7242.XXXW
SERIES WHIRLPOOL
RONDO™
HIGH GLOSS ACRYLIC
SHOWN LESS ALL FITTINGS
INSTALLATION INSTRUCTIONS
1816mm
(71-1/2)
●
RECOMMENDED FITTING
165mm
908mm
(35-3/4)
LOCATION 64 X 279mm
(6-1/2)
(2-1/2 X 11)
THANK YOU...
76mm
(3)
C/L OF DRAIN
for selecting an American Standard bath. Your new
bath is shipped to you after careful inspection. The
whirlpool version is completely assembled with pump,
motor, and system piping. All you need to finish the
installation are your selected fittings and electrical
connections for a whirlpool.
267mm
(10-1/2)
229 X 305mm
(9 X 12)
CUTOUT
PUMP
1067mm
(42)
To insure maximum performance and pleasure from
this product, please follow the instructions and
cautions.
ON/OFF
SWITCH
PROVIDE ACCESS
TO PUMP FOR SERVICE
ON ALL INSTALLATIONS
●
OUTLINE OF
CUTOUT
List of Optional Components (not included):
• Safe-T-Heater 9075.120*
●
LEVELING STRINGER
NOT FOR SUPPORT
SAFE-T-HEATER
REMOVABLE BLANK
C/L OF
OVERFLOW
51mm
(2)
List of Required Components (not included):
• Drain 1583.470*
• Bath Filler*
95mm
(3-3/4)
495mm
(19-1/2)
* see your Home Depot Retailer
83mm
(3-1/4)
546mm
(21-1/2)
ROUGH
38mm
(1-1/2)
FLOOR
INTEGRAL
FEET
38 mm (1-1/2)
TAILPIECE
List of Required Tools and Supplies:
GENERAL SPECIFICATIONS FOR 7242 WHIRLPOOL
71-1/2 x 42 x 21-1/2 In (1816 x 1067 x 546mm)
94 Lbs.(43 Kg.)
INSTALLED SIZE
WEIGHT
Tools
Supplies
• Level
• Nails
818 Lbs.(371 Kg.)
87 Gal. (330 L)
67 Gal. (254 L)
45 x 25 In. (1143 x 635mm)
60 x 30 In. (1524 x 762mm)
14-7/8 In (378mm.)
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
• Tape Measure
• Pipe Wrench
• Slip Joint Pliers
• Screw Driver
• Standard
• Putty
• Caulking (waterproof)
• 1 x 3 or 2 x 2
Stringers
39 Lbs./Sq.Ft. (191 Kgs./Sq.m)
• Drop Cloth
• 20 amp GFI
Outlet
• Cement, Plaster,
Grout
(PROJECTED AREA)
PTS.
CUBE (FT3)
Woodworking Tools
• Personal Safety
Equipment
30.3
58.7
WHIRLPOOL ELECTRICAL SPECIFICATIONS
PUMP
2.1 HP, 14.4 AMPS,120.
• Caulking Gun
GENERAL INSTALLATION INFORMATION
Carefully uncrate and inspect your new bath for any shipping damage. If such damage is found, report it to your vendor
immediately.
After inspection and during installation, protect the bath from construction damage. After installation, and before
enclosing with wallboard, tile, etc., water test the unit and check for leaks.
Do not make modifications to the whirlpool system or remove pump from factory mounting. This could adversely affect
the safety and performance of the whirlpool and void the warranty. Do not handle or move the whirlpool by the pump,
motor, or piping system.
Fittings (bath filler, shower arm, etc.) are not provided with the bath and must be ordered separately. Framing and
enclosing materials are provided by others. Check for availability of optional American Standard wall tiling bead
(required for recess installations).
Protect all finished surfaces of the whirlpool during construction and installation using a drop cloth.
WARNING! Do not lift whirlpool by the piping harness at any time.
FOR AFTER-SALES SERVICE CALL 1 (800) 442-1902 WEEKDAYS.
© American Standard Inc. 2003
All product names listed herein are trademarks
of American Standard Inc. unless otherwise noted.
751709-100 REV. L
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL INSTALLATION INSTRUCTIONS
All wiring must be performed by a licensed electrician in accordance with the national electrical code and all other
applicable codes.
WARNING:
When using electrical products, basic precautions should always be observed, including the following:
1. DANGER: RISK OF ELECTRIC SHOCK
Connect only to a circuit protected by a ground-fault circuit interrupter.
2. Grounding is required. The unit should be installed by a licensed electrician and grounded.
3. Install to permit access for servicing.
4. All building materials and wiring should be routed away from the pump body and heater (if equipped).
The whirlpool should be installed on a 120 vac, 20 amp dedicated circuit. The circuit should be hard-wired from the
electrical power supply panel. The circuit must be a three (3) wire circuit from the electrical supply panel. A grounded
neutral wire and a third wire, earth ground, are essential. ADDING THE SAFE-T-HEATER REQUIRES A SEPARATE
15 AMP MAXIMUM GFCI CIRCUIT.
ELECTRICAL INSTALLATION
20 AMP GFCI
OUTLET
WHIRLPOOL MOUNTED
120 VAC
ELECTRONIC
SWITCH
PUMP/MOTOR
GND.
ELECTRICAL DIAGRAM
READ AND FOLLOW ALL INSTRUCTIONS
(3)
751709-100 REV. L
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRE SELECTION GUIDE
Maximum distance from
fusebox to motor
The sizes shown on this
chart are recommendations
for copper conductors
only. Always follow
local and national
Motor
Hi Performance
Rating
50'
100'
120V Power Line
10
150'
200'
electrical codes
2.1
12
8
8
DRAIN CONNECTION AND SYSTEM TEST
Using recommended drain opening, connect whirlpool drain to waste line. Tighten all drain joints securely. Check the
pump couplings and make sure they are hand-tight. Clean the whirlpool and fill with water to a point 2" above the top of
the highest jet. Recheck the pump couplings and make certain that they are not leaking. (Although the pump couplings
are factory tightened and inspected, some loosening may have occured during transit.) Make sure the whirlpool is
connected to the electrical supply and turn the whirlpool on. Check for leaks around all piping connections while the
whirlpool is running.
POST INSTALLATION CLEAN-UP
Remove all construction debris from bath. Tile grout can be removed with a wooden popsicle stick or tongue depressor.
Do not use wire brushes or any other metal implement on bath surface.
Post installation clean-up generally can be completed using warm water and liquid dishwashing detergent. Stubborn dirt or
®
stains may be removed using granular Spic and Span mixed with water.
Painter's naphtha can be used to remove excess adhesives and/or wet oil-base paint.
HARSH CHEMICALS SHOULD NEVER BE USED ON ACRYLIC SURFACES.
Abrasive cleaners must not be used since they will scratch and dull the surface. Dulled areas can be restored by rubbing
with a white automotive-type polishing compound and waxing with a liquid wax.
®
(4)
SPIC AND SPAN IS A REGISTERED TRADEMARK OF PROCTER & GAMBLE
751709-100 REV. L
Download from Www.Somanuals.com. All Manuals Search And Download.
|