The Bose® Wave® Radio
Owner’s Guide
January 4, 2002
AM189930_01_V.pdf
FPO
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
For your safety
1. Read, Follow, And Save All Instructions – Read and follow the complete safety and operating
instructions in this owner’s guide before using the unit. Save this guide for future reference.
2. Pay Attention To Warnings – Observe all warnings on the unit and in the guide.
3. Do Not Let Objects Or Liquid Enter The Unit – Take care to prevent objects or liquids
from entering this unit. Do not use near a bathtub, washbowl, kitchen sink, laundry tub, in
a wet basement, near a swimming pool, or anywhere else that water is present. Clean only
as directed on page 18.
4. Maintain Proper Ventilation – Place the unit so nothing interferes with its proper ventilation.
Do not place on a bed, sofa, or similar surface that mayblocktheventilation openings. Do not put
it in a bookcase or cabinet that may keep air from flowing through its ventilation openings.
5. Avoid Excessive Heat – Do not place the unit near heat sources such as radiators, stoves,
or other appliances (including amplifiers) that produce heat.
6. Use Proper Power Sources – Plug the unit into a proper power supply, as described in the
operating instructions or as marked on the unit. This unit has a polarized alternating current
line plug (one blade is wider than the other). As a safety feature, the plug fits into the power
outlet only one way. If you have trouble inserting it, reverse the plug. If it still does not fit,
your outlet may be obsolete and needs to be replaced. Contact an electrician. Do not
change the plug to defeat this safety feature.
7. Protect The Power Cord – Route all power cords so that they are not likely to be walked on
or pinched. Pay particular attention to cords at plugs, at the point where the cord connects
to the unit, and at outlets on the unit.
8. Take Precautions When Unit Is Not In Use – If the unit will not be used for an extended
period, unplug from the outlet and remove the batteries.
9. Be Careful With Carts And Stands – Do not place this unit on an unstable cart, stand,
tripod, bracket, or table. The unit may fall, causing serious injury to a person or damage to
the unit. For advice on use of a particular cart, stand, tripod, bracket, or table, contact
Bose® Corporation. Be careful when moving the unit and cart combination. Quick stops,
excessive force, and uneven surfaces may cause it to overturn.
10. Avoid Power Lines – Do not install external antennas near overhead power lines or other
electric light or power circuits, nor where an antenna can fall into such circuits or power lines.
Antenna
Lead In Wire
11. Ground All Outdoor Antennas – If an external antenna or cable system is connected to this
unit, be sure the antenna or cable system is grounded. This will provide some protection
against voltage surges and built-up static charges.
Ground
Clamp
Antenna
Discharge Unit
(NEC Section 810-20)
Section 810 of the National Electrical Code ANSI/NFPA No. 70 provides information with
respect to proper grounding of the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of the grounding conductors, location of antenna-
discharge unit, connection to grounding electrodes, and requirements for the ground
electrode. Refer to the antenna grounding illustration.
Grounding
Conductors
(NEC Section 810-21)
Electric
Service
Equipment
Ground Clamps
Power Service Grounding
Electrode System
(NEC ART 250 Part H)
Note to CATV system installer:
This reminder calls the CATV system
installer’s attention to Article 820-40 of
the NEC (of USA) that provides
12. Obtain Authorized Service When It Is Indicated – Do not attempt to service this unit
yourself. All servicing should be provided by authorized service personnel when:
A. The power supply cord or the plug has been damaged, or
guidelines for proper grounding. It
specifies that the cable ground shall be
connected to the grounding system of
the building, as close to the point of
cable entry as is practical.
B. Objects have fallen or liquid has spilled into the unit, or
C. The unit has been exposed to rain, or
D. The unit does not appear to operate normally or exhibits a marked change in performance, or
E. The unit has been dropped or the cabinet damaged.
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
3
Contents
Please read this owner’s guide
The Bose® Wave® radio is carefully engineered to provide sound quality far beyond other
radios. This guide will help you set up and operate your radio properly.
Where to find...
Safety Instructions
Cautions ................................................................................................................. 3
For your safety ....................................................................................................... 3
Setting Up
Unpack the carton.................................................................................................. 5
Install the batteries ................................................................................................. 5
Connect the power cord ........................................................................................ 6
The remote control ................................................................................................. 7
The Display
How to read the clock display ............................................................................... 8
How to read the radio display ................................................................................ 8
How to customize the display................................................................................ 9
Functions
Radio functions .................................................................................................... 10
Clock functions .................................................................................................... 12
Other Components
Connecting other components ............................................................................ 16
Using other components...................................................................................... 17
Product Information
Maintaining the Wave radio ................................................................................. 18
For best radio reception....................................................................................... 18
Features................................................................................................................ 18
Bose® Corporation
Warranty ............................................................................................................... 19
Customer service ................................................................................................. 19
4
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Setting Up
Unpack the carton
Carefully unpack the carton. Do not attempt to use the Wave® radio if any part appears
damaged. Instead, repack the carton and notify Bose® or your authorized Bose dealer immedi-
ately.
It is best to place the radio across the room from where you will be listening. Place the radio on
a table or other flat surface. Do not put it on a metal surface or table that could interfere with
AM reception. If you will use the radio with your television or VCR, do not place it on top of the
television. It may interfere with the picture quality.
Locate the power cord, AA batteries, remote control, and lithium battery.
Figure 1
What comes with your radio.
• Wave radio
• Power cord
• Remote control
• Lithium battery
• AA batteries
Wave
radio
3 AA batteries
®
SLEEP
TIME ALARM
.
STA
ING
TUN
3
2
1
PRESET STATIONS
5
6
4
MUTE
VOLUME
Remote control
AM
FM
ON/OFF
AUX
RC-1
NTROL AW
R
EMOTE CO
CEIVER
WAVE RE
ACOUSTIC
Power cord
Lithium
battery
Install the batteries
The Wave radio’s three AA batteries maintain the memory and backup alarm system for up to a
week during a power failure, or while the radio is unplugged. Operating without batteries leaves
the memory unprotected, but will not harm the radio. Use AA batteries (IEC-R6 in Europe),
available at many retail stores.
Note: The batteries will not power the radio or
light the display.
Figure 2
Installing the batteries.
+ – +
1. Carefully turn your radio upside down (avoid
scratching its top).
2. Locate the battery compartment on the
bottom (see Figure 2).
3. Press the arrow on the cover to slide the
compartment open.
4. Place the batteries inside, matching the +
and – symbols with the symbols inside the
compartment.
V A R I A B L E O U T
5. Slide the cover back and turn the radio right
side up.
A U X I N
R
L
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
5
Setting Up
Connect the power cord
1. Plug the small end of the power cord into the power jack on the back of your radio (see
Figure 3). Line up the flat edge of the plug with the flat edge on the side of the jack.
Figure 3
Connecting the power cord.
R
AUX IN
L
120V AC
50/60Hz 50W
VARIABLE OUT
2. The FM antenna is built into the power cord. To improve FM reception, unwind the power
cord completely.
3. Plug the other end of the power cord into an electric outlet.
4. The display panel lights and the time display begins flashing after the power is connected.
Press the CLOCK SET button once to stop the flashing.
6
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Setting Up
Note:
The remote control
Replace only with a Duracell,
Eveready, Maxell, or Toshiba
CR2032 or DL2032 lithium battery
(available at most electronics
stores). If you have difficulty finding
a replacement battery, contact
Bose® Customer Service (see
phone numbers on the inside back
cover).
Install the battery
Your Wave® radio remote control has a security lock to prevent children from reaching the small
battery. Follow these steps to insert or remove the battery.
1. Place the remote control upside down and face down (as shown in Figure 4a).
2. Insert the tip of a pen into the small hole in the security lock (Figure 4a). If your pen does
not have a long fine point, you can use a straightened paper clip instead.
3. Tilt the pen to push the lock in the direction shown by the arrow in Figure 4b. Push the
lock until the battery compartment clicks open.
Note: If you have difficulty getting the lock to click open, use the pen to hold the lock to
the side while pulling the battery carrier out. You can place a thin coin or other object in
the battery carrier slot to help pull the battery carrier out.
Figure 4
Push the security lock toward the
battery carrier slot, until the battery
compartment lock clicks open.
battery carrier slot
b
a
b a t t e r y t o b e u s e d
i n s t r u c t i o n s f so r et y cp ue s rio tf y
lock
S e e o p e r a t i n g
b a t t e r y t o b e u s e d
o n o r t y p e s o f
r a t i n g
4. Slide the battery carrier out. Insert the battery into the battery carrier, with the + symbol
facing up, as shown in Figure 5.
5. Slide the battery carrier closed. Do not force it. It automatically locks in place.
Figure 5
Insert the battery with the + symbol
facing up.
WARNING:
The remote control battery may
cause a fire or chemical burn if
mishandled. Keep it away from
children. Do not recharge,
See operating
battery to be used
instructions for types of
disassemble, heat above 100˚C
(212˚F), or incinerate. Dispose of
used battery promptly. Replace
with a battery of the type and
model mentioned in the note
above. Using another battery may
cause a fire or explosion.
battery carrier
How to operate
Aim the remote control at your Wave radio. Use the remote keys in the same way you use the
radio control panel. The remote normally works up to 20 feet in front of the radio, and 6 feet to
either side. Replace the remote control battery when it stops operating, or its range seems
reduced (normally every year or two).
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
7
The Display
How to read the clock display
Figure 6A
The clock display.
[Numeric display] – Shows current time, wakeup time, time remaining before
automatic shutoff, station frequency, or volume setting.
Lights to indicate
Alarm 1 is on.
Lights to indicate
sound selected for
Alarm 1.
ALARM
AM
PM
Lights to indicate
sound selected for
Alarm 2.
ALARM 2
SLEEP
One will light to
indicate AM or PM.
Lights to indicate
Sleep Mode is selected.
Lights to indicate
Alarm 2 is on.
Note:
The display automatically adjusts
as the light in your room changes.
In normal lighting the display is
bright. In darker rooms the display
dims.
How to read the radio display
Figure 6B
The radio display.
Lights to show auxiliary source, FM, or
AM band selected.
Lights while
[Numeric display] –
Shows station
frequency, current
time, wakeup time,
time remaining before
automatic shutoff, or
volume setting.
receiving FM
stereo broadcast.
AUX FM
STEREO
Lights while
VOL AM
SEEK
volume setting
is displayed.
PRESET
1
2
3
4
5
6
Lights while
radio
automatically
searches for a
strong signal.
Lights when you
preset a station.
Lights when you select
a preset station.
8
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
The Display
How to customize the display
Function
Keys
Action
Press ON/OFF once to turn your Wave®
radio off.
AM/PM (12 hour)
or
ON/OFF
Military (24 hour)
time
Hold down CLOCK SET and press ON/OFF
to switch between AM/PM (12 HR) or military
(24 HR) formats.
CLOCK
SET
ON/OFF
AM/FM
and
In clock mode, the display shows the time
while the radio is on; in radio mode, the display
shows the radio station that is selected.
Clock or radio
mode
CLOCK
SET
With the radio turned on, hold down the
CLOCK SET button and press the AM/FM
button to switch between clock and radio modes.
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
9
Radio Functions
Radio Control Operation
To turn on/off
Press ON/OFF once to turn on (automatically selects the last
source played) or to turn off. Selecting any preset also turns
the radio on.
ON/OFF
Press AM/FM to turn the radio on. Press again to
switch between FM and AM.
AM/FM
AUX
Press AUX once to listen to a component connected to the
AUX IN jacks. (This does not turn on the component).
To shut off
automatically
Press SLEEP/SNOOZE to set automatic shutoff. The display
shows 75 minutes. Press again, or press and hold, to reduce
the time until shutoff to 60, 45, 30, 15, 10, 5, or 0 minutes.
SLEEP/SNOOZE
ON/OFF
AM/FM
Press ON/OFF to turn off the radio before automatic shutoff.
To select AM
or FM
If the radio is off or in AUX mode, press AM/FM to select
the radio. Press again to select AM or FM.
To adjust
volume
While the radio is on or off, press either VOLUME button and
hold to reset the volume.
The display shows the volume level from 0 (soft) to 99 (loud).
VOLUME
To display
the station
If the display is in clock mode and the radio is on, press both
TUNING buttons simultaneously to display the current station
for several seconds.
TUNING
To tune in
a station
Press and hold either TUNING button until the desired station
is selected.
TUNING
To seek
a station
Press and hold either TUNING button until you hear a beep.
Then release to find the next strong signal. Turn the volume
up, if necessary, to hear the beep.
TUNING
To preset up
to 6 AM and
6 FM stations
Use the TUNING buttons to find the desired station. Then,
hold down any PRESET button until you hear a beep. The
station is now preset to that button.
TUNING
PRESET STATIONS
To tune in
a preset
Choose AM or FM. Press the PRESET button for the station
you want.
PRESET STATIONS
AM/FM
10
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Radio Functions
Remote Control Operation
To turn on/off
Press ON/OFF once to turn on (automatically selects the last
source played) or to turn off. Selecting any preset also turns
the radio on.
ON/OFF
AM
FM
Press AM/FM to turn the radio on. Press again to
switch between FM and AM.
Press AUX once to listen to a component connected to the
AUX IN jacks. (This does not turn on the component).
AUX
To shut off
automatically
Press SLEEP to set automatic shutoff. The display shows 75
minutes. Press again, or press and hold, to reduce the time
until shutoff to 60, 45, 30, 15, 10, 5, or 0 minutes.
SLEEP
ON/OFF
Press ON/OFF to turn off the radio before automatic shutoff.
To select AM
or FM
If the radio is off or in AUX mode, press AM/FM to select
the radio. Press again to select AM or FM.
AM
FM
To adjust
volume
While the radio is on or off, press either VOLUME button and
hold to reset the volume.
The display shows the volume level from 0 (soft) to 99 (loud).
Press MUTE to silence the radio.
VOLUME
MUTE
Press again to restore volume.
To display
the station
If the display is in clock mode and the radio is on, press STA.
STA.
To tune in
a station
Press and hold either TUNING button until the desired station
is selected.
TUNING
To seek a
station
Press and hold either TUNING button until you hear a beep.
Then release to find the next strong signal. Turn the volume
up, if necessary, to hear the beep.
TUNING
To preset up
to 6 AM and
6 FM stations
Use the TUNING buttons to tune to the desired station. Then
hold down any PRESET button until you hear a beep. The
station is now preset to that button.
TUNING
1
4
2
3
6
PRESET STATIONS
5
To tune in
a preset
Choose AM or FM. Press the PRESET button for the station
you want.
1
4
2
3
6
AM
FM
PRESET STATIONS
5
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
11
Clock Functions
Radio Control Operation
While holding down the CLOCK SET button,
press either TUNING button. The time display
changes slowly at first, then more quickly. It
stops when you release the TUNING button.
To set the
clock
CLOCK
SET
TUNING
To set
Alarm 1
wake up
time and
alarm sound
Note: You can set the alarm with the radio on or off.
ALARM
SET
Hold down ALARM SET and press either TUNING
button. The time display changes slowly at first, then
more quickly. It stops when you release any button.
TUNING
To change the Alarm 1 sound, press ALARM MODE.
For tone only, press until the ( ) indicator lights.
When the alarm goes off, the tone volume gradually
increases to your preset level.
ALARM MODE
For radio only, press until the ( ) indicator lights.
When the alarm goes off, the radio volume gradually
increases to your preset level.
For tone and radio, press until both indicators (
)
light. When the alarm goes off, the tone sounds. After
you press SLEEP/SNOOZE, the radio turns on.
To set
Alarm 2
wake up
time and
alarm sound
Note: You can set the alarm with the radio on or off.
ALARM
SET
Hold down ALARM SET and press ALARM MODE. The
Alarm 2 indicator flashes. You now have 10 seconds to
begin setting Alarm 2.
ALARM MODE
Note: The Alarm 2 indicator must be flashing while setting
Alarm 2 wake up time or sound.
TUNING
To set Alarm 2 wake up time, hold down ALARM SET and
press either TUNING button.
ALARM MODE
To change Alarm 2 sound, press ALARM MODE while the
Alarm 2 indicator flashes.
For tone only, press until the ( ) indicator lights. When the
alarm goes off, the tone volume gradually increases to your
preset level.
For radio only, press until the ( ) indicator lights. When the
alarm goes off, the radio volume gradually increases to your
preset level.
For tone and radio, press until both indicators (
) light.
When the alarm goes off, the tone sounds. After you press
SLEEP/SNOOZE, the radio turns on.
Note: The Alarm 2 indicator continues flashing for 10
seconds after wake up time and sound are set.
12
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Clock Functions
Remote Control Operation
You cannot set the clock with the remote control.
To set the
clock
Note: You can set the alarm with the radio on or off.
To set
Alarm 1
wake up
time and
alarm sound
TIME ALARM
TUNING
Press TIME. The alarm indicator begins flashing.
Press either TUNING button. The time display changes
slowly at first, then more quickly. It stops when you
release any button.
Press TIME to return the display to the current time.
TIME ALARM
To change the Alarm 1 sound, press
.
For tone only, press until the ( ) indicator lights. When
the alarm goes off, the tone volume gradually increases
to your preset level.
For radio only, press until the ( ) indicator lights. When
the alarm goes off, the radio volume gradually increases
to your preset level.
For tone and radio, press until both indicators (
)
light. When the alarm goes off, the tone sounds. After
you press SLEEP, the radio turns on.
Note: You can set the alarm with the radio on or off.
To set
Alarm 2
Press TIME, then
now have 10 seconds to begin setting Alarm 2.
. The Alarm 2 indicator flashes. You
wake up
time and
alarm sound
TIME ALARM
TIME ALARM
Note: The Alarm 2 indicator must be flashing while setting
Alarm 2 wake up time or sound.
To set Alarm 2 wake up time, press either TUNING button.
Press TIME to return to the regular display.
To change Alarm 2 sound, press TIME to return to regular
display. Then press
while the Alarm 2 indicator flashes.
For tone only, press until the ( ) indicator lights. When the
alarm goes off, the tone volume gradually increases to your
preset level.
For radio only, press until the ( ) indicator lights. When the
alarm goes off, the radio volume gradually increases to your
preset level.
For tone and radio, press until both indicators (
) light.
When the alarm goes off, the tone sounds. After you press
SLEEP, the radio turns on.
Note: The Alarm 2 indicator continues flashing for 10
seconds after wake up time and sound are set.
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
13
Clock Functions
Radio Control Operation
To use
Auto Reset
While the alarm sounds, press ON/OFF once. The alarm
stops and resets to go off at the same time tomorrow. If you
do not turn off the alarm, it continues to sound for 30
minutes. Then it stops and resets to go off at the same time
tomorrow.
ON/OFF
To check
Alarm 1
Press ALARM SET. The display shows the wake up time
for Alarm 1.
ALARM
SET
To check
Alarm 2
Simultaneously press both ALARM SET and ALARM MODE.
The display shows the wake up time for Alarm 2.
ALARM
SET
ALARM MODE
For the radio ( ), use the VOLUME buttons to set the volume.
To set the
volume of
the alarm
For tone (
), choose the alarm sound (see page 12).
VOLUME
Set the alarm to go off. When the alarm sounds, press either
VOLUME button to adjust the volume.
Press ON/OFF to silence the alarm. This automatically resets
the alarm to repeat tomorrow.
ON/OFF
To snooze
When the alarm is in tone ( ) or radio ( ) mode, press
SLEEP/SNOOZE to pause the alarm for ten minutes.
SLEEP/SNOOZE
When the alarm is in tone and radio (
) mode, press
SLEEP/SNOOZE to pause the tone and hear the radio. The
tone sounds again in ten minutes. Press again to silence the
radio. The alarm indicator flashes while paused.
To stop
the alarm
Press ON/OFF once. The indicators remain lit. The alarm
repeats tomorrow.
ON/OFF
To turn off the alarm function, press ALARM MODE until
To disable
Alarm 1
the ( ) and (
) indicators do not appear on the display.
ALARM MODE
The alarm must be reset for next use.
Hold down ALARM SET and press ALARM MODE. Alarm 2
flashes on the display. Release ALARM SET. Press ALARM
To disable
Alarm 2
ALARM
SET
ALARM MODE
MODE until the ( ) and (
) indicators no longer appear.
To wake to
your favorite
station
Simultaneously press ALARM SET and any PRESET button.
The preset indicator and the station frequency flash on the
display.
ALARM
SET
PRESET STATIONS
Release the ALARM SET button. Alarm 1 plays this station
until you reset the alarm.
Alarm
operation
during a
Press ON/OFF to silence. Backup batteries run the alarm
for approximately a week during power failure. To conserve
power, only the tone sounds, even if radio is selected. Normal
operation resumes when power is restored. Batteries should
be replaced after an extended power failure.
ON/OFF
power failure
14
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Functions
Remote Control Operation
To use
Auto Reset
While the alarm sounds, press ON/OFF once. The alarm
stops and resets to go off at the same time tomorrow. If you
do not turn off the alarm, it continues to sound for 30
minutes. Then it stops and resets to go off at the same time
tomorrow.
ON/OFF
Press TIME on your remote control. The display shows the
wake up time for Alarm 1. Press TIME again to return to
normal display.
To check
Alarm 1
TIME ALARM
TIME ALARM
Press TIME. Then press
up time for Alarm 2.
. The display shows the wake
. The normal display returns.
To check
Alarm 2
Press TIME. Then press
To set the
volume of
the alarm
For the radio ( ), use the VOLUME buttons to set the volume.
For tone ( ), choose the alarm sound (see page 13).
Set the alarm to go off. When alarm sounds, press either
VOLUME button to adjust the volume.
VOLUME
ON/OFF
Press ON/OFF to silence the alarm. This automatically resets
the alarm to repeat tomorrow.
To snooze
When the alarm is in tone (
) or radio ( ) mode, press
SLEEP to pause the alarm for ten minutes.
SLEEP
When the alarm is in tone and radio (
) mode, press
SLEEP on your remote control to pause the tone and hear the
radio. The tone sounds again in ten minutes. Press again to
silence the radio. The alarm indicator flashes while paused.
To stop
the alarm
Press ON/OFF once. The indicators remain lit. The alarm
repeats tomorrow.
ON/OFF
To turn off the alarm function, press
and ( ) indicators do not appear on the display. The
alarm must be reset for next use.
until the (
)
To disable
Alarm 1
TIME ALARM
Press TIME. Then press
TIME again. Press
tors no longer appear on the display.
. Alarm 2 flashes. Press
until the ( ) and ( ) indica-
To disable
Alarm 2
TIME ALARM
To wake to
your favorite
station
Use the radio control panel to select this feature.
Alarm
operation
during a
Press ON/OFF to silence. Backup batteries run the alarm for
approximately a week during power failure. To conserve power,
only the tone sounds, even if radio is selected. Normal opera-
tion resumes when power is restored. Batteries should be re-
placed after an extended power failure.
ON/OFF
power failure
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
15
Other Components
Connecting other components
Use your Wave® radio to improve the sound of a CD player, cassette player, or TV. You can also
use your radio as extension speakers for the Bose® Lifestyle® music system. Connect one of these
components to the right and left AUX IN jacks. Or add powered Bose speakers connected to the
right and left VARIABLE OUT jacks. Audio cables for these connections are available at electron-
ics stores, or by calling Bose.
Most audio cables are color coded. Match the red plugs to the right (red) jack and the black or
white plugs to the left (white) jack (see Figure 7).
Connecting components or speakers to the VARIABLE OUT jacks will shut off the radio’s
speakers.
Figure 7
Location of jacks to use in connect-
ing other components.
R
AUX IN
L
120V AC
50/60Hz 50W
VARIABLE OUT
R
AUX IN
L
Connect red
plugs here
Connect white or
black plugs here
VARIABLE OUT
16
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
Other Components
Connection at
component
Connection at
Wave® radio
Note
Component
Cable
One miniplug-to-
stereo audio cable
Headphone jack (set
the headphone volume
control to 7).
Portable CD or
tape player
AUX IN jacks
Recording from your Wave radio
is not recommended because
connections to the VARIABLE
OUT jacks shut off the radio
speakers, preventing you from
monitoring the recording volume.
Audio output jacks
CD player, tape
deck, or VCR
One stereo audio
cable
AUX IN jacks
If there are two sets of
outputs, use the fixed
outputs.
Television
TVs with stereo output
jacks need a standard
RCA cord.
Audio output jacks
AUX IN jacks
To make sure the sound seems to
come from the screen, place the
Wave radio close to the TV.
If there are two sets of
outputs, use the fixed
outputs.
TVs with single (mono)
audio output jacks use
a standard Y adapter.
To prevent interference with the TV
picture, do not place the Wave radio
directly on top of the TV.
TVs with earplug outlets
may need a special
earplug adapter.
Bose® Lifestyle®
music system
25 to 100 foot stereo
cable with male-to-
male RCA plugs.
TAPE (REC) jacks
AUX IN jacks
Powered Bose
speakers
Use the audio-input
cables that came with
your speakers.
Speaker system input
as described in the
speaker owner’s
manual.
VARIABLE OUT jacks
Some Bose audio-input cables have
three connectors at each end. Use
only the two connectors that look
alike. DO NOT INSERT THE THIRD
CONNECTOR into the speaker’s
SYSTEM CONTROL jack.
Using other components
Choose your CD player, tape player, or other auxiliary source by pressing the AUX key. Adjust
the listening volume with the VOLUME keys. Control all other functions at the source, referring
to its owner’s manual, if necessary. Control your auxiliary powered speakers from the Wave
radio. If these speakers have a volume control, you may use it.
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
17
Product Information
®
Maintaining the Wave radio
The only necessary maintenance is periodic battery replacement and cleaning.
Replace the batteries
To protect your Wave radio’s memory and backup alarm system, replace the batteries every
year and when you have an extended power loss. Dead batteries may leak and cause damage.
Do not unplug your Wave radio from the power outlet while replacing the batteries. If you do
unplug it, you will need to reset the clock, alarm settings, and station presets. For further
information on replacing batteries, see “Install the batteries” on page 5.
For information on replacing the remote control battery, see “Install the battery” on page 7.
How to clean
Use only a cloth to clean the outside of the Wave radio. Do not use any solvents, chemicals, or
cleaning solutions containing alcohol, ammonia, or abrasives. Do not allow liquids to spill into
any openings on the radio. If necessary, you may use a soft-bristled attachment to gently
vacuum the front of the radio.
For best radio reception…
The Wave radio has an internal antenna. You may adjust the antenna by turning the radio
slightly.
You may adjust the FM antenna by moving the power cord. If you still have problems with FM
reception, you may need an external antenna. Call Bose® Customer Service to request one.
Features
• Acoustic Wave® speaker technology provides deep, full bass from a small enclosure.
• High performance stereo tuner allows 6 AM and 6 FM station presets.
• Automatic protection circuitry prevents speaker damage from excessive volume.
• Dual independent alarms let you set two wakeup times.
• Credit card-size remote offers convenient operation of the radio and clock functions.
Size
Dimensions
• 4.5"H x 14"W x 8"D (11.4 x 35.6 x 20.3 cm)
Weight
• 7 lb (3.2 kg)
Power rating
• USA/Canada: 120VAC~ 50/60 Hz 50W
18
Download from Www.SoJmaannuuaalsr.yco4m,.2A0ll0M2anuals Search And Download.
AM189930_01_V.pdf
®
Bose Corporation
Warranty period
The Bose Wave® radio is covered by a limited 1-year transferable warranty. Details of the
warranty are provided on the warranty card that came with your radio. Please fill out the
information section on the card and mail it to Bose.
Customer service
For additional help in solving problems, contact Bose customer service.
USA
1-800-637-8781 Monday through Friday, 8:00 a.m. to 9 p.m. ET
Canada
1-800-444-BOSE (1-800-444-2673) Monday through Friday, 9 a.m. to 5 p.m. ET
AM189930_01_V.pdf
Download fromJWawnwu.aSroym4an,u2a0ls0.c2om. All Manuals Search And Download.
19
Warranty
© 1996 Bose Corporation
The Mountain, Framingham, MA 01701-9168 USA
JN97832 PN189930 Rev.01 AM189930 Rev.01
Download from Www.Somanuals.com. All Manuals Search And Download.
|