UNVENTED (VENT-FREE) BLUE FLAME GAS HEATER
SAFETY INFORMATION AND INSTALLATION MANUAL
MODELS GWN6, GWP6, GWN10, GWP10
GWN10T AND GWP10T
WARNING: If the information in this manual is not fol-
lowed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediatelycallyourgassupplierfromaneighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
—
Installation and service must be performed by a quali-
fied installer, service agency or the gas supplier.
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
Due to high temperatures, the
applianceshouldbelocatedout
oftrafficandawayfromfurniture
and draperies.
WARNING: This product
contains and/or generates
chemicals known to the State
of California to cause cancer or
birth defects or other reproduc-
tive harm.
Do not place clothing or other
flammable material on or near
the appliance. Never place any
objects on the heater.
IMPORTANT: Read this owner’s
manualcarefullyandcompletely
before trying to assemble,
operate or service this heater.
Improper use of this heater can
cause serious injury or death
from burns, fire, explosion,
electrical shock and carbon
monoxide poisoning.
Surface of heater becomes very
hot when running heater. Keep
children and adults away from
hot surface to avoid burns or
clothing ignition. Heater will
remain hot for a time after shut-
down. Allow surface to cool
before touching.
DANGER:Carbonmonoxide
poisoning may lead to death!
Carefully supervise young chil-
dren when they are in the same
room with heater.
Carbon Monoxide Poisoning: Early signs of
carbon monoxide poisoning resemble the flu, with
headaches, dizziness or nausea. If you have these
signs, the heater may not be working properly. Get
fresh air at once! Have heater serviced. Some
people are more affected by carbon monoxide
than others. These include pregnant women,
people with heart or lung disease or anemia,
those under the influence of alcohol and those at
high altitudes.
Make sure grill guard is in place
before running heater.
Keep the appliance area clear
and free from combustible ma-
terials, gasoline and other flam-
mable vapors and liquids.
Natural and Propane/LP Gas: Natural and Pro-
pane/LP gases are odorless. An odor-making
agent is added to these gases. The odor helps you
detect a gas leak. However, the odor added to the
gas can fade. Gas may be present even though no
odor exists.
1. This appliance is only for use with the type of
gas indicated on the rating plate. This appliance
is not convertible for use with other gases.
2. Do not place propane/LP supply tank(s) in-
side any structure. Locate propane/LP supply
tank(s) outdoors.
Make certain you read and understand all warn-
ings. Keep this manual for reference. It is your
guide to safe and proper operation of this heater.
3. Do not install 10,000 Btu/hr units in a bath-
room (6,000 Btu/hr heaters are allowed in a
bathroom).
WARNING: Any change to
this heater or its controls can
be dangerous.
4. If you smell gas
• Shut off gas supply
• Do not try to light any appliance
• Do not touch any electrical switch; do not
use any phone in your building
• Immediately call your gas supplier from a
neighborʼs phone. Follow the gas supplierʼs
instructions
WARNING: Do not use a
blower insert, heat exchanger
insertorotheraccessorynotap-
proved for use with this heater.
• If you cannot reach your gas supplier, call
the fire department
117001-01A
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
PRODUCT
Continued
IDENTIFICATION
5. This heater needs fresh, outside air ventilation
to run properly. This heater has an Oxygen
Depletion Sensing (ODS) safety shutoff
system. The ODS shuts down the heater if
not enough fresh air is available. See Air for
Combustion and Ventilation, page 5.
Control Knob
Ignitor Button
Grill
Guard
6. Keep all air openings in the front and bottom
of heater clear and free of debris. This will
insure enough air for proper combustion.
Glass
Panel
7. If heater shuts off, do not relight until you
provide fresh, outside air. If heater keeps
shutting off, have it serviced.
Heater
Cabinet
Front
Panel
8. Do not run heater
• where flammable liquids or vapors are used
or stored
• under dusty conditions
Figure 1 - Vent-Free Gas Heater
UNPACKING
9. Do not use heater if any part has been under
water. Immediately call a qualified service
technician to inspect the room heater and to
replace any part of the control system and any
gas control which has been under water.
1. Remove heater from carton.
2. Remove all protective packaging applied to
heater for shipment.
3. Check heater for any shipping damage. If
heater is damaged, promptly return to where
you bought heater.
10. Turn off heater and let cool before servicing.
Only a qualified service person should service
and repair heater.
PRODUCT FEATURES
SAFETY DEVICE
11. Operating heater above elevations of 4,500
feet (1,371 m) could cause pilot outage.
12. To prevent performance problems, do not use This heater has a pilot with an Oxygen Deple-
propane/LP fuel tank of less than 100 lbs.
(45 kg) capacity.
tion Sensing (ODS) safety shutoff system. The
ODS/pilot is a required feature for vent-free room
heaters. The ODS/pilot shuts off the heater if there
is not enough fresh air.
13. Before using furniture polish, wax, carpet
cleaner or similar products, turn heater off. If
heated, the vapors from these products may
create a white powder residue within burner
box or on adjacent walls or furniture.
PIEZO IGNITION SYSTEM
This heater has a piezo ignitor. This system re-
quires no matches, batteries or other sources to
light heater.
14. Provide adequate clearances around air
openings.
THERMOSTATIC HEAT CONTROL
(Thermostat Models Only)
Thermostat models have a thermostat sensing
bulb and a control valve. This results in the great-
est heater comfort. This can also result in lower
gas bills.
LOCAL CODES
Install and use heater with care. Follow all local
codes. In the absence of local codes, use the lat-
est edition of The National Fuel Gas Code, ANSI
Z223.1/NFPA 54*.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
4
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unusually Tight Construction
AIR FOR COMBUSTION
AND VENTILATION
The air that leaks around doors and windows
may provide enough fresh air for combustion and
ventilation. However, in buildings of unusually
tight construction, you must provide additional
fresh air.
WARNING: This heater shall
not be installed in a confined
space or unusually tight con-
struction unless provisions are
provided for adequate combus-
tionandventilationair. Readthe
following instructions to insure
proper fresh air for this and
other fuel-burning appliances
in your home.
Unusually tight construction is defined as
construction where:
a. walls and ceilings exposed to the out-
side atmosphere have a continuous
water vapor retarder with a rating of
one perm (6 x 10-11 kg per pa-sec-m2) or
less with openings gasketed or sealed
and
b. weather stripping has been added on
openable windows and doors and
Todayʼs homes are built more energy efficient
than ever. New materials, increased insulation and
new construction methods help reduce heat loss
in homes. Home owners weather strip and caulk
around windows and doors to keep the cold air out
and the warm air in. During heating months, home
owners want their homes as airtight as possible.
c. caulking or sealants are applied to
areas such as joints around window
and door frames, between sole plates
and floors, between wall-ceiling joints,
between wall panels, at penetrations
for plumbing, electrical and gas lines
and at other openings.
While it is good to make your home energy effi-
cient, your home needs to breathe. Fresh air must
enter your home.All fuel-burning appliances need
fresh air for proper combustion and ventilation.
If your home meets all of these three cri-
teria, you must provide additional fresh
air. See Ventilation Air From Outdoors,
page 7.
Exhaust fans, fireplaces, clothes dryers and fuel
burning appliances draw air from the house to
operate. You must provide adequate fresh air for
these appliances. This will insure proper venting
of vented fuel-burning appliances.
If your home does not meet all of the
three criteria above, proceed to Determin-
ing Fresh-Air Flow For Heater Location,
page 6.
Confined and Unconfined Space
PROVIDING ADEQUATE
VENTILATION
The following are excerpts from National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Section 5.3,
Air for Combustion and Ventilation.
The National Fuel Gas Code, ANSI Z223.1/NFPA
54 defines a confined space as a space whose
volume is less than 50 cubic feet per 1,000 Btu
per hour (4.8 m3 per kw) of the aggregate input
rating of all appliances installed in that space and
an unconfined space as a space whose volume is
not less than 50 cubic feet per 1,000 Btu per hour
(4.8 m3 per kw) of the aggregate input rating of
all appliances installed in that space. Rooms com-
municating directly with the space in which the
appliances are installed*, through openings not
furnished with doors, are considered a part of the
unconfined space.
All spaces in homes fall into one of the three fol-
lowing ventilation classifications:
1. Unusually Tight Construction
2. Unconfined Space
3. Confined Space
The information on pages 5 through 7 will help
you classify your space and provide adequate
ventilation.
* Adjoining rooms are communicating only if
there are doorless passageways or ventilation grills
between them.
117001-01A
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The space in the above example is a confined space
because the actual Btu/Hr used is more than the maxi-
mum Btu/Hr the space can support. You must provide
additional fresh air. Your options are as follows:
AIR FOR COMBUSTION
AND VENTILATION
Continued
A. Rework worksheet, adding the space of an
adjoining room. If the extra space provides an
unconfined space, remove door to adjoining
room or add ventilation grills between rooms.
See Ventilation Air From Inside Building.
DETERMINING FRESH-AIR FLOW
FOR HEATER LOCATION
Determining if You Have a Confined or
Unconfined Space
Use this work sheet to determine if you have a
B. Vent room directly to the outdoors. See Ventila-
tion Air From Outdoors, page 7.
confined or unconfined space.
C. Install a lower Btu/Hr heater, if lower Btu/Hr size
makes room unconfined.
Space: Includes the room in which you will install
heater plus any adjoining rooms with doorless pas-
sageways or ventilation grills between the rooms.
If the actual Btu/Hr used is less than the maximum
Btu/Hr the space can support, the space is an un-
confined space. You will need no additional fresh
air ventilation.
1. Determine the volume of the space (length x
width x height).
Length x Width x Height =__________cu. ft.
(volume of space)
Example: Space size 20 ft. (6.1 m) (length) x 16
ft. (4.88 m) (width) x 8 ft. (2.44 m) (ceiling height)
= 2560 cu. ft. (72.49 m3) (volume of space)
WARNING: If the area in
which the heater may be oper-
ated is smaller than that defined
as an unconfined space or if the
building is of unusually tight
construction, provide adequate
combustion and ventilation air
byoneofthemethodsdescribed
in the National Fuel Gas Code,
ANSIZ223.1/NFPA54Section5.3
or applicable local codes.
If additional ventilation to adjoining room is
supplied with grills or openings, add the volume
of these rooms to the total volume of the space.
2. Multiply the space volume by 20 to determine
the maximum Btu/Hr the space can support.
__________ (volume of space) x 20 = (Maxi-
mum Btu/Hr the space can support)
Example: 2,560 cu. ft. (72.49 m3) (volume of
space) x 20 = 51,200 (maximum Btu/Hr the space
can support)
3. Add the Btu/Hr of all fuel burning appliances in
the space.
VENTILATION AIR
Vent-free heater
Gas water heater*
Gas furnace
___________ Btu/Hr
___________ Btu/Hr
___________ Btu/Hr
___________ Btu/Hr
___________ Btu/Hr
Ventilation Air From Inside Building
This fresh air would come from an adjoining
unconfined space. When ventilating to an adjoin-
ing unconfined space, you must provide two
permanent openings: one within 12" (30.5 cm)
of the ceiling and one within 12" (30.5 cm) of the
floor on the wall connecting the two spaces (see
options 1 and 2, Figure 2, page 7). You can also
remove door into adjoining room (see option 3,
Figure 2, page 7). Follow the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for
Combustion and Ventilation for required size of
ventilation grills or ducts.
Vented gas heater
Gas fireplace logs
Other gas appliances* + __________ Btu/Hr
Total = __________ Btu/Hr
* Do not include direct-vent gas appliances. Di-
rect-vent draws combustion air from the outdoors
and vents to the outdoors.
Example:
50,000
___________ Btu/Hr
10,000
+ __________ Btu/Hr
60,000
= __________ Btu/Hr
Gas water heater
Vent-free heater
Total
4. Compare the maximum Btu/Hr the space can
support with the actual amount of Btu/Hr used.
__________Btu/Hr (maximum the space can support)
__________Btu/Hr (actual amount of Btu/Hr used)
Example: 51,200 Btu/Hr (maximum the space
can support)
60,000 Btu/Hr (actual amount of
Btu/Hr used)
6
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
AIR FOR COMBUSTION
INSTALLATION
AND VENTILATION
NOTICE:Thisheaterisintended
for use as supplemental heat.
Use this heater along with your
primary heating system. Do not
install this heater as your pri-
mary heat source. If you have a
centralheatingsystem,youmay
run system’s circulating blower
whileusingheater.Thiswillhelp
circulatetheheatthroughoutthe
house. In the event of a power
outage, you can use this heater
as your primary heat source.
Continued
12"
Ventilation Grills
Into Adjoining Room,
Ventilation
Option 2
Grills
into Adjoining
Room,
Or
Remove
Door into
Adjoining
Room,
Option 1
Option 3
12"
WARNING: A qualified ser-
vice person must install heater.
Follow all local codes.
CHECK GAS TYPE
Figure 2 - Ventilation Air from Inside
Building
Use only the correct type of gas (natural or pro-
pane/LP). If your gas supply is not the correct gas
type, do not install heater. Call dealer where you
bought heater for proper type heater.
Ventilation Air From Outdoors
Provide extra fresh air by using ventilation grills
or ducts. You must provide two permanent open-
ings: one within 12" (30.5 cm) of the ceiling and
one within 12" (30.5 cm) of the floor. Connect
these items directly to the outdoors or spaces
open to the outdoors. These spaces include attics
and crawl spaces. Follow the National Fuel Gas
Code, ANSI Z223.1/NFPA 54, Section 5.3, Air for
Combustion and Ventilation for required size of
ventilation grills or ducts.
WARNING: This appliance
is equipped for (natural or pro-
pane/LP) gas. Field conversion
is not permitted.
INSTALLATION ITEMS
Before installing heater, make sure you have the
items listed below.
IMPORTANT: Do not provide openings for inlet
or outlet air into attic if attic has a thermostat-
controlled power vent. Heated air entering the attic
will activate the power vent.
•
for propane/LPgas, external regulator (supplied
by installer)
•
•
•
•
•
•
•
•
piping (check local codes)
sealant (resistant to propane/LP gas)
equipment shutoff valve *
ground joint union
Ventilated
Outlet
Attic
Air
Outlet
sediment trap
Air
To Attic
tee joint
pipe wrench
To
Crawl
Space
for natural gas, test gauge connection*
* ACSAdesign-certified equipment shutoff valve
with 1/8" NPT tap is an acceptable alternative to
test gauge connection. The optional CSA design-
certified equipment shutoff valve can be purchased
from your dealer. See Accessories, page 25.
Inlet
Air
Ventilated
Crawl Space
Inlet Air
Figure 3 - Ventilation Air from Outdoors
117001-01A
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
CAUTION: If you install the
heater in a home garage
• heater pilot and burner must
be at least 18" (45.7 cm) above
floor
Continued
LOCATING HEATER
This heater is designed to be mounted on a wall.
WARNING: Maintain the
minimum clearances shown
in Figure 4. If you can, provide
greater clearances from floor,
ceiling and joining wall.
• locate heater where moving
vehicle will not hit it
CAUTION: This heater cre-
ates warm air currents. These
currents move heat to wall sur-
faces next to heater. Installing
heater next to vinyl or cloth wall
coverings or operating heater
where impurities (such as, but
not limited to, tobacco smoke,
aromatic candles, cleaning flu-
ids,oilorkerosenelamps,etc.)in
the air exist, may discolor walls
or cause odors.
WARNING: Never install the
heater
• in a bathroom (10,000 Btu/hr
only. 6,000 Btu/hr models are
allowed in a bathroom. Check
local codes.)
• in a recreational vehicle
• where curtains, furniture,
clothing or other flammable
objects are less than 36"
(91.5 cm) from the front, top
or sides of the heater
IMPORTANT: Vent-free heaters add moisture to
the air.Although this is beneficial, installing heater
in rooms without enough ventilation air may cause
mildew to form from too much moisture. See Air
for Combustion and Ventilation, page 5. If high hu-
midity is experienced, a dehumidifier may be used
to help lower the water vapor content in the air.
• as a fireplace insert
• in high traffic areas
• in windy or drafty areas
CEILING
For convenience and efficiency, install heater
•
where there is easy access for operation, inspec-
tion and service
36" (91.5 cm)
6"
Minimum
(15.3 cm)
•
in coldest part of room
Minimum
From
Sides Of
Heater
THERMOSTAT SENSING BULB
(Thermostat Models Only)
The thermostat sensing bulb is located inside the
heater. Do not move this bulb during installation
or operation of the heater.
Right
Side
Left
Side
INSTALLING HEATER TO WALL
Marking Screw Locations
1. Determine where you will locate heater.
3" (7.7 cm)
Minimum To Top Surface
Of Carpeting, Tile Or Other
Combustible Material
WARNING: Maintain mini-
mumclearancesshowninFigure
5, page 9. If you can, provide
greater clearances from floor
and joining wall.
Figure 4 - Mounting Clearances As
Viewed From Front of Heater
2. Mark two mounting screw locations on wall
(see Figure 5, page 9).
8
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
Thin or
INSTALLATION
Thick Wall
(thick wall
shown)
Continued
7
3
8
4
8 / "
7 / "
(22.5 cm)
Minimum To
Maintain 6"
(15.3 cm)
Clearance
From Wall
(14.7 cm)
1/16"
(1.6 mm)
Space
1
4
20 / "
Solid
Wall
(51.4 cm)
Minimum To
Maintain 3"
(7.7 cm)
Mounting
Screw
Locations
Figure 8 - Tightening Anchors
Placing Heater On Mounting Screws
1. Locate two keyhole slots on back panel of
heater (see Figure 9).
Clearance
From Floor
2. Place large openings of slots over screwheads.
Slide heater down until screws are in small
portion of slots.
FLOOR
Figure 5 - Mounting Screw Locations
Installing Two Mounting Screws
Note: Wall anchors and mounting screws are
in hardware package. The hardware package is
provided with heater.
Keyhole Slots
Attaching to wall stud method
For attaching mounting screw to wall stud
1. Drill hole at marked location using 9/64"
drill bit.
Figure 9 - Location Of Keyhole Slots On
Back Panel Of Heater
2. Insert mounting screw into wall stud.
Removing Front Panel Of Heater
1. Remove two screws near bottom corners of
front panel. See Figure 10.
3. Tightenscrewuntil1/16"(1.6mm)space(thick-
ness of penny) is between screwhead and wall.
Attaching to wall anchor method
2. Lift straight up on grill guard until it stops. Grill
guard will slide up about 1/4" (6.4 mm).
Follow instructions below to attach mounting
screws to hollow walls (wall areas between studs)
or solid walls (concrete or masonry).
3. Pull bottom of front panel forward, then
down.
1. Drill holes at marked locations using 5/16"
drill bit. For solid walls (concrete or masonry),
drill at least 1 1/4" (3.2 cm) deep.
2. Fold wall anchor (see Figure 6).
3. Insert wall anchor (wings first) into hole. Tap
anchor flush to wall.
4. For thin walls [1/2" (1.3 cm) or less], insert red
key into wall anchor. Push red key to “pop”
open anchor wings (see Figure 7).
IMPORTANT: Do not hammer key! For thick
walls [over 1/2" (1.3 cm) thick] or solid walls,
do not pop open wings.
5. Tighten two screws until 1/16" (1.6 mm) space
(thickness of penny) is between screwheads
and wall (see Figure 8).
Figure 10 - Removing Front Panel Of
Heater
Figure 6 - Folding
Anchor
Figure 7 - Popping
Open Anchor Wings
For Thin Walls
117001-01A
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
WARNING: For natural
gas, never connect heater to
private (non-utility) gas wells.
This gas is commonly known
as wellhead gas.
Continued
Installing Bottom Mounting Screw
1. Locate bottom mounting hole. This hole is
near bottom on back panel of heater (see
Figure 11).
2. Mark screw location on wall.
3. Remove heater from wall.
IMPORTANT: For natural gas, check gas line
pressure before connecting heater to gas line. Gas
line pressure must be no greater than 10.5 inches of
water. If gas line pressure is higher, heater regula-
tor damage could occur.
4. If installing bottom mounting screw into hol-
low or solid wall, install wall anchor. Follow
steps 1 through 5 under Attaching To Wall
Anchor Method, page 9. If installing bottom
mounting screw into wall stud, drill hole at
marked location using 9/64" drill bit.
CAUTION: For propane/LP
gas, never connect heater di-
rectly to the propane/LP supply.
This heater requires an external
regulator (not supplied). Install
theexternalregulatorbetweenthe
heater and propane/LP supply.
5. Replace heater on wall.
6. Insert bottom anchor screw through back
panel into bottom anchor or drilled hole (see
Figure 11).
7. Tighten screw until heater is firmly secured to
wall. Do not over tighten.
Note: Do not replace front panel at this time.
Replace front panel after making gas connec-
tions and checking for leaks (see pages 10
through 12).
For propane/LP gas, the installer must supply an
external regulator. The external regulator will
reduce incoming gas pressure. You must reduce
incoming gas pressure to between 11 and 14 inches
of water. If you do not reduce incoming gas pres-
sure, heater regulator damage could occur. Install
the external regulator with the vent pointing down
as shown in Figure 12. Pointing the vent down
protects it from freezing rain or sleet.
CAUTION: Use only new,
black iron or steel pipe. Inter-
nally-tinned copper tubing may
be used in certain areas. Check
your local codes. Use pipe of
large enough diameter to allow
proper gas volume to heater. If
pipe is too small, undue loss of
volume will occur.
Figure 11 - Installing Bottom Mounting
Screw
CONNECTING TO GAS SUPPLY
WARNING: This appliance
requires a 3/8" NPT (National
PipeThread)inletconnectionto
the pressure regulator.
Propane/LP
External
Supply Tank
Regulator
WARNING: A qualified ser-
vicepersonmustconnectheater
to gas supply. Follow all local
codes.
Vent
Pointing
Down
Figure 12 - External Regulator With Vent
Pointing Down (Propane/LP only)
10
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Hold the pressure regulator with
wrench when connecting it to gas piping and/or
fittings. Do not over tighten pipe connection to
regulator. The regulator body could be damaged.
INSTALLATION
Continued
Installation must include equipment shutoff valve,
union and plugged 1/8" NPT tap. Locate NPT tap
within reach for test gauge hook up. NPT tap must
be upstream from heater (see Figure 13).
CHECKING GAS CONNECTIONS
WARNING:Testallgaspiping
and connections, internal and
external to unit, for leaks after
installing or servicing. Correct
all leaks at once.
IMPORTANT: Install an equipment shutoff valve
in an accessible location. The equipment shutoff
valve is for turning on or shutting off the gas to
the appliance.
Apply pipe joint sealant lightly to male NPT
threads. This will prevent excess sealant from
going into pipe. Excess sealant in pipe could result
in clogged heater valves.
WARNING: Never use an
open flame to check for a leak.
Applyanoncorrosiveleakdetec-
tion fluid to all joints. Bubbles
forming show a leak. Correct all
leaks at once.
WARNING: Use pipe joint
sealant that is resistant to liquid
petroleum (LP) gas.
Install sediment trap in supply line as shown in
Figure 13. Locate sediment trap where it is within
reach for cleaning. Locate sediment trap where
trapped matter is not likely to freeze. A sediment
trap traps moisture and contaminants. This keeps
them from going into heater controls. If sediment
trap is not installed or is installed wrong, heater
may not run properly.
CAUTION: For propane/LP
gas, make sure external regula-
tor has been installed between
propane/LP supply and heater.
See guidelines under Connect-
ing to Gas Supply, page 10.
3/8" NPT
Pipe
Nipple
PRESSURE TESTING GAS SUPPLY
PIPING SYSTEM
Pressure
Regulator
Test Pressures In Excess Of 1/2 PSIG
(3.5 kPa)
Ground
Joint
Union
1. Disconnect appliance with its appliance main
gas valve (control valve) and equipment
shutoff valve from gas supply piping system.
Pressures in excess of 1/2 psig will damage
heater regulator.
Heater
Cabinet
Equipment
Shutoff
Valve *
Tee Joint
Reducer
Bushing to
1/8" NPT
2. Cap off open end of gas pipe where equipment
shutoff valve was connected.
Natural Gas
From Gas
Meter (7" W.C.
to 10.5" W.C.
Pressure)
Propane/LP
From External
Regulator
(11" W.C. to 14"
W.C. Pressure)
1/8" NPT
Plug Tap
3. Pressurize supply piping system by either
opening propane/LP supply tank valve for
propane/LP gas or opening main gas valve
located on or near gas meter for natural gas
or using compressed air.
3"
Min.
4. Check all joints of gas supply piping system.
Apply a noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak.
Cap Pipe Tee
Nipple Joint
Sediment Trap
5. Correct all leaks at once.
Figure 13 - Gas Connection
6. Reconnect heater and equipment shutoff
valve to gas supply. Check reconnected fit-
tings for leaks.
* ACSAdesign-certified equipment shutoff valve
with 1/8" NPT tap is an acceptable alternative to
test gauge connection. Purchase the optional CSA
design-certified equipment shutoff valve from your
dealer. See Accessories, page 25.
117001-01A
11
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Make sure control knob of heater is in the OFF
position.
INSTALLATION
Continued
4. Check all joints from equipment shutoff valve
to thermostat gas valve (see Figure 15 or 16).
Apply a noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak.
Test Pressures Equal To or Less Than
1/2 PSIG (3.5 kPa)
1. Close equipment shutoff valve (see Figure 14).
2. Pressurize supply piping system by either
opening propane/LP supply tank valve for
propane/LP gas or opening main gas valve
located on or near gas meter for natural gas
or using compressed air.
5. Correct all leaks at once.
6. Light heater (see Operating Heater). Check
all other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas to Appli-
ance, page 13).
3. Check all joints from gas meter for natural gas
(see Figure 15) or propane/LP supply tank for 8. Replace front panel.
propane/LP gas, to equipment shutoff valve
OPERATING HEATER
FOR YOUR SAFETY READ
(see Figure 16). Apply a noncorrosive leak
detection fluid to all joints. Bubbles forming
show a leak.
BEFORE LIGHTING
4. Correct all leaks at once.
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see Figure 14).
WARNING: If you do not fol-
low these instructions exactly,
a fire or explosion may result
causing property damage, per-
sonal injury or loss of life.
2. For natural gas open main gas valve located
on or near gas meter. For propane/LPgas open
propane/LP supply tank valve.
Open
Equipment
Shutoff Valve
A. This appliance has a pilot which must be
lighted by hand. When lighting the pilot,
follow these instructions exactly.
B. BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than
air and will settle on the floor.
Closed
Figure 14 - Equipment Shutoff Valve
WHAT TO DO IF YOU SMELL GAS
Control
Valve
Location
• Do not try to light any appliance.
• Do not touch any electric switch; do not
use any phone in your building.
Gas
Meter
• Immediately call your gas supplier from
a neighborʼs phone. Follow the gas
supplierʼs instructions.
Equipment
Shutoff
Valve
• If you cannot reach your gas supplier, call
the fire department.
C. Use only your hand to push in or turn the
gas control knob. Never use tools. If the
knob will not push in or turn by hand,
donʼt try to repair it, call a qualified service
technician. Force or attempted repair may
result in a fire or explosion.
Figure 15 - Checking Gas Joints for
Natural Gas
Propane/LP
Supply Tank
Control
Valve
Location
D. Do not use this appliance if any part has
been under water. Immediately call a
qualified service technician to inspect the
appliance and to replace any part of the
control system and any gas control which
has been under water.
Equipment
Shutoff
Valve
Figure 16 - Checking Gas Joints for
Propane/LP Gas
12
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING HEATER
WARNING: Always operate
manual control heaters at the
locked positions. Operation
between these positions may
create a possible health hazard
if used in a poorly ventilated
room. Read owner’s manual for
complete instructions.
Continued
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information, page 12.
2. Make sure equipment shutoff valve is fully
open.
3. Turn off any electric power to the appliance
if service is to be performed.
4. Turn control knob clockwise
OFF position.
to the
CAUTION: Do not try to ad-
just heating levels by using the
equipment shutoff valve.
5. Wait five minutes to clear out any gas. Then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety
information, page 12. If you donʼt smell gas,
go to the next step.
Control
Ignitor Button
Knob
6. Thermostat Models: Turn control knob
counterclockwise
to the PILOT
position. Press in control knob for five (5)
seconds.
Figure 17 - Control Knob In The OFF
Position for Manual Control Models
Manual Models: Press in and turn control
knob counterclockwise
to the PILOT
Ignitor
Button
position. Keep control knob pressed in for
five (5) seconds.
Control
Knob
T
O
L
I
P
F
F
O
7. With control knob pressed in, push down
and release ignitor button. This will light
pilot. The pilot is attached to the front of
burner. Note: You may be running this
heater for the first time after hooking up to
gas supply. If so, you may need to press in
control knob for 30 seconds or more. This
will allow air to bleed from the gas system.
If needed, keep pressing ignitorbutton until
pilot lights. If ignitor does not light pilot,
refer to Troubleshooting, page 16 or contact
a qualified service person orgas supplierfor
repairs. Until repairs are made, light pilot
with match. To light pilot with match, see
Manual Lighting Procedure, page 14.
Figure 18 - Control Knob In The OFF
Position for Thermostat Models
Ignitor Electrode
Thermocouple
Pilot
Burner
Figure 19 - Pilot
8. Keep control knob pressed in for30 seconds
after lighting pilot.After 30 seconds, release
control knob.
TO TURN OFF GAS
TO APPLIANCE
• If control knob does not pop up when Shutting Off Heater
released, contact a qualified service person 1. Turn control knob clockwise
to the
or gas supplier for repairs.
OFF position.
Note: If pilot goes out, repeat steps 4 thru 7.
Thermostat models have a safety interlock
system. Wait one (1) minute before lighting
pilot again.
2. Turn off all electric power to the appliance
if service is to be performed.
Shutting Off Burner Only (pilot stays lit)
Turn control knob clockwise
to the
9. Turn control knob counterclockwise
to desired heating level. The main burner
should light. Manual control heaters should
be used in locked positions.
PILOT position.
117001-01A
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The pilot flame on natural gas units will
have a slight curve, but flame should be blue and
have no yellow or orange color.
OPERATING HEATER
Continued
THERMOSTAT CONTROL
OPERATION
Blue Flame
Pilot Burner
The thermostatic control used on these models
differs from standard thermostats. Standard
thermostats simply turn on and off the burner.
The thermostat used on this heater senses the
room temperature. At times the room may
exceed the set temperature. If so, the burner
will shut off. The burner will cycle back on
when room temperature drops below the set
temperature. The control knob can be set to
any heat level between 1 and 5. This adjusts the
amount of gas flow to the burner that increases
or decreases the burner flame height.
Thermocouple
Figure 20 - Correct Pilot Flame Pattern
Yellow Flame
Pilot Burner
Thermocouple
Note: The thermostat sensing bulb measures
the temperature of air near the heater cabinet.
This may not always agree with room tem-
perature (depending on housing construction,
installation location, room size, open air tem-
peratures, etc.) Frequent use of your heater will
let you determine your own comfort levels.
Figure 21 - Incorrect Pilot Flame Pattern
BURNER FLAME PATTERN
Figure 22, page 15, shows a correct burner flame
pattern. Figure 23, page 15, shows an incorrect
burnerflamepattern.Theincorrectburnerflamepat-
ternshowsyellowtippingoftheflame. Italsoshows
the flame higher than 1/2 the glass panel height.
MANUAL LIGHTING
PROCEDURE
1. Remove front panel (see Figure 10, page 9).
2. Follow steps 1 through 7 under Lighting
Instructions, page 13.
WARNING: If yellow tipping
occurs, your heater could pro-
duce increased levels of car-
bon monoxide. If burner flame
pattern shows yellow tipping,
proceed with the following in-
structions.
3. With control knob pressed in, strike match.
Hold match to pilot until pilot lights.
4. Keep control knob pressed in for30 seconds
after lighting pilot.After 30 seconds, release
control knob. Now follow step 9, under
Lighting Instructions, page 13.
5. Replace front panel.
NOTICE: Do not mistake orange
flames with yellow tipping. Dust
or other fine particles enter the
heater and burn causing brief
patches of orange flame.
INSPECTING HEATER
Check pilot flame pattern and burner flame pat-
tern often.
PILOT FLAME PATTERN
Figure 20 shows a correct pilot flame pattern.
Figure 21 shows an incorrect pilot flame pattern.
The incorrect pilot flame is not touching the
thermocouple. This will cause the thermocouple
to cool. When the thermocouple cools, the heater
will shut down.
If burner flame pattern is incorrect, as shown in
Figure 23, page 15,
•
turn heater off (see To Turn Off Gas to Appli-
ance, page 13)
•
see Troubleshooting, page 16
If pilot flame pattern is incorrect, as shown in
Figure 21
•
turn heater off (see To Turn Off Gas to Appli-
ance, page 13)
•
see Troubleshooting, page 16
14
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
BURNER PILOT AIR INLET
INSPECTING HEATER
The primary air inlet holes allow the proper
amount of air to mix with the gas. This provides a
clean burning flame. Keep these holes clear of dust,
dirt and lint. Clean these air inlet holes prior to each
heating season. Blocked air holes will create soot.
We recommend that you clean the unit every three
months during operation and have heater inspected
yearly by a qualified service person.
Continued
1/2 GLASS HEIGHT
(Models GWN6 and GWP6 will be lower due to
lower input rating)
We also recommend that you keep the burner
tube and pilot assembly clean and free of dust and
dirt. To clean these parts we recommend using
compressed air no greater than 30 PSI. Your local
computer store, hardware store or home center
may carry compressed air in a can. You can use a
vacuum cleaner in the blow position. If using com-
pressed air in a can, please follow the directions on
the can. If you don't follow directions on the can,
you could damage the pilot assembly.
Figure 22 - Correct Burner Flame Pattern
Yellow
Tipping
1/2 GLASS HEIGHT
Figure 23 - Incorrect Burner Flame
Pattern
1. Shut off the unit, including the pilot. Allow
the unit to cool for at least thirty minutes.
2. Inspect burner, pilot for dust and dirt.
CLEANING AND
MAINTENANCE
3. Blow air through the ports/slots and holes in
the burner.
4. Never insert objects into the pilot tube.
WARNING: Turn off heater
and let cool before cleaning.
Clean the pilot assembly also. A yellow tip on the
pilot flame indicates dust and dirt in the pilot as-
sembly. There is a small pilot air inlet about two
inches from where the pilot flame comes out of
the pilot assembly (see Figure 24). With the unit
off, lightly blow air through the air inlet. You may
blow through a drinking straw if compressed air
is not available.
CAUTION: You must keep
control areas, burner and circu-
latingairpassagewaysofheater
clean. Inspect these areas of
heater before each use. Have
heater inspected yearly by a
qualifiedserviceperson. Heater
may need more frequent clean-
ing due to excessive lint from
carpeting, beddingmaterial, pet
hair, etc.
Pilot Assembly
Pilot Air Inlet
Figure 24 - Pilot Air Inlet Hole
CABINET
WARNING: Failure to keep
the primary air opening(s) of
theburner(s)cleanmayresultin
sooting and property damage.
Air Passageways
Use a vacuum cleaner or pressurized air to
clean.
ODS/PILOT AND BURNER
Use a vacuum cleaner, pressurized air or small,
soft bristled brush to clean.
Exterior
Use a soft cloth dampened with a mild soap and
water mixture. Wipe the cabinet to remove dust.
117001-01A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
WARNING:Turnoffandunplugheaterandletcoolbeforeservicing.
Only a qualified service person should service and repair heater.
CAUTION: Never use a wire, needle or similar object to clean
ODS/pilot. This can damage ODS/pilot unit.
Note: All troubleshooting items are listed in order of operation.
OBSERVED PROBLEM POSSIBLE CAUSE
REMEDY
When ignitor button is pressed 1. Ignitor electrode positioned 1. Replace pilot assembly
in, there is no spark at ODS/
pilot
wrong
2. Ignitor electrode broken
2. Replace pilot assembly
3. Ignitor electrode not connected 3. Reconnect ignitor cable
to ignitor cable
4. Ignitor cable pinched or wet
4. Free ignitor cable if pinched
by any metal or tubing. Keep
ignitor cable dry
5. Broken ignitor cable
6. Bad piezo ignitor
7. Piezo ignitor nut is loose
5. Replace ignitor cable
6. Replace piezo
7. Tighten nut holding piezo
ignitor. Nut is located inside
heater cabinet at top
When ignitor button is pressed 1. Gas supply turned off or equip- 1. Turn on gas supply or open
in, there is a spark at ODS/Pilot
but no ignition
ment shutoff valve closed
2. Control knob not in PILOT 2. Turn control knob to PILOT
position position
3. Control knob not pressed in 3. Press in control knob while in
while in PILOT position PILOT position
4. Air in gas lines when in- 4. Continue holding down con-
equipment shutoff valve
stalled
trol knob. Repeat igniting
operation until air is removed
5. Depleted gas supply (propane/ 5. Contact local propane/LP gas
LP only)
6. ODS/pilot is clogged
company
6. Clean ODS/pilot (see Cleaning
and Maintenance, page 15) or
replace ODS/pilot assembly
7. Gas regulator setting is not 7. Replace gas regulator
correct
16
Download from Www.Somanuals.com. All Manuals Search And Download.
117001-01A
TROUBLESHOOTING
Continued
OBSERVED PROBLEM POSSIBLE CAUSE
REMEDY
ODS/pilot lights but flame 1. Control knob not fully pressed in 1. Press in control knob fully
goes out when control knob is 2. Control knob not pressed in 2. After ODS/pilot lights, keep
released
long enough
control knob pressed in 30
seconds
3. Equipment shutoff valve not 3. Fully open equipment shutoff
fully open valve
4. Thermocouple connection 4. Hand tighten until snug, then
loose at control valve tighten 1/4 turn more
5. Pilot flame not touching ther- 5. A) Contact local natural or
mocouple, which allows ther-
mocouple to cool, causing
pilot flame to go out. This
problem could be caused by
one or both of the following:
A)Low gas pressure
propane/LP gas company
B) Clean ODS/pilot (see
Cleaning and Maintenance,
page 15) or replace ODS/pilot
assembly
B)Dirty or partially clogged
ODS/pilot
6. Thermocouple damaged
7. Control valve damaged
6. Replace pilot assembly
7. Replace control valve
Burner does not light after 1. Burner orifice is clogged
ODS/pilot is lit
1. Cleanburnerorifice(seeClean-
ing and Maintenance, page 15)
or replace burner orifice
2. Inlet gas pressure is too low
2. Contact local natural or pro-
pane/LP gas company
Delayed ignition of burner
1. Manifold pressure is too low 1. Contact local natural or pro-
pane/LP gas company
2. Burner orifice is clogged
2. Cleanburnerorifice(seeClean-
ing and Maintenance, page 15)
or replace burner orifice
Burner backfiring during com- 1. Burner orifice is clogged or 1. Cleanburnerorifice(seeClean-
bustion
damaged
ing and Maintenance, page 15)
or replace burner orifice
2. Replace burner
2. Burner damaged
3. Gas regulator defective
3. Replace gas regulator
117001-01A
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
OBSERVED PROBLEM POSSIBLE CAUSE
REMEDY
Yellow flame during burner 1. Not enough air
combustion
1. Check burner for dirt and de-
bris. If found, clean burner (see
Cleaning and Maintenance,
page 15)
2. Inlet gas pressure is too low
3. Gas regulator defective
2. Contact local natural or pro-
pane/LP gas company
3. Replace gas regulator
Slight smoke or odor during 1. Residues from manufacturing 1. Problem will stop after a few
initial operation processes hours of operation
Heater produces a whistling 1. Turning control knob to high- 1. Turn control knob to lowest
noise when burner is lit
est position when burner is
cold
2. Air in gas line
position and let warm up for a
minute
2. Operate burner until air is
removed from line. Have gas
checked by local natural or
propane/LP gas company
3. Air passageways on heater 3. Observe minimum installation
blocked clearances (see Figure 4, page 8)
4. Dirty or partially clogged 4. Clean burner (see Cleaning
burner orifice
and Maintenance, page 15) or
replace burner orifice
Heaterproducesaclicking/tick- 1. Metal expanding while heating 1. Thisiscommonwithmostheat-
ing noise just after burner is lit
or shut off
or contracting while cooling
ers. Ifnoiseisexcessive, contact
qualified service person
White powder residue forming 1. When heated, vapors from 1. Turn heater off when using
withinburnerboxoronadjacent
walls or furniture
furniture polish, wax, carpet
cleaner, etc., may turn into
white powder residue
furniture polish, wax, carpet
cleaners or similar products
18
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
•
Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Fol-
low the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating heater where impurities in air exist may create odors. Cleaning supplies,
paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create fumes.
These fumes may mix with combustion air and create odors.
OBSERVED PROBLEM POSSIBLE CAUSE
REMEDY
Heater produces unwanted 1. Heater burning vapors from 1. Ventilate room. Stop using
odors
paint, hair spray, glues, etc. See
IMPORTANT statement above
2. Low fuel supply (propane/LP 2. Refill supply tank
odor causing products while
heater is running
gas only)
3. Gas leak. See Warning 3. Locate and correct all leaks
statement at top of page
(see Checking Gas Connec-
tions, page 11)
Heater shuts off in use (ODS 1. Not enough fresh air is avail- 1. Open window and/or door for
operates)
able
2. Low line pressure
ventilation
2. Contact local natural or pro-
pane/LP gas company
3. ODS/pilot is partially 3. CleanODS/pilot(seeCleaning
clogged and Maintenance, page 15)
Gas odor even when control 1. Gas leak. See Warning 1. Locate and correct all leaks
knob is in OFF position
statement at top of page
(see Checking Gas Connec-
tions, page 11)
2. Replace control valve
2. Control valve defective
Gas odor during combustion
1. Foreign matter between con- 1. Take apart gas tubing and
trol valve and burner remove foreign matter
2. Gas leak. See Warning 2. Locate and correct all leaks
statement at top of page
(see Checking Gas Connec-
tions, page 11)
Moisture/condensation noticed 1. Not enough combustion/ven- 1. Refer to Air for Combustion
on windows
tilation air
and Ventilation requirements
(page 5)
117001-01A
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS BREAKDOWN
MODELS GWP6, GWN6, GWP10 AND GWN10
21
22
20
23
24
19
13
12
10
15
11
9
4
10
14
17
18
8
7
6
16
5
3
2
11
11-1
1
ODS/Pilot
20
Download from Www.Somanuals.com. All Manuals Search And Download.
117001-01A
PARTS LIST
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions
listed under Replacement Parts on page 25 of this manual.
KEY
NO. PART NO.
DESCRIPTION
QTY
2
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
098304-01 Screw, #10 x 3/8"
099467-07 Front Panel
099318-04 Grill Guard
101108-01 Grill Guard Clip
102017-02 Bottom Glass Retainer
098260-11 Glass Panel
099319-02 Top Glass Retainer
099317-02 Deflector Unit
098271-09 Ignitor Cable
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10 098249-01 Nut, M5
11 110803-01* ODS/Pilot Assembly
110803-02* ODS/Pilot Assembly
11-1 110186-01 Thermocouple Kit
12 104263-03 Burner
•
•
•
•
•
•
•
•
•
104263-02 Burner
•
•
13 099387-17 Pilot Tubing
14 104259-01 Injector, 1 piece
104259-02 Injector, 1 piece
104259-03 Injector, 1 piece
104259-04 Injector, 1 piece
•
•
•
•
•
•
•
•
15 NJF-8C
Hex Nut
•
•
•
•
•
16 099415-17 Pressure Regulator
099415-18 Pressure Regulator
17 099462-01 Burner Tubing
18 099391-02 Regulator Tubing
19 099413-01 Control Valve
099413-02 Control Valve
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
20
**
Cabinet Assembly
•
•
•
•
•
•
•
•
•
•
21 097159-04 Piezo Ignitor
22 099393-02 Control Knob
23 098508-01 Valve Retainer Nut
24 099818-01 Internal Tooth Washer
PARTS AVAILABLE - NOT SHOWN
100642-02 Assembly, Hardware
** Not a field replaceable part.
•
•
•
•
1
* If replacing ODS pilot and your model is pre 2002, your part
number will be 100701-03 for natural gas models, 099059-03
for propane/LP models. The thermocouple part number will be
098514-01 for both gases. The electrode part number will be
098594-01 for both gases.
117001-01A
21
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS BREAKDOWN
MODELS GWP10T AND GWN10T
21
20
19
9
13
15
12
18
11
9
4
17
10
13
14
8
7
6
16
5
2
3
11
1
11-1
ODS/Pilot
22
Download from Www.Somanuals.com. All Manuals Search And Download.
117001-01A
PARTS LIST
This list contains replaceable parts used in your heater. When ordering parts, follow the instructions
listed under Replacement Parts on page 25 of this manual.
KEY
NO. PART NO.
DESCRIPTION
QTY.
2
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
098304-01 Screw, #10 x 3/8"
099467-07 Front Panel Assembly
099318-04 Grill Guard
101108-01 Grill Guard Clip
102017-02 Bottom Glass Retainer
098260-11 Glass Panel
099319-02 Top Glass Retainer
099317-02 Deflector Unit
098271-09 Ignitor Cable
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
10 098249-01 Nut, M5
11
110803-01* ODS/Pilot Assembly
110803-02* ODS/Pilot Assembly
•
•
•
•
11-1 110186-01 Thermocouple Kit
12 104263-03 Burner
13 099387-11 Pilot Tubing
14 104259-05 Injector, 1 Piece
104259-06 Injector, 1 Piece
15 NJF 8C
16 099415-17 Pressure Regulator
099415-18 Pressure Regulator
17 104261-01 Burner Tubing
18 104264-01 Regulator Tubing
19 098522-11 Thermostat Gas Valve
098522-18 Thermostat Gas Valve
•
•
•
•
•
•
Hex Nut
•
•
•
•
•
•
•
•
•
•
•
20
**
Cabinet Assembly
•
•
21 097159-04 Piezo Ignitor
PARTS AVAILABLE - NOT SHOWN
100642-02 Assembly, Hardware
** Not a field replaceable part.
•
•
1
* If replacing ODS pilot and your model is pre 2002, your
part number will be 100701-03 for natural gas models,
099059-03 for propane/LPmodels. The thermocouple part
number will be 098514-01 for both gases. The electrode
part number will be 098594-01 for both gases.
117001-01A
23
Download from Www.Somanuals.com. All Manuals Search And Download.
GWN10
SPECIFICATIONS
•
•
•
•
•
5,000/10,000 Btu/hr (Variable)
GWP6
Natural Gas
•
•
•
•
•
4,400/6,000 Btu/hr (Variable)
Piezo Ignition
Propane/LP Gas
Pressure Regulator Setting - 3" W.C.
Piezo Ignition
Inlet Gas Pressure (inches of water)
Maximum - 10.5", Minimum - 5"
Pressure Regulator Setting - 8" W.C.
Inlet Gas Pressure (inches of water)
Maximum - 14", Minimum - 11"
•
•
Heater Dimensions (H x W x D)
21.5" x 13.5" x 7" (54.6 x 34.3 x 17.8 cm)
•
•
Heater Dimensions (H x W x D)
21.5" x 13.5" x 7" (54.6 x 34.3 x 17.8 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
•
•
Heater Weight - 12.5 lb (5.7 kg)
Heater Shipping Weight - 14 lb (6.4 kg)
•
•
Heater Weight - 12.5 lb (5.7 kg)
GWP10T
Heater Shipping Weight - 14 lb (6.4 kg)
•
•
•
•
•
5,000/10,000 Btu/hr (Variable)
GWN6
Propane/LP Gas
•
•
•
•
•
4,400/6,000 Btu/hr (Variable)
Piezo Ignition
Natural Gas
Pressure Regulator Setting - 8" W.C.
Piezo Ignition
Inlet Gas Pressure (inches of water)
Maximum - 14", Minimum - 11"
Pressure Regulator Setting - 3" W.C.
Inlet Gas Pressure (inches of water)
Maximum - 10.5", Minimum - 4"
•
•
Heater Dimensions (H x W x D)
22" x 13.5" x 7" (55.9 x 34.3 x 17.8 cm)
•
•
Heater Dimensions (H x W x D)
21.5" x 13.5" x 7" (54.6 x 34.3 x 17.8 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
•
•
Heater Weight - 13.5 (6.1 kg)
Heater Shipping Weight - 15 lb (6.8 kg)
•
•
Heater Weight - 12.5 lb (5.7 kg)
GWN10T
Heater Shipping Weight - 14 lb (6.4 kg)
•
•
•
•
•
5,000/10,000 Btu/hr (Variable)
GWP10
Natural Gas
•
•
•
•
•
5,000/10,000 Btu/hr (Variable)
Piezo Ignition
Propane/LP Gas
Pressure Regulator Setting - 3" W.C.
Piezo Ignition
Inlet Gas Pressure (inches of water)
Maximum - 10.5", Minimum - 5"
Pressure Regulator Setting - 8" W.C.
Inlet Gas Pressure (inches of water)
Maximum - 14", Minimum - 11"
•
•
Heater Dimensions (H x W x D)
22" x 13.5" x 7" (55.9 x 34.3 x 17.8 cm)
•
•
Heater Dimensions (H x W x D)
21.5" x 13.5" x 7" (54.6 x 34.3 x 17.8 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
Carton Dimensions (H x W x D)
25" x 16.75" x 7.75" (63.5 x 42.5 x 19.7 cm)
•
•
Heater Weight - 13.5 (6.1 kg)
Heater Shipping Weight - 15 lb (6.8 kg)
•
•
Heater Weight - 12.5 lb (5.7 kg)
Heater Shipping Weight - 14 lb (6.4 kg)
24
117001-01A
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
REPLACEMENT PARTS
Purchase this heater accessory from your local Note: Use only original replacement parts. This
dealer. If they can not supply this accessory, either will protect your warranty coverage for parts
contact your nearest Parts Central (page 26) or replaced under warranty.
call DESA Heating Products at 1-866-672-6040 for
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If
referralinformation.Youcanalsowritetotheaddress
listed on the back page of this manual.
they canʼt supply original replacement part(s),
call DESA Heating Productsʼ Technical Service
Department at 1-866-672-6040.
When calling DESA Heating Products, have
ready
•
•
•
•
•
•
your name
your address
model and serial numbers of your heater
how heater was malfunctioning
type of gas used (propane/LP or natural gas)
purchase date
EQUIPMENT SHUTOFF VALVE
GA5010
For all models. Equipment shutoff valve with
Usually, we will ask you to return the part to the
factory.
1/8" NPT tap.
ELECTRONIC IGNITOR KIT - GA435
Not Shown
For all piezo ignitor models. Provides easier
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they
canʼt supply original replacement part(s), either
contact your nearest Parts Central (see page 26)
or call DESAHeating Products at 1-866-672-6040
for referral information.
lighting of the pilot.
SERVICE HINTS
When Gas Pressure Is Too Low
When calling DESA Heating Products, have
ready
•
•
•
•
pilot will not stay lit
•
•
model number of your heater
the replacement part number
burner will have delayed ignition
heater will not produce specified heat
propane/LP gas supply may be low
Youmayfeelyourgaspressureistoolow. Ifso, con-
tact your local natural or propane/LP gas supplier.
TECHNICAL SERVICE
You may have further questions about installation,
operation or troubleshooting. If so, contact DESA
Heating Productsʼ Technical Service Department
at 1-866-672-6040. When calling please have your
model and serial numbers of your heater ready.
You can also visit DESAHeating Productsʼtechni-
SERVICE PUBLICATIONS
Youcanpurchaseaservicemanualfromtheaddress
listed on the back page of this manual. Send a check
for $5.00 payable to DESA Heating Products.
117001-01A
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS CENTRAL
These Parts Centrals are privately owned businesses. They have agreed to support our customerʼs needs
by providing original replacement parts and accessories.
Tool & Equipment Co.
5 Manila Ave
Washer Equipment Co.
1715 Main Street
Hamden, CT 06514-0322
1-800-397-7553
203-248-7553
Kansas City, MO 64108-2195
KS, MO, AR
816-842-3911
Portable Heater Parts
342 N. County Rd. 400 East
Valparaiso, IN 46383-9704
219-462-7441
East Coast Energy
707 Broadway
W. Long Branch, NJ 07764-1501
732-870-8809
1-800-755-8809
1-888-619-7060
21st Century
FBD
2950 Fretz Valley
Perkasie, PA 18944-4034
215-795-0400
1349 Adams Street
Bowling Green, KY 42103-3414
270-846-1199
800-325-4828
1-800-654-8534
Fax: 1-800-846-0090
Laporte’s Parts & Service
2444 N. 5th Street
Hartsville, SC 29550-7704
843-332-0191
Parts Department
Master Parts Dist.
1251 Mound Ave. NW
Grand Rapids, MI 49504-2672
616-791-0505
1-800-446-1446
Cans Unlimited
P.O. Box 645
Taylor, SC 29687-0013
803-879-3009
1-800-845-5301
26
Download from Www.Somanuals.com. All Manuals Search And Download.
117001-01A
NOTES
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
_____________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
______________________________________________________
117001-01A
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our
standard written warranty. We make no other warranty, expressed or implied.
LIMITED WARRANTIES FOR NEW AND FACTORY
RECONDITIONED PRODUCTS
New Products: DESAHeating Products warrants this heater and any parts thereof, to be free of defects in materials
and workmanship for two (2) years from the date of first purchase, when operated and maintained in accordance
with the manufacturer's instructions. These warranties are extended only to the original retail purchaser, when
proof of purchase is provided.
Factory Reconditioned Heaters: DESAHeating Products warrants this factory reconditioned heater and any parts
thereof, to be free of defects in materials and workmanship for thirty (30) days from the date of first purchase,
when operated and maintained in accordance with the manufacturer's instructions. These warranties are extended
only to the original retail purchaser, when proof of purchase is provided.
This warranty is extended only to the original retail purchaser. This warranty covers only the cost of part(s) required
to restore this heater to proper operating condition. Warranty part(s) MUST be obtained through authorized dealers
of this product and/or DESA Heating Products who will provide original factory replacement parts. Failure to use
original factory replacement parts voids this warranty. The heater MUST be installed by a qualified installer in
accordance with all local codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear or parts
that fail or become damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by
improper installation. Travel, diagnostic cost, labor, transportation and any and all such other costs related to
repairing a defective heater will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE
OF THE PRODUCT; THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED
WARRANTIES AND LIMITS THE DURATION OF ANY AND ALL IMPLIED WARRANTIES, INCLUD-
ING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TO TWO
(2) YEARS FROM THE DATE OF FIRST PURCHASE; AND DESA HEATING PRODUCTSʼ LIABILITY IS
HEREBY LIMITED TO THE PURCHASE PRICE OF THE PRODUCT AND DESA HEATING PRODUCTS
SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCI-
DENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of
incidental or consequential damages, so the above limitation on implied warranties or exclusion or limitation on
damages may not apply to you.
This warranty gives you specific legal rights and you may also have other rights that vary from state to state.
For information about this warranty write:
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
Patent Pending
117001-01
Rev. A
117001 01
05/05
NOT A UPC
Download from Www.Somanuals.com. All Manuals Search And Download.
|