Bolens Snow Blower C Style User Manual

Safety • Assembly • Operation • Maintenance • Troubleshooting • Parts Lists • Warranty

OPERATOR’S MANUAL

Two-Stage Snow Thrower — C, D Style

IMPORTANT

READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION

Warning: This unit is equipped with an internal combustion engine and should not be used on or near any uniiproved forest-covered, brush-

covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).

If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law

(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester

for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,

Ohio 44136-0019.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019

PRINTED IN U.S.A

FORM NO. 769-01274D

08/05/2005

Download from Www.Somanuals.com. All Manuals Search And Download.

��

�

��

Safety

Labels

��

�

��

�

��

�

��

�

��

WARNING

��

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this

manual before at-

��

tempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

��

HEED ITS WARNING!

A chute clean-out tool is fastened to the top of the

auger housing with a mounting clip. The tool is designed

to clear a chute assembly of ice and snow.

This item is fastened with a cable tie at the factory. Cut

the cable tie before operating the snow thrower.

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

��

WARNING: Never use your

hands to clear a clogged chute

assembly. Shut off engine and

remain behind handles until

all moving parts have stopped

before using the clean-out tool

to clear the chute assembly.

and on the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-

nents contain or emit chemicals known to State of California to cause cancer and

birth defects or other reproductive harm.

DANGER: This machine was built to be operated according to the rules for safe operation in this

manual. As with any type of power equipment, carelessness or error on the part of the operator can

result in serious injury. This machine is capable of amputating hands and feet and throwing objects.

Safe

Operation ^{Failure to observe the following safety instructions could result in serious injury or death.}

Training

Preparation

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

1. Thoroughly inspect the area where the equipment is to be

used. Remove all doormats, newspapers, sleds, boards,

wires and other foreign objects, which could be tripped over

or thrown by the auger/impeller.

Practices

2. Always wear safety glasses or eye shields during operation

and while performing an adjustment or repair to protect your

eyes. Thrown objects which ricochet can cause serious

injury to the eyes.

3. Do not operate without wearing adequate winter outer

garments. Do not wear jewelry, long scarves or other

loose clothing, which could become entangled in moving

parts. Wear footwear which will improve footing on slippery

surfaces.

4. Use a grounded three-wire extension cord and receptacle

for all units with electric start engines.

5. Adjust collector housing height to clear gravel or crushed

rock surfaces.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them quickly.

3. Never allow children under 14 years old to operate this

machine. Children 14 years old and over should read and

understand the operation instructions and safety rules in

this manual and should be trained and supervised by a

parent.

4. Never allow adults to operate this machine without proper

instruction.

5. Thrown objects can cause serious personal injury. Plan

your snow-throwing pattern to avoid discharge of material

toward roads, bystanders and the like.

6. Keep bystanders, helpers, pets and children at least 75 feet

from the machine while it is in operation. Stop machine if

anyone enters the area.

7. Exercise caution to avoid slipping or falling, especially

when operating in reverse.

WARNING

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this

6. Disengage all control levers before starting the engine.

7. Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

8. Let engine and machine adjust to outdoor temperature

before starting to clear snow.

9. To avoid personal injury or property damage use extreme

care in handling gasoline. Gasoline is extremely flammable

and the vapors are explosive. Serious personal injury can

occur when gasoline is spilled on yourself or your clothes,

which can ignite. Wash your skin and change clothes

immediately.

manual before at-

tempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

a. Use only an approved gasoline container.

b. Extinguish all cigarettes, cigars, pipes and other sources

of ignition.

c. Never fuel machine indoors.

d. Never remove gas cap or add fuel while the engine is hot

or running.

HEED ITS WARNING!

e. Allow engine to cool at least two minutes before refuel-

ing.

f. Never over fill fuel tank. Fill tank to no more than ½ inch

below bottom of filler neck to provide space for fuel

expansion.

g. Replace gasoline cap and tighten securely.

h. If gasoline is spilled, wipe it off the engine and equip-

ment. Move machine to another area. Wait 5 minutes

before starting the engine.

i. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light (e.g. furnace,

water heater, space heater, clothes dryer etc.).

j. Allow machine to cool at least 5 minutes before storing.

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Maintenance & Storage

1. Do not put hands or feet near rotating parts, in the

auger/impeller housing or chute assembly. Contact with the

rotating parts can amputate hands and feet.

1. Never tamper with safety devices. Check their proper

operation regularly. Refer to the maintenance and adjust-

ment sections of this manual.

2. The auger/impeller control lever is a safety device. Never

bypass its operation. Doing so makes the machine unsafe

and may cause personal injury.

3. The control levers must operate easily in both directions

and automatically return to the disengaged position when

released.

4. Never operate with a missing or damaged chute assembly.

Keep all safety devices in place and working.

5. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless and

deadly gas.

6. Do not operate machine while under the influence of alcohol

or drugs.

7. Muffler and engine become hot and can cause a burn. Do

not touch.

8. Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while operat-

ing on slopes.

10. Plan your snow-throwing pattern to avoid discharge towards

windows, walls, cars etc. Thus, avoiding possible property

damage or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets or

allow anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear

snow at too fast of a rate.

13. Never operate this machine without good visibility or light.

Always be sure of your footing and keep a firm hold on the

handles. Walk, never run.

14. Disengage power to the auger/impeller when transporting or

not in use.

15. Never operate machine at high transport speeds on slippery

surfaces. Look down and behind and use care when

backing up.

16. If the machine should start to vibrate abnormally, stop the

engine, disconnect the spark plug wire and ground it against

the engine. Inspect thoroughly for damage. Repair any

damage before starting and operating.

17. Disengage all control levers and stop engine before you

leave the operating position (behind the handles). Wait

until the auger/impeller comes to a complete stop before

unclogging the chute assembly, making any adjustments, or

inspections.

2. Before cleaning, repairing, or inspecting machine disen-

gage all control levers and stop the engine. Wait until the

auger/impeller come to a complete stop. Disconnect the

spark plug wire and ground against the engine to prevent

unintended starting.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

4. Do not change the engine governor setting or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid shoes are subject to

wear and damage. For your safety protection, frequently

check all components and replace with original equipment

manufacturer’s (OEM) parts only. “Use of parts which do

not meet the original equipment specifications may lead to

improper performance and compromise safety!”

6. Check controls periodically to verify they engage and

disengage properly and adjust, if necessary. Refer to the

adjustment section in this operator’s manual for instructions.

7. Maintain or replace safety and instruction labels, as neces-

sary.

Safe

Operation

Practices

WARNING

This symbol points

8. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

out important safety

instructions, which if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this man-

ual before attempting to

operate this machine.

Failure to comply with

these instructions may

result in personal injury.

When you see this

9. Prior to storing, run machine a few minutes to clear snow

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light such as a water

heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper instructions

on off-season storage.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way.Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice regarding Emissions

Engines which are certiﬁed to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certiﬁed to operate on regular unleaded gasoline, and may

include the following emission control systems: Engine Modiﬁca-

tion (EM) and Three Way Catalyst (TWC) if so equipped.

symbol.

HEED IT’S WARNING!

Your Responsibility

18. Never put your hand in the discharge or collector openings.

Always use the clean-out tool provided to unclog the dis-

charge opening. Do not unclog chute assembly while engine

is running. Shut off engine and remain behind handles until

all moving parts have stopped before unclogging.

19. Use only attachments and accessories approved by the

manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20. If situations occur which are not covered in this manual,

use care and good judgment. Contact your dealer or call

(800) 800-7310 for assistance and the name of your nearest

servicing dealer..

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

Restrict the use of this power machine to persons who read, un-

derstand and follow the warnings and instructions in this manual

and on the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting Up

Your Snow

Thrower

NOTE: References to right

or left side of the snow

thrower are determined

from behind the unit in the

operating position (standing

directly behind the snow

thrower, facing the handle

panel).

1. Observe the lower rear area of the snow thrower to

be sure both cables are aligned with roller guides

before pivoting the handle upward.

2. Secure the handle by tightening the plastic wing

knob located on both the left and right sides of the

handle. Remove and discard any rubber bands, if

present. They are for packaging purposes only.

3. Position the chute assembly over the base.

NOTE: Snow throwers vary

by model with regard to

features and components.

Your snow thrower may

NOT resemble, in detail,

snow throwers illustrated

in figures throughout this

manual.

4. Close the flange keepers to secure the chute

assembly to the chute base. The flange keepers will

click into place when properly secure.

NOTE: If the flange keepers will not easily click into

place, use the palm of your hand to apply swift, firm

pressure to the back of each.

NOTE: Two replacement

auger shear pins are

included with this manual

(or stowed in the plastic

handle panel). Refer to

Augers on page 16 for more

information regarding shear

pin replacement.

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Remove the flat washer and hairpin clip from the end

of the chute directional control.

Insert the end of the chute directional control into the

lower bracket and secure with the flat washer and hair-

pin clip just removed. If necessary, the lower bracket

can be adjusted. Refer to Chute Bracket Adjustment.

on Page 13.

Setting Up

Your Snow

Thrower

6. Insert the shift lever through the speed select panel

and secure to the shift spring lever with the two hex

head bolts and flange lock nuts that come attached to

the shift lever.

IMPORTANT: Prior to operating your snow thrower, refer

to Auger Control Test on page 11. Read and follow all

instructions carefully and perform all adjustments to verify

your snow thrower is operating safely and properly.

Tire Pressure

Before operating, check tire pressure and reduce pres-

sure in both tires to between 15 psi and 20 psi.

�

IMPORTANT

Prior to operating your

snow thrower, refer

to Auger Control Test

on page 11. Read and

follow all instructions

carefully and perform

all adjustments to verify

your snow thrower is

operating safely and

properly.

NOTE: If the tire pressure is not equal in both tires, the

unit may not travel in a straight path and the shave plate

may wear unevenly.

Download from Www.Somanuals.com. All Manuals Search And Download.

KnowYour Snow Thrower

��

Operating

Your Snow

Thrower

��

WARNING

��

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

��

Figure 1

Now that you have set up your snow thrower for

operation, get acquainted with its controls and fea-

tures. These are described below and illustrated in

Figure 1. This knowledge will allow you to use your

Choke Control

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

new equipment to its fullest potential.

NOTE: For detailed starting instructions and more

information on all engine controls, refer to the Tecumseh

Engines manual packed separately and Starting The

Engine on page 10 of this manual.

The choke control is found on the rear of the engine and

is activated by rotating the knob clockwise. Activating the

choke control closes the choke plate on the carburetor

and aids in starting the engine.

Throttle Control

Shift Lever

The throttle control is located on the

engine. It regulates the speed of the

engine and will shut off the engine when

pushed down completely.

The shift lever is located between the lower handles.

Place the shift lever into any of eight positions to control

the direction of travel and ground speed.

Primer

Depressing the primer forces fuel directly

into the engine’s carburetor to aid in

cold-weather starting.

NOTE: Snow throwers vary

by model with regard to

features and components.

Your snow thrower may

NOT resemble, in detail,

snow throwers illustrated

in figures throughout this

manual.

Forward

There are six forward (F) speeds. Position one (1) is the

slowest and position five (5) is the fastest.

Reverse

Oil Fill

Engine oil level can be checked and oil

added through the oil fill.

There are two reverse (R) speeds. One (1) is the slower

and two (2) is the faster.

��

Download from Www.Somanuals.com. All Manuals Search And Download.

Auger Control

Ignition Key

The ignition key is a safety devise. It must be fully

inserted in order for the engine to start. Remove the

ignition key when the snow thrower is not in use.

Do not turn the ignition key in an attempt to start the

engine. Doing so may cause it to break.

��

Clean-Out Tool

Operating

Your Snow

Thrower

WARNING: Never use your hands

to clear a clogged chute assem-

bly. Shut off engine and remain

behind handles until all moving

parts have stopped before

unclogging.

��

The auger control is located on the left handle. Squeeze

the control grip against the handle to engage the augers

and start snow throwing action. Release to stop.

The chute clean-out tool is fastened to the top of the

auger housing with a mounting clip. The tool is designed

to clear a clogged chute assembly.

Drive Control

��

NOTE: This item is fastened with a cable tie to the rear

of the auger housing at the factory. Cut the cable tie

before operating the snow thrower.

WARNING

Skid Shoes

The operation of

any snow thrower

can result in foreign

objects being thrown

into the eyes, which

can damage your

Position the skid shoes based on surface conditions.

Adjust upward for hard-packed snow. Adjust downward

when operating on gravel or crushed rock surfaces.

��

Recoil Starter Handle

This handle is used to manually start the engine.

The drive control is located on the right handle. Squeeze

the control grip against the handle to engage the wheel

drive. Release to stop.

eyes severely. Always

wear safety glasses

while operating the

snow thrower, or while

performing any adjust-

ments or repairs on it.

Electric Starter Button

Pressing the electric starter button engages the engine’s

electric starter when plugged into a 120V power source.

Chute Directional Control

Electric Starter Outlet

Requires the use of a three-prong outdoor extension cord

and a 120V power source/wall outlet.

��

Augers

Be sure no one other

than the operator is

standing near the snow

thrower while starting

engine or operating

snow thrower. Never

run engine indoors or

in enclosed, poorly

ventilated areas. En-

gine exhaust contains

carbon monoxide, an

odorless and deadly

gas. Keep hands, feet,

hair and loose clothing

away from any moving

parts on engine and

snow thrower.

When engaged, the augers rotate and draw snow into the

auger housing.

Chute Assembly

Snow drawn into the auger housing is discharged out the

chute assembly.

The chute directional control is located on left side of the

snow thrower.

To change the direction in which snow is thrown, turn

chute directional control as follows:

Gas Cap

Unthread the gas cap to add gasoline to the fuel tank.

• Crank clockwise to discharge to the left.

• Crank counterclockwise to discharge to the right.

Download from Www.Somanuals.com. All Manuals Search And Download.

6. As the engine warms, slowly rotate the choke control

to the OFF position. If the engine falters, quickly rotate

the choke control back to FULL and then slowly into

the OFF position again.

Gas & Oil Fill-Up

Service the engine with gasoline and oil as instructed in

the Tecumseh Engines manual packed separately with

your snow thrower. Read instructions carefully.

Starting The Engine

7. When disconnecting the extension cord, always

unplug the end at the three-prong wall outlet before

unplugging the opposite end from the snow thrower.

1. Attach spark plug wire to spark plug. Make certain the

metal loop on the end of the spark plug wire (inside

the rubber boot) is fastened securely over the metal

tip on the spark plug.

WARNING

Recoil Starter

1. Rotate choke control to FULL choke position (cold

2. Make certain both the auger control and drive control

are in the disengaged (released) position.

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

engine start).

3. Move throttle control up to FAST position. Insert

ignition key into slot. Make sure it snaps into place.

Do not attempt to turn the key.

NOTE: If the engine is already warm, place choke control

in the OFF position instead of FULL.

2. Push the primer two or three times for cold engine

start, making sure to cover vent hole in the center of

the primer when pushing.

NOTE: The engine cannot start unless the key is

inserted into ignition switch.

Use extreme care

when handling

NOTE: DO NOT use primer to restart a warm engine

after a short shutdown.

Electric Starter

1. Determine that your home’s wiring is a three-wire

grounded system. Ask a licensed electrician if you are

not certain.

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

NOTE: Additional priming may be necessary if the

temperature is below 15° Fahrenheit.

WARNING: The optional electric

starter is equipped with a

3. Grasp the recoil starter handle and slowly pull the

rope out. At the point where it becomes slightly harder

to pull the rope, slowly allow the rope to recoil.

grounded three-wire power cord

and plug, and is designed to op-

erate on 120 volt AC household

current. It must be used with a

properly grounded three-prong

receptacle at all times to avoid

the possibility of electric shock.

Follow all instructions carefully

prior to operating the electric

starter.

4. Pull the starter handle with a firm, rapid stroke. Do not

release the handle and allow it to snap back. Keep a

firm hold on the starter handle and allow it to slowly

recoil.

5. As the engine warms, slowly rotate the choke control

to the OFF position. If the engine falters, quickly rotate

the choke control back to the FULL position and then

slowly into the OFF position again.

If your home’s

NOTE: Allow the engine to warm up for a few minutes

after starting. The engine will not develop full power until

it reaches operating temperatures.

wiring system is not a

three-wire grounded

system, do not use

this electric starter

under any conditions.

If you have a grounded three-prong receptacle, proceed

as follows:

1. Plug the extension cord into the outlet located on the

engine’s surface. Plug the other end of extension cord

into a three-prong 120-volt, grounded, AC outlet in a

well-ventilated area.

Stopping The Engine

Run engine for a few minutes before stopping to help dry

off any moisture on the engine.

• To help prevent possible starter freeze-up, proceed as

follows:

2. Rotate choke control to FULL choke position (for a

cold engine start).

If your home

electrical system

is grounded, but a

three-hole receptacle

is not available, do

not use your snow

thrower’s electric

starter.

NOTE: If the engine is already warm, place choke control

in the OFF position instead of FULL.

Electric Starter

1. Connect extension cord to the electric starter outlet

on the engine, then to 120 volt AC outlet.

3. Push the primer two or three times for cold engine

start, making sure to cover vent hole in the center of

the primer when pushing.

2. With the engine running, push the starter button and

allow the starter for spin for several seconds. The

noise made by the starter is normal. The engine’s

starter is not being harmed.

NOTE: DO NOT use primer to restart a warm engine

after a short shutdown.

3. When disconnecting the extension cord, always

unplug the end at the three-prong wall outlet before

unplugging the opposite end from the snow thrower.

4. Push starter button to start engine.

5. Once the engine starts, release starter button.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Move throttle control to STOP position.

To Engage Augers

5. Remove the ignition key and store in a safe place.

1. To engage the augers and start throwing snow,

squeeze the auger control against the left handle.

Release to stop the augers.

6. Wipe all snow and moisture from the area around the

engine as well as the area in and around the drive

control and auger control. Also, engage and release

both controls several times.

When selecting a

Drive Speed, use the

slower speeds until

you are comfortable

and familiar with the

operation of the snow

thrower.

Auger Control Test

Perform the following test before operating your snow

thrower for the first time and at the start of each winter.

Check the adjustment of the auger control as follows:

1. When the auger control is released and in the

disengaged “up” position, the cable should have very

little slack. It should NOT be tight.

Recoil Starter

1. With engine running, pull starter rope with a rapid,

continuous full arm stroke three or four times. Pulling

the starter rope will produce a loud clattering sound,

which is not harmful to engine.

2. In a well-ventilated area, start the snow thrower engine

as instructed on the previous page. Make sure the

throttle is set in the FAST position.

2. Move throttle control to STOP position.

3. Remove the ignition key and store in a safe place.

NEVER reposition the

shift lever (change

speeds or direction

of travel) without first

releasing the drive

control and bringing

the snow thrower

to a complete stop.

Doing so will result in

premature wear to the

snow thrower’s drive

system.

4. Wipe all snow and moisture from the area around the

engine as well as the area in and around the drive

control and auger control. Also, engage and release

both controls several times.

3. While standing in the operator’s position (behind the

snow thrower), engage the auger.

4. Allow the auger to remain engaged for approximately

ten (10) seconds before releasing the auger control.

Repeat this several times.

Chute Clean-Out Tool

5. With the throttle control in the FAST (rabbit) position

and the auger control in the disengaged “up” position,

walk to the front of the machine.

The chute clean-out tool is conveniently fastened to the

rear of the auger housing with a mounting clip. Should

snow and ice become lodged in the chute assembly

during operation, proceed as follows to safely clean the

chute assembly and chute opening:

6. Confirm that the auger has completely stopped

rotating and shows NO signs of motion. If the auger

shows ANY signs of rotating, immediately return to the

operator’s position and shut off the engine. Wait for

ALL moving parts to stop before re-adjusting the auger

control.

1. Release both the Auger Control and the Drive Control.

2. Stop the engine by removing the ignition key.

3. Remove the clean-out tool from the clip which secures

it to the rear of the auger housing.

7. To readjust the control cable, loosen the upper hex nut

on the auger cable bracket.

4. Use the shovel-shaped end of the clean-out tool to

dislodge and scoop any snow and ice which has

formed in and near the chute assembly.

8. Position the bracket upward to provide more slack (or

downward to increase cable tension). See Figure 2.

5. Refasten the clean-out tool to the mounting clip on the

rear of the auger housing, reinsert the ignition key and

start the snow thrower’s engine.

9. Retighten the upper hex nut.

10.Repeat Auger Control Test to verify proper adjust-

ment has been achieved.

6. While standing in the operator’s position (behind the

snow thrower), engage the auger control for a few

seconds to clear any remaining snow and ice from the

chute assembly.

WARNING

Never use your hands

to clean snow and

ice from the chute

assembly or auger

housing.

To Engage Drive

1. With the throttle control in the Fast (rabbit) position,

move shift lever into one of the six forward (F)

positions or two reverse (R) positions. Select a speed

appropriate for the snow conditions and a pace you’re

comfortable with.

The muffler, engine

and surrounding

areas become hot

and can cause a

burn. Do not touch.

2. Squeeze the auger control against the handle and the

augers will turn. Release it and the augers will stop.

3. Squeeze the drive control against the handle the snow

thrower will move. Release it and drive motion will

stop.

Figure 2

Download from Www.Somanuals.com. All Manuals Search And Download.

Auger Control

Refer to Auger Control Test on Page 11 to adjust the

auger control.

Drive Control

When the drive control is released and in the disen-

gaged “up” position, the cable should have very little

slack. It should NOT be tight.

Making

Adjustments

Check the adjustment of the drive control as follows:

1. With the drive control released, push the snow

thrower gently forward. The unit should roll freely.

2. Engage the drive control and gently attempt to push

the snow thrower forward. The wheels should not

turn. The unit should not roll freely.

3. With the drive control released, move the shift lever

back and forth between the R2 position and the F6

position several times. There should be no resistance

in the shift lever.

Figure 3

4. If any of the above tests failed, the drive cable is in

need of adjustment. Proceed as follows:

5. Loosen the lower hex nut on the drive cable bracket.

See Figure 3.

WARNING

6. Position the bracket upward to provide more slack (or

downward to increase cable tension).

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

7. Retighten the upper hex nut.

Chute Assembly

The distance snow is thrown can be adjusted by chang-

ing the angle of the chute assembly. To do so:

1. Stop the engine by removing the ignition key and

loosen the plastic wing knob found on the left side of

the chute assembly.

Never attempt to

make any adjust-

ments while the

engine is running,

except where speci-

fied in operator’s

manual.

2. Pivot the chute upward or downward before retight-

ening the wing knob. See Figure 4.

Figure 4

Download from Www.Somanuals.com. All Manuals Search And Download.

Skid Shoes

The space between the skid shoes and the ground can

be adjusted. See Figure 5.

• For close snow removal on a smooth surface, raise

skid shoes higher on the auger housing.

• Use a middle or lower position when the area to be

cleared is uneven, such as a gravel driveway.

Making

Adjustments

To adjust the skid shoes:

1. Loosen the four hex nuts (two on each side) and

carriage bolts. Move skid shoes to desired position.

2. Make certain the entire bottom surface of skid shoe is

against the ground to avoid uneven wear on the skid

shoes.

3. Retighten nuts and bolts securely.

Figure 5

Chute Bracket Adjustment

If the spiral at the bottom of the chute directional control

is not fully engaging with the chute assembly, the chute

bracket can be adjusted. To do so:

1. loosen the two nuts which secure the chute bracket

and reposition it slightly. See Figure 6.

WARNING

2. Retightening the nuts.

Loose gravel can be picked

up and thrown by the auger,

causing injury to the operator

and bystanders and/or

damage to the snow thrower

and surrounding property.

Tire Pressure

Before operating, check tire pressure and reduce pres-

sure to between 15 psi and 20 psi.

If the tire pressure is not equal in both tires, the unit may

pull to one side or the other.

Figure 6

Download from Www.Somanuals.com. All Manuals Search And Download.

Engine

Refer to the separate Tecumseh Engines manual

packed with your unit for all engine maintenance.

Lubrication

Engine

Refer to the separate Tecumseh Engines manual

packed with your unit for all engine lubrication instruc-

tions.

Maintaining

Your Snow

Thrower

Gear Shaft

The gear (hex) shaft should be lubricated at least once

a season or after every 25 hours of operation.

1. Remove the lower frame cover by removing the two

screws which secure it.

2. Apply a light coating of an all-weather multi-purpose

grease to the hex shaft. See Figure 7.

Figure 7

Wheels

At least once a season, remove both wheels. Clean and

coat the axles with a multipurpose automotive grease

before reinstalling wheels.

��

WARNING

Chute Directional Control

Once a season, the joystick should be lubricated with

petroleum jelly, linseed oil, mineral oil, paraffin wax or

3-in-1 oil.

Before lubricating,

repairing, or inspect-

ing, disengage all

controls and stop

engine. Wait until all

moving parts have

come to a complete

stop.

Auger Shaft

At least once a season, remove the shear pins on auger

shaft. Spray lubricant inside shaft, around the spacers.

Also lubricate the flange bearings found at either end of

the shaft. See Figure 8.

Gear Case

The auger gear case has been filled with grease at the

factory. If disassembled for any reason, lubricate with

two ounces of grease (Part Number 737-0168).

Figure 8

NOTE: Do not overfill the gear case. Damage to the

seals could result. Be sure the vent plug is free of

grease in order to relieve pressure.

Avoid oil spillage on

rubber friction wheel

and aluminum drive

plate.

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the

snow thrower are subject to wear. They should be

checked periodically and replaced when necessary.

To remove skid shoes:

Do not overfill the gear

case. Damage to the

seals could result.

1. Remove the four carriage bolts and hex flange nuts

which secure them to the snow thrower.

2. Reassemble new skid shoes with the four carriage

bolts (two on each side) and hex flange nuts. Refer

to Figure 9.

��

To remove shave plate:

1. Remove the carriage bolts and hex nuts which

attach it to the snow thrower housing.

Figure 9

2. Reassemble new shave plate, making sure heads of

carriage bolts are to the inside of housing. Tighten

securely.

Download from Www.Somanuals.com. All Manuals Search And Download.

Auger Belt Replacement

To remove and replace your snow thrower’s auger belt,

proceed as follows:

1. Remove the plastic belt cover on the front of the

engine by removing the two self-tapping screws.

NOTE: Drain the gasoline from the snow thrower, or

place a piece of plastic under the gas cap.

Maintaining

Your Snow

Thrower

2. Carefully pivot the snow thrower up and forward so

that it rests on the auger housing. Remove the frame

cover from the underside of the snow thrower by

removing four self-tapping screws which secure it.

3. Roll the auger belt off the engine pulley.

4. a. Loosen and remove the shoulder screw which

acts as a belt keeper.

b. Unhook the support bracket spring from the

frame.

5. Remove the belt from around the auger pulley, and

slip the belt between the support bracket and the

auger pulley. Reassemble auger belt by following

instructions in reverse order.

NOTE: Although

multi-viscosity oils

(5W30, 10W30 etc.)

improve starting in cold

weather, these multi-

viscosity oils also result

in higher oil consump-

tion when used above

32ºF. Check your snow

thrower’s engine oil

level more frequently to

avoid possible engine

damage from running

low on oil.

NOTE: Do NOT forget to reinstall the shoulder screw

and reconnect the spring to the frame after installing a

replacement auger belt.

NOTE: Do not sand-

blast spark plug. Spark

plug should be cleaned

by scraping or wire

brushing and washing

with a commercial

solvent.

IMPORTANT

NEVER replace the

auger shear pins with

standard pins. Any

damage to the auger

gearbox or other com-

ponents, as a result of

doing so, will NOT be

covered by your snow

thrower’s warranty.

�

Download from Www.Somanuals.com. All Manuals Search And Download.

Augers

• The augers are secured to the spiral shaft with two

shear pins and cotter pins. If the auger should strike a

foreign object or ice jam, the snow thrower is designed

so that the pins may shear. Refer to Figure 9.

• If the augers will not turn, check to see if the pins have

sheared. One set of replacement shear pins has been

provided with the snow thrower. When replacing pins,

spray an oil lubricant into shaft before inserting new

pins.

Maintaining

Your Snow

Thrower

Drive Belt Replacement

To remove and replace your snow thrower’s auger belt,

proceed as follows:

1. Remove the plastic belt cover on the front of the

engine by removing the two self-tapping screws.

• Drain the gasoline from the snow thrower, or place a

piece of plastic under the gas cap.

• Carefully pivot the snow thrower up and forward so

that it rests on the auger housing.

NEVER replace

the auger shear

pins with anything

other than OEM

2. Remove the frame cover from the underside of the

snow thrower by removing four self-tapping screws

which secure it.

3. a. Grasp the idler pulley and pivot it toward the right.

b. Roll the auger belt off the engine pulley.

c. Lift the drive belt off engine pulley.

4. Slip the drive belt off the pulley and between friction

wheel and friction wheel disc.

Part No.738-04124

replacement shear

pins. Any damage to

the auger gearbox

or other components

as a result of failing

to do so will NOT be

covered by your snow

thrower’s warranty.

• Remove and replace belt in the reverse order.

�

Download from Www.Somanuals.com. All Manuals Search And Download.

Friction Wheel Removal

If the snow thrower fails to drive with the drive control

engaged, and performing the drive control cable adjust-

ment on page 14 fails to correct the problem, the friction

wheel may need to be replaced. Follow the instructions

below. Examine the friction wheel for signs of wear or

cracking and replace if necessary

• Place the shift lever in third Forward (F3) position.

Maintaining

Your Snow

Thrower

• Drain the gasoline from the snow thrower, or place a

piece of plastic under the gas cap.

• Carefully pivot the snow thrower up and forward so

that it rests on the auger housing.

1. a. Remove the frame cover from the underside of

the snow thrower by removing four self-tapping

screws which secure it.

b. Remove the right-hand wheel by removing the

screw and bell washer which secure it to the axle.

2. Carefully remove the hex nut and washer which

secures the hex shaft to the snow thrower frame and

lightly tap the shaft’s end to dislodge the ball bearing

from the right side of the frame.

When reassembling

the friction wheel as-

sembly, tighten each

screw only one rota-

tion before turning the

wheel clockwise and

proceeding with the

next screw. Repeat

this process several

times to ensure the

plates are secured

with equal force.

3. Carefully position the hex shaft downward and to

the left before carefully sliding the friction wheel

assembly off the shaft.

NOTE: If you’re replacing the friction wheel assembly

as a whole, discard the worn part and slide the new part

onto the hex shaft. Follow the steps above in reverse

order to reassemble components. If you’re disassem-

bling the friction wheel and replacing only the rubber

ring, proceed as follows:

4. Remove the four screws which secure the friction

wheel’s side plates together.

• Remove the rubber ring from between the plates.

• Reassemble the side plates with a new rubber ring.

• Slide the friction wheel assembly back onto the hex

shaft and follow the steps above in reverse order to

reassemble components.

NEVER replace

the auger shear

pins with anything

other than OEM

Part No.738-04124

replacement shear

pins. Any damage to

the auger gearbox

or other components

as a result of failing

to do so will NOT be

covered by your snow

thrower’s warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

If the snow thrower will not be used for 30 days or longer, 1. Remove all gasoline from the carburetor and the fuel

or if it is the end of the snow season when the last pos-

sibility of snow is gone, the equipment needs to be stored

properly. Follow storage instructions below to ensure top

performance from the snow thrower for many more years.

tank to prevent gum deposits from forming on these

parts and harming the engine.

2. Run the engine until the fuel tank is empty and it stops

due to lack of fuel.

Preparing Engine

3. Drain carburetor by pressing upward on bowl drain,

located below the carburetor cover (refer to the

Tecumseh engine manual for more detailed instruc-

tion).

Off-Season

Storage

WARNING: Never store snow

thrower with fuel in tank indoors

or in poorly ventilated areas,

where fuel fumes may reach an

open flame, spark or pilot light

as on a furnace, water heater,

clothes dryer or gas appliance.

WARNING: Do not drain carbure-

tor if using fuel stabilizer. Never

use engine or carburetor cleaning

products in the fuel tank or

permanent damage may occur.

NOTE: It is important to prevent gum deposits from form-

ing in essential fuel system parts of the engine such as

the carburetor, fuel filter, fuel hose or tank during storage.

NOTE: Fuel stabilizer (such as STA-BIL) is an accept-

able alternative in minimizing the formation of fuel gum

deposits during storage. Add stabilizer to gasoline in fuel

tank or storage container. Always follow mix ratio found on

stabilizer container. Run engine at least 10 minutes after

adding stabilizer to allow it to reach the carburetor. Do not

drain carburetor if using fuel stabilizer.

WARNING

Never store snow

thrower with fuel

in tank indoors or

in poorly ventilated

areas, where fuel

fumes may reach an

open flame, spark

or pilot light as on a

furnace, water heater,

clothes dryer or gas

appliance.

CAUTION: Alcohol blended fuels (called gasohol or using

ethanol or methanol) can attract moisture which leads to

separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in

storage.

4. Remove the spark plug and pour one (1) ounce of

engine oil through the spark plug hole into the cylinder.

Cover spark plug hole with a rag and crank the engine

several times to distribute the oil. Replace spark plug.

To avoid engine problems, the fuel system should be

emptied before storage for 30 days or longer. Follow

these instructions to prepare your snow thrower for

storage:

NOTE: Refer to the Tecumseh engine manual for more

information on preparing the snow thrower engine for

storage.

WARNING: Drain fuel into an ap-

proved container outdoors, away

from any open flame. Be certain

engine is cool. Do not smoke.

Fuel left in engine during warm

weather deteriorates and will

cause serious starting problems.

Preparing Snow Thrower

Drain fuel into an

approved container

outdoors, away from

any open flame. Be

certain engine is

1. When storing the snow thrower in an unventilated or

metal storage shed, care should be taken to rustproof

the equipment. Using a light oil or silicone, coat the

equipment, especially any chains, springs, bearings

and cables.

cool. Do not smoke.

Fuel left in engine

during warm weather

deteriorates and will

cause serious

2. Remove all dirt from exterior of engine and equipment.

3. Follow lubrication recommendations on page 12.

4. Store equipment in a clean, dry area.

starting problems.

Do not drain

carburetor if

using fuel stabilizer.

Never use engine or

carburetor cleaning

products in the fuel

tank or permanent

damage may occur.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem

Engine fails to start

Cause

1. Choke not in ON position.

2. Spark plug wire disconnected.

3. Fuel tank empty or stale fuel.

4. Engine not primed.

Remedy

1. Move choke to ON position.

2. Connect wire to spark plug.

3. Fill tank with clean, fresh gasoline.

4. Prime engine as instructed in

“Operating Your Snow Thrower”.

Trouble-

Shooting

5. Clean, adjust gap, or replace.

6. Clean fuel line.

5. Faulty spark plug.

6. Blocked fuel line.

7. Insert key fully into the switch.

7. Safety key not in ignition on engine.

1. Unit running on CHOKE.

1. Move choke lever to OFF position.

Engine runs erratic

Engine overheats

2. Clean fuel line; fill tank with clean,

fresh gasoline.

2. Blocked fuel line or stale fuel.

3. Water or dirt in fuel system.

4. Carburetor out of adjustment.

NOTE: This section

addresses minor

3. Drain fuel tank. Refill with

fresh fuel.

service issues. For

further details, contact

a MTD authorized

service center or call

1 (800) 800-7310 for

assistance.

4. Contact MTD Service Center.

1. Carburetor not adjusted properly.

1. Loose parts or damaged auger.

1. Contact MTD Service Center.

1. Stop engine immediately and

disconnect spark plug wire. Tighten

all bolts and nuts. If vibration

continues, have unit serviced by a

MTD Service Center.

Excessive

Vibration

Loss of power

1. Spark plug wire loose.

2. Gas cap vent hole plugged.

3. Exhaust port plugged.

1. Connect and tighten spark plug

wire.

2. Remove ice and snow from gas

cap. Be certain vent hole is clear.

3. Contact MTD Service Center.

1. Drive control cable in need of adjust-

ment.

1. Adjust drive control cable. Refer to

“Making Adjustments”.

Unit fails

to propel itself

2. Drive belt loose or damaged.

2. Replace drive belt.

1. Chute assembly clogged.

1. Stop engine immediately and

disconnect spark plug wire. Clean

chute assembly and inside of auger

housing with clean-out tool or a

stick.

Unit fails

to discharge snow

2. Foreign object lodged in auger.

2. Stop engine immediately and

disconnect spark plug wire.

Remove object from auger with

clean-out tool or a stick.

3. Auger control cable in need of adjust-

ment.

3. Refer to “Auger Control Test” on

page 11.

4. Auger belt loose or damaged.

5. Shear pin(s) sheared.

4. Refer to Maintenance section.

5. Replace with new shear pin(s).

Download from Www.Somanuals.com. All Manuals Search And Download.

Styles C & D

�

��

�

��

�

��

�

��

�

��

�

��

�

��

Download from Www.Somanuals.com. All Manuals Search And Download.

1. 731-2635

Snow Removal Tool Mount

29. 684-04107 Spiral Assembly, LH

30. 684-04108 Spiral Assembly, RH

31. 731-04870* Spacer, 1.25 OD x .75 ID x 1.00

2. 684-04057 Impeller Assembly, 12” Dia.

3. 710-0347

4. 710-0451

Hex Screw, 3/8-16, 1.75, Gr5

Bolt, Carriage, 5/16-18, .750 Gr1

32. 736-0188

Washer, Flat, .76 x 1.49 x .06

5. 710-0604A Screw, 5/16-18, 0.625

33. 741-0493A Bushing, Flange, .80 ID x .91 OD

34. 790-00087A Housing, 1” Hex Bearing

35. 790-00117 Shave Plate, 2.25 x 21.66

790-00120 Shave Plate, 2.25 x 23.66

790-00121 Shave Plate, 2.25 x 25.66

790-00118 Shave Plate, 2.25 x 27.66

6. 710-0703

Screw, Carriage, 1/4-20, .750, Gr5

Illustrated

Parts List

7. 712-04063 Nut, Flange Lock, 5/16-18, Nylon

8. 712-04064 Nut, Flange Lock, 1/4-20, Nylon

9. 712-04065 Nut, Flange Lock, 3/8-16, Nylon

10. 714-04040 Cotter Pin, Bow-tie

11. 725-0157

Cable, Tie, 3/16 x .05 x 7.4

36. 784-5580

37. 719-0319

38. 719-0320

39. 721-0179

40. 741-0662

41. 710-0642

Slide Shoe

12. 726-04012 Nut, Push-on, .25 Dia

13. 731-04705 Chute, Adapter 5” Dia

Housing, Auger, RH Reduced

Housing, Auger, LH Reduced

Seal, Oil, .750 ID

14. 732-0611

15. 736-0174

16. 736-0242

17. 736-0463

18. 731-2643

19. 738-0143

20. 738-0281

Spring, Extension, .38 OD x 3.6

Washer, Wave, .625 x .885 x .015

Washer, Bell, .340 x .872 x .060

Washer, Flat, .25 x .630 x .0515

Snow Removal Tool

Bearing, Flange, .75 x 1.0 x .59

Screw, Self-tapping, 1/4-20, 0.750

42. 711-04286 Axle, Auger, 22”

711-04285 Axle, Auger, 24”

711-04284 Axle, Auger, 26”

711-04283 Axle, Auger, 28”

To order replacement

parts, contact

Screw, Shoulder, .498 x .34, 3/8-16

Screw, Shoulder, .625 x .17, 3/8-16

1-800-800-7310,

or visit

21. 738-04124A Shear Pin, .25 x 1.50

43. 714-0161

Key, Hi-pro 3/16 x 5/8

www.mtdproducts.com.

22. 741-0245

23. 741-0309

Bearing, Hex Flange x .75 ID

Bearing, Ball, .75 ID x 1.85 OD

44. 715-04021 Pin, Dowel, .25 OD x 1.2

45. 717-04126

Shaft, Worm .75 OD

24. 756-0981A Flat Pulley, Idler, 2.75 OD

25. 790-00075 Housing, Bearing, 1.85 ID

26. 790-00080 Bracket, Auger Idler w/ Brake

27. 618-04170 Gearbox Assembly, Auger, 22”

46. 717-0528A Gear, Worm 20T

47. 718-04071 Collar, Thrust

48. 721-0325

49. 721-0327

50. 736-0351

51. 736-3084

52. 741-0663

Plug, 1/4 x .437

Seal, Oil, .75 x 1 x .131

Washer, Flat, .760 ID x 1.5 OD

Washer, Flat, .51 x 1.12

Bearing, Flange, .75 x 1.0 x .925

618-04171

Gearbox Assembly, Auger, 24”

618-04172 Gearbox Assembly, Auger, 26”

618-04173 Gearbox Assembly, Auger, 28”

28. 684-04068 Housing Assembly, Auger 22”

684-04069 Housing Assembly, Auger 24”

684-04070 Housing Assembly, Auger 26”

684-04071 Housing Assembly, Auger 28”

53. 741-0661A Bearing, Flange, .75 x 1.00 x .975

54. 746-04230 Clutch Cable, Auger, 47.23”

55. 629-0071

Extention Cord, 110V

* None found between spirals on models with 22-inch auger housing.

* One found between spirals on models with 24-inch auger housing.

* Two found between spirals on models with 26-inch auger housing.

* Three found between spirals on models with 28-inch auger housing.

NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured

on the previous page are standard equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Styles C & D

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

1. 631-04133 Handle Ass’y, Lock LH

24. 720-0201A Crank Knob, 1.0 Dia. x 3.2, Black

2. 631-04134A Handle Ass’y, Lock, RH

3. 684-04106A Handle Ass’y, Engagement LH

4. 684-04105A Handle Ass’y, Engagement, RH

25. 720-0284

26. 726-0100

27. 735-0234

28. 736-0185

29. 736-0451

Knob Assembly, Wing Nut, 5/16-18

Cap, Push, 3/8 Rod

Grommet, .44 ID x .94 OD x .50

Washer, Flat, .375 x .738 x .063

Washer, Saddle, 320 x .93 x .060

5. 710-0376

Screw, Self-tapping, 5/16-18, .625

6. 710-0604A Screw, Self-tapping, 5/16-18, 1.0

Illustrated

Parts List

7. 710-0606

8. 710-1233

Screw, Self-tapping, 1/4-20, 1.50

Screw, Machine, #10-24, 1.375

30. 747-04263 Eye Bolt, Chute Crank

31. 749-04138 Handle, Lower

9. 712-04063 Nut, Flange Lock, 5/16-18, Nylon

10. 712-04064 Nut, Flange Lock, 1/4-20, Nylon

32. 749-04141

Handle, Upper, RH

33. 749-04142 Handle, Upper, LH

11. 720-0223

12. 720-0274

Grip, 0.5 ID x 3.45

Grip, 1.0 ID x 5.0

34. 731-04912A Chute, Lower, 5.0 Diameter

35. 710-0276

36. 710-04071 Bolt, Carriage, 5/16-18, 1.0

37. 710-0451 Bolt, Carriage, 5/16-18, .750

38. 731-04426A Chute, Upper, w/ Label

Bolt, Carriage, 5/16-18, 1.0

13. 732-04205 Spring Lever, Shift

14. 735-0199A Bumper, Rubber, .62 OD x .22

15. 736-0509

Washer, Flat, .350 sq. x .72 x .134

16. 738-04122 Screw, Shoulder, 1/4-20, .437

17. 747-04243 Lever, Shift

39. 736-0159

40. 741-0475

41. 784-5647

Washer.349 ID x .879 OD x .063

Bushing, Plastic, .380

Bracket, Chute Crank

18. 790-00100 Panel, Handle, (no cutout) C-Style

790-00101 Panel, Handle, (w/ cutout) D-Style

19. 790-00187 Panel, Speed Select (5 FW, 2 RV)

20. 684-04104 Crank Assembly, Chute

To order replacement

parts, contact

1-800-800-7310,

or visit

www.mtdproducts.com.

42. 731-04869 Chute, Flange Keeper

43. 747-1136

44. 725-1658

45. 725-1672

Retainer, Lens

Lamp, Halogen, 12V, 27W

Lens Assembly, Lamp

21. 710-0449

22. 710-1260A Screw, 5/16-18, 0.75, Gr5

23. 714-0104 Pin, Cotter, .072 x 1.13

Screw, Carriage, 5/16-18, 2.25

46. 725-04220 Wire Harness, Lamp

NOTE: A lamp cannot be added to a unit that did come come factory-equipped with a lamp.

NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured

on the previous page are standard equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Styles C & D

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

��

�

Download from Www.Somanuals.com. All Manuals Search And Download.

1. 756-04177 Disc, Friction Wheel

34. 790-00207 Guide Bracket, Drive Cable

35. 790-00226 Cover, Frame

2. 684-04153 Friction Wheel Assembly, 5.5 OD

3. 684-04154 Support Bracket, Friction Wheel

4. 684-04156 Shift Assembly, Rod

36. See Chart

Wheel Assembly

37. 731-04873 Spacer, 1.25 x .75 x 3.0

731-04877* Spacer, 1.25 x .75 x 1.50

38. 738-04168 Axle, .75 x 22”

5. 710-0627

6. 710-0788

7. 710-1652

Hex Screw, 5/16-24, .750, Gr5

Screw, 1/4-20, 1.000

Illustrated

Parts List

Screw 1/4-20x.625

39. 741-0919

40. 710-0106

41. 710-0191

Ball Bearing

8. 712-04065 Nut, Flange Lock, 3/8-16, Nylon

Hex Screw, 1/4-20, 1.25, Gr5

Hex Screw, 3/8-24, 1.25, Gr8

9. 712-0413

10. 714-0126

11. 716-0104

12. 716-0136

13. 716-0231

Nut, Jam Lock, 5/8-18, Gr5, Nylon

Key, Hi Pro, 3/16 x 3/4 Dia.

E-ring, .500 Dia.

42. 710-04520 Hex Screw, 5/16-24, 1.25, Gr5

43. 710-0654A Screw, Sems, 3/8-16, 1.00

44. 710-1245B Hex Screw, 5/16-24, .875, Gr8

45. 712-04064 Nut, Flange Lock, 1/4-20, Nylon

46. 726-04012 Nut, Push-on, .25 Dia.

47. 731-04792A Cover, Belt

E-ring, Retaining, .875 Dia.

E-ring, .750 Dia.

14. 717-04209 Hex Shaft, .8125, 7-Tooth

15. 717-04230 Gear, 80-Tooth

16. 726-0221

17. 732-0264

18. 736-0242

19. 736-0287

Speed Nut, .500

48. 732-04308 Spring, Torsion, .850 ID x .354

Extension Spring

49. 736-0247

50. 736-0362

51. 736-0505

Washer, Flat, .406 x 1.25 x .157

Washer, Flat, .330 x 1.25 x .06

Washer, Flat, .34 x 1.50 x .150

Washer, Bell, .340 x .872 x .060

Washer, Flat, .793 x 1.24 x .060

To order replacement

parts, contact

20. 736-04161 Washer, Flat, .75 x 1.00 x .060

21. 738-04164 Pin, Friction Disc

52. 748-04053 Pulley, Adapter, .75 Dia.

53. 748-04097 Spacer, Shoulder

1-800-800-7310,

or visit

www.mtdproducts.com.

22. 741-04098 Ball Bearing, 30 x 55 x 13

23. 738-04184 Screw, Shoulder, .373 x .10, 1/4-20

54. 750-04303 Spacer, .875 ID x 1.185 OD

55. 750-04477 Spacer, .340 x .750 x .360

56. 754-04050 Belt, Auger Drive

24. 738-0924

25. 741-0245

26. 741-0563

Screw, 1/4-28, .375

Bearing, Hex Flange x .75 ID

Bearing, Ball, 17 x 40 x 12

57. 754-04088 Belt, Wheel Drive

58. 756-04109 Pulley, Auger Drive, 8.1 x .5

59. 756-04113 Pulley, Half, V x 2.600 OD

60. 756-04179 Pulley, Half, 1/4-V x 1.5 OD

61. 790-00208 Idler Bracket, Wheel Drive

62. 790-00230 Sleeve, Bearing Idler

63. 750-04571 Spacer, Shoulder, .26 x .79 x .538

64. 735-04054 Rubber, Friction Wheel, 5.5 OD

27. 746-04229 Clutch Cable, Wheel, 44.95”

28. 746-04230 Clutch Cable, Auger, 47.23”

29. 748-0190

30. 756-0625

Spacer, .508 ID x .75 OD x .68

Roller, Cable

31. 790-00096 Front Guide Bracket, Auger Cable

32. 790-00180 Frame

33. 790-00206 Guide Bracket, Auger Cable

* Found on models with a 22-inch auger housing only

Wheel Assembly

Wheel Size

13 x 4

Rim Only

Tire Only

734-1732

Valve Only

734-0255

Complete

634-04144

634-04151

634-04143

634-04142

13 x 5

15 x 5

734-1527

734-1859

734-0255

NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured

on the previous page are standard equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

MANUFACTURER’S LIMITED WARRANTY FOR

The limited warranty set forth below is given by MTD LLC with respect to

new merchandise purchased and used in the United States, its posses-

sions and territories.

e. MTD does not extend any warranty for products sold or exported

outside of the United States, its possessions and territories, except

those sold through MTD’s authorized channels of export distribution.

“MTD” warrants this product against defects in material and workmanship

for a period of two (2) years commencing on the date of original purchase

and will, at its option, repair or replace, free of charge, any part found to

be defective in materials or workmanship. This limited warranty shall only

apply if this product has been operated and maintained in accordance

with the Operator’s Manual furnished with the product, and has not been

subject to misuse, abuse, commercial use, neglect, accident, improper

maintenance, alteration, vandalism, theft, fire, water, or damage because

of other peril or natural disaster. Damage resulting from the installation or

use of any part, accessory or attachment not approved by MTD for use

with the product(s) covered by this manual will void your warranty as to

any resulting damage.

Normal wear parts are warranted to be free from defects in material and

workmanship for a period of thirty (30) days from the date of purchase.

Normal wear parts include, but are not limited to items such as: batteries,

belts, blades, blade adapters, grass bags, rider deck wheels, seats, snow

thrower skid shoes, shave plates, auger spiral rubber and tires.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH

PROOF OF PURCHASE, through your local authorized service

dealer. To locate the dealer in your area, check your Yellow Pages, or

contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or

call 1-800-800-7310 or 1-330-220-4683 or log on to our Web site at

www.mtdproducts.com.

f. Replacement parts that are not genuine MTD parts.

g. Transportation charges and service calls.

No implied warranty, including any implied warranty of merchant-

ability of fitness for a particular purpose, applies after the applicable

period of express written warranty above as to the parts as identi-

fied. No other express warranty, whether written or oral, except as

mentioned above, given by any person or entity, including a dealer

or retailer, with respect to any product, shall bind MTD. During the

period of the warranty, the exclusive remedy is repair or replacement

of the product as set forth above.

The provisions as set forth in this warranty provide the sole and

exclusive remedy arising from the sale. MTD shall not be liable

for incidental or consequential loss or damage including, without

limitation, expenses incurred for substitute or replacement lawn care

services or for rental expenses to temporarily replace a warranted

product.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, or limitations on how long an implied warranty

lasts, so the above exclusions or limitations may not apply to you.

In no event shall recovery of any kind be greater than the amount of the

purchase price of the product sold. Alteration of safety features of the

product shall void this warranty. You assume the risk and liability for

loss, damage, or injury to you and your property and/or to others and their

property arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original

purchaser or to the person for whom it was purchased as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This limited war-

ranty gives you specific legal rights, and you may also have other rights

which vary from state to state.

This limited warranty does not provide coverage in the following cases:

a. The engine or component parts thereof. These items may carry a

separate manufacturer’s warranty. Refer to applicable manufacturer’s

warranty for terms and conditions.

b. Log splitter pumps, valves, and cylinders have a separate one year

warranty.

c. Routine maintenance items such as lubricants, filters, blade

sharpening, tune-ups, brake adjustments, clutch adjustments, deck

adjustments, and normal deterioration of the exterior finish due to use

or exposure.

IMPORTANT: Owner must present Original Proof of Purchase to obtain

warranty coverage.

d. Service completed by someone other than an authorized service

dealer.

MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683

Download from Www.Somanuals.com. All Manuals Search And Download.

BenQ Projector PB9200 User Manual
Best Ventilation Hood K15 User Manual
Bosch Appliances Cooktop PCL 785 FAU User Manual
Bosch Power Tools Planer 601594039 User Manual
BRK electronic Carbon Monoxide Alarm C05120PDBN User Manual
Broil King Food Warmer NBS 5SP User Manual
Brother Sewing Machine 882 C50 User Manual
Canon Lawn Mower MS 800 User Manual
Carrier Access Network Router SNMP User Manual
Century Stroller PM 0624AB User Manual