™
/
Model 956D 3-Button Security✚® Mini Remote Control
OWNER'S MANUAL
The 900 Series remote control Security✚® works only with
315 MHz door openers and light controls having a purple
“learn” button and a yellow indicator light.
To prevent possible SERIOUS INJURY or DEATH from a moving
gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER
permit children to operate, or play with remote control
transmitters.
Programming instructions are described and illustrated
below. The additional push buttons can also activate other
garage door openers and/or light controls. (Instructions for
programming light products are included with those
accessories.)
• Activate gate or door ONLY when it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
NOTE: If using with a gate operator refer to gate operator
manual for programming instructions. Manuals are also
available on-line at chamberlain-diy.com.
• ALWAYS keep gate or garage door in sight until completely closed.
NEVER permit anyone to cross path of moving gate or door.
Instructions are described and illustrated below
The Remote Control Battery
9
1
9
1
7
3
7
3
5
5
KG
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 212°F (100°C ) or
incinerate.
1. Press and release the “learn” button on the
motor unit. The learn indicator light will
glow steadily for 30 seconds.
The 3V2032 lithium battery
should produce power for up to
5 years. To replace battery, use
the visor clip or screwdriver
blade to pry open the case as
shown. Insert battery positive
side up.
Dispose of old battery properly.
Replace the batteries with only
3V2032 coin cell batteries.
2. Within 30 seconds, press and hold the
button on the hand-held remote.
3. Release the button when the motor unit
light blinks. It has learned the code. If
light bulbs are not installed, two clicks will
be heard.
To Erase All Codes From Motor Unit Memory
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or modifications of
this receiver and/or transmitter are prohibited, except for changing the code setting or replacing
the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
To deactivate any unwanted remote, first erase all codes:
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Press and hold the “learn” button on motor
unit until the learn indicator light goes out
(approximately 6 seconds). All previous codes
are now erased. Reprogram each remote or
keyless entry you wish to use.
Replacement Parts
3V2032 Lithium Battery . . . . . . . . . . . . . . . . . . . . . . .10A20
Owner’s Manual – Spanish . . . . . . . . . . . . . . .114A3149SP
To Control the Opener Lights
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-528-9131
In addition to operating the door, you may program the remote
to operate the lights.
1. With the door closed, press and hold the remote button that
you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener lights
should turn on or off but the door should not move.
©2007, The Chamberlain Group, Inc.
All Rights Reserved
Download from Www.Somanuals.com. All Manuals Search And Download.
114A3149D
|