Fire Alarm Control Panels
FPD-7024
en Installation and Operation Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Table of Contents | en
3
Table of contents
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
4
en | Table of Contents
Fire Alarm Control Panels
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Table of Contents | en
5
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
6
en | Notices
Fire Alarm Control Panels
1
Notices
1.1
FCC Compliance Notice
This equipment was tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, might cause harmful interference to radio communications. There is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, that can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
–
–
–
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
–
Consult the dealer or an experienced radio or TV technician for help.
1.2
FCC Phone Connection to Users
This control panel complies with Part 68 of the FCC rules.
On the inside of the enclosure is a label that contains, among other information, the ringer
equivalence number (REN) for this equipment. You must, upon request, provide this
information to your local telephone company.
The REN is useful to determine the quantity of devices that can be connected to your
telephone line and still have all of those devices ring when your telephone number is called. In
most, but not all areas, the sum of the RENs of all devices connected to one line should not
exceed five. To ascertain the number of devices that you can connect to your line, contact
your local telephone company to determine the maximum REN for your local calling area.
This equipment can not be used on coin service provided by the telephone company. Do not
connect this control panel to party lines. If this equipment causes harm to the telephone
network, the telephone company might discontinue your service temporarily. If possible, they
will notify you in advance. But if advance notice isn’t practical, you will be notified as soon as
possible.
You will be informed of your right to file a complaint with the FCC. The telephone company
might make changes in its facilities, equipment, operations, or procedures that could affect
the proper functioning of your equipment. If they do, you will be notified in advance to give
you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this equipment, contact the manufacturer for information on
obtaining service or repairs.
The telephone company might ask that you disconnect this equipment from the network until
the problem is corrected or until you are sure that the equipment is not malfunctioning. The
manufacturer, not the user, must make the repairs to this equipment. To guard against
accidental disconnection, there is ample room to mount the telco jack inside of the control
panel cabinet.
The operation of this control panel might also be affected if events such as accidents or acts
of God cause an interruption in telephone service.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Notices | en
7
1.3
Industry Canada Notice
The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective, operational, and safety
requirements. Industry Canada does not guarantee the equipment will operate to the user’s
satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to
the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of connection. The customer should be aware that compliance
with the above conditions might not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alterations made by the user to this
equipment, or equipment malfunctions, might give the telecommunications company cause to
request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the
power utility, telephone lines, and internal metallic water pipe system, if present, are
connected together. Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or electrician.
1.4
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
Microsoft, Windows, and Windows NT are either registered trademarks or trademarks of
Microsoft Corporation in the United States and/or other countries.
CYCOLOY is a registered trademark of Sabic Plastic.
POLYLAC is a registered trademark of CHI MEI Industrial Corporation, LTD.
CleanMe is a trademark of GE Interlogix, Inc. in the United States and/or other countries.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
8
en | Overview
Fire Alarm Control Panels
2
Overview
2.1
System overview
The FPD‑7024 Fire Alarm Control Panel is a fully integrated hard-wire fire alarm system. It can
support four input points (expandable to 255 using D7039 Multiplex Expansion Module and
the FPC‑7034 Four-Point Expander) and 16 individual users (expandable to 100 with the
D7039). The control panel has a built-in LCD keypad. Up to four additional keypads can be
used to provide user interface with the system and programming access for the installer. The
FPD‑7024 also includes the following features:
–
–
–
–
–
–
Built-in dual-line communicator
Menu driven keypad programming
Freely programmable alphanumeric/alphabetical display
99 event history buffer
16 user codes
UL Listed, CSFM, MEA Approved
When the D7039 Multiplex Expansion Module is installed, these additional features are
available:
–
–
–
247 additional addressable input points (255 total points)
499 Non-volatile event history buffer
100 user codes
For the location of the major items on the FPD‑7024 Control Board, see the following figure:
Figure 2.1: FPD-7024 ControlBoard
1 TELCO terminal strip
7 Keypad
2 Relay terminal strip
8 D7039 MUX expansion module
connector pins
3 Smoke power terminal strip
9 LCD display
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Overview | en
9
4 Zone input terminal strip
5 Option bus terminal strip
10 NAC terminal strip
11 Auxiliary power terminal strip
6 FPC-7034 point expander connector
pins
2.2
Components
2.2.1
On-board conventional points
All on-board points and points implemented with the FPC-7034 work with two- or four-wire
detectors. The system has an optional alarm verification feature.
Number of two-wire circuits
Type of Circuit
Four circuits, expandable to eight using an
FPC-7034 Expander
Class B, Style B and Class A, Style D as
needed)
EOL Resistor
2.21 kΩ (P/N: 25899 or F01U034504), UL
listed
Supervisory Existing
8 mA to 20 mA
25 mA
Required Existing for Alarm
Maximum Short Circuit Existing
Maximum Line Resistance
Circuit Voltage Range
45 mA
150 Ω
20.4 VDC to 28.2 VDC
20 detectors (two-wire)
3 mA maximum
Maximum Detectors per Point
Total Detector Standby Existing
Response Time1
Either fast (500 ms) or programmable (from
1 second to 89 seconds)
Dirty Detector Monitoring
Implements Bosch Security Systems, Inc.
Chamber Check and GE Interlogix, Inc.
CleanMe protocol to monitor conventional
loops for dirty detectors.
Table 2.1: Two-wire circuits
All on-board points, and points activated with the FPC‑7034 Four Point Expander, are
continuously monitored for detectors signaling a dirty condition using the Bosch Security
Systems, Inc. Chamber Check and GE Interlogix, Inc. CleanMe protocols. To prevent nuisance
reports, a two-minute delay occurs before a dirty detector is annunciated. A six-minute delay
occurs after the detector restores from the dirty condition before the control panel restores
the condition.
2.2.2
Off-board addressable points (with D7039 Multiplex Expansion Module)
The D7039 Multiplex Expansion Module adds:
–
Two Class B, Style 4 or one Class A, Style 6 Signaling Line Circuits (SLCs)
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
10
en | Overview
Fire Alarm Control Panels
–
Each point is individually supervised for proper connection to the common bus (when
over ten points are troubled, up to ten troubles are shown per bus and the balance of the
troubles is indicated by a common bus failure message).
–
–
Response time can be set to fast, or programmed from 1 to 89 seconds.
Input points on the SLCs are implemented with a D7042 Eight Input Remote Module.
2.2.3
Enclosure Housing
The standard enclosure is 18 ga., cold-rolled steel, and measures 20.75 in. x 15 in. x 4.25 in.
(52.7 cm x 38.1 cm x 10.8 cm). A keyed lock is included, and the LEDs and LCD display are
visible through the door.
2.2.4
2.2.5
2.2.6
Remote LCD Keypads
Maximum number of keypads: Four FMR‑7033 LCD Fire Keypads.
For wiring Requirements, see Option bus wiring requirements, 34
Remote LED Annunciators
Maximum number of annunciators: Eight D7030 eight-zone LED Annunciators.
For wiring Requirements, see Option bus wiring requirements, 34
D7032 - use with the D7030X
When a D7032 Eight-Zone LED Annunciator Expander is connected to the D7030X, eight
additional LED zones appear. This allows the D7030X/D7032 combination to show 16 LED
zones. Up to eight D7030X/D7032 combinations can be connected to the FPD‑7024 Fire Alarm
Control Panel.
Notice!
Each D7030X processes 16 zones of information. If no D7032 is attached, only the lower eight
zones are shown.
Notice!
The column labeled “shown on D7030X” in the LED assignments table below applies regard-
less if an attachment of a D7032 to any D7030X is made.
For LED assignments when up to eight D7030X/D7032 combinations are used, see the
following table:
D7030X
zones
shown on
D7030X
shown on
D7032 (if
attached)
comments
covered
1
2
1 to 16
1 to 8
9 to 16
Combination with lowest option
bus address (such as Address 1)
17 to 32
17 to 24
25 to 32
Combination with second lowest
option bus address (such as
Address 2)
3
33 to 48
33 to 40
41 to 48
Combination with third lowest
option bus address (such as
Address 3)
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Overview | en
11
D7030X
zones
shown on
D7030X
shown on
D7032 (if
attached)
comments
covered
4
49 to 64
49 to 56
57 to 64
Combination with fourth lowest
option bus address (such as
Address 4)
5
6
7
8
1 to 16
1 to 8
9 to 16
Fifth combination repeats first
combination
17 to 32
33 to 48
49 to 64
17 to 24
33 to 40
49 to 56
25 to 32
41 to 48
57 to 64
Sixth combination repeats second
combination
Seventh combination repeats third
combination
Eighth combination repeats fourth
combination
Table 2.2: LED assignments for LED Annunciators
For the LED display for Zones 49 to 64, see the following table.
LED
Zone
Description
User defined
User defined
1
49
2
50
3
(reserved)
52
4
General fire alarm monitor waterflow (non-silencable)
General fire alarm monitor (silencable)
5
53
6
(reserved)
55
7
General Supervisory (silencable)
General Waterflow (silencable)
8
56
9
(reserved)
58
10
11
12
13
14
15
16
General supervisory alarm (non-silencable)
(reserved)
(reserved)
61
General waterflow alarm (non-silencable)
(reserved)
63
General alarm monitor waterflow (non-silencable)
(reserved)
Table 2.3: LED display for Zones 49 to 64
See also
–
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
12
en | Overview
Fire Alarm Control Panels
2.2.7
Communicator
The communicator can report to two phone numbers or IP addresses with full single, double,
and back-up reporting. Communicates in SIA, Modem IIIa2, Contact ID, BFSK, and 3/1 and 4/2
Tone burst formats (available communication formats depend on phone or IP connection).
Notice!
The communicator must be enabled and configured to operate. The communicator and phone
line monitors are disabled in the default factory configuration.
Phone Line and Phone Number/IP Selection: To ensure the delivery of critical reports, the fire
panel has two phone lines and two phone numbers or IP addresses that can be used for
reporting. Reports can be directed to one or both of two phone numbers or IP addresses
using the Report Steering feature in the control panel programming. Note that Account
Number 1 is used with Phone Number/IP 1, and Account Number 2 is used with Phone
Number/IP 2. Except for test reports, the control panel automatically selects the phone line or
IP address to use. If the report is not successful after two attempts on Line 1, the control
panel automatically switches and uses Phone Line 2. One exception is when test reports
(manual or automatic) are sent. Test reports are sent every 4 hours to 28 days. Each time a
test report is sent, the control panel alternates phone lines. This happens even if the monitor
says the line is bad. If the user sends two manual test reports, both phone lines can be tested.
The first report uses one line, and the second uses the other line. During normal operation,
the automatic test uses a different line each day. Because the control panel automatically
selects which line to use, both phone lines must use the same dialing sequences for sending
reports. For example, a line that requires a 9 to be dialed for an outside line cannot be paired
with a line that does not require a 9.
Notice!
PBX lines and ground start lines do not comply with NFPA requirements for digital communi-
cation.
While the control panel is idle, the FACP monitors the primary and alternate telephone lines by
monitoring the line for trouble. The FACP monitors each line every 12 seconds. When a trouble
still exists after three samples (36 seconds), the FACP sends a trouble report and activates
the yellow trouble LED and trouble relay.
Danger!
If the central station receives the automatic test report only every other day, this indicates
that one phone line at the protected premises is inoperative.
Correct this condition immediately, because other critical reports can be delayed when the
communicator is trying to send the test signal through the inoperative phone line (once each
48 hours).
Supplemental Reporting: While two independent phone lines are required for UL864 Central
Station service, the FACP can be configured with one phone line if the control panel is used
only for supplemental reporting on a local, remote station or auxiliary system.
To install the control panel with only one phone line, connect a jumper from T1 to T2 and a
jumper from R1 to R2. These jumper connections are shown in the following figure:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Overview | en
13
Figure 2.2: Supplemental Reporting
1 Jumper from R1 to R2
2 Jumper from T1 to T2
3 House phone
4 TELCO line
2.2.8
2.2.9
Users
The system allows up to 16 individual users, or up to 100 users when the D7039 is installed. A
personal identification number (PIN, the four-digit code entered at the keypads) and an
authority level to determine which functions can be performed can be assigned to each user.
Lightning protection
Notice!
This system is intended for installation entirely within one building.
Metal-oxide varistors (MOVs) and spark gaps provide protection from lightning surges and
static discharges.
2.2.10
Battery backup calculation
To calculate the standby battery capacity required by NFPA when using the FPD‑7024, see the
two following tables:
Device
Quantity Standby
Total
Alarm existing/ Total alarm
device
existing/device standby
FPD‑7024
1
200 mA
44 mA
200 mA
380 mA
380 mA
Control Panel
FPC‑7034
Four‑Point
Expander
156 mA
D7035/B Octal
Relay1
8 mA + 30 mA 2
10 mA
8 mA + 30 mA 2
10 mA
D7048/B Octal
Driver Module
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
14
en | Overview
Fire Alarm Control Panels
Device
Quantity Standby
Total
Alarm existing/ Total alarm
device
existing/device standby
FMR‑7036
Annunciator
Keypad
80 mA
100 mA
132 mA
175 mA
175 mA
90 mA
D7030X
27 mA
35 mA
35 mA
1 mA
Eight‑Point LED
Annunciator1
D7030X‑S2
Eight‑Point LED
Annunciator
D7030X‑S8
Eight-Point LED
Annunciator
D7032 Eight‑
Point LED
Annunciator
Expander
FMR‑7033
Keypad1
80 mA
100 mA
150 mA
D7039 MUX
Expansion
Module
150 mA
D7042/B
18 mA
18 mA
Addressable
Eight Point Input
D7050 MUX
0.50 mA
0.50 mA
0.56 mA
0.56 mA
Photoelectric
Smoke Detector
D7050TH MUX
Photoelectric
Smoke Detector
FMM-7045 MUX
Pull Station
0.55 mA
0.55 mA
0.55 mA
0.55 mA
0.55 mA
0.55 mA
D7044 MUX
Single Input Fire
D7044M MUX
Mini Contact
Module
D7052 MUX Dual
Input Fire
0.55 mA
0.55 mA
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Overview | en
15
Device
Quantity Standby
Total
Alarm existing/ Total alarm
device
existing/device standby
D7053 MUX I/ O
Module Fire
0.70 mA
0.70 mA
Smoke Detectors
Bells, Horns, and
so on
Other Sensors
Other
Grand Total
Grand Total
Standby Existing
Alarm Existing
1 The 24 VDC existing requirements for the D7030X, FMR-7033 and D7035 are shown at 75%
of the 12 VDC level shown on the specification sheets for these models. The FPD-7024
regulates 24 VDC power from the battery to 12 VDC for these accessories.
2 Add 30 mA for each relay activated
Table 2.4: Standby battery capacity calculations
The units shown in the following table are Amp hours (Ah), and the calculations include a 20%
derating factor.
Grand Total Standby Existing (in amps)
CS
HS
Total Hours of Standby Required
(usually 24 or 60):
Total Standby Capacity (multiply CS x HS)
TS= CS x HS
Grand Total Alarm Existing (in amps)
CA
HA
Total Hours of Alarm Time Required
(usually 0.083 o 0.25):
Total Standby Capacity (multiply CA x HA)
TA= CA x HA
TC = TA + TS
C = TC x 1.2
Total Capacity Required (add TA + TS):
Required Capacity with 20% Derating
(TC x 1.2)
Table 2.5: Required battery size calculation
Notice!
The required battery size to support the system can be calculated using the tables for Stand-
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
16
en | Overview
Fire Alarm Control Panels
2.2.11
Required batteries for existing load
Use the following procedure to determine the battery requirements for your system:
–
Estimate the size of the battery required to support the standby load using the following
table:
Standby load battery Capacityr required
Capacity required for Capacity required for
size chart
for 24 hours
48 hours
60 hours
Grand Total Standby
Existing
100 to 200 mA
201 to 300 mA
301 to 400 mA
401 to 500 mA
501 to 600 mA
601 to 700 mA
701 to 800 mA
801 to 900 mA
901 to 1000 mA
1001 to 1100 mA
5.8
11.5
17.3
23.0
28.8
34.6
X
14.4
21.6
28.8
36.0
X
8.6
11.5
14.4
17.3
20.2
23.0
25.9
28.8
31.7
X
X
X
X
X
X
X
X
X
Table 2.6: Standby load battery size (Ah)
–
Estimate the size of the battery required to support the alarm load using the following
table:
Alarm load
Capacity
Capacity
Capacity
Capacity
Capacity
battery size
chart
required for
5 minutes
required for
10 minutes
required for
15 minutes
required for
30 minutes
required for
45 minutes
Grand Total
Alarm Existing
250 to
0.1
0.1
0.1
0.2
0.2
0.3
0.3
0.6
0.5
0.9
500 mA
501 to
999 mA
1.0 to 1.5 A
1.6 to 2.0 A
2.1 to 2.5 A
2.6 to 3.0 A
3.1 to 3.5 A
3.6 to 4.0 A
0.2
0.2
0.3
0.3
0.4
0.4
0.3
0.4
0.5
0.6
0.7
0.8
0.5
0.6
0.8
0.9
1.1
1.2
0.9
1.2
1.5
1.8
2.1
2.4
1.4
1.8
2.3
2.7
3.2
3.6
Table 2.7: Alarm load battery size (Ah)
–
Add the results together for the total battery size.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
–
Overview | en
17
Select the next larger standard battery for the system.
If the results show a requirement for a battery over 40 Ah, reduce the existing load or add an
external regulated fire protective signaling power supply.
2.2.12
Compatible devices
Device
Function
D7030 Eight Point LED
Annunciator
Identifies the location of a fire alarm for up to eight zones
allowed per system.
D7030X Eight Point LED
Annunciator
Identifies the location of a fire alarm for up to eight zones
allowed per system.
D7030X‑S2 Eight Point LED
Annunciator
An eight zone LED annunciator, of which two zones are
reserved for supervisory functions. It has Power and
Trouble LEDs plus eight zone LEDs that can be labeled
individually.
D7030X‑S8 Eight Point LED
Annunciator
An eight-zone LED annunciator, of which all eight zones are
reserved for supervisory functions. It has Power and
Trouble LEDs plus eight-zone LEDs that can be labeled
individually.
D7032 Eight Point LED
Annunciator Expander
Attaches to a D7030X and identifies the location of a fire
alarm for eight additional zones.
FMR‑7033 Alphanumeric LCD
Keypad
The FMR‑7033 LCD Keypad combines remote annunciator
and controller functions for the FPD‑7024. Up to four
keypads can be connected.
FPC‑7034 Four Point Expander Allows the FPD‑7024 Control Panel to support four
additional loops. The FPC‑7034 plugs into the control panel
and provides four Class B, Style 4 loops that are identical
in characteristics to the loops on the control panel. One
FPC‑7034 is allowed per system.
D7035/B Octal Relay Module
Provides eight Form C relay outputs for addition to the
system. The outputs are programmable and can be
activated by system events. Each output operates
independently of the other seven outputs for complete
flexibility. The D7035 connects to the option bus; up to
two are allowed per system. The D7035B comes installed
on a mounting skirt.
For required enclosure modification, see also the D7035
Installation Guide.
FMR‑7036 Fire Annunciator
Keypad
Establishes the location of a fire alarm.
FPP‑RNAC‑8A‑4C Remote NAC
Power Supply
Adds four NFPA 72 Class B, Style Y Notification Appliance
Circuits through the option bus and is supervised by the
control panel. The FPP‑RNAC‑8A‑4C connects to the option
bus of the FPD‑7024 control panel and up to four are
allowed per system.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
18
en | Overview
Fire Alarm Control Panels
Device
Function
D7039 Multiplex Expansion
Module
Provides either 2 two-wire (Class B, Style 4) multiplex
buses or 1 four-wire (Class A, Style 6) multiplex bus. In
Class A mode, up to 120 addressable points can be added.
In Class B Mode, up to 247 addressable points can be
added. The D7039 connects directly to the control panel.
One is allowed per system.
D7042/B Eight‑Input Remote
Module
Provides eight Class B, Style 4 input points. Connect up to
15 modules to MUX Bus A, and 15 on MUX Bus B. The
D7042 is powered by 12 VDC supplied by the option bus
power terminals, in addition to the two‑wire data
connection. The D7042 can not be used on a signal line
circuit (SLC) configured for Class A, Style 6 operation.
D7048/B Octal Driver Module
FMM-7045 MUX Pull Station
Provides eight open‑collector transistor outputs for
addition to the FPD‑7024 Fire Alarm Control panels. It
connects to the control panels through the option bus.
UL Listed fire alarm initiating device.
D7044 MUX Single Input
Module
Connects a normally‑open contact device to the multiplex
bus of the FPD‑7024 with a supervised local loop. The
D7044 draws operating power from the FPD‑7024.
D7044M MUX Mini Contact
Module
Connects a contact device to the multiplex bus of the
FPD‑7024 with a supervised input loop. The D7044 draws
operating power from the FPD‑7024.
D7052 MUX Dual Input Fire
Connects to the multiplex bus of the FPD‑ 7024 and
provides two supervised input zones for connecting
conventional normally-open inputs. The D7052 draws
operating power from the FPD‑7024.
D7053 MUX I/O Module Fire
Connects to the multiplex bus of the FPD‑7024 and
implements a supervised local loop, and a Form C relay
output. Up to 20 modules can be connected to each MUX
bus. The D7053 draws operating power from the
FPD‑7024.
D7050/TH MUX Smoke Detector The D7050/TH is a photo-electric smoke detector with a
heat option. It connects to the multiplex bus of the
FPD‑7024. The D7050 draws operating power from the
FPD‑7024.
DX4020 / B420 models
The Conettix DX4020 and B420 models are communication
devices that manages secure, two-way IP communications
over Ethernet networks.
ITS‑DX4020‑G
The ITS-DX4020-G enables two-way IP or dialed
communications over a commercial GPRS/GSM network.
Typical applications are event reporting to a central
monitoring station and remote access to Bosch control
panels.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Overview | en
19
Table 2.8: Compatible devices
Install D7042 modules only at addresses:
9
17
25
33
41
49
57
65
73
81
89
97
105
169
233
113
177
241
121
185
129
193
137
201
145
209
153
217
161
225
Do not install D7052 and D7053 modules at these addresses:
16
24
32
40
48
56
64
72
80
88
96
104
168
232
112
176
240
120
184
248
128
192
255
136
200
144
208
152
216
160
224
Table 2.9: Address restrictions for the D7042, D7052, and D7053
2.3
Parts List
The FPD‑7024 comes with:
–
–
–
One FPD-7024 Control/Communicator in static-resistant bag
One enclosure with transformer
One hardware pack containing the hardware necessary for installing the control panel in
the enclosure
–
–
One enclosure lock, washer, and keys
Six end-of-line (EOL) resistors
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
20
en | Fire Safety
Fire Alarm Control Panels
3
Fire Safety
Danger!
No fire detection device or system is 100% foolproof.
This fire alarm system can provide early warning of a developing fire. Such a system, however,
does not ensure protection against property damage or loss of life resulting from a fire. Any
fire alarm system can fail to warn for any number of reasons (such as smoke not reaching a
detector that is behind a closed door).
Notice!
This system must be regularly tested (when installed, when modified, and at least annually
thereafter) to ensure continued performance.
When considering detectors for residential applications, refer to NFPA Standard 72, The
National Fire Alarm Code. This standard is available at a nominal cost from: The National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269.
3.1
Smoke detector layout
3.1.1
General considerations
Proper location of detection devices is one of the most critical factors in a fire alarm system.
Smoke detectors should not be installed in dead air spaces or close to ventilating or air
conditioning outlets because smoke can be circulated away from the detector. Locations near
air inlets are favored.
Avoid areas subject to normal smoke concentrations such as kitchens, garages, or near
fireplaces.
Do not install smoke detectors where normal area temperatures are above +100°F (+38°C) or
below +32°F (0°C).
Avoid areas of high humidity and dust concentrations.
Place the edge of ceiling mounted detectors no closer than 4 in. (10 cm) from any wall.
Place the top edge of wall-mounted detectors between 4 in. and 12 in. (10 cm and 30 cm)
from the ceiling.
For exact mounting information, refer to the instructions provided with the smoke detectors.
3.1.2
Family residences
Providing a Fire Warning System: Most fire deaths occur in the home, especially during
sleeping hours. The minimum level of protection requires smoke detectors to be installed
outside of each separate sleeping area and on each additional story of the dwelling.
Notice!
For added early warning protection, install detectors in all separate areas including the base-
ment, bedrooms, dining room, utility room, furnace room, and hallways.
For residential smoke detector locations, see the following figure:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Fire Safety | en
21
Figure 3.1: Smoke detector locations in residential settings
1 Bedroom
2 Hall
5 Basement
6 Recreation room
7 Kitchen
3 Living room
4 Dining room
* Smoke detector
3.2
Having and practicing an escape plan
A fire warning can be wasted unless the personnel planned in advance for a rapid and safe exit
from the building.
Draw a floor plan of the entire building showing two exits from each sleeping area and two
from the building. Since stairwells and hallways can be blocked during a fire, provide exits
from sleeping area windows. Make copies of the plan and practice it with all personnel.
Arrange a meeting place outside and away from the building. Once out of the building, all
occupants should immediately go to the pre-selected location to be accounted for.
Provide a barricade between personnel and fire, smoke, and toxic gases (such as closing all
sleeping area doors before retiring).
Instruct children on opening their bedroom windows and exiting safely from the building. If
exiting is not possible, teach them to stay at the open window and shout for help until it
arrives.
If a fire alarm occurs after retiring, wake the children by shouting to them from behind your
closed door. Tell them to keep their bedroom doors closed.
If the top of your bedroom door is uncomfortably hot, do not open it. There is most likely fire,
intolerable heat, or smoke on the other side. Shout to all family members to keep their
bedroom doors closed and to exit the building by alternate routes.
If the top of the door is not uncomfortably hot, brace the bottom of the door with your foot,
and the top with one hand, then open the door about one inch. Be prepared to slam the door
shut if there is any pressure against the door or if any hot air rushes in.
If there is no evidence of excessive heat or pressure, leave the room and close the door
behind you. Shout appropriate instructions to all family members and immediately leave the
building by the planned routes. If heavy smoke is present, drop to your hands and knees, or
crawl to remain below the smoke level.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
22
en | Installation
Fire Alarm Control Panels
4
Installation
4.1
Installation guide for UL Listed systems
4.1.1
FPD‑7024 UL Listings
The FPD‑7024 is UL Listed for the following:
–
Commercial Fire Alarm (UL Standard UL864)
–
–
Type Service: Auxiliary, Local, Central Station, and Remote Station
Type Initiating: Automatic, Manual, Sprinkler Supervisory, and Waterflow
Install the control panel according to NFPA 72 for Commercial Fire installations.
4.1.2
Installation considerations
Failure to install and program the control panel according to the requirements in this section
voids the listing mark of Underwriters Laboratories.
–
–
–
–
–
–
The standby battery capacity is 40 Ah at 24 VDC.
The total nominal existing must not exceed 1.25 A in standby or 4 A when in alarm.
The control panel must be mounted indoors and within the protected area.
Grounding must be according to article 250 of the NEC (NFPA 70).
Points must be connected to UL Listed, compatible devices.
The ground wire provided with the enclosure must be connected between the door and
the enclosure using the supplied nuts.
–
–
Do not program the ground start feature.
Select Phone Monitoring if the digital alarm communicator transmitter (DACT) feature is
used.
4.1.3
UL requirements
Notice!
The system must be tested after installation and after any re-programming, including pro-
gramming performed by downloading.
When used in UL Listed installations, the control panel must conform to certain programming
requirements. For a list of the required program entries specific UL Listed installations, see
Commercial Fire Alarm (Central Station [DACT] and Local)
Required Accessories
–
At least one Bosch Security Systems, Inc. Model F220‑P Smoke Detector with an F220
Family Base; or another UL Listed compatible smoke detector.
–
At least one Horn Strobe or Bell (provides 85 dB for UL985 and NFPA 72 requirements;
other UL Listed compatible devices listed for regulated 24 V can be used) is required for
this application and must be installed inside the protected area.
Four-wire detectors must be used with UL Listed power supervision devices. A
compatible UL Listed four-wire detector is the Bosch Security Systems, Inc. F220‑P in an
F220‑B6 Family Base. A compatible UL Listed relay is the Bosch Security Systems, Inc.
D275.
–
–
All points must be used with the resistor provided.
Report Programming
–
–
–
–
Program non-supervisory and supervisory reports for those points used.
Program trouble reports.
Set AC Failure Report Delay for a delay of 1 hour to 3 hours.
Set automatic test report frequency to occur at least every 24 hours.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Installation | en
23
Timer Programming
–
Program Auto Silence Time for not less than five minutes, or to “0” to disable auto-silence
operation.
Point Programming
For fire points: open = trouble, latching.
Alarm Output Programming
Program notification appliance circuits to activate from the appropriate input points.
Communications Programming
–
–
–
If used for Central Station Service, select a communication format compatible with the
central station. Enable monitoring of both phone lines.
UL Listed Accessory Devices
D132B Multi-use Reversing Relay Module
The D132B is a multi-purpose, fully configurable, smoke power-reversing module for activating
detectors with local annunciation. The D132B operates both two-wire and four-wire circuits
and also works with Class A or Class B initiating circuits. An alarm latch connection is
provided to allow an initiating loop to be held in alarm after the detector loop power is
reversed to activate any sounders. The D132B does not affect compatibility between the FACP
and detectors, or the FACP and Notification Appliance Circuits (NACs).
See also the D132B Installation Guide for detailed installation instructions for the D132B
module. One of the installation options shown in the D132B Installation Guide is also shown in
the following figure:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
24
en | Installation
Fire Alarm Control Panels
Figure 4.1: Wiring the D132B smoke power reversing module
1 Power limited and supervised
2 Optional alarm latch
3 Loop
7 12/24 VDC
8 24 V reversing detectors
9 2.2 kΩ EOL (power limited and
supervised)
4 Class A
5 Latch
10 Not used
11 24 V NACs
6 NAC
D185 Reverse Polarity Module
The D185 Reverse Polarity Module is a UL Listed module that connects the control panel with
either a single set or a pair of leased telephone company (TELCO) lines in NFPA 72 remote
station applications. It relays system alarm status information from the control panel to a
monitoring station. The D185 operates with either 12 VDC or 24 VDC supply.
For typical wiring of the D185 module, see the following figure:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Installation | en
25
Figure 4.2: Wiring the D185
1 D185 module
2 To monitoring station
3 D275
5 Fire control panel
bk black
bu blue
4 2.2 kΩ EOL
ye yellow
The module can signal alarm, trouble, and supervisory conditions. The Wiring the D185 figure,
24 shows the module being used to signal alarm and trouble conditions only. With a third relay
(available from the eight-relay expansion module) and an additional leased line, supervisory
conditions can also be signaled.
In the example in the Wiring the D185 figure, Relay 1 must be programmed to operate on
Alarm (Zone 63) and Relay 2 must be programmed to operate on Trouble (Zone 62). Program
Input 4 to operate as a Supervisory point. Any alarm causes the voltage to the monitoring
station to be interrupted. Placing the D185 in test mode causes a SUPERVISORY TROUBLE.
See also the D185 Installation Manual.
4.2
Installing the enclosure
To install the enclosure, follow these instructions:
1. Using the enclosure as a template, mark the top mounting holes on the mounting surface.
2. Start the mounting screws (not supplied) for these two holes.
3. Slide the enclosure onto these screws so that the screws rest on the thinner section of
the holes.
4. Tighten the screws.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
26
en | Installation
Fire Alarm Control Panels
5. Install and tighten the remaining two screws in the bottom mounting holes.
6. Knock out the desired wire entrances on the enclosure.
For mounting hole locations, see the following figure:
Figure 4.3: Enclosure iInstallation
1 Control panel location
5 Transformer
6 Stud
2 Mounting holes
3 Retainer holes for standoffs
4 Retainer holes for support posts
7 Ground wire
Notice!
If using the knockouts located at the bottom of the enclosure, install batteries in a separate
enclosure.
4.3
Installing the FPD‑7024
Danger!
The control circuit board in the FPD-7024 is static sensitive.
To avoid damage to sensitive components, touch ground before handling the control board.
This discharges any static electricity in your body. For example, run the ground wire to the en-
closure before handling the control circuit board. Continue touching the enclosure while in-
stalling the control board.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Installation | en
27
Warning!
Before the circuit board is installed, connect the supplied ground wires between the door and
the enclosure and from the transformer to the enclosure using the supplied nuts. Both
grounds connect to the stud in the enclosure to the left of the circuit board.
!
1. Insert the three support posts in the enclosure’s retainer holes.
2. Press the 1/8 in. nylon standoffs (P/N: F01U034705) into the retainer holes.
3. Slide the top of the control panel onto the retainer tabs (the slots under the top of the
frame). When the control panel is in the retainer tabs, it rests on the posts.
4. Secure the bottom of the circuit board by inserting and tightening the screws at the two
bottom corners through the support posts and the retainer holes.
For installing standoffs and support posts, see the following figure:
Figure 4.4: Standoff and support post installation
1 1/8 in. nylon standoff
4 Corner of circuit board
5 Support post
2 Retainer holes
3 Support post assembly
6 Retainer hole in enclosure
4.4
Installing optional equipment
Two expansion options connect directly to the control panel, and are automatically detected
and supervised when the control panel is powered:
–
–
FPC-7034 Four Point Expander
D7039 Multiplex Expansion Module
When the control panel is powered after installing one of these options, the control panel
displays one of the following windows:
4Z EXP DETECTED
PRESS BACK KEY
MUX DETECTED
PRESS BACK KEY
Press the [*/BACK] key to confirm the installation of the device and automatically set it up for
supervision.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
28
en | Installation
Fire Alarm Control Panels
If the [*/BACK] key is not pressed during the power-up time-out period, the control panel
resumes operation using the last confirmed status of the affected expander and displays an
installation error condition.
Warning!
Expansion devices such as point expanders and multiplex expanders are disabled if they are
removed from the control panel configuration after installation. You cannot disable supervi-
sion of these devices when they are installed.
!
For additional information, see the installation instructions for the specific expanders.
Notice!
EEPROM fault at first installation
When the D7039 Multiplex Expansion Module is first installed, the system displays an EE-
PROM fault. Execute the default procedure to synchronize the EEPROM on the expansion
module to the EEPROM in the control panel. Remove power to the control panel, then reapply
power and re-install option bus devices after the default procedure.
Notice!
Loss of programming
Replacing a D7039 Multiplex Expansion Module causes the loss of programming of expansion
points and PINs. Reprogram all multiplex point and PINs if you replace the D7039.
When the D7039 is first installed, or anytime the control panel is powered with a D7039 that
has no points programmed, the system automatically starts the multiplex auto-programming
process:
AUTO PROGRAM?
_______:YES(1) NO(0)
Pressing the [1] key starts auto-programming, and pressing [0/Prog] allows the control panel
to continue normal startup. The menu automatically closes with NO selected if no key is
pressed after several minutes.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Connection | en
29
5
Connection
5.1
FACP terminal connection
Danger!
Incorrect connections may result in damage to the unit and personal injury.
Warning!
Before servicing this equipment, remove all power including the transformer, battery and
phone lines.
!
Notice!
Shared cable is not recommended for option bus, telephone or NAC wiring.
Figure 5.1: Typical 2-wire smoke detector wirin (supervised)g
1 Class A, Style D
2 Class B, Style B
3 EOL resistor
Figure 5.2: Typical 4-wire smoke detector wiring
1 Class A, Style D
2 Class B, Style B
3 EOL relay
4 EOL resistor
5 Smoke detector
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
30
en | Connection
Fire Alarm Control Panels
Notice!
All wiring except battery terminal and primary AC power is power-limited. Primary AC and bat-
tery wires must be separated from other wires by at least ¼ in. (64 mm) and tied to prevent
movement.
Figure 5.3: Transformer
RD
red
BN
brown
supervised:
YE
yellow
white
black
WH
BK
Figure 5.4: Input Points
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Connection | en
31
Unsupervised:
1 Relay 1
Switched unsupervised:
4 Earth ground
2 Relay 2
5 Smoke detector
3 Relay 3
Input Points 1-4:
(supervised) Points are intended for connection of normally-open/normally-closed alarm
contacts. They may also be used for compatible two-wire smoke detectors. All EOL resistors
are 2.21 kΩ, P/N: 25899 Bosch, UL listed. Initiating devices are Class B, Style B or Class A,
Style D. Two‑wire Compatibility Identifier "A".
Notice!
For connection to listed power limited Class 2 or Class 3 sources only. Contacts rated at
5.0 A, 24 V.
Notice!
Smoke Power: 24 V, 1.0 A maimum (filtered).
For compatible devices, see also Technogram P/N: F01U0790.
Figure 5.5: Telephone lines 1 and 2
1 Phone Line 2 (supervised)
2 Phone Line 1 (supervised)
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
32
en | Connection
Fire Alarm Control Panels
DX4020,
B420 models,
ITS-DX4020-G
Figure 5.6: Keypad Connection (supervised, Class B, Style 4, 500 mA maximum)
Figure 5.7: Backup Batteries
1 Class B, Style Y
2 Class A, Style Z
3 Backup batteries
EOL End of line
supervised:
BAT Battery
BK black
RD red
Notice!
Unswitched unsupervised Auxiliary Power: 24 V, 1.0 A maximum (unfiltered).
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Connection | en
33
Danger!
Explosion and burn hazard!
Do not short terminals!
Notification appliance circuit:
NAC 1+
NAC 1-
+24 V while in alarm; ground while in standby.
Ground while in alarm; supervisory voltage while in standby.
Notification appliance circuit:
NAC 2+
NAC 2-
+24 V while in alarm; ground while in standby.
Ground while in alarm; supervisory voltage while in standby.
Batteries:
BAT -
BAT +
Requires two 12 V batteries in series, for a combined voltage of 24 V.
Charge current = 1.1 A, maximum
Use only indicating devices as listed on Technogram P/N. F01U010791.
5.2
Power supply connection
Use wire nuts to connect the primary side of the transformer in one of the following ways:
–
–
black and white wires to an unswitched 120 V, 60 Hz, or
yellow and white wires to an unswitched 240 V, 50 Hz circuit.
Danger!
Shock Risk!
Do to risk of shock and/or damage to the transformer a wire mut must be in place over the
unused black or yellow wire.
Connect the earth ground to the threaded ground stud on the left side of the enclosure.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
34
en | Connection
Fire Alarm Control Panels
Figure 5.8: Transformer Connections
Primary:
YE yellow
BK black
WH white
5.3
Option bus wiring requirements
Use 18 AWG (1.2 mm) or larger wire to connect option bus devices to the FACP. The total
length of wire connected to the option bus terminals must not exceed 4 000 ft (1 219 m),
regardless of the wire gauge wire used.
Notice!
Shared cable is not recommended for option bus, addressable points bus, telephone, or NAC
wiring.
Notice!
To comply with UL, do not share supplementary devices with primary device on the option
bus.
Avoid shielded or twisted pair-wire except for special applications where a reduced length of
wiring (approximately 50%) is acceptable for tolerating a harsh electrical environment.
The length of wire allowed between the control panel and the last device on a wiring run
depends on the existing current draw on that wiring run. Reducing the number of devices on a
wiring run allows the individual runs to be longer.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Connection | en
35
Add together the alarm existing current draw by all the devices on the wiring run to determine
the maximum allowed distance between the option bus terminals on the control panel and the
last device on the wire run (the device farthest from the control panel).
To determine the maximum allowed length for the run, add up the total alarm load for option
bus devices on the wire run. For example, if the total load of option bus devices on a
particular run is 400 mA, the maximum length of the run can be up to 500 ft (152 m). No more
than 4 000 ft (1 219 m) of wire can be connected to the option bus terminals, even if the
individual lengths of the runs are all within limit.
For the allowed lengths for18 AWG (1.2 mm) wire, see the following figure:
Figure 5.9: 18 AWG cable length for existing current draw
Notice!
The graph is for 18 AWG cable!
For16 AWG (1.5 mm) wire, cable lengths can be 1.5 times longer. For14 AWG (1.8 mm) wire,
cable lengths can be 2.5 times longer. The 4 000 ft (1 219 m) maximum length of connected
wire still applies.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
36
en | System Operation
Fire Alarm Control Panels
6
System Operation
6.1
Modes of Operation
There are four modes of system operation for the FPD‑7024: normal, alarm, supervisory, and
trouble.
6.1.1
Normal
When the system operates normally, it shows SYSTEM NORMAL on the top line of the display,
the Power LED lights steadily, and no other LEDs are lit. The bottom line indicates the existing
date MM/DD/YY and time HH:MM. If the system is programmed to require a PIN, the second
line of the LCD screen shows ENTER PIN.
6.1.2
Off-normal Displays
Control panel alarms and problems are indicated on the top line of the display. Contact your
installing company if problems persist.
For the alarm/problem messages, see the following table:
Off-Normal Display
XXX/XXX FIR: XXXXX
XXX/XXX SUP: XXXXX
XXX/XXX TRB: XXXXX
Description
One or more fire or waterflow points are in alarm.
One or more supervisory conditions exist.
A trouble condition exists (AC power failure, phone line
trouble, and so on).
Table 6.1: Off-normal displays
6.1.3
6.1.4
Acknowledge
When the control panel is off-normal, the control panel’s piezo (buzzer) can be silenced
without silencing the NACs or resetting the control panel. Press the [ACK] button on the local
or remote keypad to silence only the piezo.
Alarm
When an alarm occurs, the top line shows the number of alarms and the point that is in alarm.
The bottom line alternates between the instructions and the programmed description for the
affected point. When you back out of the detail view and go to the group view by pushing the
[4/<] key, the top line of the display shows ALARM (XXX), where XXX indicates the number of
alarms. This display overrides any other system display. The built-in sounder turns on with a
steady tone, and outputs programmed to activate with the existing alarm condition(s)
activate.
When the control panel is not scanning the inputs, as during smoke power reset, alarm
verification delay, or on-site programming, the trouble LED flashes to indicate this condition.
6.1.5
Supervisory
When a Supervisory condition occurs, the top line shows the number of supervisories and the
point that is in the supervisory condition. The bottom line alternates between the instructions
and the programmed description for the affected point. When you back out of the detail view
and go to the group view by pushing the [4/<] key, the top line of the display shows
supervisory (XXX), where XXX indicates the number of supervisory conditions. The bottom line
indicates more instructions. The built‑in sounder beeps. Outputs programmed to activate with
the existing condition(s) then activate.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
37
6.1.6
Trouble
When a trouble condition occurs (such as cut wiring for a point or AC power fails), the
sounder beeps every 10 seconds. The Trouble LED lights and the LCD shows the trouble
condition. When you back out of the detailed screen when the [4/<] key is pressed the group
is entered and shows TROUBLE (XXX). The system can diagnose and show a variety of trouble
conditions, including those affecting the input points, NAC circuits, power, battery, system
grounding, and internal operations of the fire control panel. Notify your installing company
immediately if the system trouble message appears.
Press the [Acknowledge] key to silence the system trouble beep.
6.1.7
Fire Silence/Reset
Danger!
Fire Alarm!
During a fire alarm, exit from the premises immediately. Do not enter the premises unless ac-
companied by the appropriate emergency services' personnel, or until they have given the OK
to enter.
DANGER!
When it is determined that there is no fire, you can silence the horns or bells to allow more
investigation of the devices that initiated the alarm, or you can reset the system to return it to
normal operation.
Notice!
Before resetting fire alarms
Before using the [Reset] key, determine which smoke detector sounded the alarm so that the
monitoring company can check that the system is operating correctly. If the control panel is
being used as an addressable control panel, use the [History] key to determine which address
is in alarm.
NOTICE!
If the system is configured to allow alarm silencing, the [Silence] key turns off the horns or
bells, but does not reset the alarm status and does not return the activated input to normal
service. Detectors that were activated stay in alarm and can be checked (usually by observing
an LED on the device) to see which detector caused the alarm. When the detectors causing
the alarm are identified, reset the system to return it to normal service.
The [Reset] key clears the system alarm status, and briefly turns off power to the detectors to
reset them. This command is required after any fire alarm affecting a point programmed for
latching operation (which is the normal configuration). This operation is also required to reset
Class A, Style 6 multiplex (SLC) wiring fault troubles.
The software automatically supervises the system software for proper operation. If the system
fails, a CPU FAULT message appears, and the nature of the failure can be optionally recorded
in the history buffer. To enable history buffer recording for CPU faults, program Output Zone
D of onboard Relay 2 to Zone 51 (unused). The history buffer message, if enabled, shows
CPUFLTxxx, where xxx is an error code. If the display shows CPU FAULT, contact Bosch
Security Systems, Inc. Technical Support and report the history buffer code along with a
description of the operations that caused the fault. Unusual conditions during programming
and debugging operations can result in a CPUFLT message in the history buffer. If, this occurs
when the control panel is in service, report it to Technical Service.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
38
en | System Operation
Fire Alarm Control Panels
6.2
Basic System Use
6.2.1
Function keys
A keypad that does not require a PIN number shows (under normal conditions) SYSTEM
NORMAL on the top line, and existing date and time on the bottom line. On a keypad that
does require a PIN number, enter the PIN number first. This enables the function keys.
6.2.2
Selecting menu items
Depending on which level in the system, (menu, sub-menu, sub-sub-menu), you can select an
item three different ways:
1. In the main menu, TEST, HISTORY, DISABLE, and DRILL each have an exclusive key on the
keypad. To select one of these menu items, press the corresponding key. For example, to
select TEST, press the [TEST] button.
2. The [PROG] and [ENTER] keys are not exclusive, but are shared with other characters.
The character sharing the corresponding key appears in the second line following a
forward slash (\). To select one of these items, press the corresponding key. For
example, the [PROG] key is also 0.
3. The key corresponding to a sub-menu item might appear in the second line preceding a
dash. Press the corresponding key to select that item. For example, press [1] to select
PROG TIMES.
While a menu is active, you do not need to wait for the desired menu item to appear before
making your selection. You can select any item on the existing menu rotation at any time.
6.2.3
After a Main Menu item is selected
When a main menu item is selected, the keypad might prompt you to enter your PIN. If so,
enter the number (factory default is 9876) and press the [#/Enter] key (or press the key
labeled with the desired command directly). The display automatically retrieves the sub-menu
display.
6.2.4
6.2.5
Returning to an earlier screen
To return to a previous screen at any time, press the [*/Back] key. To return to the SYSTEM
NORMAL display, press the [*/Back] repeatedly until you reach SYSTEM NORMAL. When you
reach SYSTEM NORMAL, you cannot go any farther.
Entering data
When a sub-menu item asks you to enter data, enter the data and press the [#/Enter] key. If
data already exists at a particular location, you can either accept that data or enter new data.
When you press the [#/Enter] key to enter the data, the display returns you to the previous
sub-menu display.
6.2.6
6.2.7
Drill
The drill command activates all NACs and no relays. It creates a history log entry and, as an
option, can be reported to the central station.
Disable
Use the disable command to disable input points, outputs, or the dialer. When any device is
disabled, the system shows this condition on the LCD and on the system trouble LED. The
Disable All Inputs operation takes several seconds to perform, during which time the system
display remains fixed.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
39
6.2.8
History
Notice!
If a system without a D7039 Multiplex Expansion Module loses all power (AC and standby bat-
tery), all history events are cleared.
The HISTORY option is a chronological list of system events that occurred. Press the [History]
key to HISTORY select from the Main Menu (SYSTEM NORMAL display).
On an FPD-7024 FACP with a D7039 Multiplex Expansion Module, up to 499 History events are
supported.
On an FPD-7024 FACP without a D7039 Multiplex Expansion Module, up to 99 History events
are supported.
After you press the [History] key, the most recent system event appears on the top line of the
LCD with the time and date below it.
Example: (Assume you pressed the [History] key at the Main Menu):
While the first event shows, the bottom line toggles every four seconds between the time and
date that the event occurred.
To return to a previous screen in the history buffer, press [2/▲].To scroll to the next event
record, press [8/▼].
For abbreviations used in history events, see the following table:
Abbreviation
ALRM
Meaning
Abbreviation
OFFNORM
PH1
Meaning
Alarm
Off Normal at Test
Phone Line 1
Phone Line 2
Restore
ARST
Alarm Restore
Auto Test
AUTOTST
BATT:LOW
BAT:RSTR
CPUFLT
DBL
PH2
Battery Low
Battery Restore
Internal Error
Disable
RSTR
S
Supervisory
SMK:FLT
SYSRESET
SYSRST
SYSTRB
SYS:WDOG
Smoke Power Fault
System Reset
System Restore
System Trouble
DRILL:BEG
DRILL:OVR
DRST
Drill Begin
Drill Over
Dirty Restore
Automatic CPU Reset
(Watchdog)
DRTY
DSBL
EE2
Dirty
TRBL
Trouble
Disable
EEPROM
Enable
Fire
TRST
Trouble Restore
Test Begin
Test Over
TST:BEG
TST:OVR
W
ENBL
F
Waterflow
MANULTST
Manual Test
Table 6.2: History event abbreviations
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
40
en | System Operation
Fire Alarm Control Panels
6.2.9
Remote Programming
Call for remote programming
Phone Numbers 1 and 3 must be programmed, along with Account Code 1. The control panel
calls Phone Number 3 and attempts to connect for downloading. If the control panel is already
using the phone line, it sounds the three-beep error tone. This function requires an access
code with programming authority (Level 1).
Answer for remote programming
The control panel immediately seizes the phone line to answer a remote programming call.
While programming is underway, the Trouble LED flashes. This also allows on-site PC
downloading. If the control panel already uses the phone line for a report communication, it
sounds the three-beep error tone. This function requires an access code with programming
authority (Level 1).
6.3
Keypads
6.3.1
Built-in keypad
The keypad built into the control/communicator is an alphanumeric LCD keypad. It has a two-
line by 16-character display to provide information on various control panel functions. Usually,
the first line shows the off-normal condition, while the second line describes specific details
that might be relevant to the existing system status. A built-in sounder annunciates keystroke
entries and acts as a warning device.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
41
Figure 6.1: Built-in Keypad
1 Green Power LED - is on when the AC
power is present, and flashes when
the unit is operating from battery
power.
9 [#/Enter] key - to accept data when in
the programming mode.
2 Yellow Trouble LED - lights when the
system detects a problem with wiring
or internal circuitry. The Trouble LED
flashes while programming mode is
active and whenever inputs are not
active, such as during smoke power
reset or alarm verification.
10 [History] key - to view system events.
3 Red Alarm LED - lights when the
system registers an alarm and was not
reset.
11 [Reset] key - briefly (programmable
from 1 to 16 seconds) turns off power
to the detectors to reset them and
clears any off- normal conditions.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
42
en | System Operation
Fire Alarm Control Panels
4 Yellow Silenced LED - lights when the
user manually silences an alarm
condition (fire or water flow), turns off
when the condition that was silenced
is corrected.
12 [Silence] key - mutes the bell or sirens
for an alarm condition, if the system is
so configured.
5 [Disable] key - used to disable or
re‑enable inputs, NACs or relays
(outputs), and the dialer.
13 [Drill] key – used to activate the NACs
manually. It creates a history log entry
and as an option reports to the central
station.
6 [Test] key - used to select one of seven
special test modes.1
14 Yellow Supervisory LED - lights
whenever the system registers a
supervisory condition.
7 [*/Back] key - used during
programming to exit from menus or to
exit from the programming mode
entirely.
15 Yellow GND Fault LED - lights
whenever the system detects a ground
fault condition.
8 [0/Prog] key – for selecting the
programming mode.
16 [Acknowledge] key to silence local
keypad sounders and to step through
the groups of off-normal conditions.
For abbreviations on the keypad and control panel, see Control Panel Display Descriptions,
100.
6.3.2
FMR-7033 keypad
The FMR-7033 Keypad is an alphanumeric LCD keypad. Up to four of these keypads can be
mounted apart from the main control panel to provide additional locations for system status
and control. The LCD display and keys operate identically to those of the built-in keypad on
the control panel.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
43
Figure 6.2: FMR-7033 Keypad
1 LEDs
3 Keys
2 Keypad Display
6.4
Testing
Select any of seven special test modes using the [Test] key on the built‑in and FMR‑7033
keypads.
6.4.1
Walk test
The Walk Test allows a technician to alarm each point manually to ensure that detectors
connected to a point send an Alarm report to the control panel. While in this mode, the LCD
shows the system test status and the trouble sounder sounds every 10 sec. NAC outputs
activate during this test as points are alarmed and restored based on the following settings:
–
–
–
SHORT ACTIVE:1 second activation
LONG ACTIVE:5 second activation
NO ACTIVE:outputs do not activate
As each point is alarmed, the outputs activate once (if selected) and power is reset. As each
point is activated, alarms and restorals are logged in the control panel’s history log. When the
point returns to standby, the outputs activate twice. The control panel attempts to reset
points ten times to restore them. Points remaining alarmed when exiting from the walk test
mode cause an immediate alarm.
6.4.2
Communicator test
The communicator sends a test report. While communication is in progress, the Power LED
flashes. When the communication succeeds, a long keypad beep sounds, the Power LED
returns to normal, and the display returns to normal.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
44
en | System Operation
Fire Alarm Control Panels
Notice!
This test is available only if your system sends alarms and system information to a monitoring
service, and was programmed by the security installing company to permit communicator
tests.
NOTICE!
Warning!
Reset upon termination of test
Terminating the communicator test function (with the [*/Back] key) resets the communicator
and discards all unsent reports. When an off-normal condition occurs during a Communicator
test, the test automatically resets, clearing all reports, so the off-normal conditions are sent
normally.
!
6.4.3
Battery/NAC circuits test
If a power failure occurs, your control panel has a built-in battery that continues to power the
system for several hours. The control panel automatically recharges the battery when power is
restored. In this test mode, the system operates the local NAC circuits and tests the battery
for two seconds. The test results are shown at the end of the test, and are not reported to the
central station. Pressing the [*/Back] key or the [#/Enter] key returns the display to standby
mode, or the unit times out after three minutes.
6.4.4
6.4.5
Activate ouputs test
This test turns a selected output on and off manually.
Zone input level test
This test shows the status of a selected on-board point. The loop existing through the point is
shown. Normal loops show 11 mA to 15 mA. Loops in alarm show over 25 mA, and loops in
trouble show less than 6 mA.
6.4.6
Addressable point test (MUX test)
This test allows activation of the special test mode for addressable (multiplex) devices. This
applies only if the optional D7039 Addressable Point Bus Expander module is installed. When
this test mode is selected, the system asks which bus to test, 1 or 2. Select 1 to test points 9
to 128 and select 2 to test points 129 to 255. The system presents 5 options:
1. List Devices: Shows the point numbers of all devices on the selected bus. Some devices
(such as a dual point module) can use two or more points
2. Show Holes: Lists locations on the bus that have no assigned device. This can help to find
programming errors or identify an available address for a new device.
3. Show Extras: The system scans the bus to identify devices that are present on the bus,
but are not programmed into the system. Scanning the bus takes about 60 sec. Restoring
the bus after scanning also takes about 60 sec. The system cannot identify devices above
Address 128 on Bus 1, or below Address 129 on Bus 2. If you know that a device is
connected to the system but cannot find it, ensure that it is connected to the correct bus:
9 to 128 for Bus 1, 129 to 255 for Bus 2.
4. Show Missing: Lists devices programmed into the system but not present on the bus are
listed. Unless a device was programmed into the system (such as using MUX EDIT), it is
not considered missing.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
45
5. Show Status: After you select a device and press [#/Enter], this test shows detailed
status information for the selected device. Eight conditions (not all status conditions
apply to or are supported by all devices) are shown. See the display shown below (which
updates automatically every five seconds). For this option, you can view the status of any
MUX device regardless of which bus you selected to test when test mode was entered.
– XxLxRxDxMxTxFxAx
x is either 0 or 1 depending on whether the condition is false or true (0=false and 1=true). The
letters indicate the condition:
–
–
X: Reserved for future use.
L: Commanded relay state - this is how the output relay should be set. R: Actual relay
state - this is how the output relay is actually set.
–
–
D: Detector dirty - the detector is excessively sensitive.
M: Missing device - the device cannot be found on the loop. Unless a device was
programmed into the system (such as using MUX EDIT), it is not considered missing.
T: Tamper – the detector’s case was opened.
–
–
F: Loop fault - the loop from a contact input device is open, or the device is faulted. A:
Loop alarm - the point is in alarm.
Pressing [*/Back] ends the display for any of these modes.
Examples: X0L0R0D0M0T0F0A0 (relay off, not dirty, not missing, no tamper, no fault and no
alarm).
6.4.7
Sensitivity test
Tests the MUX smoke detectors to determine if they are within their normal range of
sensitivity. Press [Test] then [9].
6.5
Point/Zone Mapping
The control panel supports a flexible system to map input points to output points. The system
defaults so that all NAC outputs are activated by a fire alarm. By programming output zones,
you can create almost any output activation scheme, such as “floor above and floor below”
activation or conditional elevator recall.
Input points: Smoke detectors, pull stations, and so on.
Zone: A group of input points (Zones 1 to 50 are configurable, 52 to 63 are activated
automatically).
Output points: NACs (notification appliance circuits) such as bells, strobes, and relays. Inputs
activate zones, and zones activate outputs.
Zones 1 to 50 are available for the installer to program. Each input can activate one zone;
however, any number of inputs can be mapped to the same zone.
Zones above 50 are automatically activated by inputs. For example, any input that is
configured as a waterflow type activates Zone 61 when it is alarmed. Any output driven by
Zone 61 activates when any waterflow type point is alarmed.
Up to 64 zones can be assigned. The installer can assign Zones 1 to 50. Zones 51 to 63 are
hard-coded to pre-assigned conditions.
For how inputs control zones and zones control outputs, see the following figure:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
46
en | System Operation
Fire Alarm Control Panels
Figure 6.3: Mapping inputs, zones, and outputs
1 Input Point 1 is assigned to Zone 1,
4 Input Point 4 is assigned to Zone 2,
mapped to NACs 1 and 2.
mapped to NAC Point 1.
2 Input Point 2 is assigned to Zone 2,
mapped to NACs 1 and 2.
5 Input Point 5 is assigned to Zone 3,
mapped to NAC 2, LR 1 and RR1.
3 Input Point 3 is assigned to Zone 2,
mapped to NACs 1 and 2.
6 General Alarm Zone 63 drives LR 2.
For pre-assigned zone assignments, see the following table:
Zone
51
Condition
Reserved for future use.
52
General Fire Alarm, Waterflow (non-silenceable). Same as Zone 53, but remains
active even while system is silenced.
53
54
General Fire Alarm (silenceable). Active when a fire alarm condition is present;
does not activate for waterflow.
Activates for approximately 7 sec before dialing, to initiate dial tone on a ground
start phone system.
55
56
57
General Supervisory (silenceable)
General Waterflow (silenceable)
Communication Trouble. Active when the dialer fails to communicate; remains
active until communication through the digital communicator is restored.
58
59
General Supervisory Alarm (non-silenceable). Active when any supervisory alarm
condition is present.
Alarm Verification. Active while alarm verification is in progress. This starts with
the first detection of an alarm to be verified and clears in two minutes, or when
system is reset.
60
No AC. Active when AC power fails.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
System Operation | en
47
Zone
Condition
61
62
General Waterflow (Non-silenceable). Active when any waterflow alarm is present.
General Trouble. Active while any system trouble is present, not active in test and
programming modes.
63
General Alarm, Waterflow (non-silenceable). Active while any alarm, including
supervisory, is present. Remains active even while system is silenced.
Table 6.3: Pre-assigned zones
6.6
Personal Identification Numbers (PINs)
The personal identification number (PIN) is the four digit code users enter at the keypad to
gain access to the system. A PIN can be assigned to each User Number. The User Number
identifies each person using the system. There are 16 possible User Numbers (00 to 15). User
codes 00 to 99 are available with the installation of a D7039 Multiple Expansion Module. The
Authority Level assigned to each User Number determines which functions each user can
perform.
Your system can have up to 100 different PINs, each four digits long. There is one PIN for each
User Number. Attempting to assign the same PIN to multiple User Numbers results in the
three-beep error tone, and the change is not made.
User Number 00 is designated as a Programmer’s Code. It can be used to silence alarms,
reset, disable, and program the unit.
User Number 00 is shipped from the factory with the sequence of 9876. Change this code to
one of your personal preference. It is automatically assigned the highest authority. Never
program PINs with common sequences such as 1111, 1234, or 2468 because they are easily
violated.
Authority levels are assigned to PINs to determine which functions each user can perform.
For a description of the four authority levels, see the following table:
PIN authority level Allowed operations
Maximum (1)
Medium (2)
Minimum (3)
None (0)
All control panel operations, including programming, and disable
System test modes, fire drill, reset, silence, view history
Silence, view history
None
Table 6.4: PIN authority levels
6.7
Communicator Operation
The FPD-7024 contains an integrated communicator that can be optionally enabled to send
reports to a monitoring station. When enabled, operation of the communicator is fully
automatic.
Notice!
You must enable and configure the communicator before it works. The communicator and
phone line monitors are disabled in the default factory configuration.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
48
en | System Operation
Fire Alarm Control Panels
Notice!
To disable a phone number, set the FORMAT to 0=disable. To completely disable the commu-
nicator, set FORMAT to 0=disable for both phone numbers, and set MONITOR to 0=NO for
both phone lines.
Notice!
Do not install this control panel on a phone line that might be required for other emergency
use.
When events occur, the communicator sends them to the monitoring station in priority order
according to NFPA requirements. Fire and waterflow alarms are sent first, followed by
supervisory alarms and trouble reports and then all other reports. Priority reporting can send
a Restoral report after several alarm reports in a situation where a point sends multiple
alarms, implying that a point is restored when it has returned to alarm. The following
sequence, (alarm, restore, alarm) is sent as (alarm, alarm, restore) when priority sorting is
applied.
Warning!
Event sorting can hide unrestored points
!
Priority sorting on events sent to a monitoring station can cause the message sequence to im-
ply that a point is restored when it is not.
The communicator can store 32 events while waiting for the monitoring station to accept the
events. If more than 32 reportable events occur before the monitoring station accepts events,
some event information is lost and a Data Lost report is sent to the central station.
The FPD‑7024’s communicator is equipped with a line seizure relay to prevent interference
with outgoing event reports. In a system where the fire communicator shares the phone line
with other equipment on the premises, the phone line might be unavailable to the other
equipment for up to 15 min has a fault with the central station acceptance of the event data.
Phone lines for fire control panels must not be shared with other equipment.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Programming | en
49
7
Programming
Danger!
Untested systems!
After any programming change, and especially after remote programming changes, completely
check the operation of the control panel. Hazards to life and property can result if the system
is not tested to detect possible improper programming.
DANGER!
Warning!
Improper system operation!
When programming the system, enter only valid types of information within the ranges speci-
fied in the programming table. Incorrect programming results in improper system operation.
When using built-in programming, invalid input values might not be rejected in every case. En-
sure that you enter only the intended values while programming to prevent improper system
operation.
!
7.1
Programming features
For UL864 programming requirements, see the following table:
Program feature or
option
Permitted in UL864
(Yes/No)
Possible settings
Settings permitted in
UL864
Auto Test Frequency
Yes
4 HOURS
12 HOURS
24 HOURS
7 DAYS
4 HOURS
12 HOURS
24 HOURS
28 DAYS
Program Relay
AC Fail Delay
Yes
Yes
Yes
Release on Trouble
Activate on Ground
Start
Release on Trouble
Wait for DC
Wait Delay Time
0‑24 HRS
Wait Delay Time
1‑3 HRS
Phone Line Monitor
for Each Line
No
Yes
Yes
Remote Programming Yes
(offsite)
PHONE #1
Phone #1
Phone #2
PHONE #2
COMPTR PHONE
Response Time
Yes
Fast (.5 sec)
Programmed
1 sec
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
50
en | Programming
Fire Alarm Control Panels
Program feature or
option
Permitted in UL864
(Yes/No)
Possible settings
Settings permitted in
UL864
NAC Config
Yes
Steady
Steady
Pulsing
Pulsing
California March
Temporal
Wheelock
Gentex
California March
Temporal
Wheelock
System Sensor
System Sensor
Alarm/Trouble Open
Status
Yes
Yes
1) Alarm
2) Trouble
2) Trouble
Latching
1) Yes
2) No
1) Yes for Alarms
Heartbeat Interval
Ring Count
Yes
Yes
Yes
001 - 255
00 - 15
001 - 090
00
PIN Required on
Remote Keypad
0) No
1) Yes
1) Yes
NAC Silence Mode
Yes
1) Audible only
2) Audi & Visi
1) Audible only
Table 7.1: Programming features for UL864
7.2
Point programming
Each of the points in the system can be programmed with its own characteristics. Point
functions simplify the programming of points by allowing you to define a common set of
characteristics for similar points, and assigning those characteristics to selected points as a
point function. There are 16 point functions, each of which has programmable features for
configuration (fire, waterflow, and so on), local only operation, silencing, and loop response.
Each point is assigned to use the characteristics of one point function, and then is individually
programmed for additional characteristics: response to an open circuit, enabled status, output
zone, verification, latching and point description.
Before programming the control panel, determine the types of functions that are needed, and
then map the various input points to the functions. For example, you might determine that you
have the following functions:
1 = Pull Station
2 = Smoke Detector
3 = Reset Keyswitch
4 = Silence Keyswitch
5 = Supervisory Input
6 = Local Test
7 = Waterflow Sensor
For the characteristics that correlate with each function, see the following table. For default
point function information, see Appendix D.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Programming | en
51
Function
Configuration
Local only?
Silenceable?
Loop response
1. Pull Station
Fire
Fire
No
No
No
No
Fast
Fast
2. Smoke
Detector
3. Reset
Reset
Yes
Yes
No
No
No
Yes
Fast
Fast
Fast
Keyswitch
4. Silence
Keyswitch
Silence
5. Supervisory
Input
Supervisory
6. Local Test
Fire
Yes
No
Yes
No
Fast
7. Waterflow
Sensor
Waterflow
Programmed
Table 7.2: Point function characteristics
7.3
Alpha programming
When programming the point descriptions, the numeric keys are used to enter alphanumeric
information similar to the way telephone keys are used to process information over the phone
lines each key represents four or more letters or symbols. For alphanumeric point
programming, see the following table:
Notice!
A different character is entered each time a numeric key is pressed. For example, pressing
[2/▲] repeatedly enters A, B, C, 2, A, B, and so on.
Key
Values
1
SPACE
1
,
‛
&
/
#
!
1
A
D
G
J
B
E
H
K
N
C
F
I
22
32
42
52
62
2
3
4
5
6
L
O
M
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
52
en | Programming
Fire Alarm Control Panels
Key
Values
P
T
R
U
X
Z
S
V
Y
0
72
82
92
7
8
W
Q
9
0
Prog
Enters the description and returns to the programming menu.
Returns to the programming menu without entering changes.
#
Enter
*
Back
Moves the cursor one space to the right.
Moves the cursor one space to the left.
Silence
Disable
1 Press [1] nine times to reach this value.
2 Press the listed key four times to reach this value.
Table 7.3: Programming points using alphanumics
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Programming | en
53
Figure 7.1: Essential keys for alpha programming
1 Number keys (including 0) - used to
4 [Disable] key - moves the cursor one
space to the left.
enter alphanumeric values.
2 [*/Back] key - used to exit alpha
programming, or exit the programming
mode entirely.
5 [Silence] key – moves the cursor one
space to the right.
3 [#/Enter] key - used to accept data
when in programming mode.
7.4
Format programming
4/2
When 4/2 Format is used, reports generated by points consist of an event type (first digit) and
a point number (second digit). Digits can be programmed for the following events: fire alarm,
fire restoral, waterflow alarm, supervisory alarm, point trouble, trouble restore, point disable,
disable restoral, and monitor alarm. The same event type (first digit) is sent for any point. The
point number is the second digit. Each point can be programmed to a different digit. This
programming is done under
7- PROG FORMATS, 1- 4/2 POINT RPT.
Additionally, 18 system events can each be programmed with a unique two-digit code. Events
that can be programmed this way include, for example: System Silence, Fire Drill,
Phone 1 Trouble, and Phone 2 Restoral. This programming is done under
7- PROG FORMATS, 2- 4/2 RPT CODS.
The 4/2 (and 3/1) format cannot report full point data for each point. Points 1 to 10 have
unique reporting codes. The codes repeat every ten points. For example, Point 31 has the
same point report as Points 11 and 21.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
54
en | Programming
Fire Alarm Control Panels
BFSK
Similar to the programming of system events for 4/2 formats, five system events can be
programmed for two unique digits each when the BFSK format is used. This programming is
done under
7- PROG FORMATS, 3- BFSK RPT CODS.
The BFSK format supports only a three-digit account number. The control panel sends the first
three digits that are programmed. The BFSK (and tone burst) format requires that an A (hex
character) be entered at the control panel to cause the receiver to display 0. The BFSK format
can report only eight points, so Points 8 to 255 are all reported as point “8”.
SIA
The SIA reports are fixed, and do not require programming.
Contact ID
The Contact ID reports are fixed and do not require programming.
3/1
The 3/1 reporting codes are determined by the programming of the 4/2 codes. Send only
Digit 1 (left digit of the two-digit code) and the first three digits of the account number.
Modem IIIa2
The Modem IIIa2 reports are fixed and do not require programming.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Programming | en
55
7.5
Program menu tree
Main Menu
Level 1
Level 3
Level 5
Level 4
Level 2
CMND/#
1-SYSTEM
1-PROG TIME
1-TEST TIME
2-TEST FREQ
2-AUTO TEST
1-DISABLE
2-ENABLE
3-DAYLIGHT SAV
TEST
1-PINS
2-AUTHORITY
1-PROGRAMR PIN
2-USER PINS
2-SECURITY
HISTORY
DISABLE
1-(reserved)
2-TIMERS
1-SMOKE RESET
2-AC FAIL DELAY
3-AUTO SILENCE
4-(reserved)
3-AC LINE SYNC
5-DISPLAY RATE
1-UPDATE BUS
2-SETUP KEYPDS
3-PROG SYSTEM
4-OPTION BUS
DRILL
5-PIN
1-LOCAL
2-REMOTE
REQUIRED?
6-NAC SIL
MODE
PROG/0
1-AUDIBLE ONLY
2-AUDI & VISI
7-REMOTE PGM
0-FUNCTION
1-ALARM/TROUBLE
2-OUTPUT ZONE
3-VERIFICATION
4-LATCHING
1-POINT
NUMBER
5-DESCRIPTION
<DRILL> NEXT PNT
<HIST> PREV PNT
0-CONFIGURE
1-LOCAL ONLY
2-(reserved)
1-FIRE
2-WATERFLOW
2-POINT
FUNCTION
3-SUPERVISORY
4-(reserved)
5-RESET
4-PROG INPUTS
3-SILENCEABLE
4-LOOP RESPONSE
5-(reserved)
6-SILENCE
7-AC FAULT
<DRILL> NEXT FCT
<HIST> PREV FCT
1-COPY FROM POINT
2-COPY TO FIRST POINT
3-COPY TO LAST POINT
3-POINT COPY
Figure 7.2: Program Menu
For factory defaults, see Appendix D.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
56
en | Programming
Fire Alarm Control Panels
Figure 7.3: Program Menu - continued
For factory defaults, see Appendix D.
7.6
Shortcuts
You can use shortcuts to reduce repetition and provide speedy instructions for programming
the control panel.
The first level in the system is the Main Menu. For all system programming, <PROG/0> is your
Main Menu choice. Therefore, the first number in the shortcut is “0”.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Programming | en
57
The second level in your system provides eight options: PROG TIME, SECURITY,
PROG SYSTEM, PROG INPUTS, PROG OUTPUTS, PROG ACCOUNTS, PROG FORMATS, and
HISTORY DEFAULTS. When the D7039 MUX Expander is installed, a ninth option appears:
PROGRAM MUX. The second number in the shortcut enters the Level 2 option and allows
access to Level 3.
Level 3 provides the third set of options that branch from Level 2. The third number in the
shortcut represents the option chosen in Level 3.
For an example of the shortcut to TEST FREQ and TEST TIME, see the following figure. The
sample of the Program Menu Tree shows that to get to TEST TIME and TEST FREQ, you must
go to PROG/0 in Level 1, PROG TIME in Level 2, and AUTO TEST in Level 3. The shortcut is
simply a list of the keys you press to get to the fourth level option. Once you enter the
shortcut, follow the procedural description that appears on the screen of the specific function
you are programming.
2
1
3
Shortcut = 012
LEVEL 1
(Main Menu)
LEVEL 2
LEVEL 3
LEVEL 4
1- SYSTEM
1- PROG TIME
1- TEST TIME
5
2- AUTO TEST
2- TEST FREQNCY
PROG/0
4
6
7
8
Figure 7.4: Example of a programming shortcut
1 Use "0" to select PROG from the Main
5 Password
Menu which scrolls at the System
Normal display.
2 Use "1" to select PROG TIME from
Sub-Level 2.
6 Second number in shortcut
7 Third number in shortcut
3 Use "2" to select AUTO TEST from Sub-
Level 3. Follow the procedural
description that appears on the
screen.
4 First number in shortcut
8 Fourth number in shortcut
7.7
Remote programming
The system operates during remote programming so that new alarms end the remote
programming session and report normally. Using the keypads to perform other functions
during remote programming (such as tests and disables) can cause remote programming to
disconnect or other unexpected operations. Avoid downloading programming changes that
cause alarms, because the session disconnects as soon as the alarm occurs, before the
session completes. To indicate that the system is in a special operating mode with user input
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
58
en | Programming
Fire Alarm Control Panels
inhibited (but alarm monitoring continuing), the system indicates SYSTEM TROUBLE,
RMT PRG ACTIVE during remote programming. Sounders do not activate during this mode, but
other outputs programmed for Zone 62, general system trouble, do activate.
Trouble conditions that occur during a remote programming session are not annunciated at
the control panel until the remote programming session ends. These conditions are available
in the remote programmer diagnostic displays during the session. Alarm conditions terminate
remote programming and are shown immediately.
When remote programming is disabled, you can still connect to the control panel for
diagnostics and view the existing programming (except PIN numbers). To actually change
programming, enable remote programming.
To enable remote programming, refer to the following programming items:
–
0-3-7 Remote Programming, 67
0-6-1 Computer PH/IP, 78
0-6-1 Account Number 1, 78
0-6-2 Dialing Type, 82
–
–
–
–
–
0-6-4 Ring Count, 84
0-6-6 Machine Bypass, 85
An access code with maximum authority (1) is needed to begin remote programming from the
panel.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
59
8
Control Panel Programming
Main Menu:
SYSTEM NORMAL
SELECT: PROG/0
SELECT: ENTER/#
SELECT: TEST
SELECT: HISTORY
SELECT: DISABLE
SELECT: DRILL
Programming Menu:
PROG/0
1-PROG TIME
2-SECURITY
3-PROG SYSTEM
4-PROG INPUTS
5-PROG OUTPUTS
6-PROG ACC’NTS
7-PROG FORMATS
8-HISTORY DEFLTS
9-PROGRAM MUX
8.1
PROG TIME
PROG TIME
1-SYSTEM
2-AUTO TEST
3-DAYLIGHT SAV
8.1.1
Program time
Shortcut: 0-PROG, 1-PROG TIME, 1-SYSTEM
The following window appears:
ENTER DATEMMDDYY: _______
Enter the date followed by the [#/Enter] key. The following window appears:
ENTER TIMEHHMM: _______
Enter the time followed by the [#/Enter] key.
8.1.2
Automatic test
Test Time
Shortcut: 0-PROG, 1-PROG TIME, 2-AUTO TEST
Use this feature to program the time of day at which automatic tests occur. This feature uses a
24‑hour clock (for example, 11:00 p.m. = 2300).
The following window appears:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
60
en | Control Panel Programming
Fire Alarm Control Panels
AUTOMATIC TEST
1-TEST TIME
2-TEST FREQNCY
Press [1] to select Test Time. The following window appears:
AUTO TEST TIMEHHMM: _______
Enter the time followed by the [#/Enter] key.
Test Frequency
Shortcut: 0-PROG, 1-PROG TIME, 2-AUTO TEST
This feature allows you to program how often the automatic test reports are sent. The first
test is sent when the programmed test time matches the system time. Subsequent reports are
sent according to the selected interval.
The following window appears:
AUTOMATIC TEST
1-TEST TIME
2-TEST FREQNCY
Press [2] to select Test Frequency.
The following window appears:
AUTO FRQNCY ( )
1-4 HOURS
2-12 HOURS
3-24 HOURS
4-7 DAYS*
5-28 DAYS*
* For acceptable programming selections for UL864 9th edition Listed applications, see
Press the number key that corresponds to your selection. The existing setting is displayed in
parentheses on the first line. After you have programmed the test frequency, the previous
window appears.
8.1.3
Daylight saving time
Shortcut: 0-PROG, 1-PROG TIME, 3-DAYLIGHT SAV
This feature enables automatic adjustment of system time for Daylight Saving Time. The dates
for the adjustment are pre-programmed in the system.
The following window appears:
DAYLIGHT SAV
1-DISABLE
2-ENABLE
Press [1] to select DISABLE or [2] to select ENABLE. After you have programmed this feature,
the previous window appears.
8.2
SECURITY
SECURITY
1-PINS
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
61
2-AUTHORITY
8.2.1
Personal Identification Numbers (PINs)
Programmer PIN
Shortcut: 0-PROG, 2-SECURITY, 1-PINS
The Programmer PIN is the code used by the installer to configure and operate the panel.
Factory default code is 9876 and may be changed at any time.
The following window appears:
PROGRAM PINS
1-PROGRAMR PIN
2-USER PINS
Press [1] for Programmer PIN. The following window appears:
USER 0
ENTER PIN:_______
Enter the PIN and press [#/Enter]. After you have programmed the Programmer PIN, the
previous window appears.
Program User PINs
Shortcut: 0-PROG, 2-SECURITY, 1-PINS
Up to 15 additional user codes (or up to 99 additional users when the D7039 is installed) can
be programmed to protect the system from unauthorized operation and allow a record to be
kept of actions by individual system users.
The following window appears:
PROGRAM PINS
1 - PROGRAMR PIN
2 - USER PINS
Press [2] for user PINs. The following window appears:
OTHER PINS
USER (01-15)
Enter the user for whom you want to program a PIN and press [#/Enter]. Example: For User 5,
press [5]. The following window appears:
USER 5
ENTER PIN:_______
Enter the PIN and press [#/Enter]. After you have programmed the user PIN, the previous
window appears.
8.2.2
Authority
Shortcut: 0-PROG, 2-SECURITY, 2-AUTHORITY
This feature determines which system actions a user can perform.
For PIN authority levels, see the following table:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
62
en | Control Panel Programming
Fire Alarm Control Panels
PIN Authority Level
Allowed Operations
Maximum (1)
All control panel operations, including
programming and disable.
Medium (2)
System test modes, fire drill, reset, silence,
view history.
Minimum (3)
None (0)
Silence, view history.
None.
Table 8.1: PIN authority levels
The following window appears:
AUTHORITY
USER (01 - 15)
Enter the user for whom you want to program the authority level and press [#/Enter]. The
following window appears and scrolls through the following choices:
USER 1 ATHRY (_______ )
0- NONE
1- MAXIMUM
2- MEDIUM
3- MINIMUM
Press the number key that corresponds to your selection. The existing setting is shown in
parentheses on the first line. After you have programmed the user authority, the previous
window appears.
8.3
PROG SYSTEM
PROG SYSTEM
1 - (reserved)
2 - TIMERS
3 - AC LINE SYNC
4 - OPTION BUS
5 - PIN REQURED?
6 – NAC SIL MODE
7 - REMOTE PGM
8.3.1
Program timers
Shortcut: 0-PROG, 3-PROG SYSTEM, 2-TIMERS
The following window appears:
TIMERS
1 - SMOKE RESET
2 - AC FAIL DLY
3 - AUTO SILENCE
4 - (reserved)
5 - DISPLAY RATE
Smoke reset
Shortcut: 0-PROG, 3-PROG SYSTEM, 2-TIMERS
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
63
This feature determines how long the smoke detector power is off after reset. No alarms are
registered by the system for 5 sec after power is returned.
The display scrolls through the TIMERS options. Press [1] for Smoke Reset. The following
window appears:
SMOKE RESET (__ )
(1-16 SECS):_______
Enter the time and press [#/Enter]. The existing setting is shown in parentheses on the first
line. After you have programmed the smoke reset, the previous window appears.
AC fail delay
Shortcut: 0-PROG, 3-PROG SYSTEM, 2-TIMERS
This feature sets the number of hours the control panel waits after an AC failure before
sending an AC Failure report. A setting of DC causes the system to send a report when 25% of
the battery capacity is used.
The display scrolls through the TIMERS options. Press [2] for AC FAIL DELAY. The following
window appears:
AC FAIL DELAY
1 - WAIT FOR DC
2 - ENTER TIME
The wait for DC function causes the AC fail report to be sent when the battery is 25%
depleted, based on the measured voltage of the battery. If you want to WAIT FOR DC (25
percent of capacity), press [1]. The existing setting is displayed in parentheses on the first
line, either “DC”, or the number of hours selected. After you program the AC Fail Delay, the
previous window appears.
To ENTER TIME press [2]. The following window appears:
AC FAIL DLY (___)
(00-24 HRS):_______*
* For acceptable programming selections for UL864 9th edition Listed applications, see
Enter the time and press [#/Enter]. The existing setting is shown in parentheses on the first
line. After you program the AC Fail Delay, the previous window appears.
Notice!
When Wait For DC is the existing selection, the Enter Time menu displays DC as the time in
hours.
Auto silence
Shortcut: 0-PROG, 3-PROG SYSTEM, 2-TIMERS
This feature silences the sounding of an alarm condition on selected NACs after a certain
amount of time. When you use Auto Silence, pressing [0/Prog] disables the feature and the
only way to turn off an alarm is to manually silence it. Entering between 5 min and 99 min
means that the alarm sounds for that much time before automatically silencing.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
64
en | Control Panel Programming
Fire Alarm Control Panels
Notice!
If the condition that caused and alarm is not corrected after an alarm is silenced (automatical-
ly or manually), the alarm sounds again after 24 hours. The system must eventually be reset
after silencing to allow the alarmed zones to restore and detect new alarms.
The display scrolls through the TIMERS options. Press [3] for AUTO SILENCE. The following
window appears:
AUTO SILENCE (__)
(0, 5-99 min):_______
Enter desired length of time (or press [0/Prog] to disable) and press [#/Enter]. The existing
setting is shown in parentheses on the first line. After you program the auto silence, the
previous window appears.
Display rate
Shortcut: 0-PROG, 3-PROG SYSTEM, 2-TIMERS
Set the speed at which menus are displayed on the LCD (in units of 0.25 sec).
The display scrolls through the TIMERS options. Press [5] for DISPLAY RATE. The following
window appears:
DSPLY RATE (__)
.25 X (1-16):_______
Enter desired value and press [#/Enter]. The existing setting is shown in parentheses on the
first line. After you program the display rate, the previous window appears.
8.3.2
AC line synch
Shortcut: 0-PROG, 3-PROG SYSTEM, 3-AC LINE SYNC
When AC power is available, the control panel uses the line frequency to stabilize the real-
time clock. This setting must match the frequency of the local AC power (60 Hz in the US).
The following window appears:
AC LINE SYN (__)
1 - 50 Hz
2 - 60 Hz
Press the number key that corresponds to your selection and press [#/Enter]. The existing
setting is shown in parentheses on the first line. After you program AC Line Synch, the
previous window appears.
8.3.3
Option bus
Update bus
Shortcut: 0-PROG, 3-PROG SYSTEM, 4-OPTION BUS
When devices are added or removed from the option buses, this feature queries both option
buses and updates the list of connected devices. This enables the new devices and removes
supervision for devices no longer present.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
65
Warning!
Inoperable, unsupervised devices!
Be sure the count of devices displayed when this operation completes matches the number of
devices installed on both buses. Devices not detected during the update bus operation will
not operate and will not be supervised.
!
Notice!
These menu items are allowed only at the local keypad.
The following window appears:
OPTION BUS (M/M)
1 - UPDATE BUS
2 - SETUP KEYPDS
Press [1] to program the system to update the bus. After you program Update Bus, the
following window appears:
UPDATE COMPLETE
TOT BUS DEVS: X
Then the previous window appears.
Setup keypads
Shortcut: 0-PROG, 3-PROG SYSTEM, 4-OPTION BUS
This feature tells the system how many keypads to supervise. It automatically performs an
update bus operation as it completes.
OPTION BUS
1 - UPDATE BUS
2 - SETUP KEYPDS
Press [2] to set up keypads. The following window appears:
# OF KEYPADS (__)
(0-4):_______
Enter the desired value and press [#/Enter]. The existing setting is shown in parentheses on
the first line. After you set up the keypads, the update bus operation proceeds, then the
previous window appears.
8.3.4
PIN required
Local
Shortcut: 0-PROG, 3-PROG SYSTEM, 5-PIN REQUIRED?
A PIN can be required before performing operations. Enter the PIN at the local or built-in
keypad.
The following window appears:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
66
en | Control Panel Programming
Fire Alarm Control Panels
PIN REQUIRED?
1- LOCAL
2- REMOTE
Press [1] to require a PIN at the local keypad. The following window appears:
LOCAL KEYPD PIN?
_______: YES(1) NO(0)
Press the number key that corresponds to your selection. The existing setting is shown in
front of the colon on the second line. After making your selection, the previous window
appears.
Remote
Shortcut: 0-PROG, 3-PROG SYSTEM, 5-PIN REQUIRED?
The following window appears:
PIN REQUIRED?
1- LOCAL
2- REMOTE
Press [2] to select remote PIN. The following window appears:
REMOTE KYPD PIN?
_______: YES (1) NO (0)
Press the number key that corresponds to your selection and press [#/Enter]. The existing
setting is shown in front of the colon on the second line. After you select the PIN requirement,
the previous window appears.
For acceptable programming selections for UL864 9th edition Listed applications, see
Notice!
A PIN can be required before operations can be performed using the remote keypads on the
option bus. If the remote keypads are not otherwise secured, this option must be set to YES
to comply with NFPA and Local requirements.
8.3.5
NAC silence mode
Shortcut: 0-PROG, 3-PROG SYSTEM, 6-NAC SIL MODE
NAC silence mode allows notification devices to be silenced from the control panel. Any
output configured as silenceable is silenced upon silence operation. You can define audible
only or audible and visible by this option. If silenced, a relay is completely turned off.
The following window appears:
1-AUDIBLE ONLY
2-AUDI & VISI
Press [1] to configure the audible output to be silenceable leaving the visible output to
display. Press [2] to configure both the audible and visible outputs to be silenceable.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
67
8.3.6
Remote programming
Shortcut: 0-PROG, 3-PROG SYSTEM, 7-REMOTE PGM
Remote programming allows the panel to be called from a remote site by phone to reconfigure
any of the programmable options. When remote programming is disabled, you can still
connect to the control panel for diagnostics and to view the existing program. PIN numbers
are suppressed while remote programming is disabled.
REMOTE PGM
0- DISABLE
1- ENABLE
Press [0/Prog] to select DISABLE or [1] to select ENABLE, and the previous window appears.
Danger!
After any programming change, and especially after remote program changes, completely
check operation of the control units. Hazards to life and property can result if the system is
not tested for incorrect programming.
8.4
PROG INPUTS
PROG INPUTS
1- POINT NUMBER
2- POINT FUNCT
3- POINT COPY
Notice!
Point functions allow quick programming of similarly functioning points (for example, pull sta-
tions, smoke detectors) with common settings.
8.4.1
Point number
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
POINT NUMBER (1-255):_____
Enter the point number you wish to program and press [#/Enter]. Once you have entered the
point number, the display scrolls through the following PROG INPUT options:
PROG POINT
0- FUNCTION
1- ALARM/TROUBL
2- OUTPUT ZONE
3- VERIFICATION
4- LATCHING
5- DESCRIPTION
<DRILL> NEXT PNT
<HIST> PREV PNT
Press the number key that corresponds to your selection.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
68
en | Control Panel Programming
Fire Alarm Control Panels
Pressing [Drill] retrieves the next point. For instance, if you are programming Point 2 and you
press [Drill], you retrieve the setting for Point 3.
Pressing [History] retrieves the previous point. For instance, if you are programming Point 2
and you press [History], you return to the setting for Point 1.
Assigning point functions
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
This feature assigns each point to one point function. A point function is a set of
characteristics that you can assign to selected points. There are 16 point functions to choose
from.
assigning points to point functions that were programmed with a response time other than
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG INPUT options.
Press [0/Prog] to select FUNCTION. The following window appears:
POINT FUNC. (___)
(01 - 16):_______
Enter the function number you wish to assign to the point and press [#/Enter]. The existing
setting is shown in parentheses on the first line. After you assign a point function, the previous
window appears.
Alarm/Trouble status
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
This feature allows you to program the system response to an open loop condition. A shorted
loop always causes an alarm condition.
For acceptable programming selections for UL864 9th edition Listed applications, see
ALARM: A point in an open circuit state causes an alarm.
TROUBLE: If a point is in an open circuit state, the system responds with a trouble condition.
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG INPUT options.
Press [1] to select ALARM/TROUBLE. The following window appears:
OPEN STATUS (__)
1- ALARM
2- TROUBLE
Press [1] to select ALARM on open loop and ALARM on shorted loop or [2] to select TROUBLE
on open loop and ALARM on shorted loop. The previous window appears. The existing setting
is shown in parentheses on the first line.
Output zones
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG INPUT options.
Press [2] to select OUTPUT ZONE. The following window appears:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
69
OUTPUT ZONE ZZZ
(01 - 50):_______
Press the number key that corresponds to your selection. ZZZ indicates the point being
programmed. The existing setting is shown on the second line. After you set up the output
zone, the previous window appears.
Verification
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
This feature resets the detector once to determine if the alarm recurs before annunciating or
sending a signal. The total delay introduced by this feature is equal to the smoke power reset
time plus five seconds. Alarm verification cannot be selected for points that are configured as
WATERFLOW or SUPERVISORY types.
Enter the point number you wish to verify and press [#/Enter]. The display scrolls through the
PROG INPUT options.
Press [3] to select VERIFICATION. The following window appears:
ALARM VERIF (ZZZ)
_______: YES(1) NO(0)
ZZZ indicates the point being programmed. The existing setting is shown on the second line.
Press either [1] to verify or [0/Prog] to not verify. The previous window appears.
Latching
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
If a zone is non-latching, the system resets the alarm status automatically (but does not reset
smoke power) when the input restores to the standby condition. Otherwise, the system must
be manually reset.
For acceptable programming selections for UL864 9th edition Listed applications, see
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG INPUT options.
Press [4/◄] to select LATCHING. The following window appears:
LATCHING? ZZZ
:YES(1)NO(0)
ZZZ indicates the point being programmed. The existing setting is shown on the second line.
Press the number key that corresponds to your selection. Select YES for alarm.
The previous window appears.
Point description
Shortcut: 0-PROG, 4-PROG INPUTS, 1-POINT NUMBER
For this feature, use the numeric keys to enter alphanumeric information to identify each input
(such as initiating circuit). The system allows one 16-character description per input. Enter the
point number you wish to program and press [#/Enter]. The display scrolls through the PROG
INPUT options.
Press [5] to select DESCRIPTION. The following window appears:
PNT DSCRPTN ZZZ:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
70
en | Control Panel Programming
Fire Alarm Control Panels
Enter the description using the numeric, [Silence] and [History] keys, then press [#/Enter] to
save the description.
8.4.2
Point function
Shortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION
There are 16 point functions, each of which has programmable features for: configuration
(fire, waterflow, and so on), local only operation, silencing, and loop response.
Notice!
At default, points 9 to 255 are programmed as Function 10 which is set as Fire. Function 11 is
set as Supervisory. Function 04 is set as Waterflow 16 second.
The following window appears:
POINT FUNC. (__)
(01 - 16):_______
Enter the function number you wish to program and press [#/Enter]. The following window
appears:
PROG FUNCT
0- CONFIGURE
1- LOCAL ONLY
2- (reserved)
3- SILENCABLE
4- LOOP RESPONS
5- (reserved)
<DRILL> NXT FCT
<HIST> PREV FCT
Enter the function you wish to program.
Configure
Shortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION
–
–
Fire: When activated, the point shows FIRE ALARM on control panel and keypads,
activates selected output devices, and sends a Fire Alarm report (if programmed). Fire
points are defaulted to a latch when first configured.
Waterflow: When activated, the point shows WATERFLOW ALARM on control panel and
keypads, activates selected output devices, and sends a Waterflow Alarm report (if
programmed). Waterflow points are defaulted to a non-verify characteristic when first
configured.
–
Supervisory: When activated, the point shows SUPERVISORY ALARM on control panel
and keypads, and sends a Supervisory Alarm report (if programmed). Supervisory points
are defaulted to a non-verify characteristic when first configured.
–
–
Reset: When activated, the point initiates a control panel-reset operation to clear alarms
and reset smoke detectors. Only points 1 to 8 can be configured as reset points.
Silence: When activated, the point initiates a control panel silence operation to turn off
sounders if the control panel is configured to allow silencing. Only points 1 to 8 can be
configured as silence points.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
–
Control Panel Programming | en
71
AC Fault: When activating, the control panel waits for the AC Delay Timer to expire
before indicating or sending a trouble condition. When the timer expires, it shows an AC
Fault on the control panel and the trouble LED turns on.
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG FUNCTION options.
Press [0/Prog] to select CONFIGURE. The following window appears:
ACTVTN TYPE ( )
1- FIRE
2- WATERFLOW
3-SUPERVISORY
4- (reserved)
5- RESET
6- SILENCE
7- AC FAULT
Press the number key that corresponds to your selection. (The existing setting is shown in
parentheses on the first line.) The previous window appears.
Local only
Shortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION
Enabling this feature provides the input point for local annunciation only, with no
communicator report. Enter the point number you wish to program and press [#/Enter]. The
display scrolls through the PROG FUNCTION options.
Press [1] to select LOCAL ONLY. The following window appears:
LOCAL ONLY
_______: YES (1)NO(0)
Press either [1] to enable or [0/Prog] to disable. The previous window appears.
Silencing
Shortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION
This feature determines if an output zone (1 to 50) follows the Silence button (relays reset,
NACs silence).
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG FUNCTION options.
Press [3] to select SILENCEABLE. The following window appears:
SILENCABLE? (FF)
_______: YES (1)NO(0)
Press [1] for relays to reset and NACs to silence when the Silence button is pressed, or press
[0/Prog] for relays to remain latched until reset and NACs to continue sounding when the
Silence button is pressed.
Notice!
When an output is assigned to more than one zone, the programming of the zone that triggers
the output controls the output. When more than one zone triggers the output, if one of the
zones is programmed as non-silencing, the output will be non-silencing.
NOTICE!
The previous window appears. FF indicates the function being programmed.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
72
en | Control Panel Programming
Fire Alarm Control Panels
Loop response
Shortcut: 0-PROG, 4-PROG INPUTS, 2-POINT FUNCTION
This feature allows you to configure points to activate with standard response time (setting 1)
or one system-wide programmed response time (setting 2).
Enter the point number you wish to program and press [#/Enter]. The display scrolls through
the PROG FUNCTION options.
Press [4/<] to select LOOP RESPONSE. The following window appears:
RESPNS TIME (___)
1- FAST (.5 sec)
2- PRGRMMD*
* For acceptable programming selections for UL864 9th edition Listed applications, see the
Press the number key that corresponds to your selection (the existing setting is displayed in
parentheses on the first line). The previous window appears.
When you select a programmed response time, the system asks you to enter a response time
from 1 sec to 89 sec that applies to all functions. All functions share a single programmable
response time setting. If this time is set for multiple functions, the last time set is used.
When set for fast response operation, multiplex points typically have a response time.
Response time is (the maximum time an input must be held to guarantee an alarm) of
approximately 1 sec. Response time increases as points on the bus remain off-normal (in
alarm or with a loop or detector trouble), to a maximum of 20 sec in the extreme case of all
points on the bus being in trouble and one point in alarm. On a fully loaded system with only a
few points in alarm or trouble, fast response time remains at approximately 1 sec. For
programmed response, the response time tolerance is ±3 sec when only a few points are off-
normal, and increases by up to 20 sec when all points are off-normal.
On-board points have a response time tolerance of ±1 sec for programmed response time, and
+0.5 sec or - 0.25 sec for fast response time.
Notice!
Up to 20 points can be assigned to point functions that were programmed with a response
time other than Fast. If more than 20 points are assigned to functions programmed with a re-
sponse time other than Fast, an error message appears: MAX PROGRAMD POINTS EXCEE-
DED. Switching a point function from Fast to Programmed can cause this error, depending on
how many points reference the point function.
<DRILL> NEXT FCT: Pressing [Drill] retrieves the next function. For instance, if you are
programming Point Function 2 and you press [Drill], you retrieve the setting for Point
Function 3.
<HIST> PREV FCT: Pressing [History] returns you to the previous function. For instance, if you
are programming Point Function 2 and you press [History], you return to the setting for Point
Function 1.
8.4.3
Point copy
Shortcut: 0-PROG, 4-PROG INPUTS, 3-POINT COPY
Point copy allows you to copy the settings you entered for one point to one or more other
points.
The following window appears:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
73
COPY FROM
POINT:_______
Enter the point you wish to copy from and press [#/Enter]. COPY TO FIRST POINT:_______
Enter the first point you wish to copy to and press [#/Enter]. COPY TO LAST POINT:_______
Enter the last point you wish to copy to and press [#/Enter]. The PROG INPUTS menu appears.
This feature does not copy the description. Point copy is intended for use only on input
points. Do not copy from an output point (future use), or copy over a programmed output
point. The copy operation automatically stops, with an error message, if outputs are
encountered. While copying to a large number of points, the remote keypads might briefly
show system fault, because the keypads are not updated during the copy operation.
8.5
PROG OUTPUTS
PROG OUTPUTS
1- NACs
2- RELAYS
8.5.1
Programming NACs
Shortcut: 0-PROG, 5-PROG OUTPUTS, 1-NACs
The main control panel includes two local NACs (NAC 1 and NAC 2). The FPD‑7024 can also
support up to four FPP‑RNAC‑8A‑4C Remote NAC Power Supplies, which offers a total of 16
remote NACs (four NACs per RNAC).
The following window appears:
NAC OUTPUTS
1- LOCAL
2- REMOTE 1
3- REMOTE 2
4- REMOTE 3
5- REMOTE 4
Press the number key that corresponds to your selection.
Local NACs
Shortcut: 0-PROG, 5-PROG OUTPUTS, 1-NACs
The display scrolls through the NAC options. Press [1] for LOCAL. The following window
appears:
ONBOARD NAC
1- NAC #1
2- NAC #2
Press the number key that corresponds to your selection. The display scrolls through the
following selection:
PROG NAC
1- AUTO SILENCE
2- CONFIGRATION
3- ZONE ASSIGNS
Press the number key that corresponds to your selection.
If you select [2] from the PROG NACs menu, the following selections scroll:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
74
en | Control Panel Programming
Fire Alarm Control Panels
NAC CONFIG ( )
1- STEADY
2- PULSING
3- CALIFORNIA MARCH
4- TEMPORAL
5- WHEELOCK
6- GENTEX
7- SYSTEM SENSOR
For acceptable programming selections for UL864 9th edition Listed applications, see
These selections control the pattern (code) for the selected NAC. Press the number key that
corresponds with the desired pattern:
–
–
–
–
Steady: Output turns on and stays on while the NAC is active.
Pulsing: Output turns on for 0.5 sec and off for 0.5 sec.
California March: Output turns on for 0.25 sec and off for 0.25 sec.
Temporal: Output turns on and off to implement the ANSI standard evacuation pattern
(Temporal code 3).
–
Wheelock: Output is configured to support Wheelock devices with synchronization
capability, including the ability to silence the horn of a combination horn strobe. The
Wheelock configuration is not supported by remote NACs implemented using a Remote
NAC power supply.
–
Gentex: Output is configured to support Gentex devices with synchronization capability,
including the ability to silence the horn of a horn strobe combination.
Notice!
The Gentex option does not synchronize to the UL864 9th Edition standard.
–
System Sensor: Output is configured to support System Sensor devices with
synchronization capability, including the ability to silence the horn of a horn strobe
combination.
After you program the desired pattern configuration, the previous window appears.
If you select 3 from the PROG NACs menu, you are asked to enter four zones to activate this
output.
OUTPUT ZONE A (XX)
(00-63):
Notice!
XX” indicates the existing setting for each of the four output zone settings.
Enter the desired zone to activate this output and press [#/Enter]. You are asked to enter up
to four zones (A, B, C, D). Enter 00 (or leave it set at “00”) for any unused zones to prevent
unintentional output activation. After all four zones are programmed, the previous window
appears.
For a list of pre-assigned zones, see the following table:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
75
Zone Pre-Assigned Condition
52
General Fire Alarm (non-silencing)
General Fire Alarm, (silencing)
Ground Start
53
54
55
56
57
58
59
60
61
62
63
General Supervisory, (silencing)
General Waterflow, (silencing)
Communication Trouble
General Supervisory Alarm (non-silencing)
Alarm Verification
AC Failed
General Waterflow Alarm (non-silencing)
General Trouble
General Alarm, Waterflow Supervisory (non-silencing)
Table 8.2: Pre-assigned zone quick reference
Remote NACs
Shortcut: 0-PROG, 5-PROG OUTPUTS, 1-NACs
Use only with the FPP‑RNAC‑8A‑4C. The display scrolls through the NAC options. Press [2]
for REMOTE 1, [3] for REMOTE 2, [4] for REMOTE 3, or [5] for REMOTE 4. One of the
following windows appears:
REM EXP NAC #1
1 - NAC #1
REM EXP NAC #2
1 - NAC #1
REM EXP NAC #3
1 - NAC #1
REM EXP NAC #4
1 - NAC #1
2 - NAC #2
or 2 - NAC #2
or 2 - NAC #2
or 2 - NAC #2
3 - NAC #3
3 - NAC #3
4 – NAC #4
3 - NAC #3
4 - NAC #4
3 - NAC #3
4 - NAC #4
4 - NAC #4
Press the number key that corresponds with the NAC you want to program. The display scrolls
through the following selections:
PROG NACs
1- (reserved)
2- CONFIGURATION
3- ZONE ASSIGNS
The options for remote NACs are the same as for local NACs.
Output Configuration:
Steady: Programmed to turn on steadily for a fire alarm.
Pulsing: Programmed to pulse for a fire alarm at 0.5 sec on and 0.5 sec off.
California March: Output turns on for 0.25 sec and off for 0.25 sec.
Temporal: Programmed to pulse for a fire alarm in Temporal 3.
Zone Assignment: Assign each output up to four zones. ZONE A, B, C, or D (00 = disabled) (1
to 63).
Press the number key that corresponds to your selection. After you program the local NACs,
the previous window appears.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
76
en | Control Panel Programming
Fire Alarm Control Panels
8.5.2
Programming relays
Shortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS
The main control panel includes three on-board relays (Relay 1, Relay 2, and Relay 3). The
FPD‑7024 can also support up to two D7035 Octal Relay Modules (Remote Relay 1 and
Remote Relay 2), that offer a total of 16 remote relays (eight relays per module).The following
window appears:
RELAY OUTPUTS
1- LOCAL
2- REMOTE 1
3- REMOTE 2
4- MULTIPLEX
Press the number key that corresponds to your selection.
Notice!
The option for multiplex relay programming is visible only if the D7039 Multiplex Expander is
installed.
Local Relays
Shortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS
The display scrolls through the Relay options.
Press [1] for LOCAL. The following window appears:
ONBOARD RELAY
(1-3):
Enter the number corresponding to the relay to be programmed and press [#/Enter]. The
display asks you to enter four zones to activate this output:
OUTPUT ZONE A:_______
(00 - 63):_______
Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similar
display for Zones B, C and D will appear to allow up to four zones to be assigned to this
output. When all four zones are assigned, the previous window appears.
An output point cannot be assigned to more than four zones. Each output does not need to be
assigned to four zones. Each zone can have any number of outputs assigned to it.
Remote relays
Shortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS
The display scrolls through the Relay options. Press [2] for REMOTE 1 or [3] for REMOTE 2.
The following window appears:
REMOTE RELAY @ x
(1 - 8):
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
77
Notice!
The @ x shows the address of the relay module in the system. The lower number address is
Relay 1; the higher one is Relay 2.When you address a MUX Module, you assign an address. If
you have a dual point, it would have two consecutive addresses.
Enter the relay you wish to assign and press [#/Enter]. The display shows:
OUTPUT ZONE A:_______
(00-63):_______
Enter the output number (00 to 63) you want to assign to Zone A and press [#/Enter]. A
similar display for Zone B appears. When all four zones are assigned, the previous window
appears.
An output point cannot be assigned to more than four zones. Each output does not need to be
assigned to four zones. Each zone can have any number of outputs assigned to it.
Multiplex relays
Shortcut: 0-PROG, 5-PROG OUTPUTS, 2-RELAYS
Warning!
!
Do not use this menu to program addresses configured as inputs.
The display scrolls through the Relay options. Press [4/◄] for MULTIPLEX. The following
window appears:
MUX OUTPUT
(009 - 255):
Enter the number corresponding with the output to be programmed and press [#/Enter]. The
output number of a multiplex relay is the second point of an I/O module. Adding 1 to the
address of the I/O module gives the address of the relay in the module. When the relay is
selected, the display asks you to enter four zones to activate this output:
OUTPUT ZONE A:_______
(00 - 63):_______
Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similar
display for Zone B, C and D appears, allowing up to four zones be assigned to this input. When
all four zones are assigned, the previous window appears.
An output point cannot be assigned to more than four zones. Each output does not need to be
assigned to four zones. Each zone can have any number of outputs assigned to it.
8.6
PROG ACCOUNTS
PROG ACC’NTS
1- PHONE / IP NUMS
2- PHON CONTROL
3- RPT STEERING
4- RING COUNT
5- COMM. TRIES
6- MACH. BYPASS
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
78
en | Control Panel Programming
7- ALT.COMM
Fire Alarm Control Panels
8.6.1
Phone Numbers/IP Addresses
Shortcut: 0-PROG, 6-PROG ACC’NTS, 1-PHONE/IP NUMS
The system can be programmed with two reporting phone numbers or IP addresses. Phone/
IP #1 is used with Account Number 1; Phone/IP #2 is used with Account Number 2. Remote
programming occurs on Line 1 using Phone/IP #3.
–
–
–
PHONE/IP #1: Phone Number 1 or IP address 1
PHONE/IP #2: Phone Number 2 or IP address 2
COMPTR PHONE: Sets the Phone Number or IP Address to call for remote programming.
For acceptable programming selections for UL864 9th edition Listed applications, see
The following window appears:
PHONE /IP NUMBER
1- PHONE /IP #1
2- PHONE /IP #2
3- COMPTR PH/IP
Press the number key that corresponds with the phone number you wish to configure
(example is Phone #1). The following window appears:
PHONE /IP NUMBER #1
1- NUMBER
2- PORT NUMBER
3- FORMAT
4- ACCT NUMS
5- TONE
Press the number key that corresponds with your selection. Refer to the next four sub-
sections (Number, Format, Account Numbers and Tone) for explanations of the phone number
options.
Number/IP address
The display scrolls through the Phone /IP Number options. Press [1] for NUMBER. The
following window appears:
PHONE /IP NMBR 1: >????
????????????????
Press [1]. Press [TEST][4] to add the wait for dial tone, and then enter the phone number and
press [#/Enter]. The previous menu appears. You can include several other special control
characters in the phone number by pressing [Test] followed by a digit.
For a list of control characters, see the following table:
Press
See
Action
[TEST] 1
[TEST] 2
[TEST] 3
[TEST] 4
*
Touch Tone “*”
Touch Tone “#”
Three-second delay
Wait for dial tone
#
/
>
Table 8.3: Phone number control characters
Installation and Operation Manual
2012.08 | 04 | F01U008458
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
79
Several keys assist when you enter phone or IP numbers. For these keys, see the following
table:
Press
Action
[SILENCE]
[DISABLE]
Advance to next position
Go back one position
Clear position
[RESET]
Table 8.4: Phone number assistance keys
Notice!
For a phone number, you must enter 1 as a prefix before the special character >. Except for
unusual situations, all phone numbers should have the wait for dial tone character as the sec-
ond digit. This ensures that reports are delivered as quickly as possible, even if an incoming
phone call must be disconnected. For example, you would program 1>18002890096 for the
phone number 1 800-289-0096.
If the wait for dial tone is not specified, the control panel waits 7 sec after going off-hook,
and then dials whether or not the dial tone is present.
To enter a central station IP address in either phone number 1 or 2 in the control panel,
replace all three phone numbers with an IP address. To distinguish an IP address from a
phone number, enter 0 as the first digit, followed by the 12 digit IP address.
Notice!
The IP address must be 12 digits long.For example, if the IP address is 172.30.1.101, the
phone number is programmed as 0 172 030 001 101. Do not add the spaces. They are inclu-
ded for readability.
For programming an IP address and bit locations, see the following table:
Digit 1
Digit 2
IP1
Digit 3
IP2
Digit 4
IP3
Digit 5
IP4
Digit 6
IP5
Digit 7
IP6
Digit 8
IP7
0 = Alt.
Comm.
On
Digit 9
IP8
Digit 10
IP9
Digit 11
IP10
Digit 12
IP11
Digit 13
IP12
Digit 14
Digit 15
Digit 16
Ack Wait
N2
Ack Wait
N1
Ack Wait
N0
Digit 17
Digit 18
Digit 19
Digit 20
Digit 21
Digit 22
Digit 23
Digit 24
HB
HB
HB
1 = Anti-
0 unused 0 unused 0 unused 0 unused
interval
N2
interval
N1
interval
N0
Replay On
Table 8.5: IP address digit or bit location
Acknowledge Wait Time (ACK) – Digits 14 to 16, Default: 010
The alternate communication event, transmission acknowledge wait time, is stored in the
phone number location as digits 14, 15 and 16. The wait time is a number from 1 to 255
seconds where the most significant or first digit is D14.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
80
en | Control Panel Programming
Fire Alarm Control Panels
For example, if the necessary wait time is 30 sec, digits 14 through 16 should be 0, 3, 0
respectively.
In larger installation sites using alternate communications as a destination, set the wait time
to a higher value to compensate for network congestion delays. This wait time is also used for
the heartbeat acknowledge wait time. This is calculated using the following formula:
Value = (D14 X 100 + D15 X 10 + D16), where DXX is a digit number from the table entitled IP
A time-out on an alternate communication path is treated the same way as a negative
acknowledgement and results in the same event routing default scheme used with phone
reporting to the central station. This allows alternate communications to be the primary or
secondary reporting paths to an actual phone number for a single reporting destination.
For the alternate communications path, see the following table:
Attempt
Primary phone line (phone 1)
1st phone number
Secondary phone line (phone 2)
1
2
3
4
5
6
7
8
9
10
2nd phone number
1st phone number
2nd phone number
2nd phone number
1st phone number
1st phone number
2nd phone number
2nd phone number
1st phone number
Table 8.6: Phone reporting
Heartbeat Interval (HB) or Polling Time – Digits 17 to 19, Recommended: 240
This interval is a value between 1 and 255 that indicates the number of seconds between
heartbeat events sent from the control panel. The heartbeat event is sent only when the
communication path is idle for at least the programmed heartbeat interval period of time. The
value is stored in phone number digits 17 through 19 with 17 being the most significant or
first digit. A value of zero in these locations disables the heartbeat feature. These digits are
always zero in the remote programmer phone number. Use the following formula to calculate
this value:
Value = (D17 x 100 + D18 x 10 + D19), where DXX is a digit number from the table entitled IP
The heartbeat feature is an acknowledged test event sent to the central station receiver over a
network connection. This event does not appear at the central station, and it is not logged in
the control panel as an actual event. The heartbeat event is used as a periodic test of the
virtual circuit between the control panel and the networked receiver. The heartbeat event is
transmitted as a null‑Modem IIIa2 event that uses only the first four digits of the account code
for Area 1. The event format always remains the same regardless of the communication
protocol formats available in the control panel.
For acceptable programming selections for UL864 9th edition Listed applications, see
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
81
Anti-Replay – Digit 20, Default: 1
Digit 20 of the phone number enables the Anti-Replay Feature for central station
communications. A zero in this location disables this feature. This digit is always zero in the
remote programmer phone number.
The purpose of Anti-Replay is to prevent malicious or accidental repetition of event packets to
the central station network receiver. A communication packet can be recorded on a network
and replayed in its entirety as if it came from the control panel. If for some reason the packets
become out of sequence, the communication path generates a communications failure event
and must be manually resynchronized.
Port Numbers
Shortcut: 0-PROG, 6-PROG ACC’NTS, 1-PHONE/IP NUMS
The port numbers identify the control panel when it sends reports to the Netcom module. (For
normal installation, set this to 07700).
The display scrolls through the Phone or IP Number options. Press [2] for PORT NUMS. The
following window appears:
PORT #1: 00000
NEW NUMBER: 00000
The existing number is shown on the top line. Enter the new number on the second line and
press [#/Enter]. The previous window appears. Enter hexadecimal digits A through F by
pressing [Test] followed by [1] for A, [2] for B, [3] for C, [4] for D, [5] for E and [6] for F.
Notice!
For more information about using Netcom communications, see also the Installation Guides for
the B420 models, the DX4020, or the ITS-DX4020-G.
Format
Shortcut: 0-PROG, 6-PROG ACC’NTS, 1-PHONE/IP NUMS
Use this feature to select which communication format to use or to disable communication for
the phone or IP number. To disable the dialer, set the format for Phone Lines 1 and 2 to
disabled and turn off the monitoring feature of both lines.
The display scrolls through the Phone or IP Number options. Press [3] for FORMAT. The
following window appears:
PHONE/IP FORMAT ( )
0- DISABLE
1- 3/1 REPORT
2- 4/2 REPORT
3- BSFK REPORT
4- SIA, 110 RPRT
5- CONTACT ID
6- SIA, 300 RPRT
7- MDM 3A2
Press the number key that corresponds to your selection. The previous window appears.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
82
en | Control Panel Programming
Fire Alarm Control Panels
Notice!
If using the B420 models, the DX4020, or the ITS-DX4020-G for reporting events, the Modem
IIIa2 and Contact ID formats are possible:
Account Numbers
Shortcut: 0-PROG, 6-PROG ACC’NTS, 1-PHONE/IP NUMS
The account numbers identify the control panel when it sends reports to the central station.
The display scrolls through the Phone or IP Number options. Press [4] for ACCOUNT NUMS.
The following window appears:
ACCOUNT #1: 0000
NEW NUMBER: 0000
The existing number is shown on the top line. Enter the new number on the second line and
press [#/Enter]. The previous window appears. Enter hexadecimal digits A through F by
pressing [Test] followed by [1] for A, [2] for B, [3] for C, [4] for D, [5] for E and [6] for F.
Tone
Shortcut: 0-PROG, 6-PROG ACC’NTS, 1-PHONE/IP NUMS
The FREQ (_) programming items (refer to window below) modify the reporting format when
3/1 or 4/2 tone burst reporting is selected for the format. Select three parameters with one
setting: data tone frequency, acknowledge tone frequency, and data rate. The frequency that
the control panel uses to send data pulses can be set for 1900 Hz (19D) or 1800 Hz (18D).
The frequency of the acknowledge tone from the receiver to which control panel responds can
be set to 1400 Hz (14A) or 2300 Hz (23A). The rate at which the data pulses are sent can be
set to 10, 20, or 40 pulses per second (10PS, 20PS or 40PS).
The display scrolls through the Phone/IP Number options (refer to 52). Press [5] for TONE.
The following window appears:
FREQ (__)
1- 19D, 14A, 10PS
2- 18D, 23A, 10PS
3- 19D, 14A, 20PS
4- 18D, 23A, 20PS
5- 19D, 14A, 40PS
6- 18D, 23A, 40PS
Press the number key that corresponds to your selection. The previous window appears.
8.6.2
Phone Control
Shortcut: 0-PROG, 6-PROG ACC’NTS, 2-PHONE CONTROL
In addition to features associated with each phone and IP number, each phone line has
associated features.
PHONE CONTROL
1- LINE #1
2- LINE #2
Press the number key that corresponds with your selection. Line 1 and Line 2 have the same
options. The following window appears:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
83
PHONE CONTROL #1
1- MONITOR LINE
2- DIALING TYPE
For explanations of the phone control options, see the following sections for Monitor Line and
Dialing Type.
Monitor Line
Shortcut: 0-PROG, 6-PROG ACC’NTS, 2-PHONE CONTROL
The phone line monitor feature, that supervises the connection of the phone line to the
control panel, can be disabled for each phone line. If an IP address is entered for the Phone/
IP number, set the monitor to No. If this is not programmed to No, a trouble is generated.
Choose Line 1 or Line 2 (see the window above). The display scrolls through the Phone
Control options. Press [1] for MONITOR LINE. The following window appears:
MONITOR LINE #1
_______: YES (1) NO (0)
For acceptable programming selections for UL864 9th edition Listed applications, see
Press [1] for YES or [0/Prog] for NO. The previous window appears.
Dialing Type
Shortcut: 0-PROG, 6-PROG ACC’NTS, 2-PHONE CONTROL
This feature determines the format the control panel uses for dialing on each phone line. The
TONE/PULSE setting first tries tone dialing. If that fails, it switches to pulse dialing. If an IP
address is entered in for the Phone/IP number, the control panel ignores this setting.
Choose Line 1 or Line 2 (see the window below). The display scrolls through the Phone
Control options. Press [2] for DIALING TYPE. The following window appears:
PHONE CONTRO (__)
1- PULSE ONLY
2- TONE/PULSE
3- TONE ONLY
Press the number key that corresponds to your selection. The previous window appears.
8.6.3
Report Steering
Shortcut: 0-PROG, 6-PROG ACC’NTS, 3-RPT STEERING
Different classes of reports can be directed to different phone numbers. Non-supervisory
alarms include fire alarms and waterflow alarms. Supervisory alarms come from points
configured as a supervisory type. Non-supervisory restorals include fire and waterflow
restorals. Supervisory restorals come only from points configured as a supervisory type.
Trouble reports include all point and system troubles and restorals. Tests include Auto Tests,
Manual Tests and Off-normal at Test Reports. The control panel allows the special reports
Silence, Reset, and Drill to be individually directed.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
84
en | Control Panel Programming
Fire Alarm Control Panels
Notice!
If any reports are directed to Phone/IP Number 2 (including the default, PHONE 2 BACKUP), a
phone number and account number must be programmed for Phone/IP Number 2. The con-
trol panel indicates a COMM FAULT if it sends a report (using Phone Number 1 parameters)
which references unprogrammed Phone/IP Number 2 parameters.
The display scrolls through the following items:
REPORT STEERING
1- NONSUP ALRM
2- SUPVSY ALRM
3- NONSUP RSTR
4- SUPVSY RSTR
5- TROUBLE
6- TESTS
7- SILENCE
8- RESET
9- FIRE DRILL
Press the number key that corresponds to your selection. Selecting, for example
NONSUP ALRM produces the following window:
NONSUP ALRM (__)
1- PHONE/IP 1 ONLY
2- PHONE/IP 2 ONLY
3- PHON/IP 1 AND 2
4- PHN/IP 2 BACKUP
5- NO REPORT
PHONE/IP 1 ONLY: Report sent to Phone/IP 1 only.
PHONE/IP 2 ONLY: Report sent to Phone/IP 2 only.
PHONE/IP 1 AND 2: Report sent to Phone/IP Numbers 1 and 2.
PHONE/IP 2 BACKUP: Report sent to Phone/IP 1, then to Phone/IP 2 if 1 fails.
NO REPORT: No report sent.
Press the number key that corresponds with your selection. The previous window appears.
8.6.4
Ring Count
Shortcut: 0-PROG, 6-PROG ACC’NTS, 4-RING COUNT
Notice!
Set to 0 the number of phone rings before the control panel seizes the line to attempt remote
programming. The number of phone rings before the panel seizes the line to attempt remote
programming must remain at 0 for UL864 local, auxiliary or remote station installations. If an
IP address is entered in for the Phone/IP number, the panel will ignore this setting. When the
ring count is set to 0, remote programming must be answered on site. Once answered, the
panel will prompt for a password.
The following window appears:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
85
RING COUNT
(01-15, 00=DIS) _______
Enter the information and press [#/Enter]. The previous window appears. An entry of [0/Prog]
[0/Prog] disables ring detection.
For acceptable programming selections for UL864 9th edition Listed applications, see
8.6.5
Communication Tries
Shortcut: 0-PROG, 6-PROG ACC’NTS, 5-COMM. TRIES
The system default is to try ten times to communicate an event. Bosch recommends setting
this to five tries. This parameter determines after which attempt the system indicates a failure
condition. (After reporting a failure, the system continues to communicate until it reaches ten
times). Do not select 1 or a failure is indicated whenever a report is sent.
The following window appears:
COMM ATTMPTS (__)
(01-10): _______
Enter the information and press [#/Enter]. The previous window appears.
8.6.6
Machine Bypass
Shortcut: 0-PROG, 6-PROG ACC’NTS, 6-MACH BYPASS
The downloading computer must redial the control panel if an answering machine answered
the phone before the control panel. When this option is selected, if the control panel detects
the phone line ringing within one minute of when the last ringing cycle stopped, it answers on
the first ring and seizes the phone line. If an IP address is entered in for the Phone/IP number,
the control panel ignores this setting.
The following window appears:
MACHINE BYPASS
_______: YES (1) NO (0)
Enter the information and press [#/Enter]. The previous window appears.
8.6.7
ALT. COMM
Shortcut: 0-PROG, 6-PROG ACC’NTS, 7-ALTER COMM
This prompt is used with the B420 models, DX4010, DX4020 or ITS-DX4020-G.
If using the DX4010 select 1-serial; for all others, select 0-network. The following window
appears:
ALTER COMM (_)
0 – NETWORK
1 - SERIAL
8.7
PROG FORMATS
PROG FORMATS
1 - 4/2 ZONE REPT
2 - 4/2 RPT CODS
3 - BFSK RPT CDS
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
86
en | Control Panel Programming
Fire Alarm Control Panels
Notice!
This feature offers the use of hexadecimal digits (0 through F). Because the specific keys A
through F are not available on the keypad, use the following equivalent keys: History=A,
Test=B, Disable=C, Drill=D, Silence=E, and Reset=F
NOTICE!
8.7.1
4/2 Zone Report
Shortcut: 0-PROG, 7-PROG FORMATS, 1-4/2 ZONE RPTS
4/2 Zone reports consist of an event type (first digit) and a point number (second digit).
These reports apply only to points, and only when a 3/1 or 4/2 format is selected.
The following window appears:
4/2 ZONE RPT
0- FIRE ALRM D1
1- FIRE RSTR D1
2- WATERFLOW D1
3- SUPERVISE D1
4- TROUBLE D1
5- TRBL RSTR D1
6- DISABLE D1
7- DSBL RSTR D1
8- (RESERVED)
9- MORE
Press the number key that corresponds with your selection of event type (D1 stands for
digit 1). Press [#/Enter].
Pressing [9] retrieves the second digit options (point numbers). The following window
appears:
4/2 ZONE RPT
1- POINT 9 D2
2- POINT 10 D2
3- RETURN TO D1
Press the number key that corresponds to your selection. A window based on your previous
selection allowing entry of hex digits appears:
FIRE ALARM D1 ( )
0 THRU 9
<HISTORY>:A
<TEST>:B
<DISABLE>:C
<DRILL>:D
<SILENCE>:E
<RESET>:F
Enter the digit that corresponds to the selected condition by pressing a number key or one of
the special keys if a hex character is needed. Press [#/Enter] and the previous display
appears.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
87
8.7.2
4/2 Report Codes
Shortcut: 0-PROG, 7-PROG FORMATS, 1-4/2 RPT CODS
4/2 Report Codes apply to system conditions but only when 3/1 or 4/2 format is selected. Two
digits can be programmed to be sent for each condition. The conditions that can be
programmed are:
–
System in test, system in test restore: sent for walk test operations
Silence: sent when the silence key is pressed
Fire drill, fire drill restore: sent for fire drill operations
Open reset report: sent when the reset key is pressed
Low battery, low battery restore, AC failure, AC failure restore: sent for power problems
Test report: sent for manual or automatic communicator tests
Off normal at test: sent if the panel is off-normal at the automatic test time
Phone trouble, restore: sent for phone line problems
System trouble, restore: sent for general system problems
The following window displays:
4/2 RPT CODS
0- SYSTM IN TST
1- SYS TEST RST
2- SILENCE
3- FIRE DRILL
4- FIRE DRL RST
5- OPEN RST RPT
6- LOW BATTERY
7- LOW BATT RST
8- AC FAILURE
9- MORE
Pressing [9] allows programming additional reports:
4/2 RPT CODS
0- AC FAIL RST
1- TEST REPORT
2- OFF NORM TEST
3- PHONE 1 TRBL
4- PN 1 TRB RST
5- PHONE 2 TRBL
6- PN 2 TRB RST
7- SYSTEM TROUB
8- SYS TRB RST
Pressing [9] returns you to the previous group of reporting codes.
Press the number key that corresponds to your code selection. A window based on your
previous selection allowing entry of two hex digits appears:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
88
en | Control Panel Programming
Fire Alarm Control Panels
SYSTM IN TST ( )
0 THRU 9
<HISTORY>: A
<TEST>: B
<DISABLE>: C
<DRILL>: D
<SILENCE>: E
<RESET>: F
Enter digits that correspond to the selected condition by pressing a number key, or one of the
special keys if a hex character is needed. Press [#/Enter] and the previous display appears.
8.7.3
BFSK Report Codes
Shortcut: 0-PROG, 7-PROG FORMATS, 1-BFSK RPT CODS
When BFSK reporting is used, most reporting codes are fixed and do not need programming.
There are five reports that the control panel can send that are not standard BFSK codes:
Off normal at test: Sent if the panel is off-normal at the automatic test time.
Open reset report: Sent when the reset key is pressed.
Silence: Sent when the silence key is pressed.
Fire drill, fire drill restore: Sent for fire drill operations.
The following window displays:
BFSK RPT CDS
1- OFF NORM TEST
2- OPEN/RESET
3- SILENCE
4- FIRE DRILL
5- FR DRIL RSTR
Press the number key that corresponds to your report code selection. A window allowing
entry of two hex digits appears.
8.8
HISTORY DEFAULTS
Shortcut: 0-PROG, 8-HSTRY DEFLTS
The following window appears:
PROG DEFAULTS
1- CLEAR HSTRY
2- DEFAULT EE
3- ALT 4/2 CDES
4- (reserved)
8.8.1
Clear History
Shortcut: 0-PROG, 8-HSTRY DEFLTS, 1- CLEAR HISTORY
You can use this option to clear some or all of the history records in the system.
The following window appears:
HIST ITEMS= _______
DEL OLDEST 000
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
89
Enter the number of history records you wish to delete, and press [#/Enter]. The previous
menu appears.
8.8.2
Default EE
Warning!
Lost programming!
All programming, including zone configurations and option installations, are lost when this op-
eration is performed. You must turn control panel power off and on after resetting the de-
fault, to reinstall the four zone expanders and the MUX expander. You must update the option
bus and set up keypads (PROG SYSTEM MENU) to reinstall option bus devices.
!
Shortcut: 0-PROG, 8-HSTRY DEFLTS, 2- DEFAULT EE
You can set the control panel back to the original factory-programming configuration with this
option. You are asked to press [#/Enter] to complete the operation. Press [*/Back] to cancel
the operation.
The following window appears:
SETTING EEPROM
TO DEFAULT...
When the operation is complete, the previous menu appears. This operation takes several
minutes when the D7039 Multiplex Expander is installed.
8.8.3
Alternate 4/2 Codes
Shortcut: 0-PROG, 8-HSTRY DEFLTS, 3- ALT 4/2 CDES
You can set all of the programming for 4/2 codes to an alternative set of default reports, as
option.
The following window appears:
SETTING EEPROM
TO DEFAULT...
When the operation is complete, the previous menu appears.
8.9
Program MUX
Shortcut: 0-PROG, 9-PROGRAM MUX
Warning!
1. Unprogrammed devices on the bus will not operate or be supervised
2. This menu is accessible only when the D7039 Multiplex expander is installed.
3. Do not install more than one device programmed to the same address on the bus. Doing so
can inhibit alarm reporting from both devices.
!
Notice!
Intermittent trouble reports from a particular MUX point address can indicate that more than
one device was programmed to that address.
The following window appears:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
90
en | Control Panel Programming
Fire Alarm Control Panels
PROGRAM MUX
1- MUX EDIT
2- MUX PROGRAM
3- BUS TYPE
4- AUTO PROGRAM
8.9.1
MUX Edit
Shortcut: 0-PROG, 9-PROGRAM MUX, 1- MUX EDIT
To add MUX devices to the system, use the MUX Edit option. Each device must have a unique
address programmed using the address switches.
The following window appears:
DEVICE TYPE ( )
0- NO DEVICE
DescriptionModel
0- NO DEVICE
2- SINGLE INPUT
3- I/O MODULE
4- MUX SMOKE
5- SMOKE W/FRZ
6- DUAL INPUT
7- OCTAL INPUT
2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class A)
3- I/O MODULE D7053
4- MUX SMOKE D7050, D7050TH, D343
5- SMOKE W/FRZ Not Used
6- DUAL INPUT D7052(Class B)
7- OCTAL INPUT D7042
Press the number that corresponds with the device you are adding or press [0/Prog] if you are
removing a device. When the device type is selected, the following window appears:
POINT NUMBER
(009 - 255) 009
Enter the address of the point being added, and press [#/Enter]. The device type window
appears again allowing additional devices to be added. Eight points are added at once when
the D7042 is added to the control panel.
8.9.2
MUX Program
Shortcut: 0-PROG, 9-PROGRAM MUX, 2-MUX PROGRAM
To add MUX devices to the system simultaneously while programming an address into the
device itself, use the MUX Program option. This programs a specified address into the device,
and also sets the control panel to use the device.
Warning!
Programming issues!
The D7042 is programmed using switches and cannot be added using the MUX Program fea-
ture. Use MUX Edit instead.
!
All devices must be removed from MUX bus A before programming by removing power from
the system, disconnecting the wires to the field devices, and re-powering the system. Failure
to disconnect devices results in all devices on loop A being programmed to the new address.
All programming is performed on Bus A, including addresses 129 to 255 that can only be
installed on Bus B for operation. Be sure to connect devices with addresses 129 to 255 to
Bus B, not to Bus A.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
91
If no devices are connected on Bus A, the following window appears. Otherwise an error
message appears.
PROGRAM MUX
1- NORMAL
2- FAST
Select normal programming to add one or two devices. Select fast programming to program
larger quantities of identical devices to sequential addresses.
Normal Programming
If normal programming is selected, the following menu appears allowing selection of the
device type being programmed:
DEVICE TYPE ( )
0- NO DEVICE
DescriptionModel
0- NO DEVICE
2- SINGLE INPUT
3- I/O MODULE
4- MUX SMOKE
5- SMOKE W/FRZ
6- DUAL INPUT
7- OCTAL INPUT
2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class A)
3- I/O MODULE D7053
4- MUX SMOKE D7050, D7050TH, D343
5- SMOKE W/FRZ Not Used
6- DUAL INPUT D7052(Class B)
7- OCTAL INPUT D7042
Enter the number that corresponds with the device you are adding, or select 0 if you are
removing a device. When the device type is selected, the following window appears:
POINT NUMBER
(009 - 255) 009
Enter the address of the point being added, and press [#/Enter]. The display asks you to
attach the device being programmed to the terminals for MUX bus A (see the following
window). You can simply hold the device wires on the terminals for the few seconds it takes
to program. The programming operation retries up to three times if the device does not
connect right away.
POINT NUMBER 009
ATTACH DEVICE
Then, the display automatically shows:
POINT NUMBER 009
PROGRAMMING
If the device added is an I/O module, you are asked to enter the four zones to control the relay
output, just as for other relay devices:
OUTPUT ZONE A: _______
(00 - 63): _______
Enter the first zone (00 to 63) you want to assign to this output and press [#/Enter]. A similar
display for Zone B, C and D appears allowing up to four zones to control this output. When all
four zones are assigned, the previous window appears. It confirms the programming operation
and returns to the previous menu.
POINT NUMBER 009
PROGRAMMED
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
92
en | Control Panel Programming
Fire Alarm Control Panels
If a device is defective or not connected properly, the control panel shows:
ERROR -
DEVICE FAILED
Fast Programming
Fast programming proceeds the same as normal programming, except that when the device is
programmed you are asked to remove the device:
POINT NUMBER 009
REMOVE DEVICE
Then, you are asked to attach the next device at the next address:
POINT NUMBER 010
ATTACH DEVICE
This process continues until you press [*/Back]. All devices to be programmed must be of the
same type.
8.9.3
MUX Bus Type
Shortcut: 0-PROG, 9-PROGRAM MUX, 3- BUS TYPE
This option configures the system for two independent Class B, Style 4 buses allowing
addresses up to 255.
Notice!
Class A operation is not supported by the D7042 Eight Input Module; do not select Class A
operation.
The following window appears:
MUX BUS TYPE ( )
1- CLASS A
2- CLASS B
Press [2] to select Class B operation if the setting was changed from the default setting.
For wiring details for a Class B configuration, see also the D7042/D7042B Multiplex Eight Input
Remote Modules Installation Instructions (P/N: 42638)
For more information regarding Class A and Class B wiring instructions, see also the D7039
Multiplex Expansion Module’s Installation Guide (P/N: 38685).
For mounting locations inside the FPD‑7024’s enclosure and wiring possibilities for the D7039
and its I/O module, see the following figure:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
93
Figure 8.1: D7039 Mounting Location
1 D7039 MUX Expansion module
5 Addresses 9 to 128
2 Enclosure
6 MUX Class A
3 FPD‑7024 Control board
7 Addresses 129 - 255
8 MUX Class B
4 I/O module for the D7039 MUX
Expansion module
8.9.4
AUTO PROGRAM
Shortcut: 0-PROG, 9-PROGRAM MUX, 4- AUTO PROGRAM
This option provides a convenient way for the installer to configure the FPD‑7024 to operate
with the existing devices on the multiplex buses by scanning the buses for missing or new
multiplex devices.
The following display appears:
AUTO PROGRAM?
_______:YES(1) NO(0)
Press [1] to continue with auto programming or [0/Prog] to cancel. When you press [1], the
FPD‑7024 checks for existing programming errors in which devices are programmed
incorrectly in the space required for a lower-addressed multi-point device (such as a dual
point module). If a point is found to be programmed under another device, the following error
message appears for five seconds, and the auto programming process aborts:
ADDRESS ERROR 1
AT ADDRESS xxx
If no errors are found, the FPD‑7024 starts a scanning process that takes approximately one
minute to complete, while showing the following display:
AUTO PROGRAM
SCANNING
PLEASE WAIT...
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
94
en | Control Panel Programming
Fire Alarm Control Panels
When the scanning is completed, the FPD‑7024 checks for missing devices. Missing devices
are addresses with no devices on the multiplex buses, but are programmed into the
FPD‑7024’s site-specific memory area. If missing devices are detected, the FPD‑7024 shows
the following menu (where xxx is the address of the first point of the missing device):
MISSING PT @ xxx
0- DELETE POINT
1- KEEP POINT
2- DEL REMAIN
3- KEEP REMAIN
DELETE POINT: If selected, the missing point and any addresses it implemented (up to eight
for an octal input module) are permanently deleted from the site specific memory area. If the
deleted device is an I/O module, the output zones that were programmed for the relay are
reset to 0. If additional devices are found to be missing, the above display is repeated for each
missing device.
KEEP POINT: If selected, the FPD‑7024 retains the programming for the existing point and
continues scanning for additional missing points.
DEL REMAIN: If selected, the following prompt # KEY TO CONFIRM appears at the FPD‑7024.
If the [#/Enter] key is pressed, all the missing points are deleted from the site-specific memory
area and the auto program process continues with the devices found menu. If any other key is
pressed, the existing point is kept and the control panel continues scanning for additional
missing devices.
KEEP REMAIN: If selected, no additional points are deleted and the auto program process
continues with the Devices Found menu. Points individually deleted with the Delete Point
command before selecting the Keep Remain command stay deleted when Keep Remain is
selected.
Warning!
Missing points!
Use the DEL REMAINING feature with caution. Any devices missing from the multiplex buses
during the DEL REMAINING operation, even momentarily, are permanently deleted. These
points do not operate, and do not generate trouble conditions even if they are returned to the
bus.
!
When the delete point operation is finished, the FPD‑7024 shows for five seconds the total
number of points that were deleted from the control panel (xxx indicates the number of points
that were removed from the control panel’s site specific configuration).
AUTO PROGRAM
xxx POINTS DELETED
Confirm that only the expected number of points was removed from the system. Points that
are removed from the control panel’s site-specific configuration do not operate and are not
supervised even if they are returned to the bus.
When the point delete process completes, the auto programming process automatically
checks for new devices on the buses. New devices are found when a device is present on one
of the multiplex buses, but its address is not programmed into the control panel’s site-specific
memory. If new devices are detected, the FPD‑7024 shows the following menu (where xxx is
the address of the first new device found):
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
95
NEW DEVICE @ xxx
2 – SINGLE INPUT
3 – I/O MODULE
4 – MUX SMOKE
5 – SMOKE W/FRZ
6 - DUAL INPUT
7 - OCTAL INPUT
0 – NO DEVICE
Use this menu to define the device type. Press the number key that corresponds with the
device type installed at the address. If a detected device should not be installed and should be
left inactive, press [0/Prog] to bypass the new device.
Warning!
Device malfunction!
!
Ensure that the correct device type is selected for each point. Incorrectly specified device
types can cause multiplex devices to malfunction or fail to operate.
All inputs are configured to use Point Function 10 as they are added. Points added during auto
programming are configured for the following operation:
–
–
–
–
–
Point Function 10 (Fire Alarm, Fast Response, Non-silenceable, Not Local-only)
Open Status = Trouble
Output Zone 9
Alarm Verify = NO
Latching = YES
The programming of input points can be changed when auto programming completes using
the input-programming menu.
When I/O modules are added during auto programming, the relay (second point) is configured
to activate on any alarm, non-silenceable (Zone 63). This can be changed when auto
programming completes by using the output-programming menu.
The FPD‑7024 performs some basic error checks when new devices are added. The following
errors can be shown during the process of adding a device:
ADDRESS ERROR #
AT ADDRESS xxx
In the previous message, # is replaced by a code number and xxx is replaced by the affected
address that indicates the type of error.
For code numbers and corresponding error message descriptions, see the following table:
Code
Error
Description
1
New point is under an existing
point
The new point is in the space required for an
existing multi-address device. This is checked
when auto programming first starts.
2
Point overlaps existing point
There are already devices configured at one of
the addresses required for the new multi-point
device.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
96
en | Control Panel Programming
Fire Alarm Control Panels
3
4
Point is at an illegal address
The addresses at which multi-address devices
can be installed are restricted.
Too many multiplex relays
Only 20 input output devices can be supported
on a given bus.
Table 8.7: Auto programming error messages
For details on installation restrictions, see also the specific device’s installation instructions
When the point adding operation completes, the FPD‑7024 shows for five seconds the total
number of points that were added to the control panel. Confirm that the number of devices
added matches the expected number.
AUTO PROGRAM
xxx POINTS ADDED
Warning!
Undetected devices!
!
If a new device is not detected on the bus during the point adding operation, the device does
not operate and does not generate trouble conditions even if it remains connected to the bus.
When the point adding operation completes, the display shows the total number of points on
the system:
AUTO PROGRAM
xxx MUX POINT
Note that xxx is the total number of points, not devices.
Confirm that the system shows the exact number of points expected. Points that are not
included in the total count do not operate and do not generate trouble conditions.
After the count of total points appears for approximately 10 sec, the FPD‑7024 restores the
multiplex system to normal operation. This process takes approximately 50 sec and the
following message appears during the restoral process:
AUTO PROGRAM
RESTORING
PLEASE WAIT...
Warning!
Test for proper operation!
As with any programming change to a system, test the system for proper operation before re-
turning it to service. At least test each added multiplex point after auto programming com-
pletes. Test according to NFPA 72.
!
8.9.5
Removing MUX Devices
Shortcut: 0-PROG, 9-PROGRAM MUX, 1- MUX EDIT
To remove a previously programmed multiplex device, use the MUX Edit feature.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Control Panel Programming | en
97
PROGRAM MUX
1- MUX EDIT
2- MUX PROGRAM
3- BUS TYPE
4- AUTO PROGRAM
From the Program MUX menu, press [1] to select MUX Edit. The following window appears:
DEVICE TYPE ( )
0- NO DEVICE
Description Model
0- NO DEVICE
2- SINGLE INPUT
3- I/O MODULE
4- MUX SMOKE
5- SMOKE W/FRZ
6- DUAL INPUT
7- OCTAL INPUT
2- SINGLE INPUT D7044/M, D7045, FMM-7045, D7052(Class
A)
3- I/O MODULE D7053
4- MUX SMOKE D7050, D7050TH, D343
5- SMOKE W/FRZ Not Used
6- DUAL INPUT D7052(Class B)
7- OCTAL INPUT D7042
Press [0/Prog] for No Device. Then enter the address for the point you wish to delete.
After the device is successfully deleted, you return to the Device Type (MUX Edit) sub-menu.
An unsuccessful deletion results in an error message (see below) followed by the Device Type
(MUX Edit) sub-menu.
ERROR –
DEVICE FAILED
Warning!
Dual point removal!
If you remove one point of a dual point address (for example, a D7042 Eight Point Input Mod-
ule), the second point (and subsequent points) at this address are also removed. For exam-
ple, if the first point of a D7042 is removed, the remaining seven points are also removed.
!
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
98
en | Specifications
Fire Alarm Control Panels
9
Specifications
Notice!
When a local relay is programmed for trouble it is energized in the normal state. This causes
the common and normally-open terminals to be shorted when not in the trouble condition.
Electrical
Power (Input):
120 V 60 Hz or 220 V 50 Hz, 2.2 A
24 VDC nominal, unfiltered, 1.0 A
24 VDC nominal, filtered, 1.0 A.
12 VDC nominal, 500 mA
Power (Auxiliary):
Power (Initiating Circuit [Smoke])1:
Power (Option Bus):
Power (Notification Appliance Circuit
[NAC])2:
Each NAC has 24 VDC nominal, unfiltered
power with up to 2.5 A capacity (but limited
by overall 4.0 A capacity)
Power (Optional Standby Batteries):
Two 12 V (in series), 7 Ah to 40 Ah
1 For compatible smoke detection devices, see also the FPD‑7024 Smoke Detector
Compatibility List.
2 For compatible NAC devices, see also the FPD‑7024 NAC Compatibility List
Environmental
Temperature (operating and storage):
+32°F to +120°F (0°C to +49°C)
Notification Appliance Circuits (NACs)
Wiring:
standard Class B, Style Y or Class A, Style Z as needed.
Notification patterns:
Configurable for steady, pulsing, California March, ANSI code 3,
synchronized Wheelock, synchronized Gentex, and synchronized
System Sensor.
Relays
Local (on-board):
The main control panel includes Three Form “C” relays. The relay
contacts are rated at 5 A, 28 VDC. No over existing limiting is
performed on the contacts of these relays. The default selection
for the relays is to indicate general alarm and general system
trouble and supervisory. By using point or zone mapping, they
can be programmed to activate in a wide variety of conditions.
Remote1:
Eight Form C relay outputs are provided by a D7035 Remote
Relay Module. The module connects to the FPD‑7024 through the
option bus. The outputs are fully programmable, exactly as the
local relays are programmed. Each output operates independently
of the other seven to provide complete flexibility. Communication
with the D7035 is supervised.
Contact Rating: 5 A at 28 VDC
Number of Modules: two units maximum.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en
99
10
Appendices
10.1
Abbreviation
3/1
Appendix A: Abbreviations on Control Panel Display
Definition
Abbreviation
Definition
3/1 Tone Burst (reporting
format)
KPAD, KYPAD, KYPD
Keypad
4/2
@
4/2 Tone Burst (reporting
format)
LRelay
LOC
Local Relay
Local
Option Bus Address (1 -
16)
ACTVTN
A, ALRM
ALT
Activation
Alarm
MACH
Answering Machine
Monitor
M, MONI, MON
NAC
Alternate
Notification Appliance
Circuit
ANN, ANUN
BAT, BATT, BATTRY
BX
Annunciator
Battery
NMBR, NUM
NONSUP
NORM, NRM
OUT
Number
Non-Supervisory
Normal
Box (e.g. city box)
Catastrophe
Codes
CATE
Output
CDES, CODS, CDS
CMPTR
OVRC
Overexisting
Positive Alarm Sequence
Phone
Computer
Communicator
Configure
Description
Digit
PAS
COMM
PHN, PHON
PROG, PRGMNG
PRGMMD
PT, PNT
PWR
CONFIG
DESCRIPTION
DIG
Programming
Programmed
Point
DLY
Delay
Power
DRL, DRIL
D, DSBL, DISABL
DSPLY
Drill
REM, REMOT
RESPNS
RLY
Remote
Disable
Response
Relay
Display
EE
EEPROM
Expander Relay
Expander
Failure
RPRT, RPT
RST
Report
ERelay
Restore
EXP
SIL
Silence
FAIL
SMK
Smoke
F, FIR, FR
Fire
S, SUPERVISORY,
SUPRVSRY, SUPV, SPV,
SUPVSY
Supervisory
FLT
Fault
SHRT
Short
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
100 en | Appendices
Fire Alarm Control Panels
Abbreviation
Definition
Frequency
Abbreviation
SYS, SYSTM
Definition
FRQNCY, FREQ,
FREQUENCY
System
FUNC
GRND
HI
Function
T, TRBL, TRB, TROUB
TST
Trouble
Test
Ground
High
VER
Version
HSTRY
INIT
IP
History
W, WFLW, WTF
ZN, ZON
Waterflow
Zone
Initialize
Internet Protocol address
Table 10.1: Abbreviations on control panel display
10.2
Appendix B: Control Panel Display Descriptions
The meanings of control panel messages are given in the following table:
FPD-7024 Panel Display
Message
Panel Display Message Definition
FIRE DIRTY PT XX
A smoke detector with the Chamber Check feature indicates a dirty
chamber.
FIRE DSBL PT
Fire point is disabled from the keypad.
FIRE TRBL PT XXX
Trouble condition for specific points on the system. Check control
panel wiring and field wiring for shorts or opens. Also check point
programming to ensure the control panel knows what points belong
on the system.
FIRE TROUBLE
General fire zone trouble message. Refer to the second line of
display for more information.
INST FLT 4Z EXP
There is a missing FPD-7034 Four Zone Expander Board, or the
expander appeared unexpectedly since the last time the system
was powered.
INST FLT MX EXP
There is a missing D7039 MUX Expander Module, or the expander
appeared unexpectedly since the last time the system was
powered.
MONI DSBL PT
Monitor point is disabled from the keypad.
Trouble with a monitor point occurred.
MONI TRBL PT XXX
MUX BUS A FAILURE
MUX BUS B FAILURE
A wiring problem on Bus A or Bus B in Class B mode occurred.
Check the wiring for shorts or opens.
MUX CPU FAILURE
A CPU failure on the D7039 Expander Board occurred. Ensure that
the D7039 is correctly installed on the header pins. If the message
persists, call for service immediately.
SUPV DSBL PT
Supervisory point is disabled from the keypad.
Trouble with a supervisory point occurred.
SUPV TRBL PT XXX
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 101
FPD-7024 Panel Display
Message
Panel Display Message Definition
SYSTEM TROUBLE
TRBL OPEN LNAC
TRBL OPEN RNAC
TRBL OPT BUS@XX
General trouble message. Refer to second line of the display for
more information.
A Local NAC circuit is open. Check the field wiring and the EOL
resistor.
An FPD‑7038 Remote NAC circuit is open. Check the field wiring
and the EOL resistor.
A wiring fault on option bus terminals 7 to 14, as well as specific
address problems with option bus devices occurred. Check the
wiring for the specific device address shown.
TRBL OVRC LNAC
TRBL OVRC RNAC
An overexisting condition on one of the NAC circuits occurred.
Check the field wiring on the notification appliances for shorts.
TRBL SHRT LNAC
TRBL SHRT RNAC
TROUBLE AC FAIL
A short on the Local NAC circuit occurred.
A short on the FPD‑7038 Remote NAC circuit occurred.
AC power failure to the control panel. Check the circuit breaker or
fuse for AC power problem.
TROUBLE ANN
Trouble with one or more annunciators connected to the control
panel.
TROUBLE COMM FLT
A communicator problem occurred. Check the control panel’s
phone lines and programming for the communicator problem.
TROUBLE EEPROM
TROUBLE EXP
An EEPROM failure occurred. Call for service immediately.
An FPD‑7034 Four Zone Expander board problem occurred. Ensure
that the FPD‑7034 is properly connected to the FPD‑7024 PCB.
TROUBLE GRND FLT
TROUBLE KPAD@XX
TROUBLE LOW BATT
TROUBLE MUX CLASS A
TROUBLE PHONE
A ground fault problem occurred. Ensure that no control panel
wiring is shorted to the earth ground.
A specific keypad address failure occurred. Check the keypad’s
wiring and address settings.
The control panel’s battery charger is not working, or the backup
batteries are missing.
A failure on the MUX wiring in Class A mode occurred. Check the
wiring for shorts or opens.
A problem with the control panel’s phone lines occurred. Check the
phone wiring and line monitor programming.
TROUBLE RELAY@XX
TROUBLE SMK PWR
WFLOW DSBL PT
One of the control panel’s auxiliary relays might be shorted.
A short on the smoke power terminals 24 and 25 occurred.
Waterflow point is disabled from the keypad.
WFLW TRBL PT XXX
Trouble with a waterflow or sprinkler point occurred.
Table 10.2: Control panel display
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
102 en | Appendices
Fire Alarm Control Panels
10.3
Appendix C: Reporting Summary for Fire Communicator
Notice!
For information about the receiver output when the Modem IIIa2 reporting format is used with
Notice!
Cause of Hazard
When the Modem IIIa2, SIA or Contact ID reporting formats are used, an additional numeric
identifier is sent with system trouble messages that provide a specific indication of the partic-
For report codes (Items in boldface type are not programmable), see the following table:
Default Values
Alternate Default
Report
Index
3/1
BFSK
SIA
Contact ID
4/2
4/2
4/2
4/2
digit 1
digit 2
digit 1
digit 2
POINT FIRE ALARM
0
0
0
p
0
0
p
0
0
z0
FAz
1 110 00 zzz
1 113 00 zzz
POINT WATERFLOW
ALARM
1
2
3
p
p
p
p
p
p
z0
z0
z0
SAz
SSz
UAz
POINT SUPERVISORY
ALARM
0
0
6
0
0
6
0
0
6
1 200 00 zzz
1 140 00 zzz
POINT MONITOR
ALARM
POINT FIRE TROUBLE
4
5
p
p
p
p
Fz
Fz
FTz
STz
1 373 00 zzz
1 373 00 zzz
POINT WATERFLOW
TROUBLE
see #4
see #4
see #4
see #4
see #4
see #4
see #4
see #4
see #4
POINT SUPERVISORY
TROUBLE
6
7
p
p
p
p
Fz
Fz
STz
UTz
1 373 00 zzz
1 373 00 zzz
POINT MONITOR
TROUBLE
POINT FIRE DIRTY
8
9
see #4
see #4
p
p
see #4
see #4
p
p
see #4
see #4
Fz
Fz
FSz
FSz
1 385 00 zzz
1 385 00 zzz
POINT WATERFLOW
DIRTY
POINT SUPERVISORY
DIRTY
10
11
see #4
see #4
p
p
see #4
see #4
p
p
see #4
see #4
B
Fz
Fz
Fz
FSz
UTz
1 385 00 zzz
1 373 00 zzz
POINT MONITOR
DIRTY
POINT FIRE DISABLE
12
13
B
p
p
5
p
p
FBz
FBz
1 571 00 zzz
1 571 00 zzz
POINT WATERFLOW
DISABLE
see #12
see #12
see #12 Fz
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 103
Default Values
Alternate Default
Report
Index
3/1
BFSK
SIA
Contact ID
4/2
4/2
4/2
4/2
digit 1
digit 2
digit 1
digit 2
POINT SUPERVISORY
DISABLE
14
15
16
17
18
19
see #12
see #12
3
p
see #12
see #12
2
p
see #12 Fz
see #12 Fz
FBz
1 571 00 zzz
1 571 00 zzz
3 110 00 zzz
3 113 00 zzz
3 200 00 zzz
3 140 00 zzz
3 373 00 zzz
3 373 00 zzz
3 373 00 zzz
3 373 00 zzz
POINT MONITOR
DISABLE
p
p
P
P
p
p
p
p
p
p
p
P
P
p
p
p
p
p
FBz
FRz
SHz
SRz
URz
FJz
SJz
SJz
UJz
POINT FIRE ALARM
RESTORE
3
Ez
POINT WATERFLOW
RESTORE
see #16
see #16
see #16
3
see #16
see #16
see #16
7
see #16 Ez
see #16 Ez
see #16 Ez
POINT SUPERVISORY
RESTORE
POINT MONITOR
RESTORE
POINT FIRE TROUBLE 20
RESTORE
3
Ez
POINT WATERFLOW
TROUBLE RESTORE
21
22
23
see #20
see #20
see #20
see #20
see #20
see #20
see #20 Ez
see #20 Ez
see #20 Ez
POINT SUPERVISORY
TROUBLE RESTORE
POINT MONITOR
TROUBLE RESTORE
POINT FIRE DIRTY
24
25
see #20
see #20
p
p
see #20
see #20
p
p
see #20 Ez
see #20 Ez
FJz
FJz
3 385 00 zzz
3 385 00 zzz
POINT WATERFLOW
DIRTY RESTORE
POINT SUPERVISORY
DIRTY RESTORE
26
27
28
29
30
31
40
see #20
see #20
3
p
p
p
p
p
p
1
see #20
see #20
2
p
p
p
p
p
p
3
see #20 Ez
see #20 Ez
FJz
UJz
FHz
FHz
FHz
FHz
TS0
3 385 00 zzz
3 373 00 zzz
3 571 00 zzz
3 571 00 zzz
3 571 00 zzz
3 571 00 zzz
POINT MONITOR
DIRTY RESTORE
POINT FIRE DISABLE
RESTORE
A
Ez
POINT WATERFLOW
DISABLE RESTORE
see #28
see #28
see #28
F
see #28
see #28
see #28
3
see #28 Ez
see #28 Ez
see #28 Ez
POINT SUPERVISORY
DISABLE RESTORE
POINT MONITOR
DISABLE RESTORE
SYSTEM IN TEST
F
FD
1 607 00
000
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
104 en | Appendices
Fire Alarm Control Panels
Default Values
Alternate Default
Report
Index
3/1
BFSK
SIA
Contact ID
4/2
4/2
4/2
4/2
digit 1
digit 2
digit 1
digit 2
SYSTEM IN TEST
RESTORE
41
42
43
44
45
46
47
48
49
50
E
1
F
2
2
F
9
9
3
9
3
3
9
6
7
6
7
3
3
3
3
3
3
7
F
3
7
F
9
9
0
0
0
3
1
5
2
6
E
9
F
E
9
F
E
F
E
E
F
F
E
F
E
ED
FD
FD
ED
FD
F9
E9
FA
EA
EE
FD
FB
EB
FC
EC
TE0
3 607 00
000
SILENCE
9
F
E
9
F
E
F
E
E
F
F
E
F
E
KBuu 1 400 00
uuu
FIRE DRILL
FI0
1 607 00
000
FIRE DRILL RESTORE
SYSTEM RESET
LOW BATTERY
FK0
3 607 00
000
ORuu 1 305 00
uuu
YT0
YR0
AT0
AR0
RP0
YX0
LT1
LR1
LT2
LR2
1 302 00
000
LOW BATTERY
RESTORE
3 302 00
000
AC FAIL
A
A
E
D
B
B
C
C
1 301 00
000
AC FAIL RESTORE
AUTO TEST
3 301 00
000
1 602 00
000
OFF NORMAL AT TEST 51
1 608 00
000
PHONE 1 TROUBLE
PHONE 1 RESTORE
PHONE 2 TROUBLE
PHONE 2 RESTORE
SYSTEM TROUBLE
52
53
54
55
1 351 00
000
3 351 00
000
1 352 00
000
3 352 00
000
56
57
F
E
D
D
3
3
3
7
F
E
FD
ED
ET
ER
1 300 00 ccc
3 300 00 ccc
SYSTEM TROUBLE
RESTORE
MANUAL TEST
58
59
see #50 see #50 see #50 see #50 see #50 EE
see #56 see #56 see #56 see #56 see #56 FD
RX0
RT0
1 601 00
000
DATA LOST
1 354 00
000
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 105
Default Values
Alternate Default
Report
Index
3/1
BFSK
SIA
Contact ID
4/2
4/2
4/2
4/2
digit 1
digit 2
digit 1
digit 2
EEPROM FAILURE
60
61
see #56 see #56 see #56 see #56 see #56 FD
see #57 see #57 see #57 see #57 see #57 ED
see #56 see #56 see #56 see #56 see #56 FD
see #57 see #57 see #57 see #57 see #57 ED
UT18 1 307 00
018
EEPROM RESTORAL
UJ18 3 307 00
018
SMOKE POWER FAULT 62
YP0
YQ0
RU0
RS0
1 320 00
000
SMOKE POWER
RESTORE
63
66
67
3 320 00
000
REMOTE
F
E
D
D
F
E
D
D
F
E
FD
ED
1 413 00
000
PROGRAMMING FAIL
REMOTE
1 412 00
000
PROGRAMMING
SUCCESS
Notes:
c: system trouble condition code
p: programmable digit for each zone u: user ID digit
z: zone digit
Table 10.3: Reporting summary for fire communicator
Notice!
Cause of Hazard
The Modem IIIa2 reports are fixed and do not require programming.
For Modem IIIa2 report codes, see the following table:
Report
Index
Receiver output
POINT FIRE ALARM
0
dd/dd tt:tt ql ACCT aaaa FIRE ALARM
+++ ACCT aaaa AREA=1 POINT=zzz
POINT WATERFLOW ALARM
POINT SUPERVISORY ALARM
POINT MONITOR ALARM
POINT FIRE TROUBLE
1
2
3
4
5
dd/dd tt:tt ql ACCT aaaa FIRE ALARM
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE SUPRVISION
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE ALARM
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TROUBLE
+++ ACCT aaaa AREA=1 POINT=zzz
POINT WATERFLOW TROUBLE
dd/dd tt:tt ql ACCT aaaa FIRE TROUBLE
+++ ACCT aaaa AREA=1 POINT=zzz
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
106 en | Appendices
Fire Alarm Control Panels
Report
Index
Receiver output
POINT SUPERVISORY TROUBLE
6
dd/dd tt:tt ql ACCT aaaa FIRE TROUBLE
+++ ACCT aaaa AREA=1 POINT=zzz
POINT MONITOR TROUBLE
POINT FIRE DIRTY
7
dd/dd tt:tt ql ACCT aaaa FIRE TROUBLE
+++ ACCT aaaa AREA=0 POINT=zzz
8
dd/dd tt:tt ql ACCT aaaa ANALOG SERVICE
+++ ACCT aaaa AREA=0 POINT=zzz
POINT WATERFLOW DIRTY
POINT SUPERVISORY DIRTY
POINT MONITOR DIRTY
9
dd/dd tt:tt ql ACCT aaaa ANALOG SERVICE
+++ ACCT aaaa AREA=1 POINT=zzz
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
dd/dd tt:tt ql ACCT aaaa ANALOG SERVICE
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TROUBLE
+++ ACCT aaaa AREA=1 POINT=zzz
POINT FIRE DISABLE
dd/dd tt:tt ql ACCT aaaa COMMAND BYPASS
+++ ACCT aaaa AREA=1 ID=uuu POINT=zzz
POINT WATERFLOW DISABLE
POINT SUPERVISORY DISABLE
POINT MONITOR DISABLE
POINT FIRE ALARM RESTORE
POINT WATERFLOW RESTORE
POINT SUPERVISORY RESTORE
POINT MONITOR RESTORE
POINT FIRE TROUBLE RESTORE
POINT WATERFLOW TROUBLE RESTORE
POINT SUPERVISORY TROUBLE RESTORE
POINT MONITOR TROUBLE RESTORE
POINT FIRE DIRTY
dd/dd tt:tt ql ACCT aaaa COMMAND BYPASS
+++ ACCT aaaa AREA=1 ID=uuu POINT=zzz
dd/dd tt:tt ql ACCT aaaa COMMAND BYPASS
+++ ACCT aaaa AREA=1 ID=uuu POINT=zzz
dd/dd tt:tt ql ACCT aaaa COMMAND BYPASS
+++ ACCT aaaa AREA=1 ID=uuu POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE ALM RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE ALM RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE ALM RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE ALM RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa ANALOG RESTORE
+++ ACCT aaaa AREA=1 POINT=zzz
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 107
Report
Index
Receiver output
POINT WATERFLOW DIRTY RESTORE
25
dd/dd tt:tt ql ACCT aaaa ANALOG RESTORE
+++ ACCT aaaa AREA=1 POINT=zzz
POINT SUPERVISO Y DIRTY RESTORE
POINT MONITOR DIRTY RESTORE
POINT FIRE DISABLE RESTORE
POINT WATERFLOW DISABLE RESTORE
POINT SUPERVISORY DISABLE RESTORE
POINT MONITOR DISABLE RESTORE
SYSTEM IN TEST
26
27
28
29
30
31
40
41
42
43
44
45
dd/dd tt:tt ql ACCT aaaa ANALOG RESTORE
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa FIRE TBL RESTOR
+++ ACCT aaaa AREA=1 POINT=zzz
dd/dd tt:tt ql ACCT aaaa WALK TEST START
+++ ACCT aaaa AREA=1 ID=uuu
SYSTEM IN TEST RESTORE
SILENCE
dd/dd tt:tt ql ACCT aaaa WALK TEST END
+++ ACCT aaaa AREA=1 ID=uuu
dd/dd tt:tt ql ACCT aaaa SENSOR RESET
+++ ACCT aaaa AREA=0 ID=uuu RELAY#=0
FIRE DRILL
dd/dd tt:tt ql ACCT aaaa FIRE WALK START
+++ ACCT aaaa AREA=1 ID=uuu
FIRE DRILL RESTORE
dd/dd tt:tt ql ACCT aaaa FIRE WALK END
+++ ACCT aaaa AREA=1 ID=uuu
SYSTEM RESET
dd/dd tt:tt ql ACCT aaaa SENSOR RESET
+++ ACCT aaaa AREA=1 ID=uuu RELAY#=0
LOW BATTERY
46
47
48
49
50
51
52
dd/dd tt:tt ql ACCT aaaa BATTERY LOW
dd/dd tt:tt ql ACCT aaaa BATTERY RESTORE
dd/dd tt:tt ql ACCT aaaa AC FAILURE
dd/dd tt:tt ql ACCT aaaa AC RESTORAL
dd/dd tt:tt ql ACCT aaaa TEST REPORT
dd/dd tt:tt ql ACCT aaaa TEST-OFF NORMAL
LOW BATTERY RESTORE
AC FAIL
AC FAIL RESTORE
AUTO TEST
OFF NORMAL AT TEST
PHONE 1 TROUBLE
dd/dd tt:tt ql ACCT aaaa PHONE LINE FAIL
+++ ACCT aaaa PHONE LINE=1
PHONE 1 RESTORE
PHONE 2 TROUBLE
53
54
dd/dd tt:tt ql ACCT aaaa PHONE RESTORAL
+++ ACCT aaaa PHONE LINE=1
dd/dd tt:tt ql ACCT aaaa PHONE LINE FAIL
+++ ACCT aaaa PHONE LINE=2
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
108 en | Appendices
Fire Alarm Control Panels
Report
Index
Receiver output
PHONE 2 RESTORE
55
dd/dd tt:tt ql ACCT aaaa PHONE RESTORAL
+++ ACCT aaaa PHONE LINE=2
SYSTEM TROUBLE
56
57
dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=ccc
SYSTEM TROUBLE RESTORE
dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL
+++ ACCT aaaa SDI=001 COND=ccc
MANUAL TEST
DATA LOST
58
59
dd/dd tt:tt ql ACCT aaaa TEST REPORT
dd/dd tt:tt ql ACCT aaaa COMM FAIL
+++ ACCT aaaa PHONE#=1
EEPROM FAILURE
60
61
62
63
dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=18
EEPROM RESTORAL
SMOKE POWER FAULT
SMOKE POWER RESTORE
dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL
+++ ACCT aaaa SDI=001 COND=18
dd/dd tt:tt ql ACCT aaaa EQUIPMENT FAIL
+++ ACCT aaaa SDI=001 COND=3
dd/dd tt:tt ql ACCT aaaa EQUIP RESTORAL
+++ ACCT aaaa SDI=001 COND=3
REMOTE PROGRAMMING FAIL
66
67
dd/dd tt:tt ql ACCT aaaa RAM ACCESS FAIL
dd/dd tt:tt ql ACCT aaaa RAM ACCESS OK
REMOTE PROGRAMMING SUCCESS
Notes:
dd/dd tt:tt: date and time
aaaa: account number
ccc: numeric identifier
uuu: user ID
zzz: point
Table 10.4: Modem 111a2 reporting
The following table provides event numbers and their condition as they appear in the history
log.
Condition
System
event
Condition
System
event
Option bus device at address 1 failed
Option bus device at address 2 failed
2
Remote relay module 2 disabled by
user
52
3
Class A, Style 6 wiring failure on MUX
bus
53
Option bus device at address 3 failed
Option bus device at address 4 failed
Option bus device at address 5 failed
Option bus device at address 6 failed
4
5
6
7
MUX bus A (9-128) failed
54
55
56
MUX bus B (129-255) failed
MUX module processor failure
Remote NAC module 1, output 1 wiring 57
fault
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 109
Condition
System
event
Condition
System
event
Option bus device at address 7 failed
Option bus device at address 8 failed
Option bus device at address 9 failed
8
Remote NAC module 1, output 2 wiring 58
fault
9
Remote NAC module 1, output 3 wiring 59
fault
10
Remote NAC module 1, output 4 wiring 60
fault
Option bus device at address 10 failed 11
Option bus device at address 11 failed 12
Option bus device at address 12 failed 13
Option bus device at address 13 failed 14
Option bus device at address 14 failed 15
MUX bus A (9-128) hardware failure
61
MUX bus B (129-255) hardware failure 62
NAC 1 disabled by user
NAC 2 disabled by user
63
64
Remote NAC module 2, output 1 wiring 65
fault
Option bus device at address 15 failed 16
Remote NAC module 2, output 2 wiring 66
fault
IP communication failed
17
18
19
20
21
22
23
24
25
26
27
28
Remote NAC module 2, output 3 wiring 67
fault
Communication fault (Restoral data
lost)
Remote NAC module 2, output 4 wiring 68
fault
EEPROM failure
Remote NAC module 3, output 1 wiring 69
fault
Battery charger failure
Remote NAC module 3, output 2 wiring 70
fault
Ground fault- wiring short
NAC 1 open wiring
Remote NAC module 3, output 3 wiring 71
fault
Remote NAC module 3, output 4 wiring 72
fault
NAC 2 open wiring
Remote NAC module 4, output 1 wiring 73
fault
Remote NAC module 1 AC failure
Remote NAC module 2 AC failure
Remote NAC module 3 AC failure
Remote NAC module 4 AC failure
Remote NAC module 4, output 2 wiring 74
fault
Remote NAC module 4, output 3 wiring 75
fault
Remote NAC module 4, output 4 wiring 76
fault
Remote NAC module 1, output 1
disabled by user
77
NAC 1 shorted wiring
Remote NAC module 1, output 2
disabled by user
78
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
110 en | Appendices
Fire Alarm Control Panels
Condition
System
event
Condition
System
event
NAC 2 shorted wiring
29
30
31
32
33
34
35
36
37
38
39
40
Remote NAC module 1, output 3
disabled by user
79
80
81
82
83
84
85
86
87
88
89
90
91
92
Remote NAC module 1 ground fault-
short
Remote NAC module 1, output 4
disabled by user
Remote NAC module 2 ground fault-
short
Remote NAC module 2, output 1
disabled by user
Remote NAC module 3 ground fault-
short
Remote NAC module 2, output 2
disabled by user
Remote NAC module 4 ground fault-
short
Remote NAC module 2, output 3
disabled by user
NAC 1 overcurrent
Remote NAC module 2, output 4
disabled by user
NAC 2 overcurrent
Remote NAC module 3, output 1
disabled by user
Remote NAC module 1 low battery
Remote NAC module 2 low battery
Remote NAC module 3 low battery
Remote NAC module 4 low battery
Communication path IP #1 fault
Remote NAC module 3, output 2
disabled by user
Remote NAC module 3, output 3
disabled by user
Remote NAC module 3, output 4
disabled by user
Remote NAC module 4, output 1
disabled by user
Remote NAC module 4, output 2
disabled by user
Multiplex bus outputs disabled by user 46
Remote NAC module 4, output 3
disabled by user
Dialer disabled by user
47
Remote NAC module 4, output 4
disabled by user
Relay 1 disabled by user
Relay 2 disabled by user
48
49
Four zone expander installation fault
93
94
MUX (DS9341) expander installation
fault
Relay 3 disabled by user
50
Communication path IP #2 fault
95
Remote relay module 1 disabled by user 51
Table 10.5: History log
10.4
Appendix D: Programming Defaults List
For program default settings, see the following tables:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 111
PROG TIME
SYSTEM:
Last date in EE 0000
AUTO TEST
TEST TIME:
TEST FREQ:
DAYLIGHT SAV:
SECURITY
0200
3 hr to 24 hr
2- enable
PINS
PROGRAMMER:
USERS:
9876
User 1 = 1234
User 2 = 0000
AUTHORITY
USER 1:
2
0
OTHERS:
PROG SYSTEM
TIMERS
SMOKE RESET:
AC FAIL DELAY:
AUTO SILENCE:
DISPLAY RATE:
AC LINE SYNCH
OPTION BUS
UPDATE BUS:
6 sec
6 hr
0 min
4x.25 = 1 sec
2 (60 Hz)
Queries option buses and updates list of
connected devices.
SETUP KEYPAD:
PIN REQUIRED:
LOCAL:
0
0- No
REMOTE:
1- Yes
REMOTE PGM
PROG INPUTS
0- disable
POINT NUMBER
FUNCTION
(1-4/5-8/9-255)
Point Function 1 = 1
Point Function 2 = 2
Point Function 3 = 3
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
112 en | Appendices
Fire Alarm Control Panels
Point Function 4 = 4
Point Function 5 = 5
Point Function 6 = 6
Point Function 7 = 7
Point Function 8 = 8
Point Function 9 - 255 = 10
Trouble On Open
Point Zone 1 = 1
Point Zone 2 = 2
Point Zone 3 = 3
Point Zone 4 = 4
Point Zone 5 = 5
Point Zone 6 = 6
Point Zone 7 = 7
Point Zone 8 = 8
Point Zone 9 - 19 = 9
Point Zone 20 - 39 = 10
Point Zone 40 - 59 = 11 etc.
No
ALARM/TROUBLE:
OUTPUT ZONE
VERIFICATION:
LATCHING:
Yes
POINT FUNCTION (1-16)
1-3, 5-10, 12-16
4
11
CONFIGURE
fire
no
water
no
supv
no
LOCAL ONLY
SILENCEABLE
LOOP REPSONSE
PROG OUTPUTS
no
no
no
fast
16s
fast
NACs
NAC #1:
CONFIGURATION:
ZONE ASSIGNS:
Zone A:
Steady
53
61
0
Zone B:
Zone C:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 113
NACs
Zone D:
0
NAC #2:
CONFIGURATION:
ZONE ASSIGNS:
Zone A:
Steady
53
61
0
Zone B:
Zone C:
Zone D:
0
RNACs
RNAC 1
Outputs 1, 2, 3, 4
Configuration:
Zone Assignment:
Zone A:
Steady
53
0
Zone B:
Zone C:
0
Zone D:
0
RNAC 2
Outputs 1, 2, 3, 4
Configuration:
Zone Assignment:
Zone A:
Steady
53
0
Zone B:
Zone C:
0
Zone D:
0
RNAC 3
Outputs 1, 2, 3, 4
Configuration:
Zone Assignment:
Zone A:
Steady
53
0
Zone B:
Zone C:
0
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
114 en | Appendices
Fire Alarm Control Panels
RNACs
Zone D:
0
RNAC 3
Outputs 1, 2, 3, 4
Configuration:
Zone Assignment
Zone A:
Steady
53
0
Zone B:
Zone C:
0
Zone D:
0
RELAYS
LOCAL:
RELAY #1
Zone A:
Zone B:
Zone C:
Zone D:
RELAY #2
Zone A:
Zone B:
Zone C:
Zone D:
RELAY #3
Zone A:
Zone B:
Zone C:
Zone D:
63
0
0
0
62
0
0
0
58
0
0
0
REMOTE
REMOTE 1 (D7035)
Relay 1 / Zone A:
Relay 2 / Zone A:
Relay 3 / Zone A:
Relay 4 / Zone A:
63
62
61
60
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 115
REMOTE
Relay 5 / Zone A:
Relay 6 / Zone A:
Relay 7 / Zone A:
Relay 8 / Zone A:
REMOTE 2
58
57
56
53
Relay 1 / Zone A:
Relay 2 / Zone A:
Relay 3 / Zone A:
Relay 4 / Zone A:
Relay 5 / Zone A:
Relay 6 / Zone A:
Relay 7 / Zone A:
Relay 8 / Zone A:
1
2
3
4
5
6
7
8
PROG ACCOUNTS
PHONE NUMBERS
PHONE 1, 2
NUMBER/IP:
FORMAT:
> (wait for dialtone)
0 - Disable
ACCT NUMS:
TONE:
0000
1 – 19D, 14A, 10PS
PHONE CONTROL
LINE 1, 2
MONITOR:
No
DIALING TYPE:
REPORT STEERING
Pulse Only
ALL SUB-MENU ITEMS:
RING COUNT:
Phone 2 Back-up
00
10
No
0
COMM TRIES:
MACH BYPASS:
ALTER COMM
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
116 en | Appendices
Fire Alarm Control Panels
PROG FORMATS
4/2 ZONE REPORT
0 - FIRE ALRM D1:
1 - FIRE RSTR D1:
2 - WATERFLOW D1:
3 - SUPERVISE D1:
4 - TROUBLE D1:
5 - TRBL RSTR D1:
6 - DISABLE D1:
7 - DSBL RSTR D1:
8 - MORE
0
3
0
0
6
3
B
3
1 - POINT 1 D2:
2 - POINT 2 D2:
3 - POINT 3 D2:
4 - POINT 4 D2:
5 - POINT 5 D2:
6 - POINT 6 D2:
7 - POINT 7 D2:
8 - POINT 8 D2:
1 - POINT 9 D2:
2 - POINT 10 D2:
1
2
3
4
5
6
7
8
9
0
ALT 4/2 CODES
SYSTM IN TST:
SYS TEST RST:
SILENCE:
33
37
9F
33
37
9F
69
79
60
70
FIRE DRILL:
FIRE DRL RST:
OPEN RST RPT:
LOW BATTERY:
LOW BATT RST:
AC FAILURE:
AC FAIL RST:
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 117
ALT 4/2 CODES
TEST REPORT:
OFF NORM TST:
PHONE 1 TRBL:
PN 1 TRB RST:
PHONE 2 TRBL
PN 2 TRB RST:
SYSTEM TROUB:
SYS TRB RST:
30
33
31
35
32
36
33
37
BFSK RPT CDS
OFF NRM TST:
OPEN/RESET:
SILENCE:
FD
FD
FD
FD
ED
FIRE DRILL:
FIR DRIL RSTR:
HISTORY DEFAULTS
ALT 4/2 CODES
4/2 POINT REPORTS
FIRE ALRM D1:
FIRE RSTR D1:
WATERFLOW D1:
SUPERVISE D1:
TROUBLE D1:
TRBL RSTR D1:
DISABLE D1:
0
2
0
0
6
7
5
2
0
1
2
3
4
5
DSBL RSTR D1:
MONITOR D1
POINT 1 D2:
POINT 2 D2:
POINT 3 D2:
POINT 4 D2:
POINT 5 D2:
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
118 en | Appendices
Fire Alarm Control Panels
4/2 POINT REPORTS
POINT 6 D2:
6
7
8
9
0
POINT 7 D2:
POINT 8 D2:
POINT 9 D2:
POINT 10 D2:
4/2 RPT CODS
SYSTM IN TST:
SYS TEST RST:
SILENCE:
33
37
9F
33
37
9F
69
79
60
70
30
33
31
35
32
36
33
37
FIRE DRILL:
FIRE DRL RST:
OPEN RST RPT:
LOW BATTERY:
LOW BATT RST:
AC FAILURE:
AC FAIL RST:
TEST REPORT:
OFF NORM TST:
PHONE 1 TRBL:
PN 1 TRB RST:
PHONE 2 TRBL
PN 2 TRB RST:
SYSTEM TROUB:
SYS TRB RST:
Multiplex
MUX BUS TYPE:
2 CLASS B
10.5
Appendix E: Phone Monitor Troubleshooting
10.5.1
COMM FLT/DATA LOST
A common cause of this fault condition is failing to program Phone/IP Number 2 or Account
Number 2 while some reports are directed to Phone/IP 2 Backup reports are still made to
Phone/IP Number 1. This message warns the installer that Phone/IP Number 2 is not available
if it is needed.
2012.08 | 04 | F01U008458
Installation and Operation Manual
Bosch Security System, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
Fire Alarm Control Panels
Appendices | en 119
Other communications problems that can cause this condition include:
1. Events occurring faster than the dialer can send them, which overflows the 32 event
buffer,
2. Programming errors such as missing phone numbers or account codes, over 100 Trouble
reports in 24 hours, or
3. Other problems contacting a receiver.
Check dialing type, format selection, phone numbers, account codes, phone line condition and
tone programming (if tone burst formats are used).
10.5.2
Trouble Phone
Some troubleshooting tips for phone monitor problems are listed below:
Warning!
High voltage!
!
The voltage present during ringing for an incoming call can be over 100 VAC.
1. Use a voltmeter to measure the voltage present across each phone line (Tip to Ring)
while the phone line is idle. This standby telco battery voltage is typically in the range of
30 VDC to 50 VDC, but any voltage above 5 VDC is accepted by the control panel. The
polarity of the voltage does not matter.
2. Check for other devices that might use the phone line, such as fax machines, credit card
verifiers or PBX systems. If the devices cannot be removed, ensure they are wired so that
the control panel’s line seizure relay disconnects them when needed. Measure the line
voltage while these devices are in use. Ensure that it stays above 5 V.
Notice!
NFPA 72 requirements mandate a dedicated phone line for fire reporting.
3. Check for intermittent faults in the phone line. Make a test call and confirm that the line
is free of distortion and noise. Temporarily swap Lines 1 and 2 on the control panel and
check if the problem indication moves to the control panel’s other phone line channel. If
so, the phone line is causing the problem rather than the line monitor.
4. Confirm that the fault message is phone fault and not com fault. Com fault is often
caused by failing to program a phone number or account number for Phone Number 2
while routing reports to Line 1, Backup Line 2. If only one phone number is available for
reporting, set report direction for all events to phone 1 only. Com fault can also happen if
one of the phone lines has telco battery voltage, but does not complete a call. Make test
calls to the receiver(s) on both phone lines, listening for the receiver ACK tone.
5. Ensure that two phone lines are available. In accordance with NFPA requirements, the
Auto-test report is sent on a different phone line each time it is sent. If only one phone
line is connected to the control panel, a Com fault is generated on every other test call.
Bosch Security System, Inc.
Installation and Operation Manual
2012.08 | 04 | F01U008458
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY, 14450
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2012
Download from Www.Somanuals.com. All Manuals Search And Download.
|