SWITCHER
MANUAL PART NUMBER: 400-0378-004
SW1956CT
2–IN, 1–OUT TWISTED PAIR
AUTO-SWITCHER
USER’S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
1.4 CLEANING
PRECAUTIONS / SAFETY WARNINGS
1
·
Unplug the SW1956CT power cord before
cleaning. Clean surfaces with a dry cloth. Never
use strong detergents or solvents such as
alcohol or thinner. Do not use a wet cloth or
water to clean the unit.
Please read this manual carefully before using your
SW1956CT Switcher. Keep this manual handy for
future reference. These safety instructions are to
ensure the long life of your SW1956CT and to
prevent fire and shock hazards. Please read them
carefully and heed all warnings.
1.5 FCC NOTICE
1.1 GENERAL
·
·
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
·
Qualified ALTINEX service personnel or their
authorized representatives must perform all
service.
1.3 INSTALLATION
·
For best results, place the SW1956CT on a flat,
level surface. Keep in a dry area away from dust
and moisture.
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable
protection against harmful interference when the
·
To prevent fire or shock, do not expose this unit
to water or moisture. Do not place the
SW1956CT in direct sunlight, near heaters or
heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can
harm internal components.
equipment is operated in
a
commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions found herein, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the
user will be required to correct the interference
at his own expense.
·
·
Handle the SW1956CT carefully. Dropping or
jarring can damage internal components.
Do not place heavy objects on top of the
SW1956CT. If the unit is to be mounted to a
table or wall, use only ALTINEX-made mounting
accessories.
·
Any changes or modifications to the unit not
expressly approved by ALTINEX, Inc. could void
the user’s authority to operate the equipment.
·
To turn off the main power, be sure to remove
the cord from the power outlet. The power outlet
socket should be installed as close to the
equipment as possible, and should be easily
accessible.
·
·
Do not pull the power cord or any cable that is
attached to the SW1956CT Switcher.
If the SW1956CT is not to be used for an
extended period, disconnect the power cord
from the outlet.
400-0378-004
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
ABOUT YOUR SW1956CT
2
TECHNICAL SPECIFICATIONS
3
Specifications are subject to change.
SW1956CT
2-In, 1 Out Twisted Pair Auto-Switcher
FEATURES/
SW1956CT
The SW1956CT is a 2-In, 1-Out Twisted Pair
Auto-Switcher. The SW1956CT switches
DESCRIPTION
Inputs
automatically upon signal detection, but may also
be controlled manually. The SW1956CT is
designed to switch ALTINEX Twisted Pair
transmitter and receiver signals. These include
ALTINEX part numbers DA1930CT, DA1931CT,
MT103-122, MT103-123, etc.
Input Connector
Power
RJ-45 female (2)
2.5mm DC jack (1)
Outputs
Output Connector
Compatibility
RJ-45 female (1)
The unit is encased in a solid metal enclosure and
ships with an external, 9V power adapter. Also
included is an external contact-closure switch for
manual override of input selection.
ALTINEX Standard for
Twisted Pair
Signal Types
Manual override switching is made via a contact
closure on the Input Select jack. This switch may
be used for manual control, or the contact closure
may be controlled from a control system.
Video Signal
Resolutions
VGA through UXGA,
480p through 1080i
VGA:
640x480@60Hz
900 ft (274 m)
The SW1956CT is perfect for applications that use
wall or floor plates for auto-switching. The
SW1956CT may be mounted to furniture or other
suitable surfaces using optional hardware.
Recommended Max.
Cable Lengths
XGA:
1024x768@60Hz
700 ft (213 m)
Note: Measurements
made using ALTINEX
low-skew cable,
SXGA: 1280x1024@60Hz
650 ft (198 m)
The latest generation of Twisted Pair devices uses
an innovative, patented technology* developed by
ALTINEX. The new signal processing technology
allows transmitting and receiving fully equalized
computer video signals, stereo, and audio signals
over long distances.
CB3150PV.
UXGA: 1600x1200@60Hz
600 ft (183 m)
Accessories Included
Power Adapter
+9 VDC, 500 mA
Contact Closure
* US Patent 7,065,190
Remote Switch
Table 1. SW1956CT General
400-0378-004
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
SW1956CT
MECHANICAL
Material
SW1956CT
0.100 in Al
ELECTRICAL
Input Signal
Finish
Gray
Analog Signal
1.0 Vp-p max
Height
3.000 in ( 76 mm)
4.380 in (111 mm)
1.000 in ( 25mm)
0.40 lb (0.18 kg)
2.00 lb (0.91 kg)
10°C-35°C
Output Video Signals
Analog Signal
Width
1.0 Vp-p max
Depth
Frequency Compatibility
Horizontal
Weight
15-200 kHz
20-190 Hz
Ship Weight
T° Operating
T° Maximum
Humidity
Vertical
Cross-talk
-40 dB @ 10 MHz
DC
Coupling
50°C
Power Consumption
External Adapter: 9 VDC
90% non-condensing
40,000 hrs (min.)
MTBF (calculations)
350 mA (3 W max.)
Table 2. SW1956CT Mechanical
Table 3. SW1956CT Electrical
400-0378-004
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
PRODUCT DESCRIPTION
4
400-0378-004
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
APPLICATION DIAGRAMS
DIAGRAM 1: TYPICAL SETUP
5
ALTINEX includes a remote control switch with the SW1956CT. The remote switch has a 6 ft cable and
may used to control the switcher manually.
When the remote control switch is connected to the INPUT SELECT jack, INPUT 1 will be selected if the
channel select contact is closed. INPUT 2 will be selected if the channel select contact is open.
The switching will be identical whether there are one or two active signals. The LEDs located next to the
input ports indicate which input is selected.
SW1956CT
400-0378-004
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
DIAGRAM 2: INTERNAL VIEW
CONTACT
CLOUSURE
SIGNAL
DETECT
INPUT1
OUTPUT
TWISTED
PAIR
TWISTED
PAIR
INPUT1
INPUT2
RJ-45
RJ-45
INPUT2
POWER
SUPPLY
2.5 mm
9 VDC, 500 mA
400-0378-004
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
INSTALLING YOUR SW1956CT
6
OPERATION
7
Step 1. Connect the ALTINEX power adapter that
There are no settings to adjust on the SW1956CT
Auto-Switcher. The SW1956CT will operate
successfully as long as cables are attached
properly and other technical specifications are
followed.
is supplied with the unit to the power port.
CAUTION: The POWER port and the
INPUT SELECT port use the
same connector type. Make
sure the power adapter is
connected to the POWER
port.
AUTO-SWITCH MODE
The SW1956CT automatically selects the INPUT 2
port if there are no active signals present. If there is
an active signal on INPUT 2 and not on INPUT 1,
then the SW1956CT will maintain INPUT 2 as the
active port. However, when an active signal is
applied to INPUT 1, the SW1956CT will switch to
INPUT 1.
Step 2. The POWER LED and the INPUT 2 LED
should turn on.
Step 3. Connect the SW1956CT inputs to the
outputs of the Twisted Pair transmitters.
Step 4. Connect a cable from the output port of
the SW1956CT to the input port of the
Twisted Pair receiver.
If there are active signals on INPUT 1 and
INPUT 2, the SW1956CT will automatically switch
to INPUT 1.
Step 5. If the remote control switch is to be used,
MANUAL SWITCH MODE
connect it to the INPUT SELECT port.
Manual override is accomplished via a contact
closure on the INPUT SELECT jack. Manual Switch
Mode disables auto-switching.
CAUTION: The POWER port and the
INPUT SELECT port use the
same connector type. Make
sure the control switch is
connected to the INPUT
SELECT port.
Included with the SW1956CT is an external manual
switch with a 6 ft cable. This switch may be used
for manual control, or the contact closure may be
made from a control system. This port uses a
2.5 mm mini-coaxial remote-control jack and it is
located next to the Twisted Pair output.
Step 6. Verify that the picture quality on the
display is good. If a signal is not being
received, make sure that the display is
compatible with the resolution of the
computer graphics card.
INPUT 1 will be selected when the remote control
switch is connected to the INPUT SELECT jack and
the contact is closed. INPUT 2 will be selected if
the contact is open.
CAUTION:
The connector used for the INPUT
SELECT port is the same type as is
used for the POWER connector. Use
caution to ensure the switch is
connected to the correct port.
400-0378-004
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
Cause 2: The signal is not active or is
improperly formatted.
TROUBLESHOOTING GUIDE
8
We have carefully tested and have found no
problems in the supplied SW1956CT unit.
However, we would like to offer the following
suggestions:
Solution 1: Remove the input signals from the
switcher. If the IN 2 LED is off, call
ALTINEX at (714) 990-2300. If the
IN 2 LED is on, see Solution 2.
8.1 POWER LED IS OFF
Solution 2: Connect a properly formatted signal
from an ALTINEX Twisted Pair
transmitter to INPUT 1. If the
switcher does not switch to
INPUT 1, see Solution 3.
Cause 1: The power adapter is installed
wrong.
Solution 1: Make sure the adapter output is
connected to the POWER input jack
on the unit. Check the unit carefully.
The POWER input jack and the
INPUT SELECT jack are the same
type. If the POWER LED is still not
on, see Solution 2.
Solution 3: Bypass the switcher and connect the
output of the transmitter directly to
the input of the receiver. If the
display is good, then call ALTINEX
at (714) 990-2300.
Solution 2: Make sure the adapter is plugged
into a proper AC outlet that has
power. If the adapter has AC power
and the POWER LED is still off, see
Cause 2.
8.3 NO DISPLAY
Cause 1: The source has a problem.
Solution: Check the source and make sure
that there is a signal present and all
source connections are correct. If
the source is working and there is
still no display, see Cause 2.
Cause 2: The wrong power adapter is
installed.
Solution 1: Please use the ALTINEX supplied
external adapter (9 V, 500 mA). If
Cause 2: Manual override is on.
the POWER LED is still not on,
Solution: Make sure there is nothing
connected to the INPUT SELECT
port on the switcher. If there is
nothing connected, see Cause 3.
please
call
ALTINEX
at
(714) 990-2300.
8.2 UNIT DOES NOT AUTO-SWITCH
Cause 3: Signal is bad or missing.
Cause 1: The manual override switch is
installed.
Solution 1: Make sure the switcher output is
connected to the Twisted Pair
receiver input and the receiver is on.
If there is still no display, see
Solution 2.
Solution: Remove the connection to the
INPUT SELECT jack on the unit. If a
plug is installed in the jack, the
SW1956CT will not auto-switch
properly. If the unit does not
auto-switch with the plug removed,
see Cause 2.
Solution 2: Remove both inputs to the switcher
and connect the active signal from
the Twisted Pair transmitter output
to INPUT 2. If there is still no
display, see Solution 3.
400-0378-004
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SWITCHER
Solution 3: Bypass the switcher and connect the
output of the transmitter directly to
the input of the receiver. If the
display is good, then call ALTINEX
at (714) 990-2300. If there is still no
display, see Cause 4.
ALTINEX POLICIES
9
9.1 LIMITED WARRANTY/RETURN POLICIES
Please see the ALTINEX website at
www.altinex.com for details on warranty and
return policies.
Cause 4: Cable connections are incorrect.
9.2 CONTACT INFORMATION
ALTINEX, Inc.
Solution: Make sure that cables are properly
connected. Also, make sure that the
continuity and wiring are good. If
there is still no display present, see
Cause 5.
592 Apollo Street
Brea, CA 92821 USA
TEL: 714 990-2300
Cause 5: The display has a problem.
TOLL FREE: 1-800-ALTINEX
WEB: www.altinex.com
E-MAIL: [email protected]
Solution: Make sure the display is powered
and is turned on. If there is still no
display, please call ALTINEX at
(714) 990-2300.
400-0378-004
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|