DISHWASHER
Installation
Instructions
Cycle Countdown
Power
Scrub
Plus
Scrub
Wash
Regular
Wash
Delicate/
Econo
Quick
Wash
Rinse
Hold
Refill
Rinse
Agent
On/Off
&
On /Off
High
Temp
Wash
Regular Rinse
Temp
Wash
&
Hold
Power Scrub
Rinse
Hold
Regular
Wash
&
T
op
Delay
Start
Hours
Power
Rack
Only
Temp.Options
Power
Cancel
Drain
Cycles
SHV 6800, 4800,4300
SHI 6800,4300
SHU 9950, 9920, 9910, 8810, 8800, 6800, 5300,
4320,3300, 3131, 3030
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
THESE INSTALLATION INSTRUCTIONS ARE INTENDED
FOR USE BY QUALIFIED INSTALLERS.
In addition to these instructions the dishwasher shall be installed:
•
In the United States, in accordance with the National Electric
Code/State and Municipal codes and/or local codes.
In Canada, in accordance with the Canadian Electric Code
C22.1 -latest edition/Provincial and Municipal codes and/or
local codes.
•
Please read these installation instructions completely and carefully.
They will save you time and effort and help to ensure optimum dishwasher
performance.
Be sure to observe all listed
warnings and cautions. (Look for
WARNING
the triangles with exclamation marks
inside.)
CAUTION
IMPORTANT
•
•
NEW INSTALLATION - If the dishwasher is a new installation, most of the work
must be done before the dishwasher is moved into place.
REPLACEMENT - If the dishwasher is replacing another dishwasher, the
connections for the dishwasher being replaced must be checked for
compatibility with the new dishwasher and replaced as necessary.
INSPECT THE DISHWASHER
After unpacking the dishwasher and prior to installation, thoroughly inspect the
dishwasher for possible freight or cosmetic defect. Report any defect immediately.
Cosmetic defects must be reported within 30 days of installation.
NOTE: Please do not discard any bags or items that come with the
original package until after the entire installation has been completed!
2 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS & MATERIALS NEEDED
Tools Needed for Installation
Hammer
Hole saw or 1” hole cutter
Pipe wrench, 2 reqd.
Tape Measure
Wire Cutter
Slotted screwdriver (#2)
Phillips screwdriver (#2)
Adjustable wrench,
(size med., 2 reqd.)
Torx screwdriver, #20
Level
Wire stripper
Electric Drill
Figure 1
Materials Needed
Electric Connection - 2 conductor, 1 ground
insulated electrical supply cable (30” or
sufficient length for your installation).
1
2
Hot Water Supply Line - Minimum 3/8”
O.D. copper tubing or metal braided
dishwasher supply line.
Shut-off valve and fittings for hot water
supply line.
3
90° elbow with 3/8” N.P.T. external threads
on one end and sized to fit your water
supply line on the other end.
4
Teflon tape or other pipe thread compound
which help seal plumbing connections.
TA
P
E
5
6
7
3 twist-on wire connectors for 16 AWG wire
(need to have metal inserts).
UL listed conduit connector or strain relief.
Additional materials may be required to comply with local codes.
Figure 2
ENGLISH - 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MATERIALS SUPPLIED
Accessory Parts Supplied
Accessory Parts for your model dishwasher
will come in one or more plastic bags. Check
A
to make sure that the parts supplied for your
model are all there. See Figure 3. If any
parts are missing, stop the installation and
contact your dealer immediately.
B
DISHWASHER
C
D
E
INSTALLATION KIT (Clear Bag)
D. Toe Panel Screws (8mm) (2)
E.
F.
Mounting Brackets (1L & 1R)
Mounting Bracket Screws (2)
G. Rubber Connection Hose (1)
and Drain Hose Clamps (2)
F
G
H
SHU 9910, 9920, 8800
and 8810 Models
(excluding 9950 models)
• Dishwasher Installation Kit (1) and
• (Yellow Bag) w/ the following:
A. Hex Wrench 4mm (1)
B. Cover Plugs (2 Wh & 2 Blk) and
R. Door Handle
SHU 6800 Models
• Dishwasher Installation Kit (1) and
• (Green Bag) w/ the following:
I
L.
J-Box Cover (1)
M. J-Box Screw (8mm) (1)
N. Toe Panel Screw (4x16) (2)
O. Base Part Screws (M4x38) (2)
J
SHV and SHI Models
• Dishwasher Installation Kit and
K
L
• Outer Door Installation Kit (Blue bag):
J.
SHI/SHV Panel Installation Template
C. Cap (2 Blk)
K. Wood Screws (2)
I.
M
N
O
Mounting Door Brackets(2 plastic)
w/Screws (4) and;
Mounting Door Brackets (2 metal)
w/Screws (4)
H. Spring Tension Screw (2)
Manual Bag
All Dishwashers come with a manual bag.
The following contents are located in every
bag:
P
Q
R
•
•
Use & Care Manual
Installation Instructions
P. Tall Item Sprinkler (1)
(except SHU 3030 and 3130 models)
SHU 6800 models have an additional part:
Q. Cotton Insulation Strip (1)
Figure 3
Note: Pictures are not to scale.
4 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
CHOOSING A LOCATION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Choosing the Location
Select a location as close to the sink as
possible for ready access to water and drain
lines.
Most of the installation work is done before
the dishwasher is moved into place.
1-15/16” (49mm)
4” (102mm)
Any built-in dishwasher must be fully
enclosed on the top, both sides and back.
Therefore the cabinet space below your
counter is probably the best location.
Figure 4
NOTE: This dimension will vary by model
due to control panel differences.
Overall Dishwasher Dimensions
C
24” (610 mm)
A
B
C
Height
Width
Depth
33 7/8" (860 mm) min.
90°
90°
23 9/16" (598 mm) min.
A
22 7/16" (570 mm) min.
Table 1 – See Figure 4
B
Cabinet Opening Dimensions
23-5/8" - 24-1/8" (600-613 mm)
Figure 5
A
B
C
Height
Width
Depth
34 " (864 mm) min.
23 5/8" (600 mm) min.
24 " (610 mm) min.
Clearance
for door
opening
Table 2 – See Figure 5
Dishwasher
Countertop
For proper operation and appearance of the
dishwasher, the cabinet opening should be
square and have dimensions as shown in
Figure 5.
Door in
open
position
If the dishwasher is to be installed in a
corner, make sure there is adequate clea-
rance to open the door. See Figure 6.
Figure 6
ENGLISH - 5
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUMBING PREPARATION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
CAUTION
To protect against possible rupture of
the fill valve, water lines leading to
the dishwasher, as well as water lines
in the dishwasher MUST be protected
against freezing. If the valve or water
line freezes, flooding may occur. Such
ruptures are not covered by the
warranty.
Drain Hose
The dishwasher comes with a seven (7)
foot drain hose.
• A 1.25” access hole must be made to
allow the drain hose to be run to the
drain connection location.
IMPORTANT
If no air gap is used and the drain
line is run into a sink or disposer,
the drain line must be elevated to
a point higher than the highest
water level of the sink to prevent
Hot Water Supply
•
•
The hot water line to the dishwasher
must provide between 5 - 120 psi (0.3-
8.27 bars) water pressure.
The hot water heater should be set to
deliver 140°F (60°C) water
back
siphoning
into
the
dishwasher.
temperature to the dishwasher.¹
A 3/8” minimum O.D. copper tubing
inlet line is recommended.
All solder connections must be made
before water line is connected to the
dishwasher’s inlet water valve. Do not
solder within 6 inches (152.4 mm)
of the dishwasher’s inlet water
valve.
•
•
NOTE: If connection to an air gap is
required by local code, air gap kits are
available from local plumbing sources.
Install the air gap according to the
manufacturer’s instructions.
•
Drill a 1” (25.4 mm) diameter access
hole in the cabinet for the water supply
line (Figure 9A).
•
Run the line to the approximate fill
valve location, as shown in Figure 9A.
Drain
Hose
It is recommended that a shut-off valve (not
supplied) be installed in the hot water
supply line in a readily accessible location,
see Figure 9.
Hot water
line
Electrical supply cable
Figure 7
1. In order to reduce running time, Bosch recommends 140° F water inlet
temperature. Your dishwasher will perform equally as well at 120° F water
temperature, but the run time will be extended.
6 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL PREPARATION
WARNING
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
23-5/8" - 24-1/8"
(600-613 mm)
3-1/2
(90 mm)
1-5/16
(49 mm)
Electrical Supply
It is the customer’s responsibility to insure
that the dishwasher installation is in
compliance with all national and local
electrical codes and ordinances. The
dishwasher is designed to operate with a
120V, 60Hz, AC only electrical supply.
Connect to a separate electrical circuit with
a fuse or circuit breaker rated for 15 Amps.
A 20 Amp fuse or circuit breaker may be
used if the dishwasher is connected with a
food disposer, but not more than 20 Amps.
Use Copper supply conductors only. The
dishwasher should be properly grounded,
positioned as shown in Figure 9, and should
be installed by a qualified electrician. No
other appliances or outlets should be
connected to this circuit.
Figure 8
Volts Hertz Amperes
1,450
(max)
120
60
15
Table 3
Openings for electrical lines must be
installed in the marked areas as
shown in Figures 8 and 9 to avoid
interference with the dishwasher
frame or other components.
• Cut a 1” (25.4mm) diameter hole in the
cabinet (in area of Figure 9 B). For wood
cabinets, sand the hole until smooth.
For metal cabinets, cover the edge with
a grommet.
Shut-off
valve
A
B
14”
(355 mm)
• Run flexible cable (as codes permit) from
junction through hole in cabinet. Cable
should extend 30” (762 mm) from back
wall.
HWS
21”
(533 mm)
Hot water supply line Electric supply cable
Figure 9
ENGLISH - 7
Download from Www.Somanuals.com. All Manuals Search And Download.
PLACING THE DISHWASHER
A. Mounting bracket
for mounting to under
countertop
Placing the Dishwasher
A
The profile strips on the sides of the
dishwasher allow the dishwasher to fit into
a cabinet opening with a width of 24” (610
mm) to 24-1/4” (616 mm). Before sliding
the dishwasher into the cabinet opening:
•
Straighten the hot water supply line and
the electrical cable (see Figure 11).
Level & Align (initial adjustments).
Guide the drain hose carefully (avoiding
kinks in hose) as the dishwasher is slid
into the cabinet opening.
B
•
•
•
•
Make final leveling adjustments (see
FINAL STEPS Section).
Mount the dishwasher to maintain
positioning and alignment. Determine
which type of mounting your
dishwasher needs:
B. Mounting bracket
bent for mounting to
side of cabinets
Figure 10
Top Mount is used for all types of
countertops that will not be damaged
by drilling.
IMPORTANT
If you wish to change the front panel of
the dishwasher this must be done before
sliding the dishwasher into place.
•
For a top mount, position the
brackets flat on each of the top
corners of the dishwasher as
shown in Figure 10A.
*Note: Additional accessory door pa-
nels can not be used with SHU 9900
models.
Side Mount is used when there is a
granite, marble or other hard natural
surface counter top that could be
damaged by drilling.
•
For a side mount, bend the
brackets, then position them as
shown in Figure 10B.
•
•
Drive Mounting Screws (see Figure 3)
through the holes in the brackets. See
Figure 10A or 10B.
Connect the drain hose, hot water
supply line and electrical connections
as described in the following sections.
Figure 11
8 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
DRAIN HOSE CONNECTION
Air Gap
THESE INSTALLATION
Drain Hose
in Sink with
Air Gap/ No
Disposer
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Rubber
Connector
Be sure to follow your national
and local codes at all times.
Trap
Drain Hose
• Before beginning, turn off the water
supply!
Figure 12
• The access hole for the drain hose should
be 1.25” (32 mm) diameter.
• Use the hose clamps and rubber
connection hose (Figure 3) to connect
the drain hose to the sink, disposer or
air gap (Figure 14).
Air Gap
Drain Hose
in Sink
with Air
Gap &
Rubber
Connector
Disposer
Openings for drain lines must be
installed in the marked areas as
shown in Figures 8 and 9 to avoid
interference with the dishwasher
frame or other components.
disposer
Trap
Figure 13
G, Fig 3
Drain Hose
Connected
to Sink
CAUTION
Failure to provide the proper drain
connection height, 20” (508mm)
above floor level with high loop or
air gap, will result in improper
draining of the dishwasher.
Improper draining may cause
damage to the dishwasher.
Figure 14
ENGLISH - 9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOT WATER CONNECTION
THESE INSTALLATION
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
Shut off valve
(not included)
Connecting the Hot Water
Supply Line
• If using a solder joint instead of a com-
pression fitting, be sure to make all
solder connections before connecting
the water line to the dishwasher.
• Make sure there are no sharp bends or
kinks in the water line which might
restrict water flow.
Figure 15
• When connecting threaded pipe use pipe
thread compound or Teflon tape to seal
the connection.
• Before connecting the copper hot water
supply line to the dishwasher, it should
be flushed with hot water to clear any
foreign material.
• Apply Teflon tape or other pipe sealant
to 90° elbow fitting and connect
directly to water inlet valve*.
CAUTION
DO NOT SOLDER WITHIN 6 INCHES
(152.4 MM) OF THE DISHWASHER’S
INLET VALVE.
TEMPERATURES REQUIRED FOR
SOLDERING WILL DAMAGE THE
VALVE!
• Turn on the water supply to check for
leaks after making connections.
* Water inlet valve located at the bottom
left front of the dishwasher.
Openings for water lines must be
installed in the marked areas as shown
in Figures
8
and
9
to avoid
interference with the dishwasher
frame or other components.
Figure 16
10 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL SUPPLY CONNECTION
THESE INSTALLATION
WARNING
INSTRUCTIONS ARE
INTENDEDFORUSEBY
QUALIFIEDINSTALLERS
ELECTRICALSHOCKHAZARD
• DISCONNECT ELECTRICAL POWER
AT THE CIRCUIT BREAKER BOX OR
FUSE BOX BEFORE INSTALLING THE
DISHWASHER.
• ELECTRICALLY GROUND DISH-
WASHER.
• USE COPPER CONDUCTORS ONLY.
FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH.
Connecting Electrical Supply
Be sure to follow all local and natio-
nal electrical codes and ordinances.
Wire nuts NEED to have metal inserts!
DO NOT twist wires together before
installing wire nuts.
• Install strain relief or conduit connector
into opening on J-box.
• Strip the insulated wires, being extremely
careful not to strip too much insulation.
• Insert and securely fasten into strain re-
lief, two-conductor supply cable with
ground.
• Twist wire connectors tightly onto the
wires, ensuring that no bare wiring is
exposed (from insulated wires).
• Press wires back into J-box
• Securely fasten the J-box cover or toe
panel (depending on model) with
screw(s) provided from accessories
package.
Correct Connection in Junction Box
Black to Black
White to White
Green or Bare
to Green or Bare
U.L. listed
Conduit
Connector
or Strain
Relief
Figure 17
*
Junction box located at the bottom
front of the dishwasher base.
Grounding Instructions
This appliance must be connected to a
grounded metal permanent wiring system;
or an equipment grounding conductor
must be run with the circuit conductors
and connected to the equipment grounding
terminal or lead on the dishwasher. The
dishwasher must be properly grounded
before operating. Make sure that the
dishwasher is connected to a suitable
ground in compliance with the NATIONAL
ELECTRICAL CODE, in the United States,
or the CANADIAN ELECTRIC CODE C22.1-
latest edition, in Canada as well as any pro-
vincial/state or municipal or local codes that
apply.
Incorrect Connection in Junction Box
Figure 18
ENGLISH - 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR PANEL INSTALLATION
Accessory Panel Installation SHU Models
If you have an SHU model (other than the SHU 9910, 9920 or 9940 models) and have
ordered an accessory panel kit it must be installed prior to sliding the dishwasher into
place. Dimensions of panel size that may be used is shown in Figure 19.
Panel Installation, SHV Models
If you have an SHV model, a fully integrated model, you will have additional mounting
hardware and a folded template sheet with installation instructions comprised of
pictograms.
Refer to the folded template sheet for information on how to mount the panel. Please
note that one side of the template shows how to mount a one piece panel and the other
side of the template shows how to mount a two piece panel. Be sure of what type
installation you want before proceeding with the installation.
Refer to Figure 20 and Table 3 for guidelines on custom door panel selections.
After deciding if the extension pieces will be used or not refer to the pictograms printed
on the template for proper method of mounting your custom door.
Panel Installation, SHI Models
If you have an SHI model, an integrated model, you will have additional mounting
hardware and a folded template sheet with installation instructions comprised of
pictograms. In North America the black, white and stainless steel models of the integrated
series (SHI series), have a control panel that is 5-5/16” (135 mm) tall. The black and
white models come with a standard extension piece, dimension “A” in Figure 21 and
Table 4, next page. The stainless steel model comes with two extension pieces, referred
to as the standard and long extension piece in Table 4: the standard piece is used for
drawer heights up to 6” (152mm); the long extension piece is used for drawer heights
greater than 6” (152mm) but 6-7/16” (164mm) or less. These stainless steel extension
pieces are not installed in the control panel. In the stainless steel models, the two
extension pieces are shipped loose and must be inserted as shown in pictogram 5 on the
template sheet.
The purpose of the extension piece is to allow the increase of the control panel height to
try to match the horizontal drawer line of the cabinets. If your drawers are taller than the
“C” dimension shown on Table 4, it is recommended that the extension either be slid in
as far as it will go, or removed and the door made to fit directly below the control panel.
12 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR PANEL INSTALLATION
1/4” max.
(6 mm)
25”
(636 mm)
SEEFOLDEDPANELINSTALLATION
TEMPLATESHEETFORSTEPBYSTEP
INSTRUCTIONSONHOWTOINSTALL
YOUR DISHWASHER PANEL(S).
23-1/16”
(586 mm)
Figure 19
IMPORTANT
Do NOT Drill Completely through
your custom door panel.
EXTENSION "A"
MAX.-MIN.
"C"
MAX.-MIN.
MODEL
"B"
STANDARD
LONG
---------
---------
---------
13/16 - 0
(21 - 0 mm)
5 5/16
6 1/8 - 5 5/16
SHI 4302
SHI 4306
SHI 6802
SHI 6805
SHI 6806
(135 mm) (156 - 135 mm)
13/16 - 0
(21 - 0 mm)
5 5/16
6 1/8 - 5 5/16
(135 mm) (156 - 135 mm)
13/16 - 0
5 5/16
6 1/8 - 5 5/16
(135 mm) (156 - 135 mm)
11/16 - 5/16" 1 1/8 - 11/16"
5 5/16
6 7/16 - 5 5/8
(18-8mm)
(29 - 18mm)
(135 mm) (164 - 143 mm)
13/16 - 0
21 - 0 mm)
5 5/16
6 1/8 - 5 5/16
---------
(135 mm) (156 - 135 mm)
Figure 20
Table 4
MODEL
SHV
D
F
E*
27 3/16" - 30 5/16" 23 3/16 - 23 3/8
(690 - 770 mm) (589 - 594 mm)
N/A
20 11/16 - 25
(526-635 mm)
27 3/16" - 30 5/16" 23 3/16 - 23 3/8
(690 - 770 mm) (589 - 594 mm)
SHI
Table 5
Figure 21
*Note: Do not exceed 30 5/16” (770mm)
for the overall front panel length.
ENGLISH - 13
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ADJUSTMENTS
Door Tension Adjustment
(only in SHI and SHV models)
After installation of the dishwasher, open
and close the door several times to make
sure that it does so with ease. If the door
closes too quickly or if the door falls open,
the spring tension needs to be adjusted.
Adjust screws
on right and
left sides
To Adjust the Spring Tension
Obtain Spring Tension Screws (2) out
of the SHI/SHV parts bag (see Figure
3).
•
•
Torx T 20
Insert the screws in the right and left
sides and adjust spring tension as shown
(see Figure 22).
Figure 22
Leveling the Dishwasher
Raising the Rear
The rear leveling leg is adjusted by turning
the center screw at the front of the
dishwasher.
Raising the Front
The front leveling legs are adjusted by
rotating the leveling legs on the front left
and right sides of the dishwasher.
• Use a screwdriver and tap the end lightly
with a hammer to turn the legs (see
Figure 23).
Figure 23
Note: If additional height is needed:
Shims may be added under the leveler feet.
14 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
BASE AND TOE PANEL
SHU 6800 Series Base and Toe Panel Installation Steps
SHU6800 BASE PARTS
Installation Parts
•
•
•
•
•
SHU 6800 Base Part
Base Part Screws
SHU6800 Base Part
Base Part
SHU 6800 Toe Panel
Screws (1lft &1rgt)
SHU Toe Panel Screws
SHU 6800 Installation Kit
(Refer to “Materials Supplied” section)
(attached)
Toe Panel
Junction Box Cover and Screw
Remember to carefully check, the “Materials
Supplied” section against the SHU6800
Installation Kit bag and contents.
Figure 24
Disassembly Steps
Pull Toe Panel off (Figure 25).
Remove Base Part by pulling it out
and downward.
•
•
Figure 25
After installation, water and electrical
lines are connected and the unit leveled,
assemble the base part (see below).
Assembly Steps
•
Place J-Box Cover on J-Box, insert
and tighten screw (Figure 26).
Drop screws inside holes in base part.
Slip Base Part under and up front
bottom panel of dishwasher. Tighten
Base Part Screws - LOW TORQUE,
USE HAND TOOL ONLY.
•
•
•
Slip Cotton Insulation Strip under
unit, between the bottom of Base
Part and the floor.
Figure 26
Junction Box Cover is required
for any installation application
ENGLISH - 15
Download from Www.Somanuals.com. All Manuals Search And Download.
TOE PANEL AND HANDLE
Regular Toe Panel
Installation (for models
other than SHU 6800)
• Obtain Toe Panel Screws from the
Dishwasher Installation Kit bag (see
Figure 3).
• Insert screws through the Toe Panel.
• With a Torx screwdriver, fasten screws
and toe panel into dishwasher base.
Figure 27
SHU 9910/9920/8800/8810 Handle Assembly
The SHU 9900 model has a handle that needs to be assembled onto the door panel.
Reference installation kit and instructions provided with the handle. Refer to Figures 29
and 30.
2.
1.
3
2
1
3
Figure 29
Figure 28
16 - ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL CHECKLIST
Final Checklist
Check Electrical Requirements.
Be sure you have correct electrical supply and recommended grounding method.
Turn on the hot water shut-off valve and electrical supply. Water temperature should
be 140°F (60°C).
Operate the dishwasher through one cycle and check for plumbing leaks.
If the dishwasher does not operate properly, refer to the SELF- HELP, CUSTOMER
SERVICE and WARRANTY sections in the Use and Care Manual.
Customer Service Information
If service becomes necessary, contact your dealer or installer or an authorized service center. Do
not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may
void the warranty. If problem persists, take the following steps (in the order listed below) until the
problem is corrected to your satisfaction.
1. Contact your installer or the Bosch Authorized Service Contractor in your area.
3. Write to us at the address below:
BSH Home Appliances, Corp.
5551 McFadden Avenue
Huntington Beach, CA 92649
4. Call us at: 1-800/944-2904.
Please be sure to include (if writing), or have available (if calling), the following information:
•
•
•
•
•
Model Number
Serial Number
Date of Original Purchase
Date Problem Originated
Explanation of Problem
Also, if writing, please be sure to include a daytime phone number.
(You will find the model number and serial number information on the label located on the right-hand
side of the inner door of the dishwasher).
LEAVEINSTALLATIONINSTRUCTIONSAND
USE & CARE MANUAL WITH OWNER.
ENGLISH - 17
Download from Www.Somanuals.com. All Manuals Search And Download.
56 02 04 2334 (8108)/ CS Part # 481829
Download from Www.Somanuals.com. All Manuals Search And Download.
|