OWNER'S MANUAL
EQ
ROCK
TRACK
CLAS
RND SCAN RPT
POP
ACD-84
AM/FM/MPX RADIO WITH MOTORIZE
FOLD-DOWN DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER,
CD CHANGER CONTROLS,
WIRELESS REMOTE CONTROL
AND QUARTZ CLOCK
Download from Www.Somanuals.com. All Manuals Search And Download.
TOLL-FREE INSTALLATION ASSISTANCE
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do,
we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and
hours shown (U.S.A. and Canada only).
TIME ZONE
MOUNTAIN
DAY
PACIFIC
CENTRAL
EASTERN
MON. - FRI.
SATURDAY
8:30AM - 7PM
9AM - 5PM
7:30AM - 6PM
8AM - 4PM
5:30AM - 4PM
6AM - 2PM
6:30AM - 5PM
7AM - 3PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
NUT (5MM)
PERFORATED STRAP
EXISTING DASH OPENING
FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE
NOTE:IFDASHISSOLID, USEREARSIDE(WITHOUTTHELIP)OF
MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
FASTEN THIS END TO SCREW
STUD ON REAR OF CHASSIS
BEND TOP
TABS UPWARD
SCREW
(5MM)
BEND BOTTOM
TABS DOWNWARD
RADIO
SCREW STUD
NUT (5MM)
MOUNTING SLEEVE
FASTEN THIS END TO SECURE PART OF DASHBOARD.
DRILL HOLE IF NECESSARY.
REMOVALTOOLS
CAUTION:
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS
MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE
THE UNIT IS MOUNTED WITHIN THIS LIMITATION.
FOLD-DOWN
DETACHABLE
FRONT PANEL
20° MAX.
SIDE VIEW
OF
FRONT PANEL
CHASSIS
ISO INSTALLATION
TYPICAL INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE FRONT OF
THE CHASSIS BY CAREFULLY UN-SNAPPING IT.
MAXIMUM
SCREW SIZE
M5 x 8
UN-SNAP AT 2 PLACES
EACH ON TOP AND BOTTOM
MAXIMUM
SCREW SIZE
M5 x 8
PLASTIC FRAME
2
FACTORY MOUNTING
BRACKETS
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER WIRING
RADIO WIRING
REFER TO PAGE 4 FOR SPEAKER WIRING
AUTOMATIC
ANTENNA
ANTENNA
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED TO
FUSEBLOCK
REMOTELY ACTIVATE AN AUTOMATIC
ANTENNAORANEXTERNALAMPLIFIER
(SEE ANTENNAORAMPLIFIERMANUAL)
EXISTING
ANTENNA
CABLE
“RADIO”FUSE
+12VACCESSORY
RED(0.5AMP.FUSE)
SCREW
BLACK
METAL PART OF DASH
(DRILLHOLEIFNECESSARY)
CARBATTERY
YELLOW(15AMP. FUSE)
IMPORTANT
YELLOW WIRE MUST BE
CONNECTEDASSHOWNOR
RADIO WILL NOT OPERATE
PROPERLY
FILTER/FUSE
BOX
CONTAINS:
ONE 0.5 AMP FUSE
ONE 15 AMP FUSE
POSITIVE(+)TERMINAL
12 VOLT BATTERY
4-PINPLUGS
9PINPLUG
(SEEPAGE4FORSPEAKERWIRING)
ANTENNALEAD
ONREAROFRADIO
CDCHANGERLEAD
ON REAR OF RADIO
(SEE PAGE 4)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEAKER WIRING
REFER TO PAGE 3
FOR RADIO WIRING
WARNING!
lTHE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
lNEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
lNEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
lFAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL
NOTE:
RCA LINE OUT JACKS
FOR USE WITH OPTIONAL
EXTERNAL AMPLIFIERS
THIS RADIO WILL CONTROL RAMPAGE CD
CHANGER MODELS. CHECK WITH YOUR RAM-
PAGE AUDIOVOX CAR STEREO SPECIALIST OR
CALL 1-800-645-4994 FOR RECOMMENDATIONS
OFOTHERMODELSTHATWILLWORKWITHYOUR
RADIO.
OPTIONALCDCHANGER
RADIO
6
CO
M
P
AC
T
DINCABLE
(SUPPLIEDWITHCD
CHANGER)
CDCHANGERLEAD
ON REAR OF RADIO
9-PINPLUGS
4-PINPLUGS
SEE PAGE 3 FOR
RADIOWIRING
LEFTFRONTSPEAKER
RIGHTFRONTSPEAKER
GRAYw/BLACKSTRIPE
WHITEw/BLACKSTRIPE
GRAY
VIOLET
WHITE
GREEN
GREENw/BLACKSTRIPE
VIOLETw/BLACKSTRIPE
HELP!
1-800-645-4994
Monday - Friday 8:30am - 7:00pm Eastern
Saturday 9:00am - 5:00pm Eastern
4
LEFTREARSPEAKER
RIGHTREARSPEAKER
Download from Www.Somanuals.com. All Manuals Search And Download.
17, 28, 29
(BEHIND PANEL)
3, 4, 5, 6, 7
14
2
15
26 27
30
8
EQ
ROCK
CLAS
POP
25
TRACK
9
RND SCAN RPT
11
21
36
22
37
20
23
38
12
31
16
32
1
24
33
10, 18, 19, 34, 35
13
3
AUDIO SELECT (SEL) CONTROL
BUTTON
1
ON-OFF POWER BUTTON ( PWR )
Press this button to turn the unit on or off. If
the ignition switch is “on”, the unit will also
turn on automatically when a compact disc is
inserted, or if the MODE switch or BAND
switch is pressed.
This button is used to select the audio
function (volume, bass, treble, balance, or
fade) whose setting is adjusted using the
AUDIO CONTROL knob 2. Pressing the
SEL button once will set the unit for bass
adjustment (BAS will appear on the display
panel) and an audible beep will occur.
Pressing the button additional times will
select treble adjustment (TRE on the
display), balance (BAL), or fader (FAD),
each accompanied by a beep tone. The
display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
2
AUDIO CONTROL UP/DN KNOB
To increase the volume level, turn the knob
clockwise in the UP direction. The volume
will increase and the level will be shown on
the display panel from a minimum of VOL
00 to a maximum of VOL 39. To decrease
the volume level, turn the knob counter-
clockwise in the DN direction. The dis-
play will automatically return to the normal
indication 5 seconds after the last volume
adjustment or when another function is ac-
tivated. This control knob is also used in
conjunction with the AUDIO SELECT (SEL)
while the Equalizer function
NOTE: Bass and Treble cannot be acdujusted
is in
ROCK, CLAS or POP mode.
button
3
to adjust the bass, treble, bal-
4
BASS CONTROL
To adjust the bass level (equalizer function
ance and fader levels as described in
4
,
5
5
,
6
and
7
.
pressing the SEL button so the BAS
inactive), first select the 3Bass mode by
Download from Www.Somanuals.com. All Manuals Search And Download.
indication appears on the display panel.
Within 5 seconds of choosing the Bass
mode, rotate the AUDIO CONTROL knob
display panel from BAL L16 (full left) to BAL
R16 (full right). When the volume level
between the left and right speakers is equal,
BAL 00 will be shown on the display panel.
The display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
2
in the DN direction to decrease the bass
response, or in the UP direction to increase
it as desired. The level will be shown on the
display panel from a minimum of BAS -12
to a maximum of BAS +12 (BAS 00
indicates flat response). The display will
automatically return to the normal indication
5 seconds after the last adjustment or when
another function is activated.
7
FRONT/REAR FADER CONTROL
To adjust the front-rear speaker balance, first
select the Fader mode by pressing the SEL
button
3
so the FAD indication appears on
5
TREBLE CONTROL
To adjust the treble level (equalizer function
inactive), first select the Treble mode by
the display panel. Within 5 seconds of
choosing the Fader mode, rotate the
AUDIO CONTROL button
2
in the DN
pressing the SEL button
3
so the TRE
direction to adjust the front-rear speaker
balance to the rear speakers or the UP
direction to adjust it to the front speakers.
The fader position will be shown on the
display panel from FAD R16 (full rear) to FAD
F16 (full front). When the level between the
front and rear speakers is equal, FAD 00
will be shown on the display panel. The
display will automatically return to the
normal indication 5 seconds after the last
adjustment or when another function is
activated.
indication appears on the display panel.
Within 5 seconds of choosing the Treble
mode, rotate the AUDIO CONTROL knob
2
in the DN direction to decrease the treble
response or the UP direction to increase it
as desired. The level will be shown on the
display panel from a minimum TRE -12 to a
maximum of TRE +12 (TRE 00 indicates flat
response). The display will automatically
return to the normal indication 5 seconds
after the last adjustment or when another
function is activated.
8
LOUDNESS CONTOUR (LOUD)
6
LEFT/RIGHT BALANCE CONTROL
To adjust the left-right speaker balance, first
When listening to music at low volume
levels, this feature will boost the bass and
treble ranges to compensate for the
characteristics of human hearing. Press the
button momentarily to activate this feature;
the LOUD indication will appear on the
display panel. Pressing the button again
momentarily will deactivate the feature (the
LOUD indication will disappear from the
display panel).
SEL button
select the Bal3ance mode by pressing the
so the BAL indication
appears on the display panel. Within 5
seconds of choosing the Balance mode,
rotate the AUDIO CONTROL knob
2
in the
DN direction to adjust the stereo balance to
the left channel speakers or the UP direction
to adjust it to the right channel speakers.
The balance position will be shown on the
6
Download from Www.Somanuals.com. All Manuals Search And Download.
bn
PRE-SET SCAN (PS)
AUTO-STORE TUNING (AS)
9
AM/FM CHANNEL SELECTOR
(BAND)
Press this button momentarily to scan the
stations pre-set into the six memories of the
current band in use. The unit will stop at each
pre-set station for 5 seconds before
continuing to the next pre-set station (the
pre-set number on the display panel will flash
during Pre-Set Scan operation). Press the
button again momentarily to stop Pre-Set
Scan operation and remain on the selected
frequency. If no buttons are pressed during
the scan, the unit will return to the original
station before the scan started.
Each time this button is pressed, the radio
band is changed. The indication AM1, AM2,
FM1, FM2 or FM3 will appear on the display
panel according to your selection.
-
bl
TUNE/SKIP/TRACK (+
BUTTONS
/
)
To manually select a radio station,
momematrily press the Up Tuning (
)
+
button to advance the unit higher, or the
-
Down Tuning (
) button to tune lower
within the selected band.
Pressing and holding the button for longer
than 2 seconds will activate the Auto-Store
Tuning feature which will automatically scan
and enter up to 6 stations into the pre-set
memories on the band in use. If you have
already set the pre-set memories to your
favorite stations, activating the Auto-Store
Tuning feature will erase those stations and
enter the new ones. This feature is most
useful when traveling in a new area where
you are not familiar with the local stations.
Pressing either button for longer than 0.5
second and then releasing will activate the
Automatic Skip Tuning function. The radio
will skip over weaker stations in the selected
direction and stop at the strongest frequency.
The Seek function can be stopped by
pressing the button again or by activating any
other tuning function.
bm
FM MONO/STEREO BUTTON (MONO)
During FM radio operation, this button is used
to select mono or stereo reception of the
broadcast signal. Under normal reception
conditions, the unit should be left in the
stereo mode as indicated by the ST
indication on the display panel when tuned
to an FM stereo signal. If the stereo signal
is too noisy for comfortable listening, press
the FM Mono/Stereo Selector button to
switch to mono reception (the ST
indication will disappear from the display
panel). To return to stereo reception mode,
press the button again so that the ST
indication appears in the display panel.
bo
STATION PRE-SET MEMORIES
To set any of the 6 pre-set memories in each
band, use the following procedure:
1. Turn the radio on and select the desired
band.
2. Select the first station to be pre-set
using the Manual TUNE or Automatic
SEEK Controls bl.
3. Press the pre-set button to be set and
continue to hold it in for
approximately 2 seconds. The
preset number, followed by CH
(channel) will appear on the display
7
Download from Www.Somanuals.com. All Manuals Search And Download.
panel and two beeps will sound,
indicating that the station is now set
into that pre-set memory position. The
station can now be recalled at any time
by pressing that button.
br
MODE SELECTOR (MODE)
This button is used to select the radio or
CD player playback mode. Each press of
the button will select a different mode as
indicated on the display panel.
4. Repeat the above procedure for the
remaining 5 pre-sets on that band and
for the other 4 bands on the unit.
During CD player operation, this button
may be used to change to radio or CD
player mode without ejecting the disc.
bp
LIQUID CRYSTAL DISPLAY PANEL The
IN indication will remain on the
display panel. When returning to CD player
mode, disc play will resume from the point
at which it was stopped.
The Liquid Crystal Display (LCD) panel
displays the frequency, time, and activated
functions.
NOTE: It is a characteristic of LCD panels
that, if subjected to cold
temperatures for an extended period
of time, they may take longer to
illuminate than under normal
conditions. In addition, the visibility
of the numbers on the LCD may
slightly decrease. The LCD read-
out will return to normal when the
temperature increases to a normal
range.
bs
DISC SLOT
With the front panel in the fold-down position,
gently insert the disc into the slot (label
surface facing up) until the soft-loading
mechanism engages and pulls the disc in.
The LOAD indication will momentarily
appear on the display panel followed by the
total playing time of the disc. The (
indication illuminates and becomes
animated, the IN symbol lights, and
the track number and elapsed time will appear
on the display panel.
)
CAUTION: This unit is designed for play of
standard 5" (12cm) compact
discs ONLY. Do not attempt to
use 3" (8cm) CD-Singles in this
unit, either with or without an
adapter, as damage to the player
and/or disc can occur. Such
damage will not be covered by
the Warranty on this product.
bq
LEVEL METER DISPLAY
This display consists of a five-bar graph
which provides a visual representation of the
volume level and the left and right channel
audio signal levels. The volume level is
represented by the two outer bar graphs and
the center graph. As the volume is
increased, the number of illuminated
segments will increase. The left and right
channels are represented by the respective
inner bar graphs whose illuminated
segments increase and decrease as a
function of the signal strength applied to the
left and right channels. As the signal
increases, the number of illuminated
segments will increase and vice-versa.
bt
TRACK SELECT (
/
- )
+
The Track Select function of the TUNE/
SEEK/TRACK buttons are used to quickly
access the beginning of a particular track
when a disc is in play. Each time the Forward
8
TRACK Select (
) side of the button is
+
Download from Www.Somanuals.com. All Manuals Search And Download.
pressed, the next higher track number will
be selected as shown on the display panel.
Similarly, each time the Backward TRACK
track will continue to repeat until the button
is pressed again and the RPT indication
disappears from the display panel. Repeat
- ) side of the button is pressed,
Play mode will also be canceled by activating
Select (
the next lower track number will be selected
as shown on the display panel.
the Track Scan
functions.
cm
or Random Play
co
bu
CUE/REVIEW FUNCTIONS
co
RANDOM PLAY SELECTOR (RND)
-
(
/
)
During disc play, press this button to play the
tracks on the disc in a random shuffled order
(RND will appear on the display panel). In
Random Play mode, the TRACK Select function
will also select tracks in the random order instead
of the normal progression. The Random Play
mode can be canceled by pressing the button
again (RND indication will disappear from the
-) button to advance rapidly
+
High-speed audible search to any section
of the disc can be made by the Cue and
Review functions. Press and hold the Cue
(
) button to advance rapidly in the
+
forward direction (the advancing disc playing
time will be shown on the display panel),or
the Review (
in the backward direction (the decreasing
disc playing time will be shown on the
display panel). During either function, the
elapsed time within each track will
automatically be shown on the display panel.
cn
cp
or Track Scan
display panel) or by camctivating the Repeat Play
functions.
DISC SELECT UP/DOWN
(D.UP/D.DN)
These buttons are used to select the desired
disc for play during changer operation. To ad-
vance to a higher number disc, press the D.UP
button, and to return to a lower number disc,
press the D.DN button. The number of the disc
in play will be shown on the display panel.
cl
TRACK ONE POSITION (TOP)
The Track One Position function is used to
quickly return to the beginning of the current CD
in play (Track 1).
cm
TRACK SCAN SELECTOR (SCN)
cq
DISC EJECT
During disc play, press this button to play the
first 10 seconds of each track on the disc
(SCAN) will appear on the display panel).
When a desired track is reached, press the
SCN button again to cancel the function
(SCAN will disappear from the display panel)
and play of the selected track will continue.
Scan mode will also be canceled by activating
the Repeat Play cn, or Random Play co
functions.
Disc play is stopped and the disc is ejected
when the EJECT button is pressed. It is
necessary to first open the panel before
ejecting the disc. RadioorCDchangeroperation
will automatically resume depending on which
mode was in operation prior to disc play. If
the disc is not removed from the unit within 15
seconds of being ejected, it will automatically
be re-loaded into the unit to prevent it from
being accidentally damaged (
appear on the display panel to indicate that
a disc is loaded in the player). Play of the
IN will
cn
REPEAT PLAY SELECTOR (RPT)
9
During disc play, press this button to repeat
the play of the selected track (RPT will
appear on the display panel). Play of the
button
disc cabnrbe resumed by using the MODE
to choose theCD player function.
Download from Www.Somanuals.com. All Manuals Search And Download.
cr
TIME/FREQUENCY SELECTOR (T/F)
During radio operation, press this button to
dl
FRONT PANEL OPEN/CLOSE
BUTTON
call the time display on the incorporated This button is used to open (fold down) and
quartz clock. The current time will appear close the motorized front panel. To detach
together with an AM or PM indication. The the front panel, press the button so that the
display will return to the radio frequency panel folds down to the lowered position.
indication after 5 seconds.
Grasp the release latch on the middle
underside of the panel and pull the panel
straight off of the panel mounting plate. The
mounting plate will then automatically return
to the upright position within 3 seconds, and
the theft-deterrent LED will begin to flash.
During CD player or changer operation, the
first press of the button will call the time
display. In either case, the display will return
to the disc track indication after 5 seconds.
cs
EQUALIZER BUTTON (EQ)
The EQ button applies preset sound effects
to the unit’s audio output signal. The EQ
button, when pressed, will activate one of
three operating modes (ROCK, CLAS, or
POP). When the EQ function is active, as
displayed on the panel, the bass and treble
levels cannot be changed. When the EQ
function is not active, the unit returns to the
user set bass and treble levels.
NOTES ON USE OF FRONT PANEL:
1. The front panel must be reinstalled with
the mounting plate in the upright position.
To accomplish this, first engage the left
side of the panel into the mounting plate
guide; then carefully press the right side of
the panel until it snaps into place in the
right mounting plate guide.
2.To verify correct panel installation, press the
OPEN/CLOSE button to swing the panel
assembly down, and then up into position
until it locks easily into place. If any
resistance is encountered, re-check panel
orientation in chassis mounting plate.
ct
THEFT-DETERRENT LED
Located on the chassis behind the front
panel, a light-emitting diode (LED) will flash
when the panel is physically removed. The
flashing light serves as a visual warning to
the would-be thief that the unit has been
disabled by removal of the front panel.
3.When taking the front panel with you,
please use the supplied carrying case to
protect the panel from dirt and damage.
Make sure there is no dust or dirt on the
electrical terminals on the back of the
panel as this could cause intermittent
operation or other malfunctions.
cu
RESET BUTTON
The RESET button is located to the right of
the theft deterrent LED. The reset circuitry
should only be activated under the following
and pre-set memories:
1.Upon initial installation after all wiring is
completed.
circumstances as it will erase the time dm
REMOTE SENSOR
The sensor to detect the infrared signal from
the wireless remote control is located
2.If there is a malfunction of any of the adjacent to the lower left corner of the front
10
switches on the unit, pressing the RESET
button may clear the system and return
to normal operation.
panel. For optimum operation of the remote
control, always aim the control at this area.
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC SLOT
MOTORIZED FOLD-DOWN
FRONT PANEL
FRONT PANEL
RELEASE TAB
THEFT-DETERRENT
LED AND RESET BUTTON
(BEHIND FRONT PANEL)
SETTING THE CLOCK
1. Switch the vehicle ignition and radio “on”.
2. Press the Time/Frequency (T/F) button to call the time display.
-
3. While holding the T/F button in, press the Down TUNE/SEEK/TRACK (
) button
to adjust the hours and AM/PM indication, or the Up TUNE/SEEK/TRACK (
)
+
button to adjust the minutes to the correct time.
4. Five seconds after the last hour or minute adjustment is made, the time will be set in
the unit and the display will return to the normal indication.
CD PLAYER ERROR CODES
If a problem should develop while operating the CD player, an error code (ER-1, ER-2,
ER-3, etc.) may appear on the display panel. This can indicate a number of problems
with the unit, including a mechanical error or an error in the microprocessor control of the
player. If an error code should appear, try ejecting and re-loading the disc into the player.
While the disc is out of the unit, make sure it is clean, undamaged, and loaded correctly
(label surface up). You may also try activating the RESET button cuon the unit, but this
will also erase the time and pre-set memories.
If the suggested measures do not solve the problem, contact an approved warranty
station near you for further assistance.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Size:
7" W
x 2" H x 6-5/16" D
178 mm x 50 mm x 160 mm
Operating Voltage:
Fuse Ratings:
12 volts DC, negative ground
Constant (Yellow wire): 15 AMP.
Switched (Red wire): 0.5 AMP.
Output Power:
Output Wiring:
160 watts maximum
(40 watts x 4 channels)
Floating-ground type designed for 4 speaker use.
Front and rear channels CANNOT be combined
(bridged) for use with 2 speakers.
RCA low-level outputs (front and rear channels).
Output Impedance:
Low-Level Output:
Tuning Range:
Compatible with 4 – 8 ohm speakers.
500 mv.
AM: 530 – 1,720 kHz. (10 kHz. step)
FM: 87.5 – 107.9 MHz. (200 kHz. step)
Sensitivity:
AM: 20 uv.
FM: 1.5 uv.
FM Stereo Separation:
CD Frequency Response:
CD Signal/Noise Ratio:
CD Channel Separation:
CD Distortion:
>20 dB
17 – 20 kHz. +0/-3 dB
>65 dB
>60 dB
0.2%
*Specifications are subject to change without notice.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CD CHANGER CONTROLS
next higher track number will be selected
as shown on the display panel. Similarly,
Built into this radio are controls to operate
an optional CD changer. Please check with
your Rampage/Audiovox car stereo
specialist or call 1-800-645-4994 for
recommendations of the models that will
work with this radio.
-
)
each time the Backward Track Select (
button is pressed, the next lower track
number will be selected as shown on the
display panel.
dq
CUE/REVIEW FUNCTIONS
Adjustment of the audio functions (volume,
tone, balance, and fader) for the CD changer
operate in the same manner as they do for
radio play. The following controls will operate
the CD changer when it is installed and
connected to this radio. Refer to the owner’s
manual included with the CD changer for
instructions on the installation and correct
loading and use of the CD magazine.
-
(
+
/
)
High-speed audible search to any section of
the disc can be made by the Cue and Review
functions. Repeated press the Cue (
)
+
side of the button to advance rapidly in the
forward direction (disc play symbol rotation
on the display panel will stop) or the Review
(
- ) side of the button to advance rapidly
in the backward direction.
dn
CD CHANGER MODE SELECTOR
(MODE)
dr
TRACK/DISC SCAN SELECTOR
(SCN)
During radio or CD play, press this button to
select operation of the CD changer as shown
by CDC on the display panel. Disc play will
begin and the DISC and track number will
be shown on the display panel. When the
magazine is loaded into the changer, play
will begin from the first track of the first disc
in the magazine.
When the SCN button is pressed, the SCAN
indication will appear on the display panel,
and the first 10 seconds of each track on
the disc will be played in order. When a
desired track is reached, press the SCN
button twice and play of the selected track
will continue (SCAN will disappear from the
display panel). The Track Scan mode will
also be canceled by activating the Repeat
or Random Play function.
When the Scan button is pressed twice
the DISC and SCN indications will appear
on the display panel and the first 10 seconds
of the first track on each disc in the magazine
will be played. When a desired disc track is
reached, press the SCN button again and
play of the selected disc will continue (DISC
and SCAN will disappear from the display
panel). The Disc Scan mode will also be
do
DISC SELECT (D.UP/D.DN)
These buttons are used to select the desired
disc for play. To advance to a higher number
disc, press the D.UP button. To return to a
lower number disc, press the D.DN button.
The number of the disc in play will be shown
on the display panel.
dp
TRACK SELECT (
/
-)
+
The Track Select functions are used to
quickly access the beginning of a particular
track. Each time the Forward Track Select
13
(
) side of the button is pressed, the
+
Download from Www.Somanuals.com. All Manuals Search And Download.
indication will appear on the display panel
and the tracks on the disc will be played in
a random, shuffled order. The Track Select
button will also select tracks in the shuffled
order instead of the normal progression. The
Random Track mode can be canceled by
pressing the RND button twice or by
activating the Scan or Repeat Play
functions.
When the RND button is pressed twice,
the DISC and RND indications will appear
on the display panel and the discs in the
magazine will be played in a random, shuffled
order, as well as the tracks on each disc.
After playing a track selected at random from
a disc in the magazine, the unit will select
another disc at random and play all the
tracks on it in a random shuffled order. This
will continue from disc-to-disc until the
Random Disc mode is canceled by pressing
the RND button again or by activating the
Scan or Repeat Play functions.
canceled by activating the Repeat or Random
Play function.
ds
DISC/TRACK REPEAT PLAY (RPT)
When the RPT button is pressed, the RPT
indication will appear on the display panel
and play of the selected track will be
continually repeated until the Track Repeat
mode is canceled by pressing the RPT
button twice or by activating the Scan or
Random Play functions.
When the RPT button is pressed twice, the
DISC and RPT indications will appear on
the display panel and play of the selected
disc will be continually repeated until the
Disc Repeat mode is canceled by pressing
the RPT button again or by activating the
Scan or Random Play functions.
dt
DISC/TRACK RANDOM PLAY (RND)
When the RND button is pressed, the RND
CD CHANGER ERROR CODES
If a problem should develop while operating the CD changer, the following error codes may
appear on the display panel.
ER-1: Indicates that there is no magazine loaded in the CD changer.
ER-2: Indicates a problem with the magazine eject function.
ER-3: Indicates an error in the disc loading function.
ER-4: Indicates an error in the disc un-loading function.
ER-5: Indicates an error in the magazine position.
ER-6: Indicates an error in the laser pick-up position.
ER-7: Indicates an error in the laser focus on the disc.
In any of the above situations, try ejecting the CD magazine from the changer and make
sure the discs are clean, undamaged, and loaded correctly (refer to the Owner’s Manual
try activating the RESET button
memories.
of the CD changer). Re-load thecmuagazine and check for proper operation. You may also
on the unit, but this will also erase the time and pre-set
14
If the suggested measures do not solve the problem, contact an approved warranty station
near you for further assistance.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
7
8
9
bl
bm
WIRELESS REMOTE
CONTROL OPERATION
- See Main Unit
RADIO PRE-SETbMoEMORY 1-6
DISC UP SELEcCpT (DISC +)
.
The wireless remote control supplied with
this model is capable of operating most of
the features of the unit from a remote loca-
tion. Each button on the remote control func-
tions in the same way as the referenced
button on the main unit. For optimal opera-
tion of the remote control, always aim it to-
ward the Remote Sensor dmon the front panel
of the main unit.
- See Main Unit
.
DISC DOWN SELECT (DISC -)
- See Main Unit cp.
TRACK/DISC REPEAT (RPT)
- See Main Unit cnand ds.
- See Main Unit
co
and
TRACK/DISC RANDOMd(tRND)
.
1
2
PWR ON/OFF ( ) – See Main Unit
1
TRACK/DISCTRACKONEPOSITION
(TOP) - See Main Unit cl.
VOLUME (LEVEL) CONTROL – See
Main Unit and
2
,
3
,
4
,
5
,
6
7
except press VOL to increase level,
and press VOL to decrease level.
1
15
13
2
3
3
4
5
Unit
3
,
SELECT4BUTTON (SEL) - See Main
,
5
,
6
and
7
.
4
5
AM/FM BAND SELECTOR (BND) - See
Main Unit
9
.
12
11
MANUAL UP/DOWN TUNE – See
Main Unit
increase frequency, press
decrease frequency.
bl
except press
to
to
AUTOMATIC SEEK TUNING – See
6
Main Unit
bl
except press
to Seek
14
upward, press
to Seek downward.
CbtD TRACK SELECT – See Main Unit
and
higher track number, press
select a lower track number.
dp
except press
to select a
9
7
- to
10
bu
and
CD CdUqE/REVIEW – See Main Unit
except press
for Cue
for Review
15
function, and press
function.
16
8
Download from Www.Somanuals.com. All Manuals Search And Download.
bn
bo
bp
TRACK/DcISmC SCAN (SCN) - See
br
MODE SELECTOdRn(MODE) - See
AUDIO EQcUsALIZATION (EQ) - See
and dr.
bq
br
INFRARED SENDER - Emits infrared
the sensor
Main Unit
signal to raddmio which is detected by
.
Main Unit
and
.
BATTERY COMPARTMENT - Holds
one 3.0V dc coin-cell type battery
(CR2025) for remote wireless control
operation.
Main Unit
.
CAREANDMAINTENANCE
Theradiosectionof your new sound systemdoesnot requireanymaintenance. We
recommendyoukeepthismanualforreferenceonthemanyfeaturesfoundinthisunit
as well as how to set the clock.
The compact disc player section also requires no routine maintenance, but proper
understanding of its use and handling will help you obtain maximum enjoyment of its
capabilities. The following points should be observed:
lWhen cleaning the interior of the vehicle, do not get water or cleaning fluids on the
unit.
lTheCDplayerisaprecisioninstrumentandwillnotoperateproperlyinextremehot
orcold. Incaseofsuchconditions, waituntiltheinteriortemperatureofthevehicle
reaches a normal temperature before using the player.
lIfthetemperatureinsidetheplayergetstoohot,aprotectivecircuitwillautomatically
stopplayofthedisc. Inthiscase,allowtheunittocooloffbeforeoperatingtheplayer
again.
lNever insert anything other than a 5" (12 cm) compact disc into the player as the
mechanism can be damaged by foreign objects.
lDo not attempt to use 3" (8 cm) CD-Single discs in this unit, either with or without
an adaptor, as damage to the player and/or disc may occur. Such damage will not
be covered by the Warranty on this product.
lWhen not using the disc player, always remove the compact disc.
lWhen the vehicle warms up during the cold weather or under damp conditions,
moisturemaycondenseonthelensofthediscplayer. Shouldthisoccur,theplayer
will not operate properly until the moisture has evaporated.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
lThe unit is designed with a vibration dampening CD mechanism to minimize
interruptionofdiscplayduetonormalvibrationinamovingvehicle. Whendrivingon
veryroughroads,however,occasionalsoundskipsmayoccur. Thiswillnotscratch
or damage the disc and normal play will resume when the rough conditions cease.
HANDLING COMPACT DISCS
Dirt, dust, scratches, andwarpagecancauseskipsintheplaybackanddeterioration
of sound quality. Please follow these guidelines to take care of your compact discs:
lUse only compact discs with the mark:
lFingerprints, dust, and dirt should be carefully wiped off the disc’s playing surface
(shinyside)withasoftcloth. Wipeinastraightmotionfromtheinsidetotheoutside
of the disc.
lNeverusechemicalssuchasrecordsprays,householdcleanersor thinner to clean
compact discs. Such chemicals can irreparably damage the disc’s surface.
lDiscs should be kept in their storage cases when not in use.
lDo not expose discs to direct sunlight, high temperatures or high humidity for
extendedperiods.
lDo not stick paper, tape, or labels on the disc surfaces nor write on them with any
type of marker.
CD-R PLAYBACK CAPABILITY
This model can play most CD-R media that contains audio programs.
Playback of CD-R depends on the conditions of the recording equipment and the
CD-R disc quality. In some cases, a CD-R disc cannot be played on this unit.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
12 MONTH LIMITED WARRANTY
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of
this product that should this product or any part thereof, under normal use and conditions,
be proven defective in material or workmanship within 12 months from the date of original
purchase, such defect(s) will be repaired or replaced with new or reconditioned product
(at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be
delivered with proof of warranty coverage (e.g. dated bill of sale), specification of
defect(s), transportation prepaid, to the warranty center at the address shown below.
This Warranty does not extend to the elimination of car static or motor noise, to correction
of antenna problems, to costs incurred for installation, removal, or reinstallation of the
product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical
systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial
number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS
WARRANTYISLIMITEDTOTHEREPAIRORREPLACEMENTPROVIDEDABOVEAND,
INNOEVENT,SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE
PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES,INCLUDINGANYIMPLIEDWARRANTYOFMERCHANTABILITY,SHALL
BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR
BREACHOFANYWARRANTYHEREUNDERINCLUDINGANYIMPLIEDWARRANTYOF
MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM
DATEOFORIGINALPURCHASE. INNOCASESHALLTHECOMPANYBELIABLEFOR
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY
OTHERWARRANTY,EXPRESSORIMPLIED,WHATSOEVER. Nopersonorrepresentative
is authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damage so the above limitations
or exclusions may not apply to you. This Warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
U.S.A.: AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NY 11788 l1-800-645-4994
CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA
128-4270E
18
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2001 Audiovox Electronics Corp. l Hauppauge, NY 11788
Printed in China
128-6018
Download from Www.Somanuals.com. All Manuals Search And Download.
|