Model PRO-9900
Owner’s Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully understand the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera-
tion.
FEATURES :
! 1 Two Way 5 Button Remote Control And 1 One Way 5 Button Remote Control
! Six Channel Code Learning Programmable Receiver
! External Superheterodyne Transceiver Antenna
! Single Or Two User Programmable W/Separate Control Outputs
! Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
! Remote Keyless Entry With Optional Access Guard (must have power door
locks)
! Selectable Manual Override Mode
! New Enhanced Panic Feature (Any button other than unlock stops siren, no
change to the units state)
! Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
! Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect
Off, City Mode)
! Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or
For R/S)
! 24 Hour Time Start Mode
! Cold Temperature Start Mode
! 2 or 4 Hour Automatic Start Mode
! Parking Meter Count Down Timer On LCD Remote
! Additional Count Down Timer Mode
! Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds
To Engage)
! Improved Custom Code Override, User Selectable and Programmable
Page 1
128-7398
1 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
known as a code grabber, which will receive and store the signal from your
keychain transmitter and re-transmit at a later time to disarm your system.
Your Keeloq Code Hopping transmitters will change their signal every time the
button is pressed, so when a thief grabs then re-transmits your signal, the alarm
system will not respond.
If your transmitter button is pressed more than fifty times while it is out of range of
the vehicle (children playing with your keys), the transmitter will not operate when
you return to the vehicle, and will need to be re-aligned to the
receiver. To do this, simply press button 1, (lock), two times within
a one second time period. The system will now respond to that
transmitter each time a button is pressed.
NOTE:
This system is custom configurable and can be set
up to operate with a number of options controlled from any trans-
mitter button or button combination. For reference, we will de-
scribe operation assuming that your system is programmed for
separate lock and unlock buttons. Also reference will be made to
the icons as shown on the buttons left.
NOTE: The LCD based remote will be explained in detail further in
this manual See "System Status" described later in this manual.
Consult your installation center if your system has been config-
ured differently.
NOTE: Your system has the option of using a siren, the vehicle
horn, or both for the sounding device. Where the siren is refer-
enced below, the horn or both may in fact chirp, or beep.
ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid and trunk lid.
2. Press and release Lock/Arm button on the keychain transmitter.
" The dash mounted LED begins to flash slowly.
" Parking Lights flash one time.
" Siren sounds one chirp.
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or
hood lid ajar. Simply close the opened entry point to provide full protec-
tion. If the siren "chirped" three times, sometime after arming, the
exclusive delayed dome light learn circuit has been programmed and
the system detected a open entry point after the learned delay expired.
Again, closing the hood, trunk, or doors will correct the problem and you
do not need to disarm the system to make the correction. If the siren/
horn did not sound when arming, then the chirps have been turned off
and you should refer to the section titled "ELIMINATING THE ARM/DIS-
ARM CHIRPS" in this manual.
# Doors Lock - Optional
NOTE: If the optional Headlamp illumination feature has been added, and has
been selected for operation when arming, as an added convenience, the
system will turn on the headlights when the system is armed.
SILENT ARMING - ACTIVE (Must be activated during programming)
1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.
2. Press and hold the Lock/Arm button on the keychain transmitter for 2
seconds.
Page 3
128-7398
3 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
" The dash mounted LED begins to flash slowly.
" Parking Lights flash one time.
" Siren will not sound.
If the siren "chirped" three times, sometime after arming, the exclusive delayed
dome light learn circuit has been programmed and the system detected a open
entry point after the learned delay expired. Closing the hood, trunk, or doors will
correct the problem and you do not need to disarm the system to make the
correction.
# Doors Lock - Optional
NOTE: If the optional Headlamp illumination feature has been added, and has
been selected for operation when arming, as an added convenience, the sys-
tem will turn on the headlights when the system is armed.
The LCD Remote has the following response:
ARMING THE SYSTEM - PASSIVE (AUTOMATIC)
(Must be activated during programming)
1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and
trunk lid.
" The dash mounted LED begins to flash rapidly, indicating 30 second passive
arming has begun.
2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming and the 30 second passive arm-
ing cycle will re-start when all doors are closed. At the end of the passive
arming cycle;
" The dash mounted LED begins to flash slowly.
" Parking Lights flash one time.
" Siren sounds one chirp
If the siren did not sound when arming, then the chirps have been turned off and
you should refer to the section titled “ELIMINATING THEARM / DISARM CHIRPS“
in this manual.
# Doors Lock - Optional
Door locking during passive arming is a selectable feature. The alarm can be
programmed to allow the doors to lock only when arming using the keychain
transmitter and they will not automatically lock during passive arming.
PROTECTION WHILE THE SYSTEM IS ARMED
" Opening any protected door, hood or trunk lid will cause the alarm to imme-
diately sound. The alarm will continue to sound for 30 seconds, then stop and
continue to monitor all protected entry points. If the thief left a door opened, the
alarm will sound for six 30 second cycles, remain armed and ignore that trig-
gered zone.\
" Whenever the system is armed, the dash mounted LED indicator will slowly
flash. This serves as a visual deterrent to the potential thief. The LED is a very
low current bulb and will not cause the vehicle’s battery to drain, even when left
unattended for extended periods.
" Whenever the system is triggered, the vehicle’s parking lights will flash for the
full 30 second alarm cycle, attracting visual attention to the vehicle.
" Optional - Whenever the system is armed, the vehicle’s starting circuit will be
bypassed. If the thief should choose to ignore the siren, the vehicle can not be
Page 4
128-7398
4 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
started.
" Any mild impact to the vehicle’s glass will cause the alarm to sound a short
series of warning tones.
" Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full
30 second alarm cycle.
NOTE: If the optional interior illumination circuit was installed, the interior light
will flash as well for the full 30 second alarm cycle.
DISARMING THE SYSTEM
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock, to
activate the all door unlock feature operate the Lock/Unlock button a second
time within 3 seconds of the first unlock command.
1. As you approach the vehicle, press and release the Unlock/Disarm button on
the keychain transmitter.
" The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
" Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
" Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before
turning the key on, examine the LED and refer to the INTRUSION WARNING
SIGNALS section of this manual to identify which zone was triggered.
If the siren did not sound when disarming, then the chirps have been turned off
and you should refer to the section titled “ELIMINATING THE ARM / DISARM
CHIRPS“ in this manual.
# Doors Unlock - Optional
# 2 Step Doors Unlock - Optional
NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.
SILENT DISARMING (Must be activated during programming)
Note: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock as
shown, to activate the all door unlock feature operate the Lock/Unlock button a
second time within 3 seconds of the first unlock command.
1. Press and hold button the Unlock/Disarm button on the keychain transmitter for
2 seconds.
" The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
Page 5
128-7398
5 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
automatically. Open any door to suspend the automatic arming.
" Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
" Siren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in your absence.
Before turning the key on, examine the LED and refer to the INTRUSION
WARNING SIGNALS section of this manual to identify which zone was triggered.
# Doors Unlock - Optional
# 2 Step Doors Unlock - Optional
NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.
WHILE THE SYSTEM IS SOUNDING
If during a triggered state, you wish to shut off the siren without disarming your
security system, simply press and release any transmitter button other than the
Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully
armed and protected. This feature is particularly useful if you are aware of children
playing near your vehicle that may accidently trigger your security system. In this
case you can cancel the siren sounding without disarming your alarm.
INTRUSION WARNING SIGNALS
This system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren will
chirp 4 times and the parking lights will flash 3 times when disarming the
system. Enter the vehicle and observe the red dash mounted LED to identify
which zone was triggered.
$ If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to the shock sensor, or an accessory trigger-
ing device that may have been added to the system.
% If the LED is flashing two times...pause...two times...pause...etc., then
an intrusion attempt was made to a hood or trunk pin switch that was
added to the system or to a light activated entry point if the alarm was
installed using the voltage sensing feature.
& If the LED is flashing three times...pause...three times...pause...etc.,
then an intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory and will
only be erased when the ignition key is turned on.
VALET SWITCH
The valet switch allows you to temporarily bypass all alarm functions, eliminating
the need to hand your transmitter to parking attendants or garage mechanics.
When the system is in valet mode, all alarm functions are bypassed, however the
remote panic feature and remote door locks will remain operational. In addition,
the parking lights will flash to indicate locking and unlocking. To use the valet
mode, the system must first be disarmed either by using your keychain transmit-
ter or by activating your personalized manual override code.
1. Enter the vehicle and turn the ignition key to the on position.
2. Press and hold the valet pushbutton switch until the dash mounted
Page 6
128-7398
6 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
LED turns on solid. The system will remain in the valet mode.
3. To return to normal operation, press and release the pushbutton switch
any time the ignition is on.
NOTE: Always remember to return the system to normal operation. This will
ensure that the vehicle remains protected at all times.
MANUALLYOVERRIDINGYOUR SYSTEM:
USING THE VALET SWITCH MANUAL OVERRIDE
Your Security System can be disarmed without the use of the keychain transmitter. This is
necessary, since you will need the ability to operate your vehicle if the transmitter is lost or
its battery fails. If your system has been selected for Valet Switch manual override as
indicated on the last page of this manual, to bypass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the on position.
3. Within 5 seconds, press and release the valet pushbutton switch.
The alarm system will stop sounding and enter the (bypass) mode. You can now
start and operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inopera-
tive.
PROGRAMMING YOUR CUSTOM OVERRIDE CODE:
Unlike override switches easily found, and defeated, this security system allows the
consumer to program a personal override code, offering a higher level of security. To take
advantage of this option, programmable feature # 10 must be selected for the Custom
Code Option. Consult your installation center for programming details. The system
comes from the factory with a pre-programmed override code of 11. To change this
default override code, do the following:
1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence. Turn the ignition switch to the on position.
2. Within 10 seconds, press and release the valet/override switch, 3 times.
3. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off
then on.
6. Within 10 seconds, begin to enter your chosen units digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.
7. Finish by turning the ignition switch to the off position.
If the new code was accepted, the unit will report back the newly entered code, by
flashing the LED, first indicating the 10ths digit, pause and then the units digit.
The unit will report the new code three times with a one second pause between
each code, then the system will begin arming. If the LED flash pattern reports the
previously stored code, the new code was not entered correctly. Please repeat
steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not
recognize a 0 (Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
Page 7
128-7398
7 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Custom Code Programming Example:
To Change the code from the factory pre-assigned code of 11 to “52” you would do
the following:
1. Disarm the system by use of the transmitter or by use of the emergency
override sequence.
2. Turn the ignition switch to the on position.
3. Within 10 seconds, press and release the valet/override switch, 3 times.
4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)
5. Within 10 seconds, begin to press and release the pushbutton switch to set
the tenths digit.
(As per the example, press and release 5 times to set the tenths digit to 5)
6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch
off then on.
7. Within 10 seconds, begin to press and release the pushbutton switch to set
the units digit.
(As per the example, press and release 2 times to set the units digit to 2).
8. Turn the ignition switch to the off position. Immediately observe the LED flash
pattern.
You will note the LED flashing five times, pause, and then flash two times, pause.
This pattern will be repeated three times indicating the new code (52) has been
accepted and stored in memory.
NOTE: If after step 7, the LED flashes a code other than what was just entered,
this indicates that the code has not been changed. You will have to repeat
steps 1 through 7 above being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0
(Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for
more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.
MANUALLYOVERRIDINGYOUR SYSTEM:
USING THE CUSTOM CODE OVERRIDE
Assuming the override code programmed has not been changed, and the default
override code of 11 is in the system's memory.
1. Enter the vehicle and turn the ignition switch to the on position.
NOTE: The siren will sound.
2. Within 5 seconds, press and release the pushbutton switch 1 time.
3. Within 5 seconds, turn the ignition switch off then on.
4. Within 5 seconds, press and release the pushbutton switch 1 time.
5. Turn the ignition switch off then on and start the vehicle.
NOTE: If you have changed the programmed override code then substitute your
new code tenths for step 2 above, and units for step 5 above.
ELIMINATING THE NORMALARM / DISARM CHIRPS
As explained earlier in the manual, you can eliminate the chirps selectively any
time you arm or disarm the system, if the feature has been activated, simply by
holding the ARM or DISARM button for two seconds. If you find the normal arming
and disarming chirps annoying, they can be turned off permanently, eliminating
the need to hold the ARM / DISARM button for 2 seconds. To do this:
Page 8
128-7398
8 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Turn the ignition key on then off.
2. Within 10 seconds, press and release valet switch three times.
3. If the chirps were on before you started, then you will hear two chirps indicat-
ing they have been turned off.
If the chirps were off before you started, then you will hear one chirp indicating
they have been turned on.
NOTE: Whenever the chirps are bypassed, the 4-chirp intrusion indicator
and 3 chirp defective zone indicator will always operate. Since these are
important warnings to you that something has happened, they cannot be
eliminated.
NOTE: Your system must be programmed by the installation center to en-
able this feature.
REMOTE PANIC OPERATION
The Lock or Unlock button on your keychain transmitter also functions as a panic
switch for use in emergency situations. To use remote panic,
1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or
more seconds. The alarm will immediately sound.
2. To stop the alarm, press and hold the Lock or Unlock button on the transmitter
again for 3 seconds. If the button is not pressed, the alarm will automatically
stop after 30 seconds. Also if any transmitter button other than the Lock or
Unlock button is pressed and released, the Panic mode will be turned off
immediately. The normal function of this transmitter button will be suspended
during the Panic sounding period.
3. During the panic mode, the Lock and Unlock buttons can be used to lock and
unlock the doors, (if the option is installed), however once the unlock/disarm
button is pressed, the vehicle's starter inhibit device, (where installed) will be
disabled allowing the vehicle to start.
NOTE: While in the Panic mode, pressing and releasing the Lock or Un-
lock buttons will, if the option is installed, lock and unlock the doors respectively.
While in the panic mode, anytime the Unlock button is pressed, the panic feature
will continue for the allotted 30 seconds, however, the security system will be
disarmed allowing the vehicle to start.
RF SHOCK SENSOR MODE SELECTION
The way in which your alarm system reacts to threatening vibrations, created by
attempts to enter the vehicle by breaking a window, is adjustable by the transmitter
immediately after arming. There are 4 modes of operation that can be selected
by the operator:
1. Normal Operation (default mode)
In this mode, any strong vibrations will cause the siren to sound (full
detect) for 30 seconds. Any lesser vibration will cause the siren to emit
about 6 short warn away chirps, (pre-detect).
2. Stage 1 (Omit pre-detect)
In this mode, the warn away chirps created by the lesser vibration will be
deleted. If strong vibration occurs, the siren will sound.
3. Stage 2 (Omit pre & full detect)
In this mode, both the pre-detect stage and the full trigger stage of the sensor
are defeated. The unit will not react to vibration of any magnitude.
NOTE: Shock Sensor Icon Is Displayed On The LCD Panel.
4. Stage 3 (City Mode)
Page 9
128-7398
9 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
In this mode, the pre-detect chirps will change from six pre-warning tones to
a full 10 seconds of warning chirps.
The full detect trigger duration will be reduced from 30 seconds to 15 seconds.
NOTE: Setting the stage of the shock sensor will be effective for one arming cycle
only. Once the system has been disarmed, the very next arming cycle will
cause the sensor to default to the normal operation stage.
To change or adjust the shock sensor, press and release the ARM button of you
keychain transmitter.
1. Within 2 seconds of arming, press and release the ARM button 1 time, to
defeat the pre-detect stage of the shock sensor. (The lights will flash and the
siren will chirp once.)
2. Within 2 seconds of step 1, press and release the ARM button 2 times, to
defeat the pre and full detect stages of the shock sensor. (The lights will
flash and the siren will chirp twice.)
3. Within 2 seconds of step 1, press and release the ARM button 3 times to
enter the "City Mode" of operation. (The lights will flash and the siren will chirp
three times.)
While under control of the remote start the system can be programmed to allow
you to shunt the shock sensor from the transmitter. If the system has been such
programmed, simply press the lock button of your keychain transmitter anytime
during the remote start cycle. The shock sensor will be shunted for the entire run
cycle and will resume normal operation after the remote start unit shuts off.
Check with your installation center to determine if this feature has been pro-
grammed into your system.
SAFETY (Red Handled ) CONTROL SWITCH
The control switch allows you to temporarily disable the remote starting function
of your system. To disable the unit, move the red handled control switch to the off
position.
The control switch also allows you to select between 2 hour start up and 4 hour
start up when using the automatic start up timer mode. The factory preset start up
time for this mode is every 4 hours. To select between 2 or 4 hour start-up timer:
1. Begin with the control switch in the on position.
2. Turn the ignition switch on then off.
3. Within 10 seconds, move the control switch off, on, off, on (2 switch cycles) to
select a 2 hour start timer. After 10 seconds expire, the parking lights will
flash and the siren will chirp 2 times confirming that the two hour start cycle is
set. Or, within 10 seconds move the control switch off, on, off, on, off, on,
off, on (4 switch cycles) to select a 4 hour start timer. The parking lights will
flash and the siren will chirp 4 times confirming that the 4 hour start timer is
set.
REMOTE STARTING THE VEHICLE
The system WILL NOT start the vehicle if any one of the following conditions
exists:
1. The Vehicle Hood Is Opened.
2. The Gear Selector Is In Any Gear Other Then Park.
3. The Brake Is Depressed.
4. The Safety Control Switch Is In The Off Position.
WARNING! Be certain that the vehicle is outdoors before using this or any remote
vehicle starting device. A running engine produces dangerous carbon
Page 10
128-7398
10 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
monoxide fumes which can be harmful or fatal if prolonged exposure
occurs. DO NOT remote start the vehicle if it is garaged.
To Remote Start The Vehicle:
Press and release the programmed channel of your keychain transmitter two
times within 2 seconds. The vehicle will start and remain running for the pre-
programmed 5, 10, 15, or 20 minutes. As a visual indication, the parking lights
will flash or turn on depending on the programming set up by your installation
center.
When you arrive at your vehicle, disarm the alarm system by pressing and re-
leasing the arm/disarm button of your keychain transmitter. Enter the vehicle and
turn the ignition key to the on position.
CAUTION! Do not turn the key to the start position. This will cause the starter
motor to engage with the already running engine which could result in
damage. Step on the brake pedal to disengage the remote start unit.
The vehicle will continue to run but now on it's own power.
NOTE: The engine will stop running before the expiration of the pre-programmed
run timer if you complete any of the following:
1. Press and release the programmed channel of your keychain transmitter two
times within 2 seconds.
2. Depress the brake pedal.
3. Open the hood.
4. Move the red handled control switch to the off position.
5. Race the engine to above 4000 RPM.
OPERATING ONAUTOMATIC START UP TIMER MODE
Your system has the ability to automatically start the vehicle every 2 or 4 hours
over a 48 hour period. This feature is especially useful in cold climates where
the only means to keep the engine and engine fluids warm is to periodically start
the engine.
WARNING! Be certain that the vehicle is outdoors before using this or any re-
mote vehicle starting device. A running engine produces dangerous
carbon monoxide fumes which can be harmful or fatal if prolonged
exposure occurs. DO NOT remote start the vehicle if it is garaged.
TO BEGIN THEAUTOMATIC START UPTIMER
1.Turn the ignition key on then off.
2. Within 10 seconds, activate the RF start command two times. (Push the
programmed channel button of your keychain transmitter 4 times).
The parking lights will flash and the siren will chirp 4 times indicating the timed
start mode is activated.
The vehicle, on a 2 or 4 hour interval basis, will automatically start, run for
the pre-programmed time (5,10,15 or 20 minutes), and then shut off. This
will continue for 48 hours.
NOTE: The automatic start up timer can also be initiated from the keychain
transmitter. To do this:
1. Start the vehicle using the keychain transmitter by pressing and releasing the
second channel transmitter button 2 times.
2. Shut off the vehicle using the keychain transmitter by pressing and releasing
the second channel transmitter button 2 times.
3. Within 10 seconds of step 2, activate the RF start command two times. (Push
the second channel button of your keychain transmitter 4 times).
Page 11
128-7398
11 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
The parking lights will flash and the siren will chirp 4 times indicating the timed
start mode is activated.
CANCELING THEAUTOMATIC START UPTIMER
To cancel the automatic start up timer do one of the following;
1. Start the vehicle manually with the use of the ignition key and depress the
brake pedal.
2. Remote start the vehicle using your keychain RF transmitter.
NOTE: Option button used in combination is only available on the alternate re-
mote transmitter and not available on the LCD Transmitter.
OPTIONAL DEVICE OUTPUT ( CHANNEL 3 )
Controlled By: Trunk/Key Button
Other Transmitter button configurations are also available. Con-
sult your installation center for other configurations not listed
above that may have been programmed to operate a specific
feature of your system.
This security system is equipped with an output which will acti-
vate when the appropriate transmitter button is depressed for 4
seconds. Although this output is intended to activate the trunk release option,
any other optional devices may be connected to this channel. Consult your
installation center for more information about this output.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )
Controlled By: # Trunk/Key Button # Option Button # Lock + Unlock Buttons #
Lock + Trunk/Key Buttons # Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available. Con-
sult your installation center for other configurations not listed
above that may have been programmed to operate a specific
feature of your system.
This security system has an additional feature that can be con-
nected to a number of different optional accessories. Some of the more common
uses for this channel are;
# Remote Car Starter
# Remote Window Closure
# Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )
Controlled By: # Trunk/Key Button # Option Button # Lock + Unlock Buttons #
Lock + Trunk/Key Buttons # Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available.
Consult your installation center for other configurations not
listed above that may have been programmed to operate a
specific feature of your system.
This security system has an additional feature that can be
connected to a number of different optional accessories.
Page 12
128-7398
12 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Some of the more common uses for this channel are:
# Remote Car Starter
# Remote Window Closure
# Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 6 )
Channel 6 is an alternate output that can be controlled by the unlock button of the
transmitter, or by and independent button or combination of buttons. For your
vehicle this output is:
Controlled By: # Trunk/Key Button # Option Button # Lock + Unlock Buttons #
Lock + Trunk/Key Buttons t# Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available.
Consult your installation center for other configurations not
listed above that may have been programmed to operate a
specific feature of your system.
This security system has an additional feature that can be
connected to a number of different optional accessories. Some
of the more common uses for this channel are:
# Remote Car Starter
# Remote Window Closure
# Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
ADDITIONAL REMOTE FUNCTION ( CHANNEL 7 )
Channel 7 is an alternate output that can be controlled by the unlock button of the
transmitter or by and independent button or combination of buttons. For your
vehicle this output is:
Controlled By: # Trunk/Key Button # Option Button # Lock + Unlock Buttons #
Lock + Trunk/Key Buttons # Unlock + Trunk/Key Buttons
Other Transmitter button configurations are also available.
Consult your installation center for other configurations not
listed above that may have been programmed to operate a
specific feature of your system.
This security system has an additional feature that can be
connected to a number of different optional accessories. Some
of the more common uses for this channel are:
# Remote Car Starter
# Remote Window Closure
# Remote Garage Door Interface
To remotely operate the device indicated, momentarily press, or press and hold
the appropriate transmitter button(s) as indicated above.
TURBO TIMER MODE
This system provides a means to cool down the vehicles turbo charger, if so
equipped, by allowing the vehicle to continue to run for a prescribed period of time
every time the vehicle's engine is turned off. This feature requires the system to be
Page 13
128-7398
13 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
set up for turbo timer during installation. Consult with your installation center to be
certain this feature was activated and how long the vehicle will continue to run, 3,
5, or 10 minutes after the ignition switch is turned off.
To activate the turbo timer:
Anytime the engine is running for more than 15 seconds:
1) Place the gear selector in park.
2) Set the parking, (hand), brake.
3) Be certain your foot is off the brake pedal.
4) Press the program/Push-Button switch 2 times within 5 seconds.
The parking lights will flash two times indicating the mode was successfully
entered.
If your parking lights flashed four times, this indicates the turbo mode was on and
is now turned off.
With the turbo timer mode selected on, after you've arrived at your destination,
while the engine is still running, set the parking brake, pause 2 seconds, then turn
the ignition switch to the off position. The engine will continue to run the allotted
time according to the selection during installation.
If you do not want the vehicle to continue to run for one cycle, simply step on the
vehicle's brake, or release the parking brake, or activate the transmitter's start
button two times in succession. Any of these will cause the engine to turn off.
TELEMATICUPGRADE:
This system has the ability to have a telematic upgrade module connected to it.
This is a upgrade that can give you control of certain functions of your vehicle from
a Telephone, or in some cases a computer interface. Please check with your
installation center for most recent Telematic Upgrades. If you had a Telematic
Upgrade installed, the manual supplied with the upgrade unit will provide a op-
erators manual advising of the features of the system and means available to
control these features of your vehicle.
TRANSCEIVER ICONSAND THEIR INDICATIONS
When Disarmed, Press the Arm/Lock button to Lock and Arm the System. The
Lock Icon is displayed on the LCD panel & the parking lights flash once.
When Armed, Press the Disarm/Unlock button to
Unlock and Disarm the System. The Unlock Icon is displayed
on the LCD panel & the parking lights flash twice.
When the Key Icon Button Has Been Operated for 3 seconds
the trunk open icon will flash on the LED Screen. If text mode
was selected, the words Trunk Open will appear and remainon
the screen until the trunk is shut.
When the Key Icon Button is pressed 2 times in succession
The three puffs of smoke show on the LCD screen. While the
vehicle is running, the exhaust indication will flash and the hour
glass will indicate count down timer based on the 5, 10, 15, or
20 minute run time set up by your installation center. When the
Page 14
128-7398
14 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
unit shuts off the exhaust indication will turn off and the trans-
mitter will play a melody. If text mode was selected, the screen
will scroll the words Engine Running.
Note Engine can be started in many modes armed, disarmed,
valet, etc... The screen shown is Locked/Armed and running.
When Panic Mode has been activated and the system is armed the vehicle's
lights, the lock and the siren icon will flash on the LCD screen. If the system is
disarmed and the Panic Mode is activated, the lights, siren, and the unlock
icons will flash on the LCD screen. If in text mode, the words Panic will flash on
and off until the mode times out and the next remote command is executed.
When ever the vehicle is operated from the two
way transmitter, the unit will beep responsive to
the function executed at the vehicle. 1 beep when
armed, 2 beeps when disarmed, etc... at times It
may be inconvenient or too noisy to hear the beep tones, so the system allows
you to set the unit for vibrate mode. To toggle on or off beep tones/vibrate,
locate this feature in the transmitter program section and set to vibrate. The
icons shown left will appear in the upper left of the screen.
If the alarm system has been triggered, the icon displayed on
the transmitter LCD will indicate which zone has been activated,
as well sound the beep tones, or vibrate dependent upon the
setting as shown above. The following trigger patterns will be
displayed.
Triggered and the entry attempt was made to one of the vehicle
Doors.
Triggered and entry attempt was made to the vehicles Hood
or
Trunk.
Triggered and entry attempt was made to the vehicles glass, or
the vehicle has been hit or bumped hard enough to cause a
response from the vibration detector.
ADDITIONAL ICONS THAT MAYBE DISPLAYEDARE:
If the arm/disarm chirp tones have been turned off at the vehicle,
when you arm, or disarm, the display will indicate this as shown
and there will be no arm/disarm chirps at the transmitter. This is
true if the transmitter is set for vibrate mode.
Page 15
128-7398
15 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
When the vehicle is armed, and a door is opened, or ajar, the transmitter will
chirp 3 times, the lights will flash, and the display will indicate a
door trigger as shown on the previous page. In the text mode
the word Armed, Door Opened will appear. When the door is
closed or the zone clears, the transmitter will chirp 1 time, and
the display will clear.
When the vehicle is armed, and the hood or trunk, is opened or
ajar, the transmitter will chirp 3 times, the lights will flash, and the
display will indicate a hood or trunk trigger as shown on the
previous page. In the text mode, the words Armed Trunk or Hood
Opened will appear. When the hood or trunk is closed, or the
zone clears, the transmitter will chirp 1 time, and the display will clear.
Page 16
128-7398
16 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONALREMOTE FEATURES:
The two way remote control unit allows you to access status
information from the vehicle, check temperature, light the display,
toggle the transmitter from beep tones to vibrate mode, initiate
daily start timer, and temperature start. Selection of these and
other features are shown below:
NOTE: Transmitter must be within operating range of the vehicle,
approximately 1000 ft.
Check Vehicle Status:
Press the lock+key+option buttons simultaneously for 1 second.
The vehicle's alarm will display the systems current status.
Check Temperature: (Only available on certain remote start units)
Press the option+key buttons simultaneously for 1 second. The
vehicle's alarm will display the temperature. Temperature is
read from the alarm's module located below the dashboard. This reading may
be higher than actual ambient temperature due to the greenhouse and is
relative only to the inside vehicle temperature.
Temperature Start Mode:
To toggle this feature on or off, from the armed mode, press the Option &
Unlock Buttons simultaneously, the temperature icon appear on, or
disappear from the display, and the transmitter will emit a tone.
NOTE: This feature must be active in the feature selection menu of your system.
Check with your installing dealer to insure this feature is set to the on position.
Light The Display:
Press and release the "F" (Function) button one time. The display will illumi-
nate for 10 seconds.
Vibrate Or Tones:
While in the transmitter program mode select Vibrate or tone to toggle this
feature on and of.
Daily Start Timer: (Only available on certain remote start units)
Press the option+lock buttons simultaneously for 1 second. The
transmitter will beep and display the 24hr timer. The vehicle will start
automatically when the time set is reached. (See chart for time settings).
Pressing this button combination a second time will toggle this feature off. Note
the transmitter must be within range of the vehicle to set this feature and within
range to cause the vehicle to start at the preset time. The unit will start at the
prescribed time once only. This function must be selected each time you want
the vehicle to start. To activate this function, (a) Turn the ignition switch off. (b)
Within 10 seconds of step (a), depress and hold the brake pedal, while press-
ing the key icon transmitter button 2 times. (c) the unit will emit 2 chirps, the
transmitter will beep and the start timer icon on the display will remain on.
Note this feature must be activated at the vehicle at the prescribed time. Once
activated at the vehicle, you can toggle the feature on simultaneously pressing
the Lock + Option buttons of the transmitter. The 24 hour icon will appear and
Page 17
128-7398
17 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
the transmitter will emit a tone confirming the feature is active.
Note: the unit will start once and run for the prescribed time. If you require more
frequent starting please refer to auto start up timer mode shown earlier in this
guide.
NOTE: To insure accurate 24 Hour Start up, it is advisable to reset the start time
periodically as time may drift slightly each day.
Page Call Out:
From within the vehicle, if the valet push button is pressed for three seconds,
the alarm unit in the vehicle will transmit to the LCD remote and a beep tone
will be heard and a phone icon will be displayed on the hand held transmitter
indicating that someone is calling you to the vehicle.
Count Down Timer:
The unit offers an additional count down timer for situations where an
alert tone may be needed to remind you of something important. For
instance you may have a meeting 4 hours from now and you want a
reminder in 3 Hrs and 45 Mins. This additional count down timer allows you to
set the count down up 99 Hours and 59 Minutes from the current time and
when the timer reaches zero, the transmitter will emit a tone or vibrate depen-
dent on your preferred setting. Set the timer as shown in the transmitter feature
set up section, then to activate the timer, after exiting the transmitter feature
setting mode, press the "F" + Option buttons simultaneously.
Valet:
When the System is in the valet mode, the icon shown will show
in the display when the status check buttons are activated.
Parking Meter Count Down Timer.
The transmitter has a built in timer that can count down from 10, 20, 30, 60, 90,
or 120 minutes. This feature is useful when parking the vehicle in a metered
parking lot. If the time on the parking meter is 30 minutes, you can set the
count down timer to 20 minutes. The transmitter will emit a beep tone when
the timer expires to remind you to get back to your vehicle. To use the parking
meter timer, Press the "F" + Option buttons more than one time. Once activated
the Count Down Timer as described above. Activating the "F" + Option a
second time will set the parking meter count down to 10 minutes, a third time
will set it to 20 minutes, a fourth time will set it to 30 minutes, etc... up to 120
minutes, then the cycle will repeat, countdown activation, 10 minutes, 20
minutes and so on. Once you stop at a setting, the unit will count down and
when it reaches the set time will alert you with a beep tone as a reminder that
you have to get back to the vehicle.
Alarm Clock Mode:
The transmitter has a built in alarm clock that can be set to play a
selectable melody at a certain time each day. The alarm clock mode
must be set as described in the transmitter feature section. To use
this feature please refer to the section on transmitter feature
selections. To toggle this feature on and off once this feature and
the time is selected, simply press the "F" + Trunk/Key button simultaneously to
toggle this feature on and off. An icon will appear or disappear, and a melody
will be played when this mode is activated and deactivated.
Page 18
128-7398
18 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Your system is shipped with two transmitters, 1 two way, shown on the
left and the one way transmitter, shown right. The one and two way transmitters
are programmed from the factory with separate lock & unlock buttons, the trunk/
key icon button operates remote start and remote trunk release
where applicable. The option button and any button
combination may be programmed to operate various
options. Consult your installation center for button
programming and options that may have been added
to your vehicle. Although this is the default program-
ming from the factory, this can be changed for you to
any configuration you prefer. Please refer to the
transmitter program guides included with your kit.
TRANSMITTERFEATURESELECTIONS:
Your system is packaged with a two way confirm-
ing transmitter shown left which can be set for
Icon mode or text mode to indicate the function and status
of your vehicle.
To change modes, press and hold the "F" button for 5 seconds. This puts
the transmitter into the program mode. The program modes lets you select
by pressing the Trunk/Key Icon button to scroll up, or the Option button to
scroll down. Once you come to the selection of choice, press the "F"
button to select the option, and then use the Trunk/Key, Option buttons to
select up or down, or lock/unlock buttons to select left or right choices that
are displayed on the various screens.
To change between text or icon modes, do the following:
1) Press the "F" button for 5 seconds until the transmitter beeps.
2) Press the Trunk/Key button until Homepage Select Set appears.
3) Press "F" to display the selections of text or icons.
4) Use the Trunk/Key or Option buttons to toggle between text or icon
modes.
5) Use the "F" key to select.
6) Press the "F" button for 5 seconds to exit the program mode.
Other features that are selectable or programmable on your two way
transmitter are:
(a) Set to defaults. This returns the transmitter to the factory settings if select yes.
(b) Alarm Trigger History (Will display the last 4 trigger events)
(c) You can assign a Name for an output channel function
(d) You can personalize the Homepage to display name, or have the digital clock displayed
(e) You can select Icon Mode or Text mode
(f) You can select Language of text from English, Spanish or French
(g) Set the temperature readout to display in "Fahrenheit or Celsius
(Only available on certain remote start units)
(h) Set the melody for the Alarm Clock
Page 19
128-7398
19 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
(i) You can set the unit to provide a Tone, or Vibrate upon activation
(j) You can set the Countdown Timer
(k) You can set the Alarm Clock
(l) You can set the Clock
Your transmitter has a battery indicator that is shown in the upper right
corner of the screen as shown left. This icon indicates a new battery
shown with 3 bars. As the battery deteriorates, the bars will disappear. 1
bar indicates the battery should be replaced. Replace battery with a fresh
1.5V AAA battery and dispose of the used battery properly.
Other icons that will be displayed at times when certain functions and
features are active in the vehicle or on the remote:
Range Indicator. The range indicator will have bars to the side of the icon if
the unit is out of range.
Vibrate Mode On, this icon will be displayed if you select vibrate
instead of tones. To toggle vibrate on and off, press "F" + Unlock
simultaneously.
Alarm Clock. This icon will be toggled on and off when the "F" +
Trunk/Key buttons are pressed simultaneously. The feature must be
set in the feature selection menu of the transmitter.
Count Down Timer . This icon is toggled on and off by pressing the
"F" + Option buttons simultaneously. The feature must be set for a
time in the feature selection menu of the transmitter.
Power Save Feature. Press the "F" and Lock buttons simulta-
neously to toggle this feature on and off. With this mode on, the
battery in the transmitter will go into a power down mode when the
unit is disarmed.
24 Hour start Timer. This icon is displayed when the 24 hour start
timer is activated. Press the option+lock buttons simultaneously for 3
second. The transmitter will beep and display the 24hr timer. The
vehicle will start automatically when the time set is reached. (See
chart for time settings). Pressing this button combination a second
time will toggle this feature off. Note the transmitter must be within range of
the vehicle to set this feature and within range to cause the vehicle to start
at the preset time. The unit will start at the prescribed time once only.
This function must be selected each time you want the vehicle to start. To
activate this function, (a) Turn the ignition switch off. (b) Within 10 seconds
of step (a), depress and hold the brake pedal, while pressing the key icon
transmitter button 2 times. (c) the unit will emit 2 chirps, the transmitter will
beep and the start timer icon on the display will remain on.
Temperature Start Mode. This icon will appear when the temp start
mode is activated. The vehicle will start one time automatically when
the temperature reaches 0*. Caution, Be certain vehicle is outside
before activating this mode. To toggle this feature on of off, from the
Locked/Armed mode, press the Option and Lock buttons simultaneously.
(Available on certain remote start models only).
Page 20
128-7398
20 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Throughout this manual you will find screen shots where they apply if using
the two way transmitter. If using the one way transmitter while the two way
transmitter is within range of the vehicle, the two way transmitter will update
it's screen.
Parking Meter Count Down Timer.
The transmitter has a built in timer that can count down from 10, 20, 30, 60,
90, or 120 minutes. This feature is useful when parking the vehicle in a
metered parking lot. If the time on the parking meter is 30 minutes, you can
set the count down timer to 20 minutes. The transmitter will emit a beep
tone when the timer expires to remind you to get back to your vehicle. To
use the parking meter timer, Press the "F" + Option buttons more than one
time. Once activated the Count Down Timer as described above. Activating
the "F" + Option a second time will set the parking meter count down to 10
minutes, a third time will set it to 20 minutes, a fourth time will set it to 30
minutes, etc... up to 120 minutes, then the cycle will repeat, countdown
activation, 10 minutes, 20 minutes and so on. Once you stop at a setting,
the unit will count down and when it reaches the set time will alert you with
a beep tone as a reminder that you have to get back to the vehicle.
Other available options access and Icons that may be displayed on your two
way transmitter:
Check Vehicle Status:
Press the lock+key+option buttons simultaneously for 1 second. The
vehicle's alarm will display the systems current status.
Light The Display:
Press and release the "F" (Function) button one time. The display will
illuminate for 10 seconds.
Page 21
128-7398
21 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
THIS PAGE LEFT BLANK INTENTIONALLY
Page 22
128-7398
22 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
PRO-9900
SYSTEM FUNCTIONS AT A GLANCE
DASH LED INDICATORS
RAPID FLASHING
REARMING
=
PASSIVE ARMING/ACTIVE
SLOW FLASHING
OFF
ON SOLID
3 FLASH...PAUSE
2 FLASH...PAUSE
1 FLASH...PAUSE
=
=
=
=
=
=
ARMED
DISARMED
VALET MODE
INTRUSION ZONE 3
INTRUSION ZONE 2
INTRUSION ZONE 1
SIREN CHIRPINDICATORS
1 CHIRP *
2 CHIRPS *
3 CHIRPS
4 CHIRPS
=
=
=
=
ARM
DISARM
ARM / DOOR OPENED
DISARM / INTRUSION
* These chirps are optional, and can be de - activated.
PARKING LAMP INDICATORS
1 FLASH
=
=
=
ARM
DISARM
DISARM / INTRUSION
2 FLASHES
3 FLASHES
Page 23
128-7398
23 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2005 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, NY 11788
128-7398
Page 24
128-7398
24 of 24
Download from Www.Somanuals.com. All Manuals Search And Download.
|