GV2 Series Control Panels
Owner's Manual
EN Supplement
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
Contents
1.0
Introduction....................................................................... 5
2.0
2.1
General Commands........................................................... 5
Two-Man Rule............................................................................ 5
2.1.1 Description................................................................................. 5
2.1.2 Using the Two-Man Rule ........................................................... 5
2.2
Early Ambush ............................................................................ 6
2.2.1 Description................................................................................. 6
2.2.2 Using Early Ambush .................................................................. 6
2.3
Easy Exit Control ....................................................................... 7
2.3.1 Description................................................................................. 7
2.3.2 Using Easy Exit Control............................................................. 7
2.4
Passcode Follows Scope........................................................... 8
2.4.1 Description................................................................................. 8
2.4.2 Using Passcode Follows Scope ................................................ 8
2.5
Passcode-Controlled Menu ....................................................... 9
2.5.1 Description................................................................................. 9
2.5.2 Using Passcode Controlled Menus............................................ 9
2.6
Walk Tests ............................................................................... 10
2.6.1 Description............................................................................... 10
2.6.2 Using Walk Test....................................................................... 10
2.7
Door Activated Custom Function............................................. 12
2.7.1 Description............................................................................... 12
2.7.2 Using Door Activated Custom Functions:................................ 12
2.8
Access Level Control............................................................... 13
2.8.1 Description............................................................................... 13
2.8.2 Using ACCESS LEVEL CTL?.................................................. 13
2.9
Door Control ............................................................................ 14
2.9.1 Description............................................................................... 14
2.9.2 Using Door Control?........................................................... 14
2.9.3 Cycle Door?......................................................................... 15
2.9.4 Unlock Door?....................................................................... 16
2.9.5 Secure Door?....................................................................... 16
2.10
Delete User [COMMAND 53]................................................... 18
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.10.1 Description ............................................................................... 18
2.10.2 Using DEL USER ?................................................................. 18
2.11
Add/Change User - [COMMAND 56] ....................................... 19
2.11.1 Description ............................................................................... 19
2.11.2 Using Add User ?................................................................. 19
3.0
3.1
3.2
3.3
SIA CP-01 Compliance Information.................................22
System Requirements.............................................................. 22
False Alarm Reduction Features.............................................. 22
User-Caused False Alarms, Arming the System...................... 23
3.3.1 Exit Time Defaults.................................................................... 23
3.3.2 Exit Tone.................................................................................. 23
3.3.3 Exit Time Restart...................................................................... 23
3.3.4 Exit Error .................................................................................. 23
3.3.5 Master Arm − No Exit Feature (Unvacated Premises)............. 24
3.3.6 Recent Closing......................................................................... 24
3.4
User-Caused False Alarms, Disarming the System................. 24
3.4.1 Entry Time Defaults.................................................................. 24
3.4.2 Passcode Disarms System (Area) ........................................... 24
3.5
3.6
Arming and Disarming with Keyswitches ................................. 25
Alarm Transmission Sequence – Alarm Abort......................... 25
3.6.2 Abort Window........................................................................... 25
3.6.3 Passcode Acknowledges Alarm............................................... 25
3.6.4 Alarms Acknowledged within the Abort Window...................... 26
3.6.5 At the End of the Alarm Abort Window..................................... 26
3.7
3.8
Cancel Report and Cancel Window......................................... 26
Duress Alarm ........................................................................... 26
Tables
Table 1:
Table 2:
Table 3:
Table 4:
Walk Test Menu Access....................................................10
Hardware States of Points.................................................11
Key to Symbols..................................................................15
System Requirements .......................................................22
4
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
1.0 Introduction
This document supplements the Security System Owner’s Manual
(P/N: 71-06633-000) with the features for the GV2 Series. The
instructions for the commands listed in this document replace
those commands in the Security System Owner’s Manual. Refer to
the Owner’s Manual for the operation of your new security system
and its other basic features.
Place this supplement inside the Security System Owner’s
Manual.
2.0 General Commands
2.1 Two-Man Rule
2.1.1 Description
The Two-Man Rule adds an extra step to the disarming process by
requiring two unique passcodes to disarm an area from the same
keypad.
I have this feature.
I do not have this feature.
2.1.2 Using the Two-Man Rule
1. Ensure that the keypad shows idle armed text or Disarm Now.
2. Enter a valid passcode with the authority to Passcode Disarm
by pressing the [passcode digits] followed by the [ENTER] key
(D1260) or [ENT] key (D1255).
3. The keypad shows a request for the SECOND CODE:
4. Enter a second valid passcode with the authority to Passcode
Disarm by pressing the [passcode digits] followed by the
[ENTER] or [ENT] key. The second passcode must be different
from the first passcode.
The area is disarmed and ready for entry.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
5
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.2 Early Ambush
2.2.1 Description
Early Ambush adds an extra step to the disarming process by
requiring the entry of an additional passcode to confirm that the
area is secure. The second passcode can be same as the first or
different, depending upon the configuration. The first entry
disarms the area and the second entry stops an automatic timer
from sending a duress event.
I have this feature.
I do not have this feature.
2.2.2 Using Early Ambush
1. Ensure that the keypad shows idle armed text or Disarm Now.
2. Enter a valid passcode with the authority to Passcode Disarm
by pressing the [passcode digits] followed by the [ENTER] key
(D1260) or [ENT] key (D1255).
3. Ensure that the keypad shows idle disarmed text.
4. You can now search the area; however, you must enter the
second passcode before the preset Early Ambush Time
expires.
5. Enter a second valid passcode with the authority to Passcode
Disarm by pressing the [passcode digits] followed by the
[ENTER] or [ENT]key.
6. The keypad shows CODE 2 VALIDATEDto confirm that the
second passcode is accepted and the Early Ambush Window is
canceled.
The area is disarmed and ready for entry.
6
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.3 Easy Exit Control
2.3.1 Description
The GV2 Series control panels change from one armed state to
another armed state without disarming. The Easy Exit Control
feature decreases the number of keystrokes and simplifies system
operation. This feature is available by default and is always on.
2.3.2 Using Easy Exit Control
Switching armed states from Master to Perimeter:
1. Ensure that the keypad shows idle master armed text.
2. Press the [COMMAND] key. The keypad shows SYSTEM
COMMAND.
3. Press [3] to Perimeter Arm.
4. The keypad display shows the Exit Delay countdown.
5. Enter or exit from the premises.
Switching armed states from Perimeter to Master:
1. Ensure that the keypad shows idle perimeter armed text.
2. Press the [COMMAND] key. The keypad shows SYSTEM
COMMAND.
3. Press [1] to Master Arm.
4. The keypad shows the Exit Delay countdown.
5. Enter or exit from the premises.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
7
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.4 Passcode Follows Scope
2.4.1 Description
The Passcode Follows Scope feature is an optional arming and
disarming restriction that can be enabled on keypads with access
to multiple areas. When this feature is set to No, the keypad
restricts Passcode Arming and Passcode Disarming to the home
area of the keypad. When set to Yes, this feature allows users to
arm or disarm all the areas to which they and the keypad have
access. This feature causes no restrictions to the keypad scope as
it pertains to any command or arming method other than
Passcode Arming or Passcode Disarming.
I have this feature.
I do not have this feature.
2.4.2 Using Passcode Follows Scope
Arming from a keypad with Panel Wide scope and Passcode
Follows Scope enabled:
1. Ensure that the keypad shows idle disarmed text.
2. Ensure that you have a valid passcode with the authority to
Passcode Arm in all areas.
3. Enter your passcode by pressing the [passcode digits]
followed by the [ENTER] key (D1260) or [ENT] key (D1255).
4. The keypad shows ARMING: 12345678to indicate which areas
are ready to enter exit delay and arm.
5. The keypad shows the exit delay countdown.
6. Exit from the premises.
Arming from a keypad with Panel Wide scope and Passcode
Follows Scope disabled (default):
1. Ensure that the keypad shows idle disarmed text.
2. Ensure that you have a valid passcode with the authority to
Passcode Arm in all areas.
3. Enter your passcode by pressing the [passcode digits]
followed by the [ENTER] key (D1260) or [ENT] key (D1255).
4. The keypad shows the exit delay countdown.
5. Exit from the premises.
8
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.5 Passcode-Controlled Menu
2.5.1 Description
When enabled, the system prompts users to enter a passcode
before viewing the keypad menu. The system shows the user the
menu options allowed according to their authority level, thereby
providing users only pertinent commands and functions.
I have this feature.
I do not have this feature.
2.5.2 Using Passcode Controlled Menus
On a D1255 Keypad with the Passcode Controlled Menu enabled:
1. Press the [ESC] key. The keypad shows ENTER PASSCODE.
2. Enter your passcode by pressing the [passcode digits]
followed by the [ENT] key. The first menu item for which you
have authority appears.
On a D1260 Keypad with the Passcode Controlled Menu enabled:
1. Press the [Menu>] soft key in the lower right corner. The
keypad responds with Enter passcode: then press [ENTER]
display.
2. Enter your passcode by pressing the [passcode digits]
followed by the [ENTER] key.
The first and second menu items for which you have authority
appear.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.6 Walk Tests
2.6.1 Description
The D9412GV2, D7412GV2, and D7212GV2 have three Walk Test
menus that allow the user to test various points that are within
the scope of the keypad without sending a report to the central
station.
Test each smoke detector according to the manufacturer’s
instructions.
Table 1: Walk Test Menu Access
Test Type
Command
Sequence
Menu Function Name
Point Types
Tested
WALK TEST ?
Walk
[COMMAND][4][4]
Visible
Perimeter and
Interior
FIRE TEST ?
Fire
[COMMAND][5][8]
Not applicable
Fire and 24-
hour
INVISIBLE TEST ?
Invisible
Invisible
Perimeter and
Interior
I have this feature.
I do not have this feature.
2.6.2 Using Walk Test
On a D1255 Keypad:
1. If you use the command sequence, press the keys shown in
the Command Sequence column of Table 1 for the necessary
test. The keypad shows the number of testable points within
the scope of the keypad: ### PTS TO TEST. Proceed to Step
5.
2. If you use menu function list, press the [ESC] key.
3. Press the [NEXT] key until the Menu Function Name (refer to
Table 1) appears.
10
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
4. Press the [ENT] key to activate the selected walk test function.
The keypad shows the number of testable points within the
scope of the keypad: ### PTS TO TEST
5. Press the [NEXT] key to see VIEW UNTESTED?
6. Press the [ENT] key to view the untested points. The keypad
shows the total number of untested points within the keypad
scope: ### PTS UNTESTED.
7. Press the [NEXT] key to view the first point’s name.
8. Press the [ENT] key to view the point’s hardware state. Refer
to Table 2.
Table 2: Hardware States of Points
Display Text
Hardware State
Normal
1PT### NORMAL HW
1PT### OPEN HW
1PT### SHORT HW
1PT### MISSNG HW
Opened
Shorted
Missing
9. Activate the point’s sensor and observe the appropriate state
change.
10. Press the [NEXT] key to advance to the next untested point
within the scope of the keypad.
11. Repeat steps 8 through 10 until all points are tested.
On a D1260 Keypad:
1. If you use the command sequence, press the keys indicated in
the Command Sequence column of Table 1 on page 10 for the
necessary walk test. The keypad shows the number of testable
points within the scope of the keypad: ### pointsremain
to be tested. Proceed to Step 5.
2. If you use the menu function list, press the [Menu>] soft key in
the lower right corner.
3. Press the [Next >] soft key until the Menu Function Name
(refer to Table 1 on page 10) appears.
4. Press the corresponding soft key to activate the necessary
Walk Test functions.
The keypad shows the number of testable points within the
scope of the keypad: ### pointsremain to be tested.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
5. Press the [View untested Pts >] soft key to see ### PTS
UNTESTED.
6. Press the [Next Pt >] soft key to view the first or next
untested point:
[Point Text]
Area #, Pt #
[Point State] HW
<Exit
Next PT>
Prev PT>
The point state can be NORMAL, OPEN, SHORT, or MISSING.
7. Activate the point’s sensor and observe the state change.
8. Repeat Steps 5 through 7 until all points are tested.
2.7 Door Activated Custom Function
2.7.1 Description
The D9412GV2 and D7412GV2 allow a custom function to be
activated when user credentials are presented to a D9210B Door
Controller Reader. The custom function executes as if the user
performed a function at the keypad that is associated with the
door controller.
I have this feature.
I do not have this feature.
2.7.2 Using Door Activated Custom Functions:
Executing the door’s custom function by a user that has authority
to do so when disarming the area:
1. Ensure that the area you are about to enter is armed.
2. Present your user credentials to the D9210B Door Controller
Reader. The area disarms and the custom function executes.
The area is now safe to enter.
12
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.8 Access Level Control
2.8.1 Description
Use this function to manually enable or disable access authority
levels assigned to users. This function can be used to disable a
user’s access level temporarily instead of deleting and adding the
user.
I have this feature.
I do not have this feature.
2.8.2 Using ACCESS LEVEL CTL?
On a D1255 Keypad
1. Activate the door’s custom functions. Refer to Section 2.7.2
Using Door Activated Custom Functions on page 12.
2. Ensure that the display shows idle disarmed text.
3. Press the [MENU] key to enter the function list, then press
[NEXT] repeatedly until you reach the CHANGE LEVEL CTL?
prompt. Press [ENT].
4. ACCESS LEVEL CTLappears, indicating that you are affecting
the authority levels of cards or tokens and not passcodes.
Press [ENT].
5. ENTER LEVEL:appears. Enter the access authority level
number and press [ENT].
6. If the access level is currently disabled, LEVEL # ENABLE?
appears. If the access level is currently enabled, LEVEL #
DISABLE?appears. Press [ENT] to accept the choice.
7. ENTER LEVEL:appears again. Press [ESC].
On a D1260 Keypad
1. Activate the door’s custom functions. Refer to Section 2.7.2
Using Door Activated Custom Functions on page 12.
2. Ensure that the display shows idle disarmed text.
3. Press the [Menu>] soft key to enter the function list. Then
press [Next>] repeatedly until you reach the CHANGE LEVEL ?
prompt.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
4. Press the [Change Level ? >] soft key. ACCESS LEVEL CTL
appears, indicating that you are affecting the authority levels
of cards or tokens and not passcodes.
5. ENTER LEVEL:appears. Enter the access authority level
number and press [ENTER].
6. If the access level is currently disabled, LEVEL # ENABLE?
appears. If the access level is currently enabled, LEVEL #
DISABLE?appears. Press [ENTER] to accept the choice.
7. Repeat Steps 5 and 6 as necessary.
2.9 Door Control
2.9.1 Description
The door control function has three sub-functions:
• CYCLE DOOR?
• UNLOCK DOOR?
• SECURE DOOR?
CYCLE DOOR?unlocks a door briefly to allow a person into an
area.
UNLOCK DOOR?unlocks a door to allow free access.
SECURE DOOR?locks a door and prohibits access regardless of a
user’s authority level.
I have this feature.
I do not have this feature.
2.9.2 Using Door Control?
On a D1255 Keypad
1. Ensure that the display shows idle disarmed text.
2. Press the [COMMAND] key. The display shows SYSTEM
COMMAND.
3. Press [4] and [6].
You can use the function list in place of steps 2 and 3 to
start this function.
4. Press the [MENU] key to enter the function list.
5. Press [NEXT] repeatedly until you reach the DOOR
CTRL?prompt.
6. Press [ENT].
14
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
7. The first sub-function that appears is CYCLE DOOR?. You can
cycle through the three sub-functions by pressing [PREV] and
[NEXT].
On a D1260 Keypad
1. Ensure that the display shows idle disarmed text.
2. Press the [COMMAND] key. The display shows SYSTEM
COMMAND.
3. Press [4] and [6].
You can use the function list in place of steps 2 and 3 to
start this function.
1. Press the [Menu>] soft key to enter the function list.
2. Press [Next>] repeatedly until you reach the DOOR
CTRL?prompt.
3. Press the [Door Control ? >] soft key.
4. All authorized door control function sub-functions are listed.
Press the corresponding soft key to enter the sub-function.
2.9.3 Cycle Door?
1. To unlock an access door briefly and allow a person into an
area, press [ENT] at the Cycle Door?prompt.
The display shows CYCLE 1 2 3 4 5 6 7 8if all doors are in
a normal state and available. If a door is not in a normal state,
the number of the door is replaced with one of the symbols
indicated in Table 3.
Table 3: Key to Symbols
Symbol
---
Description
Door is not active, not in scope, or user does not have
access level authority
C
U
X
P
Door is timed door sequence
Strike and shunt are latched active (held open)
Strike and shunt are deactivated (secured)
There is a problem with the door; call your security
company
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
15
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2. Enter the number of the door to cycle then press [ENT]. This
door cycles and the display changes to reflect the new status
of the doors. For example, to cycle Door 3, at the
CYCLE DOOR 1 2 3 4 5 6 7 8prompt, press [3], then press
[ENT]. The display shows CYCLE DOOR 1 2 C 4 5 6 7 8.
This indicates that all doors are in a normal state, except for
Door 3, which is cycled.
3. Press [ESC] to leave this sub-function, or enter another door
number to cycle.
2.9.4 Unlock Door?
1. To unlock a door to allow free access, at the CYCLE DOOR?
prompt, press [NEXT] to enter the UNLOCK DOOR?sub-
function.
2. The display shows UNLOCK 1 2 3 4 5 6 7 8if all doors are
in a normal state and available. If a door is not in a normal
state, the number of the door is replaced with a symbol
indicated in Table 3 on page 15.
3. Enter the number of the door to unlock then press [ENT]. This
door unlocks and the display changes to reflect the new status
of the doors.
For example, to unlock Door 4, at the following prompt,
press [4], then press [ENT].
UNLOCK DOOR 1 2 3 4 5 6 7 8
The display shows UNLOCK DOOR 1 2 3 U 5 6 7 8
This indicates that all doors are in a normal state, except for
Door 4, which is unlocked.
4. Press [ESC] to leave this sub-function, or enter another door
number to unlock.
2.9.5 Secure Door?
1. To secure a door to prohibit access to users regardless of their
access authority level, at the CYCLE DOOR?prompt, press
[PREV] to enter the SECURE DOOR?sub-function.
2. The display shows SECURE 1 2 3 4 5 6 7 8if all doors are
in a normal state and available. If a door is not in a normal
state, the number of the door is replaced with a symbol
indicated in Table 3 on page 15.
16
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3. Enter the number of the door to secure then press [ENT]. This
door secures, and the display changes to reflect the new
status of the doors.
For example, to secure Door 5, press [5], then press [ENT] at
the following prompt: SECURE DOOR 1 2 3 4 5 6 7 8
The display shows SECURE DOOR 1 2 3 4 X 6 7 8. This
indicates that all doors are in a normal state, except for
Door 5, which is secured.
4. Press [ESC] to leave this sub-function, or enter another door
number to unlock.
Each of these sub-functions acts as a toggle switch. To
return a door to its normal state, follow the same procedure
used to change its state. For example, if Door 3 is secured,
to return it to its normal state, at the SECURE DOOR?
prompt, enter [3] and press [ENT]. The door is no longer
secured and the X is replaced with the number 3.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
17
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.10 Delete User [COMMAND 53]
2.10.1 Description
Use this function to delete a personal passcode from your system
without assistance from your security company. You must know
the user number for the passcode you want to delete.
I have this feature.
I do not have this feature.
2.10.2 Using DEL USER ?
1. Ensure that the display shows idle disarmed text.
2. Press the [COMMAND] key. The display shows SYSTEM
COMMAND.
3. Press [5] and [3].
You can use the function list in place of steps 2 and 3 to
start this function.
1. Press the [MENU] key to enter the function list.
2. Press [NEXT] repeatedly until you reach the DEL
USER?prompt.
3. Press [ENT].
4. The display shows DEL USER #. Enter the user number and
press [ENT].
5. USER ##(or user text, such as the name of the user, if this
feature was programmed into your system by your security
company) appears, allowing for confirmation. Press [ENT].
If this is not the user you wish to delete, press the [NEXT] or
[PREV] key until the correct user name appears, then press
[ENT].
6. The display shows DELETE USER ##?. Press [ENT] to delete
user, and USER DELETEDappears. If the user number is not in
the system, NOT IN USEappears. If you made an error and do
not wish to delete this user, press [ESC].
18
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
2.11 Add/Change User - [COMMAND 56]
2.11.1 Description
Use this function to add or change a passcode or card without
assistance from your security company. Before adding or changing
a passcode or card, you must know which user numbers are
available, the authority level you want to assign to the new user,
and the areas in which the passcode or card are valid.
I have this feature.
I do not have this feature.
2.11.2 Using Add User ?
1. Ensure that the display shows idle disarmed text.
2. Press the [COMMAND] key. The display shows SYSTEM
COMMAND.
3. Press [5] and [6].
You can also use the function list in place of steps 2 and 3
to start this function.
1. Press the [MENU] key to enter the function list.
2. Press [NEXT] until you reach the ADD/CHNG USER?
prompt.
3. Press [ENT].
4. The display shows ENTER USER #. Enter the user number and
press [ENT].
5. The display shows USER # (or user text, such as the name of
the user, if this feature was programmed into your system by
your security company) to allow for confirmation.
Press [ENT] if the correct user number (or user name)
appears. Press [ESC] if not.
6. ADD PASSCODE?appears. (If the user number already exists,
CHANGE PASSCODE?Appears.) Press [ENT].
7. ENTER NEW CODEappears. Enter the new passcode followed
by [ENT]. ENTER AGAINappears.
8. Enter the new passcode a second time for confirmation. Press
[ENT]. The display shows PASSCODE ADDED(or PASSCODE
CHANGEDif the user number was already in the system).
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
19
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
For systems with access control, the following prompts are
available: ADD CARD?, CHANGE CARD?, and SUB USER
ID?. Refer to Systems With Access Control on page 20 for
details.
The system does not accept a passcode that is within two
digits of an existing passcode. This is to avoid conflicts with
duress passcodes. For example, if passcode 123 is already
programmed in the system, the system does not accept
121, 122, 124, or 125 as passcodes.
9. ADD LEVEL?appears. If the user number already exists,
CHANGE LEVEL?appears. Press [ENT].
10. VALID AREA 1? appears. If you wish this user number to be valid
in Area 1, press [ENT]. If not, press [NEXT].
11. AUTH LEVELappears. Assign the authority level you wish the user
number to have for this area and press [ENT]. Record this
information.
12. VALID AREA 2?appears. Enter the information necessary for
the areas in the scope of the keypad by following steps 10 and
11 for each area (up to 8 areas).
13. LEVEL ADDEDor LEVEL CHANGEDappears when all area
assignments are made. Press [ENT].
At the end of each function, press [ESC] to return to the
ENTER USER #prompt. Press [ESC] again to return to idle
text.
Systems With Access Control
If your system includes access control features, such as card
readers at doors, the following prompts can appear during the
ADD USER? procedure.
ADD CARD?(CHANGE CARD?)
1. If the user has card or token access to the building or area,
press [ENT] at the ADD CARD?prompt, or at the CHANGE
CARD?prompt if the user already has a card or token.
2. PRESENT CARDappears. Present the card at the card reader
and wait for the tone.
3. If the reader identifies the card or token correctly, a tone
sounds and the keypad shows CARD ADDED, or CARD CHANGED
if the user already has a card or token. Press [ENT].
20
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
SUB USER ID?
1. At the SUB USER ID?prompt, press [ENT].
2. SUB USER #?appears. Enter 1, 2, or 3 for the desired Sub-
User and press [ENT].
3. PRESENT CARDappears. Present the card or token at the
reader and wait for the tone.
4. After the tone sounds, the display shows CARD ADDED, or CARD
CHANGEDif the Sub User number already existed.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
21
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3.0 SIA CP-01 Compliance Information
Warning: The default programming for the control panel
includes a 30-second communication delay for alarms on
non-fire zone types. It can be removed (or increased to 45
sec) at the option of the end user in consultation with the
installer.
3.1 System Requirements
The minimum system requirements for SIA CP-01 compliance are:
Table 4: System Requirements
Control Panel
D9412GV2
D7412GV2
D7212GV2
Firmware Version
7.05 or later
7.05 or later
7.05 or later
3.2 False Alarm Reduction Features
False alarms are such an issue that the local authorities in some
jurisdictions no longer respond to alarms. The Security Industry
Association (SIA) has developed a Control Panel False Alarm
Reduction Standard that details design features for security
control panels and their associated arming and disarming devices
to reduce the occurrence of false alarms.
This section of the user’s guide supplement will help to explain
proper operation of your SIA CP-01 compliant Bosch Security
Systems, Inc. D9412GV2, D7412GV2, or D7212GV2 Control Panel.
Your installation company must configure all features
necessary to provide SIA CP-01 compliance.
I have this feature.
I do not have this feature.
22
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3.3 User-Caused False Alarms, Arming the System
3.3.1 Exit Time Defaults
The SIA standard calls for Exit Time to range from 45 sec to at
least two min (not to exceed 255 sec).
The default is 60 sec.
3.3.2 Exit Tone
The SIA standard requires that the control panel provide an Exit
Tone to alert anyone remaining in the premises that Exit Delay is
in process. The tone pulsing rate increases during the last 10 sec
of Exit Time.
The Exit Tone can be disabled only for individual keypads, not for
the entire system.
During the last 10 sec of Exit Delay, the control panel’s Alarm Bell
output pulses on and off for the last 10 sec of Exit Delay.
3.3.3 Exit Time Restart
The SIA standard requires that the control have an option that
restarts Exit Delay if a user follows these steps:
1. Starts Exit Delay (arms the system)
2. Exits and closes an Exit Delay zone.
3. Returns through an Exit Delay zone.
4. The control panel restarts Exit Delay (one-time restart only).
I have this feature.
I do not have this feature.
3.3.4 Exit Error
When a user leaves an Exit Delay zone faulted at the end of Exit
Time, the control panel creates an “Exit Error” event as specified
by the SIA standard:
1. An Exit Delay point remains faulted at the end of Exit Delay.
2. Entry Delay starts. Keypads show DISARM NOWand the Entry
Tone sounds.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
23
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3. The user does not return to stop Entry Delay. The Entry Delay
time expires.
4. The control panel starts the alarm transmission sequence,
accompanied by an Exit Error report.
3.3.5 Master Arm − No Exit Feature (Unvacated Premises)
If a user Master Arms an area and does not leave the premises (no
Entry/Exit zones are faulted during the exit time), the control
panel’s No Exit feature automatically shifts the Area from Master
Armed to Perimeter Armed.
I have this feature.
I do not have this feature.
3.3.6 Recent Closing
If an alarm occurs within two min of the expiration of Exit Time,
the control panel creates an “alarm-recent closing” event. If the
user armed with a passcode, the user number is included in the
recent closing report.
Recent Closing events are not created for Fire Alarm events.
3.4 User-Caused False Alarms, Disarming the
System
3.4.1 Entry Time Defaults
The SIA standard requires an Entry Time of between 30 sec and
4 min. The required default is 30 sec. If the system is not
disarmed within Entry Time, the control panel creates an Alarm
Event.
During the Entry Time, the control panel sounds an Entry Delay
Tone (distinct from the alarm tone).
3.4.2 Passcode Disarms System (Area)
When the control panel is in Entry Delay, entering a valid passcode
disarms the system as soon as the last digit of the passcode is
entered. No other keys are required.
When the control panel is in Exit Delay or is armed, entry of a valid
Passcode must be followed by an [ENTER] or [ENT] key.
24
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3.5 Arming and Disarming with Keyswitches
Arming Beeps and Flashes
The SIA standard requires that the control panel provide a means
to annunciate a change in arming state made from a Keyswitch.
The Alarm Bell output pulses on twice when a user disarms with a
remote device. The Alarm Bell output pulses on once when a user
arms with a remote device
3.6 Alarm Transmission Sequence – Alarm Abort
The SIA standard requires an Alarm Abort feature. The control
panel uses this feature to give end users an opportunity to
acknowledge an alarm event and abort the alarm transmission.
The following sections explain how this feature works.
3.6.1 Abort Window
The Abort Window is the time the end user has to acknowledge an
alarm and effectively “abort” the control panel’s alarm response.
The Abort Window is programmable.
•
•
•
The minimum duration is 15 sec.
The maximum duration is 45 sec.
The default is 30 sec.
In accordance with UL standards, the SIA standard intends
that the combined Entry Time and Abort Window will not be
programmed to exceed one minute.
3.6.2 Passcode Acknowledges Alarm
When the control panel is sounding an alarm, enter [passcode] +
[ESC] to silence the alarm without disarming. Entering the first
digit of the passcode temporarily silences the alarm at the keypad.
If a valid passcode is not entered, the alarm begins sounding again
after a period of about 10 sec with no keypad activity.
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
25
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
3.6.3 Alarms Acknowledged within the Abort Window
If the end user acknowledges an alarm within the Abort Window:
•
•
•
The alarm output is silenced.
No alarm, restoral, or cancel reports are sent.
No alarm, restoral, or cancel reports are entered in the control
panel event log.
3.6.4 At the End of the Alarm Abort Window
If no user acknowledges the alarm within the Alarm Abort Window,
the control panel sends the appropriate alarm reports.
3.7 Cancel Report and Cancel Window
If a user acknowledges an alarm after the Abort Window expires,
but before Bell Time expires, the control panel sends a Cancel
Report. The Cancel Window starts when the alarm is sent and
stops when the Alarm Bell timer expires or a user acknowledges
an alarm.
3.8 Duress Alarm
This feature allows any passcode with the Send Duress permission
enabled to always send a Duress Alarm event upon entry. The
Duress Alarm feature allows an installation to allocate unique
passcodes as the main duress passcodes for all users.
Additionally, when the SIA CP-01 compliant Duress Alarm option is
enabled, the Passcode +1 and +2 options are disabled.
26
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
GV2 Series Control Panels | Owner's Manual Supplement
Notes
Bosch Security Systems, Inc. | 2/07 | F01U063791-01
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450-9199
Customer Service: (800) 289-0096
Technical Support: (888) 886-6189
© 2007 Bosch Security Systems
F01U063791-01
Download from Www.Somanuals.com. All Manuals Search And Download.
|