HSIM-W87
User’s Guide
HSIM-W87
CPU
T3
TX
RX
LNK
STS
TELCO
9032689-02
Download from Www.Somanuals.com. All Manuals Search And Download.
Only qualified personnel should perform installation
procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
1998 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Part Number: 9032689-02 September 1998
Cabletron Systems and LANVIEW are registered trademarks of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
HSIM-W87 User’s Guide
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment,
radio disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT: Before utilizing this product, carefully read this License Agreement.
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (the
“Program”) contained in this package. The Program may be contained in firmware, chips or other
media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
ii
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
CABLETRON SOFTWARE PROGRAM LICENSE
1.
LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2.
3.
OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1.
EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including
its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE
ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
2.
NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,
EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR
ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer
software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the
Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects
is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the
DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its
successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.
HSIM-W87 User’s Guide
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
iv
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCTION
1.2 Overview...................................................................................... 1-2
1.4 Features ...................................................................................... 1-4
1.4.4 Priority Queuing.............................................................. 1-6
1.7 Getting Help................................................................................. 1-9
CHAPTER 2
INSTALLATION
2.2.1 Installing the HSIM-W87 in an Interface Module ............ 2-2
2.3 Connecting the HSIM-W87 to the Network.................................. 2-6
CHAPTER 3
CHAPTER 4
MANAGEMENT
4.1 Local Management...................................................................... 4-1
4.2 Network Tools.............................................................................. 4-3
4.2.1 Commands ..................................................................... 4-4
4.2.2 Built-in Commands ......................................................... 4-6
4.2.3 Special Commands....................................................... 4-13
4.3 Sample IMUX Configuration...................................................... 4-14
HSIM-W87 User’s Guide
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
CHAPTER 5
5.1.2 Investigating Software Configuration Problems .............5–3
APPENDIX A
A.1 Physical Properties ..................................................................... A-1
A.2 Environmental Requirements...................................................... A-1
A.3 Regulatory Compliance............................................................... A-2
APPENDIX B
APPENDIX C
TYPICAL CONFIGURATION
WAN TERMS AND ACRONYMS
vi
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems HSIM-W87 User’s Guide. This
manual describes the HSIM-W87 and provides information concerning
features, installation, the use of management, troubleshooting, and
specifications.
Important Notice
Depending on the firmware version used in the HSIM-W87, some
features described in this document may not be supported. Refer to the
Release Notes shipped with the HSIM-W87 to determine which features
are supported.
A general working knowledge of Wide Area Networking (WAN),
including T1 and T3 Networking, Ethernet and data communications
networks, and their physical layer components is helpful when installing
this device.
The HSIM-W87 has one T3 port, which consists of two BNC connectors,
a transmit and a receive port. Figure 1-1 shows the HSIM-W87.
HSIM-W87
T3
TX
RX
LNK
STS
CPU
TELCO
Figure 1-1 HSIM-W87
1.1
USING THIS MANUAL
Reading through this manual completely will help you understand the
features and capabilities of the HSIM-W87. The following list provides
an overview of each section of this manual:
Chapter 1, Introduction, outlines the contents of this manual, describes
the HSIM-W87 features and concludes with a web site address where
related manuals can be obtained.
HSIM-W87 User’s Guide
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
Chapter 2, Installation, describes how to install an HSIM-W87 into an
module, or standalone device, into which the HSIM-W87 can
NOTE
be installed.
Chapter 3, LANVIEW LEDs, describes how to use the HSIM-W87
Chapter 4, Management, describes the Network Tools needed for
Chapter 5, Troubleshooting, describes some of the common
Appendix A, Specifications, lists the operating specifications and
regulatory compliance of the HSIM-W87.
Appendix B, Typical Configuration, displays possible configurations for
the HSIM-W87.
Appendix C, WAN Terms and Acronyms, provides a glossary of some
terms and acronyms used in this manual.
1.2
OVERVIEW
The HSIM-W87 extends the functionality of certain Cabletron Systems
platforms by providing an interface for Wide Area Network (WAN) DS3
services. The HSIM-W87 is a High Speed Interface Module (HSIM) used
to provide WAN services using the SmartSwitch series of products as a
platform. The HSIM-W87 has a physical DS3 interface, providing up to
28 separate logical DS1 connections. The 28 T1 circuits are all capable of
acting either as a single 45 Mbps full duplex data circuit or as individual
T1 circuits within a Layer 2 Inverse Multiplexing (IMUX) group.
The typical configuration is a head-end WAN aggregation point for up to
28 T1s into a single WAN physical interface. The HSIM-W87 is able to
uplink any combination of single T1s or multiple T1 IMUX groups to the
backbone.
1-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
The HSIM-W87 has its own i960 HD microprocessor used to process data
packets, provide simple configuration, Inverse Multiplexer functionality,
and statistics processing. The SmartSwitch host platform provides the
required logical IP Host services. The HSIM-W87 is designed to be
installed in any Cabletron Systems product that supports the High Speed
Interface Module.
The HSIM-W87 operates in two modes:
•
•
Switching
IMUX
The first mode, switching, is the default mode. The HSIM-W87 forwards
data packets received by the host platform out through the logical DS1
interfaces. It also forwards packets received in the DS1 interfaces to or
through the host. The default and only layer 2 WAN protocol used with
the HSIM-W87 is raw HDLC.
The host platform may operate in 802.1D bridging, 802.1Q
VLAN, or SecureFast mode.
NOTE
Multiplexer (IMUX) functionality to aggregate multiple DS1 connections
into single higher bandwidth WAN connections. In order to operate in this
mode, the user will simply need to configure the appropriate IMUX
groups containing the DS1 connections.
Along with the built-in management features (Network Tools) described
in Chapter 4, the HSIM-W87 can be managed using SNMP, and statistical
data can be accessed via SNMP by referencing the interface group defined
in RFC-1213.
HSIM-W87 User’s Guide
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1.3
DATA FLOW IN THE HSIM-W87
The T3 port receives the DS3 data through the coaxial interface. A T3
framer/Multiplexer strips off the T3 framing and provides 28 individual
T1 data streams. The T1 data streams are then terminated by T1 framers,
which provide an HDLC bit stream to the HDLC controller. The
controller receives data packets from each of the bit streams and places
them in a memory subsystem. An onboard CPU examines the packet and
notifies the host of its arrival. Finally, a Cabletron proprietary ASIC
transfers the data to the host platform.
This process is followed in reverse when a packet is transmitted from the
host platform out the T3 port. The host platform notifies the HSIM-W87
when a packet is coming and transfers the packet to the memory. The
HDLC format is applied to the data; then the data is framed to a T1
format, and passed to the framer/ Multiplexer. The T1 data is multiplexed
with other T1 streams and is transmitted out through the T3 interface.
1.4
FEATURES
•
Data Transfer Rates of 45 Mbps in full duplex, when running all 28
T1s carrying continuous data traffic of 128-byte packets or larger.
•
•
•
•
•
•
•
High-level Data Link Control (HDLC) protocol
T1 Inverse Multiplexing (IMUX)
WAN IP Priority Queuing functionality
DS1 Alarm Thresholds
SNMP support
DS1 and DS3 MIB Support
LANVIEW LEDs
1.4.1
Connectivity
The HSIM-W87 module supports WAN technology using a DS3
interface, and supports 28 live full duplex T1 connections. The
HSIM-W87 channelizes the T3 down to the DS1 level. The HSIM-W87
has an integrated M13 MUX.
1-4
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
The primary function of the HSIM-W87 is to provide LAN to WAN
access. WAN physical connectivity will be supported through the use of a
T3 interface with an unbalanced 75 ohm coaxial cable pair. LAN to WAN
connectivity will be supported through HDLC and T1 Inverse
Multiplexing (IMUX).
The HSIM-W87 interoperates with those Cabletron Systems WAN
products that support raw HDLC as the WAN protocol. This support is
limited to the CyberSWITCH product line which supports HDLC:
•
•
•
•
CSX400 – Version 02.00.15 or higher
HSIM-W6 – Version 02.00.15 or higher
HSIM-W84 – Version 02.00.xx or higher
HSIM-W85 – Version 02.00.xx or higher
1.4.2
HDLC
The High-level Data Link Control (HDLC) protocol is used in
conjunction with the Inverse Multiplexing (IMUX) feature to conserve a
user’s WAN bandwidth between two Cabletron Systems products, over a
point-to-point connection. Cabletron Systems products such as the
HSIM-W6, HSIM-W84, HSIM-W85, HSIM-W87, and CSX400 must be
in use on both ends of the WAN link for these functions to work. The
HDLC (RAW) protocol reduces the amount of overhead information that
needs to be contained within each data packet to direct it to its destination.
This decreased packet overhead provides the IMUX functions with more
bandwidth to transfer user data.
1.4.3
Inverse Multiplexing (IMUX)
Cabletron Systems Inverse Multiplexing (IMUX) feature provides
enhanced throughput for users by doing the following:
•
The IMUX function evenly distributes a data packet stream from the
LAN interface through multiple full T1 WAN interfaces on the
HSIM-W87.
•
Data packet streams received by the WAN interfaces on the other end
of the WAN links are then recombined, ordered, and transmitted to the
LAN interface.
HSIM-W87 User’s Guide
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
•
The IMUX function is configurable using the Network Tools
command, imux, described in Chapter 4.
Cabletron Systems products that support Inverse Multiplexing
NOTE
(IMUX), such as the HSIM-W87, HSIM-W6, CSX400,
HSIM-W84, and HSIM-W85, must exist on both ends of the
WAN link for the IMUX function to work. All bridging and
switching functions, such as 802.1D, SecureFast VLAN, and
802.1Q are able to run as normal on the host platform when
using the IMUX function on the HSIM-W87.
1.4.4
Priority Queuing
WAN IP Priority Queuing is used to prioritize IP packets from a specified
network, such as management packets which are necessary to the
operation of the network, and routers that depend on protocols with tight
timing, such as RIP, do not time out. The prioritized packets do not
eliminate other traffic on the network, but are held in a special queue, so
that they are not discarded during oversubscribed traffic peaks. Priority
Queuing can be enabled in management, using Network Tools. Refer to
the wanpq command in the Management chapter.
1.4.5
DS1 Alarm
Using the DS1 Error Threshold Alarm Monitor provides a means of
setting error thresholds and notifying the user of potential DS1 problems
with SNMP trap events.
The ds1alarm Monitor feature can be enabled in management, using
Network Tools. Refer to the ds1alarm command in the Management
chapter.
1.4.6
SNMP and MIB Support
With the SNMP support, the MIBs supported by the HSIM-W87 include:
•
RFC 1406 – Definitions of Managed Objects for the DS1 and E1
Interface Types
•
RFC 1407 – Definitions of Managed Objects for the DS3/E3 Interface
Type
1-6
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Conventions
•
•
RFC 1213 (MIBII) support for the Interface Table
Cabletron Enterprise MIBs
Refer to the Release Notes included with the host platform for a list of all
MIBs supported by the HSIM-W87. For information about how to extract
and compile individual MIBs, contact the Cabletron Systems Global Call
Center (Section 1.7).
1.4.7
LANVIEW Diagnostic LEDs
Cabletron Systems provides a visual diagnostic and monitoring system
called LANVIEW. The HSIM-W87 LANVIEW LEDs help you quickly
identify status of the device. Chapter 3 provides information on the
HSIM-W87 LEDs.
1.5
DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
NOTE
Caution symbol. Contains information essential to avoid
damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action
that could result in personal injury or death due to an electrical
hazard.
Tip symbol. Conveys helpful hints concerning procedures or
actions.
TIP
HSIM-W87 User’s Guide
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
bold type
Denotes either a user input or a highlighted screen selection.
RETURN
Indicates either the ENTER or RETURN key, depending on your
keyboard.
ESC
Indicates the keyboard Escape key.
Indicates the keyboard space bar key.
SPACE bar
BACKSPACE Indicates the keyboard backspace key.
arrow keys
[-]
Refers to the four keyboard arrow keys.
Indicates the keyboard – key.
DEL
Indicates the keyboard delete key.
italic type
Italic type emphasizes important information, indicates variables,
and indicates complete document titles.
n.nn
A period in numerals signals the decimal point indicator. (e.g.,
1.75 equals one and three fourths, or the Decimal Dotted Notation
(DDN) for an IP address.
x
Indicates the generic use of a letter (e.g., xxx indicates any
combination of three alphabetic characters).
n
[]
Indicates the generic use of a number (e.g., 19nn indicates a
four-digit number in which the last two digits are unknown).
In the Local Management screens, the brackets indicate that a
value may be entered or selected. In the format descriptions in the
Network Tools section, required arguments are enclosed in [].
<>
In the format descriptions in the Network Tools section, optional
arguments are enclosed in <>.
1.6
RELATED DOCUMENTATION
The documentation for the host platform in which the HSIM-W87 is to be
installed provides additional information about the setup of the
HSIM-W87. The host documentation is not listed below, as there can be
many different host platforms. This user’s guide references procedures in
these documents, where appropriate, but does not repeat them.
Documents can be obtained on the World Wide Web in Adobe Acrobat
Portable Document Format (PDF) at the following site:
1-8
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Help
1.7
GETTING HELP
For additional support related to this device or document, contact the
Cabletron Systems Global Call Center:
World Wide Web
Phone
(603) 332-9400
Internet mail
FTP
anonymous
Login
Password
your email address
To send comments or suggestions concerning this document, contact the
Cabletron Systems Technical Writing Department via the following
Make sure to include the document Part Number in the email message.
Before calling the Cabletron Systems Global Call Center, have the
following information ready:
•
•
•
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem
(e.g., changing mode switches, rebooting the unit, etc.)
•
The serial and revision numbers of all involved Cabletron Systems
products in the network
•
•
•
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a
recurring problem, etc.)
•
Any previous Return Material Authorization (RMA) numbers
HSIM-W87 User’s Guide
1-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1: Introduction
1-10
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
INSTALLATION
To install the HSIM-W87 the following items are required:
•
•
Antistatic wrist strap (shipped with the HSIM-W87)
Phillips screwdriver
Before attempting to use the HSIM-W87 you should be familiar
with the IEEE 802.3 Specifications, and T1 and T3 Networking.
NOTE
2.1
UNPACKING THE HSIM-W87
The HSIM-W87 and the host platform are sensitive to static
discharges. Use an antistatic strap and observe all static
precautions during this procedure. Failure to do so could result
in damage to the HSIM-W87 or host platform.
!
CAUTION
Unpack the HSIM-W87 as follows:
1. Remove the HSIM-W87 from the shipping box.
2. Leave the module in its antistatic bag until you are ready to install it.
3. Attach the antistatic wrist strap (refer to the instructions on the
antistatic wrist strap package for proper use).
4. After removing the module from its antistatic bag, visually inspect the
device. If you notice any signs of damage, contact the Cabletron
Systems Global Call Center immediately. Refer to Section 1.7 for
instructions. Save the antistatic bag in the event the module must be
reshipped or relocated.
HSIM-W87 User’s Guide
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
2.2
INSTALLING THE HSIM-W87
Only qualified personnel should install or service this unit.
An HSIM-W87 can be installed in any Cabletron Systems device that
supports HSIM technology (e.g., 2H252-25R, 2E42-27, 6E132-25).
Refer to the release notes for the version of firmware running
on the Cabletron Systems host platform to ensure that the
NOTE
HSIM-W87 is supported.
The following subsections provide instructions for installing an
HSIM-W87 in a host platform. Refer to the specific interface module or
standalone device document for exact HSIM slot and connector locations.
2.2.1
Installing the HSIM-W87 in an Interface Module
To install an HSIM-W87 in an interface module that supports HSIM
technology, perform the following steps.
1. Note the ports of the interface module that have cables attached to
them. Write down the ports and label the cables to make it easier to
reattach the network properly after the installation. Then disconnect
those cables from the ports.
2. Attach the antistatic wrist strap (refer to the instructions outlined on
the antistatic wrist strap package).
3. If the interface module is installed in a chassis, unlock the top and
bottom plastic locking tabs of the module faceplate.
4. Remove the module from the chassis, and place it down flat with the
internal components facing up.
5. Remove and save the two faceplate mounting screws securing the
HSIM coverplate and remove the coverplate. See Figure 2-1.
2-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Standoff Screws
Connector
Connector
Cutaway view of connector
HSIM-W87
LNK
STS
T3
TX
RX
TELCO
HSIM-W87
CPU
SP
HSIM
Pins
Standoffs
Faceplate Mounting Screws
Interface Module
or Device
mounting
Figure 2-2 Installing the HSIM-W87
7. Align the connector on the HSIM-W87 with the pins on the module.
Ensure that the HSIM-W87 connector aligns with the module
connector pins to prevent bending the pins. This can damage
both the HSIM-W87 and the module.
!
CAUTION
8. Press down firmly on the connector area of the HSIM-W87 until the
connector slides all the way onto the pins. Ensure that the standoffs on
the interface module align with the standoff screw holes on the
HSIM-W87.
2-4
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the HSIM-W87
9. Secure the HSIM-W87 to the module faceplate using the mounting
screws saved in Step 5.
10. Secure the HSIM-W87 to the module standoffs using the standoff
screws included in the HSIM-W87 shipping materials.
11. Reinstall the interface module in the chassis.
12. Reattach the network cabling to the interface module.
2.2.2
Installing the HSIM-W87 in a Standalone Device
To install an HSIM-W87 into a standalone device (e.g., 2H252-25R)
perform the following steps:
1. Power down the device and remove the power cord.
2. Note the ports that have cables attached to them. Write down the ports
and label the cables to make it easier to reattach the network properly
after the installation. Then disconnect those cables from the ports.
To install the HSIM-W87 in a standalone device the device
must first be powered down. Ensure that you remove the power
cord and ONLY the screws required to remove the chassis
cover.
3. Attach the antistatic wrist strap (refer to the instructions outlined on
the antistatic wrist strap package).
4. Remove the standalone device chassis cover (refer to your specific
standalone device documentation for instructions on removing the
chassis cover).
5. Refer back to Figure 2-1 and remove the two faceplate mounting
screws and the HSIM coverplate. Save the screws.
6. Refer back to Figure 2-2 and place the HSIM-W87 behind the
standalone device faceplate.
7. Align the HSIM connector of the HSIM-W87 with the pins on the
standalone device.
HSIM-W87 User’s Guide
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2: Installation
Ensure that the HSIM-W87 connector aligns with the device
connector pins to prevent bending the pins. This can damage
both the HSIM-W87 and the device.
!
CAUTION
8. Press down firmly on the HSIM-W87 until the connector slides all the
way onto the HSIM pins. Ensure that the standoffs on the standalone
device align with the standoff screw holes on the HSIM-W87.
9. Secure the HSIM-W87 to the module faceplate using the mounting
screws saved in Step 5.
10. Secure the HSIM-W87 to the module standoffs using the standoff
screws included in the HSIM-W87 shipping materials.
Ensure that the chassis cover is in place before reconnecting
the power cord.
11. Replace the chassis cover on the standalone device, reconnect the
power cord, and reconnect the standalone device to the network.
2.3
The HSIM-W87 is connected to the carrier’s DS3 service using coaxial
cable. The 75 Ohm unbalanced coaxial cable may be run a maximum of
450 feet. For typical configurations for the HSIM-W87, see Appendix B.
2.4
HSIM-W87 SETUP
See Chapter 3 for information on the LEDs, Chapter 4 on how to set up
the HSIM-W87 in management, and Chapter 5 for Troubleshooting.
2-6
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 3
LANVIEW LEDs
3.1
LANVIEW LEDS
This chapter describes how to use the LANVIEW LEDs to monitor the
HSIM-W87 status and diagnose HSIM-W87 problems. Figure 3-1 shows
the location of the HSIM-W87 LEDs.
Link
HSIM-W87
T3
TX
RX
LNK
STS
CPU
TELCO
Status
CPU
w87_LEDs
Figure 3-1 HSIM-W87 LANVIEW LEDs
The terms flashing, blinking, and solid used in Table 3-1
indicate the following:
NOTE
Flashing indicates an irregular LED pulse.
Blinking indicates a steady LED pulse (approximately 50% on
and 50% off).
Solid indicates a steady LED light. No pulsing.
HSIM-W87 User’s Guide
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3: LANVIEW LEDs
Table 3-1 HSIM-W87 LEDs
LED
Color
Definition
Off
Power Off
Processor
(CPU)
Green (solid)
Red (solid)
Red
Fully operational
System in reset mode (temporary)
No Link or Receive signal
Traffic on at least one port
Link but sync may not be present
Normal
Link (LNK)
Amber
Green
Off
Red
Red Alarm
Status
(STS)
Green (blinking)
Amber
Receiving Blue Alarm
Yellow Alarm
Amber (blinking)
Port is performing diagnostics
3-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 4
MANAGEMENT
This chapter describes Local Management and the Network Tools utility.
Local Management allows access to statistics screens that apply to the
HSIM-W87 through the host platform. Network Tools allows access to a
command set from which you can configure and manage the HSIM-W87.
This chapter provides the following information:
•
•
•
Overview of Local Managment, Section 4.1
Network Tools used with the HSIM-W87, Section 4.2
Sample IMUX configuration, Section 4.3
4.1
LOCAL MANAGEMENT
Access to Local Management screens and Network Tools is
NOTE
obtained by using Local Management on the host platform.
Refer to the host platform user’s guide to establish a Local
Management connection, and for information on the screens.
Make sure that the following requirements have been met before
accessing the HSIM-W87 through Local Management:
•
•
A management terminal is properly configured and connected, either
locally or using Telnet, to the host platform in which the HSIM-W87
resides. Refer to the host platform document for further information.
In order to view the HSIM-W87 statistics screens, you must navigate
through a series of Local Management screens via the host platform.
Figure 4-1 shows a typical hierarchy of screens that you would navigate
through in order to reach the HSIM-W87 screens. The lines shown in
boldface indicate a typical path used to access the HSIM-W87 statistics
screens.
HSIM-W87 User’s Guide
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
General Configuration
Device
Configuration
Menu
SNMP Community Names Configuration
SNMP Traps Configuration
System Resources Information
Flash Download Configuration
Password
Port Configuration
Menu
Ethernet Interface
Configuration
HSIM/VHSIM
Configuration
802.1 Configuration
Menu
Device
Menu
Port Redirect
Configuration
Switch Configuration
Flow Control
Configuration
802.1Q VLAN
Configuration Menu
SmartTrunk
Configuration
Device/VLAN
Configuration
Broadcast
Suppression
Configuration
Port Assignment
Configuration
Port Filtering
Configuration
VLAN Forwarding
Configuration
802.1p Priority
Configuration Menu
Port Priority
Configuration
Advanced Port
Priority
Configuration
Device
Statistics
Menu
Switch Statistics
Interface Statistics
RMON Statistics
HSIM/VHSIM
Statistics
Network Tools
2555hier
Figure 4-1 Typical Hierarchy of Local Management Screens
Different versions of the firmware may display a different
hierarchy. Check the host platform manual if the hierarchy
displayed does not match the one in Figure 4-1.
NOTE
The HSIM/VHSIM Statistics menu option underneath the
Device Statistics Menu applies to the non-Ethernet HSIMs or
VHSIMs such as ATM or FDDI, but not the HSIM-W87.
4-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
Important Notice
The HSIM-W87 statistics that are accessed using the Switch and
Interface Statistics screens are not explained in this manual. Refer to the
applicable host platform manual for details. “T3 Interface” and “T1
Interface” will be displayed as the name of the HSIM-W87 interface in the
statistics screens.
4.2
NETWORK TOOLS
The Network Tools utility allows management of objects in the
HSIM-W87 Management Information Bases (MIBs). MIBs are databases
of objects used for managing the device and configuring the HSIM-W87.
The commands within the MIB Navigator allow the user to view and
modify a device’s objects.
The host platform contains either the Network Tools utility, or the MIB
Navigator utility. They are essentially the same tool, with some minor
differences depending on the platform. They will both be referred to as
Network Tools in this document, and there is no difference in their use for
the purpose of this document. Using Network Tools may be a more
convenient method for a user to configure the HSIM-W87 than using the
MIBs in some circumstances. Full functionality is still available by using
the MIBs. The host platform has a set of functions for Network Tools that
are used on that platform. The following additions to the Network Tools
utility from the WAN perspective are specific to the HSIM-W87, and can
only be used when a HSIM-W87 is installed in the platform.
•
•
•
imux – support for configuration and monitoring of the Inverse
Multiplexer (ctwan-multi-imux-mib.txt, Revision 1.00.00)
ds1alarm – support for ds1 alarm monitoring (ctremote-mib.txt,
Revision 1.00.02, Ds1Alarms branch)
wanpq – support for Wan IP Priority Queuing (ctremote-mib.txt,
Revision 1.00.02, ctIPPQFilters branch)
•
•
dsx1 – support for RFC 1406 statistics and configuration
dsx3 – support for RFC 1407 statistics and configuration
Only the above commands, that are particular to the HSIM-W87, will be
described in the following sections. The host platform’s manual describes
the other commands that are not particular to the HSIM-W87. Refer to the
host platform manual for information on the other commands.
HSIM-W87 User’s Guide
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
4.2.1
Commands
The Network Tools function resides on the host platform and allows the
user to access and manage network devices. Figure 4-2 shows the
Network Tools Help screen. Screens may be slightly different depending
on the host platform and the version of firmware.
To access the Network Tools screen, access Local Management, then use
the arrow keys to navigate to and highlight the NETWORK TOOLS
menu item in the appropriate menu screen and press ENTER. The
Network Tools Help screen displays. Refer to the host platform manual
for details on accessing Local Management.
Type help at the prompt to list all the commands that are
available for the device in the current operational mode. If help
is needed with a specific command, type help and the
<command>. Use lower case characters when entering
commands in Network Tools. Uppercase characters may be
specified for some of the options. A command used incorrectly
(wrong syntax or case) will prompt a display of the correct
usage.
TIP
-> help
Commands Available to the User:
Built in Commands:
bridge
ping
defroute
reset
arp
netstat
show
traceroute
telnet
soft_reset
imux
link_trap
wanpq
ds1alarm
dsx3
dsx1
SPECIAL:
done, quit, or exit - Exit from the Network Tools.
For help with a specific command, type 'help <command>'.
->
090829
Figure 4-2 Network Tools Help Screen
4-4
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
The Network Tools functions are performed using a series of commands.
Entering commands in Network Tools involves typing the command at the
Network Tools prompt, adding any required parameters, and pressing
ENTER to execute the command.
There are two categories of commands in the command set.
•
Built-in Commands – Allow the user to access and manage network
devices. The commands for the HSIM-W87 are imux, ds1alarm,
wanpq, dsx1, and dsx3. The other commands listed in Figure 4-2 are
described in the host platform manual.
•
Special Commands – Allow the user to exit from Network Tools. The
commands are done, exit, and quit. All three commands perform the
exact same function.
The conventions used in describing the commands in Network
Tools are as follows:
NOTE
Arguments enclosed by [ ] are required.
Arguments enclosed by < > are optional.
In the following command examples, the information entered by
the user is shown in bold Helvetica font.
To abort the output or interrupt a process, press the CONTROL
key and c key simultaneously, designated as ^C here.
The commands are presented in the following format:
command:
Syntax:
Shows the required command format. It indicates where
arguments, if any, must be specified.
Description: Briefly describes the command and its uses.
Options:
Lists any additional fields in the appropriate format that
may be added to the command.
Example:
Shows an example of how to use the command.
HSIM-W87 User’s Guide
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
4.2.2
Built-in Commands
The built-in commands listed in this section activate configuration and
viewing functions on the HSIM-W87.
imux:
Cabletron Systems products that support Inverse Multiplexing
(IMUX), such as the HSIM-W87, HSIM-W6, CSX400, and
NOTE
HSIM-W84, must exist on both ends of the WAN link for the
IMUX function to work. All bridging and switching functions,
such as 802.1D, SecureFast VLAN, and 802.1Q are able to run
as normal on the host platform when using the IMUX function
on the HSIM-W87.
Syntax:
imux <IMUXID>
imux <IMUXID> -[ea | da]
imux <IMUXID> -[eg | dg] <GROUPID>
imux <IMUXID> -[ac | dc] <GROUPID>
<INTERFACENUM>
Description: imux is used to combine multiple WAN channels into
logical inverse multiplexing (IMUX)groups. Once the
IMUX is configured, data will be evenly distributed over
all of the logical channels configured.
<IMUXID> - A unique value identifying an element in a
sequence of Inverse Multiplexer Applications which
belong to an IP host.
<GROUPID> - A unique value identifying an element in
a sequence of groups which belong to a WAN Inverse
Multiplexer Application.
<INTERFACENUM> - The MIB II ifIndex value used to
represent a WAN channel that has an appropriate datalink
protocol associated with it.
4-6
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
Options:
imux <IMUXID> (with no options) displays status
information.
-ea enables the Inverse Multiplexer Application
designated by IMUXID.
-da disables the Inverse Multiplexer Application
designated by IMUXID.
-eg <GROUPID> enables the Inverse Multiplexer group
designated by GROUPID.
-dg <GROUPID> disables the Inverse Multiplexer group
designated by GROUPID.
-ac <GROUPID> <INTERFACENUM> Adds the WAN
channel designated by INTERFACENUM to the Inverse
Multiplexer group designated by GROUPID.
-dc <GROUPID> <INTERFACENUM> Deletes the
WAN channel designated by INTERFACENUM from the
Inverse Multiplexer group designated by GROUPID.
Example:
-> imux 1 -ac 1 29
# Inverse Multiplexer channel with ifIndex 29 added to group 1
-> imux 1
#
# WAN Inverse Multiplexer 1 Status: Disabled
#
#
Inverse
WAN
Available Xmit Byte
BW Count
(bits/sec) (bytes)
Inverse
# Multiplexer Group Physical
# ID Admin Status Number
Multiplexer Channel
ID IfIndex Status
#-------------------------------------------------------------------------------------------------------------
#
#
#
1
Disabled
22
1536000
0
1
29
INACTIVE
# Number of WAN Inverse Multiplexer Groups currently programmed : 1
#
# Number of WAN Inverse Multiplexer Channels currently programmed : 1
imuxsetup1
HSIM-W87 User’s Guide
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
command:
Syntax:
wanpq
wanpq
wanpq -ea
wanpq -da
wanpq -aip <IPADDRESS>
wanpq -dip <IPADDRESS>
Description: WAN IP Priority Queuing is used to prioritize IP packets
from a specified IP address. <IPADDRESS> - The
Internet Protocol (IP) address being added to or removed
from the Wide Area Network Priority Queue database.
Options:
wanpq (with no options) displays information on the
status of the WAN priority queue.
-ea enables the WAN Priority Queue Application.
-da disables the WAN Priority Queue Application.
-aip <IPADDRESS> Adds the IP address designated by
IPADDRESS to the WAN Priority Queue database.
-dip <IPADDRESS> Deletes the IP address designated by
IPADDRESS from the WAN Priority Queue database.
Example:
-> wanpq
#
#WAN Priority Queue Status: Disabled
#
#Maximum number of address entries: 16
#
#Current number of address entries programmed: 0
#
-> wanpq -ea
#
# WAN Priority Queue Application enabled.
->
2689_1
4-8
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
command:
Syntax:
ds1alarm
ds1alarm
ds1alarm -[ea | da] <WANID>
ds1alarm -[et | dt] <WANID>
ds1alarm -sec <WANID> <VALUE>
ds1alarm -sei <WANID> <VALUE>
ds1alarm -mr <WANID>
Description: The ds1alarm function allows the user to set error
thresholds in order to set traps and monitor the operation
and recovery of a device.
<WANID> This option is either ALL to apply command
to all DS1 circuits, or the specific WAN physical identifier
associated with the DS1 circuit.
Options:
ds1alarm (with no options) displays information on the
error thresholds.
-ea enables the WAN DS1 Alarms Admin.
-da disables the WAN DS1 Alarms Admin.
-et enables the WAN DS1 Alarms Traps Feature.
-dt disables the WAN DS1 Alarms Traps Feature.
-sec sets the Errored Seconds Threshold Count to
VALUE.
-sei sets the Errored Seconds Threshold Interval to
VALUE.
-mr manually recovers a DS1 link that has exceeded a
threshold.
Example:
-> ds1alarm
#--------------------------------------------------------------------------------------------------------------------------
DS1 Alarm Thresholds
#
#--------------------------------------------------------------------------------------------------------------------------
# HSIM
DS1
DS1
ID
Admin
Status
Trap
ES
ES
#
#
ID
Index
Admin
Count
Interval
(minutes)
#--------------------------------------------------------------------------------------------------------------------------
#
#
#
#
#
#
#
1
1
1
1
1
1
1
1
2
3
4
5
6
7
29
30
31
32
33
34
35
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
100
100
100
100
100
100
100
6
6
6
6
6
6
6
----More----
2689_2
HSIM-W87 User’s Guide
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
command:
Syntax:
dsx1
dsx1
dsx1 near
dsx1 near <1..96>
dsx1 linetype <ESF|D4> <line>
dsx1 loopback <no|payload|line> <line>
dsx1 txclksrc <loop|local> <line>
dsx1 <line>
dsx1 <line>
<ES|SES|SEFS|UAS|CSS|PCV|LES|BES|DM|LCV>
Description: This command allows the user to read the contents of
several tables defined in RFC 1406.
“line”, as an option, refers to the number of an instance of
a physical T1 interface. A different “line” is in the choice
between no, payload, and line for the loopback function.
The acronyms in caps refer to error types defined in the
RFC. Refer to RFC1406 for more information.
<1..96> is the number of a previous 15 minute
measurement interval in the table. Interval “1” is always
the latest interval to have taken place, with interval “2” as
the next latest, etc.
Near indicates the device on your side of the WAN line.
Options:
dsx1 (with no options) lists a summary of the DS1
configuration.
dsx1 near lists a summary of the statistics for the device
on your side of the WAN line.
dsx1 near <1..96> lists a summary of the statistics for the
device on your side of the WAN line for a specific time
interval.
dsx1 linetype <ESF|D4> <line> allows a choice of either
ESF or D4 linetype (framing).
dsx1 loopback <no|payload|line> <line> allows a choice
of either no, payload, or line loopback.
dsx1 txclksrc <loop|local> <line> allows a choice of
either loop or local transmit clock source.
dsx1 <line> displays the setup for the line specified.
dsx1 <line>
<ES|SES|SEFS|UAS|CSS|PCV|LES|BES|DM|LCV>
allows the choice of performance parameters.
4-10
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
Example:
-> dsx1
DS1 1406 Configuration:
LIne
Time
Intvl
Type
Coding
LoopCfg
Status
TxClk
FDL
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
504
504
504
504
504
504
504
504
504
504
505
505
505
505
505
505
505
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
ESF
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
B8ZS
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
NoLoop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
OtherFailure loop
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
Fdlnone
----More----
2689_2
command:
Syntax:
dsx3
dsx3
dsx3 near
dsx3 near <1..96>
dsx3 linetype <M23|CBITPARITY> <line>
dsx3 loopback <no|payload|line> <line>
dsx3 txclksrc <loop|local> <line>
dsx3 <line>
dsx3 <line>
<PES|PSES|SEFS|UAS|LCV|PCV|LES|CCV|CES|CSES
>
Description: Allows the user to read the contents of several tables
defined in RFC 1407.
“line” refers to the number of an instance of a physical
DS3 interface. A different “line” is in the choice between
no, payload, and line for the loopback function. The
acronyms in caps refer to error types defined in the RFC.
<1..96> is the number of a previous 15 minute
measurement interval. Interval “1” is always the latest
interval to have taken place, with interval “2” as the next
latest, etc.
HSIM-W87 User’s Guide
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
Options:
dsx3 (with no options) lists the dsx3 configuration.
dsx3 near lists a summary of the near end setup statistics.
dsx3 near <1..96> lists a summary of the near end setup
statistics for the interval specified.
dsx3 linetype <M23|CBITPARITY> <line> allows a
choice between the types of parities, M23 and Cbit for the
linetype of the line specified.
dsx3 loopback <no|payload|line> <line> allows a choice
of loopback between the listed choices for the line
specified.
dsx3 txclksrc <loop|local> <line> allows a choice of
either loop or local transmit clock source.
dsx3 <line> displays a summary of the line specified.
dsx3 <line>
<PES|PSES|SEFS|UAS|LCV|PCV|LES|CCV|CES|CSES
> allows a choice of performance parameters for the line
specified, accumulated in 15 minute intervals.
Example:
-> dsx3
Line
27
->
Time
680
Intvl
1
Type
CBPar
Coding
B3ZS
LoopCfg
NoLoop
Status
TxClk
LossOfSignallocal
2689_5
4-12
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Tools
4.2.3
Special Commands
done, quit, exit:
Syntax:
done
quit
exit
Description: The done, exit, or quit command enables the user to exit
from Network Tools and return to the Main Menu screen.
All three commands perform the same function.
Options:
Not Applicable
Example:
-> done
051472
To find the MIB II interface indexes assigned to the ds1
channels used in the IMUX group, utilize the dsx1 and
TIP
ds1alarm commands. With the dsx1 command, the interface
numbers are in the column under “line” in the display. When the
ds1alarm command is used, the interface numbers, as well as
the HSIM ID and the ds1 index, can be seen for verification.
HSIM-W87 User’s Guide
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
4.3
SAMPLE IMUX CONFIGURATION
The following is a sample of a common configuration.
To perform an IMUX configuration for the setup shown in Figure B-1, in
1. To add channels to an IMUX group:
Enter: imux 1 -ac 1 29
(this adds interface 29 to the group id 1 in the imux id 1)
To display the setup so far:
Enter: imux 1
Figure 4-3 shows the imux setup for group id 1 so far:
-> imux 1 -ac 1 29
# Inverse Multiplexer channel with ifIndex 29 added to group 1
-> imux 1
#
# WAN Inverse Multiplexer 1 Status: Disabled
#
#
Inverse
WAN
Available Xmit Byte
BW Count
(bits/sec) (bytes)
Inverse
# Multiplexer Group Physical
# ID Admin Status Number
Multiplexer Channel
ID IfIndex Status
#-------------------------------------------------------------------------------------------------------------
#
#
#
1
Disabled
22
1536000
0
1
29
INACTIVE
# Number of WAN Inverse Multiplexer Groups currently programmed : 1
#
# Number of WAN Inverse Multiplexer Channels currently programmed : 1
imuxsetup1
Figure 4-3 Adding Channels to an IMUX Group
4-14
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Sample IMUX Configuration
2. After all the desired channels have been added to the group (four were
put in the group in this example), the group must be enabled:
Enter: imux 1 -eg 1
The screen shows the response to the imux command to enable
group 1 in Figure 4-4.
-> imux 1
#
# WAN Inverse Multiplexer 1 Status: Disabled
#
#
Inverse
WAN
Available Xmit Byte
BW Count
(bits/sec) (bytes)
Inverse
# Multiplexer Group Physical
# ID Admin Status Number
Multiplexer Channel
ID IfIndex Status
#-------------------------------------------------------------------------------------------------------------
#
#
#
#
#
#
1
1
1
1
Disabled
Disabled
Disabled
Disabled
21
22
23
24
1536000
1536000
1536000
1536000
0
0
0
0
1
2
3
4
28
29
30
31
INACTIVE
INACTIVE
INACTIVE
INACTIVE
# Number of WAN Inverse Multiplexer Groups currently programmed : 1
#
# Number of WAN Inverse Multiplexer Channels currently programmed : 4
-> imux 1 -eg 1
# Inverse Multiplexer group 1 enabled.
imuxsetup2
Figure 4-4 Enabling the IMUX Group
3. The next step is to enable the imux application for imux 1:
Enter: imux 1 -ea
The screen in Figure 4-5 displays the response to the command.
HSIM-W87 User’s Guide
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4: Management
->imux 1 -ea
# Inverse Multiplexer Application 1 enabled.
-> imux 1
# WAN Inverse Multiplexer 1 Status: Enabled
#
#
Inverse
WAN
Available Xmit Byte
BW Count
(bits/sec) (bytes)
Inverse
# Multiplexer Group Physical
# ID Admin Status Number
Multiplexer Channel
ID IfIndex Status
#-------------------------------------------------------------------------------------------------------------
#
#
#
#
#
#
1
1
1
1
Enabled
Enabled
Enabled
Enabled
21
22
23
24
1536000
1536000
1536000
1536000
0
0
0
0
1
2
3
4
28
29
30
31
INACTIVE
INACTIVE
INACTIVE
INACTIVE
# Number of WAN Inverse Multiplexer Groups currently programmed : 1
#
# Number of WAN Inverse Multiplexer Channels currently programmed : 4
->
imuxsetup3
Figure 4-5 Enabling the IMUX Application
This configuration is complete. More groups can be added as needed. The
commands dsx1 and/or ds1alarm can be used to verify the interface
numbers configured. Done, exit, or quit may be used after verification to
leave Network Tools.
4-16
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 5
TROUBLESHOOTING
5.1
TROUBLESHOOTING THE HSIM-W87
Problems in setup can occur in hardware, software, or firmware setups.
The following sections detail some of the problems encountered and the
possible solution. If a problem persists, contact the Cabletron Systems
Global Call Center. Refer to Section 1.7.
5.1.1
Hardware Troubleshooting
No LEDs on
•
•
Check the host platform to see if it is powered up.
Check that the HSIM-W87 has been connected correctly, that the
connectors have no bent pins.
Link (LNK) LED is OFF
The WAN interface is not configured for operation. Power is off or the
HSIM-W87 is not connected properly.
Link (LNK) LED is RED — The WAN interface is configured, but there
is no signal indicating that a valid connection is present on the WAN
interface.
•
•
Check that the device at the other end of the segment is powered up.
Use management to make sure that both WAN interfaces, local and
remote, are configured correctly.
•
•
Check to ensure that the correct cable is being used.
Check to ensure that the cable has continuity and is installed correctly.
The cabling between the HSIM-W87 and the M13 should be checked,
and the cabling between the M13 and the devices at the far end should
also be checked.
•
Check with the WAN Service Provider to ensure that the circuit has
been configured by them and is active.
HSIM-W87 User’s Guide
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting
It may be necessary to provide proof of proper configuration of
NOTE
your WAN connection. Service Providers typically require proof
that the customer’s equipment is configured correctly before
checking their own configuration.
Status (STS) LED is OFF
The port is operating normally. If it is not, and this LED is OFF, the port
may be disabled. Use management to make sure that the WAN interface
on the HSIM-W87 is configured correctly.
Status (STS) LED is RED
A RED alarm indicates that the WAN connection is not receiving proper
framing or has lost framing from the remote device.
•
•
Verify the framing, zero suppression, and T3 clock source.
Verify the use of proper cabling on the WAN connection.
Status (STS) LED is AMBER
The device is in Yellow alarm mode. A Yellow alarm indicates that the
HSIM-W87 is receiving proper framing from the Telco, but the Telco is
not receiving proper framing.
•
Check for faulty or incorrect cabling between the Telco and the
HSIM-W87.
•
Request that the Telco verify the configuration and operation of the
circuit.
Status (STS) LED is AMBER (blinking)
Device is in test mode.
•
•
The HSIM-W87 is running its Power-up Diagnostic Tests.
Loopback Testing is underway on a WAN circuit. Loopback testing
can be initiated by the Telco.
5-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting the HSIM-W87
5.1.2
Investigating Software Configuration Problems
Software problems usually occur when your software configuration
contains incomplete or incorrect information.
Device not forwarding packets
•
Ensure that the proper DS1 transmit clock source is configured using
the dsx1 command in Network Tools.
When connecting two ds1 devices, one must be tx clock master
(local timing) and the other must be slave (loop timing).
NOTE
•
•
Check the DS1 line type. The default is ESF but some devices may be
configured for D4. Ensure that the local and remote DS1 devices are
configured with the same line (Framing) type.
Ensure that the DS1 loopback is not configured (default is none) using
the dsx1 command.
5.1.3
Problems with the Firmware Image
The firmware image for the HSIM-W87 is supported on the host platform,
therefore, if there is a problem with the firmware image for the
HSIM-W87, the image for the platform must be downloaded. Refer to the
host platform user’s guide for information on this procedure.
HSIM-W87 User’s Guide
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5: Troubleshooting
5-4
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
SPECIFICATIONS
This chapter lists the specifications and regulatory requirements for the
HSIM-W87. Cabletron Systems reserves the right to change these
specifications at any time without notice.
A.1 PHYSICAL PROPERTIES
WAN Interface
DS3 T3 port
Physical Interface
Cable Type
BNC connectors
75 Ohm unbalanced Coaxial cable
450 feet (137 m)
Maximum Link Distance
9310039-10ft
9310039-xx
T3 Cable Part Number
Microprocessor
Power Supply
i960HD66
+5V supplied by host device
18.75 Watts maximum
Power Consumption
8 MB of DRAM Local memory
4 MB of DRAM Shared memory
Memory
4.8H x 20.6W x 28.7D (cm)
1.9H x 8.1W x 11.3D (in)
Dimensions
Weight
0.45 kg (1.0 lb)
200,000 hours
MTBF (Predicted)
A.2 ENVIRONMENTAL REQUIREMENTS
Operating Temperature
Storage Temperature
5°C to 40°C (41°F to 104°F)
-30°C to 90°C (-22°F to 194°F)
5% to 95% (non-condensing)
Operating Relative Humidity
HSIM-W87 User’s Guide
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A: Specifications
A.3 REGULATORY COMPLIANCE
This equipment meets the following safety and electromagnetic
compatibility (EMC) requirements:
UL 1950 and CSA C22.2 No. 950
Safety
Electromagnetic
Compatibility
(EMC)
FCC Part 15, EN 55022, CSA C108.8, EN 50082-1,
VCCI V-3, 89/336/EEC, and AS/NZS 3548
A-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
Typical configuration is a head-end WAN aggregation point for up to 28
combination of single T1s or multiple T1 IMUX groups to the backbone.
The HSIM-W87 has an internal M13, and the Telco side M13, as shown
in Figure B-1, is supplied for CPE aggregation. The HSIM-W84 in the
diagram can be any device that is compatible with the HSIM-W87, which
runs HDLC WAN protocol.
In Figure B-1, the 2E42-27 is used as an example platform. It
could be any platform into which the HSIM-W87 can be
NOTE
installed.
HSIM-W87 User’s Guide
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B: Typical Configuration
2E42-27 with an HSIM-W87
T3
Telco Cloud
M13
28 T1 Lines
2E42-27s with HSIM-W84s
CSX400
CSX400
CSX400
T1 Configuration
configW87
IMUX Configuration
Figure B-1 HSIM-W87 IMUX Operational
B-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
WAN TERMS AND ACRONYMS
This appendix provides definitions for WAN terms and acronyms.
AIS — Alarm Indication Signal, The DS3 AIS is framed with “stuck
stuffing”. This implies that it has a valid M-subframe alignment bits,
M-frame alignment bits, and P bits. The information bits are set to a
1010... sequence, starting with a one (1) after each M-subframe alignment
bit., M-frame alignment bit, X bit, P bit, and C bit. The C bits are all set to
zero giving what is called “stuck stuffing”. The X bits are set to one. The
DS3 AIS defect is declared after DS3 AIS is present in contiguous
M-frames for a time equal to or greater than T, where
0.2 ms<=T<=100 ms. The DS3 AIS defect is terminated after AIS is
absent in contiguous M-frames for a time equal to or greater than T.
AMI — Alternate Mark Inversion, line coding used with both E-1 and T1.
A digital 1 is encoded as a “mark” (pulse) and a 0 is encoded as a “space.”
The marks alternate polarity.
ANSI — American National Standards Institute, the US member of the
ISO.
Bearer (B) Channel — A 64 Kbps channel used with BRI and PRI
ISDN services.
BPV — Bipolar Violation, the occurrence of two successive pulses of the
same polarity in a bipolar signal.
B3ZS — Bipolar with 3 Zero Substitution, an AMI line code with the
substitution of a unique code to replace occurrences of three consecutive
zero signal elements.
B8ZS — Binary 8-Zero Substitution, line coding utilized with ESF
(Expanded Super Frame) using a bipolar DS1 signal. Insures the ones
density requirement for digital T-carrier facilities in the public network,
while allowing 64 Kbps clear data per channel. This encoding method is
not supported by some Telcos.
BER — Bit Error Ratio, errored bits over total bits, should be <10–7 for
transmission lines.
HSIM-W87 User’s Guide
C-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: WAN Terms and Acronyms
BRI — Basic Rate Interface, minimum rate ISDN subscriber interface,
provides 2 B + 1 D channels (two 64 Kbps “B” (Bearer) channels and one
16 Kbps “D” (Data) signaling channel for a total of 144 Kbps).
BRIM — Cabletron Systems Bridge Router Interface Module. Expands
the physical connectivity of a host platform.
CPE — Customer Premises Equipment.
CRC — Cyclic Redundancy Check, an algorithm or process used to
identify corrupted packets in the transmission link.
CSU — Channel Service Unit, a device that terminates the local
loop/digital channel on a customer’s (DSU) premises. The CSU connects
to a DSX-1 interface on the CPE.
DCE — Data Communications Equipment, a device such as a modem
that connects the communications circuit with the end device (see DTE).
CPE — Customer Premises Equipment, Telecommunications
equipment on the customer site, such as CSU/DSUs, PBXs, etc., that
reside past the network interface.
Data (D) Channel — A 16 Kbps channel used with BRI and PRI
services for signaling and control.
D4 — D4 Framing, a popular framing format in T1. Uses 12 T1 Frames
to identify both the channel and the signaling bit.
DI — Drop and Insert, a function provided on the Cabletron Systems
WPIM-DI which allows the user to map timeslots that are not being used
to another WAN device.
DLCI — Data Link Connection Identifier, a unique virtual circuit
identifier used in Frame Relay. Identifies a given frame as being from a
particular logical link. The DLCI has only local significance.
DSU — Digital Service Unit, converts RS-232 or other terminal
interfaces to DSX-1 (T1) interface.
DS0 — Digital Signal, level 0, a standard 64,000 bit/second channel.
Synonymous with “Timeslot.”
DS1 — Digital Signal level one, the rate of transmission for a T1 line,
running at 1.544 Mbps.
DS3 — 28 T1s.
C-2
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN Terms and Acronyms
DSX-1 — Short-haul version of DS1(coaxial cable being used as the
media defines it as short-haul) by definition, coaxial cable is short-haul.
DSX-3 — Short-haul version of DS3 (coaxial cable being used as the
media defines it as short-haul) by definition, coaxial cable is short-haul.
DTE — Data Terminal Equipment, equipment that originates and
terminates data transmission such as a computer or printer (see DCE).
E-1 — European digital signal level 1. Similar to T1 but provides 32
channels (2.048 Mbps) instead of 24 channels (1.544 Mbps).
ESF — Extended Super Frame. A new T1 framing standard (see D4
framing) that uses 24 T1 frames, thus allowing individual identification of
the channel and signaling bits.
EXZ — Excessive Zeros, an EXZ is the occurrence of any zero string
length equal to or greater than 3 for B3ZS, or greater than 4 for HDB3.
Fractional T1 — Use of a portion (less than the full 24 channels) of a T1
line.
Frame Relay — A network protocol that allows for many point-to-point
virtual connections over a single access channel.
HDB3 — High Density Bipolar 3, used with E-1, a bipolar coding
method that does not allow more than 3 consecutive zeros.
HDLC — High-Level Data Link Control, layer 2 (link layer) full-duplex
protocol derived from SDLC.
INV. HDLC — A form of zero suppression in which all zeros in the
HDLC packet are changed to ones and all ones are changed to zeros.
ISDN — Integrated Services Digital Network. Allows point-to-point
connections at 64 Kbps or 128 Kbps when necessary and disconnects the
line when not in use. With this service the user only pays for the time
connected.
JBZS — Jam Bit-Zero Suppression, a form of zero suppression that
places a one in the seventh bit of a timeslot. Reduces the effective
throughput to 56 Kbps.
HSIM-W87 User’s Guide
C-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: WAN Terms and Acronyms
LCV — Line Coding Violation, a count of both BPVs and EXZs
occurring over the accumulation period. An EXZ increments the LCV by
one regardless of the length of the zero string.
LEX — LAN Extender, a Cisco Systems protocol used to internetwork a
host-based router with a remote switch.
LMP — Link Management Protocol, used in Frame Relay. Allows the
device to gather information about the DLCIs (Data Link Connection
Identifiers) See T1.617-D, Q.933-A.
Local Timing — Timing for digital transmission circuit is internally
generated by a source within the equipment. Usually used for short haul
private lines. In this case one CSU must be set for Local (internal) timing
and the CSU at the other end of the line must be set for Loop (recovered)
timing to create a master-slave situation.
Loop Timing — Timing for digital transmission circuit is recovered
from the received data, not generated internally by a source within the
equipment. This is the typical situation when using public lines. Also may
be referred to as clock slave timing.
LLB — Line Loop Back, a full T1 loopback on D4 or ESF framed lines.
LOS — Loss of Signal, DS3 signal where a predetermined amount of
pulses without polarity are deemed a defect.
M13 — (pronounced M-one-three) DS1 into a DS3 multiplexer.
MIM — Media Interface Module, Cabletron Systems products designed
to fit in a Multi Media Access Center (MMAC) hub.
MUX — Multiplexer, an electronic device that allows two or more
signals to pass over one communications circuit.
NI — Network Interface.
OOF — Out of Frame, a DS3 OOF defect is detected when any three or
more errors in sixteen or fewer consecutive F-bits occur within a DS3
M-frame. An OOF defect may also be called a Severely Errored Frame
(SEF) defect. An OOF defect is cleared when reframe occurs. A DS3 Loss
of Frame (LOF) failure is declared when the DS3 OOF defect is
consistent for 2 to 10 seconds. The DS3 OOF defect ends when reframe
occurs. The DS3 LOF failure is cleared when the DS3 OOF defect is
absent for 10 to 20 seconds.
C-4
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
WAN Terms and Acronyms
PLB — Payload Loop Back, ESF loopback including the facilities
datalink.
Point of Presence — The point between the carrier provided equipment
and services and the customer provided equipment and services.
PPP — Point-to-Point Protocol, provides a method for transmitting
datagrams over serial point-to-point links.
PRI — Primary Rate Interface, an ISDN service providing 23 “B”
(Bearer) channels of 64 Kbps and one 64 Kbps “D” (Data) channel for
signaling and control.
PVC — Permanent Virtual Circuit, a virtual circuit that provides the
equivalent of a dedicated private line service.
Q.933-A — Q.933 Annex A, an ITU link management protocol
specification used in Frame Relay.
RAI — Remote Alarm Indicator, is declared in C-bit Parity DS3
applications, after detecting the Yellow Alarm Signal on the alarm
channel.
SDLC — Synchronous Data Link Control, layer 2 (link layer) protocol
developed by IBM for SNA connectivity. Basis for HDLC.
SEFS — Severely Errored Framing Seconds, is a second with one or
more OOF errors or a detected incoming AIS.
SNA — Systems Network Architecture, data communication network
architecture developed by IBM in the 1970’s.
T1 — A Bell System term that refers to the physical carrier, or system of
transmission media and regenerators, used to transmit a digital signal at
1.544 Mbps.
T1.617-D — T1.617 Annex D, an ANSI link management protocol
specification used in Frame Relay.
TDM — Time Division Multiplexing, a technique in which separate data
or voice signals are transmitted simultaneously over a single
communications medium based on time interleaving.
Timeslot — A standard 64,000 bit/second channel. Synonymous with
DS0 (Digital Signal, level 0).
HSIM-W87 User’s Guide
C-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C: WAN Terms and Acronyms
UAS — Unavailable Seconds, the number of seconds that the DS3
interface is unavailable.
WAN — Wide Area Network, a network spanning a large geographic
area.
WPIM — WAN Physical Interface Module, Cabletron Systems modules
that provide connectivity/functionality for WAN modules such as the
BRIM-W6.
C-6
HSIM-W87 User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
|