GQ-100/200-1
GQ -100/ 200
BEFORE USING THE UNIT FOR THE FIRST TIME…
USING THE ALARM
1. Use a phillips head screwdriver to open the
battery compartment cover on the back of the
unit.
The alarm of this clock features a Snooze Function, which lets you catch a few
more minutes sleep in the morning. For full details on how to use this function,
see “To use the alarm”.
2. Remove the insulating paper from between the
batteries and contacts.
To set the alarm
3. Replace the battery compartment cover.
Each press of the + button increases the time by
one minute, and pressing – decreases it by one
minute.
• Holding down either button changes the time
setting at high speed.
[Control buttons]
GQ-100: on the front
–
+
GENERAL GUIDE
• The hour setting is changed automatically
whenever a change in the minutes increases
past 59 minutes or decreases past 00 minutes.
• The time display uses a 12-hour format, so
evening is indicated by “PM”.
• The configuration of your clock may differ somewhat from that shown in the
illustration.
• Hold down the Snooze/Light button to illuminate the display. The display
remains illuminated for a few seconds after you release the button.
GQ-200: on the bottom
+
–
GQ-100
GQ-200
ALARM SET
TIME SET
+
-
Snooze/Light button
Current time
GQ-200
GQ-100
Current time
-
TIME SET
+
Alarm time
Control buttons
Alarm On/Off switch
[Back]
[Back]
Alarm time
All reset button
To switch the alarm on and off
ALARM
ON
Slide the Alarm On/Off switch to the ON position to switch the alarm on, or to
the OFF position to switch it off.
RESET
RESET
OFF
• When you switch the alarm on, the alarm on indicator “
display.
” appears on the
Battery
ALARM SET
+
-
TIME SET
compartment
cover
Alarm on/off switch
(GQ-100: on the back
GQ-200: on the side)
[Bottom]
Control buttons
ALARM
ON
RESET
SETTING THE TIME
OFF
[Control buttons]
1. Hold down TIME-SET until the time starts to
flash on the display.
2. Each press of the + button increases the time by
one minute, and pressing – decreases it by one
minute.
GQ-100: on the front
TIME-SET
–
+
GQ-100
GQ-200
ON
ON
• Holding down either button changes the time
setting at high speed.
GQ-200: on the bottom
TIME-SET
OFF
OFF
• The hour setting is changed automatically
whenever a change in the minutes increases
past 59 minutes or decreases past 00 minutes.
• The seconds are reset to “00” whenever you
change the minutes setting.
On
Off
+
–
ALARM SET
TIME SET
To use the alarm
1. Set the alarm time and switch the alarm on.
2. When the alarm time you set is reached, the alarm starts to sound. It
continues for about one minute or until you stop it by pressing the Snooze/
Light button.
+
-
• The time display uses a 12-hour format, so
evening is indicated by “PM”.
GQ-200
Current time
GQ-100
Snooze/Light button
GQ-100
GQ-200
Alarm time
• When the alarm starts to sound, the alarm on indicator “
” flashes on the
display. This indicates that the Snooze function is activated.
3. About four minutes after you press the Snooze/Light button, the alarm starts
to sound again.
4. The above repeats up to seven times, or until you switch the alarm off (by
sliding the Alarm On/Off switch to the OFF position).
• You can stop the repeating alarm at any time by sliding the Alarm On/Off
Switch to the OFF position.
3. After you finish setting the time press TIME-SET to return to the Normal
Display.
• If you do not operate any button for a few minutes while the time is flashing,
the flashing stops and the clock goes back to the Normal Display automati-
cally.
• The beep pattern of the alarm changes (becomes faster) as the alarm
sounds. The pattern changes up to five times.
Download from Www.Somanuals.com. All Manuals Search And Download.
|