STK17TA8
128k X 8 AutoStore™ nvSRAM
with Real Time Clock
Features
Description
■ nvSRAMCombinedwithIntegratedRealTimeClockFunctions
(RTC, Watchdog Timer, Clock Alarm, Power Monitor)
The Cypress STK17TA8 combines a 1 Mb nonvolatile static RAM
(nvSRAM) with a full featured real time clock in a reliable,
monolithic integrated circuit.
■ Capacitor or Battery Backup for RTC
■ 25, 45 ns Read Access and Read/Write Cycle Time
■ Unlimited Read/Write Endurance
The 1 Mb nvSRAM is a fast static RAM with a nonvolatile
Quantum Trap storage element included with each memory cell.
The SRAM provides the fast access and cycle times, ease of use
and unlimited read and write endurance of a normal SRAM. Data
transfers automatically to the nonvolatile storage cells when
power loss is detected (the STORE operation). On power up,
data is automatically restored to the SRAM (the RECALL
operation). Both STORE and RECALL operations are also
available under software control.
■ Automatic nonvolatile STORE on Power Loss
■ Nonvolatile STORE Under Hardware or Software Control
■ Automatic RECALL to SRAM on Power Up
■ Unlimited RECALL Cycles
The real time clock function provides an accurate clock with leap
year tracking and a programmable, high accuracy oscillator. The
Alarm function is programmable for one-time alarms or periodic
minutes, hours, or days alarms. There is also a programmable
watchdog timer for processor control.
■ 200K STORE Cycles
■ 20-Year nonvolatile Data Retention
■ Single 3 V +20%, -10% Power Supply
■ Commercial and Industrial Temperatures
■ 48-pin 300-mil SSOP Package (RoHS-Compliant)
Logic Block Diagram
VCC
VCAP
Quantum Trap
1024 X 1024
A5
A6
A7
A8
VRTCbat
VRTCcap
POWER
CONTROL
STORE
STORE/
RECALL
CONTROL
STATIC RAM
ARRAY
1024 X 1024
A9
RECALL
A12
A13
A14
A15
A16
HSB
SOFTWARE
DETECT
A15 – A0
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
COLUMN I/O
X1
COLUMN DEC
RTC
X2
INT
A0 A1 A2 A3 A4 A10 A11
A16 – A0
MUX
G
E
W
Cypress Semiconductor Corporation
Document #: 001-52039 Rev. **
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised March 02, 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
RF (SSOP-48) Package Thermal Characteristics
θ 6.2 C/W; θ 51.1 [0fpm], 44.7 [200fpm], 41.8 C/W [500fpm]
Absolute Maximum Ratings
jc
ja
Voltage on Input Relative to Ground ................–0.1V to 4.1V
Voltage on Input Relative to V .........–0.5V to (V + 0.5V)
SS
CC
Note: Stresses greater than those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device.
This is a stress rating only, and functional operation of the device
at conditions above those indicated in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
reliablity.
Voltage on DQ or HSB.....................–0.5V to (V + 0.5V)
0-7
CC
Temperature under Bias ............................... –55°C to 125°C
Junction Temperature................................... –55°C to 140°C
Storage Temperature.................................... –65°C to 150°C
Power Dissipation............................................................. 1W
DC Output Current (1 output at a time, 1s duration)..... 15mA
DC Electrical Characteristics
(V = 2.7V-3.6V)
CC
Commercial
Industrial
Units
Notes
Symbol
Parameter
Average V Current
Min
Max
Min
Max
I
65
50
70
55
mA
mA
t
t
= 25 ns
= 45 ns
CC
CC
AVAV
1
AVAV
Dependent on output loading and
cycle rate. Values obtained
without output loads.
I
I
Average V Current during
STORE
3
3
mA All Inputs Don’t Care, V = max
CC
CC
CC
2
3
Average current for duration of
STORE
cycle (t
)
STORE
Average V Current at t
=
10
10
mA W ≥ (V – 0.2V)
CC
CC
CC
AVAV
200ns
3V, 25°C, Typical
All Other Inputs Cycling at CMOS
Levels
Dependent on output loading and
cycle rate. Values obtained
without output loads.
I
I
Average V
<Emphasis>AutoStore™ Cycle
Current during
3
3
3
3
mA All Inputs Don’t Care
CC
CAP
4
Average current for duration of
STORE cycle (t
)
STORE
V
Standby Current
mA E ≥ (V -0.2V)
SB
CC
CC
(Standby, Stable CMOS Levels)
All Others V ≤ 0.2V or ≥
IN
(V -0.2V)
CC
Standby current level after
nonvolatile cycle complete
I
I
Input Leakage Current
±1
±1
±1
±1
mA
mA
V
V
= max
CC
ILK
= V to V
IN
SS
CC
Off-State Output Leakage Current
V
V
= max
CC
OLK
= V to V , E or G ≥ V
IN
SS
CC
IH
V
V
V
V
Input Logic “1” Voltage
Input Logic “0” Voltage
Output Logic “1” Voltage
Output Logic “0” Voltage
2.0
–0.5
V
+ 0.5
2.0
V + 0.5
CC
V
V
V
V
All Inputs
All Inputs
IH
CC
V
0.8
V –0.5
SS
0.8
IL
SS
2.4
2.4
I
I
=–2 mA (except HSB)
= 4 mA
OH
OL
OUT
OUT
0.4
0.4
Note: The HSB pin has I
=-10uA for V of 2.4V, this parameter is characterized but not tested.
OH
OUT
Note: The INT is open-drain and does not source or sink high current when interrupt Register bit D3 is below.
Document #: 001-52039 Rev. **
Page 3 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
DC Electrical Characteristics (continued)
(V = 2.7V-3.6V)
CC
Commercial
Industrial
Units
Notes
Symbol
Parameter
Min
Max
70
Min
Max
85
T
Operating Temperature
Operating Voltage
0
–40
2.7
17
°C
A
V
2.7
17
3.6
57
3.6
57
V
3.0V +20%, -10%
pin and V , 5V
CC
V
Storage Capacitance
μF Between V
CAP
CAP
SS
rated.
NV
Nonvolatile STORE operations
Data Retention
200
20
200
20
K
C
DATA
Years At 55 °C
R
AC Test Conditions
Input Pulse Levels ....................................................0V to 3V
Input Rise and Fall Times ............................................ <5 ns
Input and Output Timing Reference Levels .................... 1.5V
Capacitance
(T = 25°C, f = 1.0MHz)
A
Parameter
Input Capacitance
Output Capacitance
Max
7
Units
Conditions
ΔV = 0 to 3V
ΔV = 0 to 3V
Symbol
C
C
pF
pF
IN
7
OUT
Figure 2. AC Output Loading
3.0V
577 Ohms
OUTPUT
30 pF
789 Ohms
INCLUDING
SCOPE AND
FIXTURE
Figure 3. AC Output Loading for Tristate Specs (tHZ, tLZ, tWLQZ, tWHQZ, tGLQX, tGHQZ
3.0V
577 Ohms
OUTPUT
5 pF
789 Ohms
INCLUDING
SCOPE AND
FIXTURE
Notes
2. These parameters are guaranteed but not tested.
Document #: 001-52039 Rev. **
Page 4 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
RTC DC Characteristics
Commercial
Industrial
Symbol
Parameter
Units
Notes
Min
—
Max
300
3.3
Min
Max
350
3.3
IBAK
VRTCbat
RTC Backup Current
—
nA
V
From either V
or V
RTCcap RTCbat
RTC Battery Pin Voltage
1.8
1.8
Typical = 3.0 Volts during normal
operation
VRTCcap
tOSCS
RTC Capacitor Pin Voltage
RTC Oscillator time to start
1.2
—
2.7
10
5
1.2
—
2.7
10
5
V
Typical = 2.4 Volts during normal
operation
sec
sec
AtMINTemperature from Power up
or Enable
—
—
At 25°C from Power up or Enable
Figure 4. RTC Recommended Component Configuration
X1
X2
Recommended Values
Y1
= 32.768 KHz
= 10M Ohm
RF
C1
= 0 (install cap footprint,
but leave unloaded)
C2 = 56 pF ± 10% (do not vary from this value)
Document #: 001-52039 Rev. **
Page 5 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
SRAM READ Cycles #1 and #2
Symbols
NO.
STK17TA8-25 STK17TA8-45
Parameter
Chip Enable Access Time
Units
#1
#2
Alt.
Min
Max
Min
Max
1
2
3
4
5
6
7
t
t
t
t
t
t
t
t
t
t
t
t
t
t
25
45
ns
ns
ns
ns
ns
ns
ns
ELQV
ACS
RC
AA
[3]
[3]
t
t
Read Cycle Time
25
45
AVAV
ELEH
[4]
Address Access Time
25
12
45
20
AVQV
AVQV
GLQV
AXQX
ELQX
EHQZ
Output Enable to Data Valid
Output Hold after Address Change
Address Change or Chip Enable to Output Active
OE
OH
LZ
[4]
[4]
[5]
t
3
3
3
3
AXQX
Address Change or Chip Disable to Output
Inactive
10
15
HZ
8
9
t
t
t
t
t
t
t
t
Output Enable to Output Active
Output Disable to Output Inactive
Chip Enable to Power Active
Chip Disable to Power Standby
0
0
0
0
ns
ns
ns
ns
GLQX
OLZ
OHZ
PA
10
25
15
45
GHQZ
10
11
ELICCL
EHICCH
PS
Figure 5. SRAM READ Cycle #1: Address Controlled
tAVAV
ADDRESS
tAVQV
tAXQX
DQ (DATA OUT)
DATA VALID
Figure 6. SRAM READ Cycle #2: E and G Controlled
Notes
3. W must be high during SRAM READ cycles.
4. Device is continuously selected with E and G both low
5. Measured ± 200mV from steady state output voltage.
6. HSB must remain high during READ and WRITE cycles.
Document #: 001-52039 Rev. **
Page 6 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
SRAM WRITE Cycles #1 and #2
Symbols
NO.
STK17TA8-25 STK17TA8-45
Parameter
Write Cycle Time
Units
#1
#2
Alt.
Min
25
20
20
10
0
Max
Min
45
30
30
15
0
Max
11
13
14
15
16
17
18
19
20
21
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
AVAV
AVAV
WC
Write Pulse Width
WLWH
ELWH
DVWH
WHDX
AVWH
AVWL
WHAX
WLEH
ELEH
DVEH
EHDX
AVEH
AVEL
EHAX
WP
CW
DW
DH
AW
AS
Chip Enable to End of Write
Data Set-up to End of Write
Data Hold after End of Write
Address Set-up to End of Write
Address Set-up to Start of Write
Address Hold after End of Write
Write Enable to Output Disable
Output Active after End of Write
20
0
30
0
0
0
WR
WZ
OW
10
15
WLQZ
WHQX
3
3
Figure 7. SRAM WRITE Cycle #1: W Controlled
tAVAV
ADDRESS
tWHAX
tELWH
E
tAVWH
tAVWL
tWLWH
W
tDVWH
tWHDX
DATA IN
DATA IN
DATA VALID
tWLQZ
tWHQX
HIGH IMPEDANCE
DATA OUT
PREVIOUS DATA
Figure 8. SRAM WRITE Cycle #2: E Controlled
tAVAV
ADDRESS
E
tAVEL
tELEH
tEHAX
tAVEH
tWLEH
W
tDVEH
tEHDX
DATA IN
DATA VALID
HIGH IMPEDANCE
DATA OUT
Notes
7. If W is low when E goes low, the outputs remain in the high-impedance state.
8. E or W must be ≥ VIH during address transitions.
Document #: 001-52039 Rev. **
Page 7 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
AutoStore/Power Up Recall
Symbols
NO.
STK17TA8
Parameter
Power-up RECALL Duration
Units
Notes
Standard
Alternate
Min
Max
40
22
23
24
25
t
t
ms
ms
V
HRECALL
STORE
t
STORE Cycle Duration
12.5
2.65
HLHZ
V
V
Low Voltage Trigger Level
SWITCH
CCRISE
V
Rise Time
150
μS
CC
Figure 9. AutoStore/Power Up RECALL
NOTE: Read and Write cycles will be ignored during STORE, RECALL and while V is below V
CC
SWITCH
Notes
9.
t
starts from the time V rises above V
CC SWITCH
HRECALL
10. If an SRAM WRITE has not taken place since the last nonvolatile cycle, no STORE will take place
11. Industrial Grade Devices require 15 ms MAX.
Document #: 001-52039 Rev. **
Page 8 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Software-Controlled STORE/RECALL Cycle
In the following table, the software controlled STORE and RECALL cycle parameters are listed.
Symbols
G Cont Alternate
STK17TA8-35 STK17TA8-45
NO.
Parameter
Units Notes
E Cont
Min
Max
Min
Max
26
t
t
t
RC
STORE / RECALL Initiation Cycle
Time
25
45
ns
AVAV
AVAV
27
28
29
30
t
t
t
t
t
t
t
t
tAS
Address Set-up Time
Clock Pulse Width
Address Hold Time
RECALL Duration
0
20
1
0
30
1
ns
ns
ns
μs
AVEL
AVGL
tCW
ELEH
GLGH
GHAX
RECALL
EHAX
RECALL
100
100
Figure 10. Software STORE/RECALL Cycle: E CONTROLLED
Figure 11. Software STORE/RECALL Cycle: G Controlled
Notes
12. The software sequence is clocked on the falling edge of E controlled READs or G controlled READs
13. The six consecutive addresses must be read in the order listed in the Software STORE/RECALL Mode Selection Table W must be high during all six consecutive cycles.
Document #: 001-52039 Rev. **
Page 9 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Hardware STORE Cycle
Symbols
NO.
STK17TA8
Min Max
70
Parameter
Units
Notes
Standard Alternate
31
32
t
t
t
Hardware STORE to SRAM Disabled
Hardware STORE Pulse Width
1
μs
14
DELAY
HLHX
HLQZ
15
ns
Figure 12. Hardware STORE Cycle
Soft Sequence Commands
NO.
Symbols
Standard
Parameter
STK17TA8
Min Max
70
Units
Notes
33
t
Soft Sequence Processing Time
μs
SS
Figure 13. Soft Sequence Commands
Notes
14. On a hardware STORE initiation, SRAM operation continues to be enabled for time tDELAY to allow READ/WRITE cycles to compete.
15. This is the amount of time that it takes to take action on a soft sequence command. Vcc power must remain high to effectively register command.
16. Commands like Store and Recall lock out I/O until operation is complete which further increases this time. See specific command.
Document #: 001-52039 Rev. **
Page 10 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
MODE Selection
E
W
G
A
-A
Mode
I/O
Power
Notes
16
0
H
L
L
L
X
H
L
X
L
X
L
X
Not Selected
Read SRAM
Write SRAM
Output High Z
Output Data
Input Data
Standby
Active
X
X
Active
H
0x04E38
0x0B1C7
0x083E0
0x07C1F
0x0703F
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Active
0x08FC0
Nonvolatile Store
Output High Z
I
CC2
L
H
L
0x04E38
0x0B1C7
0x083E0
0x07C1F
0x0703F
0x04C63
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Read SRAM
Output Data
Output Data
Output Data
Output Data
Output Data
Output High Z
Active
Nonvolatile Recall
Notes
17. The six consecutive addresses must be in the order listed. W must be high during all six consecutive cycles to enable a nonvolatile cycle.
18. While there are 17 addresses on the STK17TA8, only the lower 16 are used to control software modes
19. I/O state depends on the state of G. The I/O table shown assumes G low
Document #: 001-52039 Rev. **
Page 11 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
(activated by HSB), Software Store (activated by an address
sequence), and AutoStore (on power down).
nvSRAM Operation
The STK17TA8 nvSRAM is made up of two functional compo-
nents paired in the same physical cell. These are the SRAM
memory cell and a nonvolatile QuantumTrap cell. The SRAM
memory cell operates like a standard fast static RAM. Data in the
SRAM can be transferred to the nonvolatile cell (the STORE
operation), or from the nonvolatile cell to SRAM (the RECALL
operation). This unique architecture enables all cells to be stored
and recalled in parallel. During the STORE and RECALL opera-
tions SRAM READ and WRITE operations are inhibited. The
STK17TA8 supports unlimited read and writes like a typical
SRAM. In addition, it provides unlimited RECALL operations
from the nonvolatile cells and up to 200K STORE operations.
AutoStore operation, a unique feature of Cypress QuanumTrap
technology is a standard feature on the STK17TA8.
During normal operation, the device draws current from V to
CC
charge a capacitor connected to the V
pin. This stored
CAP
charge is used by the chip to perform a single STORE operation.
If the voltage on the V pin drops below V , the part
CC
SWITCH
automatically disconnects the V
pin from V . A STORE
CAP
CC
operation is initiated with power provided by the V
capacitor.
CAP
Figure 14 shows the proper connection of the storage capacitor
CAP
voltage on the V pin is driven to 5V by a charge pump internal
CAP
SRAM READ
to the chip. A pull up should be placed on W to hold it inactive
during power up.
The STK17TA8 performs a READ cycle whenever E and G are
low while W and HSB are high. The address specified on pins
To reduce unneeded nonvolatile stores, AutoStore and
Hardware Store operations are ignored unless at least one
WRITE operation has taken place since the most recent STORE
or RECALL cycle. Software initiated STORE cycles are
performed regardless of whether a WRITE operation has taken
place. The HSB signal can be monitored by the system to detect
an AutoStore cycle is in progress.
A
determine which of the 131,072 data bytes are accessed.
0-16
When the READ is initiated by an address transition, the outputs
are valid after a delay of t (READ cycle #1). If the READ is
AVQV
initiated by E and G, the outputs are valid at t
whichever is later (READ cycle #2). The data outputs repeatedly
respond to address changes within the t access time
without the need for transitions on any control input pins, and
remain valid until another address change or until E or G is
brought high, or W and HSB is brought low.
or at t
,
ELQV
GLQV
AVQV
Hardware STORE (HSB) Operation
The STK17TA8 provides the HSB pin for controlling and
acknowledging the STORE operations. The HSB pin can be
used to request a hardware STORE cycle. When the HSB pin is
driven low, the STK17TA8 conditionally initiates a STORE
Figure 14. AutoStore Mode
VCC
VCAP
VCC
operation after t
. An actual STORE cycle only begins if a
DELAY
WRITE to the SRAM took place since the last STORE or
RECALL cycle. The HSB pin has a very resistive pullup and is
internally driven low to indicate a busy condition while the
STORE (initiated by any means) is in progress. This pin should
be externally pulled up if it is used to drive other inputs.
W
SRAM READ and WRITE operations that are in progress when
HSB is driven low by any means are given time to complete
before the STORE operation is initiated. After HSB goes low, the
STK17TA8 continues to allow SRAM operations for t
.
DELAY
During t
, multiple SRAM READ operations may take place.
DELAY
If a WRITE is in progress when HSB is pulled low, it is allowed a
time, t , to complete. However, any SRAM WRITE cycles
DELAY
requested after HSB goes low is inhibited until HSB returns high.
SRAM WRITE
If HSB is not used, it should be left unconnected.
A WRITE cycle is performed whenever E and W are low and HSB
is high. The address inputs must be stable prior to entering the
WRITE cycle and must remain stable until either E or W goes
high at the end of the cycle. The data on the common I/O pins
Hardware RECALL (POWER-UP)
During power up or after any low power condition
(V <V
), an internal RECALL request is latched. When
CC
SWITCH
DQ0-7 is written into memory if it is valid t
before the end
DVWH
V
once again exceeds the sense voltage of V
, a
SWITCH
CC
of a W controlled WRITE or t
controlled WRITE.
before the end of an E
DVEH
RECALL cycle is automatically initiated and takes t
complete.
to
HRECALL
It is recommended that G be kept high during the entire WRITE
cycle to avoid data bus contention on common I/O lines. If G is
Software STORE
left low, internal circuitry turns off the output buffers t
W goes low.
after
WLQZ
Data can be transferred from the SRAM to the nonvolatile
memory by a software address sequence. The STK17TA8
software STORE cycle is initiated by executing sequential E
controlled or G controlled READ cycles from six specific address
locations in exact order. During the STORE cycle, previous data
is erased and then the new data is programmed into the nonvol-
AutoStore Operation
The STK17TA8 stores data to nvSRAM using one of three
storage operations. These three operations are Hardware Store
Document #: 001-52039 Rev. **
Page 12 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
atile elements. Once a STORE cycle is initiated, further memory
inputs and outputs are disabled until the cycle is completed.
Preventing AutoStore
Because of the use of nvSRAM to store critical RTC data, the
AutoStore function cannot be disabled on the STK17TA8.
To initiate the Software STORE cycle, the following read
sequence must be performed:
Best Practices
1. Read Address 0x4E38 Valid READ
2. Read Address 0xB1C7 Valid READ
3. Read Address 0x83E0 Valid READ
4. Read Address 0x7C1F Valid READ
5. Read Address 0x703F Valid READ
6. Read Address 0x8FC0 Initiate STORE Cycle
nvSRAM products have been used effectively for over 15 years.
While ease-of-use is one of the product’s main system values,
experience gained working with hundreds of applications has
resulted in the following suggestions as best practices:
■ The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer’s
sitessometimesreprogramthesevalues. FinalNVpatternsare
typically repeating patterns of AA, 55, 00, FF, A5, or 5A. End
product’s firmware should not assume an NV array is in a set
programmed state. Routines that check memory content
values to determine first time system configuration, cold or
warm boot status, should always program a unique NV pattern
(for example, complex 4-byte pattern of 46 E6 49 53 hex or
more random bytes) as part of the final system manufacturing
test to ensure these system routines work consistently.
Once the sixth address in the sequence has been entered, the
STORE cycle starts and the chip is disabled. It is important that
READ cycles and not WRITE cycles be used in the sequence
and that G is active. After the t
cycle time has been fulfilled,
STORE
the SRAM is again activated for READ and WRITE operation.
Software RECALL
Data is transferred from nonvolatile memory to the SRAM by a
software address sequence. A Software RECALL cycle is
initiated with a sequence of READ operations in a manner similar
to the Software STORE initiation. To initiate the RECALL cycle,
the following sequence of E or G controlled or READ operations
must be performed:
■ Power up boot firmware routines should rewrite the nvSRAM
into the desired state (autostore enabled and so on). While the
nvSRAM is shipped in a preset state, best practice is to again
rewrite the nvSRAM into the desired state as a safeguard
against events that might flip the bit inadvertently (program
bugs, incoming inspection routines, and so on.
1. Read Address 0x4E38 Valid READ
2. Read Address 0xB1C7 Valid READ
3. Read Address 0x83E0 Valid READ
4. Read Address 0x7C1F Valid READ
5. Read Address 0x703F Valid READ
6. Read Address 0x4C63 Initiate RECALL Cycle
■ The OSCEN bit in the Calibration register at 0x1FFF8 should
be set to 1 to preserve battery life when the system is in storage
■ The V
value specified in this data sheet includes a minimum
cap
Internally, RECALL is a two-step procedure. First, the SRAM
data is cleared, and second, the nonvolatile information is trans-
and a maximum value size. Best practice is to meet this
requirement and not exceed the max V
nvSRAM internal algorithm calculates V
on this max Vcap value. Customers that want to use a larger
value because the
charge time based
cap
ferred into the SRAM cells. After the t
cycle time, the
RECALL
cap
SRAM is once again be ready for READ or WRITE operations.
The RECALL operation in no way alters the data in the nonvol-
atile storage elements.
V
value to make sure there is extra store charge and store
cap
time should discuss their V
understand any impact on the V
size selection with Cypress to
cap
Data Protection
voltage level at the end of
cap
a t
period.
RECALL
The STK17TA8 protects data from corruption during low-voltage
conditions by inhibiting all externally initiated STORE and
WRITE operations. The low voltage condition is detected when
Low Average Active Power
CMOS technology provides the STK17TA8 with the benefit of
power supply current that scales with cycle time. Less current is
drawn as the memory cycle time becomes longer than 50 ns.
V
<V
.
CC
SWITCH
If the STK17TA8 is in a WRITE mode (both E and W low) at
power-up, after a RECALL, or after a STORE, the WRITE will be
inhibited until a negative transition on E or W is detected. This
protects against inadvertent writes during power up or brown out
conditions.
Figure 15 shows the relationship between
READ/WRITE cycle time. Worst-case current consumption is
shown for commercial temperature range, V =3.6V, and chip
enable at maximum frequency. Only standby current is drawn
when the chip is disabled. The overall average current drawn by
the STK17TA8 depends on the following items:
I
and
CC
CC
Noise Considerations
The STK17TA8 is a high speed memory and so must have a high
frequency bypass capacitor of 0.1 µF connected between both
1. The duty cycle of chip enable.
2. The overall cycle rate for accesses.
3. The ration of READs to WRITEs.
4. The operating temperature.
5. The VCC level.
V
pins and V ground plane with no plane break to chip V
.
CC
SS
SS
Use leads and traces that are as short as possible. As with all
high speed CMOS ICs, careful routing of power, ground, and
signals reduces circuit noise.
6. I/O loading.
Document #: 001-52039 Rev. **
Page 13 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Figure 15. Current versus Cycle Time
You can power the real time clock with either a capacitor or a
battery. Factors to be considered when choosing a backup
power source include the expected duration of power outages
and the cost and reliability trade-off of using a battery versus a
capacitor.
If you select a capacitor power source, connect the capacitor to
the V
pin and leave the V
pin unconnected.
RTCcap
RTCbat
Capacitor backup time values based on maximum current specs
are shown below. Nominal times are approximately three times
longer.
Capacitor Value
0.1 F
Backup Time
72 hours
14 days
0.47 F
1.0 F
30 days
A capacitor has the obvious advantage of being more reliable
and not containing hazardous materials. The capacitor is
recharged every time the power is turned on so that real time
clock continues to have the same backup time over years of
operation.
RTC Operations
Real Time Clock
The clock registers maintain time up to 9,999 years in one
second increments. The user can set the time to any calendar
time and the clock automatically keeps track of days of the week
and month, leap years, and century transitions. There are eight
registers dedicated to the clock functions which are used to set
time with a write cycle and to read time during a read cycle.
These registers contain the Time of Day in BCD format. Bits
defined as "0" are currently not used and are reserved for future
use by Cypress.
If you select a battery power source, connect the battery to the
V
pin and leave the V
pin unconnected. A 3V lithium
RTCbat
RTCcap
battery is recommended for this application. The battery capacity
should be chosen for the total anticipated cumulative down-time
required over the life of the system.
The real time clock is designed with a diode internally connected
to the V
pin. This prevents the battery from ever being
RTCbat
charged by the circuit.
Reading The Clock
Stopping And Starting The RTC Oscillator
The user should halt internal updates to the real time clock
registers before reading clock data to prevent the reading of data
in transition. Stopping the internal register updates does not
affect clock accuracy.
The OSCEN bit in Calibration register at 0x1FFF8 enables RTC
oscillator operation. This bit is nonvolatile and shipped to
customers in the “enabled” state (set to 0). OSCEN should be set
to a 1 to preserve battery life while the system is in storage. This
turns off the oscillator circuit extending the battery life. If the
OSCEN bit goes from disabled to enabled, it typically takes 5
seconds (10 seconds max) for the oscillator to start.
Write a “1” to the read bit "R" (in the Flags register at 0x1FFF0)
captures the current time in holding registers. Clock updates will
not restart until a “0” is written to the read bit. The RTC registers
can then be read while the internal clock continues to run.
The STK17TA8 has the ability to detect oscillator failure due to
loss of backup power. The failure is recorded by the OSCF
(Oscillator Failed) bit of the Flags register (at address 0x1FFF0).
Within 20ms after a “0” is written to the read bit, all real time clock
registers are simultaneously updated.
When the device is powered on (V goes above V
), the
Setting The Clock
CC
SWITCH
OSCEN bit is checked for "enabled" status. If the OSCEN bit is
enabled and the oscillator is not active within the first 5 ms, the
OSCF bit is set. The user should check for this condition and then
write a 0 to clear the flag. When the OSCF flag bit is set, the real
time clock registers are reset to the “Base Time” (see the section
"Setting the Clock"), the value last written to the real time clock
registers.
Set the write bit “W” (in the Flags register at 0x1FFF0) to a "1" to
enable the time to be set. The correct day, date and time can then
be written into the real time clock registers in 24-hour BCD
format. The time written is referred to as the "Base Time." This
value is stored in nonvolatile registers and used in calculation of
the current time. Reset the write bit to "0" to transfer the time to
the actual clock counters. The clock starts counting at the new
base time.
The value of OSCF should be reset to 0 when the real time clock
registers are written for the first time. This initializes the state of
this bit which may have become set when the system was first
powered on.
Backup Power
The RTC in intended to keep time even when system power is
To reset OSCF, set the write bit “W” (in the Flags register at
0x1FFF0) to a "1" to enable writes to the Flag register. Write a
“0” to the OSCF bit. and thenreset the write bit to "0" to disable
writes.
lost. When primary power, V , drops below V
time clock switches to the backup power supply connected to
, the real
CC
SWITCH
either the V or V pin.
RTCcap
RTCbat
The clock oscillator uses a maximum of 300 nanoamps at 2 volts
to maximize the backup time available from the backup source.
Document #: 001-52039 Rev. **
Page 14 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
The alarm value should be initialized on power-up by software
since the alarm registers are not nonvolatile.
Calibrating The Clock
The RTC is driven by a quartz controlled oscillator with a nominal
frequency of 32.768 KHz. Clock accuracy will depend on the
quality of the crystal, specified (usually 35 ppm at 25 C). This
error could equate to 1.53 minutes gain or loss per month. The
STK17TA8 employs a calibration circuit that can improve the
accuracy to +1/-2 ppm at 25 C. The calibration circuit adds or
subtracts counts from the oscillator divider circuit.
To set or clear Alarm registers, set the write bit “W” (in the Flags
register at 0x1FFF0) to a "1" to enable writes to the Alarm
registers. Write an alarm value to the alarm registers and then
reset the write bit to "0" to disable writes.
Watchdog Timer
The watchdog timer is designed to interrupt or reset the
processor should the program get hung in a loop and not
respond in a timely manner. The software must reload the
watchdog timer before it counts down to zero to prevent this
interrupt or reset.
The number of time pulses are added or substracted depends
upon the value loaded into the five calibration bits found in
Calibration register (at 0x1FFF8). Adding counts speeds the
clock up; subtracting counts slows the clock down. The
Calibration bits occupy the five lower order bits of the register.
These bits can be set to represent any value between 0 and 31
in binary form. Bit D5 is a Sign bit, where a “1” indicates positive
calibration and a “0” indicates negative calibration. Calibration
occurs during a 64 minute period. The first 62 minutes in the
cycle may, once per minute, have one second either shortened
by 128 or lengthened by 256 oscillator cycles.
The watchdog timer is a free running down counter that uses the
32 Hz clock (31.25 ms) derived from the crystal oscillator. The
watchdog timer function does no operate unless the oscillator is
running.
The watchdog counter is loaded with a starting value from the
load register and then counts down to zero setting the watchdog
flag (WDF) and generating an interrupt if the watchdog interrupt
is enabled. The watchdog flag bit is reset when the flag register
is read. The operating software would normally reload the
counter by setting the watchdog strobe bit (WDS) to 1 within the
timing interval programmed into the load register.
If a binary “1” is loaded into the register, only the first 2 minutes
of the 64 minute cycle is modified; if a binary 6 is loaded, the first
12 will be affected, and so on. Therefore each calibration step
has the effect of adding 512 or subtracting 256 oscillator cycles
for every 125,829,120 actual oscillator cycles. That is +4.068 or
-2.034 ppm of adjustment per calibration step in the calibration
register.
To use the watchdog timer to reset the processor on timeout, the
INT is tied to processor master reset and Interrupt register is
programmed to 24h to enable interrupts to pulse the reset pin on
timeout.
The calibration register value is determined during system test
by setting the CAL bit in the Flags register (at 0x1FFF0) to 1. This
causes the INT pin to toggle at a nominal 512 Hz. This frequency
can be measured with a frequency counter. Any deviation
measured from the 512 Hz will indicate the degree and direction
of the required correction. For example, a reading of 512.01024
Hz would indicate a +20 ppm error, requiring a -10 (001010) to
be loaded into the Calibration register. Note that setting or
changing the calibration register does not affect the frequency
test output frequency.
To load the watch dog timer, set a new value into the load register
by writing a “0” to the watchdog write bit (WDW) of the watchdog
register (at 01x1FFF7). Then load a new value into the load
register. Once the new value is loaded, the watchdog write bit is
then set to 1 to disable watchdog writes. The watchdog strobe
bit (WDS) is then set to 1 to load this value into the watchdog
timer.
Note Setting the load register to zero disables the watchdog
timer function.
To set or clear CAL, set the write bit “W” (in the Flags register at
0x1FFF0) to a "1" to enable writes to the Flag register. Write a
value to CAL. and then reset the write bit to "0" to disable writes.
The system software should initialize the watchdog load register
on power-up to the desired value since the register is not nonvol-
atile.
The default Calibration register value from the factory is 00h. The
user calibration value loaded is retained during a power loss.
Power Monitor
Alarm
The STK17TA8 provides a power monitor function. The power
monitor is based on an internal band-gap reference circuit that
The alarm function compares a user-programmable alarm
time/date (stored in registers 0x1FFF1-5) with the real time clock
time-of-day/date values. When a match occurs, the alarm flag
(AF) is set and an interrupt is generated if the alarm interrupt is
enabled. The alarm flag is automatically reset when the Flags
register is read.
compares the V voltage to V
.
CC
SWITCH
When the power supply drops below V
, the real time clock
SWITCH
circuit is switched to the backup supply (battery or capacitor) .
When operating from the backup source, no data may be read
or written to the nvSRAM and the clock functions are not
available to the user. The clock continues to operate in the
Each of the alarm registers has a match bit as its MSB. Setting
the match bit to a 1 disables this alarm register from the alarm
comparison. When the match bit is 0, the alarm register is
compared with the equivalent real time clock register. Using the
match bits, the alarm can occur as specifically as one particular
second on one day of the month or as frequently as once per
minute.
background. Updated clock data is available to the user t
HRECALL
delay after VCC has been restored to the device.
When power is lost, the PF flag in the Flags Register is set to
indicate the power failure and an interrupt is generated if the
power fail interrupt is enabled (interrupt register=20h). This line
would normally be tied to the processor master reset input for
perform power-off reset.
Note The product requires the match bit for seconds(1x1FFF2 -
D7) be set to 0 for proper operation of the Alarm Flag and
Interrupt.
Document #: 001-52039 Rev. **
Page 15 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Power Fail Interrupt Enable (PFE). When set to 1, the INT pin is
driven by a power fail signal from the power monitor circuit. When
set to 0, only the PF flag is set.
Interrupts
The STK17TA8 has a Flags register, Interrupt Register, and
interrupt logic that can interrupt a microcontroller or generate a
power-up master reset signal. There are three potential interrupt
sources: the watchdog timer, the power monitor, and the clock
alarm. Each can be individually enabled to drive the INT pin by
setting the appropriate bit in the Interrupt register. In addition,
each has an associated flag bit in the Flags register that the host
processor can read to determine the interrupt source. Two bits in
the Interrupt register determine the operation of the INT pin
driver.
High/Low (H/L). When set to a 1, the INT pin is active high and
the driver mode is push-pull. The INT pin can drive high only
when V >V
. When set to a 0, the INT pin is active low
CC
SWITCH
and the drive mode is open-drain. The active low (open drain)
output is maintained even when power is lost .
Pulse/Level (P/L). When set to a 1, the INT pin is driven for
approximately 200 ms when an interrupt occurs. The pulse is
reset when the Flags register is read. When P/L is set to a 0, the
INT pin is driven high or low (determined by H/L) until the Flags
register is read.
A functional diagram of the interrupt logic is shown below:
Figure 16. Interrupt Block Diagram
The Interrupt register is loaded with the default value 00h at the
factory. The user should configure the Interrupt register to the
value desired for their desired mode of operation. Once
configured, the value is retained during power failures.
WDF
Watchdog
Timer
WIE
VCC
PF
P/L
Power
Monitor
Pin
Driver
INT
Flags Register
PFE
The Flags register has three flag bits: WDF, AF, and PF. These
flags are set by the watchdog time-out, alarm match, or power
fail monitor respectively. The processor can either poll this
register or enable interrupts to be informed when a flag is set.
The flags are automatically reset once the register is read.
H/L
VINT
VSS
AF
Clock
Alarm
AIE
The Flags register is automatically loaded with the value 00h on
power up (with the exception of the OSCF bit).
Interrupt Register
Watchdog Interrupt Enable (WIE). When set to 1, the watchdog
timer drives the INT pin when a watchdog time-out occurs. When
WIE is set to 0, the watchdog time-out only sets the WDF flag bit.
Alarm Interrupt Enable (AIE). When set to 1, the INT pin is driven
when an alarm match occurs. When set to 0, the alarm match
only sets the AF flag bit.
Document #: 001-52039 Rev. **
Page 16 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
RTC Register
BCD Format Data
Register
Function / Range
D7
0
D6
D5
D4
D3
D2
D1
D0
0x1FFFF
0x1FFFE
10s Years
0
Years
Months
Years: 00-99
0
10s
Months: 01-12
Months
0x1FFFD
0
0
10s Day of
Month
Day of Month
Day of Week
Day of Month: 01-31
0x1FFFC
0x1FFFB
0x1FFFA
0x1FFF9
0x1FFF8
0
0
0
0
0
0
0
0
0
Day of week: 01-07
Hours: 00-23
10s Hours
10s Minutes
Hours
Minutes
Seconds
Minutes: 00-59
Seconds: 00-59
Calibration values*
10s Seconds
OSCEN
[0]
0
Cal
Sign
Calibration[00000]
0x1FFF7
0x1FFF6
WDS
WDW
WDT
Watchdog*
Interrupts*
WIE [0]
AIE [0]
PFE
[0]
0
H/L
[1]
P/L [0]
0
0
0x1FFF5
0x1FFF4
0x1FFF3
0x1FFF2
0x1FFF1
0x1FFF0
M
M
M
M
0
0
10s Alarm Date
10s Alarm Hours
Alarm Day
Alarm, Day of Month: 01-31
Alarm, hours: 00-23
Alarm, minutes: 00-59
Alarm, seconds: 00-59
Centuries: 00-99
Alarm Hours
Alarm Minutes
Alarm Seconds
Centuries
10 Alarm Minutes
10 Alarm Seconds
10s Centuries
AF PF
WDF
OSCF
0
CAL[0]
W[0]
R[0]
Flags*
* A binary value, not a BCD value.
0 - Not implemented, reserved for future use.
Default Settings of nonvolatile Calibration and Interrupt registers from factory
Calibration Register=00h
Interrupt Register=00h
The User should configure to desired value at startup or during operation and the value is then retained during a power failure.
[ ] designates values shipped from the factory. See “Stopping And Starting The RTC Oscillator” on page 14 .
Document #: 001-52039 Rev. **
Page 17 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Register Map Detail
Real Time Clock – Years
D4 D3
0x1FFFF
D7
D6
D5
D2
D1
D0
10s Years
Years
Contains the lower two BCD digits of the year. Lower nibble contains the value for years; upper nibble contains
the value for 10s of years. Each nibble operates from 0 to 9. The range for the register is 0-99.
Real Time Clock – Months
0x1FFFE
0x1FFFD
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
10s Month
Months
Contains the BCD digits of the month. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
(one bit) contains the upper digit and operates from 0 to 1. The range for the register is 1-12.
Real Time Clock – Date
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10s Day of month
Day of month
Contains the BCD digits for the date of the month. Lower nibble contains the lower digit and operates from 0 to 9;
upper nibble contains the upper digit and operates from 0 to 3. The range for the register is 1-31. Leap years are
automatically adjusted for.
Real Time Clock – Day
0x1FFFC
0x1FFFB
0x1FFFA
0x1FFF9
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
Day of week
Lower nibble contains a value that correlates to day of the week. Day of the week is a ring counter that counts from
1 to 7 then returns to 1. The user must assign meaning to the day value, as the day is not integrated with the date.
Real Time Clock – Hours
D7
D6
D5
D4
D3
D2
D1
D0
0
0
10s Hours
Hours
Contains the BCD value of hours in 24 hour format. Lower nibble contains the lower digit and operates from 0 to
9; upper nibble (two bits) contains the upper digit and operates from 0 to 2. The range for the register is 0-23.
Real Time Clock – Minutes
D7
D6
D5
D4
D3
D2
D1
Minutes
D0
0
10s Minutes
Contains the BCD value of minutes. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper minutes digit and operates from 0 to 5. The range for the register is 0-59.
Real Time Clock – Seconds
D7
D6
D5
D4
D3
D2
D1
Seconds
D0
0
10s Seconds
Contains the BCD value of seconds. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper digit and operates from 0 to 5. The range for the register is 0-59.
Calibration
0x1FFF8
D7
D6
D5
D4
D3
D2
D1
D0
OSCEN
0
Calibration
Sign
Calibration
OSCEN
Oscillator Enable. When set to 1, the oscillator is disabled. When set to 0, the oscillator is enabled. Disabling the
oscillator saves battery/capacitor power during storage.
Calibration
Sign
Determines if the calibration adjustment is applied as an addition (1) to or as a subtraction (0) from the time-base.
Calibration
These five bits control the calibration of the clock.
Document #: 001-52039 Rev. **
Page 18 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Register Map Detail (continued)
Watchdog Timer
D4 D3
0x1FFF7
D7
D6
D5
D2
D1
D0
WDS
WDW
WDT
WDS
Watchdog Strobe. Setting this bit to 1 reloads and restarts the watchdog timer. The bit is cleared automatically
once the watchdog timer is reset. The WDS bit is write only. Reading it always will return a 0.
WDW
Watchdog Write Enable. Set this bit to 1 to disable writing of the watchdog time-out value (WDT5-WDT0). This
allows the user to strobe the watchdog stobe bit without disturbing the time-out value. Set this bit to 0 to allow bits
5-0 to be written.
WDT
Watchdog time-out selection. The watchdog timer interval is selected by the 6-bit value in this register. It represents
a multiplier of the 32 Hz count (31.25 ms). The range of time-out values is 31.25 ms (a setting of 1) to 2 seconds
(setting of 3Fh). Setting the watchdog timer register to 0 disables the timer. These bits can be written only if the
WDW bit was cleared to 0 on a previous cycle.
Interrupt
0x1FFF6
D7
D6
D5
D4
D3
D2
D1
D0
WIE
AIE
PFIE
ABE
H/L
P/L
0
0
WIE
AIE
Watchdog Interrupt Enable. When set to 1 and a watchdog time-out occurs, the watchdog timer drives the INT pin
as well as setting the WDF flag. When set to 0, the watchdog time-out only sets the WDF flag.
Alarm Interrupt Enable. When set to 1, the alarm match drives the INT pin as well as setting the AF flag. When set
to 0, the alarm match only affects the AF flag.
PFIE
Power-Fail Enable. When set to 1, a power failure drives the INT pin as well as setting the PF flag. When set to 0,
the power failure only sets the PF flag.
0
Reserved For Future Used
H/L
P/L
High/Low. When set to a 1, the INT pin is driven active high. When set to 0, the INT pin is open drain, active low.
Pulse/Level. When set to a 1, the INT pin is driven active (determined by H/L) by an interrupt source for approxi-
mately 200 ms. When set to a 0, the INT pin is driven to an active level (as set by H/L) until the Flags register is read.
Alarm – Day
0x1FFF5
D7
D6
D5
D4
D3
D2
D1
Alarm Date
D0
M
0
10s Alarm Date
Contains the alarm value for the date of the month and the mask bit to select or deselect the date value.
M
Match. Setting this bit to 0 causes the date value to be used in the alarm match. Setting this bit to 1 causes the
match circuit to ignore the date value.
Alarm – Hours
0x1FFF4
D7
D6
D5
D4
D3
D2
D1
D0
M
0
10s Alarm Hours
Alarm Hours
Contains the alarm value for the hours and the mask bit to select or deselect the hours value.
M
Match. Setting this bit to 0 causes the hours value to be used in the alarm match. Setting this bit to 1 causes the
match circuit to ignore the hours value.
Alarm – Hours
0x1FFF4
D7
D6
D5
D4
D3
D2
D1
D0
M
0
10s Alarm Hours
Alarm Hours
Contains the alarm value for the hours and the mask bit to select or deselect the hours value.
M
Match. Setting this bit to 0 causes the hours value to be used in the alarm match. Setting this bit to 1 causes the
match circuit to ignore the hours value.
Document #: 001-52039 Rev. **
Page 19 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Register Map Detail (continued)
Alarm – Seconds
D4 D3
0x1FFF2
D7
D6
D5
D2
D1
D0
M
10s Alarm Seconds
Alarm Seconds
Contains the alarm value for the seconds and the mask bit to select or deselect the seconds’ value.
M
Match. Setting this bit to 0 causes the seconds’ value to be used in the alarm match. Setting this bit to 1 causes
the match circuit to ignore the seconds value.
0x1FFF1
Real Time Clock – Centuries
D7
D6
D5
D4
D3
D2
D1
D0
10s Centuries
Centuries
Contains the BCD value of centuries. Lower nibble contains the lower digit and operates from 0 to 9; upper nibble
contains the upper digit and operates from 0 to 9. The range for the register is 0-99 centuries.
Flags
0x1FFF0
D7
D6
D5
D4
D3
D2
D1
D0
WDF
AF
PF
OSCF
0
CAL
W
R
WDF
Watchdog Timer Flag. This read-only bit is set to 1 when the watchdog timer is allowed to reach 0 without being
reset by the user. It is cleared to 0 when the Flags register is read or on power-up.
AF
Alarm Flag. This read-only bit is set to 1 when the time and date match the values stored in the alarm registers
with the match bits = 0. It is cleared when the Flags register is read or on power-up.
PF
Power-fail Flag. This read-only bit is set to 1 when power falls below the power-fail threshold V
to 0 when the Flags register is read or on power-up.
. It is cleared
SWITCH
OSCF
Oscillator Fail Flag. Set to 1 on power-up only if the oscillator is enabled and not running in the first 5ms of operation.
This indicates that RTC backup power failed and clock value is no longer valid. The user must reset this bit to 0
to clear this condition.
CAL
W
Calibration Mode. When set to 1, a 512Hz square wave is output on the INT pin. When set to 0, the INT pin resumes
normal operation. This bit defaults to 0 (disabled) on power up.
Write Enable. Setting the W bit to 1 freezes updates of the RTC registers and enables writes to RTC registers,
Alarm registers, Calibration register, Interrupt register and Flags register. Setting the W bit to 0 causes the contents
of the RTC registers to be transferred to the timekeeping counters if the time has been changed (a new base time
is loaded). This bit defaults to 0 on power up.
R
Read Time. Set R to 1 to captures the current time in holding registers so that clock updates are not seen during
the reading process. Set R to 0 to enable the holding register to resume clock updates. This bit defaults to 0 on
power up.
Document #: 001-52039 Rev. **
Page 20 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Ordering Information
STK17TA8-R F 45 ITR
Packing Option
Blank=Tube
TR=Tape and Reel
Temperature Range
Blank=Commercial (0 to +70 C)
I= Industrial (-45 to +85 C)
Access Time
25=25 ns
45=45 ns
Lead Finish
F=100% Sn (Matte Tin) RoHS Compliant
Package
R=Plastic 48-pin 300 mil SSOP (25 mil pitch)
Ordering Codes
Access Times
(ns)
Ordering Code
Description
Temperature
STK17TA8-RF25
STK17TA8-RF45
3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
25
45
25
45
25
45
25
45
Commercial
Commercial
Commercial
Commercial
Industrial
STK17TA8-RF25TR 3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
STK17TA8-RF45TR 3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
STK17TA8-RF25I
STK17TA8-RF45I
3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
Industrial
STK17TA8-RF25ITR 3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
STK17TA8-RF45ITR 3V 128Kx8 AutoStore nvSRAM+RTC SSOP48-300
Industrial
Industrial
Document #: 001-52039 Rev. **
Page 21 of 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STK17TA8
Document History Page
Document Title: STK17TA8 128k X 8 AutoStore™ nvSRAM with Real Time Clock
Document Number: 001-52039
Orig. of
Change
Submission
Date
Rev. ECN No.
**
Description of Change
2668660 GVCH/PYRS
03/04/2009
New Data Sheet
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at cypress.com/sales.
Products
PSoC
PSoC Solutions
General
Clocks & Buffers
Wireless
Low Power/Low Voltage
Precision Analog
LCD Drive
Memories
Image Sensors
CAN 2.0b
USB
© Cypress Semiconductor Corporation, 2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any
circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical,
life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without
the express written permission of Cypress.
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer
assumes all risk of such use and in doing so indemnifies Cypress against all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
Document #: 001-52039 Rev. **
Revised March 02, 2009
Page 23 of 23
AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document are the trademarks of their respective
holders.
Download from Www.Somanuals.com. All Manuals Search And Download.
|