802.11b/g/n Draft 2.0
Wireless LAN USB Adapter
User Manual
Version: 1.0 (April, 2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
CATALOG
Chapter I: Product Information.............................................................................................. 3
1-1 Introduction and safety information ......................................................................... 3
1-2 Safety Information ................................................................................................... 4
1-3 System Requirements............................................................................................. 5
1-4 Package Contents................................................................................................... 5
1-5 Familiar with your new wireless network card ......................................................... 6
CHAPTER II: DRIVER INSTALLATION AND CONFIGURATION......................................... 7
2-1 Network Card Installation ........................................................................................ 7
2-2 Connect to Wireless Access Point......................................................................... 13
2-2-1 Using Edimax Utility .................................................................................... 13
2-2-2 Using Windows Zero Configuration............................................................. 19
2-3 Connection Profile Management ........................................................................... 22
2-3-1 Make a profile for an access point or wireless device................................. 22
2-3-2 Using 802.1x – Certification ........................................................................ 30
2-3-3 Using 802.1x - CA Server............................................................................ 32
2-4 View Network Statistics and Link Status................................................................ 34
2-4-1 Network Statistics........................................................................................ 34
2-4-2 Link Status .................................................................................................. 35
2-5 Advanced Settings................................................................................................. 37
2-6 QoS Setting........................................................................................................... 40
2-7 WPS Configuration................................................................................................ 42
2-7-1 WPS Setup - PBC (Push-Button Configuration).......................................... 43
2-7-2 WPS Setup - PIN ........................................................................................ 46
2-8 About..................................................................................................................... 48
CHAPTER III: APPENDIX................................................................................................... 50
3-1 Hardware Specification.......................................................................................... 50
3-2 Troubleshooting..................................................................................................... 51
3-3 Glossary................................................................................................................ 53
3-4 FCC and Other Compliance Statements ............................................................... 56
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter I: Product Information
1-1 Introduction and safety information
Thank you for purchasing this nMAX wireless network card! Excepting common wireless standards 802.11b/g,
this wireless network card is also 802.11 Draft-N compatible - data transfer rate is 300Mbps, and that’s six
times faster than 802.11g wireless network! 802.11 Draft-N also provides wider wireless coverage, so you don’t
have to worry if your computer is far from your wireless access point. This wireless network card also supports
MIMO (Multi-In, Multi-Out) technology, which uses two different radio channels to enhance data transfer rate
and wireless coverage.
With easy-to-install USB 2.0 interface - a very common expansion port of computers - plug this wireless
network card into any empty USB port of your computer, just that simple!
Other features of this router including:
„
„
„
„
„
„
Complies with 802.11b, 802.11g, 802.11 Draft 2.0-N standards
Provides high-efficiency antenna, expands the scope of your wireless network.
Provides QoS function: control the bandwidth required for different applications.
Supports major encryption methods like WEP, WPA, and WPA2 encryption.
Supports USB 2.0 interface - you can get it installed on your computer in just few seconds!
Provides wireless access control - prevent unauthorized network access to your network and
computer.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1-2 Safety Information
In order to keep the safety of users and your properties, please follow the following safety instructions:
1. This USB wireless network card is designed for indoor use only. DO NOT expose this network card to direct
sun light, rain, or snow.
2. DO NOT put this network card at or near hot or humid places, like kitchen or bathroom. Also, do not left this
wireless network card in the car in summer.
3. This network card is small enough to put in a child’s mouth, and it could cause serious injury or could be fatal.
If they throw the network card, the card will be damaged. PLEASE KEEP THIS NETWORK CARD OUT THE
REACH OF CHILDREN!
4. This network card will become hot when being used for long time (This is normal and is not a
malfunction). DO NOT put the network card on a paper, cloth, or other flammable objects after the network
card has been used for a long time.
5. There’s no user-serviceable part inside the network card. If you found that the network card is not working
properly, please contact your dealer of purchase and ask for help. DO NOT disassemble the network card by
your self, warranty will be void.
6. If the network card falls into water, DO NOT USE IT AGAIN BEFORE YOU SEND THE CARD TO THE
DEALER OF PURCHASE FOR INSPECTION.
7. If you smell something strange or even see some smoke coming out from the network card, switch the
computer off immediately, and call dealer of purchase for help.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3 System Requirements
„
„
„
„
An empty USB 2.0 port (May not work on USB 1.1 port, and performance will be greatly reduced)
Operation system: Windows 2000, XP, XP64,or Vista
CD-ROM drive
At least 100MB of available disk space
1-4 Package Contents
Before you starting to use this wireless network card, please check if there’s anything missing in the package,
and contact your dealer of purchase to claim for missing items:
□ One Wireless LAN USB Adapter
□ One English quick installation guide
□ One CD-ROM (Including all the software utilities, drivers and User’s Manual)
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1-5 Familiar with your new wireless network card
1. USB Connector
2. Connector Cap (To protect USB connector when not in use)
3. Link/Activity LED
3
2
1
LED Name Light Status
Description
Linked to a wireless access point /
Transferring data
Link /
On
Off
Activity
No wireless activity
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER II: DRIVER INSTALLATION AND CONFIGURATION
2-1 Network Card Installation
Please follow the following instructions to install your new wireless network card:
1. Insert the USB wireless network card into an empty USB 2.0 port of your computer when computer is
switched on. Never use force to insert the card, if you feel it’s stuck, flip the card over and try again.
2.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The following message will appear on your computer, click ‘Cancel’.
4. Insert device driver CDROM into the CD/DVD ROM drive of your computer, and execute ‘Setup.exe’
program in ‘Driver’ folder. Please read the end user license agreement and click ‘Yes’ to accept license
agreement.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
4. You can choose the configuration tool used to configure the wireless network card here. It’s recommended
to select ‘Edimax Configuration Tool’, which provides fully access to all function of this wireless network
card. If you prefer to use the wireless configuration tool provided by Windows XP or Vista, please select
‘Microsoft Zero Configuration Tool’, then click ‘Next’.
5. There are two wireless performance modes you can select here:
Optimize for WiFi mode
or
Optimize for performance mode
If you want to enhance wireless performance, please select ‘Optimize for performance mode’. However,
wireless compatibility is not guaranteed in this mode. If you want to use this mode, you may not be able to
communicate with older wireless devices and wireless access point, such as 802.11b devices, but the data
transfer rate will be enhanced in this mode. You can select this mode when you only plan to communicate
with 802.11 Draft-N devices.
If you want to keep compatibility and communicate with older wireless devices, please select ‘Optimize for
WiFi Mode’.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
When you select one mode, please click ‘Next>’ to continue. If you see ‘Found New Hardware’ message
again, please ignore it and wait.
6. Please click ‘install’ to run the driver installation process.
If you see ‘Found New Hardware’ message again, please ignore it and wait.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Please wait while the install procedure is running. When you see this message, please click ‘Finish’ to
complete the driver installation process.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
8. A new icon will appear at lower-right corner of your computer desktop, you can put the mouse cursor on
the icon, and the status of wireless card will be displayed as a popup balloon.
HERE!
9. When you want to configure your wireless connection, please right click on this icon, and a popup menu
will appear. You can click ‘Launch Config Utilities’ to start configuration program.
If you want to close configuration utility, please click ‘Exit’.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2 Connect to Wireless Access Point
There are two ways you can configure your wireless network card to connect to wireless access point: using
the Ralink configuration utility which comes with wireless card driver, and using built-in windows zero
configuration utility.
2-2-1 Using Edimax Utility
Please follow the following instructions to use Ralink configuration utility to connect to wireless access point.
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Configuration utility will scan for all wireless access points automatically. Scan results will be displayed
here, please check if the wireless access point with the SSID (the name of wireless access point) you
preferred is shown here.
If the wireless access point you wish to connect does not show here, please click ‘Rescan’ to try again,
until the one you preferred is displayed. You may have to click ‘Rescan’ for more than two times before you
can see the access point you wish to use here sometimes.
If you still can not see the access point you wish to use after clicking ‘Rescan’ for more than five times,
please move your computer closer to the location where the wireless access point is, or see instructions in
chapter 3-2 ‘Troubleshooting’.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are descriptions of every setup item:
SSID:
The Service Set IDentifier of wireless access point or other network device.
You can think it as the name of access point of wireless device.
BSSID:
The MAC address of wireless access point or other network device. Unlike SSID,
BSSID of every access point or network device is unique, and will not be the same
with others. So you can identify a single access point or wireless device from others
by BSSID, if they all have the same SSID.
Signal:
Shows the signal strength of access point or wireless device. Larger number
means better radio strength, which often means you’re not too far from that access
point or wireless device.
Channel:
Shows the channel number that access point or wireless device uses.
Encryption:
Shows the encryption method that access point or wireless device uses. If the
wireless access point does not enable encryption, you’ll see ‘None’ displayed here.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Authentication:
Shows the authentication mode that access point or wireless device uses. If the
wireless access point does not require authentication, you’ll see ‘Unknown’
displayed here.
Network Type: Shows the type of wireless connection. If it’s a wireless access point, ‘Infrastructure’ will be
displayed here; if it’s a computer or network device, ‘AdHoc’ will be displayed here.
Tips:
Wireless access point (Infrastructure) is a network device which acts as a bridge, to let
wired and wireless network devices communicate with each other.
AdHoc is another connection type. A computer or network device can establish a direct
wireless link with other computer or network device directly, without the help of
wireless access point.
3. Click the wireless access point or network device you wish to connect, it will be highlighted, then click
‘Connect’.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
If the access point you selected does not enable encryption (The content of ‘Encryption’ field of the access
point you selected is ‘None’, you’ll be connected to this wireless access point within one minute. Please jump
to step 6.
If the access point you selected enables encryption, please proceed to next step.
4. If the wireless access point does not have SSID, you’ll be prompted to input it here. Please ask the owner
of wireless access point and input the exact SSID here, then click ‘OK’ when ready. If the SSID you
provided here is wrong, you’ll not be able to connect to this access point.
If the wireless access point you selected have SSID, please skip this step.
5. If the wireless access point uses encryption, you have to input WEP passphrase or WPA preshared key.
Please ask the owner of the wireless access point you want to connect, and input the correct passphrase /
preshared key here, then click ‘OK’. If the value you inputted here is wrong, you will not be able to connect
to this wireless access point.
Authentication type is selected automatically, please don’t change it.
If the access point you selected does not enable encryption and does not require authentication,
please skip this step.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
6. You’ll see ‘Connected <-> SSID’ (‘SSID’ is the SSID of the wireless access point or wireless device you
connected to) message displayed at lower-left corner of configuration utility, congratulations, you’re
successfully connected to the access point or wireless device you selected!
7. You can put the mouse cursor over the Edimax configuration utility icon, and the brief information about
link status and signal strength of current wireless connection will be shown as a popup balloon.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2-2 Using Windows Zero Configuration
Windows XP and Vista has a built-in wireless network configuration utility, called as ‘Windows Zero
Configuration’ (WZC). You can also use WZC to configure your wireless network parameter:
1. Right-click Edimax configuration utility icon and select ‘Use Zero Configuration as Configuration utility.
2. Click ‘Start’ button (should be located at the bottom-left corner of windows desktop), click ‘Control Panel’,
then click ‘Network Connections’ in Control Panel.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Right-click ‘Wireless Network Connection’ (it may have a number as suffix if you have more than one
wireless network card, please make sure you right-click the ‘Ediamx 802.11n Wireless LAN Card), then
select ‘View Available Wireless Networks’.
4. All wireless access points in proximity will be displayed here. If the access point you want to use is not
displayed here, please try to move your computer closer to the access point, or you can click ‘Refresh
network list’ to rescan access points. Click the access point you want to use if it’s shown, then click
‘Connect’.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. If the access point is protected by encryption, you have to input its security key or passphrase here. It must
match the encryption setting on the access point.
If the access point you selected does not use encryption, you’ll not be prompted for security key or
passphrase.
6. If you can see ‘Connected’ message, the connection between your computer and wireless access point is
successfully established.
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3 Connection Profile Management
If you need to connect to different wireless access points at different time, like of access point of your home,
office, cyber cafe, or public wireless service, you can store the connection parameters (encryption, passphrase,
security etc, etc.) as a profile for every access point, so you don’t have to input these parameters every time
you want to connect to a specific wireless access point.
2-3-1 Make a profile for an access point or wireless device
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. There are two ways to add a new connection profile:
Create a new profile,
or
Add a profile from an existing wireless access point or wireless device
If you want to click new profile, click ‘Profile’ tab, then click ‘Add’ button:
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Or, you can add a connected wireless access point or wireless device to a profile by clicking ‘Site Survey’ tab,
then click ‘Add to Profile’ button:
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
And you can set the parameter for this connection here:
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are descriptions of every setup items:
Profile Name
Please give this profile a name, up to 32 alphanumerical characters and symbols
are allowed, but space is not allowed.
SSID
The SSID of the wireless access point or wireless device you selected will be
displayed here. But if the SSID of access point or wireless device is not available,
you have to input it here manually.
PSM:
Please select CAM (constantly awake mode, keep
(Power Saving
Mode)
the wireless radio activity when not transferring
data), or PSM (Power saving mode, switches radio off when not transferring data).
It’s recommended to choose ‘PSM’ if you’re using this network card with
notebook computer to help the battery live longer.
Network Type
Select network type (‘Ad Hoc’ or ‘Infrastructure’). If you’re adding a profile from an
existing access point or wireless device, it’s automatically selected and you don’t
have to change it.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TX Power
You can select the radio output power of wireless network card. You may not need
full radio power if you’re not far from wireless access point, and only use a high
setting here if you found that radio reception is bad.
If you don’t know which one to use, select ‘Auto’.
Preamble
This option is only available when the network type is ‘Ad hoc’. You can select
‘Auto’ or ‘Long Preamble’. Please select ‘Auto’ if you don’t know what it is.
RTS Threshold
Check the box and you can set RTS threshold manually here. Do not modify default
setting unless you know what it is.
Fragment
Threshold
Check the box and you can set fragment threshold
manually here. Do not modify default setting unless you know what it is.
Now click ‘Authentication and Security’ tab, and set the encryption and authentication settings.
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are descriptions of every setup items:
Authentication
Type
Select the authentication type of the wireless access
point or wireless device you wish to connect. If you’re adding a profile from an
existing access point or wireless device, the value will be selected automatically,
and please do not modify it.
If you select ‘LEAP’, the following message will be displayed. Please input LEAP
identity, password, domain name, and select encryption type. You can check ‘Show
Password’ box so the password you inputted will be displayed as you type, but not
replace by asterisk.
Encryption:
Select the encryption type of the wireless access point or wireless device you wish
to connect. If you’re adding a profile from an existing access point or wireless
device, the value will be selected automatically, and please do not modify it.
WPA
Input WPA preshared key here. If encryption is not
Preshared Key
enabled, or you select ‘WEP’ as encryption type, this field will be disabled and
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
grayed out.
WEP Key
You can select key type (Hex or ASCII) and input WEP key here. If encryption is not
enabled, or you select ‘WPA’ as encryption type, this field will be disabled and
grayed out.
Show Password
Use 802.1x
Check this box and all passphrases or security keys you inputted will be displayed
as you type, but not replace your input with asterisk.
Enable 802.1x wireless authentication. Please click ‘802.1x Setting’ button to set
802.1x parameters. (See next section).
After you finish all settings, click ‘OK’ to save settings and exit. The profile you just created will be displayed:
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the profile you wish to use, and click ‘Activate’ to use the profile you selected. You can only activate a
profile a time, and the profile that is activated currently will have a green check ( ) before its name. If the
wireless access point is not reachable, a red check ( ) will be displayed before its name.
If you want to change the connection parameters of a specific profile, just select it and click ‘Edit’ button, you’ll
be prompted to input the connection parameters, just like you’re creating a new profile.
If you no longer need a profile, select the profile then click ‘Delete’.
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3-2 Using 802.1x – Certification
After you click ‘802.1x Setting’, a new window will appear:
Here are descriptions of every setup items:
Authentication
Type
Please select an 802.1x authentication type here.
The type you select here must be identical to the type of the 802.1x authentication
type you’re using.
Session
You can enable or disable session resumption here.
If you don’t know if you should enable session resumption or not, please ask your
802.1x authentication administrator.
Resumption
Identity
Please input 802.1x identity here.
Password
Domain Name
Please input the password of 802.1x identity here.
Please input the domain name of 802.1x authentication here. This field will be
grayed out when authentication type is not ‘EAP-FAST’.
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Use Client
More..
If the authentication type you use is ‘PEAP’ or ‘TTLS’, you can use the certificate
stored on your computer. If the authentication type you use is ‘TLS/Smart Card’,
this box is always checked.
After you clicked this button, you’ll be prompted to select a certificate on your
computer.
Allow
This box is always checked and can not be modified.
unauthenticated
provision mode
Use protected
authentication
credential
If the authentication type you use is ‘EAP-FAST’ you can use protected
authentication credential by check this box.
Remove
Import
Remove the credential you imported previously.
Import the authentication credential file (PAC or al file format), you’ll be prompted to
select a credential file from your computer.
Protocol
You can select the protocol of tunneled authentication here. This pulldown menu is
only available when authentication type you use is ‘PEAP’ or ‘TTLS’. When you use
‘EAP-FAST’ as authentication type, the protocol setting is always ‘Generic Token
Card’ and can not be changed.
Identity
Please input the identity of tunneled authentication here.
(of tunneled
authentication)
Password
Please input the password of tunneled authentication here.
(of tunneled
authentication)
Password Mode
Please select the password mode of ‘EAP-FAST’ authentication mode.
This setting is hidden when the authentication type is not ‘EAP-FAST’.
After you finish all settings, click ‘OK’ to save settings and exit.
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-3-3 Using 802.1x - CA Server
If you want to use CA server, please click ‘CA Server’ tab. And the following message will be displayed:
Here are descriptions of every setup items:
Use certificate
chain
Check this box to enable the use of certificate chain.
Certificate
Issuer
Please select the issuer of certificate from this dropdown menu.
Check this box if you wish to allow intermediate certificates.
Allow
intermediate
certificates
Server name
Input the server name of CA server here.
Server name
must match
Check this box and the wireless configuration utility will check if the server name
of CA server
- 32 -
Download from Www.Somanuals.com. All Manuals Search And Download.
exactly
you set here is exactly matched with the CA server connected to. If they don’t
match, connection will be dropped.
Domain name
must end
Check this box and the wireless configuration utility will check the end of domain
name. If there’s anything wrong, connection will be dropped.
in specified name
After you finish all settings, click ‘OK’ to save settings and exit.
- 33 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-4 View Network Statistics and Link Status
The configuration utility provides information about network statistics and link status. If you want to know how
your wireless network card works, you can use these functions to get detailed information about the wireless
connection you’re using.
2-4-1 Network Statistics
Please follow the following instructions to check network statistics:
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Click ‘Statistics’ tab, and the statistics of wireless connection will be displayed:
- 34 -
Download from Www.Somanuals.com. All Manuals Search And Download.
All connection-related statistics is displayed here. You can click ‘Reset Counter’ to reset the statistics of all
items back to 0.
Click ‘OK’ to close the window.
2-4-2 Link Status
Please follow the following instructions to check network statistics:
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Click ‘Link Status’ tab, and information about current wireless connection will be displayed:
- 35 -
Download from Www.Somanuals.com. All Manuals Search And Download.
These information displayed here are updated every second, and here are descriptions of every item:
Status
Displays the SSID and BSSID of connected wireless access point or wireless
device (displayed as SSID <-> BSSID as shown in above picture. If there’s no
active connection currently, ‘Disconnected’ will be displayed here.
Extra Info
Displays the link status (‘Link is up’ or Link is down’, and the radio transmitting
power of your network card.
Channel
Displays the radio channel being used now.
Link Speed
Displays the link speed of data transmitting (Tx, in Mbps) and receiving (Rx, in
Mbps). Link speed is the maximum available data transfer speed of the wireless
connection, and depends on the radio signal quality of wireless connection.
Throughput
Link Quality
Displays the rate of data transmitting (Tx, in Kbps) and receiving (Rx, in Kbps).
Displays link quality (radio signal quality). When the link quality is better, the
wireless link speed will be better, too. Link quality is displayed by percentage and a
descriptive word (Good, normal, weak, and low).
Signal Strength 1
Signal Strength 2
Noise Level
Displays the radio signal strength of built-in antenna 1.
Displays the radio signal strength of built-in antenna 2.
Displays the percentage or level of noise (unusable) signal. If the value of this item
is high, data transfer rate will drop.
dBm
Check this box and the value of signal strength and noise level will be displayed in
dBm level instead of percentage.
There are several wireless statuses available at the bottom of this window.
For their explanations, please see chapter 3-3 ‘Glossary’.
- 36 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-5 Advanced Settings
This wireless network card provides several advanced settings for experienced wireless users. You can
change these settings to increase data transfer performance, or change operation mode.
Please follow the following instructions to set advanced wireless settings:
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Click ‘Advanced’ tab, and the following settings will appear:
- 37 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are descriptions of every setup items:
Wireless mode
Select wireless operation mode, available options are 802.11 B/G mix, 802.11 B
only, and 802.11 B/G/N mix. You can select 802.11 B/G/N mix to maximize wireless
compatibility with wireless access points and other wireless devices. Anyway, you
can set this setting to ‘802.11 B only’ when you’re going to communicate with old
802.11b wireless devices and you got problem using other two modes.
Wireless
This setting helps your network card to avoid interference with other wireless
devices when there are both 802.11b and 802.11g wireless devices in the same
place. It’s recommended to set this setting to ‘Auto’ , since enabling this setting will
slightly reduce the data transfer performance.
Protection
TX Rate
Normally, the wireless network card will adjust transfer rate automatically according
to wireless signal quality. However, you can fix the data transfer rate to a lower
fixed rate if you think there’s some problem about data transfer, or you’re too far
from wireless access point. It’s recommended to set this setting to ‘Auto’, unless
you really know the meaning of this setting.
Tx BURST
Check this box to accelerate the data transmit rate. It may not work with all wireless
access point and wireless devices.
Enable TCP
Window Size
Check this box and the configuration utility will adjust TCP window size
automatically, to get better performance. It should be safe for most of wireless
environments, but if you found some problem on data transfer, uncheck this box.
Fast Roaming at
Turn off RF
Check this box and you can adjust the threshold of when this wireless network
card should switch to another wireless access point with better signal quality. Only
adjust value when you understand what it means.
Click this button to switch wireless radio off, click it again switch wireless
radio on.
Select Your
Country Region
Code
Select the country / region code of the place you’re living.
Different country / region has different
regulations on wireless devices, and it’s forbidden
to use certain channel (radio frequency) in some
countries or regions. Please select the country and region code according to the
place you live.
- 38 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Show
When your computer is being authenticated by
Authentication
Status Dialog
wireless authentication server, a dialog window
with the process of authentication will appear.
This function is helpful to find out the problem when you can not be authenticated,
and you can provide this information to authentication server’s administrator for
debugging purpose.
Enable CCX
Enable Cisco Compatible eXtensions. CCX is a wireless feature developed by
Cisco used to improve the wireless performance with CCX compatible wireless
devices. Check this box if you need to connect to CCX-compatible wireless
devices.
Turn on CCKM
Check this box to enable CCKM (Cisco Centralized Key Management), which
enables wireless clients to roam between CCKM-enabled access points in very
short time.
Enable Radio
Measurement
When you’re connecting to CCX-compatible
access point, check this box to enable radio measurement function to improve
wireless connectivity.
Non-Serving
Channel
When you’re connecting to CCX-compatible
access point, check this box to enable measurement
on unused radio channels to improve wireless connectivity.
Measurements
Limit ---
Limit the time used for said measurement to a
certain time. Default value is 250.
milliseconds
After you finish the settings, click ‘Apply’ to apply new settings, and click ‘OK’ to close configuration utility.
- 39 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-6 QoS Setting
This wireless network card provides QoS (Quality of Service) function, which can improve the performance of
certain network applications, like audio / video streaming, network telephony (VoIP), and others. When you
enable WMM (Wi-Fi MultiMedia) function of this network card, you can define the priority of different kinds of
data, to give higher priority to applications which require instant responding. Therefore you can improve the
performance of such network applications.
Please follow the following instructions to set advanced wireless settings:
Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then click
‘Launch Config Utilities’.
Click ‘QoS’ tab, and the following settings will appear:
- 40 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Here are descriptions of every setup items:
WMM Enable
Check this box to enable WMM function. Please click ‘Apply’ button on the right of
this check box after you check or uncheck this box, so corresponding settings in
this window will be activated or deactivated respectively.
WMM - Power
Save Enable
Enable WMM power saving mode to save energy
and lets your battery live longer.
Setting...
Click this button to select the WMM data type which will suppress the function of
power saving. When this kind of data is transferring, power saving function will be
disabled. Available data types are AC_BK (Background / Low Priority), AC_BE
(Best Effort), AC_VI (Video First), and AC_VO (Voice First).
Direct Link
Enable or disable direct link setup (DLS) function.
Setup Enable
This function will greatly improve the data transfer rate between WMM-enabled
wireless devices. Please click ‘Apply’ button on the right of this check box after you
check or uncheck this box, so corresponding settings in this window will be
activated or deactivated respectively.
MAC Address
Timeout Value
Tear Down
Input the MAC address of another WMM-enabled
wireless device you wish to establish a direct link here, then click ‘Apply’ to add this
MAC address to DLS address table.
Input the timeout value of this WMM-enabled direct
link wireless device. If the wireless
device is not responding after this time, it will be removed from DLS table.
If you want to remove a specific wireless device from DLS table, select the device
and click this button to remove it.
After you finish the settings, click ‘OK’ to close configuration utility.
- 41 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7 WPS Configuration
Note: This function supports Windows XP/XP64 Operation System only.
Wi-Fi Protected Setup (WPS) is the latest wireless network technology, which makes wireless network setup
become very simple. If you have WPS-enabled wireless access point, and you want to establish a secure
connection to it, you don’t have to configure the wireless access point and setup data encryption. All you have
to do is go to the WPS setup page of this wireless card, click a button, and then press a specific button on the
wireless access point you wish to establish a secure connection - just three simple steps!
For older wireless access points, it’s possible to perform a firmware upgrade to become a WPS-enabled
access point. Since they may not have a hardware button to press for WPS setup, you can use an alternative
WPS setup method – input the pin code. Every WPS-compatible wireless network card comes with a unique
WPS pin code; you can just input the code to wireless access point, and the wireless access point and wireless
network card will do the rest for you.
This wireless network card is compatible with WPS. To use this function, the wireless access point you wish to
connect to must support WPS function too. Now, please follow the following instructions to establish secure
connection between WPS-enabled wireless access point and your wireless network card:
- 42 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7-1 WPS Setup - PBC (Push-Button Configuration)
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then click
‘Launch Config Utilities’.
2. Click ‘WPS Configuration’ tab, and the following settings will appear:
- 43 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Push the ‘WPS’ button on your wireless access point (the button used to activate WPS standby mode may
have another name), or use other way to start WPS standby mode as the instruction given by your wireless
access point’s user manual.
4. Before you start to establish the wireless connection by using WPS, you can click ‘Rescan’ button to
search for WPS-enabled access points near you, to make sure the WPS function of your access point is
activated.
All access points found will be displayed. Please make sure the access point you wish to connect is displayed.
If not, please click ‘Rescan’ few more times. You can also click ‘Information’ button to see the detailed
information about selected access point.
- 44 -
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Click ‘PBC’ button now to start to establish wireless connection by WPS, and please be patient (This may
require several seconds to one minute to complete). When you see ‘WPS status is connected successfully’
message, means the connection between your wireless network card and access point is successfully
connected by WPS, and the information about access point you connected to will be displayed.
TIPS: You can push ‘WPS’ button on network card too, it’s the same as the ‘PBC’ button in
configuration utility.
Sometime WPS may fail, and you can click ‘PBC’ button few more times to try again. When an access point is
connected, you can click ‘Disconnect’ to disconnect your wireless network card from a connected access point,
or select another WPS-enabled wireless access point, then click ‘Connect’ to establish connection to selected
access point, if there are more than one WPS-enabled access point found. You can also click ‘Rotate’ button,
and next access point on the list will be selected to establish connection.
If you want to delete a found access point from the list, select it and click ‘Delete’ button.
- 45 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-7-2 WPS Setup - PIN
If the wireless access point you wish to connect supports PIN, please follow the following instructions to
establish connection to it:
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Click ‘WPS Configuration’ tab, and the following settings will appear:
- 46 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The PIN number of your wireless network card is an eight-digit number located at the upper-right position of
configuration utility. Remember it, and input the number to your wireless access point as the WPS PIN code
(Please refer to the user manual of your wireless access point for instructions about how to do this).
NOTE: The PIN code of every wireless network card is DIFFERENT. Please don’t use the
sample code shown here.
3. Click ‘PIN’ button now, and wait for few seconds to one minute. If a wireless access point with correct PIN
code is found, you’ll be connected to that access point:
You may have to click ‘PIN’ for few more times to try again. If you still can not connect to access point by this
way, please make sure the PIN code you provided to access point is correct.
- 47 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2-8 About
The ‘About’ tab provides you the information about version numbers of configuration utility, firmware, and other
important information about your wireless network card.
Please follow the following instructions to see these information:
1. Right-click the Edimax configuration utility icon located at lower-right corner of computer desktop, then
click ‘Launch Config Utilities’.
2. Click ‘About’ tab, and the following settings will appear:
- 48 -
Download from Www.Somanuals.com. All Manuals Search And Download.
If you need assistance about network problem, you’ll need these values. You can also click
‘WWW.EDIMAX.COM’ button to go to the web site of network card driver manufacturer and get more
information about your wireless network card.
Please click ‘OK’ to close configuration utility.
- 49 -
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER III: APPENDIX
3-1 Hardware Specification
Standards: IEEE 802.11b/g/Draft-N
Interface: USB 2.0 (USB 1.1 Compatible)
Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medical Band)
Data Rate:
11b: 1/2/5.5/11Mbps
11g: 6/9/12/24/36/48/54Mbps
11n (20MHz): MCS0-15, 32 with Half Guard Interval Support (up to 144Mbps)
11n (40MHz): MCS0-15, 32 with Half Guard Interval Support (up to 300Mbps)
WEP 64/128, WPA, WPA2
Securities:
Cisco CCX V1.0, V2.0 & V3.0 Compliance
Antenna: Internal 2 Antennas with Two TX and Two RX
Drivers: Windows 2000/XP/2003/Vista Server
LEDs: Link/Activity
Transmit Power: 16dBm ± 2dBm
Temperature: 32~131°F (0 ~ 55°C)
Humidity: 10-95% (NonCondensing)
Certification: FCC, CE
- 50 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2 Troubleshooting
If you encounter any problem when you’re using this wireless network card, don’t panic! Before you call your
dealer of purchase for help, please check this troubleshooting table, the solution of your problem could be very
simple, and you can solve the problem by yourself!
Scenario
Solution
I can’t find any wireless access
point / wireless device in ‘Site
Survey’ function.
1. Click ‘Rescan’ for few more times and see if you can find any
wireless access point or wireless device.
2. Please move closer to any known wireless access point.
3. ‘Ad hoc’ function must be enabled for the wireless device you
wish to establish a direct wireless link.
4. Please adjust the position of network card (you may have to
move your computer if you’re using a notebook computer) and
click ‘Rescan’ button for few more times. If you can find the
wireless access point or wireless device you want to connect by
doing this, try to move closer to the place where the wireless
access point or wireless device is located.
Nothing happens when I click
‘Launch config utilities’
1. Please make sure the wireless network card is inserted into your
computer’s USB port. If the Ralink configuration utility’s icon is
black, the network card is not detected by your computer.
2. Reboot the computer and try again.
3. Remove the card and insert it into another USB port.
4. Remove the driver and re-install.
5. Contact the dealer of purchase for help.
I can not establish connection
with a certain wireless access
point
1. Click ‘Connect’ for few more times.
2. If the SSID of access point you wish to connect is hidden (nothing
displayed in ‘SSID’ field in ‘Site Survey’ function), you have to
input correct SSID of the access point you wish to connect.
Please contact the owner of access point to ask for correct
SSID.
3. You have to input correct passphrase / security key to connect an
access point with encryption. Please contact the owner of
access point to ask for correct passphrase / security key.
4. The access point you wish to connect only allows network cards
with specific MAC address to establish connection. Please go to
‘About’ tab and write the value of ‘Phy_Addess’ down, then
present this value to the owner of access point so he / she can
- 51 -
Download from Www.Somanuals.com. All Manuals Search And Download.
add the MAC address of your network card to his / her access
point’s list.
The network is slow / having
problem when transferring large
files
1. Move closer to the place where access point is located.
2. Enable ‘Wireless Protection’ in ‘Advanced’ tab.
3. Try a lower TX Rate in ‘Advanced’ tab.
4. Disable ‘Tx Burst’ in ‘Advanced’ tab.
5. Enable ‘WMM’ in ‘QoS’ tab if you need to use multimedia /
telephony related applications.
6. Disable ‘WMM – Power Save Enable’ in ‘QoS’ tab.
7. There could be too much people using the same radio channel.
Ask the owner of the access point to change the channel
number.
Please try one or more solutions listed above.
- 52 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3-3 Glossary
1. What is the IEEE 802.11g standard?
802.11g is the new IEEE standard for high-speed wireless LAN communications that provides for up to
54 Mbps data rate in the 2.4 GHz band. 802.11g is quickly becoming the next mainstream wireless LAN
technology for the home, office and public networks.
802.11g defines the use of the same OFDM modulation technique specified in IEEE 802.11a for the 5
GHz frequency band and applies it in the same 2.4 GHz frequency band as IEEE 802.11b. The 802.11g
standard requires backward compatibility with 802.11b.
The standard specifically calls for:
A. A new physical layer for the 802.11 Medium Access Control (MAC) in the 2.4 GHz frequency band,
known as the extended rate PHY (ERP). The ERP adds OFDM as a mandatory new coding scheme
for 6, 12 and 24 Mbps (mandatory speeds), and 18, 36, 48 and 54 Mbps (optional speeds). The ERP
includes the modulation schemes found in 802.11b including CCK for 11 and 5.5 Mbps and Barker
code modulation for 2 and 1 Mbps.
B. A protection mechanism called RTS/CTS that governs how 802.11g devices and 802.11b devices
interoperate.
2. What is the IEEE 802.11b standard?
The IEEE 802.11b Wireless LAN standard subcommittee which formulates the standard for the industry.
The objective is to enable wireless LAN hardware from different manufactures to communicate.
3. What does IEEE 802.11 feature support?
The product supports the following IEEE 802.11 functions:
z
z
z
z
z
z
CSMA/CA plus Acknowledge Protocol
Multi-Channel Roaming
Automatic Rate Selection
RTS/CTS Feature
Fragmentation
Power Management
4. What is Ad-hoc?
An Ad-hoc integrated wireless LAN is a group of computers, each has a Wireless LAN card, Connected
as an independent wireless LAN. Ad hoc wireless LAN is applicable at a departmental scale for a branch
or SOHO operation.
5. What is Infrastructure?
An integrated wireless and wireless and wired LAN is called an Infrastructure configuration.
Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless
application for mobile workers.
6. What is BSS ID?
A specific Ad hoc LAN is called a Basic Service Set (BSS). Computers in a BSS must be configured with
the same BSS ID.
- 53 -
Download from Www.Somanuals.com. All Manuals Search And Download.
7. What is WEP?
WEP is Wired Equivalent Privacy, a data privacy mechanism based on a 40 bit shared key algorithm, as
described in the IEEE 802 .11 standard.
8. What is TKIP?
TKIP is a quick-fix method to quickly overcome the inherent weaknesses in WEP security, especially the
reuse of encryption keys. TKIP is involved in the IEEE 802.11i WLAN security standard, and the
specification might be officially released by early 2003.
9. What is AES?
AES (Advanced Encryption Standard), a chip-based security, has been developed to ensure the highest
degree of security and authenticity for digital information, wherever and however communicated or
stored, while making more efficient use of hardware and/or software than previous encryption standards.
It is also included in IEEE 802.11i standard. Compare with AES, TKIP is a temporary protocol for
replacing WEP security until manufacturers implement AES at the hardware level.
10. Can Wireless products support printer sharing?
Wireless products perform the same function as LAN products. Therefore, Wireless products can work
with Netware, Windows 2000, or other LAN operating systems to support printer or file sharing.
11. Would the information be intercepted while transmitting on air?
WLAN features two-fold protection in security. On the hardware side, as with Direct Sequence Spread
Spectrum technology, it has the inherent security feature of scrambling. On the software side, WLAN
series offer the encryption function (WEP) to enhance security and Access Control. Users can set it up
depending upon their needs.
12. What is DSSS? What is FHSS? And what are their differences?
Frequency-hopping spread-spectrum (FHSS) uses a narrowband carrier that changes frequency in a
pattern that is known to both transmitter and receiver. Properly synchronized, the net effect is to
maintain a single logical channel. To an unintended receiver, FHSS appears to be short-duration
impulse noise. Direct-sequence spread-spectrum (DSSS) generates a redundant bit pattern for each bit
to be transmitted. This bit pattern is called a chip (or chipping code). The longer the chip is, the greater
the probability that the original data can be recovered. Even if one or more bits in the chip are damaged
during transmission, statistical techniques embedded in the radio can recover the original data
without-the need for retransmission. To an unintended receiver, DSSS appears as low power wideband
noise and is rejected (ignored) by most narrowband receivers.
13. What is Spread Spectrum?
Spread Spectrum technology is a wideband radio frequency technique developed by the military for use
in reliable, secure, mission-critical communication systems. It is designed to trade off bandwidth
efficiency for reliability, integrity, and security. In other words, more bandwidth is consumed than in the
case of narrowband transmission, but the trade off produces a signal that is, in effect, louder and thus
easier to detect, provided that the receiver knows the parameters of the spread-spectrum signal being
broadcast. If a receiver is not tuned to the right frequency, a spread –spectrum signal looks like
background noise. There are two main alternatives, Direct Sequence Spread Spectrum (DSSS) and
Frequency Hopping Spread Spectrum (FHSS).
- 54 -
Download from Www.Somanuals.com. All Manuals Search And Download.
14. What is WMM?
Wi-Fi Multimedia (WMM), a group of features for wireless networks that improve the user experience for
audio, video and voice applications. WMM is based on a subset of the IEEE 802.11e WLAN QoS draft
standard. WMM adds prioritized capabilities to Wi-Fi networks and optimizes their performance when
multiple concurring applications, each with different latency and throughput requirements, compete for
network resources. By using WMM, end-user satisfaction is maintained in a wider variety of
environments and traffic conditions. WMM makes it possible for home network users and enterprise
network managers to decide which data streams are most important and assign them a higher traffic
priority.
15. What is WMM Power Save?
WMM Power Save is a set of features for Wi-Fi networks that increase the efficiency and flexibility of
data transmission in order to conserve power. WMM Power Save has been optimized for mobile devices
running latency-sensitive applications such as voice, audio, or video, but can benefit any Wi-Fi device.
WMM Power Save uses mechanisms included in the IEEE 802.11e standard and is an enhancement of
IEEE 802.11 legacy power save. With WMM Power Save, the same amount of data can be transmitted
in a shorter time while allowing the Wi-Fi device to remain longer in a low-power “dozing” state.
16. What is GI?
GI stands for Guard Interval. It’s a measure to protect wireless devices from cross- interference. If there
are two wireless devices using the same or near channel, and they are close enough, radio interference
will occur and reduce the radio resource usability.
17. What is STBC?
STBC stands for Space-Time Block Coding, which is a technique used to transfer multiple copies of data
by multiple antenna, to improve data transfer performance. By using multiple antennas, not only data
transfer rate is improved, but also the wireless stability.
18. What is WPS?
WPS stands for Wi-Fi Protected Setup. It provides a simple way to establish unencrypted or encrypted
connections between wireless clients and access point automatically. User can press a software or
hardware button to activate WPS function, and WPS-compatible wireless clients and access point will
establish connection by themselves. There are two types of WPS: PBC (Push-Button Configuration) and
PIN code.
- 55 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4 FCC and Other Compliance Statements
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This device and its antenna must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the
authority to operate equipment.
- 56 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to
avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna
shall not be less than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal
Equipment and the mutual recognition of their conformity (R&TTE)
The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal
Equipment and Satellite Earth Station Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However, special
attention must be paid to the dangers of electric shock and static electricity when working with electrical
equipment. All guidelines of this and of the computer manufacture must therefore be allowed at all times to
ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria, Belgium, Denmark, Finland,
France, Germany, Greece, Ireland, Italy, Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the
United Kingdom.
The ETSI version of this device is also authorized for use in EFTA member states: Iceland, Liechtenstein,
Norway, and Switzerland.
EU Countries Not intended for use
None.
- 57 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|