USER MANUAL
High Definition Multimedia
Pure Flat Monitor
DM-5952KF / DM-6952KF
A73110002790
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could
result in a frisk of fire or electric shock. Never spill liquid of any kind on
the product.
2. SAFETY INSTRUCTIONS
1. Read all of these instructions.
13. Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage points or other risks. Refer
all servicing to qualified service personnel.
2. Save these instructions for later use.
3. Follow all warnings and instructions marked on the product.
14. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
4. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
5. Do not use this product near water.
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the product.
6. Do not place this product on an unsuitable cart, stand or table; the product
may fall causing damage or injury.
c. If the product has been exposed to rain or water.
7. Slots and openings in the cabinet and the back or bottom are provided for
ventilation. To ensure reliable operation of the product and to protect it
from overheating, these openings must not be blocked or covered.
Placing the product on a bed, sofa, rug, or other similar surface should
never block the openings. This product should never be placed near or
over a radiator or heat register. This product should not be placed in a
built-in installation unless proper ventilation is provided.
d. If the product does not operate normally when the operating
instructions are followed. Adjust only those controls that are covered
by the operating instructions since improper adjustment of other
controls may result in damage and will often require extensive work by
a qualified technician to restore the product to normal operation.
e. If the product has been dropped or the cabinet has been damaged.
8. This product should be operated from the type of power source indicated
on the marking label. If you are not sure what type of power available,
consult your dealer or local Power Company.
f. If the product exhibits a distinct change in performance, indicating a
need for service.
9. This equipment is to be electrically grounded. This product is equipped
with a three-wire plug with a third (grounding) pin. This plug will only fit
into a grounded AC outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact a licensed electrician to replace the
outlet with a properly grounded outlet. Do not defeat the purpose of the
grounding plug!
10. Do not allow anything to rest on the power cord. Do not locate this
product where persons will walk on the cord.
11. If an extension cord is used with this product, make sure that the total of
the ampere ratings on the products plugged into the extension cord does
not exceed the extension cord ampere rating. Make sure that the total of
all products plugged into the wall outlet does not exceed 15 amperes.
2
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USING WITH A LAPTOP
3. README FIRST
If you are using Notebook；Press Fn. + F5 (or Fn. + F3) to output the display
These easy start-up tips will guide you in making the connections to get you
up and running.
to CRT only (CRT output combination key might be different on every
notebook), or press combination key again to show on both CRT and LCD
display.
USING WITH A DESKTOP PC OR LAPTOP
1. Prior to connecting the monitor, if you have a desktop monitor connected to
your PC, please insure that the video card refresh rate is set within the
USING WITH A MAC
1. Plug the AC power cord from the power source (outlet) to the AC input of
Monitors frequency range by going to：
our monitor.
2. Connect the MAC adapter to the MAC monitor output (if required the MAC
model). Refer to the adapter user’s manual for the proper dipswitch settings.
The optimum setting for the monitor is a resolution setting of 800ɰ600 and
Start…Settings…Control
Panel…Display…Settings…Advanced…Adapter.
Set the Adapter refresh rate to 60Hz or “Adapter Default”. This applies to
a refresh rate of 60Hz. Make sure the display settings of the MAC is set to
800ɰ600 at 60Hz as well.
the three supported resolutions of 640×480, 800×600 and 1024×768.
Otherwise, the monitor will not display and the unit will go into
standby mode (Yellow-orange LED).
Note：You need a MAC adapter when using the monitor with older MAC
Computers. The MAC adapter converts the output to VGA HD-15 pin
out. This adapter is available at an additional cost.
2. Plug the AC power cord from the power source (outlet) to the AC input of
the monitor.
3. Connect the VGA cable provided from your computer’s VGA output to the
input on the monitor.
3. Connect the VGA cable from the monitor to the MAC adapter.
VGA 1 VGA 1 input port located in the rear of the monitor.
VGA 2 VGA 2 input port located in the front of the monitor.
Note：Be sure the PC is powered on before the monitor.
Press the VGA1∕VGA2 select button, located next to the front VGA
connector and on the Remote Control until the computer image is
displayed.
SIMULTANEOUS VIEWING OF THE MONITOR AND STANDARD PC
MONITORS
Connect the VGA cable from the PC’s VGA output to the VGA input. Then
plug the desktop monitor’s VGA cable to the monitor VGA output.
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. WITH【CT-1871】VISION CONVERTER
4. WITHOUT VISION CONVERTER
Note：Only for Rev.K-1 or higher.
FIGURE 1：DM-XX52KF W/O VISION CONVERTER CONNECTION
FIGURE 2：DM-XX52KF CONNECT WITH CT-1871 VISION CONVERTER
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. INSTALLATION
6. WITH【CT-1890∕CT-1892】VISION CONVERTER
Precautions
Note：Only for Rev.K-1 or higher.
Monitor shall be placed at least 6 inches away from the obstructer.
a. Monitor will work well when connect with computer and any high
definition receiver. With a high definition resolution, Monitor is designed
without video converter with it. To work as a TV or using with VCR and
DVD, you must to connect with a video converter.
b. The following descriptions are based on Monitor connected with video
converter ready. 【See Figure 2 ~ 3】
Television
1. Install cable from antenna or cable TV to the “F” connector labeled “ANT
IN”.
2. Press the Power ON, and the Red LED Indicator should be lit on the
monitor, and the monitor is on STAND BY mode.
3. Press the POWER button on the Remote-controller; the Red indicator
should turn into green.
4. Press TV∕PC∕AV button or press TV button on Remote-Controller
until the monitor displays MAIN NTSC TV.
5. To switch to TV∕CATV mode, select TV if you are using an antenna, or
select CATV if you have a cable service.
6. Press AUTO button with your remote control, and Monitor will now
preset all active channels into memory.
7. Selecting a channel.
a. Press CH▲∕▼to select channels on Remote control or on the front
panel
.
FIGURE 3：DM-XX52KF CONNECT WITH CT-1890/CT-1892 VISION CONVERTER
b. Press the numeric key to select a desired channel.
8. Press VOL +∕VOL - to adjust the volume on remote control or the front
panel.
Video Recorder (VCR)
1. To connect the signal by F Connector, following the instruction to setup
your Television.
2. If using the Video (Composite) from the VCR, connect the Video input
with Left, and Right Speaker.
3. Start the VCR.
4. Using the Remote control press TV∕PC∕AV button until or press
VIDEO button until VIDEO appears on the screen.
5. If using the S-Video output of the VCR. Connect an S cable from the
VCR to Monitor.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
High Definition Receiver
6. Connect the Left and the Right audio channel to monitor.
7. Start the VCR.
1. If your HD receiver has a VGA connector, it can be used to input monitor.
2. Connect a Receiver to the monitor using the VGA1 located on the rear
panel or VGA2 located on the front panel.
8. Press the TV∕PC∕AV button or press S-VHS button by remote control
until S-VHS appears on the screen.
3. Connect the Audio to appropriate audio connectors next to the VGA
connector.
DVD player
4. Using the Remote control, press the TV∕PC∕AV button or press VGA1
∕VGA2 button until VGA1∕VGA2 appears on the screen.
5. Press MENU, then press the right arrow key on the picture to adjust the
geometry controls for a good picture.
6. If using the component output of the DVD, connect an component video
cable from the DVD with monitor.
7. Connect the left with the right audio channel.
8. Start the DVD player.
9. Using the Remote Control, press the TV ∕ PC ∕ AV button or the
Component button until Y,Cb,Cr∕Y,Pb,Pr appears on the screen.
1. Connect the Video input with Left and Right speaker on DVD.
2. Start the DVD player.
3. Press the TV∕PC∕AV button or press VIDEO button by Remote
control until VIDEO appears on the screen.
4. If using the S-Video output of the DVD, connect an S cable from the
DVD with monitor.
5. Connect the Left with the Right audio channel.
6. Start the DVD player.
7. Press TV∕PC∕AV button or S-VHS button until appears on the screen.
8. If using the component output of the DVD, connect a component video
cable from the DVD with monitor.
9. Connect the left with the right audio channel.
10. Start the DVD player.
11. Using the Remote Control, press the TV ∕ PC ∕ AV button or the
Component button until Y, Cb, Cr∕Y, Pb, Pr appears on the screen.
Computer
1. Connect the computer with the monitor by using VGA1 that located on
the rear panel, or VGA2 that located on the front panel.
2. Connect the Audio to the appropriate audio connector next to the VGA
connector.
3. Press the TV∕PC∕AV button or press VGA1∕VGA2 button until
VGA1 ∕VGA2 appears on the screen.
4. If monitor has no display, check your video card on the appendix B.
5. If there is no display on the screen, verify if the proper input VGA1∕
VGA2 has been manually selected.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
8. USING THE MONITOR
POWER
(Toggle) Starts or stops the monitor function.
DEGAUSS
(PC⁄TV⁄AV)
This is a dual function key:
This section describes how to use and make adjustments to the monitor. It
also provides a reference to the control panel and the remote control.
a. Switch the input source through TV∕PC∕VIDEO∕S-
Video ∕COMPONENT∕TV while connect with a vision
converter.
Using the Control Panel
b. Press this key to execute degaussing while in normal
status. Each degauss is lasting for 4 seconds, and
waiting for 5 minutes to re-do degauss.
Using control panel to control the monitor instead of the remote control.
However, some other functions are not set on control panel. There are 7 panel
keys, and following lists the function buttons on the control panel:
MENU
(Toggle) Enables/Disables the on-screen display menu, or
return to the upper level menu in the menu mode.
SEL＋∕CH＋
SEL－∕CH－
This is a dual function key:
a. Press SEL
＋∕
－
to serve as menu item selection.
b. Press CH＋∕－ to adjust the channel.
DM-XX52KF VGA2 IN & PANEL KEYS
Note：
Indicators
When you are adjusting a function under the magnitude bar, you may also
adjust other items in the same group by pressing the up∕down keys. Don’t
go back to the previous menu by way of the MENU key.
a. Power LED shows power on∕off, and power saving status.
b. Stereo LED is lit when the TV programs being received.
c. SAP LED is lit when the program is broadcast in Sub-audio.(2nd audio
program)
VOL＋∕－
This is a dual function key:
a. Press VOL＋ ∕－to control volume in any mode, except
in menu function.（optional）
Power LED
Green
Stereo LED
Stereo On (Red)
Mono Off
SAP LED
Normal on
Stand by
Main Audio Off
b. Press VOL＋ ∕－to control the selection function while
Amber
Red
Sub Audio On (Yellow)
in menu mode.
Suspend∕Active off
Power off
Select TV or CATV pair as inputs. While in the TV/CATV
mode; the VGA 1∕VGA 2 key serves as TV∕CATV key.
TV∕CATV
Red
(VGA 1∕VGA2)
TABLE 1：INDICATOR OPERATION DESCRIPTION
Note
：
Auto-switch function ： On VGA mode, upon POWER-ON, and at
POWER-ON only, the monitor will automatically switch to the other port
when NO signal appears after 8 seconds. On other words, VGA1 will
switch to VGA2, and vice versa. But if ports have NO input, this monitor
will switch back to the original default port.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note:
9. Using the Remote Control
The mute function will automatically unlock if any adjusts are made related to
audio (i.e., volume, bass, etc.)
Using remote control instead of the control panel is convenient to operate the
monitor. Some of the keys must to work by connect with MATE, and these are
DISP, SLEEP, MTS, JUMP, ADD∕ERASE, AUTO, TV, VIDEO, S-VHS,
COMPONENT, TV∕PC∕AV, TV∕CATA, PIC-STD, PIC∕PAGE, PIC-SEL,
SYSTEM, FINE TUNING, CH-LOCK, FIELD, LANG, CAP∕TXT, CCD.
Following lists the function keys on the remote control:
POWER
Starts or stops the monitor function.
To Start or stop the multiple monitors function in the
meanwhile. In general, this function is used well with
multiple monitors’ control.
POWER ON∕OFF
DISP
Display the current mode on the present status.
SLEEP
To set the sleep timer, each press will increase the sleep
timer in 10-minute intervals up to 120 minutes (then back to
00). When the sleep count reaches the last 5 minutes, the
screen will show up every minute for 3 seconds. During the
last minute, and it will display every 10 seconds.
MTS
Multi-Sound selection.
MUTE
JUMP
Cuts audio and turns audio back on.
Returns to the previous channel.
ADD∕ERASE Allows the user to Add∕Erase channels manually.
AUTO
Automatically scan all the channels by signal responds, and
to set them on the preset mode.
MENU
Enable/Disables the On-Screen Display Menu.
MIC
∕
∕
SEL＋
SEL－
This is a dual function key:
a. Press SEL ＋∕－ to serve as menu item selection.
b. MIC for R mode.
MIC
VOL＋∕－
This is a dual function key:
a. Press VOL ＋ ∕ － to control volume in any mode.
REMOTE CONTROL
（optional）
b. Press VOL＋∕－ to control the selection function while in
menu mode.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SYSTEM
Changes the video system on TV, Video, and S-VHS.
System types are PAL, PAL-M, PAN-N, and SECAM.
Note：Volume control function will effect while connect with Vision Converter.
FINE TUNING
CH-LOCK
FIELD
Allows for fine-tuning of channels.
For Parental Control.
SET
Through DM RS232 V0.9 (Serial Transmission Communication
interface) to remote control the device. To identify the monitor, you
must to set an ID number (ID=1~99) to each of the monitor under
DM RS232 V0.9 Control page.
A FIELD 1 or FIELD 2 toggle. (Useable only when CCD is
on).
ID
To set the ID number to control the monitor from the other.
Select TV source.
LANG
Language Selection (1 or 2).
Accessible only when CCD is on.
Caption control.
TV
CAP∕TXT
CCD
VIDEO
Select VIDEO source.
S-VHS
Select S-VHS source.
Component
Select a Compound signal source:
Y,Pb,Pr —For High definition component inputs.(CT-1890).
Y,Cb,Cr—For Conventional component inputs.( CT-1890∕
CT-1892).
VGA 1
Select VGA 1 source.
Select VGA 2 source.
VGA 2
TV∕PC∕AV
Select TV∕PC∕VIDEO∕S-Video∕COMPONENT∕switch
source.
TV∕CATV
CH+∕CH-
PIC-STD
Select TV∕CATV source.
Steps through the channels.
Factory preset.
Control and select items PIC-SEL button.
User video adjustment screens.
PIC∕PAGE ▲▼
PIC-SEL
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Following lists the function keys on the OSD:
10. ACCESSING THE MAIN MENU
Note:
Access the OSD Menu by control panel on the monitor or the remote control
to make the operation.
ꢀ
ꢀ
ꢀ
ꢀ
Press the Menu button on the control panel or the remote
control to display the main menu.
Press the SEL +/- buttons on the control panel or remote control
to scroll through the menu.
Press the VOL +/-buttons on the control panel or the remote
control to adjust the setting values.
Press Sub-menu to return to upper level while in any sub-menu.
To exit the menu mode, press the menu button while in the top-
level menu.
Screen-1
Screen-4
Screen-7
Screen-2
Screen-5
Screen-8
Screen-3
Screen-6
Screen-9
MAIN MENU
Picture Menu
Fine tunes the Picture image quality manually:
CONTRAST 、 BRIGHTNESS 、 H ∕ V SIZE 、 H ∕ V
POSITION、PINCUSHION、TRAPEZOID、TOP-CORNER、
BOTTOM-CORNER、PIN-BALANCE、PARALLELORGAM、
ROTATION and RECALL.
Note：
a. Recall will replace current settings by the factory-preset values. You can
only recall factory settings when the PC mode is in one of the 14 predefined
modes. See Table 3 appendix B for preset modes. Color recall is used to
call back the factory setting of R.G.B.
b. Above parameters is for PC mode only, and can’t be reached in TV ∕AV
mode. In TV∕AV mode, you can adjust the TV parameters by remote
control.
Color Menu
Select the color temperature to make colors more pure
and vivid. Select user item to adjust the color intensity
by VOL＋∕－key.
Audio Menu
Fine tune the audio functions manually:
OSD FUNCTION CHART
Bass、Treble、Balance、Volume.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Menu
Fine tunes and sets the special functions manually:
g. Moiré
For some modes, it is better to switch the moiré off to get
better video performance, and this option is provided
when Moiré is ON, adjust MOIRE pops out, and adjust
moiré by using ＋∕－key. In TV∕AV mode, moiré can’t
be adjusted.
ID-NUMBER（ 1~99） 、 INSTANT-ON 、 DEGAUSS、
AUTO-SAVING、 AUTO DEGAUSS、 AUTO SHIFT、
OSD BACKGROUND、OSD CONTRAST、AND OSD H
∕V-POSITION、MOIRE、 KEY LOCK、PASSWORD.
h. Key Lock
i. Password
Enable∕Disable the front panel function operation.
a. ID Number
Through DM RS232 V0.9 (Serial Transmission
Communication interface) to remote control the
device. To identify the monitor, you must to set an ID
number (ID=1~99) to each of the monitor under DM
RS232 V0.9 Control page.
To release the disable front panel function operation by
set the password.
j. OSD
Background
Switch the OSD background ON or OFF to adapt to
different software background of the PC.
1. Select the ID number (1~99) by ꢀꢁ tab.
2. After you set the ID, choose high/light to identify the
monitor with has been set with a valid number. The
monitor will correspond with the current status, and this
could control the OSD function directly.
b. Instant-On
Enable∕Disable the INSTANT-ON. Set the INSTANT–
ON YES, the Monitor will start up immediately while the
Power switch on, and the green LED is lit on. The monitor
will stay in the saving mode till the power be turn-on again
while the INSTANT-ON is switch off, and the red LED is lit
on.
c. Auto Saving
e. Degauss
The power will shut down automatically and be in the
power-saving status while the Auto Saving switch on.
Enable∕Disable the AUTO DEGAUSS.
The AUTO DEGAUSS will be executed automatically by
every 24 hours since switch on the function.
f. Auto Shift
Active AUTO SHIFT to protect the screen from result in
the image-remain. The picture will be auto-shift once
every 6 hours.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
11. ENERGY SAVING
12. REAR CONNECTORS【CT-1871】
All monitor is Energy Star compliant. It contains special hardware that
provides energy saving, automatic Stand By and Shut OFF features. After a
period of time, the monitor will be in power-saving status automatically until
the mouse or use the keyboard.
Automatic Stand By and Shut OFF are set through a software program
on your computer.
1. AC in
2. VGA out
Connect the power source to the monitor.
Video signal connector Output the signal to another
monitor.
Composite Video output to another device.
Left speaker signal to another device.
3. Video out
4. Audio out (Left)
5. Audio out (Right) Right speaker signal to another device.
6. Video in
Composite from a VCR or DVD player
Composite, from a VCR or DVD player.
Composite, from a VCR or DVD player.
For S-Video signal.
For S-Video signal.
From a VCR or DVD player.
From Computer or HDTV receiver.
From Computer.
From antenna or cable TV.
Connect the external source from PC to the monitor.
Connect the external source From monitor to other
7. Audio in (Left)
8. Audio in (Right)
9. Audio in (Left)
10. Audio in (Right)
11. S-Video in
12. VGA1 in
13. Audio in
14. Antenna in
15. RS-232 In
Model
MAX. Power on
Stand by
Suspend
Off
DM-6952KF
DM-5952KF
200W
210W
90W
90W
5W
5W
5W
5W
POWER CONSUMPTION STATUS
16. RS-232 Out
external source
.
CT-1871 REAR CONNECTORS
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
14. SIMPLE TROUBLE SHOOTING TIPS
13. REAR CONNECTORS【CT-1890∕CT-1892】
In the rare occasion, you have might problem with your Monivision monitor,
please look at these simple troubleshooting steps to fix the problem.
1. AC in
2. VGA out
Connect the power source to the monitor.
Video signal connector Output the signal to another
monitor.
PROBLEM
LED Not Lit
No Display on monitor
TROUBLESHOOTING
Check your power cord connection.
3. Video out
4. Audio out (Left)
Composite Video output to another device.
Left speaker signal to another device.
5. Audio out (Right) Right speaker signal to another device.
A. PC/MAC：Check the resolution settings of the control
panel display settings in windows to make sure they are
set within the perimeters of our monitors. If you are using
a notebook computer with our monitor you need to
change the configuration of your notebook. The output
needs to be set to CRT.
6. Video in
Composite from a VCR or DVD player
Composite, from a VCR or DVD player.
Composite, from a VCR or DVD player.
For S-Video signal.
For S-Video signal.
From a VCR or DVD player.
From Computer or HDTV receiver.
From Computer.
From antenna or cable TV.
Component Video Input, from a DVD player or HDTV
receiver.
Component Video Input from a DVD player or HDTV
receiver.
7. Audio in (Left)
8. Audio in (Right)
9. Audio in (Left)
10. Audio in (Right)
11. S-Video in
12. VGA1 in
13. Audio in
14. Antenna in
15. Y in
B. Video：Check all of the video connections（RCA, S-
Video）for proper connection.
C. Television ： Make sure the RF cable is connected
properly. Check to see if the monitor is programmed via
our auto programming function. The cable might need to
be set to the proper carrier；STD, HRC or IRC.
D. Notebook：If a notebook PC is used, make sure the
customer uses the control F function to make sure the
external monitor function is being used.
16. Pb∕Cb in
17. Pr∕Cr in
Component Video Input from a DVD player or HDTV
receiver.
LED Red
A. Check frequency and resolution settings.
18. Audio in (Left)
19. Audio in (Right)
20. RS-232 In
For Component Video Signal.
For Component Video Signal.
Connect the external source from PC to the monitor.
Connect the external source From monitor to other
external source.
B. Power down and re-power the monitor. Bypass ★ the
converter box, if there is one and plug the VGA signal
directly into the monitor.
21. RS-232 Out
★BYPASS THE CT CONVERTER BOX TO MAKE SURE
THE PROBLEM IS WITH THE MONITOR.
Display Color Error
Discoloration
Check the pins of the signal cable; Make sure the monitor is
plugged to the PC before the PC is booted up.
When operating the monitor, users may find out that putting
the monitor in different locations or switching directions
may render the screen’s display colors abnormal. It is
caused by the influence of the earth’s magnetic field. After
you push the “DEGAUSS” key, the colors should become
normal again.
Other Problems
If the display becomes abnormal due to an electrostatic
abnormal, turn the power off and wait for five seconds, then
turn the power on again and the monitor should function
normally.
CT-1890/CT-1892 REAR CONNECTORS
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Model：DM-6952KF SPECIFICATIONS
16. Model：DM-5952KF SPECIFICATIONS
CRT Size∕Type
32V Pure flat square screens with 104-degree
magnetic deflection, dynamic focus forming, and
75% transmission.
CRT Size∕Type
27V Pure flat square screens with 108-degree
magnetic deflection, dynamic focus forming, and
53.5% transmission.
Dot Pitch（mm）
0.9mm
Dot Pitch（mm）
0.68mm
Maximum Resolution XGA；1024×768ȞNon-Interlacedȟ
Maximum Resolution XGA；1024×768ȞNon-Interlacedȟ
Horizontal frequency 30 kHz to 52 kHz Auto Synchronous
Horizontal frequency 30 kHz to 52 kHz Auto Synchronous
Vertical frequency
Bandwidth
50－120 Hz
Vertical frequency
Bandwidth
50－120 Hz
65 MHz
65 MHz
Video input signal
VGA input∕output
RS-232 input/output
Sync. input
Analog (0.7 Vp-p)
Video input signal
VGA input∕output
RS-232 input/output
Sync. input
Analog (0.7 Vp-p)
15 PIN D-Sub
15 PIN D-Sub
9 PIN D-Sub (Female/Male)
Separate Sync. TTL Level Positive∕Negative
Composite Sync. TTL Level Positive∕Negative
VGA、SVGA、XGA、VESA.
DTV：480p、720p、1080i (Via VGA Input).
15W×2
9 PIN D-Sub (Female/Male)
Separate Sync. TTL Level Positive∕Negative
Composite Sync. TTL Level Positive∕Negative
VGA、SVGA、XGA、VESA.
DTV：480p、720p、1080i . (Via VGA Input)
15W×2
Compatibility
Compatibility
Speaker & Amplifier
Keys
Speaker & Amplifier
Keys
DEGAUSS（TV∕PC∕AV）、MENU、 SEL∕CH
＋、SEL∕CH－、VOL＋、VOL－、VGA1∕VGA2
（TV∕CATV）.
DEGAUSS（TV∕PC∕AV）、MENU、 SEL∕CH
＋、SEL∕CH－、VOL＋、VOL－、VGA1∕VGA2
（TV∕CATV）.
Connectors
AC IN, VGA IN, VGA OUT, Audio IN（R/L）,
RS232 IN, RS232 OUT.
Connectors
AC IN, VGA IN, VGA OUT, Audio IN（R/L）,
RS232 IN, RS232 OUT.
Power
AC 100V~240V Universal；200 W (Max).
Up to 0.9
Power
AC 100V~240V Universal；210 W (Max).
Up to 0.9
Power Factor
Display area (mm)
Dimension (mm)
Net weight (kg)
Power Factor
Display area (mm)
Dimension (mm)
Net weight (kg)
620×465（Factory Default）
865(W)×680(H)×565(D)
70/78 Kg
520×390（Factory Default）
750(W)×591(H)×504(D)
49.5Kg
Operating
Environment
T：
5 to 40°C
H：30 to 80 % RH
Operating
Environment
T：
5 to 35°C
H：30 to 80 % RH
Storage environment
T： －20 to＋60 °C
H：10 to 90 % RH
Storage environment
T： －20 to＋60 °C
H：10 to 90 % RH
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
18. RS-232 CONNECTOR ASSIGNMENT
17. VGA CONNECTOR ASSIGNMENT
1
5
5
1
6
9
6
10
Input Connector Assignment
11
15
1. -----------------------------------
2. -----------------------------------
3. -----------------------------------
4. -----------------------------------
5. -----------------------------------
6. -----------------------------------
7. -----------------------------------
8. -----------------------------------
9. -----------------------------------
No Connection
TXD
RXD
No Connection
No Connection
No Connection
Ground
No Connection
No Connection
1.
Red
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
---------------------------
2.
Green
3.
Blue
4.
Ground
No Connection
R-Ground
G-Ground
B-Ground
No Connection
Ground
Ground
SDA
5.
5
1
6.
7.
9
6
8.
9.
OUT CONNECTOR ASSIGNMENT
10
11
12
13
14
15
1. -----------------------------------
2. -----------------------------------
3. -----------------------------------
4. -----------------------------------
5. -----------------------------------
6. -----------------------------------
7. -----------------------------------
8. -----------------------------------
9. -----------------------------------
No Connection
RXD
TXD
No Connection
No Connection
No Connection
Ground
No Connection
No Connection
H-sync
V-sync
SCL
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
20. IR REMOTE CONTROLLER CODE
19. FACTORY PRESET AND COMPATIBLE MODE
CODE
KEY
CODE
KEY
Mode Resolution H freq (kHz) V freq (Hz) H polarity V polarity Remarks
000H Display
001H CH-UP
002H CH-DOWN
005H AIR/CATV
006H SYSTEM
007H SLEEP
008H Quick View
00AH AUTO search
017H Number key 7
1
2
640×480
720×400
640×350
800×600
800×600
1024×768
480P
31.469
31.469
31.469
37.879
48.077
48.363
31.469
33.750
45.000
35.150
37.860
59.941
70.087
70.087
60.317
72.188
60.004
60.000
60.000
60.000
56.250
72.810
－
－
－
＋
VGA
VGA
018H Number key 8
019H Number key 9
3
＋
－
VGA
035H PIC STD
4
＋
＋
VESA
VESA
VESA
DTV
036H Fine Tuning UP
037H Fine Tuning DOWN
058H PIC SEL (& Parental control)
059H PIC UP (& Parental control)
05AH PIC DOWN (& Parental control)
05BH Parental control menu
5
＋
＋
6
－
－
7
N/A
N/A
N/A
＋
N/A
N/A
N/A
＋
00CH ADD/ERASER
8
1080I
DTV
00DH PC/TV/AV SW (& Y,Pb,Pr direct
key)
9
720P
DTV
10
11
800×600
640×480
VESA
VESA
00EH POWER on/off
00FH MTS
09CH CCD
09DH CCD CAP/TXT
09EH CCD LANG
09FH CCD FIELD
0A0H Power ON
－
－
010H Number key 0
011H Number key 1
012H Number key 2
013H Number key 3
014H Number key 4
015H Number key 5
016H Number key 6
02CH ID
TABLE 3：FACTORY PRESENT
0A1H Power OFF
034H TV direct key
00BH VIDEO direct key
01AH SVHS direct key
02FH Y, Pb, Pr direct key
VIDEO CONVERTER CODE
CODE
KEY
CODE
KEY
01BH VGA1 direct key
01CH VGA2 direct key
01DH MENU
01FH SEL－
003H VOL＋
004H VOL－
009H MUTE
01EH SEL＋
MONITOR KEY CODE
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Enjoy your new DM RS232 V0.9!
21. DM RS232 QUICK INSTALLATION
★ The version mow is V0.9 and will
be updated in the future if
necessary.
Before install DM RS232 V0.9 software, you must to follow the steps
below:
1. Make sure the monitors and computer is turned OFF.
2. Connect the Monitor (COM1/COM2 port) with your computer by DM RS232
V0.9 cable.
Starting Setup
Turn ON the monitor, and turn ON the computer.
ꢀBefore you can start Setup, the DM RS232 V0.9 software must be installed
and running on each computer with windows operation system.
Figure A:DM RS232 V0.9 CONTROL PAGE
START YOUR DM RS232 V0.9
ꢀSelect Serial Port
Step 1:
Download the DM RS232 V0.9 driver on ALBATRON Website
e/rs232.zip).
Under DM RS232 V0.9 Control Page, Select COM1 on the Select Serial Port.
Step 2:
Extract Zip file to “RS232” sub-directory.
Note: The select serial will be set on COM1 automatically, and you will be
warning while the COM1 port has been selected by other interface
each time you enter.
Step 3:
Following the on-screen instructions.
ꢀSetting an ID number
Step 4:
Through DM RS232 V0.9 (Serial Transmission Communication interface)
to remote control the device. To identify the monitor, you must to set an ID
number (ID=1~99) to each of the monitor under DM RS232 V0.9 Control
page.
Installation is complete.
Step 5:
Press START and opening up DM RS232 V0.9 page under Program tools
1. Select the ID number (1~99) by ꢀꢁ tab.
group.
2. After you set the ID, choose high/light to identify the monitor with has
been set with a valid number. The monitor will correspond with the
current status, and this could control the OSD function directly.
STARTꢁPROGRAMꢁDM RS232 V0.9ꢁDM RS232 V0.9
ꢀSelect Mate Signal
1. Under Select Mate Signal to select a video signal to each monitor.
2. Wait for 2 seconds to switch the signal while change the Video signal.
The system will give you a warning message while an error operation.
ꢀExit the Setting
Select the Exit tab to quit DM RS232 V0.9 Control page.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
STATUS CONTROL
There are 6 control entries under status control, the following statements
are related to each Control function:（See Figure A）
Audio Control:
There are 5 entries under Audio control to fine-tune the Audio Volume, Bass,
Treble, Balance.
While without setting ID, （ ID=NO ） the Power 、 VGA 、 Instant 、 Auto-
Saving、Auto- Degauss、Auto- Shift modes and select mate signal can be
controlled to ALL devices.
1. Select the option button on the Audio frame
2. Move the H scroll bar to adjust the audio quality.
Power
1. In general, select On to start the multi monitors’ functions by DM
RS232 V0.9 control.
2. Select Off and the power will be in the power-saving status
automatically.
Select VGA1/VGA2 tab to switch the signal source.
Enable/Disable the INSTANT-ON.
1. Set the INSTANT–ON YES, the Monitor will start up immediately
while the Power switch on, and the green LED is lit on.
2. The monitor will stay in the saving mode till the power is turn-on
again while the INSTANT-ON is switch off, and the red LED is lit
on.
Bass
Control the sub-woofer volume by adjusts the H scroll bar.
Control the Treble volume by adjusts the H scroll bar.
To adjust volume output balance by adjusts the H scroll bar.
Control the volume by adjusts the H scroll bar.
Treble
Balance
Volume
VGA
Instant
Auto-Saving
Select Yes to shut down the power automatically while the current
mode without signal responds or detecting a over-frequency, and
the system will be in the power-saving status while the Auto Saving
switch on.
Auto-Degauss
Auto-Shift
Enable/Disable the AUTO DEGAUSS.
1. Select Yes and the AUTO DEGAUSS will be executed
automatically by every 24 hours while switch on the function
Active AUTO SHIFT to protect the screen from result in the image-
remain.
1. Select Yes to active Auto Shift, and the picture will be auto-shift
once for every 6 hours.
2. Select No to quit Auto Shift set
Background
Moiré
Switch ON/OFF the OSD background to adapt to different OSD
background.
In general, it is better to switch OFF the moiré to get better video
performance. For some mode, is provided when Moiré is ON, adjust
MOIRE pops out, and adjust moiré by using ＋/－key. In TV/AV
mode, moiré can’t be adjusted.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture Control:
Moire. Degauss Control:
Select Moire. Degauss tab to adjust the H moire / V moire by drag the H scroll
in the scroll bar.
1. Select any label on the picture frame to adjust the picture quality。
2. To adjust the color contrasts by drag the Scroll Bar or input an applicable
value in each textbox on the control page.
3. Press Recall to restore the pre-set picture quality。
Color Control:
1. In the Color frame, select a direct label what you want to adjust to.
2. To adjust the color contrasts by drag the Scroll Bar on the Control page.
3. Press Recall 9300K∕6500K∕5500K/ TV to restore the pre-set the RGB
value of 9300K∕6500K∕5500K/ TV。
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
|