EVERFOCUS
Indoor Pendent Dome Camera
Operation Instructions
Model No. EPD200
Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1. Do not install the camera near electric or magnetic fields.
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer,
audio speakers since the magnetic fields generate from above devices will distort the video
images.
2. Never disassemble the camera nor put impurities in it.
Disassembly or impurities may result in trouble or fire.
3. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
4. Keep the power cord away from water and liquid.
Touching the wet power cord may result in electric shock.
5. Never install the camera in areas exposed to water, oil or gas.
Water, oil or gas may result in failure, electric shock or fire.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
Pickup Device
Video Format
Scanning System
1/3" SONY Super HAD CCD
NTSC or PAL
NTSC: 525 TV lines, 60 fields/sec.
PAL: 625 TV lines, 50 fields/sec.
510 x 492 (NTSC); 500 x 582 (PAL)
380 TVL
Picture Elements
Horizontal Resolution
Sensitivity
0.3 Lux /F=1.2
S/N Ratio
Electronic Shutter
Lens
Over 48dB(AGC Off)
1/50(1/60)~1/100,000
Vari-Focal or Fixed Lens
BNC 1.0Vp-p 75ohm
On/Off switch
Video Output
Back Light Comp..
Auto Gain Control
Flickerless
On/Off switch
On/Off switch
Auto White Balance
Auto IRIS
Auto
DC-Drive
Gamma Correction
Sync. Mode
0.45
Internal Sync.
Power Source
Two types:
12VDC/24VAC
12VDC only
Power Consumption
3W max.
BNC output x 1
Video Output Connector
2.5mm Lock x 1
AC 24V Power Connector + Video
2.5mm x 2-pin(for DC jack)
2.0mm x 2-pin(for BNC)
DC 12V Power Connector + Video
Weight
1.25mm x 4-pin, (1BNC, DC jack)
0.3 kg ; 0.66 lbs
Dimension
110mm(W)x 125(H)/ 4.33”(W) x4.92”(H)
Pendent Tube Diameter: 26mm/1.06”
0~50 ; 32°F~122°F (20%~80% Humidity)
CE, FCC
Operating Temperature
Certifications
2
Download from Www.Somanuals.com. All Manuals Search And Download.
DIMENSION DIAGRAM
a. Conduit Size
26mm/1.06”
b.
80mm/3.15””
125mm/4.92”
90mm/3.54”
110mm/4.33”
HARDWARE OVERVIEW
3
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Front panel design (For Vari-Focal Lens Model)
BLC – Back Light
Compensation
IRIS LEVEL
CONTROL
AGC (Automatic
Gain Control)
FL(Flickerless)
BNC Pigtail Slot for
Focusing and
Testing Module
b. Front panel design (For Fixed Lens Model)
BLC – Back Light
Compensation
FL(Flickerless)
AGC (Automatic
Gain Control)
ES(Electronic
Shutter)
BNC Pigtail Slot for
Focusing and
Testing Module
INSTALLATION
4
Download from Www.Somanuals.com. All Manuals Search And Download.
This section covers simple steps and detail installation. Please follow instruction for preventing
any unnecessary damage.
Simple Steps:
1. Connect to 26mm/1.06” EMT Conduit Pipe and lock it with Hex Wrench
2. Open camera bubble cover
3. Connect to testing monitor(optional accessories)
4. Adjust lens, camera position
5. Optional adjust camera setting on Dip Switch
1. Mount Camera
2.5mm Hex
Wrench
26mm EMT
Conduit Pipe
Set Screws
Camera
a. Pre-install 26mm/1.06” EMT conduit pipe and wire video and power cables though conduit
pipe. Connect power and video to the camera.
b. Locking pipe with camera by tightening set screws with supplied Hex wrench.
Note!! When connect to 12VDC with Power Extension cable . Please make sure you
connect powr +,- correctly. Wrong connection may damage the camera.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
White (+)
Black (-)
2. Open Camera Bubble Cover
Turn the camera bubble until you see the arrow face to here.
3. Connecting to testing monitor EN220
Connect the BNC Pigtail accessory to the front of the module for help with focusing or video
testing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Adjust Camera Position and Lens
a.Adjust camera position (Tilt angle up to 90 degree): Adjust camera to the position you
like. The turning angel is up to 90 degree. Use ‘tool-less’ screws on the side of the module
to secure position.
Tool-less Screws
90 Degree
b. Zoom and focus adjustments (For Vari-focal Lens Model)
After the camera was installed, the zoom and focus of the lens must be adjusted.
(1) Loosen the zoom ring knob, and then turn the ring towards <W> or <T> as necessary to
obtain the desired view range.
W side (Zoom out)
The viewing range will be wider and the subject is smaller.
T side (Zoom in)
The viewing range will be smaller and the subject is larger.
(2) Loosen the focus ring knob, then turn the ring towards <∞> or <N> as necessary to
obtain the clear video image.
(3) Repeat steps 1 and 2 until the best image is obtained.
Once the lens setting finished, tighten the zoom ring and the focus ring knobs.
CAMERA SETTING
¾ BLC (Back Light Compensation)
When BLC is turned on, the AGC, FL and IRIS operating point is determined by averaging over
the center area instead of entire field-of-view, so that a dimly-lit foreground object at center area
can be clearly distinguished from brightly-lit backgrounds. BLC should not be used unless it is
needed to compensate for back-light.
The default setting is OFF. For Auto-Iris lens model, the brightness can also be adjusted via the
Iris level control VR.
¾ AGC (Automatic Gain Control)
AGC ON: The sensitivity increases automatically when light is low.
AGC OFF: A-low-noise picture is obtained under a low light condition.
The default setting is ON.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
¾ FL (Flickerless)
When picture flicker fiercely, turn FL on, then the camera will stabilize the speed of electronic
shutter at 1/100(S)(NTSC) or 1/120(S)(PAL) automatically, and reduce the flicker immediately.
The default setting is OFF.
¾IRIS Level Control (For Vari-Focal Lens Model)
Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens.
•Turn counterclockwise to L to get darker picture.
•Turn clockwise to H to get brighter picture.¾Electronic Shutter (For Fixed Lens Model)
ES ON: The camera continuously adjusts the shutter speed from 1/60 (NTSC), 1/50 (PAL) second
to 1/100,000 second according to the luminance conditions of the scene.
ES OFF: The shutter speed is fixed at 1/60 (NTSC),1/50 (PAL) second.
Set ES OFF, when auto iris lens is used or flicker is observed under a very bright fluorescent lamp.
Otherwise, turn ES on for optimum performance.
EverFocus Electronics Corp.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Europe Office:
Head Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: 49-2822-9394-0
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886-2-26982334
FAX: +886-2-26982380
China Office:
Room B-05D-1, KESHI PLAZA , Shangdi
USA L.A. Office:
Information Industry Base,
Haidian District, Beijing China 100085
TEL: +86-10-62973336/37/38/39
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844-8888
FAX: +1-626-844-8838
FAX: +86-10-62971423
Japan Office:
USA N.Y. Office:
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: +81-43-212-8188
FAX: +81-43-297-0081
415 Oser Avenue Unit S
Hauppauge, NY 11788
TEL: 631-436-5070
FAX: 631-436-5027
Your EverFocus product is designed and
manufactured with high quality materials and
components which can be recycled and
reused.
Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen
Materialien und Komponenten, die recycelt
und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from your
household waste.
Please, dispose of this equipment at your
local community waste collection/recycling
centre.
Bitte entsorgen Sie dieses Gerät bei Ihrer
örtlichen kommunalen Sammelstelle oder im
Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu erhalten, in
der wir leben!
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the environment
we live in!
P/N: MEFDG00400
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|