6H258-17 and 6H259-17
SmartSwitch 6000 Interface Modules
Installation User’s Guide
9033381
Download from Www.Somanuals.com. All Manuals Search And Download.
Only qualified personnel should perform installation procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this document
without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes
have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR
RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.
Cabletron Systems, Inc.
35 Industrial Way
Rochester, NH 03866-5005
2000 by Cabletron Systems, Inc.
All Rights Reserved
Printed in the United States of America
Order Number: 9033381 January 2000
Cabletron Systems, QuickSET, SecureFast, and LANVIEW are registered trademarks and SmartSwitch is a
trademark of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of their respective
companies.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency
energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When
such trouble occurs, the user may be required to take corrective actions.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT:THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package.
The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU
ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO CABLETRON OR
YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1- 603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state
and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron makes
no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA
AND BY UNITED STATES OF AMERICA GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems Sales and Service, Inc.
(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in
the package. The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED
PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH
INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT
FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1-603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state
and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron
makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems Limited (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package.
The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU
ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO CABLETRON OR
YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1-603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be governed in accordance with English law. The English
courts shall have exclusive jurisdiction in the event of any disputes.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron
makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
THE GPIM-01 AND GPIM-09 GIGABIT ETHERNET MODULES
USE CLASS 1 LASER TRANSCEIVERS.
READ THE FOLLOWING SAFETY INFORMATION BEFORE INSTALLING OR OPERATING
THESE MODULES.
The Class 1 laser transceivers use an optical feedback loop to maintain Class 1 operation limits. This control loop
eliminates the need for maintenance checks or adjustments. The output is factory set, and does not allow any user
adjustment. Class 1 Laser transceivers comply with the following safety standards:
•
•
•
21 CFR 1040.10 and 1040.11 U.S. Department of Health and Human Services (FDA).
IEC Publication 825 (International Electrotechnical Commission).
CENELEC EN 60825 (European Committee for Electrotechnical Standardization).
When operating within their performance limitations, laser transceiver output meets the Class 1 accessible emission limit
of all three standards. Class 1 levels of laser radiation are not considered hazardous.
SAFETY INFORMATION
CLASS 1 LASER TRANSCEIVERS
LASER RADIATION AND CONNECTORS
When the connector is in place, all laser radiation remains within the fiber. The maximum amount of radiant power
-6
exiting the fiber (under normal conditions) is -12.6 dBm or 55 x 10 watts.
Removing the optical connector from the transceiver allows laser radiation to emit directly from the optical port. The
maximum radiance from the optical port (under worst case conditions) is
-2
3
2
0.8 W cm or 8 x 10 W m sr-1.
Do not use optical instruments to view the laser output. The use of optical instruments to view laser output
increases eye hazard. When viewing the output optical port, power must be removed from the network adapter.
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a Commercial
or Light Industrial Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this
notice conforms to the above directives.
Manufacturer
Legal Representative in Europe
Mr. Ronald Fotino
Mr. J. Solari
___________________________________
___________________________________
Full Name
Full Name
Compliance Engineering Manager
Managing Director - E.M.E.A.
___________________________________
___________________________________
Title
Title
Rochester, NH, USA
Newbury, Berkshire, England
___________________________________
___________________________________
Location
Location
x
Download from Www.Somanuals.com. All Manuals Search And Download.
ABOUT THIS GUIDE
Structure of This Guide .................................................................................................xvi
Related Manuals ..........................................................................................................xvii
1
Overview .........................................................................................................1-1
1.1.1 Connectivity........................................................................................1-3
1.1.4 SmartTrunk ........................................................................................1-4
1.1.6 Broadcast Suppression......................................................................1-4
1.1.8 Rate Limiting ......................................................................................1-5
1.1.10 Flow Control.......................................................................................1-6
1.1.11 802.1 Port Priority ..............................................................................1-6
1.1.12 Management ......................................................................................1-6
1.1.13 Switching Options ..............................................................................1-7
1.1.14 Distributed Chassis Management ......................................................1-7
1.1.15 Optional HSIMs and VHSIMs.............................................................1-7
1.1.16 Standards Compatibility .....................................................................1-7
1.1.17 LANVIEW Diagnostic LEDs ...............................................................1-8
1.1.18 Year 2000 Compliance.......................................................................1-8
Getting Help ....................................................................................................1-8
1.2
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
2
3
NETWORK REQUIREMENTS
100BASE-FX Network.....................................................................................2-1
2.1.1 Multimode Fiber Optic Cabling...........................................................2-1
SmartTrunk......................................................................................................2-2
3.1
3.3
Unpacking the SmartSwitch............................................................................3-1
Installing Options.............................................................................................3-2
Installing the SmartSwitch into the 6C105 Chassis.........................................3-2
Connecting to the Network..............................................................................3-4
Completing the Installation..............................................................................3-6
4
4.1
Using LANVIEW..............................................................................................4-1
Troubleshooting Checklist...............................................................................4-5
Using the RESET Button...............................................................................4-10
A
A.1
A.2
A.4
Module Specifications .....................................................................................A-1
Physical Properties .........................................................................................A-1
Input/Output Ports...........................................................................................A-2
B
B.1
Setting the Mode Switches..............................................................................B-1
SIMM Upgrade................................................................................................B-3
B.2.1 Locating SIMMs .................................................................................B-3
B.2.2 Installing the DRAM SIMM.................................................................B-4
Installing Optional High Speed Interface Modules ..........................................B-5
B.3
INDEX
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure
1-1
3-1
3-2
4-1
4-2
B-1
B-2
B-3
B-4
The SmartSwitch............................................................................................................. 1-2
Installing an Interface Module .........................................................................................3-3
Connecting a Fiber Optic Segment to the SmartSwitch..................................................3-5
LANVIEW LEDs ..............................................................................................................4-2
RESET Button...............................................................................................................4-10
Module Mode Switch Location/Component Layout.........................................................B-2
SIMM Slot Locations .......................................................................................................B-4
Installing the DRAM.........................................................................................................B-5
HSIM and VHSIM Connector Locations..........................................................................B-6
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table
3-1
4-1
4-2
4-3
4-4
4-5
4-6
A-1
Contents of SmartSwitch Shipping Container..............................................................3-1
LANVIEW LEDs...........................................................................................................4-3
Fault Identification........................................................................................................4-5
Power System Troubleshooting...................................................................................4-6
Firmware Troubleshooting ...........................................................................................4-7
Management System Troubleshooting ........................................................................4-8
Device Setup Troubleshooting.....................................................................................4-9
COM Port Pin Assignments......................................................................................... A-2
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Welcome to the Cabletron Systems 6H258-17 and 6H259-17 SmartSwitch 6000 Interface
Modules User’s Guide. This guide describes the 6H258-17 and 6H259-17 Interface Modules and
provides information concerning network requirements, installation and troubleshooting. For
information about how to use Local Management to configure and manage the SmartSwitch series,
refer to the SmartSwitch Series 6H202, 6H203, 6H252, 6H253, 6H258, 6H259, 6H262, 6E233,
and 6E253 Local Management User’s Guide.
Important Notice
Depending on the firmware version used in the 6H258-17 and 6H259-17, some features described
in this document may not be supported. Refer to the Release Notes shipped with the device to
determine which features are supported.
USING THIS GUIDE
Read through this guide completely to understand the 6H258-17 and 6H259-17 module features,
capabilities, and Local Management functions.
A general working knowledge of Fast Ethernet and IEEE 802.3 type data communications
networks and their physical layer components is helpful when using these devices.
This module has two versions, the multimode fiber version (6H258-17), and the single
mode fiber version (6H259-17). Since the only difference between the two versions is
NOTE
the type of fiber used in the network connection, the two versions will be referred to as
the SmartSwitch in the rest of this document. When information is specific to a version,
that version will be referred to by its name. The term “module” may also be used to refer
to either of the versions.
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
Structure of This Guide
STRUCTURE OF THIS GUIDE
This guide is organized as follows:
This About This Guide preface provides preliminary information that will aid in using this manual,
lists technology and user guides that may help the user set up and manage the SmartSwitch, and
Chapter 1, Introduction, describes the features of the SmartSwitch.
Chapter 2, Network Requirements, outlines the network requirements that must be met before
installing the SmartSwitch into the 6C105 SmartSwitch 6000 chassis.
Chapter 3, Installation, provides instructions on how to install the module in the chassis and
connect segments to the device.
Chapter 4, Troubleshooting, details the SmartSwitch LANVIEW LEDs that enable quick
diagnosis of network/operational problems.
Appendix A, Specifications, contains information on functionality and operating specifications,
connector pinouts, environmental requirements, and physical properties.
Appendix B, Switch Settings, Upgrades, and Installations, describes setting the Mode Switches,
and includes upgrade and installation information.
xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Related Manuals
RELATED MANUALS
The following manuals may help the user to setup and manage the SmartSwitch modules:
•
SmartSwitch Series 6H202, 6H203, 6H252, 6H253, 6H258, 6H259, 6H262, 6E233, and 6E253
Local Management User’s Guide
•
•
•
•
•
6C105 SmartSwitch 6000 Overview and Setup Guide
Ethernet Technology Guide
Cabling Guide
802.1Q VLAN User’s Guide
SmartTrunk User’s Guide
The following manuals, as applicable, may help the user to set up and manage the SmartSwitches:
•
•
•
•
•
•
•
•
•
•
•
HSIM-A6DP User’s Guide
HSIM-F6 User’s Guide
HSIM-FE6 User’s Guide
HSIM-W6 User’s Guide
HSIM-W84 User’s Guide
HSIM-W87 User’s Guide
HSIM-G01/G09 User’s Guide
VHSIM-G6 User’s Guide
VHSIM-A6DP User’s Guide
WAN Series Local Management User’s Guide
VHSIM-A6DP User’s Guide
The HSIM-W6 Installation Guide, the HSIM-W84 Installation Guide, and the WAN Series Local
Management User’s Guide are included on the QuickSET CD-ROM and, along with the other
manuals referenced above, can be obtained on the World Wide Web in Adobe Acrobat Portable
All documentation for Cabletron Systems SecureFast VLAN Manager software can be
found on the VLAN Manager CD-ROM.
NOTE
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Conventions
DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
Note symbol. Calls the reader’s attention to any item of information that may be of
special importance.
NOTE
Tip symbol. Conveys helpful hints concerning procedures or actions.
TIP
Caution symbol. Contains information essential to avoid damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action that could result in
personal injury or death due to an electrical hazard.
xviii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
This chapter introduces the 6H258-17 and 6H259-17 SmartSwitch 6000 interface modules and
provides information about how to obtain additional support from Cabletron Systems.
Important Notice
document may not be supported. Refer to the Release Notes shipped with the device to determine
which features are supported.
1.1 OVERVIEW
The SmartSwitch, shown in Figure 1-1, is a Fast Ethernet interface module for the Cabletron
Systems 6C105 chassis. The SmartSwitch has 16 MT-RJ fiber optic switched ports and 1 slot for
an optional High Speed Interface Module (HSIM) or Very High Speed Interface Module
(VHSIM). The 6H258-17 uses multimode fiber optic cable for the network connections, while the
6H259-17 uses single mode fiber optic cable. The physical connectors look the same.
The SmartSwitches can be used to connect individual high-bandwidth user devices, such as
workstations, or to provide a central switching point for multiple 100 Mbps Fast Ethernet
segments. The optional HSIMs provide one or more high speed uplinks to other networking
technologies such as Gigabit Ethernet, Fast Ethernet, Fiber Distributed Data Interface (FDDI),
Wide Area Network (WAN) and Asynchronous Transfer Mode (ATM). Some HSIMs also provide
additional Fast Ethernet ports in varying media types. The optional VHSIMs provide very high
speed uplinks to networking technologies such as ATM and Gigabit Ethernet.
The SmartSwitch ports can be configured to control frame traffic several ways, including
prioritizing traffic flow according to protocol type. The SmartSwitches can also be configured to
establish Virtual Local Area Networks (VLANs) and control the flow of frames associated with
each VLAN according to priority and Ether type. Detailed information about VLANs is provided
in the Local Management User’s Guide.
Introduction
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.1 Connectivity
The SmartSwitch modules connects to Fast Ethernet networks or workstations through the MT-RJ
fiber optic ports on the front panel for 100 Mbps with duplex capability. These ports are in full
compliance with the optical performance requirements of 100BASE-FX version of IEEE 802.3u.
The 6H258-17 ports support multimode fiber optic cables up to 2 km. The 6H259-17 ports support
single mode fiber optic cables up to 15 km.
SmartSwitches have a slot for an optional HSIM or VHSIM to provide additional connectivity to
various networking technologies.
1.1.2 Runtime IP Address Discovery
This feature enables the module to automatically accept an IP address from a Boot Strap Protocol
(BootP) server on the network into NVRAM without requiring a user to enter an IP address
through Local Management.
When the module is connected to the network and powered up, Runtime IP Address Discovery
(RAD) checks the module for an IP address. If one has not yet been assigned (module and 6C105
chassis IP address set to 0.0.0.0), RAD checks to see if any of the module interfaces have a link. If
so, RAD sends out Reverse Address Resolution Protocol (RARP) and BootP requests to obtain an
IP address from a RARP or BootP server on the network.
The RAD requests start at an interval of one per second. The interval then doubles after every
transmission until an interval of 300 seconds is reached. At this point, the interval remains at 300
seconds. The RAD requests continue until an IP address is received from a RARP or BootP server,
or an IP address is entered using Local Management.
The module will reboot after RAD is successful.
NOTE
1.1.3 Full Duplex Switched Ethernet
Each switched Fast Ethernet port on the SmartSwitch supports 100 Mbps operation and can be
configured to operate in Full Duplex Switched Ethernet (FDSE) mode. FDSE allows each port to
provide up to 200 Mbps of bandwidth.
Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.4 SmartTrunk
SmartTrunk, also referred to as SmartTrunking, is Cabletron Systems’ terminology for load
balancing or load sharing. SmartTrunk technology provides an easy-to-implement mechanism to
group, or aggregate, multiple links of any technology together to scale the backbone bandwidth
beyond the limitations of a single link. All links are user-configurable so administrators can scale
the backbone bandwidth by adding SmartTrunk links. The benefits of SmartTrunking include the
following:
•
•
•
All purchased bandwidth is used.
Distributed, resilient links increase reliability and performance.
Multiple technologies are supported within a single trunk for maximum flexibility.
For information on SmartTrunk configuration, refer to the Cabletron Systems
SmartTrunk User’s Guide.
NOTE
1.1.5 Remote Monitoring (RMON)
The SmartSwitch modules support all nine Ethernet RMON groups. The Statistics, Alarms, Events
and History groups are enabled on all ports by default.
Cabletron Systems RMON Actions is a vendor-specific extension of RMON and provides the
ability to set an “Action” on any SNMP MIB variable. The Action can be triggered by setting an
RMON Event and/or Alarm. An example of an Action would be to turn off a MIB-2 interface if a
broadcast threshold is crossed.
1.1.6 Broadcast Suppression
Broadcast Suppression enables a user to set a desired limit of receive broadcast frames per port/per
second to be forwarded out the other ports on the module up to the set limit. Any broadcast frames
above this specified limit are dropped. In the event that broadcast frames are being suppressed,
multicast and unicast frames continue to be switched.
1.1.7 Port/VLAN Redirect Functions
The port redirect function, also referred to as “Port Mirroring,” is a troubleshooting tool used to
map traffic from a single source port to a single destination port within the device. This feature
allows frames, including those with errors, to be copied and sent to an analyzer or RMON probe.
1-4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
The analyzer or RMON probe will see the data as if it were directly connected to the LAN segment
of the source port.
The VLAN redirect function is similar to the port redirect function except that the frames received
by the device are redirected to a designated destination port according to the VLAN classification
of the frames received. The VLAN redirect function does not support redirecting errors, and is
only supported when the device is operating as an 802.1Q switch. Multiple VLANs can be directed
to the same ports.
1.1.8 Rate Limiting
The Rate Limiting feature enables the SmartSwitch device to have control of traffic rates on a
per-port, per-priority basis. The network administrator can configure a rate limit (from 100 kbps to
1 Gbps) for a given port with an associated list of IEEE 802.1p priorities (which can include one,
some, or all of the eight priority levels defined in 802.1p). Each rate limit is specified as an
inbound or an outbound limit. The combined rate of all traffic on the port that matches the listed
priorities cannot exceed the programmed limit. If the rate exceeds the defined limit, frames are
dropped until the rate falls below the limit.
Administrators can configure up to four rate limit rules per port; however, each rule must not
include conflicting 802.1p priority values. In order to control traffic inbound and outbound on the
same port, two rate limit rules must be configured (one inbound and one outbound). Since the rate
limiting operation occurs after the processing of the multi-layer classification rules, the two
features can be combined to provide application-aware rate limiting.
This traffic rate function is not supported on ports configured as SmartTrunk ports.
NOTE
For more information about the application of the Rate Limiting function, refer to the Local
Management User’s Guide.
1.1.9 GARP Switch Operation
Some or all ports on the switch may be activated to operate under the Generic Attribute
Registration Protocol (GARP) applications, GARP VLAN Registration Protocol (GVRP) and/or
GARP Multicast Registration Protocol (GMRP).
GARP is a protocol, or set of rules, that outlines a mechanism for propagating the port state and/or
user information throughout a bridged LAN to keep track of users and VLANs on the network
fabric. MAC bridges and end users alike can take part in the registration and de-registration of
GARP attributes such as VLAN and multicast group membership. For more details on how GVRP
Introduction
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
and GMRP handle frames under GARP, and how to configure the switch ports to take advantage of
this operation, refer to Local Management User’s Guide.
1.1.10 Flow Control
Flow control is a method of managing the flow of frames between two devices. It ensures that a
transmitting device does not overwhelm a receiving device with data. This enables the receiving
device to communicate with the transmitting device, and to have it pause its transmission while the
receiving device processes the frames already received. Both devices must support the
IEEE 802.3x standard for flow control to work.
The SmartSwitch modules support the following two types of flow control:
•
•
frame based 802.3x
back pressure
Frame based 802.3x flow control is supported on all Ethernet ports operating in the full duplex
mode. Flow control can be enabled or disabled on a port-by-port basis.
Back pressure flow control is supported on all Ethernet ports operating in the standard mode of
operation. Flow control can be enabled or disabled on a port-by-port basis.
1.1.11 802.1 Port Priority
IEEE 802.1 port priority is incorporated in the IEEE 802.1D standard. It is used to assign a default
priority to the frames received without priority information in their tag header, to map prioritized
frames to the appropriate transmit queues, and to prioritize frames according to protocol type.
1.1.12 Management
Management of the SmartSwitch modules and 6C105 chassis is accomplished using the Local
Management application or remote SNMP management stations. Local Management is accessible
through the RS232 COM port on the front panel using a local VT100 terminal, or a remote VT100
terminal via a modem connection, and in-band via a Telnet connection. In-band remote
Local Management, as described in your Local Management User’s Guide, provides the ability to
manage the SmartSwitches and offers information for Ethernet HSIMs or VHSIMs. Local
Management information for non-Ethernet HSIMs or VHSIMs is included in their respective
user’s guide. For details on how to get manuals, refer to the Related Manuals section in the About
This Guide section.
1-6
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.13 Switching Options
SmartSwitches provide 802.1Q switching or SecureFast Switching Virtual Network Services
between all of the front panel interfaces including any optional HSIM or VHSIM. In the 802.1Q
mode (the default mode of operation), the switch functions as an 802.1D switch until VLANs are
configured.
SecureFast switching and IEEE 802.1Q switching allow migration to Virtual Network
technologies without requiring the replacement of existing equipment.
1.1.14 Distributed Chassis Management
From a management perspective, the 6C105 SmartSwitch 6000 chassis can be viewed as a single
entity with a single IP address. Its systems management functions are distributed to all modules.
The chassis can be managed using a single IP address, or the modules can be managed separately
by individual IP addresses. When using a single IP address, system wide settings can be done from
the chassis menu in Local Management, while module settings are done by selecting the specific
module to be modified and changing the settings for that module.
1.1.15 Optional HSIMs and VHSIMs
The SmartSwitches provide a slot for an optional High Speed Interface Module (HSIM) or Very
High Speed Interface Module (VHSIM) for additional connectivity to various networking
technologies. Any exceptions to the HSIMs and VHSIMs that operate in the SmartSwitch modules
are listed in the Release Notes shipped with the SmartSwitch.
1.1.16 Standards Compatibility
The SmartSwitch modules are fully compliant with the IEEE 802.3, 802.3x, 802.3u, 802.1D, and
specifically 802.1Q standards. SmartSwitches provide IEEE 802.1D Spanning Tree Algorithm
(STA) support to enhance the overall reliability of the network and protect against “loop”
conditions.
SmartSwitches support a wide variety of industry standard MIBs including RFC 1213 (MIB II),
RFC 1757 (RMON), RFC 1493 (Bridge MIB), RFC 1354 (FIB MIB), and RFC 1190 (Path MTU
Discovery). A full suite of Cabletron Systems Enterprise MIBs provide a wide array of statistical
information to enhance troubleshooting.
For information about how to extract and compile individual MIBs, contact Cabletron Systems.
Introduction
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Help
1.1.17 LANVIEW Diagnostic LEDs
LANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way
to observe the status of individual ports and overall network operations.
1.1.18 Year 2000 Compliance
The SmartSwitch modules and 6C105 chassis have an internal clock that can maintain the time and
date beyond the year 1999.
1.2 GETTING HELP
For additional support related to this device or document, contact Cabletron Systems using one of
the following methods:
World Wide Web
Phone
(603) 332-9400
Internet mail
FTP
anonymous
Login
Password
your email address
To send comments or suggestions concerning this document, contact the Cabletron Systems Technical
Make sure to include the document Part Number in the email message.
Before calling Cabletron Systems, have the following information ready:
•
•
•
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem (e.g., changing mode
switches, rebooting the unit, etc.)
•
•
•
•
•
The serial and revision numbers of all involved Cabletron Systems products in the network
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a recurring problem, etc.)
Any previous Return Material Authorization (RMA) numbers
1-8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Network Requirements
Before installing the SmartSwitch modules, review the requirements and specifications referred to
in this chapter concerning the following:
•
•
100BASE-FX Network (Section 2.1)
SmartTrunk (Section 2.2)
The network installation must meet the guidelines in this chapter and in the documents referenced
in this chapter to ensure satisfactory performance of the equipment. Failure to follow the
guidelines may produce poor network performance.
2.1 100BASE-FX NETWORK
network meets the optical performance requirements for 100BASE-FX IEEE 802.3u standard.
One module, the 6H258-17, is made specifically for multimode fiber optic cable and the other, the
6H259-17, is made specifically for single mode fiber optic cable. The two modules cannot be used
interchangeably with respect to multimode or single mode fiber optic cable. Refer to Section 2.1.1
for information on multimode cabling, and Section 2.1.2 for information on single mode cabling
for these modules.
2.1.1 Multimode Fiber Optic Cabling
The 6H258-17 fixed ports use LEDs to support multimode fiber optic cables at the 1300 nm
wavelength, at lengths of up to 2 km.
Refer to the Cabletron Systems Cabling Guide for more details on multimode fiber optic
connections for the 6H258-17.
Network Requirements
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartTrunk
2.1.2 Single Mode Fiber Optic Cabling
The single mode fiber optic module, the 6H259-17, operates at a nominal wavelength of 1300 nm.
The 6H259-17 fixed ports use a Class 1 laser to support single mode 9/125 micron fiber optic
cables at lengths of up to 15 km.
2.2 SmartTrunk
To connect the SmartSwitch modules to a network to take advantage of the SmartTrunk feature,
there are certain rules concerning port connections and configurations that must be followed for
proper operation. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional
information.
NOTE
The Cabletron Systems Cabling Guide and the SmartTrunk User’s Guide can be found
2-2
Network Requirements
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installation
Only qualified personnel should install the SmartSwitch.
supported features and operation documented in this guide.
NOTE
This chapter covers the following items:
•
•
•
•
•
Installing Options (Section 3.2)
Installing the SmartSwitch into the 6C105 Chassis (Section 3.3)
Connecting to the Network (Section 3.4)
Completing the Installation (Section 3.5)
3.1 UNPACKING THE SMARTSWITCH
1. Open the box and remove the packing material protecting the module.
2. Verify the contents of the carton as listed in Table 3-1.
Table 3-1 Contents of SmartSwitch Shipping Container
Item
Quantity
SmartSwitch
1
1
Manual Accessory Kit
Installation
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Options
3.2 INSTALLING OPTIONS
If installing an optional HSIM or VHSIM, it must be installed in the SmartSwitch before
proceeding to Section 3.3. Complete instructions for installing an optional HSIM or VHSIM are
available in the applicable HSIM or VHSIM User’s Guide. For details on how to get manuals, refer
to the Related Manuals in the About This Guide preface. Refer to Appendix B for the HSIM or
VHSIM connector locations.
3.3 INSTALLING THE SMARTSWITCH INTO THE 6C105 CHASSIS
Failure to observe static safety precautions could cause damage to the SmartSwitch.
Follow static safety handling rules and wear the antistatic wrist strap provided with the
6C105 chassis.
!
CAUTION
Do not cut the non-conductive bag to remove the module. Damage could result from
sharp objects contacting the board or components.
The SmartSwitch modules can be installed in any of the 5 slots that are available. To install a
module, refer to Figure 3-1 and proceed as follows:
1. Remove the blank panel covering the slot in which the module will be installed. All other slots
must remain covered to ensure proper airflow and cooling. (Save the blank plate in the event
you need to remove the module.)
2. Carefully remove the module from the shipping box. (Save the box and packing materials in the
event the module must be reshipped.)
3. Locate the antistatic wrist strap shipped with the 6C105 chassis. Attach the antistatic wrist strap
to your wrist and plug the cable from the antistatic wrist strap into the ESD grounding
receptacle at the upper right corner of the 6C105.
4. Remove the module from the plastic bag. (Save the bag in the event the module must be
reshipped.) Observe all precautions to prevent damage from Electrostatic Discharge (ESD).
3-2
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the SmartSwitch into the 6C105 Chassis
Slot Number
Plastic Locking Tab
Backplane
Connector
3
4
5
PS1
PS2
1
2
Fast Enet
6H253-17
RESET
RX
TX
C
O
M
1
2
RX
TX
CPU
RX
TX
3
RX
TX
4
RX
TX
5
RX
TX
6
RX
TX
7
RX
TX
8
RX
TX
9
RX
TX
10
11
12
13
14
15
16
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
2159-01
Metal Back-Panel
Circuit Card
Card Guides
Plastic
Locking Tab
Figure 3-1 Installing an Interface Module
5. Examine the module for damage. If any damage exists, DO NOT install the module.
Immediately contact Cabletron Systems. Refer to Section 1.2.
Installation
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Network
To prevent damaging the backplane connectors in the following step, take care that the
module slides in straight and properly engages the backplane connectors.
!
CAUTION
the front panel of the chassis. Refer to Figure 3-1.
6. Locate the slot guides that line up with the number of the slot in which the module will be
installed. Install the module in the chassis by aligning the module circuit card between the upper
top and bottom plastic locking tabs, as shown in Figure 3-1. Take care that the module slides in
straight and properly engages the backplane connectors.
7. If the chassis in which the module is installed was powered down for the installation, turn it
back on. Check to see that the CPU LED settles at solid green after a few minutes. If the LED
does not turn solid green, see Chapter 4 for details.
3.4 CONNECTING TO THE NETWORK
This section provides the procedures for connecting segments from the network or other devices to
the SmartSwitch.
If the SmartSwitch is being installed in a network using SmartTrunking, there are rules
NOTE
SmartTrunking to operate properly. Before connecting the cables, refer to the Cabletron
Systems SmartTrunk User’s Guide for the configuration information.
For the 6H258-17 and multimode fiber optic cable configuration information, refer to the
Cabletron Systems Cabling Guide.
See Section 2.1 for information on connecting using single mode fiber optic cable with
the 6H259-17.
3-4
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Network
.
Fast Enet
6H258-17
Receive
RESET
(RX) LED
RX
TX
1
2
3
4
5
6
C
O
M
Transmit
(TX) LED
RX
TX
CPU
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
7
8
9
MT-RJ Port
RX
TX
RX
TX
RX
TX
10
11
Fiber Optic Cable
RX
TX
RX
TX
12
Release Tab
RX
TX
13
14
15
RX
TX
RX
TX
Figure 3-2 Connecting a Fiber Optic Segment to the SmartSwitch
Connect a fiber optic segment to the SmartSwitch as follows:
1. Remove protective covers from the fiber optic segment or MT-RJ port.
connected to protect the connectors from dust and dirt. If a segment is removed from
NOTE
the SmartSwitch, the protective covers should be replaced until the segment is
re-installed.
2. Connect the fiber optic segment to the SmartSwitch by inserting the MT-RJ connector into the
desired port until the release tab catches, as shown in Figure 3-2.
Installation
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Completing the Installation
3. Verify that a link exists by checking that the port RX (Receive) LED is ON (flashing amber,
blinking green, or solid green). If the RX LED is OFF and the TX (Transmit) LED is not
blinking amber, perform the following steps:
a. Verify that the device at the other end of the fiber optic segment is powered on and properly
connected to the segment.
b. Ensure that the fiber optic connection meets the dB loss and cable specifications outlined
in the Cabletron Systems Cabling Guide. Refer to the Related Manuals in the About This
Guide preface for information on obtaining this document.
4. If a link is not established, refer to Chapter 4 before contacting Cabletron Systems. Refer to
Section 1.1 for details.
5. Repeat steps 1 through 3 above, until all connections have been made.
3.5 COMPLETING THE INSTALLATION
After installing the SmartSwitch and any optional HSIM or VHSIM, the module is now ready to be
set up through Local Management. For information on the Local Management connection,
configuring the 6C105 chassis and module, and using Network Tools, refer to the Local
Management User’s Guide.
3-6
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Troubleshooting
This chapter provides information concerning the following:
•
•
•
Using the LANVIEW diagnostic and status monitoring system (Section 4.1)
Troubleshooting network and module operational problems (Section 4.2)
Using the RESET button (Section 4.3)
4.1 USING LANVIEW
The SmartSwitch modules use Cabletron Systems’ built-in visual diagnostic and status monitoring
system called LANVIEW. The LANVIEW LEDs (Figure 4-1) allow quick observation of the
network status to aid in diagnosing network problems. Refer to Table 4-1 for a description of the
LEDs.
Refer to the HSIM or VHSIM User’s Guide for a description of the HSIM or VHSIM LEDs.
The terms flashing, blinking, and solid used in the LED definition tables of this
chapter indicate the following:
NOTE
Flashing indicates an irregular LED pulse.
Blinking indicates a steady LED pulse, (approximately 50% on, 50% off).
Solid indicates a steady LED light. No pulsing.
Troubleshooting
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using LANVIEW
Table 4-1 LANVIEW LEDs
LED
Color
State
Power off.
Recommended Action
CPU
Off
Power up chassis.
Red
Blinking. Hardware failure Contact Cabletron Systems.
has occurred.
Solid. Resetting, normal
power up reset.
If the LED remains red for several
minutes, contact Cabletron Systems.
Amber
Blinking. Crippled.
Solid. Testing.
Contact Cabletron Systems.
If the LED remains amber for several
minutes, contact Cabletron Systems.
Green
Solid. Functional.
None.
Amber
Booting. Blinks amber and None.
and Green green while booting.
RX
Off
No link. No activity or port None.
in Standby. Port enabled or
disabled.
Green
Solid. Port enabled, link, no None.
activity.
Blinking. Port disabled,
Enable port if desired.
link.
Amber
Red
Flashing. Port enabled,
link, activity.
None.
Diagnostic failure.
Contact Cabletron Systems.
Troubleshooting
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using LANVIEW
Table 4-1 LANVIEW LEDs (Continued)
State Recommended Action
LED
Color
TX
Off
Port enabled, and no
activity. Should flash green
every two seconds
1. Ensure that the STA is enabled and
that there is valid link. describes how
to enable the STA.
indicating BPDUs being
sent if STA is enabled and
there is a valid link.
2. Contact Cabletron Systems.
Green
Flashing. Indicates activity. None.
Rate indicates data rate.
Amber
Blinking. Port in standby.
1. Ensure that the port is not disabled.
Refer to your Local Management
User’s Guide for information on
enabling/disabling ports.
Port may be disabled due to
Spanning Tree.
2. Contact Cabletron Systems.
Red
Flashing. Indicates
collision rate.
None, unless there is a high rate of
activity. If so, check for network
configuration problems or a defective
device.
Solid. Diagnostic Failure.
Contact Cabletron Systems.
4-4
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
4.2 TROUBLESHOOTING CHECKLIST
If the SmartSwitch is not working properly, refer to Table 4-2 for a checklist of possible problems,
causes, and recommended actions to resolve the problem.
Table 4-2 Fault Identification
Symptom
Possible Causes
All LEDs off.
1. Installation error - Remove the SmartSwitch and perform
installation in accordance with installation instructions. Check
connectors for dust or dirt and clean as necessary.
2. Power system fault - refer to Table 4-3.
state.
sending out BootP requests in an effort to locate a BootP server
on the network. Press the RESET button on the front panel to
attempt to use the firmware image in FLASH memory.
download.
3. Contact Cabletron Systems if the problem continues.
1. Firmware image fault - refer to Table 4-4.
Cannot access Local
Management.
2. Management system fault - refer to Table 4-5.
Cannot contact device
through in-band
management.
2. No link to device - verify all network connections between the
network management station and the SmartSwitch are valid and
operating.
User parameters
(IP address,
Device setup fault - refer to Table 4-6.
community names,
etc.) lost on reset or
power-up.
Device is not
Device setup fault - refer to Table 4-6.
forwarding traffic from
any port.
Troubleshooting
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-3 Power System Troubleshooting
Instruction
Possible Causes
Loss of Power to the
6C105 chassis.
Perform the following steps:
1. Check ON/OFF switches of 6C105 power supplies. All switches
must be in the ON ( | ) position.
2. Check all power cords and cables for proper connection. Examine
power cords for fraying or other damage. Replace if necessary.
3. Examine 6C105 chassis power supplies. If power supply LEDs or
audible warning tone indicate power supply problems,
troubleshoot or replace any faulty power supplies.
Fault in 6C105 power 1. Remove the SmartSwitch from the current slot and re-install in
bus.
another free slot in the chassis.
2. If the SmartSwitch functions in the selected slot, the SmartSwitch
onboard power converter is operational. The 6C105 chassis power
bus may have a localized fault. Install the SmartSwitch in the
working slot and contact Cabletron Systems.
3. If the SmartSwitch does not function in the selected slot, continue
the process with all module slots in the chassis. If the module
does not function in any slot, the chassis power bus may have a
system-wide fault or the module onboard power converter may be
inoperable. Diagnose the module power converter as described
below to isolate the fault.
Fault in SmartSwitch
module power
converter.
1. Remove a working module from a known good chassis.
2. Install the SmartSwitch in the known good slot.
3. If the SmartSwitch does not function, there may be a fault in the
onboard power converter. Contact Cabletron Systems
immediately.
4-6
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-4 Firmware Troubleshooting
Instruction
Possible Causes
Autobaud enabled.
Press ENTER (RETURN) (may take up to four times).
Terminal setup is not correct. Refer to your Local Management User’s Guide for proper
setup procedures.
Improper console cable
pinouts.
Refer to Appendix A for proper console port pinouts.
The COM port of the device 1. Establish a Telnet connection to the device.
has been disabled, or the
2. Refer to your Local Management User’s Guide for
COM port application has
instructions on enabling/disabling the COM port and
been changed.
changing the COM port application.
Corrupt firmware image, or
hardware fault.
1. If possible, attempt to download the image to the device
again. Refer to Section B.1 for instructions on how to force
a download of a new firmware image.
2. Contact Cabletron Systems if the problem continues.
Troubleshooting
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-5 Management System Troubleshooting
Possible Causes
Instruction
Improper Community
Names Table.
1. Refer to your Local Management User’s Guide for
Community Names Table setup.
2. If the Community Names have been forgotten, refer to
Section B.1 for instructions on clearing NVRAM.
The SmartSwitch does not
have an IP address.
1. Refer to your Local Management User’s Guide for IP
address assignment procedure.
2. If the SmartSwitch are using the IP address of the 6C105
chassis, ensure that the modules are not in STANDALONE
management mode. Your Local Management User’s Guide
provides instructions on setting the management mode.
The applicable front panel
port is disabled.
1. Enable port. Refer to the Local Management User’s Guide
for instructions on enabling/disabling ports.
2. Port may disabled due to Spanning Tree. Review network
design and delete unnecessary loops.
4-8
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-6 Device Setup Troubleshooting
Instruction
Possible Causes
The SmartSwitch detect a
looped condition.
1. Verify that Spanning Tree is enabled. Refer to the Local
Management User’s Guide for instructions on setting the
type of STA.
2. Review network design and delete unnecessary loops.
Mode switch (7),
1. Reenter the lost parameters as necessary. Refer to the Local
Management User’s Guide for instructions on configuring
the device through Local Management.
NVRAM Reset, was
changed sometime before
either cycling power or
pressing the RESET
button, causing the
user-entered parameters to
reset to factory default
settings.
2. Call Cabletron Systems if the problem continues.
Clear NVRAM was set
through Local
Management.
1. Reenter the lost parameters as necessary. Refer to the Local
Management User’s Guide for instructions on configuring
the device through Local Management.
2. Call Cabletron Systems if the problem continues.
If these troubleshooting tables do not solve any problems that occur with the
SmartSwitch, contact Cabletron Systems. Refer to Section 1.2 for details.
NOTE
Troubleshooting
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RESET Button
4.3 USING THE RESET BUTTON
The RESET button located near the upper plastic locking tab of the module (refer to Figure 4-2)
resets the SmartSwitch processor without affecting the NVRAM.
Pressing the RESET button resets the device, and all current switching being
performed by the module is halted. A module downtime of up to two minutes
results from this action.
!
CAUTION
FAST ENET
6H258-17
RESET Button
RESET
reset
Figure 4-2 RESET Button
To reset the SmartSwitch processor, press and release the RESET button. To push the button, use a
pen or similar tool, as the button is recessed behind the metal plate of the front panel. The module
processor goes through a reset process of approximately 60 seconds. Additional downtime may be
added as the module reenters the network.
It is not recommended to press the reset button while the module is already in
reset mode. The module will enter an extended diagnostic procedure, which is
NOTE
unnecessary for normal operation. This procedure will take much longer than a
minute. The ESC key can be used to exit the procedure.
4-10
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
This appendix provides operating specifications for the Cabletron Systems 6H258-17 and
6H259-17 Interface Modules. Cabletron Systems reserves the right to change these specifications
at any time without notice.
A.1 MODULE SPECIFICATIONS
Processor:
Intel i960 RISC processor control Power PC
Dynamic Random Access Memory (DRAM): 20 MB
FLASH Memory:
Shared Memory:
8 MB
4 MB
A.2 PHYSICAL PROPERTIES
Dimensions:
46.43 H x 6.05 W x 29.51 D (cm)
18.28 H x 2.38 W x 11.62 D (in)
Weight (Unit):
2.72 kg (6 lb)
200,000 hours
MTBF (Predicted):
Specifications
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Environmental Requirements
A.3 ENVIRONMENTAL REQUIREMENTS
Operating Temperature:
Storage Temperature:
5°C to 40°C (41°F to 104°F)
-30°C to 73°C (-22°F to 164°F)
5% to 90% (non-condensing)
Operating Relative Humidity:
A.4 INPUT/OUTPUT PORTS
Ports 1 through 16: Fast Ethernet 100 Mbps
(100BASE-FX compliant) with MT-RJ connectors:
6H258-17 using multimode fiber only
6H259-17 using single mode fiber only
Slot for optional High Speed Interface Module (HSIM)
or Very High Speed Interface Module (VHSIM):
Slot accepts optional HSIMs or VHSIMs
that provide a variety of connections
A.5 COM PORT PINOUT ASSIGNMENTS
The COM port is a serial communications port that supports Local Management or connection to a
UPS. Table A-1 shows the COM port pin assignments:
Table A-1 COM Port Pin Assignments
Pin
Signal Name
Input/Output
1
2
3
4
5
6
7
8
Transmit Data (XMT)
Data Carrier Detect (DCD)
Data Set Ready (DSR)
Receive Data (RCV)
Output
Output
Input
Input
NA
Signal Ground (GND)
Data Terminal Ready (DTR)
Request to Send (RTS)
Clear to Send (CTS)
Output
Input
NA
A-2
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance
A.6 REGULATORY COMPLIANCE
Safety:
UL 1950, CSA C22.2 No. 950, EN 60950, IEC 950,
and 73/23/EEC
Electromagnetic Compatibility (EMC):
FCC Part 15, EN 50082-1, EN 55022, VCCI V-3,
CSA C108.8, 89/336/EEC, and AS/NZS 3548
6H258-17 Specifications (Ports 1 through 16):
Fast Ethernet 100 Mbps (100BASE-FX compliant) with MT-RJ connectors using multimode fiber.
6H259-17 Specifications (Ports 1 through 16):
Fast Ethernet 100 Mbps (100BASE-FX compliant) with MT-RJ connectors using single mode
fiber.
Options for both the 6H258-17 and the 6H259-17:
Slot for optional High Speed Interface Module (HSIM) or Very High Speed Interface Module
(VHSIM). Slot accepts optional HSIMs or VHSIMs that provide a variety of connections.
Specifications
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Switch Settings, Upgrades, and Installations
This appendix covers the following items:
•
•
•
Setting the mode switches (Section B.1)
Installing the DRAM SIMM (Section B.2)
Location for installing HSIMs or VHSIMs (Section B.3)
An antistatic wrist strap (provided with 6C105 chassis) is required to perform the
procedures in this appendix. Use the antistatic wrist strap when performing any of the
procedures in this appendix to minimize ESD damage to the devices involved.
!
CAUTION
B.1 SETTING THE MODE SWITCHES
Read the appropriate sections to be fully aware of the consequences when changing
switch settings.
!
CAUTION
Only qualified personnel should change switch settings.
These switches are set at the factory and do not need to be changed unless you intend to perform
the following:
•
•
Force download a new image file from a BootP server.
Clear NVRAM and restore all user-entered parameters such as the IP address and Subnet Masks
to the SmartSwitch “Default” configuration settings.
•
Clear user-entered passwords stored in NVRAM and restore the default passwords.
Switch Settings, Upgrades, and Installations
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Mode Switches
Figure B-1 shows the location of the mode switches and the switch settings for normal operation.
DRAM
MODE SWITCH
OFF ON
1
2
3
4
5
6
7
8
2159_34
Figure B-1 Module Mode Switch Location/Component Layout
Switch definitions and positions are as follows:
•
•
Switches 1 through 4 – For Cabletron Systems use only.
Switch 5 – COM Port Autobaud. The default (OFF) position enables Autobaud sensing on the
COM port for Local Management sessions. Changing the switch to the ON position disables
Autobaud sensing and sets the COM port to 9600 baud for Local Management sessions.
•
Switch 6 – Forced BootP. Changing the position of this switch (i.e., moving the switch from one
position to the other) clears download information from NVRAM and forces the SmartSwitch
to download a new image file from a BootP server after power to the chassis is restored.
After changing the position of switch 6, DO NOT reapply power to the chassis until there
is a station acting as a BootP server, which contains the image file.
NOTE
B-2
Switch Settings, Upgrades, and Installations
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMM Upgrade
•
After changing the position of switch 6 and restarting the module, the SmartSwitch requests a
new image download until they either receive a new image or the RESET button on the front
panel is pressed. When the RESET button is pressed, the SmartSwitch continues trying to
contact a BootP server, but will time out in approximately one minute. If the module times out,
the image is downloaded from its FLASH memory.
•
•
Switch 7 – Clear NVRAM. Changing the position of this switch resets NVRAM on the next
power up. ALL user entered parameters, such as IP addresses, subnet masks, SNMP traps, and
switching functions are restored to their factory default settings.
Switch 8 – Reset Password/Community Strings. Changing the position of this switch clears
only the user-entered passwords stored in NVRAM, and restores the default passwords. Once
the SmartSwitch reset, the passwords can either be reentered or the default passwords (Public
and ENTER) may be used.
Do not change the position of switch 8 unless it is necessary to reset the module
super-user configured passwords to their factory default settings.
NOTE
B.2 SIMM UPGRADE
Memory upgrade is available for the SmartSwitch modules to expand the DRAM to 32 MB. This
section explains how to locate and add/replace a Single In-line Memory Module (SIMM). For
help, refer to Section 1.2.
B.2.1 Locating SIMMs
Figure B-2 shows the location of the DRAM SIMM connector.
Switch Settings, Upgrades, and Installations
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMM Upgrade
DRAM SIMM
Figure B-2 SIMM Slot Locations
B.2.2 Installing the DRAM SIMM
Observe all antistatic precautions when handling sensitive electronic equipment.
!
CAUTION
To install a DRAM SIMM, refer to Figure B-3 and proceed as follows:
1. With the SIMM alignment notch oriented as shown in Figure B-3, insert the SIMM down
between the connector teeth.
2. Pivot the SIMM downward so the connector clips align with the two side notches of the SIMM
and the connector clips lock the SIMM into place.
B-4
Switch Settings, Upgrades, and Installations
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Optional High Speed Interface Modules
Connector
Connector
Teeth
Clip
Side Notch
1
Clip
Alignment Notch
2
SIMM
Side Notch
2504-91
Figure B-3 Installing the DRAM
B.3 INSTALLING OPTIONAL HIGH SPEED INTERFACE MODULES
Figure B-4 shows the location of the two connectors for an optional High HSIM or VHSIM.
Depending on if an HSIM or VHSIM is installed, one or both connectors are used.
Refer to the installation instructions for the optional HSIM or VHSIM in the associated
user’s guide.
NOTE
Switch Settings, Upgrades, and Installations
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Module 3-1
Numerics
100BASE-FX
connection 3-4
requirements 2-1
installation B-5
Local Management
introduction 1-6
C
Cable Specifications
100BASE-FX network 2-1
COM port
pin assignments A-2
Connecting to the network 3-4
Memory upgrading B-3
Mode Switch Bank Settings B-1
D
Distributed Chassis Management 1-7
Document Conventions xviii
N
NVRAM
clearing B-3
E
Environmental requirements A-2
P
Physical properties A-1
H
Help 1-8
related manuals xvii
Redirect functions
I
port and VLAN, introduction to 1-4
Regulatory Compliance A-3
Related Manuals xvii
Installation
connecting to the Network 3-4
High Speed Interface Module B-5
RESET button 4-10
Runtime IP Address Discovery 1-3
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
S
Safety A-2
Safety information
laser ix
Troubleshooting 4-1
checklist 4-5
SDRAM
installation B-5
SIMMs
U
installing
LDRAM B-4
location B-3
SmartTrunk
V
VLAN Redirect Function, introduction to 1-4
introduction to 1-4
Specifications A-1
Standards compatibility 1-7
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|