Patch Release Note
Patch 54266-02
For AR440S and AR441S ADSL Routers
Introduction
This patch release note lists the issues addressed and enhancements made in
patch 54266-02 for Software Release 2.6.6 on existing models of AR440S and
Table 1: Patch file details for Patch 54266-02.
54-266.rez
Base Software Release File
Patch Release Date
9-Dec-2004
54266-02.paz
246872 bytes
Compressed Patch File Name
Compressed Patch File Size
This release note should be read in conjunction with the following documents:
■
■
■
documentation/documentation.html.
WARNING: Using a patch for a different model or software release may cause
unpredictable results, including disruption to the network. Information in this
release note is subject to change without notice and does not represent a
commitment on the part of Allied Telesyn International. While every effort has
been made to ensure that the information contained within this document and
the features and changes described are accurate, Allied Telesyn International
can not accept any type of liability for errors in, or omissions arising from the
use of this information.
Simply connecting the world
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
3
PCR: 40419
Module: OSPF, IPG
Level: 2
If OSPF was configured using the command set ospf dyninterface=stub, to
advertise dynamic interfaces such as PPPoE interfaces as stub links, the
links were not being advertised as expected. This issue has been resolved.
PCR: 40442
Module: IPSEC
Level: 2
When an IPSEC policy is used on a PPP link with iprequest=on, when the
PPP link goes down and IPSEC has traffic to transmit, IPSEC repeatedly
attempts to activate the PPP link again. The frequency of the reactivation
attempts has been reduced.
PCR: 40446
Module: DHCP
Level: 2
In certain situations, if a DHCP client used a DHCP relay agent to request
IP addresses from the router acting as the DHCP server on a different
subnet, it was not be able to renew the IP address allocated to it. This issue
has been resolved.
PCR: 40450
Module: IPG
Level: 2
IGMP entries were sometimes changed to static entries rather than being
deleted when IGMP leaves were received. This issue has been resolved.
PCR: 40451
Module: FIREWALL
Level: 2
The "number of hits" counter in firewall's application rules was not
incremented correctly. This issue has been resolved.
PCR: 40453
Module: PIM
Level: 2
Particular IP packets (unicast destination IP, but multicast destination MAC)
could result in a memory leak, which in some cases could cause the device to
stop responding to the command line. This issue has been resolved.
PCR: 40456
Module: IPG
Level: 2
The enable switch learning command would fail if 802.1X port
authentication was enabled on any of the switch ports. This issue has been
resolved.
PCR: 40458
Module: IPG
Level: 2
The router was accepting network RIP packets from foreign subnets. This
issue has been resolved.
PCR: 40465
Module: PIM6, PIM4
Level: 2
The router could reboot when a user changed the Rendezvous Point
Candidate (RPC) priority in the PIM6 module. This issue has been resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Features in 54266-02
Patch Release Note
PCR: 40466
Module: ISAKMP
Level: 2
When the router was the initiator in an ISAKMP Quick mode exchange with
a PC running Windows 2000 or Windows XP, the IPSEC communication
would not establish successfully. This was because the Windows PC set the
commit bit in the exchange, but sent the CONNECTED Notify payload in
the Quick mode exchange. However, the router was waiting for an
Informational Exchange containing a Notify payload (with the
CONNECTED Notify Message) as specified by RFC 2408. Because an
Informational message was expected, the device did not process the Quick
mode CONNECTED message, and so the exchange was never committed.
Although this behaviour is described as "not required by the IKE standard"
cg0602.mspx], the device will now process CONNECTED messages
received in Quick mode exchanges, to allow interoperability with other
vendors.
PCR: 40470
Module: BGP
Level: 2
When BGP redistributed routes, locally imported routes were selected
rather than peer learnt routes. This issue has been resolved.
PCR: 40479
Module: OSPF
Level: 2
For OSPF-originated routes, it was possible for a route to be deleted from
the IP routing table, but still be referenced by OSPF. This could cause a
router reboot when later generating a summary LSA that contained the old
route. This occurred using the reset ip command. This issue has been
resolved.
PCR: 40496
Module: DHCP
Level: 2
When DHCP is enabled, it reclaims IP addresses at router startup to
determine if the addresses are in use or not. If, during this process, DHCP
was disabled then re-enabled, the router would not attempt to reclaim the
remaining IP address ranges. This would lead to the rejection of DHCP
requests for IP addresses that were still being reclaimed. This issue has been
resolved.
PCR: 40516
Module: DHCP
Level: 2
While initialising a range, the router acting as a DHCP server may release a
dynamic entry incorrectly. This issue has been resolved.
PCR: 40520
Module: DVMRP
Level: 2
Multicast data could not flow from PIM to DVMRP on a PIM/DVMRP
border router. This issue has been resolved.
PCR: 40530
Module: IPG
Level: 2
When both Load Balancer and Firewall were configured, the very first TCP
session was established after rebooting. Subsequent TCP session startup
packets may have been routed out to an incorrect interface causing sessions
to not be established. This issue has been resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
5
PCR: 40537
Module: BGP
Level: 2
When the status of an interface changed, the BGP revaluation of IP routes
for redistribution (via the add bgp import or add bgp network commands)
was incorrect. This gave inconsistent BGP route tables depending on the
order of events. This issue has been resolved.
PCR: 40549
Module: SWI
Level: 2
The receipt of two IP packets whose destination IP addresses were subnet
addresses caused the router to reboot. This issue has been resolved.
PCR: 40560
Module: DHCP
Level: 2
A router reboot could occur when the DHCP server checked whether an IP
address was being used by other hosts, for example, after processing a
DHCP Discover message. This issue occurred if probe=arp was specified
for the DHCP range, and if DHCP had been disabled and then enabled. This
issue has now been resolved.
PCR: 40573
Module: LOG
Level: 2
If the log module was configured to store a very large number of messages
(for example, more than 3000 messages), a watchdog timeout could occur
when the show debug command was executed. This issue has been
resolved.
PCR: 40587
Module: IPG, PIM, DVMRP
Level: 2
When doing Layer 3 IP multicast routing, the router would flood traffic to
all ports in the downstream VLAN. This issue has been resolved, and now
the router will do the portmap calculation based on IGMP, PIM-SM, PIM-
DM, DVMRP neighbour information, and forward the multicast traffic to
the calculated portmap.
PCR: 40588
Module: PPP, CC
Level: 2
A toplogy change in a network could cause a router to attempt to activate
an ISDN call configured with direction=in when the call was already
activated. In this situation, the call was failing, and the PPP link over the call
would not come open. This issue has now been resolved.
PCR: 40592
Module: BOOTP
Level: 2
If a timed-out ARP entry was renewed by BOOTP, the new entry be created
with no port association. This issue has been resolved.
PCR: 40599
Module: FIREWALL
Level: 2
The add firewall apprule command did not correctly accept the port
parameter, so the port value was set to zero. This issue has been resolved,
and the port value is stored correctly.
PCR: 40612
Module: IPG, DNS Relay
Level: 2
There was an issue in DNS Relay that resulted in a memory leak. The leak
occurred when a response to a relayed DNS request contained an
authoritative nameserver or additional information and the DNS request
was forwarded to one of those servers. There was also an issue whereby
DNS queries handled by DNS Relay would sometime result is corrupt
entries in the DNS cache. These issues have been resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Features in 54266-02
Patch Release Note
PCR: 40621
Module: PING
Level: 2
In previous releases, ping poll commands only required entry of the first
three characters of the Source IP Address (sipaddress) parameter. For
example, add ping poll=1 ip=192.168.2.10 sip=192.168.2.1. Subsequent
releases required entry of the first four parameters. This issue has been
resolved, so that it is once again possible to enter just the first three
characters.
PCR: 40646
Module: OSPF, IPG
Level: 2
For both RIP and OSPF, the router was adding a route with it own IP
address for NEXTHOP address. This issue has been resolved.
PCR: 40658
Module: L2TP
Level: 2
L2TP did not handle a change to its peer's UDP source port. If the tunnel
went through a NAT box and that NAT box was reset, then it was possible
for the remote port to change. L2TP should be able to handle this case and
update the tunnel accordingly. A similar problem occurs when a IPsec
NAT-T session (in transport mode) is re-negotiated. IPsec NAT-T uses port
translation to distinguish between multiple clients behind a NAT box. If the
IPsec session is renegotiated then the translated source port that IPsec
passes to L2TP will change. L2TP must be able to handle this case, if it
doesn't then the session will be lost. This issue has been resolved.
PCR: 40668
Module: FFILE
Level: 2
The router would not respond to the setting of the maxqueueseverity
parameter when configuring logging. This issue has been resolved.
PCR: 40728
Module: IPNAT
Level: 2
When IP NAT was configured, a router reboot could occur if a TCP RST
packet was received in which the ACK flag and at least one other flag had
been set. This issue has been resolved.
Level 3
PCR: 31225
Module: IPG
Level: 3
While the router was set with a CIDR interface address, when it received an
ECHO request with a network broadcast destination address for a class C
network, the router sent the ECHO reply packet. Also, the router forwarded
the ECHO request packet using a broadcast MAC address. These issues
have been resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
7
PCR: 40417
Module: OSPF
Level: 3
When LS Acks (Link State Advert acks) were received, they were compared
against the transmitted LSA (Link State Advert). If it was the same, the LSA
was removed from the re-transmission list. The algorithm used in this check
has been changed to be compliant with the algorithm specified in section
13.1 of RFC2328, to determine if the LS Ack received is the instance as the
LSA.
PCR: 40428
Module: IP, FILTER
Level: 3
If the value specified for the sport or dport parameter in the add ip filter or
set ip filter commands was 65535, then the IP filter process would
incorrectly interpret that value as meaning “any “ port. This issue has been
resolved so that port 65535 is now used for the IP filter when specified.
PCR: 40437
Module: CORE
Level: 3
The tick timer was not initialised correctly, which could cause
firewall sessions to time out prematurely when the system time
reached midnight. This issue has been resolved.
PCR: 40493
Module: DHCP
Level: 3
In certain scenarios when acting as a DHCP server, the switch would send
a DHCP ACK to an invalid MAC address. This issue has been resolved.
PCR: 40498
Module: OSPF
Level: 3
When a virtual link end point is no longer reachable, the virtual interface is
not brought down, and the virtual neighbour is not removed. This issue has
been resolved.
PCR: 40513
Module: PIM6
Level: 3
The RP Candidate address was not displayed correctly when issuing the
"show pim6 rps" command. This issue has been resolved.
PCR: 40610
Module: BRIDGE
Level: 3
When the set bridge port command was executed, the bridge configuration
resulting from the create config or show config dynamic=bridge
commands would be incorrect. This issue has been resolved.
PCR: 40676
Module: ADSL, CORE
Level: 3
The ADSL interface, adsl0, did not appear in the Interface Name Summary
table section of the show interface command output or in the
arInterfaceTable in the Allied Telesyn enterprise MIB. This issue has been
resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
8
AR441S ADSL Router Hardware Platform
Patch Release Note
Level 4
PCR: 40441
Module: IPG, VRRP
Level: 4
If VRRP was enabled and a reset ip command was issued followed by a
disable vrrp command, then the device would still reply to pings, even
though the device was no longer the VRRP master. Duplicate echo replies
were seen on the device sending the pings. This issue has been resolved.
Enhancements
PCR: 40521
Module: TACACS+
The new command show tacplus has been added. This command shows the
module status, number of servers, and number of logged in users.
PCR: 40677
Module: ADSL
The new ADSL Annex B firmware has been incorporated to allow
compliance with UR-2 specifications.
AR441S ADSL Router Hardware Platform
Patch 54266-01 includes support for the AR441S ADSL (Annex B) router.
Each AR441S router consists of a base CPU card, enclosure, and power supply.
The base CPU card supports:
■
■
■
One Asymmetric Digital Subscriber Line (ADSL) Annex B port.
Five 10/100 LAN switch ports.
One asynchronous RS-232 (ASYN0) port.
The PIC bay can accommodate any of the following PICs:
•
•
•
•
•
AT-AR020 PRI E1/T1 PIC, one Primary Rate E1/T1 port.
AT-AR021(S) BRI-S/T PIC, one Basic Rate ISDN S/T port.
AT-AR021(U) BRI-U PIC, one Basic Rate ISDN U port.
AT-AR022 ETH PIC, one Ethernet LAN AUI/10BASE-T port.
AT-AR023 SYN PIC, one Synchronous port with universal 50-way
AMPLIMITE connector.
•
•
•
AT-AR024 ASYN4 PIC, four Asynchronous ports with RJ-45
connectors.
AT-AR026 4ETH PIC, four 10BASE-T/100 BASE-TX auto-negotiating
ports with RJ-45 connectors.
AT-AR027 VoIP-FXS PIC, two Foreign Exchange Subscriber (FXS) ports
with RJ-11 connectors.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
9
Main system
Main features of the AR440S routers are:
■
■
■
■
300 MHz RISC processor.
64 MBytes of SDRAM.
16 MBytes of flash memory (1 MByte reserved for boot block code).
5 x 10/100 Mbps full duplex, Layer 2 switched Ethernet LAN ports. All
LAN ports have Auto-MDI, however if Auto-MDI is turned off, then all
ports are hardwired as MDI-X. Software can also force a port to either MDI
or MDI-X. 802.1Q tagged VLANs are supported.
■
■
■
■
1 x ADSL Annex B port
1 x asynchronous DTE port.
Universal AC power supply.
On-board hardware encryption processor for DES, 3DES and AES.
Some encryption options may require feature licenses.
The RS-232 asynchronous serial port (ASYN 0) has a DB9 male connector, is
wired as a DTE port and can be used as a general purpose port for terminals,
printers or modems. The default communications settings are:
•
•
•
•
•
9600 bps
8 data bits
1 stop bit
no parity
hardware flow control
ADSL Interfaces
The ADSL port has an RJ11 connector, and supports Dying Gasp.
Power supply
The routers have a universal AC input connector and a power switch on their
rear panel. The routers require a power input of 100-240 VAC and 50–60Hz.
Some interfaces that may be installed in the router are not transformer isolated.
This means they will be referenced to the frame ground of the equipment and
may be damaged if connected to an interface on another piece of equipment
which is at a different ground potential.
For more information about the hardware, see the AR400 Series Hardware
Reference on the Documentation and Tools CD-ROM.
Features in 54266-01
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Features in 54266-01
Patch Release Note
Table 2: Patch file details for Patch 54266-01.
54-266.rez
Base Software Release File
GUI Resource File Names
d440Se14.rsc (AR440S)
d441Se14.rsc (AR441S)
21-Oct-2004
Patch Release Date
54266-01.paz
Compressed Patch File Name
Compressed Patch File Size
161304 bytes
Patch 54266-01 includes the following enhancements and resolved issues:
PCR: 40563 Module: ADSL
This patch, together with the base software release, supports the AR441S
ADSL (Annex B) router. With this patch, the AR440S ADSL port operates in
Annex A mode for ADSL over POTS, and the AR441S ADSL port operates
in Annex B mode for ADSL over ISDN. (“AR441S ADSL Router Hardware
PCR: 40568
Module: SWK
Level: 3
If the Jabber counter in the output of the show switch port counter
command had more than four digits, it displayed an incorrect value. This
issue has been resolved.
PCR: 40572
Module: M8272
Level: 3
An AR023 synchronous port interface card (PIC) installed in an AR440S
failed the Test facility interface test, even when there was nothing wrong
with the PIC. This issue has been resolved.
PCR: 40576
Module: Firewall
Level: 2
When the firewall was creating new NAT entries under extremely heavy
loads, it occasionally caused a fatal error. This issue has been resolved.
PCR: 40581
Module: BRG
Level: 2
The router could not bridge between an ATM channel and a VLAN
interface. This issue has been resolved.
PCR: 40582
Module: BRG
Level: 2
Occasionally a reboot occurred when the router attempted to bridge traffic
to an ATM channel before the channel had come up for the first time. This
issue has been resolved.
PCR: 40585
Module: IPG
Level: 2
Attaching an IP interface to a VCMux encapsulated ATM interface with
Inverse ARP disabled by using the command:
add ip interface=atm0.1 ipaddress=192.168.1.1
inversearp=off
failed, giving one of the messages:
Error (3005271): Internal Error: Failed to start interface
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
11
Error (3005271): Internal Error: Failed to set interface
This issue has been resolved. It is now possible to add an IP address to a
VCMux encapsulated ATM interface with inversearp set to off. This is
known as RFC 1483 routing. RFC 1577, classical IP and ARP over ATM, still
requires the ATM interface to be LLCSNAP encapsulated.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Features in 54266-01
Patch Release Note
PCR: 40613
Module: SYN
Level: 3
When the Test facility was used to test an AR023 synchronous PIC interface,
it sent some debugging messages, "SYNCheckInterface", to the console port.
This issue has been resolved: the Test facility no longer sends these
messages.
PCR: 40618
Module: Firewall
Level: 3
When NAT was enabled and the router was configured to pass FTP requests
to a server inside the network, the Firewall translated the ftp-data source
port (tcp/20) of an FTP server located on a private interface to another port.
Such packets no longer conformed strictly to RFC 959, and some other
firewalls on the Internet may then have denied them. This issue has been
resolved: the Firewall now sends all ftp-data packets from port 20 on the
firewall, whether or not NAT is enabled.
PCR: 40619
Module: IPG
Level: 2
The output of the show config dynamic command incorrectly displayed
the following parameters for the set ipv6 prefix command, even when they
were not specified with the command:
•
The valid parameter displayed an incorrect value; the router did not
use this incorrect value.
•
The preferred parameter displayed an incorrect value; the router did
not use this incorrect value.
•
•
The onlink parameter displayed the default value yes.
The autonomous parameter displayed the default value on.
This issue has been resolved: the unused parameters are no longer
displayed.
PCR: 40625
Module: SWK
Level: 2
The GUI on the AR441S did not display a port map on the System Status
page. This issue has been resolved. GUI resource file d441Se14.rsc or later
is also required to display the port map on the AR441S.
PCR: 40629
Module: Firewall
Level: 2
A fatal exception in the firewall occurred occasionally when a large number
of proxied connections were rapidly established, for example, during a SYN
attack. This issue has been resolved.
PCR: 40633
Module: ENCO
Level: 2
The encryption engine on the AR441S was not initialised. 3DES outer, 3DES
inner and AES encryption algorithms were not available. This issue has
been resolved.
PCR: 40638
Module: Firewall
Level: 2
When a global interface was dynamically assigned an IP address via DHCP
or PPP, NAT configurations with dynamic private interfaces
(interface=dyn-<dyn-int-name>) were not updated. This resulted in the
failure of sessions received on dynamic private interfaces because the global
IP address was invalid. This issue has been resolved.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Patch 54266-02
13
PCR: 40647
Module: ETH
Level: 2
When a virtual Eth interface was created over ATM, for example, using the
command:
create eth=0 over=atm=0.1
and a VPN configuration was applied directly to that Eth interface, the
router ran out off buffers and caused a fatal exception under heavy
reception load.
This issue has been resolved: a limit has now been set so that the virtual
Ethernet interfaces, like physical Eth interfaces, stop reception by dropping
excess packets when the ethernet receive queue is too long or when the
router is running out of buffers. The ifInDiscards counter, displayed in the
output of the show eth counter command, is incremented when this
happens on a virtual Eth interface.
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Features in 54266-01
Patch Release Note
Patch 54266-02
C613-10417-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
|