Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY:
We at DigiTech are proud of our products and back-up each one with the following warranty:
The warranty registration card must be mailed within ten days after purchase date to validate this warranty.
DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship
under normal use and service.
DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect,
provided the product is returned to DigiTechWITH RETURN AUTHORIZATION, where all parts and labor will be
covered up to a period of one year (this warranty is extended to a period of six years when the product has been properly
registered by mail or through our website). A Return Authorization number may be obtained from DigiTech by telephone.
The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly.
Proof-of-purchase is considered to be the burden of the consumer.
DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without
incurring any obligation to install the same on products previously manufactured.
The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone
other than a certified DigiTech technician or, if the product is used with voltages outside of the range suggested by the
manufacturer.
The foregoing is in lieu of all other warranties, expressed or implied, and DigiTech neither assumes nor authorizes any
person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its
dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes
beyond their control.
NOTE:The information contained in this manual is subject to change at any time without notification. Some information
contained in this manual may also be inaccurate due to undocumented changes in the product or operating system since
this version of the manual was completed.The information contained in this version of the owner's manual supersedes all
previous versions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
More than a remarkable achievement, HardWire™ represents a collection of
significant improvements in effects pedals for guitar. HardWire pedals provide
a suite of well-known effects, each with superior tone and control. But these
pedals go above and beyond their peers to provide such distinguishing fea-
tures as true bypass, high voltage operation, and true stereo processing mak-
ing them essential additions to the signal chain of players who know about
sound quality and demand the utmost in performance.
Included Items:
•
•
•
•
•
HardWire CR-7 Stereo Chorus
HardWire StompLock™
Foot Switch Glow Sticker
Hook-and-loop Pedalboard Pad
Warranty card
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
1 2 3
4
5
11
6
12
8
7
8
9
10
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
What Does This Do?
1. Level Knob - Controls the chorus level.Turn this knob clockwise
to increase and counter-clockwise to decrease the chorus level.
2. DC Adapter Jack - Connect (an optional) Harman PSꢁ00R
power supply to this jack. Use the proper supply for your area’s
mains line voltage.
3. Speed Knob - Controls the modulation speed of the chorus
effect. Turn the knob clockwise to increase and counter-clockwise
to decrease the speed.
4. Depth Knob - Controls the intensity of the chorus effect. Turn
the knob clockwise for a deep, rich chorus sound and counter-
clockwise for a subtle chorusing of the signal.
5. Type Knob -TheType knob selects one of the seven chorus types:
STUDIO – Studio quality chorus with a wide stereo image.
MULTI –True 8-voice chorus; the lushest chorusing you can
get in a pedal.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
MODERN – dual voice chorusing that’s both very rich and
smooth.
BOUTIQUE – a rich chorus with the quirkiness of analog
circuits.
ANALOG – distinctively organic bucket-brigade chorus.
JAZZ – single voice chorusing with a dry output – jazzers rejoice!
VINTAGE – warm and versatile from subtle to euphoric.
6. Input 1 (Mono) - Connect your instrument, additional pedal, or
an amp effects send to this jack. Signals are heard at both outputs
when only the Input ꢀ (Mono) jack is used.This jack enables battery
power to the pedal when connected.To prolong battery life, discon-
nect the cable from the Input ꢀ (Mono) jack when not in use. If the
optional Harman PSꢁ00R power supply is used, cables can remain
connected.
ꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Input 2 - Connect a second input to this jack for stereo operation.
Inputs ꢀ and ꢁ are processed separately through the stereo chorus
effect and then fed to Outputs ꢀ and ꢁ keeping true stereo separa-
tion between channels.
8. Foot Switch Release Pins -These two pins are spring loaded
hinges that hold the Foot Switch in place. See page 9 for informa-
tion on accessing and changing the battery.
9. Indicator LED - Lights when the effect is turned on.When bat-
tery power is low (approximately ꢀꢄ minutes before it dies), the
Indicator LED begins to dim giving you advanced warning that very
shortly you will need to replace the battery.
10. Foot Switch -Turns the effect on and off.
11. Output 1 (Mono) - Connect this output to the input of a single
guitar amplifier, another pedal input, or an amp effects return.
ꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Output 2 - Connect this output to a second guitar amplifier when
two amplifiers are being used.
Note: Use unbalanced mono instrument cables only.
ꢅ
Download from Www.Somanuals.com. All Manuals Search And Download.
Amp Setup
PS200R (optional)
or
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Effects Loop Setup
AMP RETURN
AMP SEND
PS200R
(optional)
Note: If the amp effects loop has a mix control, set the mix to
8
100% full wet.
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Operation
In the event that battery power is completely depleted, HardWire pedals
automatically switch into bypass.This eliminates the need to remove the
pedal from your pedal chain if the battery is dead. To replace the battery, do
the following:
ꢀ. Using the tip of a ꢀ/ꢃ” guitar cable, push in one of the Release Pins in on
either side of the Foot Switch, and remove it from the pedal chassis.
ꢁ. Remove the battery from the battery compartment and disconnect the
battery cable.
ꢂ. Connect a new battery to the battery cable and put it back in the bat-
tery compartment. Make sure the battery cable does not interfere with
the spring or pedal switch arm.
ꢃ. Place one hole of the Foot Switch over its corresponding pin.
ꢄ. Push the opposite pin in and lower the other side of the Foot Switch
into place over the depressed pin. Release the pin.When the Foot
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch is properly fastened, both Release Pins are flush with the outer
side of the pedal.
Foot Switch
Pedal Switch
Arm
9VDC Battery
Foot Switch
Release Pin
Battery
Compartment
Foot Switch
Release Pin
Spring
Pedal Chassis
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
HardWire Performance Accessories
The performance accessories make integrating a HardWire pedal into any
pedal board a snap.The following accessories are included:
•
Hook-and-loop Pedalboard Pad (designed to attach to the surfaces
found on most commercial pedal boards)
•
•
Foot Switch Glow Sticker (easily visible on dark stages)
StompLock™ (keeps your settings where you want them)
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Hook-and-loop Pedalboard Pad
To attach the Pedalboard Pad, do the following:
ꢀ. Peel off the existing rubber skid pad from the bottom of the pedal.
ꢁ. Peel the adhesive protector from the back of the Pedalboard Pad.
ꢂ. Apply the Pedalboard Pad to the bottom of the pedal.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Foot Switch Glow Sticker
To attach the Foot Switch Glow Sticker, do the following:
ꢀ. Peel the adhesive backing from the Foot Switch Glow Sticker.
ꢁ. Apply the Glow Sticker to the top of the Foot Switch.
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
StompLock
To place the StompLock over the pedal knobs, do the following:
ꢀ. Set the knobs to your preferred setting.
ꢁ. Gently push the StompLock over the top of the knobs.
ꢂ. To remove the StompLock, gently lift one side and then the other.
ꢀꢃ
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Controls - Level, Speed, Depth,Type, On/Off Pedal
Jacks - Input ꢀ (Mono), Input ꢁ, Output ꢀ (Mono), Output ꢁ
Input Impedance - >ꢀ MΩ (stereo), >ꢄ00 kΩ (mono) - effect on
Output Impedance - ꢀ kΩ - effect on
Input Impedance - true hardwire bypass - effect off
Output Impedance - true hardwire bypass - effect off
Power Supply - 9V Alkaline Dry Battery or
Harman PSꢁ00R 9V DC power supply
Current Draw - 70 mA (typical at 9V DC)
Power Consumption - ꢅꢁꢄ mW (typical w/optional PSꢁ00R power supply)
Dimensions - ꢄ.ꢁꢄ”(L) x ꢂ.ꢄ”(W) x ꢁ.ꢀꢄ”(H)
Weight - ꢀ.ꢂ lbs.
Optional Power Supply:
PSꢁ00R-ꢀ00 (ꢀ00V~ ꢄ0/ꢅ0Hz)
PSꢁ00R-ꢀꢁ0 (ꢀꢁ0V~ ꢅ0Hz)
PSꢁ00R-ꢁꢂ0 (ꢁꢂ0V~ ꢄ0Hz)
PSꢁ00R-ꢁꢃ0 (ꢁꢃ0V~ ꢄ0Hz)
ꢀꢄ
Download from Www.Somanuals.com. All Manuals Search And Download.
8760 South Sandy Parkway
Sandy, Utah 84070
PH (801) 566-8800
FAX (801) 566-7005
HardWire and DigiTech are trademarks
of the Harman Music Group Inc.
Copyright - Harman Music Group
Manufactured in the USA
HardWire CR-7
Owners Manual 18-0618-A
Please visit us
on the World Wide Web at:
Download from Www.Somanuals.com. All Manuals Search And Download.
|