enter Button. (p. 23)
3. ScreenManager 21
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-2. ScreenManager Adjustments and Settings.
The following table shows all the ScreenManager’s adjustment and setting menus.
“*” indicates adjustments of analog input only and “**” indicates digital input only.
Main menu
Sub menu
Reference
*
*
*
*
*
Screen
Clock
4-1. Screen Adjustment (p.26)
Phase
Position
Resolution
Range Adjustment
Smoothing
*
Signal Filter
Color (Custom)*1 Brightness
4-3. Color Adjustment (p.32)
Temperature
Gamma
Saturation
Hue
Gain
6 Colors
Unlock
Reset
**
*
PowerManager
Others
DVI DMPM
VESA DPMS
Screen Size
Border Intensity
Input Priority
Off Timer
4-4. Power-save Setup (p.34)
4-2. Displaying Low Resolutions (p.30)
Select the priority input signal. (p.20)
Set the monitor’s off timer to on or off. (p.24)
Set the monitor’s beeper to on or off. (p.46)
Change the size of the menu.
Beep
Menu Size
Menu
Settings
Menu Position
Menu Off Timer
Translucent
Adjust the menu position
Set the menu displaying time.*2
Set the transparency of the background.
Orientation
Change the orientation of the
ScreenManager for monitor’s portrait
position.
Power Indicator
Make non-light for blue lighting when the
screen is displayed. (p.25)
Reset
Return to the factory default settings. (p.46)
Information
Language
Information
Review the ScreenManager’s settings,
model name, serial number and usage
time*3.
English, German, French,
Spanish, Italian, Swedish and
Japanese
Select the ScreenManager’s language.
*1The adjustable functions depend on the selected FineContrast mode. (see page 32).
*2The displaying time of the FineContrast Menu cannot be changed.
*3Due to the inspection on the factory, the usage time may not be “0 hour” at shipping.
22 3. ScreenManager
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-3. FineContrast
This function allows you to select the best suited mode for screen display.
To select the Mode
Pressing the Mode button allows you to select the best suited mode for screen display
from 6 FineContrast modes; “Custom”, “sRGB”, “CAL”, “Text”, “DICOM-CL” and
“DICOM-BL”. Color settings each mode can be adjusted by using the <Color> menu of
the ScreenManager.
Exit
Press the Enter Button to exit the menu.
FineContrast Menu
[Ex.] Custom
Mode Button
Enter Button
Current Mode
Setting status of
Brightness, Temperature
and Gamma
FineContrast Mode
Selectable FineContrast modes are as follows.
Custom
sRGB
To adjust the color settings according to your preference
To display the screen images based on those original colors (ex. over
the Internet)
CAL
The mode only for calibration
Text
Text on word processor or spreadsheet software
Suitable for Clear Base X-ray Film
Suitable for Blue Base X-ray Film
DICOM-CL
DICOM-BL
Color Adjustment of the Mode Settings
<Brightness>, <Temperature> and <Gamma> settings can be adjusted on the
FineContrast Menu. Select the desired function icon with the Up/Down Control Buttons
and adjust with the Left/Right Buttons. (Setting(s) of <Temperature> and/or <Gamma>
is defined as standard default in some modes. (p.32))
Detailed Adjustments
The detailed color settings of each mode can be adjusted by using the <Color> menu of
the ScreenManager. (p.32)
3. ScreenManager 23
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3-4. Useful Functions
Adjustment Lock
Use the “Adjustment Lock” function to prevent any accidental changes.
Locked function
• Adjustments and settings in the ScreenManager.
• Auto Adjustment Button
• Selecting of the FineContrast mode by the Mode Button /
Adjustment.
Unlocked function
• Input Signal Selection Button
[To lock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Press on the Auto adjustment button while switching on the monitor’s power.
[To unlock]
(1) Switch off the monitor’s power by the power button on the control panel.
(2) Hold down the Auto adjustment button once again and turn the power back on.
Off Timer
The off timer function causes the monitor to automatically enter a power off state after
a predetermined amount of time has lapsed. This function was created to reduce
afterimage (p.48) characteristics that are particular to LCD monitors when the monitor
screen is left on for a long period without use.
[Procedure]
(1) Select <Off Timer> in the ScreenManager <Others> menu.
(2) Select “Enable” and press the Right and Left Buttons to adjust the “On Period” (1
to 23 hours).
[Off Timer system]
PC
Monitor
Power Indicator
On Period (1H - 23H)
Last 15 min. in "On period"
"On period" expired
Operation
Blue
Advance Notice *1
Blue Flashing
Power off
Flashing yellow slowly
*1Advance notice (Power Indicator flashing blue) will be given 15 minutes before the monitor
automatically enters the “Power Off” mode. To delay entering the “Power Off” mode, press the
Power Button during the advance notice period. The monitor will continue to operate for an
additional 90 minutes.
[Power Resumption Procedure]
Press the Power Button to return to a normal screen.
NOTE
• The off timer function works while the PowerManager is active, but there is no
advance notice before the monitor’s power is switched off.
24 3. ScreenManager
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Power Indicator Setting
Light off the power indicator. This function is available for the multiple panels settings.
[Procedure]
(1) Select <Power Indicator> in the ScreenManager <Others> menu.
(2) Select “Disable”.
Sync Switch Setting
Correct the greenish screen caused by the input signal timing.
[To set]
(1) Switch off the monitor’s power by the main power switch.
(2) Press on the down button while switching on the monitor’s main power switch
again.
(3) The Sync Switch setting has been changed.
[To cancel]
(1) Switch off the monitor’s power by the main power switch.
(2) Press on the down button while switching on the monitor’s main power switch
again.
(3) The Sync Switch setting has been cancelled.
EIZO Logo Disappearing Function
When switching on the Power Button on the control panel, the EIZO logo is displayed
for a while. If you desire to display or undisplay this logo, use this function. (Default is
logo appearing.)
[To undisplay]
Switch off the monitor’s power by the Power Button on the control panel, then hold
down the Enter Button once again and turn the power back on.
[To display again]
Switch off the monitor’s power by the Power Button, then hold down the Enter
Button once again and turn the power back on.
3. ScreenManager 25
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. ADJUSTMENT
The monitor displays the digital input image correctly based on its pre-setting
data.
4-1. Screen Adjustment
NOTE
• Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments.
Analog Input
Screen adjustments for the LCD monitor should be used in suppressing screen flickering
and also for adjusting the screen to its proper position. There is only one correct
position for each display mode. It is also recommended to use the ScreenManager
function when first installing the display or whenever changing the system. For
convenience, an easy set-up Program installed on the utility disk to assist in the set-up
procedure is provided.
Adjustment Procedure
1. Press the Auto Adjustment Button on the control panel.
The message “Your setting will be lost, if you press again now.” appears and
remains on the screen for 5 seconds. While the message is on the screen, press the
Auto Adjustment Button again to automatically adjust the clock, phase, screen
position and resolution. If you do not wish to do adjust the screen, do not press
the Auto Adjustment Button again.
NOTE
• The Auto Adjustment function is intended for use on the Macintosh and on
AT-compatible PC running Windows. It may not work properly in either of the
following cases.
When running an AT-compatible PC on MS-DOS (Not windows). The
background color for the “wall paper” or “desktop” pattern is set to black.
If the appropriate screen cannot be made by using the Auto Adjustment
Button, adjust the screen through the following procedures. If the
appropriate screen can be made, proceed to step 4.
2. Run the “Screen adjustment program”.
Having read the “Readme.txt” file, run the “Screen adjustment program” in the
enclosed EIZO LCD Utility Disk. Step by step, adjustment is provided by the
wizard guide. (If using the Windows, the program can be directly run from the
menu screen of the CD-ROM.)
26 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
NOTE
•If the user’s operating system has no utility disk (e.g. OS/2), we recommend
setting the desktop pattern to that as shown in the diagram on the following.
3. Adjust by using <Screen> menu in the ScreenManager.
(1) Vertical bars appear on the screen
→
Use the <Clock> (p.48) adjustment.
Select the “Clock” and eliminate the vertical bars by using the Right and Left
of the Control Buttons. Do not continuously press the Control Buttons, as the
adjustment value will change quickly and make it difficult to locate the most
suitable adjustment point.
If the horizontal flickering, blur or bars appear, proceed to “Phase” adjustment
as follows.
(2) Horizontal flickering, blurring or bars appear on the screen.
→
Use the <Phase> (p.49) adjustment.
Select the <Phase> and eliminate the horizontal flickering, blurring or bars by
using the Right and Left Buttons.
NOTE
• Horizontal bars may not completely disappear from the screen depending on
the PC.
4. ADJUSTMENT 27
Download from Www.Somanuals.com. All Manuals Search And Download.
English
(3) The screen position is not incorrect.
Use the <Position> adjustment.
→
The correct displayed position of the monitor is decided because the number
and the position of the pixels are fixed. The <Position> adjustment moves the
image to the correct position.
Select <Position> and adjust the position of the upper left corner of the image
by using the Up, Down, Right and Left Buttons in order to align the screen.
If vertical bars of distortion appear after finishing the <Position> adjustment,
return to <Clock> adjustment and repeat the previously explained adjustment
procedure (“Clock” → “Phase” → “Position”)
(4) Screen image is smaller or larger than the actual screen images.
→
Use the <Resolution> adjustment.
Adjustment is needed when the input signal resolution and the resolution now
being displayed are different.
Select <Resolution> and confirm if the resolution now being displayed is the
same as the input resolution. If it is not, adjust the vertical resolution using the
Up and Down Button and adjust the horizontal resolution using the Right and
Left Buttons.
Smaller than the actual screen images.
Adjusted to actual screen
Larger than the actual screen images.
28 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. Adjust the output signal range (Dynamic Range) of the signal.
Use the <Range Adjustment> (p.49) of <Screen> menu.
→
This controls the level of output signal range to display the whole color gradation
(256 colors).
[Procedure]
Select the <Range Adjustment> in the ScreenManager and press the Auto
Adjustment button on the control panel to adjust the Range Adjustment. The
screen blanks for a moment and adjusts the color range to display the whole color
gradation of the current output signal.
4. ADJUSTMENT 29
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4-2. Displaying Low Resolutions
The lower resolutions are enlarged to full screen automatically. Using the <Screen Size>
function in the <Others> menu enables to change the screen size.
1. Enlarge the screen size when displaying a low resolution.
→
Select the <Screen Size>.
Select the <Screen Size> in the others menu and select the screen size by using the
Up and Down Buttons.
Menu
Function
Displays the picture on the screen in full, irrespective of the picture’s
resolution. Since the vertical resolution and the horizontal resolution
are enlarged at different rates, some images may appear distorted.
Full
Displays the picture on the screen in full, irrespective of the picture’s
resolution. Since the vertical resolution and horizontal resolution are
enlarged at same rates, some horizontal or vertical image may
disappear.
Enlarged
Normal
Displays the picture at the actual Screen resolution.
Example: Displaying 1024 x 768
Normal
Enlarged
Full (Default Setting)
(1024×768)
(1280×1024)
(1280×960)
2. Smooth the blurred texts of the enlarged screen.
Switch the <Smoothing> setting.
→
Select the suitable level from 1 – 5 (Soft – Sharp).
Select <Smoothing> in the <Screen> menu and adjust by using the Right and Left
Buttons.
NOTE
• <Smoothing> is disabled when the screen is displayed in the following
resolutions.
*1280 x 1024
*The image size is doubled both in horizontally and vertically to (i.e. 1280 x 960
enlarged from 640 x 480) provide clear focus which does not require this
function.
30 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. Set the brightness of the black area surrounding the displayed image.
→
Set the <Border Intensity>.
In the <Enlarge> mode or <Full Screen> mode, the outer area (border) is usually
black.
Select <Border Intensity> in the <Others> menu and adjust by using the Right and
Left Buttons.
Border
4. ADJUSTMENT 31
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4-3. Color Adjustment
Color settings of each FineContrast mode can be adjusted and saved by using the
<Color> menu of the ScreenManager.
In the analog input, perform the “Range Adjustment” (p.29) before making the
color adjustments.
Adjustment items
The adjustable items and displayed icons on the ScreenManager depend on the selected
FineContrast mode.
“√”: Settable/Adjustable “−”: Fixed at the factory
Icons
Functions
FineContrast Modes
Custom
sRGB
CAL
Text
DICOM- DICOM-
CL
BL
√
√
√
√
Brightness
*
*
√
√
√
√
−
√
√
−
Temperature
−
−
−
−
−
−
−
−
Gamma
*
√
√
−
−
Saturation
−
−
√
−
Hue
√
−
−
−
−
−
−
√
Gain
√
−
−
−
6 colors
Unlock
−
√
−
−
−
−
−
−
−
Reset
√
−
√
−
−
*These settings can be also adjusted on the FineContrast menu. (p.23)
NOTE
• Allow the LCD monitor to stabilize for at least 20 minutes before making image
adjustments. (Allow the monitor to warm up for at least 20 minutes before making
adjustments.)
• Performing the <Reset> of the <Color> menu returns the color settings of the
selected mode to the default settings.
• The values shown in percentages represent the current level within the specific
adjustment. They are available only as a reference tool. (To create a uniform white
or black screen, the percentages for each will probably not be the same.)
32 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Adjustment Contents
Menu
Brightness
Function Descriptions
Adjustable Range
0 ∼ 130%
To set the brightness of the
screen
Temperature
(p.49)
To set the color temperature
4,000 ∼ 15,000 K
in 500 K increments (including
9,300 K). Default setting is 7,500K.
NOTE
• The values shown in the Kelvin are available only as a reference tool.
• Adjusting the <Gain> turns the <Temperature> adjustment "Off".
• Setting the temperature under 4,000 K or over 15,000 K invalidates the
color temperature setting. (The color temperature’s setting turns “OFF”.)
Gamma (p.49)
Saturation
To set the gamma value
1.8 ∼ 2.6
NOTE
• If setting the gamma value, the using the monitor in the digital signal input
is recommended.
If using the monitor in the analog input signal, set the gamma value from
1.8 to 2.2.
To change the saturation
-16 ∼ 16
Setting the minimum level (-16)
turns the image to the
monochrome.
NOTE
• The <Saturation> adjustment may cause undisplayable color tone.
Hue
To change the flesh color, etc.
-20 ∼ 20
NOTE
• The <Hue> adjustment may cause undisplayable color tone.
Gain (p.48)
To change each color (red, green
and blue)
0 ∼ 100%
By adjusting the red, green and
blue color tones for each mode,
custom colors can be defined.
Display a white or gray background
image and adjust the <Gain>.
NOTE
• The values shown in the percentage are available only as a reference
tool.
• Setting the <Temperature> (p.49) invalidates the <Gain> adjustment.
<Gain> setting returns to the defaul.
6 colors
To adjust <Saturation> and
<Hue> in each color (Red, Yellow,
Green, Cyan, Blue and Magenta)
Hue: -20 ∼ 20
Saturation: -16 ∼ 16
Unlock
Reset
Unlock the lock at the CAL mode.
Select <Unlock>. (p.34)
To return the color settings of the
selected mode to the default
settings
Select the <Reset>.
4. ADJUSTMENT 33
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Unlock Function after Calibration
The calibration is available when using the specified optional calibration kit. (p.47)
After the calibration in FineContrast CAL mode, the brightness adjustment function is
automatically locked. Unlock function is available by using ScreenManager.
How to unlock
(1) Select the <Unlock> of <Color> menu.
(2) Select “Unlock”.
NOTE
• Performing the <Reset> of <Others>, locked function is also unlocked.
• After the unlock, the <Unlock> is disabled.
34 4. ADJUSTMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4-4. Power-save Setup
The <PowerManager> menu in the ScreenManager enables to set the power-save setup.
NOTE
• Do your part to conserve energy, turn off the monitor when you are finished using it.
Disconnecting the monitor from the power supply is recommended to save energy
completely.
• Even if the monitor is in a power saving mode, USB compliant devices function
when they are connected to the monitor’s USB (both the upstream and the
downstream ports). Therefore, power consumption of the monitor will change
according to the connected devices even if the monitor is in a power saving mode.
Analog Input
This monitor complies with the “VESA DPMS” (p.49).
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “VESA DPMS” in the <PowerManager> menu.
[Power saving system]
PC
Monitor
Power Indicator
Operation
Operation
Blue
STAND-BY
Power saving
SUSPEND
OFF
Power saving
Yellow
[Procedure]
Operate the mouse or keyboard to return to a normal screen.
Digital input
This monitor complies with the “DVI DMPM” (p.48).
[Procedure]
(1) Set the PC’s power saving settings.
(2) Select “DVI DMPM” in the <PowerManager> menu.
[Power saving system]
PC
On
Monitor
Operation
Power Indicator
Blue
Power saving
Power saving
Yellow
Flashing yellow
(2 times for each)
Off mode
Power saving*1
*1Power saving through the PC’s off mode is only supported when “Manual” is selected on the
ScreenManager’s <Input Priority>.
[Procedure]
Operate the mouse or keyboard to return to a normal screen.
Power on the PC to return a normal screen from the Off mode of the PC.
4. ADJUSTMENT 35
Download from Www.Somanuals.com. All Manuals Search And Download.
English
5. MAKING USE OF USB
(Universal Serial Bus)
This monitor provides a hub which supports the USB standard. When connecting to a
USB compliant PC or another hub, the monitor functions as a hub to which the USB
compliant peripherals can be easily connected.
Required system environment
• PC equipped with USB ports or another USB hub connected to the USB compliant PC
• Windows 98/2000/Me/XP // Mac OS 8.5.1 or later
• USB Cable (MD-C93, enclosed)
NOTE
• The USB hub function may not work properly depending on the PC or peripherals.
Please consult the manufacturer of each device about the USB support.
• Using the USB Rev. 2.0 compatible PC or peripherals is recommended.
• When the monitor is not on, the peripherals connected to the downstream ports will
not operate.
• Even if the monitor is in a power saving mode, the devices connected to the
monitor’s USB ports (both the upstream and the downstream) will function.ᴾ
• The followings are procedures for the Windows 98/Me/2000/XP and Mac OS.
Connecting to the USB HUB
1. Connect the monitor to the PC with the signal cable (p.13) first, then
turn on the PC.
2. Connect the upstream port of the monitor to the downstream port of
the USB compliant PC or another hub by using the USB cable.
Upstream Ports
Upstream port:
Connect the USB compliant PC or
another hub using the USB cable.
To Downstream Ports of
the PC or Another Hub
After connecting the USB cable, the USB function can be set up automatically.
36 5. MAKING USE OF USB (Universal Serial Bus)
Download from Www.Somanuals.com. All Manuals Search And Download.
English
3. After setting up, the monitor’s USB hub is available for connecting
USB compliant peripherals to the downstream ports of the monitor.
Connecting Examples
USB
Cable
Scanner
Monitor
Keyboard
PC
Mouse
Downstream
Downstream ports:
Connect the cables from USB
compliant peripherals such as a
mouse, keyboard, etc.
Scanner
Keyboard
ScreenManager Pro for LCD (for Windows)
For further details about the “ScreenManager Pro for LCD (for Windows)”, refer to the
EIZO LCD Utility Disk.
5. MAKING USE OF USB (Universal Serial Bus) 37
Download from Www.Somanuals.com. All Manuals Search And Download.
English
6. ATTACHING AN ARM
The LCD monitor can be used with an arm by removing the tilt stand and attaching the
arm or stand to the LCD monitor.
NOTE
• If you will use the arm or stand of other manufacturers, confirm the followings to the
manufacturers before selecting.
- Hole spacing on the arm mounting: 100 mm x 100 mm (VESA compliant)
- Supportable Weight: Total weight of the monitor (without stand) and attaching
equipment such as a cable
- TÜV/GS approved arm or stand
• Please connect cables after attaching an arm stand.
Setup Procedure
1. Hold the center of the stand mounting cover and slide them
rightward or leftward to remove the mounting cover.
Stand mounting cover
2. Lay the LCD monitor down. Do not scratch the panel.
3. Remove the tilt stand by loosening the screws.
(4 pcs of M4 x 15 BZn/Fe)
38 6. ATTACHING AN ARM
Download from Www.Somanuals.com. All Manuals Search And Download.
English
4. Attach an arm stand to the LCD monitor securely.
Arm-stand
M4 Mounting Screws: M4 x 15 (mm) BZn/Fe
6. ATTACHING AN ARM 39
Download from Www.Somanuals.com. All Manuals Search And Download.
English
7.TROUBLESHOOTING
If a problem persists even after applying the suggested remedies, contact an EIZO dealer.
• No picture problems → See No.1 ~ No.2
• Imaging problems → See No.3 ~ No.14
• Other problems → See No.15 ~ No.20
• USB problems → See No.21 ~ No.22
Problems
1. No picture
Points to check with possible solutions
†ꢀCheck that the power cord is correctly connected.
If the problem persists, turn off the monitor power
for a few minutes, then turn it back on and try
again.
• Indicator status: Off
†ꢀCheck the “Brightness” setting.
• Indicator status: Blue
†ꢀSwitch the signal input by pressing the Input Signal
• Indicator status: Yellow
Selection Button on the front control panel.
†ꢀTry pressing a key on the keyboard, or clicking the
mouse.
(p.35)
• Indicator status: Slowly flashing
†ꢀTry pressing the Power Button.
†ꢀTry turning the PC on.
Yellow
• Indicator status: Flashing Yellow
(twice for each)
These messages appear when the signal is not inputted
correctly, even if the monitor functions properly.
2. Error messages shown below
will remain on the screen for 40
seconds.
†ꢀWhen the image is displayed correctly after a short
time, there is no problem with the monitor. (Some
PCs do not output the signal soon after powering
on.)
†ꢀCheck that the PC is turned ON.
†ꢀCheck that the signal cable is properly connected to
the PC or graphics board.
†ꢀSwitch the signal input by pressing the Input Signal
Selection Button on the front control panel.
†ꢀUse the graphics board’s utility software to change
the frequency setting. (Refer to the manual of the
graphics board.)
• Whenever an error signal message
appears, the signal frequency will be
displayed in red.
(Example)
40 7. TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Problems
Points to check with possible solutions
†ꢀAdjust the image position using the <Position>
3. Display position is incorrect.
(p.28)
†ꢀIf the problem persists, use the graphics board’s
utility software to change the display position if
available.
†ꢀAdjust the resolution using the <Resolution>.
4. Screen image is smaller or larger
than the actual screen images.
(p.28)
†ꢀDecrease the vertical bars using the <Clock>. (p.27)
5. Vertical bars of distortion appear.
†ꢀAdjust the characters and images using the <Signal
6. The characters and images have
several vertical bars on their
right side.
Filter>.
†ꢀDecrease the horizontal bars using the <Phase>.
7. Horizontal bars of distortion
appear.
(p.27)
†ꢀAdjust the blurred lines using <Smoothing> (p.30)
8. Letters and lines appear blurred.
†ꢀThis happens when both composite (X-OR) input
signal and separate vertical synchronizing signal are
input. Please select one of the two.
9. Distortion appears like the figure
below.
7. TROUBLESHOOTING 41
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Problems
Points to check with possible solutions
†ꢀAdjust the <Brightness> (The backlight of the LCD
monitor has a fixed life span. When the screen
becomes dark or begins to flicker, please contact
your dealer.)
10. The screen is too bright or too
dark.
†ꢀSome input signal timing causes greenish screen.
Change the Sync Switch setting. (p.25).
†ꢀWhen the screen image is changed after displaying
the same image for a long period, an afterimage
may appear. The “Afterimage” can be removed
gradually by changing the displayed image. Use the
“Off Timer” function and avoid keeping the screen
on all the time. (p.24)
11. Afterimages appear.
†ꢀThis is due to the characteristics of the panel itself
12. The screen has defective pixels
(e.g. slightly light or dark).
and not the LCD product.
†ꢀLeaving the screen white may solve the problem.
13. Fingerprints remain on the
screen.
†ꢀChange the mode in <Signal Filter> in the <Screen>
14. The noise appears on the screen.
menu.
†ꢀ<Smoothing> is disabled when the screen is
15. The <Smoothing> cannot be
selected.
displayed in the 1280 x1024.
†ꢀ<Smoothing> is disabled when “Normal” is
selected in the <Screen Size> menu.
†ꢀThe image size is doubled both in horizontally and
vertically to (i.e. 1280 x 960 enlarged from 640 x
480) provide clear focus which does not require
this function.
†ꢀThe adjustment lock is probably on. (p.24)
16. The Main menu of
ScreenManager does not
operate.
†ꢀCheck that the FineContrast mode is not activated.
(p. 21)
†ꢀThe Auto adjustment button does not operate
17. The Auto Adjustment Button
does not operate.
when the digital signal is input.
†ꢀThe adjustment lock is probably on. (p.24)
†ꢀThe adjustment lock is probably on. (p.24)
18. The Mode Button does not
operate.
42 7. TROUBLESHOOTING
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Problems
Points to check with possible solutions
†ꢀAfter the calibration, the brightness adjustment
function is automatically locked. Please refer to
page 34 to unlock.
19. The <Brightness> cannot be
selected in FineContrast CAL
mode.
†ꢀUse the graphics board’s utility software to change
20. Frequency does not change after
installing “Monitor information
file” in the attached utility disk
on Windows 98/2000/Me/XP.
the input signal frequency.
†ꢀCheck that the USB cable is correctly connected.
21. PC is hung up. / The peripherals
connected to the downstream
ports do not operate.
†ꢀCheck the downstream ports by connecting the
peripherals to other downstream ports. If the
problem is solved by doing this, contact an EIZO
dealer. (For details, refer to the manual of the PC.)
†ꢀTry executing the following method.
- Restarting the PC
- Connecting the PC and peripherals directly
If the problem is solved by doing this, contact an
EIZO dealer.
†ꢀCheck that the USB cable is correctly connected.
22. USB function cannot be setup.
†ꢀCheck that the PC and OS are USB compliant. (For
verification of USB support, consult the
manufacturer of each system.)
†ꢀCheck the PC’s BIOS setting for USB. (For details,
refer to the manual of the PC.)
7. TROUBLESHOOTING 43
Download from Www.Somanuals.com. All Manuals Search And Download.
English
8. CLEANING
Periodic cleaning is recommended to keep the monitor looking new and to prolong its
operation lifetime.
NOTE
• Never use thinner, benzene, alcohol (ethanol, methanol, or isopropyl alcohol),
abrasive cleaners, or other strong solvents, as these may cause damage to the
cabinet or LCD panel.
Cabinet
To remove stains, wipe the cabinet with a soft, lightly moistened cloth using a mild
detergent. Do not spray wax or cleaner directly into the cabinet. (For details, refer to
the manual of the PC.)
LCD Panel
• The LCD surface can be cleaned with a soft cloth, such as cotton or lens paper.
• If necessary, stubborn stains can be removed by moistening part of a cloth with water
to enhance its cleaning power.
44 8. CLEANING
Download from Www.Somanuals.com. All Manuals Search And Download.
English
9. SPECIFICATIONS
LCD Panel
48 cm (19.0 inch), TFT color LCD panel with Anti-Glare Hard
Coating 2H, Viewing Angle: Horizontal: 170°, Vertical: 170°
(CR≥10)
Dot Pitch
0.294 mm
Horizontal Scan Frequency
Analog: 30 ∼ 82 kHz (Automatic)
Digital: 31 ~ 76 kHz
Vertical Scan Frequency
Analog: 49 ∼ 86 Hz (Automatic) (1280 x 1024: 49 ∼ 75 Hz)
Digital: 59 ~ 61 Hz, (VGA TEXT: 69 ~ 71 Hz)
Resolution
1M pixels (1280 dots × 1024 lines)
Dot Clock (Max.)
Analog: 135 MHz
Digital: 108 MHz
Display Colors
Display Area
16 million colors (max)
376 mm (H) × 301 mm (V) (14. 8” (H) × 11.9” (V))
100-120/200-240 VAC 10%, 50/60 Hz, 0.6-0.5A /0.35-0.3 A
Power Supply
Power Consumption
Min.: 55 W
Max.: 60 W (With USB)
Power Saving Mode: Less than 8 W (for single signal input
without USB)
Input Connector
DVI-I × 2
Analog Input Signal (Sync)
a) Separate, TTL, Positive/Negative
b) Composite, TTL, Positive/Negative
c) Sync on Green, 0.3 Vp-p, Negative
0.7Vp-p/75Ω Positive
Analog Input Signal (Video)
Input Signal (Digital)
Signal registration
TMDS (Single Link)
Analog: 45 (Factory preset: 26)
Digital: 10 (Factory preset: 0)
Plug & Play
VESA DDC 2B
Dimensions with stand
414 mm (W) x 409.5∼ 509.5 mm (H) x 202.7 mm (D)
(16.3”(W) x 16.1” ∼ 20.1” (H) x 8.0”(D))
without stand
414mm (W) x 340mm (H) x 64mm (D)
(16.3”(W) x 13.4”(H) x 2.52”(D))
Weight
with stand
8.1 kg (17. 9 lbs.)
5.8 kg (12.8 lbs.)
without stand
Environment Temperature
Conditions
Operating: 0 °C ∼ 35 °C (32 °F ∼ 95 °F)
Storage: -20 °C ∼ 60 °C (-4 °F ∼ 140 °F)
Humidity
Pressure
30 % to 80 % R.H. Non-condensing
860 to 1,060 hPa
USB
Standard
Rev. 2.0 complied self-powered hub
Upstream port × 1, Downstream port × 2
USB ports
Communication 480 Mbps (high), 12 Mbps (full), 1.5 Mbps (low)
Speed
Power Supply
Downstream: 500 mA for each (Max.)
9. SPECIFICATIONS 45
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Certifications and Standards
Classification of Equipment
TÜV Rheinland /GM, CB, NRTL/C-TÜV, CE (93/42/EEC),
FCC-B
Type of protection against electric shock: Class I
EMC class: EN60601-1-2: 2001 Group 1 Class B
Classification of medical device (MDD 93/42/EEC): Class I
Default Settings
Analog input
Custom
100%
Digital input
DVI DMPM
FineContrast Mode
Brightness
Temperature
Smoothing
7,500K
3
PowerManager
Screen Size
Input Priority
Off Timer
VESA DPMS
Full
1
Disable
Normal
45 seconds
On
Menu Settings
Menu Size
Menu Off Timer
Beep
Language
English
Beeper Settings
Short beep
ScreenManager item selected.
ScreenManager parameter adjusted to minimum or maximum limit.
Input Signal Selection Button pressed.
Auto Adjustment Button pressed.
Long beep
ScreenManager data-save executed.
Monitor not connected correctly.
4 short beeps
PC turned off.
Monitor received unsupported signal frequency.
2 short beeps every
15 sec.
Monitor is in the advance notice mode of the Off Timer. The power
will be off within fifteen minutes.
46 9. SPECIFICATIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Dimensions
mm (inches)
SIDE
TOP
FRONT
Pin Assignment
DVI-I Connector
3
1
9
17
2
4
12
20
6
7
8
16
24
5
13
21
C1 C2
10 11
19
14 15
22 23
C3 C4
C5
18
Pin No.
Signal
Pin No.
Signal
Pin No.
Signal
1
2
3
TMDS Data2-
TMDS Data2+
TMDS Data2/4 Shield
11
12
13
TMDS Data1/3 Shield
21
22
23
NC
NC
NC
TMDS Clock shield
TMDS Clock+
4
5
NC*
NC
14
+5V Power
24
C1
TMDS Clock-
Analog Red
15 Ground (return for +5V,
Hsync and Vsync)
6
7
8
9
DDC Clock (SCL)
DDC Data (SDA)
Analog Vertical Sync
TMDS Data1-
16
17
18
19
Hot Plug Detect
TMDS Data0-
TMDS Data0+
C2
C3
C4
C5
Analog Green
Analog Blue
Analog Horizontal Sync
TMDS Data0/5 Shield
Analog Ground
(analog R, G, & B return)
(*NC: No Connection)
10
TMDS Data1+
20
NC
USB Port
No.
Signal
Signal
Upstream Downstream
1
2
3
VCC
- Data
+ Data
Cable power
Serial data
Serial data
4
Ground
Cable Ground
Series B
Series A
Optional
Calibration Kit
RadiCS RX1
9. SPECIFICATIONS 47
Download from Www.Somanuals.com. All Manuals Search And Download.
English
10. GLOSSARY
Afterimage
The Afterimage is particular to LCD monitors when the monitor screen is left on for a
long period without use. The “Afterimage” can be removed gradually by changing
the displayed image.
Clock
With the analog input signal display, the analog signal is converted to a digital signal
by the LCD circuitry. To convert the signal correctly, the LCD monitor needs to
produce the same number clock pulse as the dot clock of the graphics system. When
the clock pulse is not correctly set, some vertical bars of distortion are displayed on
the screen.
DICOM
(Digital Imaging and Communication in Medicine)
The DICOM standard was developed by the American College of Radiology and the
National Electrical Manufacturer’s Association of the USA.
The DICOM compatible device connection enables to transfer the medical image and
information. The DICOM, Part 14 document defines the digital, grayscale medical
image display.
DVI
(Digital Visual Interface)
A digital flat panel interface. DVI can transmit digital data from the PC directly
without loss with the signal transition method “TMDS”.
There are two kinds of DVI connectors. One is DVI-D connector for digital signal
input only. The other is DVI-I connector for both digital and analog signal inputs.
DVI DMPM
(DVI Digital Monitor Power Management)
The Power management system for the digital interface. The “Monitor ON” status
(operation mode) and the “Active Off” status (power-saving mode) are indispensable
for the DVI-DMPM as the monitor’s power mode.
Gain Adjustment
Adjusts each color parameter for red, green and blue. The color of the LCD monitor
is displayed through the color filter of the LCD panel. Red, green and blue are the
three primary colors. The colors on the monitor are displayed by combining these
three colors. The color tone can change by adjusting the illumination amount passed
through each color’s filter.
48 10. GLOSSARY
Download from Www.Somanuals.com. All Manuals Search And Download.
English
Gamma
Generally, the relationship that the light intensity values of a monitor change
nonlinearly to the input signal level is called “Gamma Characteristic”. On the
monitor, low gamma values display the whitish images and high gamma values
display the high contrast images.
Phase
The phase adjustment decides the sampling timing point for converting the analog
input signal to a digital signal. Adjusting the phase after the clock adjustment will
produce a clear screen.
Range Adjustment
The Range Adjustment controls the level of output signal range to display the whole
color gradation.
Resolution
The LCD panel consists of a fixed number of pixel elements which are illuminated to
form the screen image. The EIZO R12 display panel consists of 1280 horizontal
pixels and 1024 vertical pixels. At a resolution of 1280 x 1024, all pixels are
displayed as a full screen.
sRGB (Standard RGB)
“International Standard for Red, Green and Blue color space”
A color space was defined with the aim of the color matching between applications
and hardware devices, such as monitors, scanners, printers and digital cameras. As a
standard default space, sRGB allows Internet users to closely match colors.
Temperature
Color temperature is a method to measure the white color tone, generally indicated in
degrees Kelvin. At high temperatures the white tone appears somewhat blue, while at
lower temperatures it appears somewhat red. Computer monitors generally give best
performance at high temperature settings.
5,000 K: Slightly reddish white.
6,500 K: Warm-white tone, similar to white paper or daylight.
9,300 K: Slightly bluish white.
TMDS
(Transition Minimized Differential Signaling)
A signal transition method for the digital interface
VESA DPMS
(Video Electronics Standards Association – Display Power Management Signaling)
The acronym VESA stands for “Video Electronics Standards Association” and DPMS
stands for “Display Power Management Signaling.” DPMS is a communication
standard that PCs and graphics boards use to implement power savings on the
monitor side.
10. GLOSSARY 49
Download from Www.Somanuals.com. All Manuals Search And Download.
English
MEMO
50 MEMO
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX/ANHANG/ANNEXE
Preset Timing Chart for Analog input
Timing-Übersichten für Analog Eingang
Synchronisation des Signaux pour Analog numerique
Based on the signal diagram shown below 26 factory presets have been registered in the
monitor's microprocessor.
Der integrierte Mikroprozessor des Monitors unterstützt 26 werkseitige
Standardeinstellungen (siehe hierzu die nachfolgenden Diagramme).
26 signaux ont été enregistrés en usine dans le microprocesseur du moniteur,
conformément au diagramme de synchronisation ci-dessous.
Dot Clock
MHz
Frequencies
H kHz
Sync Polarity
Mode
V Hz
59.94
70.09
66.67
74.55
75.06
74.76
72.81
75.00
85.01
59.94
56.25
60.32
72.19
75.00
85.06
60.00
70.07
75.03
85.00
75.00
60.00
60.02
75.03
66.10
76.20
67.20
H
V
VGA 640 × 480 @60 Hz
VGA 720 × 400 @70 Hz
25.2
28.3
30.2
57.3
100.0
126.2
31.5
31.5
36.0
28.3
36.0
40.0
50.0
49.5
56.3
65.0
75.0
78.8
94.5
108.0
108.0
108.0
135.0
94.2
107.5
117.0
31.47
31.47
35.00
49.73
68.68
74.76
37.86
37.50
43.27
31.47
35.16
37.88
48.08
46.88
53.67
48.36
56.48
60.02
68.68
67.50
60.00
63.98
79.98
62.00
71.90
71.70
Nega.
Nega.
Nega.
Posi.
Nega.
Posi.
Nega.
Posi.
Nega.
Posi.
Nega.
Nega.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Nega.
Macintosh 640 × 480 @67 Hz
Macintosh 832 × 624 @75 Hz
Macintosh 1152 × 870 @75 Hz
Macintosh 1280 × 960 @75 Hz
VESA 640 × 480 @72 Hz
VESA 640 × 480 @75 Hz
VESA 640 × 480 @85 Hz
VESA 720ą480@60Hz
VESA 800 × 600 @56 Hz
VESA 800 × 600 @60 Hz
VESA 800 × 600 @72 Hz
VESA 800 × 600 @75 Hz
VESA 800 × 600 @85 Hz
VESA 1024 × 768 @60 Hz
VESA 1024 × 768 @70 Hz
VESA 1024 × 768 @75 Hz
VESA 1024 × 768 @85 Hz
VESA 1152 × 864 @75 Hz
VESA 1280 × 960 @60 Hz
VESA 1280 × 1024 @60 Hz
VESA 1280 × 1024 @75 Hz
SUN WS 1152 × 900 @66 Hz
SUN WS 1152 × 900 @76 Hz
SUN WS 1280 × 1024 @67 Hz
Nega.
Posi.
Nega.
Nega.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Posi.
Posi.
Posi.
Posi.
Posi.
Posi.
Nega.
Nega.
Nega.
i
APPENDIX/ANHANG/ANNEXE
Download from Www.Somanuals.com. All Manuals Search And Download.
For U.S.A, Canada, etc. (rated 100-120 Vac) Only
FCC Declaration of Conformity
We, the Responsible Party
EIZO NANAO TECHNOLOGIES INC.
5710 Warland Drive, Cypress, CA 90630
Phone: (562) 431-5011
declare that the product
Trade name: EIZO
Model: RadiForce R12
is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures.
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note
Use the attached specified cable below or EIZO signal cable with this monitor so as to keep
interference within the limits of a Class B digital device.
- AC Cord
- Shielded Signal Cable (enclosed)
Canadian Notice
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de le classe B est comforme à la norme NMB-003 du Canada.
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycle Auskunft
Die Rücknahme dieses Produktes nach Nutzungsende übernimmt EIZO in Deutschland
zusammen mit dem Partner MIREC GmbH & Co. KG. Dort werden die Geräte in ihre
Bestandteile zerlegt, die dann der Wiederverwertung zugeführt werden. Um einen
Abholtermin zu vereinbaren und die aktuellen Kosten zu erfahren, benutzen Sie bitte folgende
Rufnummer: 02153-73 35 00. Weitere Informationen finden Sie auch unter der Internet-
Recycling Information for customers in Switzerland:
All recycling information is placed in the SWICO’s website.
Recycling-Information für Kunden in der Schweiz:
Alle Informationen zum Thema Recycling finden Sie auf der Homepage des Brancheverbandes
SWICO.
Renseignements de recyclage pour les clients en Suisse:
Vous trouvez tous les renseignements pour le sujet de recyclage sur la page WEB de I’UNION
DE BRAN CHE SWICO.
Recycling Information for customers in USA:
All recycling information is placed in the EIZO Nanao Technologies, Inc’s website.
Återvinnings information för kunder i Sverige:
All information om återvinning finns på Eizo Europe AB:s hemsida:
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|