Impressa E Series
Fully Automatic
Coffee & Espresso Center
with Clearyl Water Care System
Operating Instructions
and Warranty
Customer Service 1-800-220-5701
Download from Www.Somanuals.com. All Manuals Search And Download.
D. This appliance has a polarized plug (one blade is wider
than the other). As a safety feature, this plug will fit in a
polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Do not attempt to defeat this safety
feature.
JURA-CAPRESSO
Jura was founded in 1931 in Switzerland.
Capresso was founded in 1994 in the USA.
Both companies have joined forces in the US to
bring you the finest Fully Automatic Coffee
Centers available anywhere. With innovative and
user-friendly features, high quality materials,
clear instructions and superb customer service,
we are sure you will experience the best coffee,
espresso, cappuccino or latte you have ever
had. We hope you will enjoy your new Fully
Automatic Coffee Center and will recommend it
to your friends. For more information about our
CAUTION
This appliance is for household use. Any servicing other than
cleaning and user maintenance should be performed by an
authorized service representative.
• Do not immerse base in water or try to disassemble.
• To reduce the risk of fire or electric shock, do not remove
the base. No user serviceable parts inside. Repair should
be done by authorized service personnel only.
• Check voltage to be sure that the voltage indicated on the
name plate agrees with your voltage.
• Never use warm or hot water to fill the water container!
Use cold water only!
Michael Kramm, President
• Keep your hands and the cord away from hot parts of the
appliance during operation.
• Never clean with scouring powders or hard implements.
3.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig.2
19 .Use dfCeeofCon tainer
20 .Tray
13 5 Grid
14 .Drawer
4.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
f. Rinse
a. On/Off
b. 1-Cup
mild
normal
strong
Fig. 6
g. Steam
d. 2-Cup
h. Pre-Ground
Coffee
e. Dial
e. Programming
Fig. 7
Fig. 13
Fig. 14
Frothing:
down
Steaming:
up
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19
Fig. 20
Fig. 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fa7.igM.e2t2al Tube b.. Chrome Sleevec.Steam Nozzle
Table of Contents
Page
Page
Important Safeguards / Jura-Capresso...............................2
Illustrations.......................................................................4–7
1. Product Registration......................................................9
2. Operating Instructions / Customer Service...................9
3. WELCOME TO THE IMPRESSA E SERIES ...............9
a. "Crema Coffee" and Pressure Brewing ...................9
b. Different Coffee Drinks...........................................10
c. Coffee Facts...........................................................10
4. Please Don't / Please Do ............................................10
5. Factory Settings ..........................................................11
6. PREPARING MACHINE FOR THE FIRST TIME........11
7. Adding Coffee Beans ..................................................11
8. Adjusting the Grinder ..................................................12
9. DAILY PREPARATION................................................12
10. Grinding and Brewing..................................................12
a. Selecting Cup Size and Strength...........................12
11. Using Pre-Ground Coffee............................................13
12. Using Hot Water..........................................................13
13. FROTHING AND STEAMING.....................................14
14. Heating and Frothing Milk...........................................14
15. Cleaning the Dual Frother Plus ...................................15
16. CLEARYL WATER CARTRIDGE................................15
a. Installing and Activating the Clearyl Cartridge ......15
b. Replacing the Clearyl Cartridge.............................16
17. Adjusting the Water Hardness.....................................17
18. PROGRAMMING........................................................17
a. AROMA ..................................................................18
b. Auto Shut-Off.........................................................18
c. Stats (Usage)..........................................................18
d. Language Selection ...............................................18
e. ML / OZ..................................................................18
f. Rinse ......................................................................19
19. CARE AND MAINTENANCE......................................19
a. Fill Water ................................................................19
b. Empty Tray / Empty Grounds.................................19
c
Fill Beans................................................................19
d. Stones and Beans..................................................19
e. General Cleaning Instructions................................20
f. Emptying System Before Transport.......................20
20. AUTOMATIC CLEANING CYCLES............................20
a. Rinsing ...................................................................20
b. Cleaning with Special Tablet..................................20
c. Decalcifying Procedure..........................................21
21. Tips for Better Coffee..................................................22
22. SUPPLIES...................................................................22
23. frothXpress Plus System (sold separately)..................22
24. Troubleshooting...........................................................23
25. WARRANTY.................................................Back Cover
Address Information / Customer Service...........Back Cover
8.
Download from Www.Somanuals.com. All Manuals Search And Download.
1. PRODUCT REGISTRATION
sure brewed coffee. Just press one of the two cup buttons and
your Impressa E will grind, tamp and brew your personal cup of
coffee. The integrated solid steel conical burr grinder grinds
beans to the preferred fineness. A separate funnel lets you use
pre-ground coffee. All coffee, water and steam functions are pro-
grammable to your own personal taste. Make any size cup of
coffee between 1 and 16 oz. The Dual Frother Plus* lets you
froth and steam milk for delicious cappuccinos and lattes. The
frother will deliver unlimited amounts of steam. The stainless
steel lined ThermoBlock prevents water from coming in contact
with aluminum and allows you to brew coffee immediately after
frothing (no purging). The hot water function lets you prepare tea
and other beverages in seconds. All important functions such as
water level, bean container, used coffee container and water
filter are monitored automatically. You can change the language
and can check how many cups of coffee you made.
Enjoy your Impressa E!
Please read the enclosed product registration form now. Fill it
out and mail or fax it to us within two weeks after purchasing
your machine or register online through our website:
warranty (chapter 24).
2. OPERATING INSTRUCTIONS / CUSTOMER SERVICE
Thank you for choosing this Jura-Capresso product.
• Please study these Operating Instructions carefully before
using your new machine. We highly recommend viewing the
enclosed video.
• Also included is a Quick Reference Guide, keep it next to
your machine.
• For further information please call our TOLL FREE number:
1-800-220-5701, Mon-Fri 9AM – 9PM & Sat 9AM – 5PM
Eastern Standard Time. If you call at any other time please
leave a message with your telephone number and when we
can call you back. You can send us a FAX at: 201-767-9684
or EMAIL us at [email protected]
* The frothXpress Plus, an automatic frothing device, is separately avail-
able (chapter 23). For details for the frothXpress Plus accessory see
video
3. WELCOME TO THE IMPRESSA E Series
3a. "CREMA COFFEE" AND PRESSURE BREWING
This fully automatic coffee center is completely programmable
and extremely user friendly. Your Impressa E can prepare one or
two cups of crema coffee at a time. The two-step pressure
brewing system – well known in commercial applications – was
adapted and refined by Jura coffee specialists and is the trade-
mark of each Jura-Capresso coffee center. This Pre-Brew
Aroma-System ensures optimal coffee extraction and will finish
every cup with a rich layer of "crema" – proof for perfectly pres-
According to the majority of coffee experts, grinding, tamping
and brewing under high pressure is the ideal extracting process
for maximum flavor and aroma. Your Jura-Capresso automatic
coffee center will always produce espresso and coffee with a
thick, foamy layer called "crema." The crema traps the fine aro-
matics and the light gaseous flavors that register on the palate.
The high pressure and the short brewing time prevent the
9.
Download from Www.Somanuals.com. All Manuals Search And Download.
extraction of bitter oils and release less caffeine than any other
brewing method. You will always make the absolute freshest
and most aromatic cup of coffee. This is the reason why many
European restaurants and hotels serve fresh pressured brewed
coffee only. Experiment with your new machine and prepare
yourself the best and most enjoyable cup of coffee!
prepared. Typical US espresso roasts result in darker beans with
an oily outside. European espresso roasts are medium brown
with no or very little oils showing on the outside.
Please note: Dark, oily beans: see chapter 7.
4. PLEASE, DON’T... (or you void your warranty protection):
• Never pull out the drawer during the brewing process.
• Never fill instant coffee into the bean container or ground coffee
funnel; it can damage the brewing chamber.
• Never fill sugar coated coffee beans into the bean container.
• Never fill frozen beans into the bean container. If you store
beans in the freezer, let them thaw for 3 to 4 hours before
filling them into the bean container.
• Never fill anything other than coffee beans into the bean
container (no chocolate, rice, nuts, spices, etc.)
• Never fill anything but fresh, cold clean water into the water
container, except when decalcifying (chapter 20b).
3b. DIFFERENT COFFEE DRINKS
Here are some guidelines for the most popular coffee drinks:
• Ristretto: 1/2 to 1 oz. of coffee. Sweeten to taste
• Espresso: 1 to 2 oz. coffee. Sweeten to taste
• Double Shot: 3 to 4 oz. of coffee. Sweeten to taste
• Crema Coffee: 5 to 8 oz. of coffee
• Cappuccino: Espresso plus 3 to 4 oz. of hot frothed milk.
• Latte: Espresso plus 3-5 oz. steamed milk with little or no froth.
• Café Mocha: Make Espresso then add chocolate syrup to the
milk before frothing/steaming.
Experiment with the size of your milk based drinks. For stronger
coffee taste add more coffee, for more milk taste use more
frothed milk.
• Never use mineral or carbonated water. You can use tap
water, spring water, distilled water and reverse osmosis water.
• Never repair or open the machine yourself. All repairs should
be performed only by an authorized service center.
3c. COFFEE FACTS
• Caffeine is tasteless. A "strong" coffee or espresso is mostly
the result of the amount of coffee in relation to the amount of
water. The longer a bean is roasted, the less caffeine it has.
• Arabica and Robusta are two genetically different kinds of
beans. "Arabica" beans have more flavor and a little less caffeine
than "Robusta" beans which are mostly used in lower priced
coffees and instant coffees.
PLEASE, DO...
• Fill water tank with fresh, cold water only.
• Remove any foreign particles (small stones) from coffee beans.
• Let frozen beans thaw for 3 to 4 hours before pouring them
into the bean container.
• Espresso is not a bean, it's the way the coffee is roasted and
10.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Place a cup underneath the frother (Fig. 13) and turn the
Steam/Water Selector to the Steam /Water symbol Fig 4b).
SYSTEM FILLING. The machine will pump some water
through the frother and stop automatically. SHUT TAP. Turn
the Steam/Water Selector back to the cup symbol. HEATING.
PRESS RINSE. Place a cup underneath the Coffee Spout
(Fig. 1,1) and press the Rinse Button (Fig. 3f). The machine will
pump a bit of hot water through the coffee spouts and will
stop automatically. READY. You can only brew coffee when
the display shows READY.
• Open the bean container lid (Fig. 1, 9) and fill with beans
(Fig. 5) for details see chapter 7.
• Place an empty cup (at least 8 oz.) under the coffee spouts.
• Push the Dial (Fig. 3e). The Dial illuminates and the display
shows the cup size 4 OZ.
• Push and hold the 1-Cup button until the display reads STRONG.
The Impressa E starts grinding and will start brewing.
Initially, the grinding chamber may not fill properly with ground
coffee. The machine will start brewing, then interrupt and the
display will show FILL BEANS. Push the 1-Cup button again.
Discard this first cup of coffee. Your next cup will be perfect.
Please note: If coffee only comes out of one spout, move the
spout up and down a few times to clear the internal flow.
You are now ready to make coffee.
All Display Messages Are Shown in RED
5. FACTORY SETTINGS
Each machine leaves the factory with the following settings:
Filter ..................... NO
Hardness Level .... 2
Aroma ................... ROBUST
Auto Off ................ 2 hours after last use
Language ............. English
Cup Size ………….. OZ.
Rinse ……………… ✔
The Dial is set to 4 OZ. for coffee and for hot water and
for 60 SEC for steam.
6. PREPARING THE MACHINE FOR THE FIRST TIME
• Make sure all accessories, literature and any other items are
removed from the machine and the water tank.
• Make sure the machine sits on an even, flat surface and the
drawer, tray and used coffee container are inserted (Fig 2).
• Plug-in machine.
• Do NOT fill water tank now.
Important: Do not install the Clearyl Water Filter cartridge
now. It can block the machine.
• Turn the machine on by pressing the ON/OFF button (Fig. 3a).
The display shows FILL WATER.
• Remove water tank, fill with fresh, cold water and replace.
7. ADDING COFFEE BEANS
• Open the bean container lid (Fig. 1, 9), fill with beans (Fig. 5).
The container holds approx. 220 grams (8 oz.). Close the lid.
Frozen Beans: Thaw for 3 to 4 hours be 0 TD [0-TadndingtY
The display shows OPEN TAP
The following procedure is only necessary when setting up the
machine for the first time and after the procedure "Emptying
System Before Transport" (chapter 19f).
Sugar Coated Beans: DO NOT fill sugar coated beans into the
bean container. The sugars will stick to the burrs and clog the
flow of ground coffee. Have your local coffee store grind
the sugar coated beans and use as described in chapter 11.
Using Oily Beans: Beans with an oily surface tend to stick
together. This may prevent a continuous flow of beans from the
bean container into the burrs. As a result the grinder does not
grind enough coffee and you might get weak or no coffee at all.
Stir the beans in the bean container just before grinding.
Alternatively, you can also pour the beans in an open bowl and
let them sit for about 5 hours. The oils will evaporate (this will
not change the taste of your coffee). Then fill the beans into the
bean grinder. Now beans will feed into the burrs more easily.
• Push and hold On/Off button until the display turns on. If your
machine is cold the display shows HEATING. After approx. 2
minutes the display shows RINSE.
• Press the Rinse Button (Fig. 3,f). Hot water will warm up all
internal parts and pump through the coffee spouts. The water
will be caught in the drawer underneath. The rinse cycle stops
by itself and the display reads: READY You are now ready to
make coffee.
10. GRINDING AND BREWING
The Impressa E uses a 2-step brewing process (Pre-Brew Aroma
System). First it moistens the ground coffee (pre-brew phase),
pauses for a few seconds and then starts the brewing process.
• Adjust the height of the coffee spout to your cup size (Fig. 12)
and place one or two cups underneath the coffee spouts.
8. ADJUSTING THE GRINDER
You can adjust the grinder to the roast of your coffee.
We recommend the following:
Light roast: use a finer adjustment.
Dark roast: use a coarser adjustment.
• Open the lid of the bean container.
• While the grinder is running turn the grind selector switch to
the desired position (Fig. 6).
– The smaller the dots, the finer the grind.
– The bigger the dots, the coarser the grind.
Important: The grinding grade can only be adjusted while
the grinder is actually grinding.
10a. SELECTING CUP SIZE AND STRENGTH
Cup Size 1 OZ. to 8 OZ; max: 16 oz.
• Push the Dial. It will illuminate and the display will show the
cup size in oz, e.g. 4 OZ.
• Turn the dial to select any cup size between 1 OZ. and 8 OZ.
Your machine will always remember the last setting. After 5
seconds the display will change back to READY.
• When using the 2-Cup button the machine will automatically
double the selected amount of coffee.
Coffee Strength MILD – NORMAL - STRONG
Push the 1-Cup button once, the display shows MILD.
Push the 1-Cup button twice, the display shows NORMAL.
Push the 1-Cup button three times, the displays shows STRONG.
You can also push and hold the 1-Cup button until the desired
strength is shown in the display.
9. DAILY PREPARATION
ON/OFF Button – HEATING – RINSE – READY
We recommend filling the water container every morning with
fresh, cold water. This will enhance the taste of your coffee.
12.
Download from Www.Somanuals.com. All Manuals Search And Download.
Grinding times (approx.)
• Open the lid for the ground coffee funnel (Fig. 1.8) and fill the
funnel with one or two scoops of ground coffee.
Important: Do NOT fill this funnel with instant coffee and do
not use more than two level scoops of coffee.
MILD .......... 6 to 7 seconds.
NORMAL ... 7.5 to 8.5 seconds.
STRONG..... 9 to 10 seconds.
• Push the 1-Cup or 2-Cup button. The machine will tamp and
brew coffee.
AROMA-setting "STANDARD" has the shorter grinding times.
AROMA-setting "ROBUST" has the longer grinding times.
When using the 2-Cup button the grinder will always grind
between 9 and 10 seconds.
Please note: If you push the scoop button accidentally push
the 1-Cup button. Display shows ADD MORE POWDER. The
machine will start brewing, stop and return to READY.
Please note: After use of sugar coated or flavored coffee
through the pre-ground coffee funnel you may experience some
flavor transfer when going back to your regular coffee.
• Push and hold the Rinse Button (Fig. 3f) until the display
shows RINSE.
Please note:
When using the 1-Cup button, the display will first show the
strength setting. When the pre-brew cycle starts, it will show the
actual cup size. At this time you can still change the cup size by
turning the Dial.
When using the 2-Cup button, the display will first show
2 CUPS. When the pre-brew cycle starts, the display shows the
cup size for one cup. At this time you can still change the cup-
size by turning the Dial.
• The Dial illuminates. Push the Dial (Fig. 3e). The machine will
perform one rinse cycle and the display will return to READY.
12. USING HOT WATER
Please note: After the pre-brew cycle you can always stop the
brewing process by pushing the 1-Cup or 2-Cup button. This will
not affect your cup size setting for the next brew cycle.
Important: Never try to pull out the tray as long as the machine
is grinding, brewing or discarding the used coffee. Always wait
until the display shows READY.
READY – 1 OZ. to 16 OZ. – SHUT TAP - READY
The hot water feature allows you to make a cup of tea, a quick
soup or add hot water to your coffee, making it less strong.
• Place a cup underneath the frother (Fig. 13).
• Turn the Steam/Water Selector to the water symbol (Fig. 4b).
Hot water will push through the frother. The display shows the
amount of hot water. You can change it from 1 to 16 oz. by
turning the Dial (Fig. 3e) now. The machine remembers the last
setting. When the water flow stops, display shows SHUT TAP.
• Turn the Steam/Water Selector back to the cup symbol. READY.
Please note: You can always stop the flow of hot water by
turning the dial to the cup symbol.
11. USING PRE-GROUND COFFEE
You can also use pre-ground coffee, bypassing the grinder. This
comes in handy if someone requests decaf, sugar coated or
flavored coffee.
• Push the Pre-Ground Coffee Button (Fig. 3h). The display
shows: FILL POWDER
13.
Download from Www.Somanuals.com. All Manuals Search And Download.
13. FROTHING and STEAMING
The steam function can be used to heat up any liquid and to
steam and froth milk.
Steaming Position:
The Frother's metal cylinder is in the UP position (Fig. 16). In the
steaming position hot steam is injected into the milk (or any
other liquid) without creating a frothy layer on top.
Typically a Latte has steamed milk with no froth.
Please note: When you start steaming, some hot water will
push out of the nozzle before the steam begins. When frothing
a lot of milk this will not change the taste of your frothed milk.
You can also release this small amount of hot water into the
tray or into a separate container:
• Turn the Steam/Water Selector to the Water Symbol for one
second and then back to the Cup symbol. Now start
frothing/steaming.
Please note: When you stop the steam output the display will
show STEAM READY for the next 20 seconds. Within this
time you can continue to use the steam function.
If you want to steam at a later time you must first press the
Steam button (Fig. 3g).
Frothing Position:
The Frother's metal cylinder is in the DOWN position (Fig. 16). In
the frothing position hot steam and air is injected into the milk
creating warm milk and a firm layer of tiny froth bubbles.
14. HEATING AND FROTHING MILK
Tips for frothing (Cappuccino):
READY – HEATING - STEAM READY - 60 SEC - CLOSE TAP
• Push the Steam button (Fig. 3g). Display shows HEATING.
• Add cold milk to a pitcher or a cup.
The tip of the frother should not touch the bottom of your pitcher.
Start in the steaming position – cylinder "up" (Fig. 16) – for a few
seconds. Then push the cylinder "down". Milk froth will build up.
This way the froth on top of your milk is also warm. If the frothed
milk is not warm enough, continue in the steaming position.
Steaming and frothing directly in your cappuccino cup:
With practice, you can steam and froth directly in your
cappuccino cup. First steam and froth the milk, then add your
espresso shot.
• After 15 to 30 seconds the display shows STEAM READY.
• Immerse the tip of the frother into the milk (Fig 17&18) and
turn the Steam/Water Selector to the Water/Steam Symbol.
Hot steam will be injected into the milk. The display shows
how long steam will be forced through the frother, 60 SEC.
• At this time you can change the steam output from 3 and 120
seconds. The machine will remember your last setting. When
the selected steam time is up, the display shows SHUT TAP.
• Turn the Steam/Water Selector to the cup symbol. If you need
more steam turn the Selector back to the water/steam symbol.
Please note: You can always stop the steam output by turning
the Steam/Water Selector to the cup symbol.
Please note: The less fat content the milk has the more froth will
be created. Skim milk will produce the most froth and will let you
taste more of the coffee. 1% and 2% milk will give you less
froth. Regular whole milk (3% fat) will produce the least amount
of froth. You can also use soy milk.
14.
Download from Www.Somanuals.com. All Manuals Search And Download.
15. CLEANING THE DUAL FROTHER PLUS
Always keep the Dual Frother Plus clean and free of milk
deposits. Hardened milk particles will make it impossible to
create milk froth.
• Assemble the Dual Frother and make sure that the tip is
screwed onto the Connector finger tight (Fig 14a, c).
• Push the black Clip-on Connector (Fig.14c) firmly into the
steam nozzle (the connector should sit flush with the chrome
sleeve (Fig. 15b) so that the steam nozzle is no longer visible).
Please note: If the parts are not put together tightly it will not be
possible to create the frothy foam on top of the milk.
Fast cleaning:
Display shows READY. Place a cup underneath the frother (Fig.
13) and turn the Steam/Water Selector to the water symbol. Let
hot water run through the frother for about 3 seconds and then
stop. This will flush out any small milk droplets.
16. CLEARYL WATER FILTER CARTRIDGE
The machine comes with one Water Filter Cartridge. This
cartridge is specially made for use with the Impressa E series.
The cartridge:
• Reduces the water hardness up to 75%.
• Removes (if present) up to 85% chlorine, up to 90% lead, up
to 95% copper and up to 67% aluminum.
• Cleans the water through an upward current principle (Fig. 8)
just before the brewing cycle starts, ensuring freshly filtered
water every time you make coffee.
• Eliminates decalcifying. When using the water filter cartridge,
you never need to decalcify your machine.
Thorough cleaning of the Dual Frother parts:
• Remove the Dual Frother (Fig.14) from the Steam Nozzle
(Fig. 15c).
Please note: The Dual Frother is tightly connected to the
Steam Nozzle. First loosen the Clip-On Connector part (Fig. 14c)
by turning it a few times, then push down to remove.
• Unscrew the black tip (Fig.14a) from the Clip-On Connector
(Fig. 14c). You can use a coin to loosen the black tip.
• Soak all three parts in hot soapy water.
• Make sure that the two side holes and the channel of the black
tip (Fig. 14a) are free of any milk deposits.
• To reorder cartridges see chapter 22 "Supplies".
Cleaning the Steam Nozzle (Fig. 15c)
• Place a cup underneath the Steam Nozzle (the Dual Frother is
off) and let a bit of hot water run through the Steam Nozzle.
Tip: If the steam nozzle is blocked by hardened milk, use a
needle and loosen up the milk deposit. Then let some hot
water pass through the Steam Nozzle.
16a. INSTALLING & ACTIVATING THE CLEARYL WATER
CARTRIDGE
Important: Never install the cartridge before or during
"Preparing Machine For The First Time."
• Make sure the water tank is empty.
• Remove cartridge from its bag and rinse cartridge under water
• Open water container lid and pull up the holder for the
cartridge (Fig.9).
Assembly of Frother Parts
• Make sure the Steam Nozzle is screwed onto the Metal Tube
(Fig. 15a) finger tight.
15.
Download from Www.Somanuals.com. All Manuals Search And Download.
• Insert the cartridge with its tapered end down. Make sure it
fits snugly over the white mesh piece inside the water
container. Push down gently (Fig.10).
• Close the holder for the cartridge so that it engages in the
water tank (Fig.11).
• Fill the water tank with fresh cold water and replace.
You must activate the cartridge as follows:
1. Push and hold the P button (Fig. 3e). FILTER –
2. Push the Dial and the display shows NO –
3. Turn the Dial until the display shows YES ✔
4. Push Dial confirm. The display shows INSERT / OPEN TAP
5. Place a 20 oz. container underneath the frother.
6. Turn the Steam/Water Selector to the water symbol.
FILTER RINSING. For the next 90 seconds the machine will
push water through the filter and through the frother. Do not
interrupt this process. This activates the filter.
The machine will stop automatically.
use less than 75 liters of water. In this case, no message will
appear in the display.
Important: Once the filter has lost its calcium suppressing
abilities, calcium will build up inside the machine. Since the
Water Hardness Selector is off, the machine will not remind you
when to decalcify. This could clog and ruin your machine.
• Remove the old filter. The cartridge is environmentally friendly.
Dispose it with your regular household trash.
• Make sure the water tank is empty.
• Remove the new cartridge from its bag.
• Open water container lid and pull up the holder for the
cartridge (Fig. 9).
• Insert the cartridge with its tapered end down. Make sure it
fits snugly over the white mesh piece inside the water
container. Push down gently (Fig.10).
• Close the holder for the cartridge so that it engages in the
water tank (Fig.11).
• Fill the water tank with fresh cold water and replace.
1. Push and hold the Rinse Button. The display shows RINSE
and the Dial is illuminated.
2. Turn the Dial until the display shows FILTER.
3. Push the Dial. The display shows REPLACE OPEN TAP.
4. Place a 20 oz. container underneath the frother.
5. Turn the Steam/Water Selector to the water symbol.
FILTER RINSING
For the next 90 seconds the machine will push water through
the filter and through the frother. Do not interrupt this process.
This activates the filter. The machine will stop automatically.
6. SHUT TAP. Turn the Water/Steam Dial back to the cup symbol.
HEATING. READY.
7. SHUT TAP. Turn the Water/Steam Dial back to the cup symbol.
HEATING. READY.
Please note: As long as the filter is activated, the water
hardness setting is automatically turned off.
16b. REPLACING THE CLEARYL WATER CARTRIDGE
The filter is monitored automatically. After approx. 75 liters of
water (~2,500 oz.), the filter loses its effect. The display changes
from READY to CHANGE FILTER / MACHINE READY. You can
still make coffee, but we recommend replacing the filter within
one week!
Attention: The filter should be changed every 3 months if you
16.
Download from Www.Somanuals.com. All Manuals Search And Download.
17. ADJUSTING THE WATER HARDNESS
you when it is time to decalcify. Turning off the monitor requires
you to use distilled water only or the Water Filter Cartridge
(chapter 16a).
Water is heated inside the machine. With use, this leads to
calcium deposits forming inside the machine. The display will
remind you when it is time to perform a decalcifying cycle. The
machine is set to level 2 (medium hard water). If you have
harder water you need to set it to a higher level. If you have
softer water you can set it to level 1. If you are not sure about
the hardness of your water, ask your local water company for
the "Water Hardness in Grains."
HARDNESS LEVEL 1: grains 2-9
HARDNESS LEVEL 2: grains 10-19
HARDNESS LEVEL 3: grains 20-29
HARDNESS LEVEL 4: grains 30+
18. PROGRAMMING
Please note: As long as you are in programming mode, you
cannot brew coffee.
• Press and hold the P button until the display shows FILTER.
Turning the Dial clockwise the following functions will appear
in the display:
HARDNESS
AROMA
AUTO OFF
STATS
LANGUAGE
ML / OZ
You can also use the enclosed water hardness indicator strip to
determine the water hardness:
• Insert the stick for one second into the water you want to
use. Shake off any access water and wait for one minute.
• If all five fields of the test stick turn reddish, set the hardness
level to 4. If four fields turn reddish, set the hardness level to 3.
If three or less fields turn reddish, leave the level in position 2.
• If you use Spring Water you can set the hardness level to 1.
You can change the hardness settings as follows:
1.Push and hold the P button (Fig. 3e). FILTER –
2.Turn the Rotary Dial until the display shows HARDNESS.
3.Push the Dial. LEVEL 2
RINSE ✔
To change functions the procedure is always the same:
1. Push and hold P button until display shows FILTER.
2. Turn Dial to the function you want to change or look up.
3. Push Dial.
4. Turn Dial until desired selection is displayed.
5. Push Dial to confirm selection.
6. Push the P button to get back to READY.
FlLTER: See chapter 16a.
HARDNESS: See chapter 17.
4.Turn the Dial to select from 1 2 3 4 –
5.Push the Dial to confirm your selection. HARDNESS.
6.Push the P button. READY.
Important: If you choose the selection "–" the water hardness
monitor is turned off. In this case the machine will NOT remind
17.
Download from Www.Somanuals.com. All Manuals Search And Download.
18a. AROMA
works more effectively after the brewing chamber has cooled down.
1. Push and hold P button until display shows FILTER.
2. Turn Dial to AROMA
3. Push Dial: ROBUST
4. Turn Dial to select from STANDARD or ROBUST
5. Push Dial to confirm selection.
6. Push the P button to get back to READY.
In ROBUST the grinder will always grind approx. 1 second
longer to increase the strength of your coffee.
18c. STATS (usage)
1. Push and hold P button until display shows FILTER.
2. Turn Dial to STATS
3. Push Dial: The display shows the total number of cups brewed.
4. Push the 1-Cup, 2-Cup and the Ground Coffee Button to
display usage for those buttons.
5. Push the P button TWICE to get back to READY.
18d. LANGUAGE SELECTION
1. Push and hold P button until display shows FILTER.
2. Turn Dial to LANGUAGE
3. Push Dial: ENGLISH
4. Turn Dial to select from English, German, French, Italian
Spanish, Portuguese, Dutch (NL)
5. Push Dial to confirm selection.
6. Push the P button to get back to the "READY" mode.
18b. AUTO SHUT-OFF
1. Push and hold P button until display shows FILTER.
2. Turn Dial to AUTO OFF
3. Push Dial: 2.0 HRS
4. Turn Dial to select from -.- HRS to 9.0 HRS
5. Push Dial to confirm selection.
6. Push the P button to get back to READY.
In selection -.- HRS the machine will not shut off automatically.
Please note: When the machine turns off, it will automatically
run a hot water rinse cycle. The water will push through the
coffee spouts and will be caught in the tray.
Recommendation:
• If you use the machine in the morning and then later in the
day, set the auto-shut off between 0.5 HRS and 2.0 HRS.
• If you use the machine all day long set the auto shut off
between 3.0 HRS to 5.0 HRS.
18e. ML/OZ
Instead of showing the cup sizes in Ounces (OZ) you can display
it in Milliliters (ML). 30 ML equals 1 OZ.
1. Push and hold P button until display shows FILTER.
2. Turn Dial to ML / OZ
3. Push Dial: OZ.
4. Turn Dial to select ML or OZ.
5. Push Dial to confirm selection.
6. Push the P button to get back to READY.
• If you make only one or two cups of coffee in the morning, set
the machine to 0.5 HRS.
Important: Never turn the machine off immediately after you
have made a cup of coffee. The automatic hot water rinse cycle
18.
Download from Www.Somanuals.com. All Manuals Search And Download.
18f. RINSE
• Place the used coffee container on the tray and insert back
into the machine (Fig. 21). The display shows READY and you
may now continue brewing coffee.
You can turn off the automatic rinsing mode for when the
machine shuts down.
1. Push and hold P button until display shows FILTER.
2. Turn Dial to RINSE
3. Push Dial: RINSE ✔
4. Turn Dial to select RINSE –
5. Push Dial to confirm selection.
19c. FILL BEANS
When the display shows FILL BEANS, open the bean container
lid and add beans (Fig. 5).
Please note: The message FILL BEANS will disappear after
making the next cup of coffee.
Attention: If the display shows FILL BEANS and there are
ample beans in the bean container, stir the beans so they flow
into the grinder (chapter 7). We recommend cleaning the bean
container from time to time with a dry cloth before you refill
beans (please make sure the machine is turned off when cleaning).
6. Push the P button to get back to READY.
19. CARE AND MAINTENANCE
19a. FILL WATER
When the display shows FILL WATER, no more coffee can be
made until you fill the water container. The water container will
never be completely empty. The low water floatation device
(Fig. 7.4) activates the FILL WATER indicator when there are
about 10 oz. of water left.
19d. STONES AND BEANS
Every coffee specialty store will tell you that occasionally small
stones can be found in with coffee beans. Small stones will be
processed through the burr grinder without any harm (the stone
will end up in the used coffee container).
• Remove water tank, rinse and fill with fresh water and replace.
However larger stones can block the burr grinder. The noise of
the grinder will become very loud and the grinder will block. In
this case please call our Customer Service: 1-800-220-5701.
19b. EMPTY GROUNDS
Used coffee grounds are collected in the used coffee container
(Fig. 2.19). If the display shows EMPTY GROUNDS, no more
coffee can be made until you empty the used coffee container.
• Carefully lift and remove drawer since there is water in it (Fig. 19).
The display shows DRAWER MISSING.
Before Filling Beans into the Bean Container:
• Shake your bean bag thoroughly so that a stone will fall to the
bottom of the bag.
Important: Do not unplug the machine while you are emptying
the coffee grounds.
• Before emptying the bean bag completely, check if there are
any particles that look like stones and remove them.
• Empty the used coffee container and the drawer.
• Push the drawer back into the machine (Fig. 20). The display
still shows DRAWER MISSING.
19.
Download from Www.Somanuals.com. All Manuals Search And Download.
19e. GENERAL CLEANING INSTRUCTIONS
• Push the Dial. Hot water is dispersed through the coffee
Never use abrasive materials or chemicals to clean the machine.
spouts and will stop automatically. READY.
• Clean the housing with a soft, damp cloth.
• Rinse water tank daily and fill with fresh, cold water.
20b. CLEANING WITH SPECIAL TABLET
The machine monitors how many coffees are brewed and how
often the rinsing program is activated. After approx. 200 coffees
the display will show CLEAN MACHINE / MACHINE READY.
Please note: You can continue making coffee, however we
highly recommend that you clean the machine as described
below within the next few days. This cleaning program will
remove oil build-ups in the brewing chamber. The cleaning pro-
gram takes about 15 minutes. Please use one white cleaning
tablet (enclosed). The machine comes with a pack of 2 tablets.
To re-order cleaning tablets see chapter 22.
Important: Once the cleaning program has started do not
interrupt the procedure.
1.Make sure the machine is on and the water tank is full.
2.Push the Rinse button. The display shows EMPTY DRAWER.
3.Remove and empty the drawer and used coffee container and
replace complete assembly (Fig. 21).
Important: Even if the drawer and the used coffee container are
empty, you still need to remove the drawer for approx. 20 seconds
and then replace it. The display shows PRESS RINSE.
4.Place a 12 oz. container under the coffee spouts.
5.Push the Rinse button. The display shows CLEANING.
After a moment the display shows ADD TABLET/ PRESS RINSE.
6.Open the ground coffee lid and drop in one white cleaning
tablet (Fig. 22). Your machine comes with a pack of two
tablets. To order more tablets see chapter 22 "Supplies".
19f. EMPTYING SYSTEM BEFORE TRANSPORT
This procedure is necessary to prevent water and frost damage
in case you intend to transport your machine.
• Turn machine off.
• Place a cup underneath the frother.
• Push and hold the Steam Button until the display shows:
OPEN TAP. Turn the Steam/Water Selector to the water symbol.
The machine will push a bit of water and steam into the cup
underneath the frother.
• When display shows CLOSE TAP turn the Steam/Water Selector
back to the cup symbol. The machine will automatically shut off.
Important: The next time you turn the machine on you must
follow the instructions in chapter 6.
Please note: Before transporting the machine, make sure that
the water tank is empty, the filter cartridge is removed (discard
and use a new cartridge), the bean container is empty, the
drawer and used coffee container are empty and clean.
Secure the lids of the water tank and the bean container with
scotch tape. Pack entire machine with thick cushioning material
on all sides to prevent damage.
20. AUTOMATIC CLEANING CYCLES
20a. RINSING
You can run an extra hot water rinse cycle as follows.
• READY. Push and hold the Rinse button until display shows
RINSE. The Dial illuminates.
20.
Download from Www.Somanuals.com. All Manuals Search And Download.
7.Push the Rinse button. The display shows CLEANING.
The cleaning program will dispense hot foamy water in
intervals through the coffee spout into the drawer.
8.When finished, the display shows EMPTY DRAWER.
9.Lift and remove the drawer. Empty the used coffee container
and drawer and replace. The display shows READY indicating
the machine is now ready to brew coffee again.
Attention: You can run a tablet cleaning cycle at anytime even if
the machine does not prompt you,
This might damage internal parts of the machine.
1. Push the Rinse button. The display shows EMPTY DRAWER.
2. Remove and empty the drawer and used coffee container
and replace complete assembly (Fig. 21).
Important: Even if the drawer and the used coffee container
are empty, you still need to remove the tray for approx. 20
seconds and then replace it. The display shows SOLVENT IN
TANK.
3. Make sure the water tank is empty. Completely dissolve two
of the light brown tablets in 16 oz. of water and pour this
mixture into the water tank.
• READY. Push and hold the Rinse button until display shows
RINSE. The Dial illuminates.
• Turn the Dial until display shows CLEANING. Push the Dial.
Display shows EMPTY DRAWER.
4. Replace water tank. Place a large container (at least 20 oz.)
underneath the frother.
• Continue with step 3 above.
5. The displays shows SOLVENT IN TANK OPEN TAP. Turn the
Steam/Water Selector to the water symbol. The machine will
pump the mixture through the frother in intervals. During this
procedure the display shows DECAL ON. When this cycle is
finished the display shows SHUT TAP.
6. Turn the Steam/Water Selector back to the cup symbol.
The display shows DECAL ON. Now the machine pumps the
mixture through the coffee spout into the drawer.
7. When this cycle is completed the display shows EMPTY
DRAWER. Remove the container from underneath the
frother. Carefully lift and remove the drawer, empty and
thoroughly rinse all parts and replace. The display shows
FILL WATER.
20c. DECALCIFYING PROCEDURE
The machine has an integrated decalcifying program. When the
display shows DESCALE MACHINE / MACHINE READY it is
time to decalcify the machine. You can still make coffee.
However, it is highly recommended that you decalcify the machine
within the next 3 to 4 days.
Please note: If you use the Clearyl water cartridge and the
display shows DESCALE MACHINE / MACHINE READY, then
your cartridge function is not activated. Follow the instructions in
chapter 16a to program the Clearyl Cartridge function.
Important: The decalcifying program must not be interrupted.
8. Remove the water tank, rinse thoroughly, fill with cold fresh
DECALCIFYING AGENT: Only use our special decalcifying
tablets. For supplies see chapter 22.
water and replace.
CAUTION: Never use vinegar or any other decalcifying agent.
21.
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Place a large container (at least 20 oz.) underneath the
frother. The display shows OPEN TAP.
10. Turn the Steam/Water Selector to the water symbol.
The machine will pump hot water through the frother in
intervals. During this procedure the display shows DECAL ON.
When this cycle is finished the display shows SHUT TAP.
11. Turn the Steam/Water Selector back to the cup symbol.
Pre-warm cups
You should warm cups in advance with hot water or steam.
The smaller the quantity of coffee, the more important it is to
warm your cups.
Sugar and cream
Warmth is lost by stirring the contents of the cup. Adding milk or
cream from the refrigerator considerably lowers the temperature
The display shows DECAL ON. Now the machine pumps hot of the coffee. You can preheat milk and cream with the frother.
water through the coffee spout into the drawer.
12. When the cleaning cycle is completed the display shows
EMPTY DRAWER. Remove the container from underneath
the frother. Carefully lift and remove the drawer, empty and
thoroughly rinse all parts and replace. The display shows
PRESS RINSE.
22. SUPPLIES AND ACCESSORIES
The following supplies are necessary to keep your machine in
good working order:
• Clearyl Water Filter Cartridge - Model #64533
• Special Cleaning Tablets (white tablets) - Model #62205
• Decalcifying tablets (light brown tablets) - Model #61848
Please note: You must use decalcifying tablets if you do not use
the Clearyl cartridge.
13. Push the Rinse Button. The machine will run a regular rinse
cycle and the display will show READY.
14. Clean front of machine and grid with a moist, soft cloth.
Attention: You can run a decalcifying cycle at anytime even if
the machine does not prompt you,
• READY. Push and hold the Rinse button until display shows
RINSE. The Dial illuminates.
• frothXpress Plus System - Model #64342
All supplies are available through:
- the enclosed mail order form that came with your machine
- our toll free line at 1-800-220-5701 or
• Turn the Dial until display shows DECAL ON. Push the Dial.
Display shows EMPTY DRAWER.
• Continue with step 2 above.
23. FROTHXPRESS PLUS SYSTEM WITH MILK CONTAINER
If you prepare many Cappuccinos or Lattes at a time, we recom-
mend the fast and precise frothXpress Plus System. The system
replace the Dual Frother Plus and allows you to fill cup after cup
with the desired amount of hot milk and milk froth automatically.
See video for details. Sold separately.
21. TIPS FOR BETTER COFFEE
Height adjustable coffee-spout
Adjust the height of the coffee-spout to the size of your cups.
Grinding
Please refer to chapter 8 "Adjusting the Grinder."
22.
Download from Www.Somanuals.com. All Manuals Search And Download.
24. TROUBLESHOOTING
C. INSUFFICIENT FROTHED MILK PRODUCTION
Reason: Milk is initially not cold enough or your milk is not
suited for thick frothing.
Solution: Make sure milk is cold. Use a different type of milk.
Skim milk will produce the thickest and longest lasting froth. Full
fat milk will produce less thick froth. See chapter 14.
Reason: The components of the frother are not assembled
properly, or the components are clogged with hardened milk, or
one or more of the components is missing, or the steam nozzle
is clogged.
A. NO COFFEE COMES OUT OF THE COFFEE SPOUT
Reason: Beans in bean container are not feeding properly into
the grinder because they are stuck together.
Solution: Stir beans before grinding and while grinding turn the
grinding selector to the coarsest setting. See chapter 7.
Reason : You used ground coffee in the ground coffee funnel.
The ground coffee was too fine.
Solution: Use ground coffee which is ground somewhat coarser.
Reason : No water is transported through the system.
Solution: Remove water container and make sure that the con-
necting valve is free of any particles (like a coffee bean etc).
Reason: The ground coffee funnel or the internal brewing chamber
is clogged.
Solution: (See chapter 15)
a. Remove frother. Check that steam comes out of the steam
nozzle. If not, use a needle and clear blockage from inside
steam nozzle.
Solution: Place a large cup underneath the coffee spout. Push
the Rinse button (Fig. 3f) until the display shows RINSE. Push the
Dial (Fig. 3e) RINSING. READY. Repeat the process if necessary
until the blocked coffee is pushed into the used coffee container.
b. Clean all other frother parts and assemble properly.
c. If any parts are missing call Customer Service:
1-800-220-5701 or use the enclosed mail order form to order
the missing part.
D. GRINDER MAKES AN EXTREMELY LOUD NOISE;
NO BEANS ARE GROUND
Reason: A stone is blocking the burr grinder.
Solution: Call customer service: 1-800-220-5701.
B. THE DISPLAY READS "FILL WATER" BUT THERE IS
ENOUGH WATER IN THE WATER TANK.
Reason: The low water floatation device (Fig. 7.4) is missing.
Solution: Within the water tank is a small compartment (like a
mouse trap). Inside is a small black floatation device. On top is a
small clear see-through plastic cover. This small plastic cover is
missing and the floatation device is outside of the small com-
partment. Check if you can locate both pieces and put it back
together. If you cannot find them, call 1-800-220-5701. We will
send the pieces to you FREE OF CHARGE.
E. THE DRAWER (Fig. 19) DOESN’T PULL OUT OR DISPLAY
SHOWS MALFUNCTION 8
Solution: Turn off and unplug machine. Wait a minute. Turn
machine on and wait until it stops making any noise. Now try to
pull out the drawer. If this does not work, try the above procedure
again. If this does not work, call customer service:
23.
Download from Www.Somanuals.com. All Manuals Search And Download.
25. WARRANTY
For Home Use: Limited One Year Warranty
liability for incidental and consequential damages caused by the
machine. The terms "incidental damages" refer to the loss of the
original purchasers time, loss of the use of the machine or other
costs relating to the care and custody of the machine. The terms
"consequential damages" refer to the cost of repairing or replac-
ing other property which is damaged when this machine does
not work properly. The remedies provided under this warranty
are exclusive and in lieu of all others.This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
For Non-Home Use: Limited Six Month Warranty
This warranty covers your new IMPRESSA E Series. This warranty
is in effect for the period described above from the date of the
first consumer purchase and is limited to the United States of
America. This warranty covers all defects in materials or work-
manship (parts and labor) including UPS ground transportation
for both ways, if necessary.
This warranty does not cover:
• Any machine NOT distributed by JURA-CAPRESSO within the
United States.
• Any machine not purchased from an Authorized Dealer.
• Damage caused by accident, abuse, negligence, misuse,
improper operation or failure to follow instructions contained
in this manual.
• Any service or alteration performed by an unauthorized person,
company or association.
CUSTOMER SERVICE
1-800-220-5701
Mon-Fri 9AM – 9PM
Sat 9AM – 5PM
Eastern Standard Time.
email: [email protected]
• Damage caused by neglecting and omitting cleaning and
decalcifying cycles.
• Damage caused by use of instant coffee or any other ingredients
not allowed in this product.
This warranty will be void if the Product Registration Card is
not sent within two weeks after purchase date.
Other limitations and exclusions:
Jura-Capresso LLC.
81 Ruckman Road
Closter, NJ 07624
Any implied warranties including fitness for use and mer-
chantability are limited in duration to the period of the express
warranty set forth above and no person is authorized to assume
for JURA-CAPRESSO any other liability in connection with the
sale of the machine. JURA-CAPRESSO expressly disclaims
201-767-3999
Fax: 201-767-9684
Download from Www.Somanuals.com. All Manuals Search And Download.
|