8473000H
8474000H
Installation Instructions/Warranty Information
7. With washer positioned in showerhead, attach
showerhead to slide bar by rotating the whole
showerhead clockwise while firmly holding slide
bar in place. Hand tighten only. Once tightened,
rotate showerhead so that the spray settings tab
is positioned along the bottom of the showerhead.
1. Remove old showerhead
with wrench. Clean threads
of shower arm
8. Your shower hose is equipped with a permanently installed
vacuum breaker which is located on the end with the yellow tape.
Remove the yellow tape and bag from hose and insert washer into
hose nut. Connect this end of the hose to the diverter valve located
on the bottom of the slide bar. Hand tighten only. If you install the
wrong end of the hose to the diverter valve, water will not flow to
the hand held shower. Note: The end of the hose that contains the
vacuum breaker will discharge water every time you turn your
shower on or off. This is normal. The water is simply draining out,
and will stop when the water is drained. Do not mistake this for a
leak! Some plumbing codes require a vacuum breaker to protect
your local water supply from the back- flow of water.
2. Apply thread tape (in
a clockwise direction) to
threads of shower arm.
3. The slide bar can be mounted
using the preassembled suction
cup or by using the optional
adhesive pad. The suction cup
can only be used on smooth, flat
surfaces. If your shower wall has
a rough surface, or if there is a
grout line present, then you will
need to use the adhesive pad.
Note: Some tub-surrounds will
9. Remove the bag from the other end of the hose and insert
washer into hose nut. Hand tighten this end of the hose to the
hand held shower.
appear to have a smooth, flat surface,
but will actually have a light texture
that is not noticeable at first. If this is
the case, it will prevent the suction cup
from maintaining a hold, and you will
need to use the adhesive pad. To
remove the suction cup from the slide
bar, rotate suction cup counter clockwise
(while suction cup is facing you), and then
thread on the adhesive pad.
10. Fit hand held shower into mounting bracket by slipping the hose
through the bracket opening and seating the hand held shower
into the bracket.
4. Determine if you want the hand held
shower to be positioned on the right side
or left side of the slide bar. To reposition
the hand held bracket, place fingers
on button while having your thumb
positioned underneath the bracket.
Firmly press the button and rotate the
bracket to the other side of the slide bar.
To adjust the height of the hand held shower: locate the button on
the top of the bracket, then position two fingers on top of the button,
and your thumb on the underside of the bracket. Firmly squeeze the
button and slide the bracket up or down to desired height.
Adjusting the angle of the hand held shower: For a higher angle,
grasp the handle of the handheld shower and push it back to rotate the
bracket away from you. To adjust the angle lower, pull hand held shower
towards you. Turn on water and check for leaks.
5. With screen washer positioned in
mounting nut located on the top of
the slide bar, attach slide bar to
shower arm by rotating mounting
nut clockwise. Hand tighten, then
lightly snug with a wrench. DO NOT
OVER TIGHTEN.
11. The diverter valve located at the bottom of the slide bar directs
the water to the showerhead, hand held, or both at the same time.
•
•
•
To direct water to the showerhead, position lever all the
way to the left.
To direct water to the hand held shower, position lever all
the way to the right.
To direct water to both the showerhead and hand held shower,
position lever in the center.
LIMITED LIFETIME FUNCTION AND FINISH WARRANTY
6. To secure slide bar to wall using
adhesive pad: Make sure wall is clean
and dry. Remove adhesive backing,
and with slide bar centered with
shower arm, firmly press adhesive
pad to wall.
American Standard warrants this product to be free from defects in materials or workmanship for as
long as the original consumer purchaser owns this product. American Standard will provide free of
charge, at it's sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship. Proof of purchase
(original sales receipt) from the original consumer purchaser must be made available to American
Standard for all warranty claims. This warranty is non transferable. It does not apply in the event of
product damage due to the use of other than genuine American Standard replacement parts, installation
error, abuse, misuse or improper care and maintenance (whether performed by a plumber, contractor,
service provider or member of the purchaser's household). The warranty excludes damage due to
aggressive air or water conditions, or harsh or abrasive cleaners and/or materials. This warranty
excludes all industrial, commercial and business usage, whose purchasers are hereby extended a two
year limited warranty (with the exception of solenoid valves and other electronic components which
carry a one year warranty) applying to all other terms of this warranty except duration. This warranty
does not cover labor charges incurred and/or damage sustained in installation, repair or replacement,
nor incidental or consequential damages. This warranty is applicable only to American Standard
showers manufactured after June 1, 1996 and installed in the United States, Mexico and/or Canada. THIS
WARRANTY IS EXCLUSIVELY IN LIEU OF ALL OTHER WARRANTIES, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. This warranty gives
the original consumer purchaser of an American Standard shower specific legal rights which may vary
from state to state or from province to province. In some states or provinces the exclusion or limitation
of incidental or consequential damages is not allowed, so those exclusions may not apply to you.
To secure slide bar to wall using
suction cup: Make sure wall is clean.
Lightly moisten suction cup, and with
slide bar centered with shower arm,
firmly press suction cup to wall.
If you need installation assistance, replacement parts, or
have questions regarding our warranty, please call
our product consultants at: 1-877-283-2664, 8 a.m.-5 p.m., EST,
Monday-Friday, or email us at [email protected]
©2010 American Standard, Inc.
American Standard Companies
1 Centennial Avenue
Piscataway, NJ 08855
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|