INSTALLATION INSTRUCTIONS
®
COMPACT CADET 3 - 1.6 GPF ONE-PIECE TOILET
®
COMPACT CADET 3 FloWise™ - 1.28 GPF ONE-PIECE TOILET
Model 2403 – Compact Elongated Right Height™ with Seat
Thank you for selecting American Standard – the benchmark of fine quality for over 100 years. To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be sure
your installation conforms to local codes.
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife
Hacksaw
Regular Screwdriver
Wax Ring/Gasket
Adjustable Wrench
Sealant
Closet Bolts
Tape Measure
Carpenters Level
Flexible Supply Tube
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
ROUGHING-IN DIMENSIONS:
NOTE: Distance from wall to closet flange centerline must be as listed below:
2
3
FINISHED WALL
CLOSET FLANGE
724mm
(28-1/2)
16 6mm
(5/8 1/4)
381mm
(15)
159mm
(6-1/4)
A
C/L OF SEAT POST
HOLES 140mm
(5-1/2) CENTERS
422mm
(16-5/8)
CLOSET BOLTS
724mm
(28-1/2)
419mm
(16-1/2)
SUPPLY
AS
REQ'D
INSTALL CLOSET BOLTS
Install closet bolts in flange channel, turn 90 , and slide
into place 6" (152 mm) apart and parallel to wall.
292mm
(11-1/2)
140mm
(5-1/2)
267mm
(10-1/2)
°
241mm
(9-1/2)
*
FINISHED
FLOOR
C/L OF OUTLET
394mm
(15-1/2)
305mm
(12)
4
5
NUT
WAX RING
WASHER
BOLT
I
FLANGE
SEALANT
INSTALL WAX SEAL
POSITION TOILET ON FLANGE
a. Unplug floor waste opening and install toilet on closet flange so bolts project
through mounting holes.
b. Loosely install retainer washers and nuts. Side of washers marked "THIS
SIDE UP" must face up!
Invert toilet on floor (cushion to prevent damage), and
install wax ring evenly around waste flange (horn), with
tapered end of ring facing toilet. Apply a thin bead of
sealant around toilet base.
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
A S A m e r i c a , I n c . 2 0 0 9
©
7301123-100 Rev. D
Download from Www.Somanuals.com. All Manuals Search And Download.
10
9
ADJUSTMENTS
ARM
TOP
REFILL
TUBE
NIPPLE
a. Adjust water level. Water level
should be adjusted to level indicated
on tank by adjusting float cup.
TANK
LEVER
CRITICAL LEVEL
MARK ("C.L.")
MUST BE
Fig. 9A
See Step 10 for water level adjustment
method.
1" ABOVE
"S"
CLIP
OVERFLOW PIPE
FLOAT
CUP
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 9A) and
take up slack on the chain, and
reinsert on lift rod. Make sure the chain
is not too taught.
FLUSH
VALVE
FILL
VALVE
VALVE
BODY
WATER LEVEL
ADJUSTMENT
ROD
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
ADJUSTABLE
HEIGHT
FLAPPER
SHANK
WASHER
THREADED
SHANK
LOCK NUT
CONE WASHER
PARTS FOR WATER
CONNECTION
(SEE STEP 9)
COUPLING NUT
(HAND TIGHT ONLY)
Diagram 1
11
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
!
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the
tank. This damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
TROUBLESHOOTING
12
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK
SLOWLY, repeat Step 12.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF
NON-USE, it is a signal you are wasting water because:
LEVER LE
BRAS EN
PREMIER
• The end of the refill tube is inserted into overflow pipe, below
water level in tank. Attach refill tube to overflow pipe using "S"
clip provided.
• The flush valve is leaking because it's worn, dirty or misaligned
with tank ball or flapper (replace with a new flapper).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL
OF TANK WATER IS SLOW after valve has been in use for
IMPORTANT: Always
clear sand and rust from
system.
• While holding a
• Replace TOP by engaging
lugs and rotating 1/8 turn
clockwise. MAKE
CERTAIN TIP IS TURNED
TO THE LOCKED
POSITION. VALVE MAY
NOT TURN ON IF TOP IS
NOT FULLY TURNED TO
THE LOCKED POSITION.
some time, Fluidmaster Model 242 Replacement Seal may be
container over the
uncapped VALVE to
prevent splashing, turn
water supply on and off
a few times. Leave
water supply off.
needed.
solutions to toilet problems.
•
Make sure water supply is
off. Remove valve TOP by
lifting arm and rotating top
and arm 1/8 turn
For troubleshooting information please contact:
counterclockwise, pressing
down slightly on cap.
30800 Rancho Viejo Road
San Juan Capistrano, CA 92675
(949) 728-2000 (800) 631-2011
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products. Fluidmaster
shall not be responsible or liable for any damages caused by products used with Fluidmaster valves
that were not manufactured by Fluidmaster, Inc.
©
®
2001 Fluidmaster, Inc.
Registered trademark of Fluidmaster, Inc.
7301123-100 Rev. D
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
FLUIDMASTER
WATER CONTROL
SEAT AND COVER
(INCLUDES MTG. KIT)
FLUSH VALVE
TANK COVER
FLAPPER
ASSEMBLY
SEAT POST
MTG. KIT
COMPACT CADET® 3 ONE PIECE
REPAIR PARTS LIST
NOTE: "XXX" represents color options. Specify when ordering.
1.6 1.28
GPF GPF
TRIP
LEVER
COMPONENT
DESCRIPTION
Tank Cover
Seat - Elongated
Bolt Cap Kit
Trip Lever - Left Hand
Trip Lever - Right Hand
Inlet Valve
Flush Valve - 1.6 GPF
Flapper Assembly - 1.6 GPF
Flush Valve - 1.28 GPF
√
√
√
-
√
√
√
-
735125.XXX0A
5350.110.XXX
034783-XXX0A
738903-XXX0A
738919.XXX0A
738565-409.0070A
738942-1000A
738920-0070A
738942-1010A
-
-
√
√
√
√
BOLT
CAPS
√
√
7381043-400.0070A Flapper Assembly - 1.28 GPF w/Float
TROUBLESHOOTING GUIDE
CORRECTIVE ACTION
PROBLEM
POSSIBLE CAUSE
Does not flush
a. Water supply valve closed.
b. Supply line blocked.
a. Open valve and allow water to fill tank.
b. Shut off water supply, disconnect supply line, and inspect
all gaskets and washers. Reassemble. Also, see Fluidmaster
maintenance (see step 12).
c. Flush valve chain too loose or disconnected.
d. Sand or debris lodged in water control.
c. Readjust chain length as required.
d. Shut off water supply. Remove cap and clean per Step 12.
Poor or sluggish flush
a. Bowl water level too low.
a. Check that refill tube is connected to water control and
inserted into tank overflow without being kinked or damaged.
b. Open supply valve fully. Be sure that proper supply tube size is used.
c. Remove obstruction. Consult a plumber if necessary.
d. Normal supply pressure must be at least 20 psi.
b. Supply valve partly closed.
c. Partially clogged trapway and/or drain pipe and/or vent.
d. Supply pressure too low.
Toilet leaks
a. Poor supply line connection.
b. Poor bowl to tank/floor connection.
a. Review Step 8 of installation procedure.
b. Review Step 4 through 6 of installation procedure.
Toilet does not shut off
a. Flush valve chain too tight, holding flush valve open.
b. Flush valve seat and/or flapper worn or deformed.
c. Sand or debris lodged in water control.
a. Readjust chain length as needed. Review step 9.
b. Replace flapper/flush valve assembly, as needed.
c. Shut off water supply. Remove cap and clean per Step 12.
In Canada:
AS Canada ULC
In Mexico:
In the United States:
American Standard Brands
P.O. Box 6820
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
2480 Stanfield Rd.
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: (800) 387-0369
Piscataway, New Jersey 08855
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Attention: Director of Consumer Affairs
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: (800) 442-1902
7301123-100 Rev. D
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|