1500W
CARBON FIBRE
FULL WIDTH POWER PLANER
BFPCF
INSTRUCTION MANUAL
Code: BFPCF
Date: 080529
Black
Cyan
Magenta
Yellow
Edition: 06
Op: DCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Description of symbols
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
Double insulated for additional protection.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Conforms to relevant standards
for electromagnetic compatibility.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Specifications
Voltage:
230-240V ~ 50Hz
1500W
15000 min-1
Power rating:
No load speed:
Planing depth :
Planing width:
Blades:
Environmental protection
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
0 - 2mm
180mm
Type Mn 65,
180mm (reversible),
set of 3
Insulation:
Weight:
Double Insulated
8.5kg
This planer is double insulated. There are two independent
barriers of insulation to protect you from the possibility of
electric shock.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Personal safety
General safety rules
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in
serious personal injury.
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term “power tool” in all of
the warnings listed below refers to your mains operated
(corded) power tool or battery operated (cordless)
power tool.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
Save these instructions
1. Work area
a. Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools with
your finger on the switch or plugging in power tools that
have the switch on invites accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• After long working periods, external metal parts and
accessories could be hot.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
• If possible, always use clamps or a vice to hold
your work.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
• Always switch off before you put the planer down.
• Do not force the planer: let the tool do the work at a
reasonable speed. Overloading will occur if too much
pressure is applied and the motor slows resulting in
inefficient planing and possible damage to the
planer motor.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
• Always use a dust extraction system where possible.
• Rags, cloths, cord, string and the like should never be left
around the work area.
• Remove all nails, screws and other objects from the
workpiece. You can damage the blade and the tool by
cutting into a nail or other foreign object. It can also
present a safety hazard.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in a
hazardous situation.
• Handle the blades very carefully.
• Be sure that the blade installation bolts are securely
tightened before operation.
• Always wear eye and ear protection and use a
dust mask.
• Hold the tool firmly with both hands.
• Keep hands away from rotating parts.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
• Before using the tool on an actual workpiece, switch
on and let it run for a while. Watch for vibration or
wobbling that could indicate poor installation or a poorly
balanced blade.
Additional safety rules for electric planers
• Fully unwind cable drum extensions to avoid
potential overheating.
• When an extension cable is required, you must ensure
that it has the right ampere rating for your power tool and
is in safe electrical condition.
• Make sure that a blade is not in contact with the
workpiece when you switch the machine on.
• Wait until the blades attain full speed before cutting.
• Operate the tool at least 200mm away from your face
and body.
• Always switch off and wait until the blades have
come to a complete standstill before attempting
any adjustments.
• Ensure your mains supply voltage is the same as your
tool rating plate voltage.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Never stick your finger into the chip chute. Shavings may
jam in the chute when cutting damp wood. Clean out the
chips with a stick but only when the tool has been turned
off and unplugged from the power point.
The manufacturer shall not be liable for any changes made
to the tool nor for any damage resulting from such changes.
Even when the tool is used as prescribed it is not possible
to eliminate all residual risk factors. The following hazards
may arise in connection with the tool’s construction
and design:
• Do not leave the machine running unattended. Operate
the tool only when controlled by both hands.
• Wait for the cutter to stop before setting the tool down.
An exposed cutter may engage the surface leading to
possible loss of control and serious injury.
• Damage to hearing if effective hearing protection is
not worn.
• Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the blades and adjusting the depth of cut.
• When leaving the planer, switch off and set it with the
front base up on a wooden block so that the blades are
not in contact with anything.
• Contact with the blades.
• Always change the three blades at the same time,
otherwise the resulting imbalance will cause vibration and
shorten the blade and tool life.
WARNING. Before connecting a tool to a power source
(mains socket power point receptacle, outlet, etc.) be sure
that the voltage supply is the same as that specified on the
nameplate of the tool. A power source with a voltage greater
than that specified for the tool can result in serious injury to
the user, as well as damage to the tool.
• Reaching under the base whilst the tool is running and
making contact with the blade.
• Kickback of workpiece and parts of workpiece.
• Blade fracture.
• Catapulting of faulty pieces from the blade.
Contents of carton
The GMC BFPCF Full Width Planer is supplied with the
following accessories as standard:
If in doubt, do not plug in the tool. Using a power source
with a voltage less than the nameplate rating is harmful to
the motor.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
• Set of 3 Blades (Fitted)
• Combined Parallel and Bevel Fence
• Blade Spanner
• Spare Drive Belt
• Dust Extraction Adaptor
• Spare Set of Carbon Brushes
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and frail people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
Unpacking
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your product
1. On/off trigger switch
2. Lock-off button
8. Fence attachment point (x 4)
9. Reversible blades
10. Blade barrel
15. Front handle lock lever
16. Front handle set screw
17. Drive belt cover
3. Depth adjustment knob
4. Main handle
11. Clamping screw (x 5)
12. Moveable front base
13. Fixed rear base
18. Dust extraction adaptor
19. Blade spanner
5. Front handle
6. Dust/chip extraction port
7. Fence attachment knob (x 2)
20. Spare drive belt
14. Combined parallel and
bevel fence guide
1
2
4
5
3
8
13
10
9
11
16
12
7
8
15
17
14
6
19
20
18
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. The numbers on the ring under the depth adjustment
knob indicate the depth of cut. For example when ‘2.0’ is
next to the pointer on the front of the planer, the depth of
cut is 2mm.
Assembly
The GMC BFPCF Planer is packed, fully assembled except
for the dust extraction adaptor and combined parallel and
bevel fence guide.
3. If it is necessary to plane to a precise depth, plane a
scrap piece of wood, measure the difference in thickness
and adjust the setting if necessary.
Adjusting the front handle
1. Hinge out the front handle lock lever (15) and move the
front handle to one of four positions to best suit the task
at hand.
Switching on and off
CAUTION. Before plugging
the machine into the power
point always check that the
trigger switch (1) and lock-off
button (2) work properly. Before
switching on, ensure that the
blade drum is not making
contact with any surface.
1. Plug in the machine, push
in the lock-off button (2) and
pull the trigger switch (1).
2. Hinge back lever (15) to
secure the front handle in
the selected position.
2. To stop the tool, simply
release the trigger switch (1).
Note. If necessary, the lever
action mechanism can be
adjusted using the front handle
set screw (16).
3. In order to restart the
machine, it is necessary to
operate both the lock-off
button (2) and the trigger
switch (1). This is an important safety feature that helps
prevent accidental operation of the planer.
Adjusting the
depth of cut
CAUTION. Always ensure
that the tool is switched off
and unplugged from the
power supply before making
adjustments or installing or
removing blades.
1. Rotate the depth adjustment
knob (3) clockwise for a
deeper cut and anti-clockwise
for a shallower cut.
CAUTION. Please note that the planer blades continue to
spin for some time after switching off the planer. Wait until
the motor has completely stopped before setting down the
tool to prevent damage to the planer blades or the surface.
If you wish to rest the planer on its side, do not rest it on the
side with the vents to prevent dust or chips from getting into
the motor.
4. When the planer is not to be used for a short period, set
the depth control knob to the “P” position and rest the
front of the planer on a block of wood to keep the base
clear of the surface.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Planing
Chamfering
1. Rest the front base (12) flat on the workpiece
surface without the blades making any contact with
the workpiece.
1. To make a chamfered cut as shown in fig.1, First align the
“v” groove (fig. 2) in the front base (12) of the planer with
the corner edge of the workpiece.
2. Switch on the tool and wait for the blades to reach
full speed.
2. Run the planer along the corner edge.
Fig. 1. Chamfered edge.
3. Move the tool gently forward, applying pressure on the
front of the tool, using your hand on the front handle (5)
at the start of planing and pressure at the rear of the tool,
using your hand on the main handle (4) towards the end
of the planing stroke.
Fig. 2. Aligning the “v” groove.
1
2
4. Push the planer beyond the edge of the workpiece
without tilting it downwards or upwards.
Tip. Treat the material as if it was slightly longer than it
actually is. Then you will continue with your planing action
until the blades have well passed the end of your workpeice.
5. The rate of planing and the depth of cut determine the
quality of the finish. For rough cutting, you can increase
the depth of cut, however to achieve a good finish you
will need to reduce the depth of cut and advance the tool
more slowly.
Combined parallel and bevel fence guide
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades.
Note. Planing is easier if you incline the workpiece slightly
away from you so that you plane “downhill”.
CAUTION. Moving the machine too fast may cause a poor
quality of cut and can damage the blades or the motor.
Moving the machine too slowly may burn or mar the cut.
The proper feed rate will depend on the type of material
being cut and the depth of the cut.
Practice first on a scrap piece of material to gauge the
correct feed rate and the cut dimensions.
1. Fit the fence guide (14) to the base by screwing the
knobs (7) into the fixing points (8).
CAUTION. Always use two hands to hold the planer.
CAUTION. Where possible, clamp the workpiece to
the bench.
2. Loosen the two wing nuts and set the angle of the fence
if you wish to use it as a guide for making bevel cuts.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. When set at right angles to
the planer base, the fence
provides a guide to help
control the planing action.
1. Using the supplied spanner (19), loosen the five clamping
screws (11).
Note. The fence can be fitted
to either side of the base.
Note. The angle graduations
marked on the fence are for
indicative purposes only. For
accurate bevel cutting it is necessary to measure the angle
of the fence, make a trial cut and adjust if necessary.
2. Remove the planer blade (9) from the slot in the blade
barrel (10) in which it is retained.
Shavings extraction
1. The dust/chip extraction
port (6) allows connection
to a vacuum dust extraction
system.
Installing a planer blade
1. The blades are reversible as they have a cutting edge on
both sides. If a blade edge is worn or damaged, the blade
can be removed and put back the other way around.
2. Using the dust extraction
adaptor (18) permits a
dust extraction system to
be connected to the dust
extraction port (6).
Either turn over the planer blade (9) or replace it if
required.
2. Slide the good blade face up into the blade support block
of the blade barrel (10).
Note. If only one blade is damaged, it can be replaced
without the need to replace the other two blades. When
blades are worn, they must be replaced as a set of three to
prevent unbalanced operation with consequential dangerous
vibration and possible damage to the tool.
3. To fit the adaptor (18) insert it into the port (6) and twist it
clockwise until it locks into position.
Removing and installing planer blades
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before installing or
removing blades.
Note: The ridge along the blade should be on the blade
face on the opposite side to the clamping screws (11).
Your planer is fitted with reversible blades. Blades can be
reversed when blunt. After both sides of the blades have
been used they should be discarded.
3. Tighten the clamping screws
(11), in the following manner.
Order of tightening
clamping screws
Tighten the two outside
Note: These blades cannot be re-sharpened.
clamping screws snug tight,
then the next two screws,
then the middle screw.
Removing a planer blade
CAUTION. The blades are very sharp. Take care when
handling them.
1
3
5
4
2
Working in the same order,
fully tighten all five screws.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Repeat for the two remaining blades.
CAUTION. When installing blades, first clean out all chips
or foreign matter adhering to the blade barrel (10) and the
blades themselves. Use blades of the same dimensions
and weight, or the barrel will oscillate and vibrate causing
poor planing action and possibly a machine breakdown.
Tighten the clamping screws (11) carefully when attaching
the blades to the planer. A loose clamping screw could
be extremely dangerous. Regularly check to see they are
tightened securely.
• Nicks in surface – as caused by the edge of one or all
blades not being parallel to the surface of the rear base.
(a)
(b)
CAUTION. The planer is designed so that the blades are
correctly aligned if placed flush into the barrel slots and
tightened correctly.
• Gouging at start – as caused by the edge of one or all
blades not protruding enough in relation to the surface of
the rear base.
When inserting new blades it
Blade must be
is essential that they sit square
positioned centrally
in their slot, that they are fully
inserted and that the cutting
on the drum
edges are absolutely level,
i.e. parallel to the surface of
the rear base. Only when all
(a)
(b)
these conditions are satisfied
should the clamping screws be
tightened. If the blades protrude
or are not square, they could hit the casing with serious risk
to the operator and others in the vicinity.
• Gouging at end – as caused by the edge of one or all
blades protruding too far in relation to the surface of the
rear base.
(A) front base (moveable shoe)
(B) rear base (stationary shoe)
Note. Your planing surface will end up rough and uneven
unless the blades are set and secured properly.
Drive belt replacement
The examples below show proper and improper settings:
CAUTION. Always ensure that the tool is switched off
and unplugged from the power supply before making
adjustments or installing or removing blades.
Correct setting
1. To replace the drive belt first take out the three cross-
head screws that secure the drive belt cover (17) on the
left-hand side of the planer as viewed from the rear.
(a)
(b)
Note. The front screw is longer than the other two. Take
care to replace this screw in the same hole when replacing
the cover.
• Correct setting - clean smooth cut.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the damaged belt by pulling it sideways off the
top pulley and turning the bottom pulley by hand. Use a
soft brush to clean the pulleys and the surrounding area
Cleaning
1. Keep the tool’s air vents unclogged and clean at all times.
2. Remove dust and dirt regularly. Cleaning is best done
with compressed air or a dry, soft to medium brush like a
paint brush.
Note. Wear eye protection when cleaning out the pulley area.
3. With the six continuous “v” profiles on the inside, place
the new belt over the bottom pulley. Half fit the other end
of the belt on the top pulley then roll the belt in place
whilst turning the pulley.
CAUTION. Wear protective goggles when cleaning the tool.
3. Re-lubricate all moving parts at regular intervals.
4. Never use caustic agents to clean plastic parts.
4. Check that the belt runs
evenly by manually turning
the belt.
CAUTION. Do not use cleaning agents to clean the plastic
parts of the tool. A mild detergent on a damp cloth is
recommended. Water must never come into contact with
the tool. Ensure the tool is thoroughly dry before using it.
5. Replace the cover and the
three fixing screws ensuring
that the longer screw is
located in the hole at the
front of the cover.
Power cord maintenance
If the supply cord needs replacing, the task must be
carried out by the manufacturer, the manufacturer’s agent,
or a qualified electric service repairer in order to avoid a
safety hazard.
6. Plug the machine back into the power outlet and switch
the tool on and run for a minute to make sure that the
motor and belt are operating correctly.
Maintenance
WARNING. Always ensure that the tool is switched off and
the plug is removed from the power point before making any
adjustments or maintenance procedures.
Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing or you simply need help
or advice, please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair is required, you must
provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|