USB 2.0 - 2.5" PATA Hard Drive Enclosure
DX-PHD25
USER GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Setting up your hard drive enclosure
DX-PHD25
3
Connect the drive’s data connector to the corresponding
connector on the enclosure circuit board.
Top and Front
2.5” PATA hard drive
4
Slide the drive tray, with drive attached, into the enclosure.
#
Item
Description
Activity LED
LED turns on when the hard drive is
turned on.
LED blinks when the hard drive is active.
1
USB 2.0 port
Connect a USB cable to this port and to
your computer.
2
3
Backup button
Press to initiate backup of selected files
on your computer.
5
Replace the two screws on the side panel.
Setting up your hard drive
Connecting the enclosure to your
computer
enclosure
Cautions:
Notes:
• Use only the accessories provided in the accessory package.
• Make sure that you first touch an unpainted, grounded metal object
to discharge any static electricity stored on your clothing or body
before touching any electronic components.
• Handle the printed circuit board (PCB) by the edges only. Avoid
touching the electronic components.
• Make sure you have installed the hard drive into the enclosure before
connecting the enclosure to your computer.
• A new hard drive must be initialized and partitioned before it will
appear in Windows Explorer or on your Mac desktop. Refer to your
hard drive manufacturer’s documentation, or see “Formatting the
hard drive in Windows” on page 4.
• Connect the hard drive enclosure to your computer before inserting
the software CD into your optical drive.
To connect the enclosure to your computer:
Installing your hard drive in the enclosure
To install your hard drive in the enclosure:
• Connect the Mini B type connector on the USB Y cable (provided)
to the enclosure, then plug the other end of the cable to your
computer. Connect both USB-A type connectors to the computer
to make sure that the enclosure has sufficient power. A good rule
of thumb would be to use one connector initially, then if your
computer does not recognize the drive, plug in the second
connector.
1
Remove the two screws from the left side panel.
Additional USB 2.0 A type male connector
for additional power (use if required)
USB 2.0 A type male connector
for data and bus power
2
Remove the plastic end cap and circuit board.
USB 2.0 Mini B type male
connector for data and bus power
Download from Www.Somanuals.com. All Manuals Search And Download.
4
DX-PHD25
Setting up your hard drive enclosure
Formatting the hard drive in Windows
Note: Formatting is only required for a new hard drive. Do not format a
drive that contains valuable data that you want to save.
To format the hard drive using Windows:
1
Right click My Computer (or Computer, depending on what
Optional USB 2.0 Y
connector for additional
power (if necessary)
version of Windows you have), then click Manage.
2
3
Under Storage on the LEFT pane, select Disk Management.
Locate the new drive, right click on the partition to be formatted,
then click Format.
4
Follow the prompts selecting the file system and other choices
you want, then click OK.
Creating a new partition in Mac OS X 10.4 or higher
If you are using a new hard drive, you may need to initialize it first.
Initialize your internal hard drive using Drive Setup from the Mac OS
CD that came with your computer.
The operating system automatically detects and sets up the new
drive.
If the drive is correctly detected, a new drive letter is assigned to
the enclosure.
• For PCs, the new drive letter appears in My Computer.
• For Macintosh computers, the new drive letter appears on
the desktop.
Note for Windows users: If you do not see an additional drive in your
system, you must format the new drive. See Windows online help for
more information.
To initialize a Hard Drive:
1
2
Start up your computer from the Mac OS CD.
Locate the Utilities folder on the Mac OS CD and double-click it
to open the folder.
3
4
Double-click Drive Setup to open the program.
From the list of drives, select the drive you want to initialize, then
click Initialize.
To format your hard drive with Mac OS Extended format:
This method of formatting hard drives provides for a more efficient use
of hard drive storage space.
Notes for Macintosh users: Select Disk Utilities from the Utilities
folder, then select the external enclosure and format the drive to meet
your requirements.
1
2
Click Custom Setup.
Select the Type menu in the Volume info area, then click Mac
OS Extended Format.
3
4
Resize the volumes if desired.
When ready, click OK, then click Initialize.
Partitioning and formatting a new hard
drive
If initialization fails, do the following:
1
2
Click Initialization Options from the Functions menu.
Select “Low level format”, then click OK. Choosing this option
adds significant time to the initialization process.
Creating a new partition in Windows
Caution: Doing the following will erase any existing data on the drive. If
the drive is damaged and you wish to recover the data, continuing
may overwrite the existing information!
Formatting the hard drive on a Mac
Note: For new hard drives, you need to initialize and partition your hard
To format the hard drive:
drive before it will appear in Windows Explorer.
1
2
3
4
Click Disk Utility (under Applications).
Select the new hard drive you are trying to install.
Click the Erase tab.
Choose a volume format and assign a name to the new drive,
then click Erase.
The best way to partition a new hard drive is to use the manufacturer’s
program. Most hard drives should come with a CD that includes the
installation program. If not, visit the manufacturer's website to see if a
download is available. If the manufacturer’s program is not available,
try the following instead:
To create a new partition in Windows:
Installing the software
1
Right click on My Computer, or Computer, depending on which
version of Windows you have) then click Manage.
Under Storage on the LEFT pane, select Disk Management.
Windows gives you the option to initialize the disk. If not, locate
the new drive, right click on it (where it reads “New Simple
Volume”), then click Initialize. (This step may not be required
for some hard drives).
The installation CD includes backup software to enable you to back up
your files.
2
Note: This Roxio BackOnTrack software runs only on Windows 7,
Windows Vista, and Windows XP computers using USB.
Important: Before installing the backup software, make sure that your
Windows operating system has been updated to the latest service
pack. To make sure you have the latest service pack, run Windows
Update. No additional driver is required.
3
4
Follow the prompts.
When the process is complete, locate your hard drive in the
bottom right pane. Right-click on the area with a status bar (to
the right of the “New Simple Volume” area), then click New
Partition.
Continue following the wizard’s directions. The recommended
partition type is “primary” and the recommended file system is
“NTFS.” Note that Windows XP limits FAT32 partitions to only
32GB.
To install Roxio BackOnTrack:
1
2
Save all files and close all programs.
Insert the included CD into your optical drive. The introductory
screen opens.
5
You should now be able to see the drive in Windows Explorer.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Setting up your hard drive enclosure
DX-PHD25
Or, if the screen does not open, locate the CD in Windows Explorer
and double-click Run.exe on the CD. The initial menu opens.
5
Read the license agreement, click “I accept..., “ then click NEXT.
The Choose Setup Type screen opens.
3
Click Install Backup Software. The Welcome screen opens.
6
Choose the setup type, then click Install to start installation. It
may take several minutes to install the software.
4
Click NEXT. The Roxio End-User License Agreement screen opens.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DX-PHD25
Using your enclosure
7
When installation is complete, the Setup Wizard Completed screen
opens.
Backing up your files
The Backup Files project lets you back up important files to a disc, hard
drive, or other storage device. A Backup Files project can be scheduled
to run daily, weekly, or monthly. Large backups are automatically
spread across as many discs as required.
Begin by selecting the drive or folder containing the files you would like
to archive. You can choose to archive all the files in the selected path or
just certain types of files. Several preset file categories are available.
Finally, schedule the project to run on a regular basis, or click the action
button to begin recording now.
Selecting files to back up
You can back up all of the files in a selected path or limit your project to
certain file categories. The following categories can be selected from
the project window: Email, Financial, Music, Photos, Productivity, and
Video and Recorded TV. You can also create one custom category.
8
Click FINISH to complete the installation.
Using your enclosure
Starting Roxio BackOnTrack
To start Roxio BackOnTrack:
1
Press the backup button (the button with the Dynex logo on it)
on the end of the enclosure.
Or, click Start, Roxio, the BackOnTrack folder, then click
BackOnTrack.
The first time you run the software, the Product Registration
screen opens.
By default, files will be selected based on the following criteria:
• All files in the selected path: All files on the drive or folder you
selected to archive.
• Email: All files with the following file name extensions --- .dbx,
.eml, .eudora, .mozilla, .msg, .pbx, .pst, .wab, .mbx, .mim,
.mime, .mlm, .wcm, and .pfc.
• Financial: All files with the following file name extensions
---.mbf, .mny, .ofc, .ptb, .ptdb, .q00, .q01, .q02, .q03, .q04, .q05,
.q06, .q07, .q08, .q09, .q98, .qba, .qbb, .qbi, .qbw, .qbx, .qdb,
.qdf, .qdt, .qel, .qif, .qph, .sdb, .t01, .t02, .t03, .t04, .t05, .t06,
.ta0, .ta1, .ta2, .ta3, .ta4, .ta5, .ta8, .ta9, .tax, .qmd, .mn4, .txf,
.tax2008, .tax2009, .tax2010, and .tax2011.
• Music: All files with the following file name extensions --- .669,
.aa, .aac, .aif, .aifc, .aiff, .amf, .amr, .apl, .au, .bwf, .cda, .cdda,
.dcm, .far, .flac, .it, .itz, .kar, .m3u, .m3url, .m4a, .m4b, .m4p,
.mdz, .mid, .midi, .miz, .mp1, .mp2v, .mp3, .mpga, .mpv2, .mtm,
.nsa, .nst, .ogg, .okt, .pls, .qcp, .ra, .rmi, .s3m, .s3z, .sd2, .shn,
.snd, .stm, .stz, .ult, .ulw, .voc, .wav, .wax, .wma, .wpl, .xm, .xpl,
.asx, and .m4u. Your entire My Music folder (Windows XP) or
Music folder (Windows Vista and Windows 7) is included if it is
located on the drive or in the folder you selected to archive.
• Photos: All files with the following file name extensions ---
.cam, .cr2, .crw, .dcr, .j2c, .j2k, .jfi, .jfif, .jif, .jp2, .jpe, .jpeg, .jpg,
.jpx, .k25, .kdc, .kqp, .mrw, .nef, .orf, .pef, .pmp, .raf, .raw, .srf,
.thm, .3ds, .ai, .ait, .ani, .art, .b3d, .bmp, .can, .cdr, .cdt, .cgm,
.clp, .cmt, .cpt, .cur, .dcx, .dds, .dib, .djvu, .drw, .drz, .dwg, .dxf,
.emf, .eps, .epsf, .fax, .fi, .fmf, .fpx, .fxo, .fxs, .g3, .g3n, .gif, .gmf,
.grb, .gro, .gsm, .gtif, .hpi, .icb, .icl, .ico, .ilbm, .img, .indd, .indt,
.iw44, .lbm, .lwi, .mac, .macp, .mix, .mng, .mod, .mpnt, .msp,
.ncr, .ngg, .nlm, .nol, .odg, .paint, .pat, .pcd, .pct, .pcx, .pdl, .pdp,
.pict, .pmd, .pmg, .png, .pnm, .pnt, .pntg, .pp4, .pp5, .ppm, .prm,
.psd, .psp, .pspimage, .pub, .qti, .qxd, .qxt, .rgb, .rle, .rppm, .sci,
2
Complete the Product Registration information as prompted (first
time only). The main screen opens.
3
To back up or restore files, follow the on-screen guide. For help,
press F1 or click Help.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Backing up your files
DX-PHD25
.sgi, .slddrw, .svg, .svg2, .targa, .tcw, .tga, .tif, .tiff, .vda, .vdx,
4
Type a file extension into the Extension text box. It is not
.vsd, .vss, .vst, .vsx, .vtx, .wmf, .wmz, and .wpg. Your entire My
Pictures folder (Windows XP) or Pictures folder (Windows Vista
and Windows 7) is included if it is located on the drive or in the
folder you selected to archive.
necessary to include the period.
5
6
Click Add. The file extension is added to the list box on the right.
Continue adding file extensions one at a time until you are
finished.
• Productivity: All files with the following file name extensions
--- .bk0, .bk1, .bk2, .bk3, .bk4, .bk5, .bk6, .bk7, .bk8, .doc, .docm,
.docx, .dot, .dotm, .dotx, .lwp, .odt, .ott, .pdf, .ps, .rtf, .txt, .wpd,
.wps, .wpt, .wri, .123, .dif, .ods, .ots, .qpw, .wk1, .wk3, .wk4,
.wks, .xla, .xlam, .xlr, .xls, .xlsb, .xlsm, .xlsx, .xlt, .xltm, .xltx, .odp,
.otp, .pot, .potm, .potx, .ppa, .ppam, .pps, .ppsm, .ppsx, .ppt,
.pptm, .pptx, .prz, .shw, .mpp, .wp, .wp6, .wmlx, and .oft. In
Windows XP, your my Documents folder, with the exception of
your My Pictures, My Videos, My DVDs, and My Music folders, is
folder with the exception of your Pictures, Videos, DVDs, and
Music folders, is included if it is located on the drive or in the
folder you selected to archive.
• Video and Recorded TV: All files with the following file name
extensions - .3g2, .3gp, .3gp2, .3gpp, .amc, .asf, .avi, .cin, .dv, .flc,
.ivf, .m15, .m1v, .m2p, .m2v, .m4e, .m4v, .m75, .mov, .mp4,
.mpe, .mpeg, .mpg, .mpm, .mpv, .mswmm, .nsv, .ogm, .qt, .qtl,
.qts, .rm, .rmvb, .rp, .rt, .rts, .rtsp, .rv, .sdv, .smi, .smil, .sml, .ssm,
.swf, .vfw, .wm, .wmd, .wmv, .wmx, .wvx, .xmz, .m1p, .mp2,
.vbs, .xtl, .dvr-ms, and .wtv. Your My Videos folder (Windows XP)
or Videos folder (Windows Vista and Windows 7) is included if it
is located on the drive or in the folder you selected to archive.
To remove a file extension from your list, click its name in the list
box, then click Remove.
7
Click OK to save your list as My Custom Category. This new
category is added to the list of file categories in the project
window.
Creating a new Backup Files project
1
displayed.
Click the Backup Files project.
Click Browse and use the Browse for Folder window to select the
drive or folder containing the files you would like to archive.
2
3
Note: Files stored on different source drives cannot be archived in the
same Backup Files project.
4
Select the types of files you wish to archive. Choose either All
files in the selected path or Only files in the following
categories.
If you selected only files in the following categories, select the file
categories you would like to archive. The choices are Email,
Financial, Music, Photos, Productivity, and Video and
Recorded TV. If you created a custom category, it will also be
available. See "Creating a custom category" on page 7 for more
information.
Tip: You can add to the list of file extensions included in any file category
by using the controls on the Backup options panel. See “Backup Files
options“ on page 8 for more information.
Creating a custom category
Note: Hold your mouse pointer over an icon to see the category it
represents.
Most computer files are defined by the two-, three-, or four-letter
extension placed at the end of their names. Plain text files, for example,
can be identified by their .txt file extension. When you record a Backup
Files project, the program is simply searching your computer for files
with extensions that correspond to the categories you selected. If you
want to archive files that are not included on any of the pre-defined
lists, you could choose to archive all files or edit one of the existing
categories (see “Backup Files options“ on page 8 for more information),
or you could create your own custom list of file extensions that will
appear as the category called My Custom Category.
5
If you want, place a check mark in the Only archive files
changed since checkbox to limit the backup to files that have
been modified since the date you select. To change the date, click
the date box arrow to open the calendar. When you click a date in
the calendar, the date is automatically entered into the date box.
Select a destination for your archived files from the Destination
Selection list. The destination can be a hard drive, a disc
recorder, or another type of storage device.
6
7
To compress or encrypt your backup, click Advanced and select
the appropriate settings:
To create a custom file category:
1
Click Options.
like the back up files created for this project to be
compressed. Compression reduces file size. The amount of
compression varies based on the types of files you back up.
Compressed files take longer to restore than uncompressed
files.
• Encryption-Click the Encrypt check box to require a
password to open or restore your backup project. Type a
password for this project in the space provided and again in
the confirmation box.
Caution: If you forget or lose your password, you will not be able to open
or restore your backup project.
8
Click the action
button to run the project now. To schedule
your project, choose one of the options in Step 3 on the project
window. For more information about scheduling a project, see
"Using the Backup Files scheduler" on page 8.
2
3
Click File Backup on the left side of the Options window. The File
Category options are displayed on the right side of the window.
Click My Custom Category.
-OR-
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DX-PHD25
Backing up your files
To save your project, click Save. Enter a name for the project,
then click OK. If you decided to run the project now, a progress
screen will inform you when the project has been completed.
Click Done to return to the project window.
Note: Scheduled projects must be saved before they can be run.
• The Backup Files project uses a scheduler that is part of the
Windows operating system. A system administrator has the
ability to prevent a computer user from using the scheduler or
running scheduled projects. If the Backup Files scheduler does
not work as expected, consult your system administrator.
• You can use your Windows scheduling software to customize
when your saved projects run. You can schedule a project to run
twice a week or once every hour. Save your project, then edit the
schedule using the Windows Scheduler.
9
To open and run a saved Backup Files project:
1
Click File. If the project is listed on the File menu, select it. If the
project is not listed, click Open and use the dialog box to
navigate to the project file. By default, project files are saved in
your Windows Vista and Windows 7 Documents folder or
Windows XP My Documents folder. The settings for that project
are displayed in the project window.
To run Windows Scheduler in Windows XP, click Start, All Programs,
Accessories, System Tools, Scheduled Tasks.
To run Windows Scheduler in Windows Vista and Windows 7, click
Start, All Programs, Accessories, System Tools, Task Scheduler.
2
Change the project settings as needed. Click Save to save your
original project is overwritten.)
If necessary, insert a blank or rewritable disc into the selected
destination drive.
Windows Scheduler. Remember that scheduling changes made
directly in the Windows Scheduler are not displayed in the Backup Files
project window.
3
4
Backup tips
Click the action
button to begin recording.
• All of the discs used in a Back Up Files project must be the same
general format.
A progress screen informs you when the project has been
completed.
• In a multi-disc Back Up Files project, files are assigned based on
the size of the first disc you use. If your first disc has a capacity of
650 MB, for example, no more than 650 MB will be burned on
any subsequent disc, even if it has a larger capacity. This also
means that no disc in a project can have a smaller capacity than
the first disc used in a project.
Using the Backup Files scheduler
Each time you create a Backup Files project, you have the option of
running it immediately or scheduling the project to run at a regular
interval that you choose.
• Discs used in a Back Up Files project are closed once they are
recorded. If you use write-once discs, you will not be able to add
additional data.
• To view a list of the files on a Back Up Files disc, open the .RFI file
placed on the disc.
To schedule a Backup Files project:
1
2
Open the Backup Files project.
Set up a new project or select a saved project. See "Creating a
new Backup Files project" on page 7 for more information on
starting a project.
3
Choose one of the scheduling options in the project window:
Backup Files options
• Run now-The project runs after you click the action button.
• Daily-The project runs every day at the time the project was
created.
Click Options on the control panel to open the Options window. Here
you find settings that can be used to customize your application.
Each available group of options is displayed in the left pane. Click the
name of an options group, and those option settings appear on the
right.
Each panel includes a Restore Defaults button that can be used to
restore the default settings for the options on that panel only.
• Weekly-The project runs once a week at the time and on the
day of the week the project was created.
• Monthly-The project runs once a month at the time and on
the day of the month the project was created.
4
5
Save your project by clicking Save. A save window appears.
Name the project, then click OK.
Note: Not all options are available for all drives or operating systems.
Note: If you schedule a monthly backup for the 31st day of the month,
your backup will be skipped during months with fewer than 31 days.
Backups scheduled on the 29th or 30th day of the month will also be
skipped during some months.
Backup options-File Backup panel
Use the Backup panel to customize the following Backup Files settings:
• File category options-Use this option to create a custom file
selection category or to add additional file types to any of the
preset categories.
Scheduler tips
The following tips will help you to better understand the scheduler:
• Scheduled projects must be saved before they can be run.
• Keep the following limitations in mind if you want a scheduled
project to be completed successfully while you are away from
your computer:
• Launch Backup Files when my external hard drive is
re-connected-Select this option to easily back up files to an
external hard drive.
• Verify data written to the disc after burning-A check mark
in this box adds a verification step to make sure that no errors
occur during the recording of your discs.
• Backup Files will not overwrite files without your permission.
This usually involves clicking on a series of message boxes. To
perform an unattended archive project, you may need to
change the hard drive destination for your archived files or
archive your files to a disc.
• If you are archiving files onto a disc, a blank disc must be
inserted in your drive when the project starts.
• Some of the energy conservation settings available for your
computer may keep a scheduled project from starting even if
the project launcher is open.
To create a new custom category called My Custom Category:
1
2
3
4
Select My Custom Category from the list of file categories.
Type a file extension into the Extension text box.
Click Add. The file extension is added to the list box on the right.
Continue adding file extensions one at a time until you are
finished.
To remove a file extension from your list, click its name in the list
box, then click Remove.
5
Click OK to save your list as My Custom Category.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Disconnecting the enclosure from your computer
DX-PHD25
To add file extensions to one of the preset file selection categories:
• Navigate through the directory tree in the project window.
When you find a file or folder you want to restore, select it by
clicking on its name.
1
Select the file category you would like to customize. The choices
are Email, Financial, Music, Photos, Productivity, and
Video & Recorded TV.
• Type all or part of a file or folder name into the Search box to
the right of the Browse button. Click Search. The search
results are displayed in the project window. If the file you
want to restore appears in the search results, select it by
clicking once on its name. If the file does not appear in the
search results, try using different search terms or looking in a
different backup file.
2
Enter the file extension you would like to add into the Extension
text box.
3
4
Click Add. The file extension is added to the list box on the right.
Continue adding file extensions one at a time until you are
finished.
5
Click OK.
7
8
Choose Browse from the Destination Selection menu and select
the location where your restored files will be saved.
Using one-touch backup
Click the action
button to begin restoring your files.
To use one-touch backup if you have set up a backup project:
• Press the One-Touch button on the HDD enclosure. The backup
process begins.
Restore files tips
• Restore Files can be used to restore as many files or folders as you
wish.
• Restore Files will not overwrite a file without getting your
permission.
• Backup files created with the Backup Files project can be
recognized by their .rfc file name extension. If you double-click
an .rfi file, the project launcher opens.
• The Restore Files search box does not support wildcard
expressions.
• System files cannot be restored to their original location if they
are in use by your computer's operating system.
To use one-touch backup if you have NOT set up a backup project:
1
Press the One-Touch button on the HDD enclosure. The Roxio
BackOnTrack software opens with the Backup Files page
displayed.
2
3
Follow the on-screen instructions to set up a backup project.
After a backup project is set up, push the One-Touch button to
backup your data.
4
To modify One-Touch backups in the future, follow the
instructions for setting up backup projects.
Restoring files
Disconnecting the enclosure
from your computer
The Restore Files project restores individual files and folders that you
have protected using the Backup Files project. With Restore Files, you
select a backup, search for the files or folder you would like to restore,
and then click the action button. The files will be restored to the
location you choose.
You can disconnect the enclosure at any time while the computer is
turned off. If, however, you want to disconnect it while the computer is
on, make sure that you do it correctly.
To disconnect the enclosure while Windows is running:
Note: If a drive window is open or the hard drive enclosure is active, close
any associated windows before trying to remove the enclosure.
1
Right-click the Safely Remove Hardware icon (located near
the clock on the taskbar).
2
3
Click the drive you want to unplug, then click STOP.
When Windows notifies you that it is safe to do so, unplug the
enclosure from your computer.
To disconnect the enclosure while Mac OS X is running:
1
2
Drag the USB icon into the TRASH.
Unplug the enclosure.
Uninstalling the backup software
To restore a file:
To uninstall the backup software in Windows:
1
Click the File Backup tab in the project list. A list of projects is
1
2
Open the Control Panel.
Click the Add or Remove Programs tab (Windows XP) or
Uninstall a Program (Windows Vista and 7).
displayed.
2
3
Click the Restore Files project. The project window opens.
If the backup file was saved on a disc, insert the disc into a
compatible disc drive.
3
4
5
Click Roxio BackOnTrack, then click Change/Remove
(Windows XP) or Uninstall (Windows Vista and Windows 7).
Follow the on-screen instructions to remove the software
completely from your computer.
After the software is uninstalled, restart your computer if
prompted.
4
5
Click Browse at the top of the Selective Restore project window. A
dialog box opens.
Use the dialog box to navigate to the backup file that contains
the files you would like to restore. After you have found the
backup file, click it, then click OK. The content of the backup file
appears as a directory tree in the project window.
6
Select the files and folders you would like to restore using one of
the following methods:
Download from Www.Somanuals.com. All Manuals Search And Download.
10
DX-PHD25
Troubleshooting
This equipment has been tested and found to comply within the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Troubleshooting
I do not see the additional drive in my system
Windows users: Partition and format the new hard drive by using
Disk Management in Windows.
enclosure.
My computer does not detect the enclosure
• Make sure that the USB cable is connected firmly to your
enclosure and computer.
• Make sure that the USB cable is not broken.
• Open the enclosure and make sure that all of the connections are
securely fastened.
• Use the rear USB ports on the back of the computer instead of the
front USB ports.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Check for motherboard compatibility issues.
• Check for hard drive compatibility issues.
There is a USB icon in the system tray, but I can’t find the hard disk in MY
COMPUTER
• Consult the dealer or an experienced technician for help.
FCC warning
Changes or modifications not expressly approved by the party
responsible for compliance with the FCC Rules could void the user’s
authority to operate this equipment.
• Make sure that the hard disk has been initialized and partitioned
before installation. See “Partitioning and formatting a new hard
drive” on page 4.
Canada ICES-003 statement
The Backup button doesn’t work
• Make sure you have installed the backup utility program. If the
backup utility program has been install successfully, an icon
shows on the toolbar when Windows is starting up.
This Class B digital apparatus complies with Canadian ICES-003.
This equipment complies with the applicable technical standards of
ICES 003:1997 in accordance with the measurement procedures
specified in CISPR22-96.
Specifications
IDE
Device interface
5.45 × 3.15 × 0.61 inches (138.5 × 80
× 15.5 mm)
Dimensions (WxLxH)
USB 2.0 Mini B type
Host interface
USB power
Power supply
Up to 320 GB 2.5” PATA HDD
Operating: 32~104°F (0~40°C)
20% to 80% non-condensing
FCC Class B, ICES-003
HDD supports
Operating temperature
Operating humidity
Certificate
Legal notices
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Legal notices
DX-PHD25
REPAIR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS YOUR
EXCLUSIVE REMEDY. DYNEX SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR THE BREACH OF ANY EXPRESS OR IMPLIED
WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA,
LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. DYNEX
PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE
PRODUCT, ALL EXPRESS AND IMPLIED WARRANTIES FOR THE PRODUCT,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF AND
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH
ABOVE AND NO WARRANTIES, WHETHER EXPRESS OR IMPLIED, WILL APPLY
AFTER THE WARRANTY PERIOD. SOME STATES, PROVINCES AND
JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE
OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO
PROVINCE.
One-year limited warranty
Dynex Products (“Dynex”) warrants to you, the original purchaser of this new
DX-PHD25 (“Product”), that the Product shall be free of defects in the
original manufacture of the material or workmanship for a period of one (1)
year from the date of your purchase of the Product (“Warranty Period”). This
Product must be purchased from an authorized dealer of Dynex brand
Products and packaged with this warranty statement. This warranty does not
cover refurbished product. If you notify Dynex during the Warranty Period of
a defect covered by this warranty that requires service, terms of this warranty
apply.
How long does the coverage last?
The Warranty Period lasts for one year (365 days) from the date you
purchased the Product. The purchase date is printed on the receipt you
received with the Product.
What does this warranty cover?
Contact Dynex:
For customer service please call 1-800-305-2204
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, Minnesota, U.S.A. 55423-3645
© 2011 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in
some countries. All other products and brand names are trademarks of their
respective owners.
During the Warranty Period, if the original manufacture of the material or
workmanship of the Product is determined to be defective by an authorized
Dynex repair center or store personnel, Dynex will (at its sole option): (1)
repair the Product with new or rebuilt parts; or (2) replace the Product at no
charge with new or rebuilt comparable products or parts. Products and parts
replaced under this warranty become the property of Dynex and are not
returned to you. If service of products and parts are required after the
Warranty Period expires, you must pay all labor and parts charges. This
warranty lasts as long as you own your Dynex Product during the Warranty
Period. Warranty coverage terminates if you sell or otherwise transfer the
Product.
How to obtain warranty service?
If you purchased the Product at a retail store location, take your original
receipt and the Product to the store you purchased it from. Make sure that
you place the Product in its original packaging or packaging that provides the
same amount of protection as the original packaging. If you purchased the
Product from an online web site, mail your original receipt and the Product to
the address listed on the web site. Make sure that you put the Product in its
original packaging or packaging that provides the same amount of
protection as the original packaging.
To obtain in-home warranty service for a television with a screen 25 inches or
larger, call 1-888-BESTBUY. Call agents will diagnose and correct the issue
over the phone or will have an Dynex-approved repair person dispatched to
your home.
Where is the warranty valid?
This warranty is valid only to the original purchaser of the Product in the
United States, Canada, and Mexico.
What does the warranty not cover?
This warranty does not cover:
•
•
•
•
•
•
•
•
•
•
•
•
Customer instruction
Installation
Set up adjustments
Cosmetic damage
Damage due to acts of God, such as lightning strikes
Accident
Misuse
Abuse
Negligence
Commercial use
Modification of any part of the Product
Plasma display panel damaged by static (non-moving) images
applied for lengthy periods (burn-in).
This warranty also does not cover:
•
•
•
Damage due to incorrect operation or maintenance
Connection to an incorrect voltage supply
Attempted repair by anyone other than a facility authorized by Dynex
to service the Product
•
•
•
Products sold as is or with all faults
Consumables, such as fuses or batteries
Products where the factory applied serial number has been altered or
removed
Download from Www.Somanuals.com. All Manuals Search And Download.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2011 BBY Solutions, Inc. All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
11-0170
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|