User’s Manual
CVEQ 100 Series and
SVEQ 100 Series
Composite Video or S-Video and Audio Line Drivers
with Gain and Equalization
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
68-1442-01 Rev. C
07 08
+81.3.3511.7655 FAX +81.3.3511.7656
© 2008 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
警告
安全须知 • 中文
这个符号提示用户该设备用户手册中
电源 • 该设备只能使用产品上标明的电源。 设备
必须使用有地线的供电系统供电。 第三条线
（地线）是安全设施，不能不用或跳过。
拔掉电源 • 为安全地从设备拔掉电源，请拔掉所有设备后
或桌面电源的电源线，或任何接到市电系统的电源线。
电源线保护 • 妥善布线， 避免被踩踏，或重物挤压。
有重要的操作和维护说明。
这个符号警告用户该设备机壳内有暴
露的危险电压，有触电危险。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
注意
阅读说明书 • 用户使用该设备前必须阅读并理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
通风孔 • 有些设备机壳上有通风槽或孔，它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备，以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
N
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start Guide — CVEQ/SVEQ 100 Series
Installation and service must be performed by authorized
personnel only. These line drivers must be used with UL
approved, grounded electrical boxes.
C
To install and set up the line driver, follow these steps and see the
appropriate sections of this manual for details.
Step 1
Turn the input and output devices off and unplug their power cords.
Verify that the line driver is disconnected from the power source
before proceeding.
Step 2
Attach output cables to the rear panel of the line driver and to the
output devices. See "Rear Panel Features and Operation" in chapter 3
for details.
Step 3
Attach input cables from the input devices to the line driver’s front
panel input connectors. See "Front Panel Features and Operation" in
chapter 3.
Step 4
Connect power cords (see page 3-11) and turn on the output devices
(projector/monitor, speakers) and input devices.
Step 5
The picture should appear and sound should be audible. If not,
ensure that all devices are plugged in and receiving power. Check
the cabling, make adjustments as needed. For further details, see
"Testing and troubleshooting" in chapter 2.
Step 6
While watching the display, adjust the video gain and
equalization by using the rotary gain and equalization (EQ) control
potentiometers. An oscilloscope can be used to achieve a more
precise adjustment. See “Gain adjustment control" and "Equalization
(EQ) adjustment control” in chapter 3 for details.
Make all adjustments using an Extron Tweeker or small screwdriver.
If using very short output cables, set all potentiometers to the default
setting (the arrow on the control pointing to the dot beside it).
CVEQ 100 Series
SVEQ 100 Series
CVEQ 100 and SVEQ 100 Series • Quick Start Guide
QS-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start — CVEQ/SVEQ 100 Series, cont’d
Table of Contents
Features ........................................................................................ 1-2
When using long cables, follow these steps:
a. Supply the color bars test signal to the input. (Recommendation:
use an Extron VTG 300 Video Test Generator to generate the test
signal.)
b. Adjust the Gain control(s) for the output until the signal level
at the far end is the same as the input (or the display shows the
correct brightness and contrast).
c. Adjust the EQ control for the output so that no overshoot or
round front corner appears at the far end on the oscilloscope or
you see a sharp picture with no smearing.
Step 7
See "Installation Instructions" in chapter 2 for further installation
details.
Accessories ........................................................................................A-1
CVEQ 100 and SVEQ 100 Series • Quick Start Guide
CVEQ 100 and SVEQ 100 Series • Table of Contents
QS-2
TOC-i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont’d
CVEQ 100 and SVEQ 100 Series
All trademarks mentioned in this manual are the properties of their respective owners.
68-1442-01 Rev. C
07 08
Chapter One
1
Introduction
About this Manual
Features
CVEQ 100 and SVEQ 100 Series • Table of Contents
TOC-ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About this Manual
CVEQ 100 and SVEQ 100 Series
This manual contains information about the Extron composite
video CVEQ 100 Series, and the S-video SVEQ 100 Series of high
performance 1-input, 1-output video line drivers. Both series
of line drivers support stereo or dual mono audio (balanced or
unbalanced). These line drivers can drive video signals up to
1000 feet using Extron MHR cable.
The composite video CVEQ 100 Series is comprised of the rack
or furniture-mounted VersaTools® CVEQ 100, the wall-mounted
CVEQ 100 D featuring Decora® wall plates and faceplates, the
architectural adapter plate CVEQ 100 AAP, and the triple space
mini architectural adapter plate CVEQ 100 MAAP.
The S-video SVEQ 100 Series is comprised of the rack or
furniture-mounted VersaTools® SVEQ 100, the wall-mounted
SVEQ 100 D featuring Decora® wall plates and faceplates, the
architectural adapter plate SVEQ 100 AAP, and the triple space
mini architectural adapter plate SVEQ 100 MAAP.
Features
Chapter Two
Long distance line driving — Drives composite video or
S-video signals up to 1000 feet (300 meters) using Extron's
MHR cable.
2
Balanced or unbalanced stereo or dual mono output —
Unbalanced stereo audio input can be output as balanced
or unbalanced stereo audio or as dual mono.
Gain adjustment — All models offer a video gain adjustment
for composite video and Y of S-video with a range of
-1 dB to +3 dB, and C of S-video with a range of 0 dB to
+10 dB.
Installation
Application Examples
Installation Instructions
Equalization adjustment — Each model features an
equalization adjustment range of 0 dB to +7 dB at 5 MHz
that changes the level and peaking of the output signal to
compensate for use of long cables.
Stereo or dual mono output selector switch — A rear panel
switch selects between stereo and dual mono output
formats (D, AAP, and MAAP models only).
Front panel LED indicator — Indicates when the line driver is
receiving power (all models) or a video signal (D, AAP,
and MAAP models only).
CVEQ 100 and SVEQ 100 Series • Introduction
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Extron
Application Examples
SI 26X
Two-way Ceiling
Speakers
To get started, refer to the "Quick Start Guide" at the beginning
of this manual.
Audio
Installation and service must be performed by
authorized personnel only.
C
A
122
S
MP
OUTPUT
S
S-video
R
L
4/8 Ohms SPEAKE
US
C
S
REMOT
10V
INPUT
VOL/MUTE
R
L
L
POWER
Extron
Extron
MPA 122
Mini Power
Ampliꢀer
R
SI 26
.
12V
3A MAX
Surface-mount
Speakers
Audio
Projector
OUTPUT
R
Y
T
L
INPU
Y
C
R
C
12V
0.2A MA
Extron
TREBLE
MPA 122
2
BASS
A
12
Extron
MP LIFIER
L
Mini Power
LEVE
O
STERE
MINI POWER AMP
SVEQ 100
Ampliꢀer
ON
DUAL
O
MON
TER
LIMI
F
OF
S-Video Line Driver
Extron
N
I
SVEQ 100 MAAP
O
E
D
D
I
V
S-video Line Driver
N
I
O
I
U
A
P
A
R
A
M
0
0
1
L
Q
E
V
S
1,000’
CPM101
DVD
DVD
Projector
SVEQ 100 application example
SVEQ 100 MAAP application example
Extron
Extron
SI 26X
SI 26X
Two-way Ceiling
Speakers
Tw o-way Ceiling
Speakers
Audio
Extron
MPA 122
Mini Power
Ampliꢀer
L
2
S
A
12
MP
OUTPU
EAKERS
A
122
MP
T
R
OUTPUTS
R
L
4/8 Ohms SP
L
4/8 Ohms SPEAKRS
US
US
C
E
REMO
V
C
INPUTS
S
REMOT
10V
E
INPUT
10 MUT
VOL/
L
L
VOL/MUTE
R
R
L
L
POWE
R
POWER
Projector
V
Extron
MPA 122
Mini Power
Ampliꢀer
12
R
3A MAX.
.
12V
Audio
3A MAX
Audio
Composite
Video
Projector
Composite
Video
AUDIN
L
Extron
CVEQ 100 AAP
R
N
I
O
I
Composite Line Driver
D
U
A
O
VIDEO IN
P
VIDE
A
A
N
I
R
0
0
1
Q
E
V
L
S
Extron
VCR
CVEQ 100 D
Composite Line Driver
VCR
CVEQ 100 D application example
CVEQ 100 AAP application example
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-2
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Rack mounting
Installation Instructions
For rack mounting, do not install the rubber feet. Mount
The following sections explain the installation of the CVEQ 100
the distribution amplifier on a 19" wide 1U VersaTools® rack
shelf (Extron RSF 123, part #60-190-20; Extron RSB 123, part
#60-604-21), a standard 1U Universal or Basic rack shelf (Extron
RSU 129, part #60-190-01; Extron RSB 129, part #60-604-02), or a
Universal or Basic 1U 6-inch deep rack shelf (Extron RSU 126,
part #60-190-10; Extron RSB 126, part #60-604-11).
and SVEQ 100 series of line drivers.
Installing the CVEQ 100/SVEQ 100
Mounting the CVEQ 100 and SVEQ 100
The CVEQ 100 composite video line driver and the SVEQ 100
S-video line driver can be set on a table, mounted on a rack
shelf, mounted under a desk or table, mounted through
furniture (CVEQ 100 only), or mounted on the back of a rack
(SVEQ 100 only).
1.
If feet were previously installed on the bottom of the line
driver, remove them.
2.
Mount the line driver on the rack shelf, using two
4-40 x 3/16" screws in opposite (diagonal) corners to
secure the unit to the shelf.
Tabletop use
Four self-adhesive rubber feet are included with the line driver.
3.
Install blank panel(s) or other unit(s) on the rack shelf.
For tabletop use, attach one foot at each corner of the bottom
side of the unit and place the unit in the desired location. See
chapter 3 for details on wiring and switch settings.
VersaTools Rack Shelf
UL rack mounting guidelines
The following Underwriters Laboratories (UL) guidelines
pertain to the safe installation of the line drivers in a rack.
1.
Elevated operating ambient temperature — If installed in a
closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than
room ambient temperature. Therefore, install the line
driver in an environment compatible with the maximum
ambient temperature (Tma = +122 °F, +50 °C) specified by
Extron.
1/4 Rack Width Front
False Faceplate
2.
3.
4.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
Mechanical loading — Mount the equipment in the rack so
that a hazardous condition is not achieved due to uneven
mechanical loading.
Mounting the line driver on a VersaTools rack shelf
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g. use of power strips).
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-4
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Furniture mounting — under-desk
1U Universal Rack Shelf
To mount the line driver under furniture, use the optional
VersaTools under-desk mounting kit for the SVEQ 100
(Extron MBU 123, part #70-212-01) or the optional under-desk
kit for the CVEQ 100 (Extron MBU 125, part #70-077-01).
1/2 Rack Width Front False
Faceplate
1/4 Rack Width Front False
Faceplate
Both front false faceplates
use 2 screws.
Under-desk mounting kit
part # 70-077-01
Under-desk mounting kit
part # 70-212-01
(2) 4-40 x 3/16"
Screws
Use 2 mounting holes on
opposite corners.
Preparing the line driver for under-desk mounting
1.
2.
3.
If rubber feet were previously attached to the bottom of the
unit, remove them.
Mounting the line driver on a standard rack shelf
Attach the mounting brackets to the line driver with the
provided machine screws as shown in the previous figure.
6" Deep Rack Shelf
1/2 Rack Width Front False
Faceplate
Hold the unit with the attached brackets against the
underside of the table or other furniture. On the mounting
surface, mark the location of the bracket’s screw holes.
4.
5.
Drill ³⁄ " (2 mm) diameter pilot holes, ¼" (6.3 mm) deep in
³²
the mounting surface at the marked screw locations.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than ¼" of the screw head protrudes.
Front false
faceplate
uses 2
6.
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
screws.
7.
8.
Slide the unit slightly forward or back, then tighten all four
screws to secure it in place.
Attach input and output cables. See chapter 3.
(2) 4-40 x 3/16"
Screws
Furniture mounting — through-desk
(CVEQ 100 only)
Use 2 mounting holes on
opposite corners.
To mount the CVEQ 100 through furniture, use the optional
VersaTools through-desk mounting kit (Extron MBD 129,
part #70-077-02), as follows.
Mounting the line driver on a 6-inch rack shelf
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-6
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
9.
Attach input and output cables. See chapter 3.
Back of the rack mounting (SVEQ 100 only)
The SVEQ 100 can be mounted to the rear of a rack using the
Extron VersaTools MBB 100 back of the rack mounting kit
(part #70-367-01). The kit allows the product to be vertically
mounted to the front or rear rack supports and facing either
towards the front or the rear of the rack.
Preparing the CVEQ 100 for through-desk mounting
1.
2.
3.
If rubber feet were previously attached to the bottom of
the unit, remove them.
Attach the mounting brackets to the CVEQ 100 with the
provided machine screws as shown in the previous figure.
Hold the unit with the attached brackets against the
underside of the table or other furniture. On the
mounting surface, mark the location of the bracket’s screw
holes.
Using the MBB 100 back of the rack kit
1.
2.
3.
If necessary, remove the feet from the bottom of the
line driver.
4.
Mark the opening on the desk using a soft pencil. The
opening should be slightly larger than the dimensions of
the unit.
Use an appropriate saw to cut the opening. If needed,
enlarge the hole with a file or sandpaper.
Remove two screws from one side of the unit. Retain the
screws for possible later reassembly without the bracket.
Attach one bracket to the side of the unit using the longer
screws included in the kit.
5.
6.
Drill ³⁄ " (2 mm) diameter pilot holes, ¼" (6.3 mm) deep in
³²
4.
5.
Repeat steps 2 and 3 on the other side of the unit.
the mounting surface at the marked screw locations.
Mount the unit to the rack using the two included rack
screws (see the following illustration). The SVEQ 100 can
be vertically mounted facing in either direction. See the
following diagram.
Insert #8 wood screws into the four pilot holes. Tighten
each screw into the mounting surface until slightly less
than ¼" of the screw head protrudes.
7.
8.
Align the mounting screws with the slots in the brackets
and place the unit against the surface, with the screws
through the bracket slots.
7.
Attach input and output cables. See chapter 3 for details
on wiring.
Slide the unit slightly forward or back, then tighten all
four screws to secure it in place.
Only VersaTools products and most IP Link products can
be mounted using the back of the rack mounting kit.
N
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-8
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Installing the CVEQ 100 AAP/SVEQ 100 AAP
The CVEQ 100 AAP and SVEQ 100 AAP are double space high
architectural adapter plate products that mount in a wall or
furniture using an optional mounting frame.
1.
Remove power from the line driver by disconnecting the
power supply.
2.
3.
Attach the mounting frame to wall box.
Route output cables through the wall box and frame and
connect them to the line driver.
4.
Mount the line driver to the mounting frame with machine
screws, as shown in the following illustration. Take care
not to damage the output cable(s), which fit through the
mounting frame and into the wall box.
Inside
Outside
Cable
Clamp
AAP 102
Connector
SVEQ 100 back of the rack installation example
AAP 102
N
UDIO
I
A
P
R
VIDEO
IN
L
CVEQ 100 AA
#4-40 Nut w/ Captive
Washer
Extron
CVEQ 100 AAP
Composite Line Driver
Mounting the line driver to a wall box
5.
Reconnect the power supply, cable all products (see
chapter 3), and restore power to the equipment.
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-10
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Mounting in a European cable channel
Installing the CVEQ 100 MAAP/SVEQ 100 MAAP
1.
Remove power from the line driver by disconnecting the
power supply.
The CVEQ 100 MAAP and SVEQ 100 MAAP are three space
high mini architectural adapter plate products that mount in a
wall or furniture using an optional mounting frame or European
cable channel system.
2.
3.
Attach the MAAP adapter plate to the junction box.
Place the cover frame between the adapter plate and the
line driver, route the output cables through the frame, and
connect them to the line driver.
Mounting in an external wall box
1.
Remove power from the line driver by disconnecting the
power supply.
4.
Fasten the line driver to the adapter plate, as shown below.
2.
3.
Attach the mounting frame to the wall box.
Route output cables through the wall box and frame, and
connect them to the line driver.
Euro Channel
(not included)
4.
Mount the line driver to the mounting frame with machine
screws, as shown in the following illustration. Take care
not to damage the output cable(s), which fit through the
mounting frame and into the wall box.
O
VIDE
IN
DIO IN
U
A
R
CVEQ 100 EU
L
Extron
MAAP 101EUC
Mounting Frame
Extron
MAAP 101EU
Mounting Frame
Extron
CVEQ 100 MAAP
Composite Line Driver
Mounting Screws
Legrand External
Wall Box
O
Mounting the line driver in a Euro channel
VIDE
IN
UDIO IN
A
R
CVEQ 100 EU
L
5.
Reconnect the power supply, cable all equipment (see
chapter 3), and restore power to the equipment.
Extron
CVEQ 100 MAAP
Mounting the line driver in a wall box
5.
Reconnect the power supply, cable all equipment (see
chapter 3), and restore power to the equipment.
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-12
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Wall Stud
Wall Stud
Installing the CVEQ 100 D/SVEQ 100 D
The CVEQ 100 D and SVEQ 100 D are wall-mounted products
and can be mounted into an electrical wall box. This section
includes site preparation, wall box installation, and the
mounting of the line driver in the wall box.
e
Installation Cable
Cable Clamp
lamp
The line driver must be installed into an Underwriters
Laboratories (UL) approved electrical wall box. The
box is not included with the line driver; the installer is
responsible for obtaining and installing the box.
N
Nails
Screws or Nails
Preparing the site and installing the wall box
Choose a location that allows cable runs without interference.
Allow enough depth for both the wall box and the cables. You
may need to install the cables into the wall or conduits before
installing the line driver.
Attaching the wall box to a wall stud
The line driver can be installed in a standard one-gang electrical
wall box. The installation must conform to national and local
electrical codes. A dimensional drawing and a cutout template
of the line driver are provided in appendix B of this manual.
If attaching the wall box to wood, use four #8 or #10 screws
or 10-penny nails. A minimum of ½" (1.3 cm) of screw
threads must penetrate the wood.
If attaching the wall box to metal studs, use four #8 or
#10 self-tapping sheet metal screws or machine bolts with
matching nuts.
The cutout template shown in appendix B is not full size.
Pay attention to the measurements shown on the template.
N
1.
Mark the guidelines for the opening on the wall.
Mounting the line driver
•
If the line driver will be installed in a wall box, place
the box against the installation surface and draw a line
on it around the outside of the box.
Before mounting the line driver and if has not already been
tested, test the system to make sure that the connections and
settings are correct. See "Testing and troubleshooting" in this
chapter.
•
If the line driver will be installed without a wall box
(fastening it directly to the wall), measure and mark
the surface for the cutout area indicated in the cutout
template.
If the system is operating correctly, the line driver can be
installed in the wall. Adjust the gain and equalization, and set
the Audio Out switch to Stereo or Dual Mono before fastening
the line driver into the wall box. The controls and cables will
be inaccessible after installation. See “Rear Panel Features
and Operation" in chapter 3 for details about settings and
adjustments.
2.
3.
Cut out the material from the marked area.
Check the opening size by inserting the wall box (if used)
or the line driver (if no box is used) into the opening. The
box and line driver should fit easily into the opening.
Enlarge or smooth the edges of the opening if needed.
Continue mounting the line driver by following the steps below.
4.
5.
Feed cables through the wall box punch-out holes, and
secure them with cable clamps to provide strain relief.
1.
Remove power from the line driver by disconnecting the
power supply from the AC source.
Insert the wall box into the opening, and attach it to the
wall or stud using nails or screws. The front edge should
be flush with the outer wall surface. See the following
illustration.
2.
3.
Connect the output cables to the rear of the device.
Place the line driver through the opening in the wall and
into the wall box. Take care not to damage the output
cable(s), which fit behind the line driver at the back of the
wall box.
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-14
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
3.
4.
Check the video source’s user’s guide or contact Extron to
determine if there are special requirements to output video
to the external video port.
4.
Mount the line driver to the wall box with machine screws
as shown in the following illustration.
Call the Extron S3 Sales and Technical Support Hotline if
the image still does not appear or there is no sound.
If the image is not displayed correctly
1.
If the picture is too bright or too dark, or if the edges of the
image seem to exceed their boundaries, or if thin lines and
sharp edges look thick and fuzzy, change the gain setting.
Wall Box
If the picture appears and is stable, but it has ghosting
or blooming, verify that the video input is properly
terminated. If the problem is not resolved by changing the
termination, try using a different input cable. Poor quality
or damaged cable can cause ghosting and blooming.
Extron
CVEQ 100 D
AUDIO IN
L
R
Wall opening
is flush with
edge of box.
IN
O
E
ID
V
2.
If the picture still is not displayed correctly, call the Extron
S3 Sales and Technical Support Hotline.
Decora
Wall Plate
Mounting the line driver to a wall box
5.
6.
Attach the Decora® wall plate to the line driver as shown in
the illustration above.
Reconnect the power supply, connect input cables to the
line driver, and restore power to the equipment.
Testing and troubleshooting
1.
Apply power to the line driver. The power/signal LED on
the line driver lights amber (power) or green (video input).
2.
If the LED does not light, check the wiring at both the line
driver and the power supply, and make sure the power
supply is connected to a power source.
If the image does not appear or there is no sound
1.
2.
Make sure that all the devices are powered on.
Ensure that the connectors are wired correctly at both
ends of the cables. Audio cables must be wired for an
unbalanced stereo input signal and for the appropriate
(unbalanced or balanced) output signal.
CVEQ 100 and SVEQ 100 Series • Installation
CVEQ 100 and SVEQ 100 Series • Installation
2-16
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
CVEQ 100 and SVEQ 100 Series
Chapter Three
3
Operation
Front Panel Features and Operation
Rear Panel Features and Operation
Replacing the Decora Faceplate
(CVEQ 100 D and SVEQ 100 D)
CVEQ 100 and SVEQ 100 Series • Installation
2-18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Front Panel Features and Operation
VIDEO IN
AUDIO IN
1
4
GAIN
EQ
CVEQ 100
VIDEO LINE DRIVER
CVEQ 100
Front Panel
L
R
1
2a
3
CVEQ 100 MAAP
CVEQ 100 MAAP
Front Panel
6
C
GAIN
Y
GAIN
EQ
S-VIDEO IN
AUDIO IN
1
5
SVEQ 100
S-VIDEO LINE DRIVER
SVEQ 100
Front Panel
1
2a
3
2b
L
R
SVEQ 100 MAAP
VIDEO
IN
AUDIO IN
SVEQ 100 MAAP
Front Panel
6
L
R
CVEQ 100 AAP
CVEQ 100 AAP
Front Panel
1
4
6
Faceplate
AUDIO IN
AUDIO IN
1
5
1
4
L
L
6
6
S-VIDEO
IN
AUDIO IN
R
R
S-VIDEO
IN
VIDEO IN
L
R
SVEQ 100 AAP
Wall Plate
SVEQ 100 AAP
Front Panel
1
5
6
SVEQ 100 D
Front Panel
CVEQ 100 D
Front Panel
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-2
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Power indicator LED — This LED lights:
Audio input connectors — Connect an unbalanced stereo audio
source to these left (L) and right (R) RCA connectors. Wire the
male connector as shown in the following illustration.
a
f
• Amber when the line driver is receiving full power (this
applies to all models except the CVEQ 100 and SVEQ 100,
which light green instead).
• Green when the line driver is receiving a video signal (this
only applies to the D, AAP, and MAAP models).
Tip (+)
Gain potentiometer (CVEQ 100 and luma of SVEQ 100) — Use
a small screwdriver to rotate this potentiometer to adjust the
CVEQ 100's gain and the SVEQ 100's luminance gain when the
line driver is connected to long output cables. The adjustment
range is -1 dB to +3 dB. The default is unity (the dot position).
See "Gain adjustment control" in this chapter.
Ç
Sleeve (
)
Gain potentiometer (chroma of SVEQ 100) — Use a small
screwdriver to rotate this potentiometer to adjust the chroma
gain when the SVEQ 100 is connected to long output cables. The
adjustment range is 0 dB to +10 dB. The default is unity (the dot
position). See "Gain adjustment control" in this chapter.
É
c
Equalization (EQ) potentiometer — Use a small screwdriver
to rotate this potentiometer to adjust equalization when the line
driver is connected to long output cables. The adjustment range
is 0 dB to +7 dB. The default is set to 0 dB (the dot position). See
"Equalization (EQ) adjustment control" in this chapter.
Video input connector — Connect a composite video input
source to this RCA connector.
d
e
S-video input connector — Connect an S-video input source to
this 4-pin mini DIN connector. See the following pinout table.
3
4
1
2
S-video Pinout Table
NAME DESCRIPTION
PIN
1
GND
GND
Y
Ground (Y)
Ground (C)
Luminance
Chrominance
2
3
4
C
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-4
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Rear Panel Features and Operation
1
5
OUTPUT
INPUT
12V
0.2A MAX
L
R
L
R
VIDEO
VIDEO
2a
3
4a
5
1
4b
CVEQ 100 Rear Panel
SVEQ 100 AAP Rear Connectors
INPUT
Y
OUTPUT
Y
C
L
CVEQ 100 AAP Audio
Output Wiring
To compensate for image degradation
due to long cable runs, adjust the gain
and equalization (EQ) potentiometers.
(Top-Down View)
UNBALANCED
BALANCED
-
Faint, dim, or "soft" images can be
corrected by rotating the gain
12V
0.2A MAX
potentiometer for maximum brightness.
To adjust the output level and peaking
sharper image, rotate the EQ
-
L
R
L
R
L
R
for
a
-
-
-
-
+
+
+
+
potentiometer.
C
R
Extron Electronics
Anaheim, CA
33-1666-01
A
05 08
N15779
Y
DUAL
MONO
STEREO
EQ
GAIN
POWER
12 V
AUDIO OUTPUT
0.2
A
MAX
R
L
6
7
9
2b
SVEQ 100 Rear Panel
3
4b
5
1
CVEQ 100 AAP Rear Controls
SVEQ 100 AAP Audio
1
5
Output Wiring
To compensate for image degradation
due to long cable runs, adjust the gain
and equalization (EQ) potentiometers.
(Top-Down View)
UNBALANCED
BALANCED
-
Faint, dim, or "soft" images can be
corrected by rotating the gain
potentiometer for maximum brightness.
To adjust the output level and peaking
-
L
R
L
R
for
a
sharper image, rotate the EQ
-
-
-
-
+
+
+
+
potentiometer.
Extron Electronics
Anaheim, CA
33-1667-01
A
05 08
N15779
Y
C
GAIN
DUAL
MONO
STEREO
EQ
GAIN
POWER
12 V
AUDIO OUTPUT
0.2
A
MAX
R
L
8
9
6
7
4a
CVEQ 100 AAP Rear Connectors
SVEQ 100 AAP Bottom Controls
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-6
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
9
9
1
6
7
5
POW ER
12V
0.2A MAX
4a
1
6
7
5
CVEQ 100 D Rear Panel
CVEQ 100 MAAP Rear Panel
4a
9
9
1
6
7
5
POW ER
12V
0.2A MAX
8
8
1
6
7
5
4b
SVEQ 100 MAAP Rear Panel
SVEQ 100 D Rear Panel
Power connector — Connect the external 12 VDC power supply
into this 2-pin, 3.5 mm direct insertion connector. The power
supply is included with the unit. The "Power supply wiring"
section in this chapter explains how to wire the connector.
a
Video input connector — Connect a composite video input
source to this BNC connector.
S-video input connectors — Connect an S-video input source to
these BNC connectors.
Audio input connectors — Connect an unbalanced stereo audio
source to these left (L) and right (R) RCA connectors. Wire the
male connector as shown in the following illustration.
Ç
É
c
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-8
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
Tip (+)
Output equalization (EQ) potentiometer — Use an Extron
Tweeker (a small screwdriver) to rotate this control to adjust
equalization when the line driver is connected to long output
cables. The adjustment range is 0 dB to +7 dB. The default is
set to 0 dB (the dot position). See "Equalization (EQ) adjustment
control" in this chapter.
f
g
Sleeve (
)
Video output connector — Connect a composite video output
device to this female BNC connector.
Ü
á
Output gain potentiometer (luma) — Use an Extron Tweeker
(a small screwdriver) to rotate this control to adjust the CVEQ's
gain or the SVEQ's luminance gain when the line driver is
connected to long output cables. The adjustment range is
-1 dB to +3 dB. The default is unity (the dot position). See
"Gain adjustment control" in this chapter.
S-video Y connector (luma, white cable) — Connect the luma of
an S-video output device to this female BNC connector.
S-video C connector (chroma, yellow cable) — Connect
the chroma of an S-video output device to this female BNC
connector.
Output gain potentiometer (chroma) — Use an Extron Tweeker
(a small screwdriver) to rotate this control to adjust the SVEQ's
chrominance gain when the line driver is connected to long
output cables. The adjustment range is 0 dB to +10 dB. The
default is unity (the dot position). See "Gain adjustment control"
in this chapter.
h
i
Audio output connector — Wire a balanced/unbalanced audio
output device to this 3.5 mm, 5-pole, direct insertion captive
screw connector. See the following wiring diagrams.
e
Balanced audio is more resistant to noise and can be driven
for longer distances than unbalanced audio. For best
results, wire the output for balanced audio.
N
Audio output select switch — Use this switch to select either
stereo (up) or dual mono (down) output. When set for dual
mono, the left and right channels output the same signal (either
channel or both channels can be used). The audio output can
be wired for balanced/unbalanced mono or stereo output. The
wiring and the switch setting must match.
Balanced Stereo
Unbalanced Stereo
Left Tip (+)
Left Ring (-)
Sleeve (s)
Left Tip (+)
Sleeve
Right Tip (+)
Right Ring (-)
Right Tip (+)
Set Audio Out switch to Stereo.
Set Audio Out switch to Stereo.
Power supply wiring
Wire the line driver's power connector as shown below.
Balanced Mono
Unbalanced Mono
The CVEQ 100 and SVEQ 100 use a pre-wired captive
screw power connector. The D, AAP, and MAAP models
use direct insertion connectors.
N
Use either the left or the right channel.
Use either the left or the right channel.
Tip (+)
Ring (-)
Sleeve
Tip (+)
Sleeve
Set Audio Out switch to Dual Mono.
Set Audio Out switch to Dual Mono.
Smooth
Ridges
3
A
A
5
CAUTION Connect the sleeve to ground
(Gnd). Connecting the sleeve to
a negative (–) terminal will
SECTION A–A
damage the audio output
Do not tin the wires!
Power Supply
Output Cord
Captive Screw
Connector
Power connector wiring
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-10
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation, cont’d
Power supply voltage polarity is critical. Incorrect
voltage polarity can damage the power supply and the
line driver. Identify the power cord negative lead by
the ridges on the side of the cord.
C
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
CVEQ 100 Series
SVEQ 100 Series
Use a small, flat-blade screwdriver to rotate this control. View
the display and select the setting that gives the sharpest picture.
For a more precise setting, you can use an oscilloscope or a
waveform monitor connected to the far end of the output
cable, and adjust the equalization so that the color burst ranges
between -20 IRE and +20 IRE.
The two power cord wires must be kept separate while
the power supply is plugged in. Remove power before
wiring.
W
Do not tin the power supply leads before installing in the
direct insertion connector. Tinned wires are not as secure
in the connectors and could be pulled out.
N
The EQ control is a potentiometer with a mechanical stop
at the high and the low end. After you have reached the
high or low end of the adjustment, no change is apparent
on the display. The default is set to 0 dB (the dot position).
N
Gain adjustment control
The gain control adjusts picture brightness by compensating
for signal amplitude loss caused by cable resistance. To adjust
the output gain, view the display while using a small, flat-blade
screwdriver to rotate the potentiometer. This control produces a
gain adjustment ranging from -1 dB to + 3 dB (CVEQ and luma
of SVEQ) and from 0 dB to +10 dB (chroma of SVEQ). Select the
setting that gives the best picture brightness.
Replacing the Decora Faceplate (CVEQ 100 D
and SVEQ 100 D)
The front faceplate is replaced by removing the two rear panel
mounting screws, replacing the faceplate, then reattaching the
two screws, as shown in the CVEQ 100 D example below.
The faceplate for the SVEQ 100 D is replaced in similar
fashion.
N
CVEQ 100 Series
SVEQ 100 Series
The gain control is a potentiometer with a mechanical stop
at the high and the low end. After you have reached the
high or low end of the adjustment, no change is apparent
on the display. The default is unity (the dot position)
N
You can judge the adjustment visually by viewing the display.
For a more precise setting use an oscilloscope or a waveform
monitor connected to the far end of the output cable, and adjust
the gain so that the level at the waveform monitor is 100 IRE.
Mounting
Rear Panel
Screws
Equalization (EQ) adjustment control
Faceplate (rear)
The equalization control adjusts the output level and peaking
to get a sharp picture. This adjustment changes the level and
peaking of the output signal to compensate for capacitance
caused by up to 1000 feet (300 meters) of Extron MHR cable.
Removing the CVEQ 100 D faceplate
This control produces an equalization adjustment ranging from
0 dB to + 7 dB (CVEQ and luma of SVEQ).
CVEQ 100 and SVEQ 100 Series • Operation
CVEQ 100 and SVEQ 100 Series • Operation
3-12
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, and Accessories
Connectors
CVEQ 100 ........................... 1 female BNC
CVEQ 100 D, CVEQ 100 AAP, CVEQ 100 MAAP
1 female BNC attached via 4" pigtail
Specifications
Video
Gain................................................. Composite video and Y of S-video: -1 dB
to +3 dB (x0.9 to x1.4), adjustable
SVEQ 100............................ 2 female BNC
C of S-video: 0 dB to +10 dB (x1 to x3),
adjustable
SVEQ 100 D, SVEQ 100 AAP, SVEQ 100 MAAP
2 female BNC attached via 4" pigtails
Equalization................................... 0 dB to +7 dB (x1 to x2) at 5 MHz,
adjustable
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite
video (including sync)
0.3 Vp-p for C of S-video
Bandwidth (Y of S-video)............. 185 MHz (-3 dB)
Minimum/maximum levels........ 0.4 to 2.0 Vp-p (follows input)
Impedance...................................... 75 ohms
Output cable driving distance..... Up to 1000' (300 m) with Extron MHR
cable
Return loss...................................... -30 dB @ 5 MHz
DC offset......................................... ±5 mV with no input signal
Floating: +0.1 to -0.6 V, depending on
input signal content
Video input
Number/signal type
CVEQ 100 Series................ 1 composite video
SVEQ 100 Series................. 1 S-video
Connectors
Sync
Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
CVEQ 100 ........................... 1 female BNC
CVEQ 100 D, CVEQ 100 AAP, CVEQ 100 MAAP
1 female RCA
SVEQ 100............................ 2 female BNC
Audio
Gain................................................. Unbalanced output: 0 dB; balanced output:
+6 dB
SVEQ 100 D, SVEQ 100 AAP, SVEQ 100 MAAP
1 female 4-pin mini DIN
Frequency response ...................... 20 Hz to 20 kHz, ±0.5 dB
Nominal level ................................ 1 Vp-p for Y of S-video, and for composite
video (including sync)
THD + Noise.................................. 0.015% @ 1 kHz at nominal level
S/N.................................................. >100 dB at maximum output (unweighted)
Stereo channel separation ............ >80 dB @ 1 kHz
0.3 Vp-p for C of S-video
Minimum/maximum levels
CVEQ 100 Series................ 0.4 to 2.0 Vp-p with no offset at unity gain
Output cable driving distance..... Up to 1000' (300 m) with Extron SHR cable
SVEQ 100 Series................. For Y: 0.4 to 2.0 Vp-p with no offset at
unity gain
Impedance...................................... 75 ohms
Return loss...................................... <-25 dB @ 0 to 5 MHz
DC offset (max. allowable)........... 4.0 V
Audio input
Number/signal type..................... 1 stereo unbalanced
Connectors ..................................... 2 RCA female
Input coupling............................... AC
Impedance...................................... 20k ohms unbalanced, DC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level.............................. +8 dBu (2.5 V), unbalanced at 1% THD+N
Video output
Number/signal type
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu
N
CVEQ 100 Series................ 1 composite video
SVEQ 100 Series................. 1 S-video
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
A-2
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Enclosure type
CVEQ 100, SVEQ 100........ Metal
Audio output
Number/signal type
CVEQ 100 D, SVEQ 100 D . Metal rear enclosure, plastic faceplate
CVEQ 100, SVEQ 100........ 1 stereo, balanced/unbalanced
CVEQ 100 AAP, SVEQ 100 AAP
Metal faceplate, open at rear
All other models................ 1 stereo or dual mono (switch-selectable),
balanced/unbalanced
CVEQ 100 MAAP, SVEQ 100 MAAP
Metal faceplate, metal rear enclosure
Enclosure dimensions
Connectors ..................................... (1) 3.5 mm captive screw connector, 5 pole
Impedance...................................... 50 ohms unbalanced, 100 ohms balanced
Nominal level ................................ -10 dBV (316 mVrms), unbalanced; -2 dBu
(632 mV), balanced output
CVEQ 100 ........................... 1.0" H x 4.3" W x 3.0" D (<1U high, quarter
rack wide)
(2.5 cm H x 11.0 cm W x 7.6 cm D)
(Depth excludes connectors. )
SVEQ 100............................ 1.7" H x 4.3" W x 3.0" D (1U high, quarter
rack wide)
Maximum level.............................. +9 dBV (2.8 V) unbalanced, +17 dBu (5.6
V) balanced at 1% THD+N with a 10k ohm
load
(4.3 cm H x 11.0 cm W x 7.6 cm D)
(Depth excludes connectors. )
General
External power supply................. 100 VAC to 240 VAC, 50/60 Hz, external;
to 12 VDC, 2 A, regulated
Power input requirements........... 12 VDC, 0.2 A
Temperature/humidity................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
CVEQ 100 D, SVEQ 100 D
Faceplate..................... 2.6" H x 1.3" W x 0.1" D
(6.6 cm H* x 3.3 cm W x 0.3 cm D)
(Fits the opening in a 1 gang Decora
faceplate. *Height is 3.8" [9.5 cm],
including mounting tabs.)
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
(Depth excludes connectors. )
Cooling ........................................... Convection, no vents
Mounting
Device ......................... 2.7" H x 1.8" W x 0.75" D
(6.9 cm H x 4.6 cm W x 1.9 cm D)
(Depth excludes connectors; height
excludes mounting tabs.)
Rack mount
CVEQ 100, SVEQ 100 Yes, with optional 1U, 9.5" deep rack shelf
(RSU 129 or 60-190-03;
CVEQ 100 AAP, SVEQ 100 AAP
RSB 129, 60-604-01); or 1U, 6" deep rack
shelf (RSU 126, #60-190-10;
Faceplate..................... 1.4" H x 3.5" W x 0.1" D
(3.6 cm H x 7.1 cm W x 0.3 cm D)
RSB 126, 60-604-10); or VersaTools® 3.5"
deep rack shelf (RSF 123, #60-190-20;
RSB 129, 60-604-20).
(double space high AAP plate)
Device ......................... 1.1" H x 2.8 " W x 1.2" D
(2.8 cm H x 7.0 cm W x 3.0 cm D)
(Depth excludes connectors.)
All other models........ No, but wall or furniture mountable
Furniture mount
CVEQ 100 MAAP, SVEQ 100 MAAP
CVEQ 100, SVEQ 100 Yes, with optional mounting kits
CVEQ 100 D, SVEQ 100 D
Yes, directly, or with a standard electrical
wall box or mud ring
All other models........ Yes, with optional AAP or MAAP
mounting faceplates
Faceplate..................... 2.1" H x 2.2" W x -.1" D
(5.3 cm H x 5.7 cm W x 0.3 cm D)
(three space MAAP plate)
Device ......................... 2.0" H x 1.4" W x 1.2: D
(5 cm H x 3.6 cm W x 3.0 cm D)
(Depth excludes connectors.)
Product weight
CVEQ 100, SVEQ 100........ 0.7 lbs (0.3 kg)
All other models................ 0.2 lbs (0.1 kg)
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
A-4
A-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
Shipping weight
Included Parts
CVEQ 100, SVEQ 100........ 3 lbs (2 kg)
All other models................ 2 lbs (1 kg)
These items are included in each order of the CVEQ 100 or
SVEQ 100.
Vibration......................................... ISTA 1A in carton (International Safe
Transit Association)
Listings............................................ UL, CUL
Included parts
Replacement
part number
CVEQ 100 or
60-812-01
60-813-01
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF............................................... 30,000 hours
SVEQ 100
Warranty......................................... 3 years parts and labor
User's manual
12 VDC, 2 A external power supply
Rubber feet (not attached)
IEC power cord
70-055-01
These items are included in each order of the CVEQ 100 AAP or
SVEQ 100 AAP.
Included parts
Replacement
part number
CVEQ 100 AAP (black) or
SVEQ 100 AAP (black) or
CVEQ 100 AAP (white) or
SVEQ 100 AAP (white)
User's manual
70-663-02
70-664-02
70-663-03
70-664-03
12 VDC, 2 A external power supply
IEC power cord
70-055-01
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
A-6
A-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
These items are included in each order of the CVEQ 100 MAAP
or SVEQ 100 MAAP.
Optional Accessories
These items are optional mounting accessories for the CVEQ 100
or SVEQ 100.
Included parts
Replacement
part number
Description
Part number
60-190-20
CVEQ 100 MAAP (black) or
SVEQ 100 MAAP (black) or
CVEQ 100 MAAP (white) or
SVEQ 100 MAAP (white) or
CVEQ 100 MAAP (RAL9010) or
70-667-02
70-668-02
70-667-03
70-668-03
70-667-05
RSF 123 VersaTools® rack shelf kit
RSB 123 VersaTools rack shelf
RSU 126 6" deep universal rack shelf kit
RSB 126 6" deep basic rack shelf
60-604-21
60-190-10
60-604-11
RSU 129 1U universal rack shelf kit
RSB 129 1U basic rack shelf
60-190-03
60-604-01
70-212-01
70-077-01
70-077-02
70-367-01
SVEQ 100 MAAP (RAL9010)
User's manual
70-668-05
MBU 123 under-desk mount kit
MBU 125 under-desk mount kit
MBD 125 through-desk mount kit
MBB 100 back of the rack mount kit
12 VDC, 2 A external power supply
IEC power cord
70-055-01
These items are included in each order of the CVEQ 100 D or
SVEQ 100 D.
These items are optional cables and adapters for the CVEQ 100
or SVEQ 100.
Included parts
Replacement
part number
Description
Part number
22-129-0X
CVEQ 100 D composite
video audio line driver
60-867-01
MHR-2P Plenum S-video cable
MHR-2 Non-Plenum S-video cable
22-123-0X
or
SVHSF-BNCM adapter (S-video female to
2 male BNCs)
26-541-0X
SVEQ 100 D S-video audio
line driver
60-868-01
RCAF-BNCM/10 adapter (RCA female to
BNC male, Qty. 10)
100-229-01
IN8906
Faceplate, black
Faceplate, white
AV RCA/6 cable (RCA male to male 6')
Decora® wall plate, black
Decora® wall plate, white
12 VDC, 2 A external power
supply
70-055-01
IEC power cord
Tweeker (small screwdriver)
User’s manual
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
A-8
A-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications, Part Numbers, Accessories, cont’d
These items are optional accessories for the CVEQ 100 D or
SVEQ 100 D.
Accessory
Part number
MHR-2 mini high resolution non-plenum
cable, bulk
22-123-xx
MHR-2P mini high resolution plenum
cable, bulk
22-129-xx
22-145-xx
22-146-xx
22-098-xx
22-164-xx
26-316-xx
IN8906, IN8920
Various
RG59 high resolution non-plenum cable,
bulk
RG59P high resolution plenum cable,
bulk
RG6 super high resolution non-plenum
cable, bulk
RG6P super high resolution plenum
cable, bulk
MHR-2 SV mini high resolution S-video
cables
AV RCA cable
STP cable
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
CVEQ 100 and SVEQ 100 Series • Specifications and Parts
A-10
A-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Template
Cut-out Template
Decora Models Dimensions
Dimensions are shown in inches [mm}.
Always check and go by the dimensions given in this
N
appendix. The template is not full size.
Cut-Out Template for the Extron
CVEQ 100 D & SVEQ 100 D
.060 [1.524]
.600 [15.500]
.100 [2.540]
2.79"
(7.09 cm)
2.830 [71.882]
0.000 [0.000]
2.720 [69.088]
2.040 [51.816]
1.465 [37.211]
Wall Plate
1.75"
(4.5 cm)
0.790 [20.066]
Location of Line Driver
0.110 [2.794]
0.000 [0.000]
2.720 [70.000]
2.8"
(7.1 cm)
4.50"
(11.43 cm)
SURFACE
CUT-OUT AREA
FOR
To install
FURNITURE
MOUNT
line driver
directly into
furniture or wall,
cut along this line.
Front View
Side View
TEMPLATE IS NOT FULL SIZE
CVEQ 100 and SVEQ 100 Series • Dimensions and Template
CVEQ 100 and SVEQ 100 Series • Dimensions and Template
B-2
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions and Template
CVEQ 100 and SVEQ 100 Series • Dimensions and Template
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
|