CARPET EXTRACTOR
Operating Instructions
MODEL:
CEXT7
10080360
Read these instructions before operating the machine
D
86037910 03/23/07
PRV NO. 980311
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log/Overview.........................1
Table of Contents..........................................2
HOW TO USE THIS MANUAL
How to use this Manual.................................1-1
SAFETY
Important Safety Instructions ........................2-1
Hazard Intensity Level ..................................2-2
Grounding Instructions..................................2-3
OPERATIONS
Technical Specifications. ..............................3-1
Controls/Component Location ......................3-2
Filling Operation............................................3-5
Operations. ...................................................3-6
Cleaning Procedure. .....................................3-8
Accessory Tool Usage................................ 3-10
MAINTENANCE
Service Schedule..............................……… 4-1
Periodic Maintenance. ..................................4-2
Daily/ Regular Maintenance..........................4-2
Vacuum Motor Replacement ........................4-3
Belt Replacement..........................................4-4
Solution Pump Replacement ............……… 4-5
Wiring Diagram. ............................................4-6
Troubleshooting Chart ..................................4-7
GROUP PARTS LIST
Frame Assembly......................................... 5-1
Brush Assembly.......................................... 5-3
Pump Assembly(prior to SN). ..................... 5-5
Pump Assembly.......................................... 5-7
Vacuum Shoe Assembly............................. 5-9
Control Panel Assembly.............................. 5-11
Solution Tank Assembly. ............................ 5-13
Recovery Tank Assembly. .......................... 5-15
Suggested Spare Parts/Notes .................... 5-17
86037910 CEXT7 03/23/07
2
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
The SAFETY section contains important information
regarding hazard or unsafe practices of the
machine. Levels of hazards is identified that could
result in product or personal injury, or severe injury
resulting in death.
This manual contains the following sections:
-
-
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine model
and machine serial number are important. Refer to
the MACHINE DATA box which is filled out during
the installation of your machine. The MACHINE
DATA box is located on the inside of the front cover
of this manual.
-
-
-
Periodic
Daily/Regular
Troubleshooting
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts
lists include a number of columns of information:
MODEL _____________________________________
DATE OF PURCHASE ________________________
SERIAL NUMBER ____________________________
SALES REPRESENTATIVE # ___________________
DEALER NAME ______________________________
OPERATIONS GUIDE NUMBER __________________
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
-
-
PRV NO. – reference number.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
PUBLISHED ________________________________
-
-
SERIAL NO. FROM – column indicates
the first machine the part number is
applicable to. When the machine design
has changed, this column will indicate
serial number of applicable machine.
The main illustration shows the most
current design of the machine. The
boxed illustrations show older designs.
If column has an asterisk (*), call
manufacturer for serial number.
The model and serial number of your machine is on
the bottom back-end of the machine.
-
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
86037910 CEXT7 03/23/07
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
This machine is for commercial use.
To reduce the risk of fire, electric shock, or injury:
WARNING:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or
service.
Use only indoors. Do not use outdoors or expose to rain.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the
machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp
edges or corners.
Do not run machine over cord. Keep cord away from heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
This machine is intended for cleaning carpet only.
Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
This machine is not suitable for picking up health endangering dust.
Turn off all controls before unplugging.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops
and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
If foam or liquid comes out of machine, switch off immediately.
SAVE THESE INSTRUCTIONS
86037910 CEXT7 03/23/07
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
HAZARD INTENSITY LEVEL
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
! WARNING
WARNING - Hazards or unsafe practices which COULD result in severe personal injury or death.
! CAUTION
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property
damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate
all safety devices on the machine. Please take the necessary steps to train the machine operating
personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use manufacturer approved replacement parts.
86037910 CEXT7 03/23/07
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
GROUNDING INSTRUCTIONS
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
Grounding Pin
ELECTRICAL:
GROUNDING CONNECTION
USING AN ADAPTOR
In the USA this machine operates on a standard 15
amp 115V, 60 hz, A.C. power circuit. The amp,
hertz, and voltage are listed on the data label found
on each machine. Using voltages above or below
those indicated on the data label will cause serious
damage to the motors.
Grounded
Outlet
Metal Screw
FIGURE A
Adaptor
Grounded
Outlet Box
EXTENSION CORDS:
Tab for Grounding
Screw
FIGURE B
If an extension cord is used, the wire size must be at
least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
Adaptor
FIGURE C
Note: Adaptors are not allowed in Canada.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to reduce
the risk of electric shock. This appliance is equipped
with a cord having an equipment-grounding
conductor and grounding plug. The plug must be
inserted into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified electrician
or service person if you are in doubt as to
whether the outlet is properly grounded. Do not
modify the plug provided with the appliance - if it
will not fit the outlet, have a proper outlet
installed by a qualified electrician.
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like the
plug in “Fig. A”. A temporary adaptor that looks like
the adaptor in “Fig. C” may be used to connect this
plug to a 2-pole receptacle as shown in “Fig. B”, if a
properly grounded outlet is not available. The
temporary adaptor should be used only until a
properly grounded outlet (Fig. A) can be installed by
a qualified electrician. The green colored rigid ear,
lug, or wire extending from the adaptor must be
connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the
adaptor is used, it must be held in place by a metal
screw.
86037910 CEXT7 03/23/07
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
POWER TYPE
GENERAL DIMENSIONS/WEIGHT
ELECTRICAL: 115 V, 15 A, 60 HZ
Vacuum shoe: 17” (43.18 cm) cast
aluminum with spring loaded down
pressure
ELECTRIC VACUUM MOTOR: (1) –3 stage, 1 hp, 99
cfm (2.80 cubic meters/min.) Waterlift –117” (297cm)
WHEELS: (2) 10” dia. (25 cm) wheels
BRUSH: (1) 15” (38.1 cm.)
by 2”
SOLUTION PUMP: Diaphragm style, internal bypass
SOLUTION CAPACITY: 7 gallons (26.5ltr)
RECOVERY CAPACITY: 7 gallons (26.5ltr)
BRUSH SPEED: 1000 rpm
WEIGHT: 92lbs. (42kg)
LENGTH: 41” (104 cm)
HEIGHT: 34” (86.36 cm)
WIDTH: 17.5” (44.45 cm)
SOLUTION SPRAY: 2 quick change
jets.
POWER CABLE: 50’ (12.7 m) (14
gauge)
34”
(86.36cm)
17.5”
(44.45cm)
41”
(104cm)
3-1
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS/COMPONENT LOCATIONS
1. Main Handle. Used to pull and maneuver
machine.
2. Electrical Cord.
3. Pump Switch. Turns on pump and enables
3
5
spray.
4. Brush/Spray switch. Turns on brush motor
and activates electro-valve to dispense solution
to floor through jets. Intermittent, off, and
continuous settings.
5. Vacuum Motor Switch. Turns on vacuum
motor
6. Brush Motor Circuit Breaker. 6 amp. Breaker
protecting brush motor.
4
1
7. Vacuum Motor Circuit Breaker. 15 amp.
Breaker protecting vacuum motor.
8. Recovery Dump Hose. Facilitates draining
7
6
dirty cleaning solution.
9. Solution Dump Hose. Facilitates draining
excess cleaning solution from solution tank.
2
8
9
86037910 CEXT7 03/23/07
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS/COMPONENT LOCATIONS
1. Solution Accessory Tool Hookup. Used for
various auxiliary cleaning tools.
2. Vacuum Hose Door. Used to connect various
auxiliary 1 ½ inch cleaning tool vacuum hoses.
3. Brush Height Adjustment. Used to regulate
brush height from storage position to various
carpet heights.
10
4. Recovery Tank. Used to collect dirty cleaning
solution.
5. Solution Tank. Used to hold cleaning solution.
6. Recovery Tank Dome.
7. Vacuum Shoe.
1
8. Brush Housing.
9
9. Front Lifting Handle.
2
3
10. Cleaning Solution Filter.
6
4
5
7
8
86037910 CEXT7 03/23/07
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS/COMPONENT LOCATIONS
1. Solution Intake Cover.
2. Vacuum Intake Cover.
3. Float Shut-Off.
4. Clean-Out Opening.
5. Pour Spout.
6. Lift Handle.
6
1
2
4
6
5
3
86037910 CEXT7 03/23/07
3-4
Download from Www.Somanuals.com. All Manuals Search And Download.
FILLING OPERATIONS
STEP
1
RECOVERY TANK
Remove recovery
tank
SOLUTION
TANK
STEP
Add water
2
7 gal.
(26.5 ltr.)
FILL LINE
140°F (60°C)
STEP
3
7 – 14oz.
(207ml – 414ml)
FILLING THE CADET
NOTE: Use clean bucket of water to fill solution tank
Add cleaning
chemical
Do not put defoamer, solvents, spotter or
prespray chemicals in the solution tank.
Do not allow water to spill into vacuum motor inlet.
Dry spillage from top of solution tank before
replacing recovery tank.
CHEMICALS
Suitable Chemicals
Alkalis
STEP
Non-Compatible Chemicals
Aldehydes
4
Detergents
Hydroxides
Soaps
Aromatic Hydrocarbons
SP Butyls
Carbon Tetrachloride
Clorox*
Replace recovery
tank
Vinegar
Chlorinated Bleaches
Chlorinated Hydrocarbons
Lysol*
Methyl Ethel Ketone (MEK)
Perchorethylene (perc)
Phenolics
Trichlorethylene
D-Limonene
86037910 CEXT7 03/23/07
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
STEP Remove electrical cord and literature from
1
recovery tank. Fill solution tank (see filling
operations, page3-5).
STEP Plug cord into grounded outlet.
2
Note: Be sure dome is seated on recovery
tank, and float shut-off is installed correctly.
STEP
Adjust brush to proper setting.
3
Note: For good operation the brush must
skim the carpet. If circuit breaker trips raise
brush to prevent damage to motor or carpet.
1/8in
(3mm)
CORRECT
INCORRECT
STEP
Turn on both Vacuum and Pump motor
switches (“ON”=“I”).
PUMP
VACUUM
4
ON
ON
86037910 CEXT7 03/23/07
3-6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
Tip machine back by main handle to move STEP
to starting point.
5
STEP
6
Lower machine to floor.
STEP
7
Select intermittent or continuous switch
setting to turn on brush and start solution
spray.
INTERMITTENT
The intermittent setting requires the
operator to hold the switch in the “on”
position with the thumb, and is typically
used in small areas where short cleaning
passes are made.
The continuous setting allows the operator
to set the switch in the “on” position with
one touch, and is typically used in large
areas where long cleaning passes are
made.
CONTINUOUS
86037910 CEXT7 03/23/07
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING PROCEDURE
Start at wall closest to power outlet. Pull
straight back without pushing down on
handle.
STEP
1
Release intermittent setting or turn off
continuous setting on brush/spray switch
approximately 1 foot before ending
cleaning pass.
STEP
2
1ft.
(30cm)
OFF
Push down on handle to raise vacuum
shoe and brush before moving to the next
cleaning pass. Overlap brush contact
area approximately 1inch.
STEP
1in.
(25mm)
3
During operation, observe the following: The
extractor is equipped with clear internal covers
to facilitate operator viewing of dirty solution and
vacuum air flow.
STEP
SOLUTION
INTAKE COVER
4
During operation, observe the vacuum intake
cover. Large amounts of water or foam entering
the vacuum system can damage the vacuum
motor. If you notice either condition, shut down
the machine immediately. Empty recovery
tank and/or add defoamer to recovery tank.
VACUUM
INTAKE COVER
86037910 CEXT7 03/23/07
3-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING PROCEDURE
Use right side of machine for cleaning
against walls.
STEP
5
After cleaning, turn off all controls, return
brush to storage position and carefully
unplug machine.
STEP
6
OFF
OFF
OFF
STEP
To speed drying, use a Windblower™ fan.
7
Empty recovery tank by releasing dump
hose. Use a hose with cold water to clean
out the recovery tank. Also drain solution
tank after each use.
STEP
8
RECOVERY
DRAIN
SOLUTION
DRAIN
86037910 CEXT7 03/23/07
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORY TOOL USAGE
STEP
Use only one of the following acceptable
accessory tools.
1
150-52 Hose Assembly
89226 Wand
380-29 Upholstery Tool
380-21 Crevice Tool
380-36A Auto Detail Tool
Pull back collar and insert over machine
mounted fitting, then release collar to lock
into place.
STEP
Lift door on front of vacuum shoe and insert
1 ½ inch hose cuff into hole.
2
STEP
Turn on Pump and Vacuum Switch. Note:
Be sure intermittent/continuous switch is in
center (off) position and brush is in storage
position.
PUMP
VACUUM
ON
3
ON
OFF
STEP
Squeeze handle on accessory tool to begin
cleaning.
4
86037910 CEXT7 03/23/07
3-10
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
Check machine for cord damage
DAILY
*
WEEKLY
QUARTERLY
Check recovery dome and gasket for
damage and cleanliness
Check brush – should be clean with no
lint or strings attached
Inspect vac shoe for blockage; remove
fibers with coat hanger, etc.
Check hoses for wear, blockages, or
damage
*
*
*
*
Check handles, switches, and knobs
for damage
Check vac motor intake filter and clean
*
*
Run one gallon of water through
system
*
*
*
*
*
*
Clean out recovery tank and check
float valve to make sure it moves freely
Clean out solution tank and remove
and clean vacuum intake screen
Clean outside of all tanks and check for
damage
Run vac motor for at least one minute
to allow motor to dry
Store with dome off tank to allow the
tank to dry
Check all bearings for noise
Check all gaskets for wear and leakage
*
*
Check vacuum intake screen for
damage; replace if necessary
Check pump pressure; observe spray
pattern and check with gauge if
necessary
*
*
*
Check and clean solution screen
Check belts for wear and replace as
necessary
*
Check brush for wear; ensure bristles
are not damaged
Check cables for fraying
*
*
Check the spray bar (manifold) for
damage; replace if broken or bent
Check condition of vac shoe and frame
for damage
*
*
*
Check overall performance of machine
Check vac motor carbon brushes
*
4-1
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PERIODIC MAINTENANCE
7. Remove lint and dirt build-up from brush and
housing.
Twice a month, flush a white vinegar solution (One
quart vinegar to two gallons of water) or anti-
browning solution (mixed as directed) through the
extractor. This will prevent build-up of alkaline
residue in the system. If spray jets become clogged,
remove the spray tips, wash them thoroughly, and
blow-dry.
NOTE: Brush removal.
A. To remove brush, grab and pull brush out
from end opposite drive belt (operator’s
right). Remove other end from brush driver.
B. To install brush, line up slots in brush core
with pin in driver on drive belt side
(operator’s left) and push brush onto driver.
Then snap bearing end (opposite end) of
brush into retaining clip.
NOTE: Do not use pins, wire, etc. to clean nozzles
as this could destroy spray pattern.
8. Check cooling air screen (located on frame
behind left wheel) for lint or debris.
9. Check float and shut-off screen and clean as
necessary.
Periodically inspect all hoses, electrical cables and
connections on your machine. Frayed or cracked
hoses should be repaired or replaced to eliminate
vacuum or solution pressure loss. If the cable
insulation is broken or frayed, repair or replace it
immediately. Don’t take chances with electrical fire
or shock.
NOTE: Always store machine with brush in “Store”
position.
DAILY / REGULAR MAINTENANCE
Before making any adjustments or repairs to the
machine, disconnect the power cord from electrical
source.
1. Empty unused cleaning solution from the
solution tank.
2. Inspect and clean filter screen in solution tank.
3. Flush pumping system with 4 or 7 liters of clean,
hot water.
4. After each use, rinse tank with fresh water.
Periodically inspect the recovery tank and
decontaminate if necessary, using a Hospital
Grade Virucide or a 1-10 bleach to water
solution. Waste water should be disposed of
properly.
5. Check for and remove any lint or debris around
vac shoe.
6. Check spray jets for full spray pattern.
86037910 CEXT7 03/23/07
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Vacuum Motor Carbon Brushes Replacement
ONLY QUALIFIED
MAINTENANCE
End Cap
WARNING:
PERSONNEL ARE TO
PERFORM THE FOLLOWING REPAIRS.
VACUUM MOTOR REPLACEMENT
1. Turn off all switches and unplug machine.
2. Remove recovery tank.
WARNING: The green
ground wire must be
attached for safe operation.
See wiring diagram.
Carbon
Brushes
3. Remove the (2) screws that fasten the solution tank to
the frame, and tilt tank back to expose the inside of the
frame.
If armature commutator is grooved, extremely pitted or not
concentric, the motor will need to be replaced or sent to a
qualified service center.
4. Locate the vacuum motor wires and disconnect at the
connector. Close the solution tank.
5. Remove the (6) screws holding the vacuum motor cover
(p/n 27809) to the solution tank.
6. Remove the vacuum motor.
Important:
7. Reverse process to install vacuum motor.
These brushes wear quicker as the length shortens due to
increased heat. Spring inside brush housing will damage
motor if brushes are allowed to wear away completely.
3
[9.5mm]
8
Periodically check the length of the carbon brushes. Replace
both carbon brushes when either is less than 3/8" (9.5mm)
long.
4-3
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ONLY QUALIFIED
MAINTENANCE
PERSONNEL ARE
WARNING:
TO PERFORM THE FOLLOWING REPAIRS.
BELT REPLACEMENT
1. Turn off all switches and unplug machine.
2. Remove recovery tank and brush.
3. Remove the (2) screws that fasten the solution
tank to the frame, and tilt tank back to expose
the inside of the frame.
4. Loosen the (4) screws that hold the brush motor
in place and slide motor forward to release
tension in belt.
5. Remove the (2) screws that fasten the vacuum
shoe links (p/n 05016) to the brush housing.
6. Remove the (3) screws that fasten the side plate
(p/n 62759) to the brush housing to remove belt.
NOTE: All components associated with driving
the brush will come out with the side plate.
7. Reverse process to install belt.
86249420
PRV NO. 62759
86227350
PRV NO. 05016
86037910 CEXT7 03/23/07
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORM
THE FOLLOWING REPAIRS.
! WARNING:
SOLUTION PUMP REPLACEMENT
1. Turn off all switches and unplug the machine.
2. Remove recovery tank.
3. Remove the (2) screws that fasten the solution tank to the frame, and tilt tank back to expose the
inside of the frame.
4. Remove solution hoses from fittings in pump.
5. Remove the (2) screws that fasten the pump to the frame.
6. Reverse process to install pump.
PUMP REPLACEMENT KITS SHURFLO 86026410 - PRV NO. (65257)
Pump Head
Replacement
86251050
Diaphragm
86235110
PRV NO. 29207
Valve Asm
86258840
PRV NO. 84162
PRV NO. 65188
4-5
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
86268450
86268830
PRV NO. 88332
PRV NO. 88636
862688900
PRV NO. 88655
86268830
PRV NO. 88636
86004480
PRV NO. 41353
86037910 CEXT7 03/23/07
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CHART
PROBLEM
CAUSE
SOLUTION
Is the cord plugged in.
Circuit breaker tripped in building.
Faulty switch.
Plug in cord.
No Power, Nothing
Runs
Reset breaker.
Call for service.
Faulty power cord or pigtail.
Call for service.
Vacuum Motor Will Not Vacuum circuit breaker tripped.
Reset breaker.
Run
Faulty main vacuum switch.
Loose wiring.
Call for service.
Call for service.
Faulty vac motor.
Call for service.
Debris lodged in vac shoe.
Remove debris from vac shoe.
Vacuum Motor Runs
But
Dome gasket defective or missing.
Vacuum hose cracked or hose cuff loose.
Recovery tank full / float ball stuck in the
up position.
Replace as necessary.
Replace or repair as necessary.
Turn off vac motor. Drain and rinse
recovery tank.
Suction Is Poor
Poor Or No Water Flow Main pump switch off.
(Carpet Is Streaky)
Turn on.
Jets clogged or missing.
Clean using a vinegar /water solution or
replace.
Solution filter clogged.
Drain solution tank and clean solution
filter.
Faulty solenoid.
Brush switch off.
Call for service.
Turn on brush switch.
Reset circuit breaker.
Replace as necessary.
Call for service.
Brush Does Not Spin
Brush circuit breaker tripped.
Brush belt broken.
Faulty brush motor.
4-7
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
4-8
86037910 CEXT7 03/23/07
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
30
19
7
18
21
15
SEE SOLUTION TANK
A
B
12
17
11
10
23
3
31
6
28
5
22
26
9
1
2
25
27
8
16
14
29
4
13
20
24
86037910 CEXT7 03/23/07
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
FRAME ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
86272160
86003620
86004340
86001660
86004480
86239610
86026150
86005640
86005810
86198530
86249430
86006020
86250130
86250140
86006580
86273980
86276610
86010630
86010660
86010650
86006550
86256190
86005710
86259960
86066230
86134490
86253090
86002370
86222760
86274760
86006530
66052
34341
39528
41236
41353
41354
53640
57030
57245
99809
62761
64099
66282
66288
70085
70066
70697
87013
87025
87018
70074
73197
57105
89506
03107
99667
73943
20035
20041
70271
70057
1
1
1
2
1
1
1
2
3
2
1
1
6
2
2
2
1
2
2
2
2
1
3
2
1
PIN, ROLL 1/8” X 1.0”L
FRAME, CLP FAMILY
HOSE ASM, 1.5 BLK VAC X 15.5
HUBCAP, 5/8” SHAFT
HARNESS, MAIN, CDT
HINGE, TANK TO FRAME
MOTOR ASM, BRUSH CLP FAMILY
NUT, 10-32 HEX NYLOCK
NUT, 1/4-20 HEX NYLOCK SS
FOAM TAPE, 1/8 THK X 3/4 1SDA
PLATE, BRUSH MTR CLAMP
PULLEY, 1.4 OD, 6GR, MICRO-V
PLUG, HOLE, .375” BLK
PLUG, 9/16 OD BLK NYLON
SCR, 1/4-20 X 1/2 PPHMS SS
SCR, 10-32 X 3/4 PPHMS
SCR, 1/4-20 X 1.25 PPHMS SS
WASHER, 1/4 ID X 5/8 OD SS
WASHER, 1/4 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
SET SCR, 10-32 X 1/4 KCP
STRAIN RELIEF, 90 DEGREE
NUT, 1/4-20 HEX W/ STAR WASHER
WHEEL, 1-15/16 X 10” HOOSIER
AXLE, 5/8 X 17.06L
10” HEAT SHRINK, 3/4 ID UL/CSA
1
1
1
2
2
SEAL, FRAME/TANK
CLAMP, 7/16 DIA NYLON UL
CLAMP, 2.0” WORM GEAR
SCR, 1/4-20 X ½ HHCS PLTD
SCR, 1/4-20 X 1 PPHMS SS
86037910 CEXT7 03/23/07
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH ASSEMBLY
31
15
25
11
7
8
25
29
16
12
30
26
24
18
38
16
39
10
22
30
34
4
5
2
40
37
36
33
41
26
43
32
35
17
28
9
3
21
13
27
6
42
1
19
14
23
17
20
25
30
29
86037910 CEXT7 03/23/07
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH ASSEMBLY
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
86000730
86228890
86000900
86001100
86227150
86001300
86001310
86003620
86001140
86004470
86004980
86093080
86126540
86264660
86005130
86005640
86005640
86249410
86249420
86264700
86114410
86006220
86006430
86006510
86006590
86006650
86006700
86275530
86010640
86010650
86007030
86230620
86251710
86003070
86003370
86281330
86272770
86272510
86008650
86008160
86006030
86003390
86004750
03110
09137
09019
11045
05158
140343
140351
34341
12514
41345
50998
51311
51312
51314
51317
57030
57271
62758
62759
62762
64098
66192
67411
70043
70088
70177
70232
70497
87016
87018
70675
12524
67467
27805
29157
70737
67094
66310
80604
73966
64102
29208
47416
1
2
1
1
1
1
1
AXLE, ROLLER
BEARING, R6 3/8 ID
BEARING, 1.125ODX.500IDX.375
BELT, 180J6 MICRO-V
ADAPTER, BRUSH BRG. DIE CAST
BRKT, BRUSH PULLEY
BRKT, BRUSH HEIGHT
REF FRAME, CLP FAMILY
9
1
1
1
1
1
2
1
4
2
1
1
2
1
1
1
2
6
7
2
2
4
6
4
1
1
1
1
1
1
2
2
1
1
1
BRUSH ASM, 15 IN
HOUSING, BRUSH 15"
LABEL, BRUSH HEIGHT
LINKAGE, ASM, BRUSH HEIGHT
LINKAGE ASM, ROLLER SUPPORT
LINK, ROLLER, FRONT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
LEVER, HEIGHT ADJUSTMENT
NUT, 10-32 HEX NYLOCK
NUT, 3/8 DIA CAP, TYPE PUSH PLT
PLATE, BRUSH HOUSING RH
PLATE, BRUSH HOUSING LH
PLATE, AXLE RETAINER
PULLEY, 2.2 OD, 6GR, MICRO-V
PIN, ROLL 1/4 X 1.25L
ROLLER, 1.9 DIA X 10.5 LG
SCR, 10-32 X 5/8 PFHMS
SCR, 10-32 X 1/2 PPHMS SS DL
SCR, 10-32 X 1/2 FHMS SS
SCR, 10-32 X 3/8 FHMS SS
SCR, #10-24 X 1/2 SHCS
WASHER, #10 LOCK EXT STAR SS
WASHER, #10 X 9/16 OD
SCR, 1/4-20 X.5/8 THMS PLTD NP
BRUSH, 15 L X 3.35 OD G2
RING, TOLERANCE 7/8
CLIP, BEARING
DRIVER, BRUSH
SHLDR BOLT, 3/8 OD X 3/8 L SS NP
RING, 1/2 EXT. SNAP
PIN, CLEVIS 1/4 X 1/2 PLTD
COTTER, 1/4" RING
SPACER, .81ID X 1.06OD, ALUM
PULLEY ASM, BRUSH
DRIVER ASM, BRUSH
REF KIT, BRNG/ADPTR EXTRCTR
86037910 CEXT7 03/23/07
5-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP ASSEMBLY
PRIOR TO SERIAL NO: 1000166663
14
3
20
13
4
10
16
9
2
8
16
21
23
18 1
12
19
15
20
17
11
7
25
26
28
6
C
5
(SEE SOLUTION
TANK)
26
24
27
86037910 CEXT7 03/23/07
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP ASSEMBLY
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
86002470
86002480
86003470
86003480
86004570
86004580
86005640
86026380
86250140
86006830
86273750
86003640
86008370
86026940
86010810
86010650
86010820
86005590
86005580
86003500
86274290
86004400
86267400
86281890
86004350
86281900
86253020
22072
22090
31072
31073
44067
44068
57030
65200
66288
70386
70011
34355
78420
84160
87191
87018
87192
56014
56012
31076
70162
39591
880278
39529
39530
39531
73963
1
2
1
1
2
2
2
1
2
2
2
1
1
1
2
4
2
1
1
2
2
1
1
1
1
3
1
COUPLING, 1/4 ANCHOR W/1" HEX
CONNECTOR, 1/8FPT X 1/4 TUBEQC
ELBOW, SWIVEL, 1/4MPTX1/4TUBE
ELBOW, SWIVEL,1/4MPTX3/8TUBEQC
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9504
NUT, 10-32 HEX NYLOCK
PUMP ASM, 115V 73 PSI W/CONN
PLUG, 9/16 OD BLK NYLON
SCR, 10-32 X 1.0 PPHMS
SCR, 1/4-20 X 5/8 HHCS SS
FITTING,1/4 TUBE,"Y", QC
TEE, 1/4 MPT X 3/8 TUBE, QC
VALVE ASM,SOLENOID CLP FAMILY
WASHER, 1/4"IDX1.0OD. FLAT SS
WASHER, #10 X 9/16 OD
WASHER, 7/16 X 3/4 X .19RUBBER
NIPPLE, 1/4 CLOSE
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NIPPLE, 1/4 FPT QD
ELBOW, 1/4 MPT X 3/8 TUBE, QC
SCR, 10-32 X 3/8 PPHMS SS
HOSE, 3/8 ID NYL11 YLW X 29”
WIRE, 22" GRN/18 76011 X 76011
HOSE, 3/8 URETHANE X 29"
HOSE, 3/8 NYLON X 6"
HOSE, 1/4 URETHANE X 6"
SCREEN, INTAKE
86037910 CEXT7 03/23/07
5-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP ASSEMBLY
FROM SERIAL NO: 1000166663
14
3
8
20
4
13
10
16
9
2
16
21
23
18
1
12
19
15
11
20
17
7
29
26
28
29
28
6
C
5
(SEE SOLUTION
TANK)
26
24
27
86037910 CEXT7 03/23/07
5-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PUMP ASSEMBLY
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
NOTES:
1
2
3
4
5
6
7
8
86002470
86002480
86003470
86003490
86004570
86004580
86005640
86026410
86250140
86274410
86273750
86003640
86008360
86258900
86010810
86010650
86010820
86247750
86234560
86003500
86006590
22072
22090
31072
31074
44067
44068
57030
65257
66288
70195
70011
34355
78419
84179
87191
87018
87192
56055
22097
31076
70088
OPEN
880278
39720
OPEN
39531
73963
39721
29277
1
2
1
1
2
2
2
1
2
2
2
1
1
1
2
4
2
1
1
2
2
-
COUPLING, 1/4 ANCHOR W/1" HEX
CONNECTOR, 1/8FPT X 1/4 TUBEQC
ELBOW, SWIVEL, 1/4MPTX1/4TUBE
ELBOW, SWIVEL, 3/8MPTX3/8TUBEQC
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9504
NUT, 10-32 HEX NYLOCK
PUMP ASM, 120V SHURFLO
PLUG, 9/16 OD BLK NYLON
SCR, 10-32 X 1.25 PPHMS SS
SCR, 1/4-20 X 5/8 HHCS SS
FITTING,1/4 TUBE,"Y", QC
TEE, 3/8 MPT X 3/8 TUBE, QC
VALVE ASM, 120V CLP FAMILY
WASHER, 1/4"IDX1.0OD. FLAT SS
WASHER, #10 X 9/16 OD
WASHER, 7/16 X 3/4 X .19RUBBER
NIPPLE, 1/4 BSPT X 1/4 NPT HEX
COUPLER, 1/4 FPT X MINI QC
ELBOW, 1/4 MPT X 3/8 TUBE, QC
SCR, 10-32 X 1/2 PPHMS SS
-
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
86267400
86282340
1
1
-
3
1
2
2
WIRE, 22" GRN/18 76011 X 76011
HOSE, 3/8 OD X 1/4 ID URTHN X 22"
-
HOSE, 1/4 ID NYLON X 5"
SCREEN, INTAKE
86281900
86253020
86282350
86279930
HOSE, 3/8 ID NYLON YLW X 17”
DUCT, 1/2 ID SPLT FLX X 16”
86037910 CEXT7 03/23/07
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM SHOE ASSEMBLY
1
4
11
7
10
9
2
3
12
5
8
6
86037910 CEXT7 03/23/07
5-9
Download from Www.Somanuals.com. All Manuals Search And Download.
VACUUM SHOE ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
86227350
86234760
86005810
86006790
86275120
86006840
86008130
86010620
86008120
86010630
86010700
86003780
05016
27674
57245
70351
70360
70390
73958
85039
73955
87013
87074
35171
4
1
4
2
4
4
8
1
2
4
8
1
ARM, VAC SHOE PARALLEL
COVER, ACCESSORY PORT
NUT, 1/4-20 HEX NYLOCK SS
SCR, 10-32 X 3/8 HHTR W/STAR
SCR, 1/4-20 X.75 PPHMS PHIL
SCR, 1/4-20 X 1 FHCS PLTD
SPACER, 3/8ODX.058WX.2814,CRS
VAC SHOE, 15"
SPRING, EXT .38D X2.75L X.055W
WASHER, 1/4 ID X 5/8 OD SS
WASHER, WAVE 3/8ID X3/4D X.125
GASKET, ACCESSORY PORT
10
11
12
86037910 CEXT7 03/23/07
5-10
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL ASSEMBLY
12
22
16
8
2
11
21
4
7
1
4
17
18
3
6
14
23
9
10
19
13
15
5
20
D
SEE SOLUTION TANK
86037910 CEXT7 03/23/07
5-11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PART NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
86001240
86001980
86230210
86002010
86234320
86005670
86005760
86064400
86006950
86006710
86007120
86007140
86256240
86010800
86004480
86242720
86010750
86005700
86006830
86234110
86242400
86242410
86245040
14020
14700
14832
14942
23679
57040
57116
61348
70532
70235
72126
72130
73505
87189
41353
500180
87100
57104
70386
23086
500077
500078
50279
1
1
1
2
1
2
2
1
9
2
1
2
1
9
TERMINAL BLOCK, 115V (3-4-3)
BREAKER, 15A 250VAC 50VDC
BREAKER, 6A VDE CIRCUIT
BOOT, 3/8 CIRCUIT BREAKER
CORD ASM, 14/3 X 22" YLW
NUT, 1/2 NPT CONDUIT
NUT, 6-32 W/STAR WASHER PLTD
PANEL, CADET CONTROL
SCR, 10-32 X 1/2 PPHMS BLK NP
SCR, 6-32 X 1.0 PH BLK NYLON
SWITCH, DPDT 3-POSITION ROCKER
SWITCH, SPST 2-POSITION ROCKER
STRAIN RELIEF, 1/2 NPT TRUMPET
WASHER, .2IDX.500 BLK SS
REF HARNESS, MAIN
1
2
3
1
1
1
1
1
LABEL, CONTROL PANEL
WASHER, 3/8 ID INT.LOCK THIN
NUT, 10-32 W/STAR WASHER PLTD
SCR, 10-32 X 1.0 PPHMS
CORD SET,14/3 SJTW-A X 50' YLW
LABEL, CIRCUIT BREAKER BRUSH
LABEL, CIRCUIT BREAKER VAC
LABEL, GROUND SYMBOL
86037910 CEXT7 03/23/07
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK ASSEMBLY
6
3
7
29
18
30
24
25
16
13
10
23
SEE CONTROL
PANEL ASM
D
17
7
15
12
18
A
SEE FRAME
ASM
21
22
32*
11*
8
9
28
19*
2
20
27*
1
5*
SEE PUMP
ASM
C
26*
4
B
SEE FRAME
ASM
18
14
86037910 CEXT7 03/23/07
5-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SOLUTION TANK ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
86233140
86233150
86003080
86003090
86235550
86003790
86003920
86281880
86240090
86004340
86001590
86240980
86026880
20041
20042
27809
27810
31081
35175
35231
39526
39527
39528
40049
41348
53789
3
1
1
1
1
2
2
1
1
CLAMP, 2.0" WORM GEAR
CLAMP, 3/8 HOSE (D-SLOT)
COVER, VAC MOTOR
COVER, BELT
ELBOW, 3/8 MPT X 3/8 TUBE, PLASTIC
GASKET, TANK TO VAC COVER
GASKET, VAC COVER
HOSE,1/2 CLEAR X 12
HOSE, 1.5 BLK VAC X 3.0
REF HOSE ASM, 1.5 BLK VAC X 15.5
1
1
1
HOSEBARB, 3/8MPT X 1/2 NYLON
HOUSING, VAC MOTOR
VAC MOTOR ASM
SERVICE
ONLY
-
86135320
140687
-
BRUSH SET, 120V VAC
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
86006600
86006590
86032240
86259060
86010650
86007970
86010630
86006580
86002370
86233260
86272840
86256170
86003950
86003960
86003970
86275690
86003940
86026660
70114
70088
75257
85037
87018
73864
87013
70085
20035
20092
67147
73169
35236
35237
35238
70525
35235
75276
2
2
1
1
10
1
3
3
2
1
1
1
1
1
1
6
1
1
1
SCR, #10 X 3/4 PPHST TYPE B
SCR, 10-32 X 1/2 PPHMS SS
TANK, CDT SOLUTION
VENT, COOLING AIR SMALL
WASHER, #10 X 9/16 OD
STRAINER, 3/8 IN. NPT 60 MESH
WASHER, 1/4 ID X 5/8 OD SS
SCR, 1/4-20 X 1/2 PPHMS SS DL
CLAMP, 7/16 DIA NYLON UL
CLAMP, 3.5" WORM GEAR
RING, 2" DIA SPLIT
STRAIN RELIEF, CORD HOOK
GASKET, TANK, L-F
GASKET, TANK, L-R
GASKET, TANK, RH
SCR, #10 X 1.0 PPHST TYPE B
GASKET, CDT PANEL
TANK ASM, SOLUTION
CLAMP, CABLE 1/2 ID 1/4BLT
*ITEMS
86177090 03-000261
86037910 CEXT7 03/23/07
5-14
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK ASSEMBLY
16
15
5
E
18
7
11
4
12
8
10
E
1
14
9
12
13
17
2
6
86037910 CEXT7 03/23/07
5-15
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOVERY TANK ASSEMBLY
SERIAL NO.
NOTES:
FROM
REF PART NO. PRV NO. QTY DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
86002400
86233140
86002930
86003110
86235280
86003630
86003910
86003930
86004200
86004510
86004500
86006600
86032250
86001370
86002870
86242230
86244670
86003300
20064
20041
27670
27816
28060
34351
35230
35232
39353
41391
41390
70114
75258
140408
27417
500009
501200
28061
1
1
1
2
1
1
1
2
1
1
1
6
1
1
1
1
1
1
CLAMP, 2.0" WORM GEAR X .312
CLAMP, 2.0" WORM GEAR
CORD, DRAIN HOSE
COVER, REC. TANK
DOME
FLOAT SHUT-OFF
GASKET, DOME
GASKET, PORT COVER
HOSE, 1.5 X 12.0 DRAIN
HOSE, INSERT
HOSE, CAP
SCR, #10 X 3/4 PPHST TYPE B
TANK, RECOVERY
BRKT, HOSE HOOK
CORD, 99807 1/8 X 12"
LABEL, WARNING
LABEL, MAIN
DOME ASM
86037910 CEXT7 03/23/07
5-16
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
SERIAL #
FROM
PART NO.
PRV NO. DESCRIPTION
NOTES:
86001140
86001100
86000900
86004570
86004580
86026410
86258900
86003780
86001980
86230210
86007140
86007120
86026880
86007970
86003630
86003330
86006240
86135320
12514
11045
09019
44067
44068
65257
84179
35171
14700
14832
72130
72126
53789
73864
34351
28061
66227
140687
BRUSH, ASM 15 IN
BELT, 180J6 MICRO-V
BEARING, 1.125ODX.500IDX.375
JET BODY, MINI PROMAX BODY
JET, MINI PROMAX 9504
PUMP ASM, 120V SHURFLO
VALVE ASM SOLENOID
GASKET, ACCESSORY PORT
BREAKER, 15A 250VAC 50 VDC
BREAKER, 6A VDE CIRCUIT
SWITCH, SPST 2-POSITION ROCKER
SWITCH, DPDT 3-POSITION ROCKER
VAC MOTOR ASM, CLP FAMILY
STRAINER, 3/8 IN. NPT 60 MESH
FLOAT, SHUT-OFF
1000166663
1000166663
DOME ASM
PLUG, DRAIN HOSE
BRUSH SET, 120V VAC
86037910 CEXT7 03/23/07
5-17
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The foregoing constitutes Century 400’s entire warranty and no other warranty, liability,
contingency or responsibility, direct, indirect, consequential or in any way connected with the
sale or operation of Century 400 machines or chemical products, either as expressed or
implied, will be honored.
CONDITIONS OF WARRANTY
This warranty shall not extend to any Century 400 product showing effects of misuse, abuse,
disassembly, alteration, lack of proper maintenance, corrosive chemicals, improper voltage,
accident damage, unauthorized repairs, use of other than genuine Century 400 parts and
material, fire, flood, freezing, normal wear or other cause beyond Century 400’s control.
LIMITED LIFETIME HOUSING WARRANTY
We, Century 400, hereby warranty our polyethylene machine housing for life to the original
distributor against cracking, leaking or deterioration. The limited lifetime warranty is offered to
the original owner only. Any transfer in ownership will void warranty. Additional terms and
conditions of the limited lifetime warranty on the housing are as follows: Ninja, Sensei, Spot
Plus, Hurricane and Turbomist will receive a full lifetime 100% replacement warranty. The RT-
Tanks will receive a (1) year 100% replacement warranty; all other polyethylene housings will
receive a full (5) year 100% replacement warranty, followed by 50% replacement value for life.
WARRANTY ON CHEMICAL USE
Improper use of chemicals voids warranty and Century 400’s liability. Defoamer is to be used in
all Century 400 machines. Dry cleaning solvents cannot be used in any Century 400 machine. If
used, fire and/or pump damage could result. White vinegar should be pumped through the
machine (1) time a week to prevent mineral scaling.
PARTS WARRANTY
Parts for Century 400 equipment shall have a (1) year replacement warranty from the date of
purchase for conditions considered normal wear, excluding any and all freight charges.
90 DAY UNLIMITED WARRANTY
Any equipment showing defect of any type within the first 90 days from date of purchase will
have an unlimited warranty which includes parts, freight, and 100% of labor costs. No labor or
freight will be covered after 90 days from the date of purchase.
LIMITED 90 DAY WARRANTY
The following parts, considered expendable under normal use, will be covered by warranty for
90 days from the date of purchase: quick disconnects, o-rings, seals, diaphragms, gaskets,
grommets, thermostats, brass fittings, hoses, etc. This warranty will include parts only.
USE OF PARTS NOT APPROVED BY CENTURY 400 WILL VOID ALL
WARRANTIES.
NOTICE: Failure to complete and return the warranty card within (10) days of receipt
of machine by purchaser will void all warranties.
Century 400, Inc., 325 S. Price Road, Chandler, AZ 85224 USA
Phone: (800) 752-1777 Fax: (480) 786-5724
z 2000 Century 400, Inc. All rights reserved. REVISED-A 02/01/01
Download from Www.Somanuals.com. All Manuals Search And Download.
|