Owner’s Manual
8-in. Wheel
3/4 Horsepower (continuous duty)
3450 R.P.M. (no load speed)
8-in. BENCH
GRINDER
Model No.
152.220180
10-in. Wheel
1 Horsepower (continuous duty)
1725 R.P.M. (no load speed)
10-in. BENCH
GRINDER
Model No.
152.220600
Customer Helpline
CAUTION:
FOR YOUR OWN SAFETY; Read and follow
1-800-897-7709
®
all of the Safety and Operating Instructions
before Operating this Bench Grinder
Please have your Model No.
and Serial No. available.
C
US
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Part No. OR94750
Español pg. 19
Download from Www.Somanuals.com. All Manuals Search And Download.
!
WARNING
To avoid electrical shock to yourself and damage to the
Bench Grinder, use proper circuit protection.
and use a 15 amp time delay fuse or circuit breaker.
The electrical circuit cannot have any wire size less
than #14. To avoid shock or fire, replace power cord
immediately if it is damaged in any way.
The Bench Grinder is factory wired for 120V, 60 Hz,
operation. Connect to a 120V, 15 amp branch circuit
SAFETY INSTRUCTIONS
8. WEAR PROPER CLOTHING. DO NOT wear loose
clothing, gloves, neckties, or jewelry. These items
can get caught in the machine during operations
and pull the operator into the moving parts. The
user must wear a protective cover on their hair, if
the hair is long, to prevent it from contacting any
moving parts.
GENERAL SAFETY INSTRUCTIONS
Operating a Bench Grinder can be dangerous if safety
and common sense are ignored. The operator must be
familiar with the operation of the tool. Read this manual
to understand this Bench Grinder. DO NOT operate this
Bench Grinder if you do not fully understand the limita-
tions of this tool. DO NOT modify this Bench Grinder in
any way.
9. ALWAYS WEAR EYE PROTECTION. Any power
tool can throw debris into the eyes during opera-
tions, which could cause severe and permanent
eye damage. ALWAYS wear Safety Goggles (that
comply with ANSI standard Z87.1) when operating
power tools. Safety Goggles are available at Sears
Retail Stores.
BEFORE USING THE BENCH GRINDER
!
WARNING
To avoid serious injury and damage to the tool, read
and follow all of the Safety and Operating Instructions
before operating the Bench Grinder.
1. READ the entire Owner’s Manual. LEARN how to
use the tool for its intended applications.
10. WEAR A DUST MASK TO PREVENT INHALING
2. GROUND ALL TOOLS. If the tool is supplied with a
3-prong plug, it must be plugged into a 3-contact
electrical receptacle. The 3rd prong is used to
ground the tool and provide protection against
accidental electric shock. DO NOT remove the 3rd
prong. See Grounding Instructions on page 5.
DANGEROUS DUST OR PARTICLES.
11. ALWAYS UNPLUG THE TOOL FROM THE ELEC-
TRICAL RECEPTACLE when making adjustments,
changing parts or performing any maintenance.
12. KEEP PROTECTIVE GUARDS IN PLACE AND IN
WORKING ORDER.
3. AVOID A DANGEROUS WORKING ENVIRON-
MENT. DO NOT use electrical tools in a damp
environment or expose them to rain.
13. AVOID ACCIDENTAL STARTING. Make sure that
the power switch is in the “OFF” position before
plugging in the power cord to the electrical
receptacle.
4. DO NOT use electrical tools in the presence of
flammable liquids or gasses.
5. ALWAYS keep the work area clean, well lit, and
organized. DO NOT work in an environment with
floor surfaces that are slippery from debris, grease,
and wax.
14. REMOVE ALL MAINTENANCE TOOLS from the
immediate area prior to turning “ON” the Bench
Grinder.
15. USE ONLY RECOMMENDED ACCESSORIES.
Use of incorrect or improper accessories could
cause serious injury to the operator and cause
damage to the tool. If in doubt, check the instruction
manual that comes with that particular accessory.
6. KEEP VISITORS AND CHILDREN AWAY. DO NOT
permit people to be in the immediate work area,
especially when the electrical tool is operating.
7. DO NOT FORCE THE TOOL to perform an opera-
tion for which it was not designed. It will do a safer
and higher quality job by only performing operations
for which the tool was intended.
16. NEVER LEAVE A RUNNING TOOL UNATTENDED.
Turn the power switch to the “OFF” position. DO
NOT leave the tool until it has come to a complete
stop.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS (cont.)
17. DO NOT STAND ON A TOOL. Serious injury could
26. CALIFORNIA PROPOSITION 65
result if the tool tips over or you accidentally contact
the tool.
SOME DUST CREATED BY POWER SANDING,
SAWING, GRINDING, DRILLING AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals
known to cause cancer, birth defects or other repro-
ductive harm.
18. DO NOT store anything above or near the tool
where anyone might try to stand on the tool to
reach it.
19. MAINTAIN YOUR BALANCE. DO NOT extend
yourself over the tool. Wear oil resistant rubbersoled
shoes. Keep floor clear of debris, grease, and wax.
GUIDELINES FOR
EXTENSION CORDS
20. MAINTAIN TOOLS WITH CARE. Always keep tools
clean and in good working order. Keep all blades
and tool bits sharp.
If you are using an extension cord outdoors, be sure
it is marked with the suffix “W-A” (“W” in Canada) to
indicate that it is acceptable for outdoor use.
21. EACH AND EVERY TIME, CHECK FOR DAMAGED
PARTS PRIOR TO USING THE TOOL. Carefully
check all guards to see that they operate properly,
are not damaged, and perform their intended func-
tions. Check for alignment, binding or breaking of
moving parts. A guard or other part that is damaged
should be immediately repaired or replaced.
Be sure your extension cord is properly sized, and
in good electrical condition. Always replace a damaged
extension cord or have it repaired by a qualified person
before using it.
22. CHILDPROOF THE WORKSHOP AREA by remov-
ing switch keys, unplugging tools from the electrical
receptacles, and using padlocks.
Protect your extension cords from sharp objects,
excessive heat, and damp or wet areas.
23. DO NOT OPERATE TOOL IF UNDER THE INFLU-
ENCE OF DRUGS OR ALCOHOL.
MINIMUM RECOMMENDED GAUGE FOR EXTENSION CORDS (AWG)
24. SECURE ALL WORK. When it is possible, use
clamps or jigs to secure the workpiece. This is
safer than attempting to hold the workpiece with
your hands.
120 VOLT OPERATION ONLY
25’ LONG
50’ LONG 100’ LONG 150’ LONG
0 to 6 Amps
6 to 10 Amps
10 to 12 Amps
18 AWG
18 AWG
16 AWG
16 AWG
16 AWG
16 AWG
16 AWG
14 AWG
14 AWG
14 AWG
12 AWG
12 AWG
25. USE A PROPER EXTENSION CORD IN GOOD
CONDITION. When using an extension cord, be
sure to use one heavy enough to carry the current
your product will draw. The table at right shows the
correct size to use depending on cord length and
nameplate amperage rating. If in doubt, use the
next heavier gauge. The smaller the gauge number,
the larger diameter of the extension cord. If in doubt
of the proper size of an extension cord, use a short-
er and thicker cord. An undersized cord will cause a
drop in line voltage resulting in a loss of power and
overheating. USE ONLY A 3-WIRE EXTENSION
CORD THAT HAS A 3-PRONG GROUNDING
PLUG AND A 3-POLE RECEPTACLE THAT
ACCEPTS THE TOOL’S PLUG.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING INSTRUCTIONS
IN THE EVENT OF A MALFUNCTION OR BREAK-
USE ONLY A 3-WIRE EXTENSION CORD THAT HAS
A 3-PRONG GROUNDING PLUG AND A 3-POLE
RECEPTACLE THAT ACCEPTS THE TOOL’S PLUG.
DOWN, grounding provides the path of least resistance
for electric current and reduces the risk of electric
shock. This tool is equipped with an electric cord that
has an equipment grounding conductor and a ground-
ing plug. The plug MUST be plugged into a matching
electrical receptacle that is properly installed and ground-
ed in accordance with ALL local codes and ordinances.
REPLACE A DAMAGED OR WORN CORD
IMMEDIATELY.
This tool is intended for use on a circuit that has an
electrical receptacle as shown in FIGURE A. FIGURE A
shows a 3-wire electrical plug and electrical receptacle
that has a grounding conductor. If a properly grounded
electrical receptacle is not available, an adapter as
shown in FIGURE B can be used to temporarily con-
nect this plug to a 2-contact ungrounded receptacle.
The adapter has a rigid lug extending from it that MUST
be connected to a permanent earth ground, such as a
properly grounded receptacle box. THIS ADAPTER IS
PROHIBITED IN CANADA.
DO NOT MODIFY THE PLUG PROVIDED. If it will not
fit the electrical receptacle, have the proper electrical
receptacle installed by a qualified electrician.
IMPROPER ELECTRICAL CONNECTION of the equip-
ment grounding conductor can result in risk of electric
shock. The conductor with the green insulation (with or
without yellow stripes) is the equipment grounding
conductor. DO NOT connect the equipment grounding
conductor to a live terminal if repair or replacement of
the electric cord or plug is necessary.
CAUTION: In all cases, make certain the electrical
receptacle in question is properly grounded. If you are
not sure have a certified electrician check the electrical
receptacle.
CHECK with a qualified electrician or service personnel
if you do not completely understand the grounding
instructions, or if you are not sure the tool is properly
grounded.
!
WARNING
This Bench Grinder is for indoor use only. Do not
expose to rain or use in damp locations.
Fig. A
Fig. B
grounding
adapter lug
3-prong
electrical receptacle
grounding
conductor
grounding
conductor
2-prong
electrical
receptacle
3-wire electrical cord
3-wire electrical cord
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. THE DIAMETER OF THE GRINDING WHEELS
WILL DECREASE WITH USE. Adjust the tool rests
and spark arrestors to maintain a distance of 1/16”
from the wheel.
SPECIFIC SAFETY INSTRUCTIONS
FOR BENCH GRINDERS
The operation of any grinder can result in debris being
thrown into your eyes, which can result in severe eye
damage. ALWAYS wear Safety Goggles (that comply
with ANSI standard Z87.1) when operating the grinder.
Safety Goggles are available at Sears Retail Stores.
Keep your thumbs and fingers away from the grinding
wheels.
4. DO NOT STAND IN FRONT OF THE BENCH
GRINDER WHEN STARTING IT. Stand to one side
of the Bench Grinder and turn it “ON”. Wait at the
side for one minute until the grinder comes up to
full speed. There is always a possibility that debris
from a damaged grinding wheel may be discharged
towards the operator.
5. THE BENCH GRINDER WILL PRODUCE SPARKS
AND DEBRIS DURING GRINDING OPERATIONS.
Be sure that there are not any flammable materials
in the vicinity. Frequently clean grinding dust from
the back of the Bench Grinder.
1. ALWAYS USE THE EYE SHIELDS AND WHEEL
GUARDS provided with the grinder.
2. REPLACE A CRACKED OR DAMAGED GRIND-
ING WHEEL IMMEDIATELY. A damaged wheel can
discharge debris at a high velocity towards the
operator. Carefully handle the grinding wheels since
they are abrasive. Prior to replacing a grinding
wheel, check it for cracks. DO NOT remove the
blotter or label on both sides of the grinding wheel.
Tighten the spindle nut just enough to hold the
grinding wheel firmly to the Bench Grinder. Do not
over-tighten the nut. Excessive clamping force can
damage the grinding wheel. Only use the wheel
flanges provided with the grinder. When selecting a
replacement grinding wheel, verify that the grinding
wheel has a higher R.P.M. rating than the maximum
R.P.M. of the Bench Grinder.
6. NEVER FORCE THE WORKPIECE AGAINST A
GRINDING WHEEL, especially if the wheel is cold.
Apply the workpiece slowly, allowing the grinding
wheel an opportunity to warm up. This will minimize
the chance of wheel breakage. DO NOT grind using
the sides of the grinding wheels. DO NOT apply
coolant directly to the grinding wheel.
7. KEEP ALL WHEEL GUARDS IN PLACE. DO NOT
USE THE BENCH GRINDER WITH THE WHEEL
GUARDS REMOVED.
8. KEEP THE TOOL RESTS FIRMLY TIGHTENED.
9. ALWAYS USE THE SUPPLIED WHEEL DRESSER
TO RESURFACE THE FACE OF THE GRINDING
WHEEL.
ACCESSORIES AND ATTACHMENTS
Sears may recommend other accessories not listed in
this manual.
AVAILABLE ACCESSORIES
Visit your Sears Hardware Department or see the
Sears Power and Hand Tool Catalog for the following
accessories.
See your nearest Sears Hardware Department or Sears
Power and Hand Tool Catalog for other accessories.
ITEM
STOCK NUMBER
See catalog or store
See catalog or store
See catalog or store
See catalog or store
See catalog or store
Do not use any accessory unless you have completely
read the Owner’s Manual for that accessory.
Replacement grinding wheels
Wire and Buffing wheels
Spacers
!
WARNING
Wheel dressers
Stand
Use only accessories recommended for this Bench
Grinder. Using other accessories may cause serious
injury and cause damage to the Bench Grinder.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
Bench Grinder can only be turned “ON” after all the
parts have been obtained and installed correctly.
UNPACKING AND CHECKING
CONTENTS (Fig. C)
This Bench Grinder will require a minimal amount of
assembly. A 10mm and 13mm open end wrench is
provided for mounting the Tool Rest Assemblies and
the Spark Arrestor Assemblies.
The following items are to be provided in the shipping
box:
A. Grinder
B. Quench tray
Remove all of the parts from the shipping box and lay
them on a clean work surface. Compare the items to
Fig. C, verify that all items are accounted for before
discarding the shipping box.
C. Wheel dresser
D. Eyeshield assembly
E. Left tool rest assembly (not shown)
F. Right tool rest assembly
G. Special Wrench
!
WARNING
If any parts are missing, do not attempt to plug in the
power cord and turn “ON” the Bench Grinder. The
Fig. C
A
D
F
B
C
G
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KNOW YOUR BENCH GRINDER
6
7
4
3
1
5
10B
9
10A
2
11
8
14
13
1. WHEEL GUARD - Covers the grinding wheels and
10. B) GRINDING WHEEL 60 GRIT - Used to remove
protects against accidental contact.
heavy material from workpiece.
2. WHEEL COVER - Covers the grinding wheels and
11. ON / OFF SWITCH - Used to turn “ON” and turn
provides access for routine maintenance.
“OFF” the grinder.
3. MOTOR HOUSING - Contains the electrical motor.
4. EYESHIELD MOUNTS - Supports the eyeshields.
12. WHEEL DRESSER - Used to clean and smooth
surface of the 8" Grinding Wheel (not shown).
13. QUENCH TRAY - Used to cool workpiece after
5. EYESHIELDS - Protective Lexan see-thru shields
to prevent any loose debris from contacting the
operator.
grinding.
14. MOUNTING PAD - Used to secure the grinder to a
workbench or suitable work surface.
6. FLEXIBLE WORK LIGHT - Provides assistance to
the operator for grinding operations.
15. GRINDING WHEEL IDENTIFICATION LABEL -
Provides information on wheel size, grit and maxi-
mum RPM. Must be left on to distribute the load of
tightening the Lock Nuts (not shown).
7. SPARK ARRESTORS - Prevents hot sparks and
debris from contacting the operator.
8. TOOL REST ADJUSTABLE SUPPORTS - Lets the
operator position the tool rest closer to the wheel as
the wheel decreases in diameter due to wear.
16. ARBOR BUSHING - Used when wheels have an
oversized wheel bore (not shown).
17. FLANGES - Used to secure the grinding wheels to
the grinder and distribute the load of the Lock Nuts
(not shown).
9. TOOL RESTS - Used to support the workpiece
that is being ground. Adjustable to provide angled
surfaces.
18. LOCK NUT - Used to secure the grinding wheels to
10. A) GRINDING WHEEL 120 GRIT - Used to remove
the grinder (not shown).
light material from workpiece.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY INSTRUCTIONS
A 10mm and 13mm open-end wrench (included) is
required for assembly of the Tool Rest Assemblies and
the Spark Arrestor Assemblies.
Fig. E
!
WARNING
• DO NOT assemble the Bench Grinder until you are
sure the tool IS NOT plugged in.
E
• DO NOT assemble the Bench Grinder until you are
sure the power switch is in the “OFF” position.
H
F
• DO NOT assemble the Bench Grinder until you are
sure the grinding wheels are firmly tightened to the
Bench Grinder.
G
TOOL RESTS (Figs. D and E)
The Bench Grinder is provided with two different Tool
Rest assemblies. The Left Side Tool Rest is entirely flat.
The Right Side Tool Rest is also flat, but has an acces-
sory plate for sharpening drill bits.
4. Adjust the Tool Rests until they are 1/16” from the
grinding wheels. Firmly tighten the hex head screws
holding the supports.
1. Remove both Tool Rest Assemblies from the plastic
bags and check to see that you have the following:
Left Side Tool Rest
Left Side Tool Rest Support
Right Side Tool Rest
Right Side Tool Rest Support Drill Bit Sharpening
Plate M8 Flat Washer (qty. 6)
M8 x 12mm Hex head screw (qty. 4)
Adjustment Knob (qty. 2)
SPARK ARRESTORS (Fig. F)
1. Remove both Spark Arrestor Assemblies from the
plastic bags and check to see that you have the
following:
Left Side Spark Arrestor
Right Side Spark Arrestor
2. Assemble the Tool Rest Supports (A) to the inside
surface of the Wheel Covers (B) with the flat wash-
ers (C) and hex head screws (D) as shown. See
Fig. D.
M6 Flat Washer (2)
M6 X 6mm Hex head screw (2)
2. Assemble the Spark Arrestors (A) to the inside sur-
face of the Wheel Covers (B) with the flat washers
(C) and hex head screws (D) as shown. See Fig. F.
3. Assemble the Tool Rests (E) to the Supports (F)
with the flat washers (G) and Adjustment Knobs (H)
as shown. See Fig. E.
3. Adjust the Spark Arrestors until they are 1/16" from
the grinding wheels. Firmly tighten the hex head
screws.
Fig. D
Fig. F
B
B
A
C
D
C
A
D
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EYE SHIELDS (Fig. G)
WORK LIGHT (Fig. H)
The Bench Grinder is provided with a Flexible Work
Light to assist in visibility of the workpiece.
1. Remove both Eye Shield Assemblies from the plas-
tic bags and check to see that you have the follow-
ing. Eyeshield (qty. 2) Lock Knob (qty. 2) Spacer
(qty. 2) M6 Flat washer (qty. 2) M6 x 80mm carriage
head screw (qty. 2)
The Bench Grinder is NOT provided with a light bulb for
the Flexible Work Light.
!
WARNING
2. Assemble the Eyeshield (C) to the Spark Arrestor
(A) by inserting the carriage head screw (B) through
Eyeshield (C), Spark Arrestor (A), and the spacer
(D) as shown.
To reduce the risk of fire, use a 120V, 40 watt Type A or
smaller bulb, medium base. DO NOT use a light bulb
that extends past the end of the light housing.
The Flexible Work Light (A) may be turned “ON” or
“OFF” by using the rotary switch (B) on the top surface
of the housing. The switch can be rotated in the clock-
wise direction only.
3. Assemble the flat washer (E) and Lock Knob (F) to
the carriage head screw and tighten until the
Eyeshield remains in the desired position.
NOTE: The Flexible Work Light can be turned “ON” or
“OFF” even if the Bench Grinder is turned “OFF”.
Fig. G
D
B
CAUTION: The Flexible Work Light housing will remain
hot for a few minutes after turning it “OFF”. Avoid con-
tact with housing until it is cool.
E
Fig. H
B
C
A
A
F
QUENCH TRAY
1. The Quench Tray is provided to cool the workpiece
during and after grinding operations.
2. Attach the Quench Tray to base of the Bench
Grinder as shown.
3. Tighten the two screws.
PERMANENT MOUNTING
You should firmly attach the Bench Grinder to a solid work
surface or heavy-duty stand (hardware not included).
4. Partially fill the Quench Tray with water. DO NOT
overfill! DO NOT use any other liquid in the Quench
Tray other than water.
5. Place the workpiece into the water after performing
the grinding operation to cool it.
!
WARNING
6. DO NOT put any water directly onto the grinding
If the Bench Grinder is not securely mounted, it will
have the ability to move or tip over during grinding
operations and possibly cause the operator’s fingers to
contact the grinding wheels.
wheels.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING THE BENCH GRINDER
USING THE WHEEL DRESSER (Fig. J)
The Bench Grinder is designed for hand held grinding,
sharpening, and cleaning operations.
Fig. J
ALWAYS WEAR EYE PROTECTION! Hot sparks are
produced during grinding operations.
1. The Power Switch must be in the “OFF” position.
2. Stand to the side of the Bench Grinder and plug in
the power cord to the correct power source.
3. Remain to the side of the Bench Grinder and turn it
“ON” by moving the power switch to the up position.
4. Allow the grinding wheels to come up to a steady
speed for at least one minute.
C
B
A
5. The Flexible Work Light may be turned “ON” if
desired.
The Wheel Dresser is to be used on the grinding
wheels. It will remove buildup of material on the grind-
ing wheel, remove imperfections and make the corners
of the grinding wheel square. See Fig. J.
6. Adjust the eyeshields. Place the workpiece on the
appropriate tool rest for the desired operation.
7. Move the workpiece towards the grinding wheel
until it lightly touches. Move the workpiece back
and forth across the front surface of the grinding
wheel removing the amount of material desired.
DO NOT EVER GRIND ON THE SIDES OF THE
GRINDING WHEELS.
1. Loosen the correct side tool rest (A) and adjust it
until it is in the flat horizontal position as shown and
1/16” away from the grinding wheel.
2. Turn “ON” the Bench Grinder. Let the grinding
wheel come up to a steady speed for one minute.
8. The operator may place the hot end of the work-
piece into the water in the quench tray to cool it.
3. After the grinding wheel has gotten to a steady
speed, place the Wheel Dresser (B) flat on the Tool
Rest with the serrated wheels facing the grinding
wheel.
9. After completing the grinding operations, turn “OFF”
the Bench Grinder by pushing down on the Power
Switch. CAUTION: It will take a few minutes for the
grinding wheels to come to a complete stop.
4. Firmly hold on to the handle of the Wheel Dresser.
10. Turn “OFF” the Flexible Work Light. CAUTION: The
Flexible Work Light housing will remain hot for a
few minutes after turning it “OFF”.
5. Move the Wheel Dresser forward until the serrated
wheels make light contact with the grinding wheel
(C). After contact has been made, slide the Wheel
Dresser side to side across the Tool Rest to dress
the grinding wheel until the edge of the grinding
wheel is square and the surface is clean.
11. Avoid contact with housing until it is cool. Unplug
the Bench Grinder from the power source.
6. After the operator has completed dressing the
grinding wheel, turn “OFF” the Bench Grinder and
let the grinding wheel come to a complete stop.
7. Inspect the grinding wheel for any damage!
8. The grinding wheel may now be slightly smaller in
diameter after dressing. Readjust the tool rests and
spark arrestors to maintain a 1/16” clearance to the
grinding wheel.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE GRINDING WHEEL (Fig. K)
D
Fig. K
C
J
F
K
B
I
A
G
H
E
Due to normal wear, both wheels will need to be
replaced occasionally. See Fig. K.
8. CAUTION: The new abrasive wheel to be put on
the Bench Grinder must have a higher R.P.M rating
than the Bench Grinder. The label on the side of the
abrasive wheels must stay on, DO NOT remove
this label.
1. Turn the power switch “OFF” and unplug the power
cord from its power source
2. Rotate the eyeshields to the “UP” position for
access to the tool rests.
9. Replace the abrasive wheel, outer wheel flange,
and the lock-nut in reverse order from removal.
3. Remove the three screws (A), flat washers (B),
external tooth lock washers (C) and nuts (D) hold-
ing the Outer Wheel Covers (E) to the Bench
Grinder.
CAUTION: DO NOT OVER-TIGHTEN the lock nut as
this may damage the abrasive wheels and cause seri-
ous injury to the operator.
4. Remove the Outer Wheel Covers.
5. Place a small wooden wedge between the Abrasive
Wheel (F) and Tool Rest (G) to prevent the wheels
from rotating.
DUST PORT (Fig. N)
6. Remove the right side grinding wheel by turning the
lock-nut (H) in the counterclockwise direction with
an open-end wrench (not included). The left side
wheel can be removed by turning the lock-nut in the
clockwise direction with an open-end wrench.
There is a dust port located on the inner side of each
Inner Wheel Guard. These dust ports allows the grind-
ing dust to exit the wheel cavity.
If you choose to attach the dust ports to a dust collec-
tion system, make sure the dust collector is rated and
configured for your grinding operation.
7. Remove the Outer Wheel Flange (I) and then
remove the abrasive wheel from the arbor shaft (J).
The Arbor Bushing (K) should be saved, for future
use, if the replacement wheel does not use this
bushing.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE OF THE BENCH GRINDER
CAUTION: REPLACE the abrasive wheels if there is
any damage at all. FAILURE to replace a damaged
!
WARNING
wheel can cause serious injury to the operator.
Turn the power switch “OFF” and unplug the power
cord from its power source prior to any maintenance.
CAUTION: DO NOT USE FLAMMABLE MATERIALS
to clean the Bench Grinder. A clean dry rag or brush is
all that is needed to remove dust and debris buildup.
LUBRICATION
The Bench Grinder has sealed lubricated bearings in
the motor housing that do not require any additional
lubrication from the operator.
!
WARNING
Repairs to the Bench Grinder should be performed by
trained personnel only. Contact your nearest Sears
Service Center for authorized service. Unauthorized
repairs or replacement with non-factory parts could
cause serious injury to the operator and damage to the
Bench Grinder.
CLEANING
With the Bench Grinder unplugged, rotate the abrasive
wheels slowly and inspect for any damage or trapped
shavings.
TROUBLESHOOTING
TO PREVENT INJURY TO YOURSELF or damage to the Bench Grinder, turn the switch to the “OFF” position and
unplug the power cord from the electrical receptacle before making any adjustments.
PROBLEM
LIKELY CAUSE(S)
SOLUTION
Motor does
not run
1. Machine not plugged in
2. Power switch in “OFF” position
3. Power cord is faulty
4. Fuse or circuit breaker are open
5. Damaged motor
1. Plug power cord into electrical receptacle
2. Lift switch to “ON” position
3. Return to Sears Service Center
4. Overloaded electrical circuit
5. Return to Sears Service Center
Motor does not
have full power
1. Incorrect line voltage
2. Damaged motor
1. Have a qualified electrician check line for proper voltage
2. Return to Sears Service Center
Motor runs hot
1. Motor is overloaded
1. Reduce pressure on workpiece
2. Poor air circulation around motor
2. Remove any blockage around motor
Motor stalls or
runs slow
1. Motor is overloaded
1. Reduce pressure on workpiece
2. Incorrect line voltage
3. Capacitor has failed
2. Have a qualified electrician check line for proper voltage
3. Return to Sears Service Center
Fuse blows or
circuit breaker
trips
1. Motor overloaded
1. Reduce pressure on workpiece
2. Reduce the amount of items on circuit
3. Replace with correct fuse or circuit breaker
4. Use correct size
2. Overloaded electrical circuit
3. Wrong fuse or circuit breaker
4. Undersized or excessive length of
extension cord, see manual
5. Grinding wheels are blocked
5. Unplug machine and remove obstruction
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
8-IN. PROFESSIONAL BENCH GRINDER PARTS LIST
MODEL NO. 152.220180
!
WARNING
When servicing, use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause
product damage.
!
WARNING
Any attempt to repair or replace electrical parts on this Bench Grinder may create a HAZARD unless repair is done
by a qualified service technician. Repair service is available at your nearest Sears Service Center.
Always order by PART NUMBER, not by key number.
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
DESCRIPTION
QTY.
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
OR90055
OR90152
OR90059
OR90001
OR90002
OR90488
OR90059
OR90530
OR90001
OR90059
OR90152
OR90055
OR90002
OR90489
OR90530
OR90059
OR90567
OR90059
OR94751
OR94170
OR90519
OR71420
M6x80mm CARRIAGE HD SCREW
EYESHIELD
M6mm FLAT WASHER
M6mm KNOB
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
1
1
1
53
OR94747
LEFT TOOL REST ASSY, CONST OF:
REF 54 TO REF 56E
LEFT TOOL REST SUPPORT
LEFT TOOL REST
5/16 FLAT WASHER
KNOB 5/16 - 18
M8 FLAT WASHER
M8 LOCK WASHER
M8 x 20mm HEX HEAD SCREW
RIGHT TOOL REST ASSY, CONST OF :
REF 58 TO REF 60E
RIGHT TOOL REST SUPPORT
RIGHT TOOL REST
1
1
1
1
1
2
2
2
54
55
OR90203
OR90204
OR90625
OR90155
OR90311
OR90248
OR93917
OR94748
56A
56B
56C
56D
56E
57
SPACER
SPARK ARRESTOR-L.H
M6mm FLAT WASHER
M6x10mm HEX HD SCREW
M6mm KNOB
M6mm FLAT WASHER
EYESHIELD
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
1
1
1
1
2
2
2
1
1
1
1
2
2
1
1
1
1
2
2
1
1
2
1
1
2
4
4
1
2
1
2
4
1
1
2
2
1
2
1
2
1
58
59
60A
60B
60C
60D
60E
63
64
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
OR90191
OR90192
OR90155
OR90625
OR93917
OR90248
OR90311
OR71428
OR90544
OR90227
OR90228
OR90507
OR90362
OR71429
OR71430
OR94758
OR71432
OR90248
OR90504
OR71433
OR71434
OR71435
OR90362
OR90507
OR90362
OR90863
OR71436
OR71437
OR90333
OR71438
OR90505
OR90362
OR71439
OR71424
OR90362
OR90507
OR71440
OR90507
OR90050
OR90510
OR94750
M6x80mm CARRIAGE HD SCREW
SPACER
KNOB 5/16 - 18
SPARK ARRESTOR-R.H
M6x10mm HEX HD SCREW
M6mm FLAT WASHER
PAN HD SCREW M6x60mm
M6mm FLAT WASHER
OUTER WHEEL GUARD-RH
HEX NUT M14
WHEEL FLANGE
GRINDING WHEEL,120 GRIT-
8" DIA x 1" WIDE x 1" BORE
5/16 FLAT WASHER
M8 x 20mm HEX HEAD SCREW
M8 LOCK WASHER
M8 FLAT WASHER
LIGHT ASSY, INCL:
LIGHT WARNING LABEL
M10mm LOCK WASHER
M10x1mm HEX NUT
PAN HD SCREW M5x8mm
M5 EXT TOOTH WASHER
CORD CLAMP
CLAMP PLATE
BASE
CORDSET
M8mm LOCK WASHER
HEX HD SCREW M8x18mm
CLAMP
CAPACITOR(150°F)
END CAP
M5 EXT TOOTH WASHER
PAN HD SCREW M5x6mm
M5 EXT TOOTH WASHER
PAN HD SCREW M5x12mm
PAD
BASE PLATE
M6x10mm HEX HD SCREW
WATER TRAY
1
1
1
4
4
1
1
3
3
3
1
1
1
3
3
3
1
1
4
4
1
23
24
25
26
27
28
29
30
31
33
34
36
38
39
40
41
42
43
44
45
46
OR90525
OR90519
OR90501
OR90502
OR94752
OR90526
OR90059
OR90235
OR90502
OR94753
OR94754
OR94755
OR90502
OR90235
OR90059
OR94756
OR90526
OR90502
OR91826
OR90519
OR90551
WHEEL BUSHING
WHEEL FLANGE
PAN HD SCREW M6x16mm
M6mm LOCK WASHER
INNER WHEEL GUARD ASSEMBLY-RIGHT, INCL:
ROTATION LABEL
M6mm FLAT WASHER
HEX NUT M6
M6mm LOCK WASHER
MOTOR ASSEMBLY, INCL: REF 34 & REF 36
NAME PLATE LABEL
SPEC LABEL
M6mm LOCK WASHER
HEX NUT M6
M6mm FLAT WASHER
INNER WHEEL GUARD ASSEMBLY-LEFT, INCL:
ROTATION LABEL
M6mm LOCK WASHER
PAN HD SCREW M6x16mm
WHEEL FLANGE
PAN HD SCREW M5x12mm
M5 EXT TOOTH WASHER
SWITCH
GRINDING WHEEL, 60 GRIT -
8" DIA x 1" WIDE x 1" BORE
WHEEL BUSHING
1
1
1
1
1
3
3
SWITCH PLATE
47
48
49
50
51
52
OR90525
OR90519
OR90498
OR94757
OR90059
OR90567
M5 EXT TOOTH WASHER
PAN HD SCREW M5x8mm
DIAMOND WHEEL DRESSER
PAN HD SCREW M5x8mm
10mm x 12mm OPEN END WRENCH (NOT SHOWN)
BEARING (NOT SHOWN)
OWNERS MANUAL (NOT SHOWN)
WHEEL FLANGE
HEX NUT M14-LEFT HAND
OUTER WHEEL GUARD-LH
M6mm FLAT WASHER
PAN HD SCREW M6x60mm
14
Download from Www.Somanuals.com. All Manuals Search And Download.
8-IN. PROFESSIONAL BENCH GRINDER PARTS LIST
MODEL NO. 152.220180
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
10-IN. PROFESSIONAL BENCH GRINDER PARTS LIST
MODEL NO. 152.220600
!
WARNING
When servicing, use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause
product damage.
!
WARNING
Any attempt to repair or replace electrical parts on this Bench Grinder may create a HAZARD unless repair is done
by a qualified service technician. Repair service is available at your nearest Sears Service Center.
Always order by PART NUMBER, not by key number.
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
DESCRIPTION
QTY.
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
OR90055
OR90152
OR90059
OR90001
OR90002
OR90488
OR90059
OR90333
OR90001
OR90059
OR90152
OR90055
OR90002
OR90489
OR90333
OR90059
OR90567
OR90059
OR94740
OR90499
OR71446
OR71447
M6x80mm CARRIAGE HD SCREW
EYESHIELD
M6mm FLAT WASHER
M6mm KNOB
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
3
1
1
1
53
OR94747
LEFT TOOL REST ASSY, CONST OF:
REF 54 TO REF 56E
LEFT TOOL REST SUPPORT
LEFT TOOL REST
5/16 FLAT WASHER
KNOB 5/16 - 18
M8 FLAT WASHER
M8 LOCK WASHER
M8 x 20mm HEX HEAD SCREW
RIGHT TOOL REST ASSY, CONST OF :
REF 58 TO REF 60E
RIGHT TOOL REST SUPPORT
RIGHT TOOL REST
1
1
1
1
1
2
2
2
54
55
OR90203
OR90204
OR90625
OR90155
OR90311
OR90248
OR93917
OR94748
56A
56B
56C
56D
56E
57
SPACER
SPARK ARRESTOR-L.H
M6mm FLAT WASHER
M6x12mm HEX HD SCREW
M6mm KNOB
M6mm FLAT WASHER
EYESHIELD
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
1
1
1
1
2
2
2
1
1
1
1
2
2
1
1
1
1
2
2
1
1
2
1
1
2
4
4
1
2
1
2
4
1
1
2
2
1
2
1
2
1
58
59
60A
60B
60C
60D
60E
63
64
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
OR90191
OR90192
OR90155
OR90625
OR93917
OR90248
OR90311
OR71428
OR90544
OR90227
OR90228
OR90507
OR90362
OR71429
OR71430
OR94749
OR71454
OR90248
OR90504
OR71455
OR71456
OR71450
OR90362
OR90507
OR90362
OR90863
OR71436
OR71437
OR90333
OR71438
OR90505
OR90362
OR71439
OR71424
OR90362
OR90507
OR71440
OR90507
OR90050
OR90510
OR94750
M6x80mm CARRIAGE HD SCREW
SPACER
KNOB 5/16 - 18
SPARK ARRESTOR-R.H
M6x12mm HEX HD SCREW
M6mm FLAT WASHER
PAN HD SCREW M6x60mm
M6mm FLAT WASHER
OUTER WHEEL GUARD-RH
HEX NUT M16
WHEEL FLANGE
GRINDING WHEEL, 120 GRIT-
10" DIA x 1" WIDE x 1-1/4" BORE
WHEEL BUSHING
WHEEL FLANGE
PAN HD SCREW M6x16mm
M6mm LOCK WASHER
INNER WHEEL GUARD ASSEMBLY-RIGHT, INCL:
REF 28
ROTATION LABEL
M6mm FLAT WASHER
HEX NUT M6
M6mm LOCK WASHER
MOTOR ASSEMBLY, INCL: REF 34 & REF 36
NAME PLATE LABEL
SPEC LABEL
M6mm LOCK WASHER
HEX NUT M6
5/16 FLAT WASHER
M8 x 20mm HEX HEAD SCREW
M8 LOCK WASHER
M8 FLAT WASHER
LIGHT ASSY, INCL:
LIGHT WARNING LABEL
M10mm LOCK WASHER
M10x1mm HEX NUT
PAN HD SCREW M5x8mm
M5 EXT TOOTH WASHER
CORD CLAMP
CLAMP PLATE
BASE
POWER CORD
M8mm LOCK WASHER
HEX HD SCREW M8x18mm
CLAMP
CAPACITOR(100°F)
END CAP
M5 EXT TOOTH WASHER
PAN HD SCREW M5x6mm
M5 EXT TOOTH WASHER
PAN HD SCREW M5x12mm
PAD
BASE PLATE
M6x10mm HEX HD SCREW
WATER TRAY
1
1
1
4
4
23
24
25
26
27
OR71448
OR71446
OR90501
OR90502
OR94741
1
1
3
3
3
1
1
1
3
3
3
28
29
30
31
33
34
36
38
39
40
41
OR90526
OR90059
OR90235
OR90502
OR94742
OR94743
OR94744
OR90502
OR90235
OR90059
OR94745
M6mm FLAT WASHER
INNER WHEEL GUARD ASSEMBLY-LEFT, INCL:
REF 42
1
1
4
4
1
42
43
44
45
46
OR90526
OR90502
OR91826
OR71446
OR90520
ROTATION LABEL
PAN HD SCREW M5x12mm
M5 EXT TOOTH WASHER
SWITCH
M6mm LOCK WASHER
PAN HD SCREW M6x16mm
WHEEL FLANGE
GRINDING WHEEL, 60 GRIT-
10" DIA x 1" WIDE x 1-1/4" BORE
WHEEL BUSHING
WHEEL FLANGE
HEX NUT M16-LEFT HAND
OUTER WHEEL GUARD-LH
M6mm FLAT WASHER
PAN HD SCREW M6x60mm
SWITCH PLATE
M5 EXT TOOTH WASHER
PAN HD SCREW M5x8mm
DIAMOND WHEEL DRESSER
PAN HD SCREW M5x8mm
10mm x 12mm OPEN END WRENCH (NOT SHOWN)
BEARING (NOT SHOWN)
OWNERS MANUAL (NOT SHOWN)
1
1
1
1
1
3
3
47
48
49
50
51
52
OR71448
OR71446
OR90500
OR94746
OR90059
OR90567
16
Download from Www.Somanuals.com. All Manuals Search And Download.
10-IN. PROFESSIONAL BENCH GRINDER PARTS LIST
MODEL NO. 152.220600
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Get it fixed, at your home or ours!
Your Home
For repair–in your home–of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call or go on-line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. only)
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada) on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
MC
1-800-LE-FOYER
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
Download from Www.Somanuals.com. All Manuals Search And Download.
|