AXIS 215 PTZ/ AXIS 215 PTZ-E
Network Camera
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Table of Contents
Accessing the camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessing from a browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Accessing the camera from the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Video and Audio Streams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Video Stream Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
MPEG-4 protocols and communication methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
AXIS Media Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
How to stream MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Other methods of accessing the video stream . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Accessing the setup tools from a browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Custom Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
User Defined Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
PTZ Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Event Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Event Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Port Status (AXIS 215 PTZ only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
System Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Network - SOCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Network - QoS (Quality of Service) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Network - SMTP (email) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Network - SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Network - UPnP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Network - RTP/MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Network - Bonjour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Ports & Devices - I/O Ports (for AXIS 215 PTZ only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Resetting to Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
I/O terminal connector (for AXIS 215 PTZ only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Connection diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LED indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Checking the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Updating the Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Customer Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
File sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
General performance considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Optimizing your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Frame rates - Motion JPEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Frame rates - MPEG-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Accessing the camera
Accessing the camera
The AXIS 215 PTZ/AXIS 215 PTZ-E can be used with most standard operating systems and supports Microsoft
Internet Explorer 6.x or later, Netscape 7.x or later and Mozilla 1.4 or later.
The AXIS 215 PTZ-E Network Camera does not support audio and does not have I/O ports. All references in this
manual to audio and to the I/O parts pertain to the AXIS 215 PTZ Network Camera only.
Note: To view streaming video in Microsoft Internet Explorer for Windows, you must set your browser to allow the AXIS Media Control (AMC)
to be installed on your computer. The first time an MPEG-4 video stream is accessed, AMC also installs an MPEG-4 decoder for viewing
the video stream. As a license is required for each instance of the decoder, the product administrator may have disabled the installation.
If your workstation restricts the use of additional software components, the camera can be configured to use a Java applet for updating
JPEG images. See the online help for more information.
Accessing from a browser
1. Start a browser (Internet Explorer, Mozilla, Netscape Navigator).
2. Enter the IP address or host name of the AXIS 215 PTZ/AXIS 215
PTZ-E in the Location/ Address field of your browser.
3. Enter the user name and password set by the administrator.
4. A video image is displayed in your browser.
Note:
User functions in the AXIS 215 PTZ/AXIS 215 PTZ-E may have been customized to meet the specific requirements of the application.
Consequently, many of the examples and functions in this section may differ from those displayed in your Live View page.
Setting the Password
1. When accessing the camera for the first time, the
‘Configure Root Password’ dialog will be displayed
on the screen.
2. Enter a password and then re-enter it, to confirm the
spelling. Click OK.
3. Enter the User name: root
Note: The default administrator user name root is
permanent and cannot be deleted or altered.
4. Enter the password as set in step 2 above, and click
5. If required, click Yes to install the AXIS Media Control (AMC). You will need administrator rights on
the computer to do this.
Accessing the camera from the Internet
Once installed, the camera is accessible on your local network (LAN). To access the camera from the Internet you
must configure your router/firewall to allow incoming data traffic. For security reasons this is usually done on a
specific port. Please refer to the documentation for your router/firewall for further instructions.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Accessing the camera
The Live View page
The following provides an overview of each button on the Live View page. If the AXIS 215 PTZ/AXIS 215
PTZ-E has been customized, the buttons will be displayed accordingly:
The Video Format drop-down list allows the video format on the Live View page to be
temporarily changed.
The two types of Output button (AXIS 215 PTZ only) each control the output directly from the Live
View page. These are configured under Setup > Live View Config > Layout.
Active/Inactive - click these buttons to
manually start and stop a connected device,
e.g. switch a light on/off.
Pulse - click this button to activate the
output for a defined period of time, e.g.
to switch on a light for 20 seconds.
These buttons start/stop the Sequence Mode which automatically displays the view from preset
positions at set intervals. Sequence mode is configured in Setup > PTZ Configuration > Sequence
Mode.
The source list is used to select the preset positions already configured in the camera. These
are created in Setup > PTZ Configuration > Preset Positions.
The Manual trigger buttons trigger an action directly from the Live View page. These buttons are
configured under Setup > Live View Config > Layout. Click these buttons to manually start and
stop events.
Use the Snapshot button to capture a snapshot of the image currently being displayed in the
window. Right-click on the image to save it in JPEG format on your computer.
Area Zoom
This allows you to draw a box over a desired area to zoom into. In order to fine-tune the precision, Area zoom
should be calibrated from Setup > PTZ Configuration > Advanced > Calibration.
To activate Area Zoom on the Live View page, click the Center mode button in the AMC viewer toolbar (in
other Internet browsers choose PTZ > Center). Click in the image and while holding down the left mouse
button, draw a square over the area you would like to zoom into.
Pan/Tilt/Zoom controls
The Live View page also displays the Pan/Tilt/Zoom controls. These are enabled/disabled for specified
users by the administrator under System Options > Security > Users > User List.
(PTZ Configuration > Advanced > Limits.)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Accessing the camera
The control panel
Click the Ctrl panel button to display the control panel, where the following settings
are available:
• Auto focus - automatically adjusts the image focus.
• Backlight comp - enabling backlight compensation makes the subject clearer
if the image background is too bright, or if the subject is too dark.
• IR cut filter - when set to off, the camera will be able to “see” infrared light,
e.g. at night, thus making the image clearer. The image is shown in black &
white when the IR cut filter is off.
• Brightness - the image brightness can be adjusted using the +/- buttons,
where a higher value produces a brighter image. Click the Reset button to
revert to the values saved under Video & Image > Advanced > Camera.
• Shortcuts - these buttons can be configured to provide direct access to vari-
ous built-in auxiliary commands provided by the PTZ driver. See Advanced -
Viewer controls
The default viewer to use for displaying moving images is selected from Setup > Live View Config > Layout.
Control, on page 9 for more information. The AMC viewer toolbar displays the following buttons:
The Play/Stop buttons start and stop the live video stream.
The Snapshot button takes a snapshot of the currently displayed image. The Snapshot function and the
target directory for saving snapshots can be configured from AMC (AXIS Media Control), which is
available from the Windows Control Panel (Internet Explorer for Windows only).
Click the Start recording button to make an MPEG-4 recording. Click again to stop the recording. The
recording is saved in the folder specified in the Recording tab in the AMC Control Applet. Only available
if the recording button is enabled on the Live View Config page
Click the View Full Screen button and the video image will fill the entire screen area. No other windows
will be visible. Press Esc (Escape) on the computer keyboard to cancel full screen view.
Click the Mute /Microphone buttons to switch the sound off and on. Only available if Audio is
enabled. (AXIS 215 PTZ-E does not support audio.)
Use the sliders to control the volume on the speaker and microphone. The volume can be set
between 0 and 100. (AXIS 215 PTZ-E does not support audio.)
Navigation mode:
Center will move the camera view to center on the position that was clicked. Also used for Area zoom.
Joystick moves the camera in the direction indicated by a mouse click, relative to the center of the
image. The further from the center the image is clicked, the higher the movement speed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Accessing the camera
Server push (not available for Microsoft Internet Explorer)
With this method, the AXIS 215 PTZ/AXIS 215 PTZ-E maintains and controls an open HTTP connection to the
browser and sends data as and when required, for as long as required.
QuickTime
For use with MPEG-4 only. Note that in the settings for Video & Image > Advanced > MPEG-4, the Video
object type must be set to Simple.
Java applet
This alternative uses a Java applet to update the images in the browser. No download is required. Note that
when this alternative is selected, external video sources will not be available on the live view page, and audio
will be mono-directional only (to the client only). (AXIS 215 PTZ-E does not support audio and does not have
I/O ports.)
Still Image
Displays still images only. Hit your browser’s Refresh button to view a new image.
PTZ Control Queue
Only one user can use the Pan/Tilt/Zoom controls at any one time. When multiple users are accessing the AXIS
215 PTZ/AXIS 215 PTZ-E’s Live View page, they can be placed in the PTZ control queue and assigned a set
period of time during which they have the use of the PTZ controls. Use the buttons to request or release control
of the PTZ controls.
The PTZ Control Queue is set up by the administrator under PTZ Configuration > Control Queue.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Video and Audio Streams
Video and Audio Streams
The AXIS 215 PTZ/AXIS 215 PTZ-E provides several different image and video formats. The type to use depends
on your requirements and on the properties of your network.
The Live View page in the AXIS 215 PTZ/AXIS 215 PTZ-E provides access to Motion JPEG and MPEG-4 video
streams, as well as to single JPEG images. Other applications and clients can also access these video and audio
streams/images directly, without going via the Live View page.
Note: AXIS 215 PTZ-E Network Camera does not support audio.
Video Stream Types
Motion JPEG
This format uses standard JPEG still images in the video stream. These images are then displayed and updated at
a rate sufficient to create a stream that shows constantly updated motion.
The Motion JPEG stream uses considerable amounts of bandwidth, but also provides excellent image quality and
access to each and every individual image contained in the stream.
Note also that multiple clients accessing Motion JPEG streams can use different image settings.
MPEG-4
This is a video compression standard that makes good use of bandwidth, providing high-quality video streams
at less than 1 Mbit/s.
The MPEG-4 standard provides scope for a large range of different coding tools for use by various applications
in different situations, and the AXIS 215 PTZ/AXIS 215 PTZ-E provides certain subsets of these tools. These are
represented as Video object types, which are selected for use with different viewing clients. The supported video
object types are:
• Simple - sets the coding type to H.263, as used by e.g. QuickTime™.
• Advanced Simple - sets the coding type to MPEG-4 Part 2, as used by AMC (AXIS Media Control)
When using MPEG-4 it is also possible to control the bit rate, which in turn allows the amount of bandwidth
usage to be controlled. CBR (constant bit rate) is used to achieve a specific bit rate by varying the quality of the
MPEG-4 stream. When using VBR (variable bit rate), the quality of the video stream is kept as constant as
possible, at the cost of a varying bit rate.
Notes: • MPEG-4 is licensed technology. The AXIS 215 PTZ/AXIS 215 PTZ-E includes one viewing client
license. Installing additional unlicensed copies of the viewing client is prohibited. To purchase addi-
tional licenses, contact your Axis reseller.
• All clients viewing the MPEG-4 stream must use the same image settings.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Video and Audio Streams
MPEG-4 protocols and communication methods
To deliver live streaming video over IP networks, various combinations of transport protocols and broadcast
methods are employed.
• RTP (Realtime Transport Protocol) is a protocol that allows programs to manage the real-time transmission of
multimedia data, via unicast or multicast.
• RTSP (Real Time Streaming Protocol) serves as a control protocol, to negotiate which transport protocol to
use for the stream. RTSP is thus used by a viewing client to start a unicast session, see below.
• UDP (User Datagram Protocol) is a communications protocol that offers limited service for exchanging data
in a network that uses the Internet Protocol (IP). UDP is an alternative to the Transmission Control Protocol
(TCP). The advantage of UDP is that it is not required to deliver all data and may drop network packets when
there is e.g. network congestion. This is suitable for live video, as there is no point in re-transmitting old
information that will not be displayed anyway.
• Unicasting is communication between a single sender and a single receiver over a network. This means that
the video stream goes independently to each user, and each user gets their own stream. A benefit of unicast-
ing is that if one stream fails, it only affects one user.
• Multicast is bandwidth-conserving technology that reduces bandwidth usage by simultaneously delivering a
single stream of information to multiple network users. This technology is used primarily on delimited net-
works (intranets), as each user needs an uninterrupted data flow and should not rely on network routers.
AXIS Media Control
For accessing live video (MPEG-4 and/or Motion JPEG) and audio from AXIS 215 PTZ/AXIS 215 PTZ-E, the
AXIS Media Control (AMC) in Microsoft Internet Explorer for Windows is recommended. This ActiveX
component is automatically installed on first use, after which it can be configured by opening the AMC Control
Panel applet from the Windows Control Panel. Alternatively, right-click the video image in Internet Explorer.
Note: AXIS 215 PTZ-E does not support audio and does not have I/O ports.
How to stream MPEG-4
Deciding on the combination of protocols and methods to use depends on your viewing requirements, and on
the properties of your network. Setting the preferred method(s) is done in the control applet for AMC, which is
found in the Windows Control Panel. When this has been set, AMC will test all the selected methods in the
specified order, until the first functioning one is found.
RTP+RTSP
This method (actually RTP over UDP and RTSP over TCP) should be your first consideration for live video,
especially when it is important to always have an up-to-date video stream, even if some images do get dropped.
This can be configured as multicast or unicast.
Multicasting provides the most efficient usage of bandwidth, especially when there are large numbers of clients
viewing simultaneously. Note however, that a multicast broadcast cannot pass a network router unless the
router is configured to allow this. It is thus not possible to multicast over e.g. the Internet.
Unicasting should be used for video-on-demand broadcasting, so that there is no video traffic on the network
until a client connects and requests the stream. However, as more and more unicast clients connect, the traffic
on the network will increase and may cause congestion. Although there is a maximum of 20 unicast viewers,
note that all multicast users combined count as 1 unicast viewer.
RTP/RTSP
This unicast method is RTP tunneled over RTSP. This can be used to exploit the fact that it is relatively simple to
configure firewalls to allow RTSP traffic.
RTP/RTSP/HTTP
This method can also be used to traverse firewalls. Firewalls are commonly configured to allow the HTTP
protocol, thus allowing RTP to be tunneled.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Video and Audio Streams
Other methods of accessing the video stream
Video/images from the AXIS 215 PTZ/AXIS 215 PTZ-E can also be accessed in the following ways:
• If supported by the client, the AXIS 215 PTZ/AXIS 215 PTZ-E can use Motion JPEG server push to display
video. This option maintains an open HTTP connection to the browser and sends data as and when required,
for as long as required.
tion=CIF
• Windows Media Player. This requires AMC and the MPEG-4 decoder to be installed. The paths that can be
used are listed below, in the order of preference.
• Unicast via RTP: axrtpu://<IP address>/mpeg4/media.amp
• Unicast via RTSP: axrtsp://<IP address>/mpeg4/media.amp
• Multicast: axrtpm://<IP address>/mpeg4/media.amp
Other MPEG-4 clients
Although it may be possible to use other clients to view the MPEG-4 stream, this is not guaranteed by Axis.
For some other clients, e.g. QuickTime™ the Video Object Type must be set to Simple. It may also be necessary to
adjust the advanced MPEG-4 settings.
To access the video stream from e.g. QuickTime™ the following path can be used:
rtsp://<IP address>/mpeg4/media.amp
This path is for all supported methods, and the client will negotiate with the AXIS 215 PTZ/AXIS 215 PTZ-E to
determine exactly which transport protocol to use.
Audio transmission methods (AXIS 215 PTZ only)
The audio stream can be accessed in the Live View page when viewing either Motion JPEG or MPEG.
Using Motion JPEG
The basic transmission method of audio used in conjunction with Motion JPEG video streaming is transmission
over HTTP. The video and audio streams are not synchronized when using Motion JPEG so the streams may be
slightly out of sync. The latency in any stream should be low, but this will depend on the network infrastructure.
Using MPEG-4
When using MPEG-4, audio is streamed using the same protocol as the video stream.
When audio is transmitted using MPEG-4, the Axis product sends synchronization information along with the
streams to the client that is performing the synchronization.
Audio is streamed from the client to the server over HTTP when using Motion JPEG and MPEG-4.
Accessing the Audio Streams (AXIS 215 PTZ only)
In addition to accessing audio in the Live View page using AMC, audio from the Video Server can also be
accessed in the following ways:
The VAPIX® API
You can read about accessing audio for the other protocols through VAPIX, Axis Communications’ powerful
QuickTime/Windows Media Player
It is possible to use QuickTime and Windows Media Player to listen to the audio stream using the same methods
to access video streams.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Setup
The AXIS 215 PTZ/AXIS 215 PTZ-E is configured from the setup tools, which are available from the link in the
web interface. The setup tools can be used by:
• administrators, who have unrestricted access to all the Setup tools
• operators, who have access to the Video & Image, Live View Config and Event Configuration settings.
Accessing the setup tools from a browser
Follow the instructions below:
1. Start the browser and enter the IP address or host name of the AXIS
215 PTZ/AXIS 215 PTZ-E in the location/address field.
2. The Live View page is now displayed. Click Setup to display the
Setup configuration tools.
Setup tools
11
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Video & Image settings
The following descriptions offer examples of the available features in the AXIS 215 PTZ/AXIS 215 PTZ-E. For
details of each setting, please refer to the online help files
.
To optimize the video images to your requirements, modify the following settings under Image Appearance:
• Resolution (including Aspect ratio correction and 4CIF de-interlacing)
• Compression
• Rotate image
• White balance
• Color setting
Notes: All configuration of images and overlays will affect the performance of the AXIS 215 PTZ/AXIS 215 PTZ-E, depending on the usage and
the available bandwidth. Please keep in mind the following when changing the image settings:
•Lower compression improves image quality, but generates larger files
•Color uses more bandwidth than Black & White
•Rotating the image will lower the maximum frame rate
•When using MPEG-4 as the video format, the compression setting will define the minimum compression level. The compression level will
temporarily increase as and when required, i.e. when the bit rate approaches the maximum value as defined in the current profile@level
combination.
•In certain conditions, the white balancing system will not operate effectively. See Video Image Problems, on page 40 for more
information.
You may need to click the Stop and Play buttons on the Live View page before the settings take effect.
Overlay Settings
Use these settings to include an image as an overlay, and/or
the date and time, along with text of your own.
Date & Time
overlay
image
See Overlay Image Settings below for instructions on how
to upload an overlay image to the AXIS 215 PTZ/AXIS 215
PTZ-E.
Text overlays are included on one line at the top or bottom
of the video image. Use text overlays in combination with
OSDI (On-Screen Directional Indicator) on page 31 to aid
the viewer in navigating the camera.
To set up
PTZ coordinates in
text overlay
Use #P #L to show the Preset and OSDI Zone name as text overlay
Video Stream
The video stream time can be set as Unlimited, or a maximum stream time per session in seconds, minutes or
hours can be defined. When the set time has expired, a new stream can be started by refreshing the page in the
Web browser. Note that the maximum video stream time does not apply to clients connecting via multicast.
To avoid bandwidth problems on the network, the frame rate allowed to each viewer can also be limited. Select
either Unlimited or define a maximum frame rate per viewer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
For a preview of the image and overlay settings before saving, click Test. When you are satisfied with the
settings, click Save.
Please use the online help files
for more information.
Overlay Image Settings
An overlay image is an image included in the video image. This might, for example, be your own company logo.
Follow these instructions to upload and use an overlay image:
1. Go to Setup > Video & Image > Overlay Image.
2. To upload the image to the AXIS 215 PTZ/AXIS 215 PTZ-E, click the Browse button and locate it on your
computer or server.
3. Click the Upload button and follow the on-screen instructions.
4. The image is now available in the Use overlay image drop-down list.
5. Click Save.
6. Go to Setup > Video & Image and modify the parameters under Overlay Settings.
Overlay image requirements:
Image Formats
Image Size
•
•
Windows 24-bit BMP (full color)
Windows 4-bit BMP (16 colors)
The height and width of the overlay image in
pixels must be exactly divisible by 4.
There are a number of limitations when using overlay images, such as the size and positioning of images. Please
use the online help
for more information.
Advanced settings
Camera - to optimize the lighting settings according to your requirements, modify the following settings under
Lighting Conditions:
• Brightness - increase the value to brighten the image.
• Sharpness - increase the value to sharpen the image. A higher value will sharpen the image but also
increase the image noise, especially in low lighting.
• IR cut filter - set the IR cut filter to On, Off or Auto. The IR cut filter can also be set to On, Off or Auto
directly from the control panel on the Live View page.
• Backlight compensation - this setting is used to make the subject appear clearer against e.g. a bright
background.
Low Light Behavior
These settings determine how the camera will function in low light conditions. Adjustments made here affect
image quality and are basically a measure of how much noise to allow in images. Please use the online help
for more information on each individual setting.
• Priority
• Exposure control
• Max exposure time
• Max gain
Image Settings
• Auto focus enabled (default setting)- Auto focus can also be set to On/Off directly from the control
panel on the Live View page.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
• Image freeze on PTZ - freeze the image either during pan, tilt, zoom movement or between preset
positions only. Once the camera has reached its position, the current image is shown.
MPEG-4 Settings
The AXIS 215 PTZ/AXIS 215 PTZ-E supports the following
different MPEG-4 profiles and levels:
Profile@Level
Properties
Advanced Simple Profile @ Level 3b
Max bit rate = 1,5 Mbps
ISMA compliant
Advanced Simple Profile @ Level 5
Max Bit rate = 8 Mbit/s
Level 5 is preferred if there is enough bandwidth available,
as the image quality of the video stream will be better than
if level 3 is used. The viewing client must support the profile
used for the video stream otherwise the MPEG-4 stream can
not be viewed.
Note: AXIS Media Control supports all the configuration possibilities
available on this page.
The GOV structure can be set to either I or IP, which describes the type of images included in the video stream,
as well as their internal order. The IP-structure generally sends the differences compared to the previous image
and far fewer complete images, so this method uses much less bandwidth than the I-structure. The I-structure
gives higher frame rates when using a high resolution, but requires more bandwidth.
The GOV length determines the sum total of P-images and I-images in a GOV. Setting the GOV length to a high
value saves considerably on bandwidth. However there may be noticeable decay in the image at high values.
Note: GOV = Group of VOPs
VOP = Video Object Plane
Video Object Plane = image
Bit Rate Control
Limiting the maximum bit rate is a good way of controlling the bandwidth used by the MPEG-4 video stream.
Leaving the Maximum bit rate as unlimited will provide consistently good image quality, but at the expense of
increased bandwith usage whenever there is more activity in the image. Limiting the bit rate to a defined value
will prevent excessive bandwidth usage, but images will be lost when the limit is exceeded.
Note that a maximum bit rate can be used for both variable and constant bit rates.
The bit rate type can be set as Variable Bit Rate (VBR) or Constant Bit Rate (CBR). VBR will adjust the bit rate
according to the images' complexity, thus using a lot of bandwidth for a lot of activity in the image and less for
lower activity in the monitored area.
Note: Depending on the amount of motion, the required bandwidth may increase by 1-15% for each frame.
Video Stream
This parameter can be set to frame rate to increase the frame rate by 30% in 4CIF resolution. If the resolution is
set to a value lower than 4CIF, the parameter should be set to bandwidth.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Audio Settings (AXIS 215 PTZ only)
This section describes how to
configure the basic audio settings
for the AXIS 215 PTZ, e.g. set the
communication mode and adjust
the sound levels in the microphone
and speaker.
Enable Audio
Check the Enable Audio checkbox
to enable the audio functionality.
Audio Channels
There are two mono audio
channels between the AXIS 215
PTZ and other clients, one for
receiving audio and one for
transmitting audio. Each audio
channel can be turned on or off,
which means that there are four
audio mode options that can be
used.
Full-duplex mode means that you can transmit and receive audio (talk and listen) at the same time, without
having to use any of the controls. This is just like having a telephone conversation. The only controls you may
wish to use are the mute buttons to turn off the sound, and the sliders, to adjust the input/output volume levels.
This mode requires that the client PC has a sound card with support for full-duplex audio. If your available
bandwidth is 0.2 Mbit/s or less, it is recommended that you use Half-duplex mode instead.
Half-duplex mode also transmits and receives audio in both directions, but only in one direction at a time. This
means that you must select when to receive or transmit audio using the push-to-talk button. To speak, press and
hold the button (check that the microphone is not muted). When finished speaking, release the button. You will
now be receiving audio from the other end of the connection.
Note that the push-to-talk button is configured from AMC, see AXIS Media Control, on page 9. It is also possible
to configure the Push-to-talk button so that it toggles between speaking and listening modes. Half-Duplex mode
is best if you only have limited bandwidth available.
When you select Simplex - Network Camera speaker only mode, the speaker connected to the AXIS 215 PTZ
will play audio, but no audio will be transmitted from the AXIS 215 PTZ to other web clients. This could be
used, e.g. to provide spoken instructions to a person seen in the network camera. This mode requires you to use
the push to talk button.
Simplex - Network Camera microphone only mode transmits audio from the microphone connected to the
AXIS 215 PTZ to any web clients. It will not receive audio from any other web clients. This can be used in
remote monitoring, web attractions etc., to provide live audio, as well as video, of a monitored situation.
When using half-duplex, the Send the sound from the active client to all other clients option transmits the
audio signal from the client that is talking to all the other clients.
Audio Input
If there are problems with the sound input being too low or high, it is possible to adjust the input gain for the
microphone connected to the AXIS 215 PTZ.
Source - select Microphone for an external microphone or Line for a Line in device, e.g. an audio mixer for
multiple microphones or a microphone with a built-in amplifier.
Input sensitivity - set the sensitivity level of the audio input according to the following:
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
If Microphone is selected - set the Input sensitivity to:
• High if the connected microphone is an ordinary (unamplified) microphone, e.g. a computer mic or
clip-on mic.
• Low if the connected microphone has a built-in line amplifier.
Enable microphone power - microphone power should only be used with an electret microphone without a
battery. This setting should not be enabled when using a dynamic or battery powered microphone.
Input gain - volume control of the audio input. The Input sensitivity levels High and Low are volume settings
made earlier in the audio path (see above).
Note: Low Input sensitivity should never be compensated by a high Input gain, as this may cause unwanted
noise.
Encoding - select the digital audio encoding format to use.
Bit rate - depending on the selected encoding, set the required bit rate (audio quality). The higher the bit rate,
the greater the bandwidth required.
Alarm level - event types in the AXIS 215 PTZ can be set to use this level as a trigger. Each individual event
type can be configured to trigger if the sound level rises above or falls below the set value.
The alarm level can be set in the range 0-100%, where 0% is the most sensitive and 100% the least sensitive.
Audio Output
If the sound from the speaker is too low or high it is possible to adjust the output gain for the connected active
speaker.
When satisfied with the settings, click Save, or click Reset to revert to the previously saved settings.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Advanced Audio Settings (AXIS 215 PTZ only)
The Advanced Audio settings allows you to tune the external microphone connected to the AXIS 215 PTZ to
suit your environment.
Enable speech filter improves the sound quality when the microphone is placed close to the person talking and
can also help reduce background noise. The filter cuts the lowest and the highest frequencies. The bypass
frequency range is approximately 250Hz to 3700Hz (measured at -10dB cut-off break points).
Enable echo cancellation reduces acoustic echoing if sound from the speaker is captured by the microphone.
Noise canceling is a way of reducing the background noise when there is no useful audio present. A typical
application could be that the camera is set up in a noisy environment, and you are only interested in hearing
audio from the AXIS 215 PTZ when someone is speaking close to the microphone.
Noise canceller attenuation - when the incoming sound is louder than the threshold, it will pass without any
changes. When lower than the threshold, the incoming sound will be reduced by a certain attenuation factor.
The threshold level should be set higher than the background noise, but lower than the useful audio.
There is a trade-off between noise canceling and sound quality. In other words, increasing the noise canceller
attenuation deteriorates sound quality. Adjust the threshold and the attenuation to an optimum by listening and
changing the levels.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Live View Config - Live View Layout
These are the tools for determining the layout of the Live View
page. The layout can be set in 3 ways:
• Use Axis look - the layout is unchanged.
• Use custom settings - modify the default page with your own
colors, images etc. Click the Configure button and see the
following page.
• Own Home Page - upload and use your own custom made
page as the default web page. Click the Configure button
and see the following page.
Custom Settings
Upload Own Web Files
Your own web files, background picture, color etc. must first be uploaded to the AXIS 215 PTZ/AXIS 215 PTZ-E
in order to be available for selection. Once uploaded, the files are shown in the drop-down list.
1. Enter the path to the file, e.g. a file located on your workstation or click the Browse button.
2. Select the user level for the uploaded file. Setting the user access level means that you have complete
control over which pages can be viewed by which users.
3. When the path is shown correctly in the text field, click the Upload button.
All uploaded files are shown in the list in the lower section of the page. To remove a file, check the box provided
next to it and then click the Remove button.
Modify the Axis Look
Adjust the settings under Modify the Axis Look, to change the background color, text color, background
picture, banner, banner link, Logo, etc.
• To use your uploaded file, click the Own radio button and select the file from the drop-down list.
• To use an external file located somewhere other than in the AXIS 215 PTZ/AXIS 215 PTZ-E, click the Exter-
nal radio button and enter the URL to the file (applies to background picture, banner and logo).
18
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Show Setup link
Note that unchecking the box for Show setup link will remove the setup link from the
camera’s Home Page. The setup tools will then only be accessible by entering the full setup
address into the address/URL field of a browser, i.e.
Own Home Page
To use a previously uploaded web page as the default page, check the
checkbox, select the page from the drop-down list and click OK.
Note: You can also add live video from the AXIS 215 PTZ/AXIS 215 PTZ-E to your own web site.
User Defined Links
Enter a descriptive name and enter the URL in the provided field. The link
will appear on the Live View page.
User defined CGI links can be used to issue The VAPIX® API requests, e.g.
PTZ commands.
Example:
1. Check Show custom link 1
user defined link
2. Enter a descriptive name, e.g. CAM START.
3. Select the Use as cgi link radio button and enter the cgi link in the field:
4. Check Show custom link 2.
5. Enter a descriptive name, e.g. CAM STOP.
6. Select the Use as cgi link radio button and enter the cgi link in the field:
7. These links will appear in the web interface and can be used to control the PTZ camera.
For more information on the The VAPIX® API, see the Support / Developer pages on the Axis Website at
Action Buttons - these buttons can then be used to manually trigger and stop an event from the Live View page.
The snapshot button allows users to take a snapshot of the video stream and save it on a computer.
Output Buttons (AXIS 215 PTZ only) - these buttons can then be used to manually start and stop an event from
the Live View page, e.g. switch a light on/off:
• The Pulse button activates the port for a defined period
• Active/Inactive displays 2 buttons, one for each action (on/off)
Default Video Format - select default video format from the drop-down list. Check the box to enable video
format selection from the Live View Page.
Default Viewer
19
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
When using Microsoft Internet Explorer (IE) for Windows, select your preferred method of viewing moving
images. The options are:
• AMC (ActiveX) - this is the best choice for fast image updating in Internet Explorer for Windows, but
might not be possible on computers that have restriction on the installation of additional software.
• QuickTime - for use with MPEG-4 only, select this to use the QuickTime plug-in for Microsoft Internet
Explorer.
• Java applet - this alternative uses a Java applet to update the images in the browser.
• Still Image - displays still images only. Hit the Refresh button in your browser to view a new image.
When using any other browser than Internet Explorer for Windows, select the appropriate method from the
drop-down list for viewing images. The available options are similar to Internet Explorer except for Server
Push. With this method, the camera maintains and controls an open HTTP connection to the browser and sends
data as and when required for as long as required.
Please see the online help
for more information.
Viewer settings
Show viewer toolbar - uncheck to remove the viewer toolbar from the Live View page.
Enable MPEG-4 decoder installation - enables/disables the installation of the MPEG-4 decoder included with
AMC.
Show crosshair in PTZ joystick mode - enables/disables a red position indicator in the center of the image
when the joystick navigation mode is selected.
Use PTZ joystick mode as default - enabling this sets the PTZ mode to joystick. The mode can temporarily be
changed on the Live View page, but will default to joystick if selected.
Enable recording button - enables recording directly from the Live View page. The recording is saved in the
folder specified in the Recording tab in the AMC Control Applet. Note that this button is only available when
viewing with AMC.
HTML Examples
You can add live video from the AXIS 215 PTZ/AXIS 215 PTZ-E to your own web site. The camera can transmit
a Motion JPEG stream to up to 20 simultaneous connections, although an administrator can restrict this to
fewer.
Select the preferred Video Format from the drop down list. The available options are Motion JPEG, MPEG-4
using AMC and MPEG-4 using QuickTime. If MPEG-4 is set as the video format, note that a separate MPEG-4
license is required for each viewer.
The Motion JPEG selection has additional settings for Image Type, Image size and other optional settings to
configure the video stream to suit your Web page. Click Update once satisfied.
The camera generates the required source code for your configuration. Copy this code and paste it into your own
Web page code.
External Video
An external video source is a source originating from some other Axis device on the network. The images from
these sources can be displayed just as if they were produced by the AXIS 215 PTZ/AXIS 215 PTZ-E.
The External Video Source list shows all of the external video sources currently configured. The information
displayed is the name of the source and the path to the video stream. Up to 20 external video sources can be
configured. Please see the online help
for more information.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
PTZ Configuration
Preset Positions
A preset position is a pre-defined camera view than can quickly and easily be viewed.
From Preset Position Setup, use the Pan, Tilt and Zoom (PTZ) controls to steer the camera to the required
position. When satisfied with the camera's position, enter a descriptive name. This camera position is then saved
as a preset position.
The AXIS 215 PTZ/AXIS 215 PTZ-E will take the exact position
when the preset's name is selected from the Preset positions
drop-down list. Preset positions can be selected in Live View,
from events and in Sequence mode.
One position can be set as the Home position, which is readily
accessible by clicking on the Home button in both the Preset
Position Setup window and the Live View window. The
position's name will have (H) added, e.g. Office Entrance (H).
Sequence Mode
The Live View page can be configured to rotate through the
selected preset positions, in a set order or randomly.
Select the desired preset positions and enter the time to display each position. Click Save.
The Sequence buttons will appear on the Live View page to enable the viewer to start and stop the
sequence mode.
OSDI Zones
On-Screen Direction Indicator Zones are areas that you define with coordinates and a descriptive name. These
zones can then be included in the Image text to aid the viewer in navigating the camera.
The camera uses the coordinates of the center of the image to set the lower left and upper right zone areas. First
navigate where you would like the most lower left point of the OSDI Zone to be located. The coordinates are set
by clicking on the Get button. Proceed to where the upper right point of the zone should be located and click on
the corresponding Get button. Give the zone a descriptive name and go to Overlay Image Settings, on page 13
for information about including the name of OSDI Zone in the Image text.
Advanced - Limits
Define the pan, tilt and zoom limits for the AXIS 215 PTZ/AXIS 215 PTZ-E. Movements to the left and right, up
and down can be restricted to narrow the area under surveillance.
Note: The image is automatically flipped over (E-flip) e.g. when the target moves under the camera and then
moves on. In situations where E-flip is not desired, set the Lower limit to -90°, which will disable this function.
Move speed - sets the speed of the camera's Pan/Tilt movements. The default setting is maximum speed.
Enable proportional speed - when using a joystick (or emulating one with the mouse), this setting can be used
to reduce the maximum pan/tilt movement speed, i.e. the speed the camera moves at when the joystick is pushed
all the way out in any pan/tilt direction. This is useful when the camera is zoomed in on an object and a pan/tilt
movement is performed
Auto-flip - the AXIS 215 PTZ will simulate continuous pan movement in the same direction, i.e. the camera will
pan the full 360 degrees, even though there is a mechanical stop at ±170 degrees.
This is achieved by reversing the camera lens and flipping it over when the camera reaches the mechanical stop.
There will be a slight delay during the lens reversal.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Setup
Movement prediction after Auto-flip - the camera will attempt to predict the new position in the pan
movement, after compensating for the slight delay while the camera changes direction after an Auto-flip. This is
useful for e.g. tracking moving objects or persons when using the joystick or emulated joystick mode.
See the online help for more information.
Advanced - Ctrl Panel
This allows you to add a shortcut command button to the control panel. This requires you to provide the URL
(path) to an auxiliary command provided by the PTZ driver, or to some other command accessed via the The
VAPIX® API. See the online help for more information.
Advanced - Calibration
The Area zoom functionality on the Live View page provides the possibility to zoom in on an area marked by
drawing a square directly in the image. In order to fine-tune the precision of the square, Area zoom should first
be calibrated from this page.
Follow the on-screen instructions to calibrate the precision of the zoom.
Control Queue
PTZ Control Queue - the administrator can set up a queue for the PTZ controls. Once set up, the PTZ Control
Queue buttons will appear on the Live View page offering one viewer exclusive control for a limited amount of
time. Other users will be placed in the queue.
PTZ Control Queue on Live View page
Please see the online help
for more information.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Event Configuration
Event Configuration
This section describes how to configure the AXIS 215 PTZ/AXIS 215 PTZ-E for alarm and event handling. The
AXIS 215 PTZ/AXIS 215 PTZ-E can be configured to perform certain actions when certain types of events
occur.
Event Type
A set of parameters describing how and when the AXIS 215 PTZ/AXIS 215 PTZ-E is to perform certain actions
Triggered Event page 24
Scheduled Event page 25
Action
the circumstances that start an event
the circumstances that start an event
what occurs when the event triggers
e.g. at a signal from an external device, such as motion detection
e.g. at a pre-programmed time
e.g. uploaded video images to an FTP server, email notification, etc.
Event Servers
Event Servers are used, e.g. for receiving uploaded image files and/or notification messages. To set up Event
server connections in your AXIS 215 PTZ/AXIS 215 PTZ-E, go to Setup > Event Configuration > Event Servers
and enter the required information according to the selected server type.
Server type
FTP Server
Purpose
Required information
• used for uploading saved images
• Descriptive name of your choice
• Network address (host name or IP address)
• Upload path e.g. images/
• Port number
• User name/Password
• Use passive mode if there is a firewall between the PTZ camera and the FTP server
• Use temporary file if your FTP server doesn’t allow an existing file to be overwritten by a
new file with the same name
HTTP Server
TCP Server
• used for notification messages
• used for uploading saved images
• Descriptive name of your choice
• URL
• User Name and Password (to HTTP server)
• Proxy address/Proxy port (if required)
• Proxy User Name and Password (if required)
• used for notification messages
• Descriptive name of your choice
• Network address (host name or IP address)
• Port
For details on each setting, please refer to the online help files
which are available from each web page.
Note: Pre-trigger and Post-trigger buffers will be lost if the connection to the event server fails.
When the setup is complete, the connection can be tested by clicking the Test button (the connection test will
take approximately 10 seconds).
23
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Event Configuration
Event Types
An Event Type is a set of parameters describing how and when the AXIS 215 PTZ/AXIS 215 PTZ-E is to
perform certain actions.
Example: If somebody passes a connected sensor and an event type has been configured to act on this, the camera can e.g. record and save
images to an FTP server, and/or send a notification email to a pre-configured email address with a pre-configured message. Images can be sent
as email attachments.
Triggered Event
A Triggered event is activated from, e.g:
• a switch connected to an input port on the AXIS 215 PTZ
• a manually activated action e.g. from an action button in the web interface
• on restart (reboot) after e.g. power loss
Note: AXIS 215 PTZ-E does not support I/O ports.
How to set up a triggered event
This example describes how to set the AXIS 215 PTZ/AXIS 215 PTZ-E to upload images when the main door is
opened:
1. Click Add triggered on the Event types page.
2. Enter a descriptive name for the event, such as Motion Detection. To configure motion detection see page
3. Set the Priority - High, Normal or Low (see online help files).
4. Set the Respond to Trigger... parameters when the event is to be active, for example. only after office
hours.
5. Select the trigger alternative from the Triggered by... drop-down list, e.g. on restart.
6. Set the When Triggered... parameters i.e. set what the AXIS 215 PTZ/AXIS 215 PTZ-E is to do if motion is
detected, e.g. upload images to an FTP server or send an e-mail.
7. Click OK to save the Event in the Event Types list.
Please use the online help
for descriptions of each available option. Image file names can be formatted
according to specific requirements, such as time/date or type of triggered event. See File Naming & Date/Time
Formats under Event Configuration.
Please use the online help files
for descriptions of each available option.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Event Configuration
Pre-trigger and Post-trigger buffers
This function is very useful when checking to see what happened immediately before and after a trigger, e.g. 2
minutes before and after a door has been opened. Check the Upload images checkbox under Event Types > Add
Triggered... > When Triggered... to expand the web page with the available options.
Note: Buffer size - up to 9 MB buffer. The maximum length of time of the pre-/post-buffer depends on the
image size and selected frame rate.
Include pre-trigger buffer - images stored internally in the server from the time immediately preceding the
trigger. Check the box to enable the pre-trigger buffer, enter the desired length of time and specify the required
image frequency.
Include post-trigger buffer - contains images from the time immediately after the trigger. Configure as for
pre-trigger.
Note: If the pre- or post-buffer is too large for the internal memory, the frame rate will be reduced and individual images may be missing. If this
occurs, an entry will be created in the unit's log file.
Continue image upload (unbuffered) - enable the upload of images for a fixed length of time. Specify the
length of time for the uploaded recording, in seconds, minutes or hours, or for as long as the trigger is active.
Finally, set the desired image frequency to the maximum (the maximum available) or to a specified frame rate.
The frame rate will be the best possible, but might not be as high as specified, especially if uploading via a slow
connection.
Scheduled Event
A Scheduled event can be activated at pre-set times, in a repeating pattern on selected weekdays.
How to set up a scheduled event
This example describes how to set the AXIS 215 PTZ/AXIS 215 PTZ-E to send an email notification with saved
images from a set time:
1. Click Add scheduled on the Event types page.
2. Enter a descriptive name for the event, e.g. Scheduled email.
3. Set the Priority (High, Normal or Low).
4. Set the Activation Time parameters (24h clock) when the event is to be active, e.g. start on Fridays at
18.00 with a duration of 62 hours.
5. Set the When Activated... parameters i.e. set what the AXIS 215 PTZ/AXIS 215 PTZ-E is to do at the
specified time e.g. send uploaded images to an email address.
6. Click OK to save the Event in the Event Types list.
Please use the online help files
for descriptions of each available option.
Motion Detection
In the Motion Detection menu, you can configure the AXIS 215 PTZ/AXIS 215 PTZ-E for motion detection. The
motion detection feature is used to generate an alarm whenever movement occurs (or stops) in the image. The
AXIS 215 PTZ/AXIS 215 PTZ-E can use a maximum of 10 Include/Exclude windows.
• Include windows target specific areas within the image
• Exclude windows are areas to be ignored within the Include window
Once configured, the motion detection windows will appear in a list when motion detection is selected to trigger
Note: Using the motion detection feature may decrease overall performance in the camera.
Motion detection will not function while the lens is moving (i.e. pan, tilt, zoom)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Event Configuration
How to configure Motion Detection
This example describes how to configure motion detection:
1. Click Motion Detection in the Event Configuration menu.
2. Click the Configure Included Windows radio button.
3. Click New.
4. Enter a descriptive name of your choice under Windows name.
5. Adjust the size (drag the bottom right-hand corner) and position (click on the text at the top and drag
to the desired position).
6. Adjust the Object size, History and Sensitivity profile sliders (see table below for details). Any detected
motion within an active window is then indicated by red peaks in the Activity window (the active
window has a red frame).
7. Click Save.
If there are parts of the Include window that you wish to exclude, click the
Configure Excluded Windows radio button and repeat steps 1-7 above.
Please use the online help
for descriptions of each available option.
Parameter
History
Sensitivity
Size
High
Only very large objects trigger An object that appears in the region will trigger Ordinary colored objects against ordinary back-
motion detection the motion detection for a long period grounds will trigger the motion detection
Even very small objects trigger An object that appears in the region will trigger Only very bright objects against a dark back-
Low
motion detection
motion detection for only a very short period
ground will trigger motion detection
Default val-
ues
Low
Medium to High
Medium to High
Examples:
•
•
Avoid triggering on small objects in the image by selecting a high size level.
To trigger motion detection as long as there is activity in the area, select a high history level.
•
To only detect flashing light, low sensitivity can be selected. In other cases, a high sensitivity level is recommended.
Port Status (AXIS 215 PTZ only)
Under Event Configuration > Port Status there is a list that shows the status for the connected inputs and
outputs of the AXIS 215 PTZ for the benefit of the Operator who cannot access the System Options section.
Example: If the Normal state for a push button connected to an input is set to Inactive - as long as the button is not pushed, the state is
inactive. If the button is pushed, the state of the input changes to active.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
System Options
Security
User access control is enabled by default, the administrator sets the root password on first access. Other users are
authorized with user names and passwords, or the administrator can choose to allow anonymous viewer login to
the Live View page, as described below:
Users - the user list displays the authorized users and access levels:
• Viewer - the lowest level of access, which only allows the user access to the Live View page.
• Operator - an Operator can view the Live View page, create and modify event types and adjust certain
other settings. The Operator does not have access to the Systems Options configuration pages.
• Administrator - an administrator has unrestricted access to the Setup Tools and can determine the regis-
tration of all other users.
User Settings - check the corresponding checkboxes to enable:
• Anonymous viewer login - allows any viewer direct access to the Live View page.
• Maximum number of simultaneous viewers - enter a value here to restrict the number of unicast viewers
accessing the unit. This is useful if you need to save on bandwidth. (Note that all multicast viewers count
as 1 viewer.)
• Anonymous PTZ control login - allows any viewer access to the Pan/Tilt/Zoom controls on the Live View
page.
IP Address Filter
Enable IP Address Filtering - to allow or deny access to the AXIS 215 PTZ/AXIS 215 PTZ-E, check the box
Enable IP address filtering. Once enabled, the IP addresses in the list will be allowed or denied access according
to the choice made in the drop-down list Allow/Deny the following IP addresses.
The administrator can add up to 256 IP address ranges or single IP addresses to the Filtered IP Addresses list. If
IP address filtering is enabled, the AXIS 215 PTZ/AXIS 215 PTZ-E will allow or deny requests coming from the
IP addresses in the list.
See the IP address filtering help files
for information on how to add IP address ranges.
The users from these IP addresses need to be specified in the user list with the appropriate access rights (User,
Operator or Administrator).
Referrals - to prevent unauthorized sources from including the video stream from the AXIS 215 PTZ/AXIS 215
PTZ-E into external Web pages, check the Referrals checkbox and enter the IP address or Host name of the
computer that hosts the Web pages with the included video stream. Several IP addresses/host names can be
defined and are separated by semicolons(;)
HTTPS
For greater security, the AXIS 215 PTZ/AXIS 215 PTZ-E can be configured to use HTTPS (Hypertext Transfer
Protocol over SSL (Secure Socket Layer)). That is, all communication that would otherwise go via HTTP will
instead go via an encrypted HTTPS connection.
Certificate - to use HTTPS for communication with the AXIS 215 PTZ/AXIS 215 PTZ-E, a Certificate must be
created using one of the following methods:
• A self-signed certificate can be created in the network camera, but this does not guarantee the same level of
security as an official certificate.
• An official certificate issued by a CA (Certificate Authority). A CA issues and manages security credentials
and public keys for message encryption.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
1. Click either Create self-signed certificate or Create Certificate Request and enter the required
information in the provided fields.
2. Click OK.
3. Create self-signed certificate generates and installs a certificate which will be displayed under Installed
Certificate.
Create Certificate Request generates a PEM formatted request which you copy and send to a CA for
signing. When the signed certificate is returned, click Install signed certificate... to install the certificate
in the AXIS 215 PTZ/AXIS 215 PTZ-E.
4. Set the HTTPS Connection Policy for the administrator, Operator and Viewer to enable HTTPS connection
(set to HTTP by default)
Please refer to the home page of your preferred CA for information on where to send the request etc. For more
information, please refer to the online help files
802.1X - Network Admission Control
IEEE 802.1X is an IEEE standard for port-based Network Admission Control. It provides authentication to
devices attached to a network port (wired or wireless), establishing a point-to-point connection, or, if
authentication fails, preventing access on that port. 802.1X is based on EAP (Extensible Authentication
Protocol).
In an 802.1X enabled network switch, clients equipped with the correct software can be authenticated and
allowed or denied network access at the Ethernet level.
Clients and servers in an 802.1X network may need to authenticate each other by some means. In the Axis
implementation this is done with the help of digital certificates provided by a Certification Authority. These are
then validated by a third-party entity, such as a RADIUS server, examples of which are Free Radius and
Microsoft Internet Authentication Service.
To perform the authentication, the RADIUS server uses various EAP methods/protocols, of which there are
many. The one used in the Axis implementation is EAP-TLS (EAP-Transport Layer Security).
The AXIS network video device presents its certificate to the network switch, which in turn forwards this to the
RADIUS server. The RADIUS server validates or rejects the certificate and responds to the switch, and sends its
own certificate to the client for validation. The switch then allows or denies network access accordingly, on a
pre-configured port.
The authentication process
1. A CA server provides the required signed certificates.
2. The Axis video device requests access to the protected network at the network switch. The switch
forwards the video device’s CA certificate to the RADIUS server, which then replies to the switch.
3. The switch forwards the RADIUS server’s CA certificate to the video device, which also replies to the
switch.
4. The switch keeps track of all responses to the validation requests. If all certificates are validated, the
Axis video device is allowed access to the protected network via a pre-configured port.
RADIUS (Remote Authentication Dial In User Service) - AAA (Authentication, Authorization and Accounting)
protocol for applications such as network access or IP mobility. It is intended to work in both local and roaming
situations.
CA servers - In cryptography, a Certification Authority (CA) is an entity that provides signed digital certificates
for use by other parties, thus acting a trusted third party. There are many commercial CA’s that charge for their
services. Institutions and governments may have their own CA, and there are free CA’s available.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
Date & Time
Current Server Time - displays the current date and time (24h clock). If this has not been configured, the time
displayed is the default setting. The time can be displayed in 12h clock format in the Overlay Images (see below).
New Server Time - Select your time zone from the drop-down list and check the daylight saving time changes,
if desired.
From the Time Mode section, select the preferred method to use for setting the time:
• Synchronize with computer time - sets the time from the clock on your computer.
• Synchronize with NTP Server - the AXIS 215 PTZ/AXIS 215 PTZ-E will obtain the time from an NTP server every
60 minutes. Specify the NTP server's IP address or host name.
Note that if using a host name for the NTP server, a DNS server must be configured under TCP/IP settings. See
Network > TCP/IP below.
• Set manually - this option allows you to manually set the time and date.
Date & Time Format Used in Images - specify the formats for the date and time (12h or 24h) displayed in the
Live View video streams.
Use the predefined formats or use your own custom date and time formats. See Advanced File Naming &
Date/Time Formats in the help files
for information on how to create your own file formats.
Network
Basic TCP/IP Settings
The AXIS 215 PTZ/AXIS 215 PTZ-E supports both IP version 4 and IP version 6. Both versions may be enabled
simultaneously, and at least one version must always be enabled.
IPv4 Address Configuration - when using IPv4, the IP address for the AXIS 215 PTZ/AXIS 215 PTZ-E can be
set automatically via DHCP, or a static IP address can be set manually.
IPv6 Address Configuration - If IPv6 is enabled, the AXIS 215 PTZ/AXIS 215 PTZ-E will receive an IP address
according to the configuration in the network router.
There are also options for setting up notification of changes in the IP address, and for using the AXIS Internet
Dynamic DNS Service. For more information on setting the IP address, please see the online help.
Notes: • DHCP is a protocol for automatic IP address assignment on a network. IP address assignment via DHCP may lead to the situation
where the IP address changes and you lose contact. Configure the options for notification of IP address change (under Services) to
receive notification from the network camera when the IP address changes.
• Alternatively, if your DHCP server can update a DNS server, you can access the AXIS 215 PTZ/AXIS 215 PTZ-E by host name which is
always the same, regardless of the IP address.
For more information, please refer to the online help files
Services
Enable ARP/Ping setting of IP address - The IP address can be set using the ARP/Ping method, which associates
the unit's MAC address with an IP address. Check this box to enable the service. Leave disabled to prevent
unintentional resetting of the IP address.
Notes: • The ARP/Ping service is automatically disabled 2 minutes after the unit is started, or as soon as an IP address is set.
• Pinging the unit will still be possible when this service is disabled.
Options for notification of IP address change - if the IP Address for the AXIS 215 PTZ/AXIS 215 PTZ-E is
changed automatically, e.g. by DHCP, you can choose to be notified. Click Settings... and enter the required
information.
AXIS Internet Dynamic DNS Service - If the AXIS 215 PTZ/AXIS 215 PTZ-E has been registered with the Axis
Internet Dynamic DNS service and the IP address for the product changes, the service is updated to reflect the
change. Check the box to enable/disable automatic updates.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
The domain name currently registered at the Axis Internet Dynamic DNS service for your product can at any
time be removed. To do this click Settings... and follow the instructions.
For more information, please refer to the online help files
Advanced TCP/IP Settings
DNS Configuration - DNS (Domain Name Service) provides the translation of host names to IP addresses on
your network.
Obtain DNS server address via DHCP - automatically use the DNS server settings provided by the DHCP server.
Click the View button to see the current settings.
Use the following DNS server address - enter the desired DNS server by specifying the following:
• Domain name - enter the domain(s) to search for the host name used by the AXIS 215 PTZ/AXIS 215 PTZ-E.
Multiple domains can be separated by semicolons (;). The host name is always the first part of a Fully Qualified
Domain Name, e.g. myserver is the host name in the Fully Qualified Domain Name myserver.mycompany.com
where mycompany.com is the Domain name.
• Primary DNS server - enter the IP address of the primary DNS server.
• Secondary DNS server - will be used if the primary DNS server is unavailable.
NTP Configuration - The AXIS 215 PTZ/AXIS 215 PTZ-E can obtain the correct time from an NTP server. The
address for the NTP server can either be obtained via the DHCP server, or it can be entered manually.
Host Name Configuration - The AXIS 215 PTZ/AXIS 215 PTZ-E can be accessed using a host name, instead of
an IP address. The host name is usually the same as the assigned DNS Name. It is always the first part of a Fully
Qualified Domain Name and is always one word, with no period. For example, myserver is the host name in the
Fully Qualified Domain Name myserver.mycompany.com.
The enable dynamic DNS updates allows you to alias a dynamic IP address to a static host name, allowing your
computer to be more easily accessed from various locations on the Internet. Outside users can always access
your server using the associated DNS name regardless of the WAN IP. The DNS server used by the user and/or
the DNS server responsible for the domain in use must support RFC2136 and allow updates from the camera.
The TTL (Time To Live) value determines how long (in seconds) the reply from the DNS server should be
remembered when checking that the domain name for the registered IP address is still valid.
Link-Local IPv4 Address
This is enabled by default and assigns the AXIS 215 PTZ/AXIS 215 PTZ-E an additional IP address for use with
UPnP™. The AXIS 215 PTZ/AXIS 215 PTZ-E can have both a Link-Local IP and a static/DHCP-supplied IP
address at the same time - these will not affect each other.
HTTP - The default HTTP port number (port 80) can be changed to any port within the range 1024-65535. This
is useful for e.g. simple security port mapping.
HTTPS - If applicable, enter the HTTPS port the AXIS 215 PTZ/AXIS 215 PTZ-E will use. The default setting
(443) can be changed to any port within the range 1024-65535. HTTPS is used to provide encrypted web
browsing.
NAT Traversal (port mapping) for IPv4 - Use NAT traversal when your AXIS 215 PTZ/AXIS 215 PTZ-E is
located on an intranet (LAN) and you wish to make it available from the other (WAN) side of a NAT router. With
NAT traversal properly configured, all HTTP traffic to an external HTTP port in the NAT router will be forwarded
to the network camera.
Enable/Disable - When enabled, the AXIS 215 PTZ/AXIS 215 PTZ-E will attempt to configure port mapping in
a NAT router on your network, using UPnP™.
Use manually selected NAT router - Select this option to manually select a NAT router. Enter the IP address for
the router in the field provided.
If a router is not manually specified, the AXIS 215 PTZ/AXIS 215 PTZ-E Network Camera will automatically
search for NAT routers on your network. If more than one router is found, the default router will be selected.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
Alternative HTTP port - Select this option to manually define an external HTTP port. Enter the port number in
the field provided. If no port is entered here a port number will automatically be selected when NAT traversal is
enabled.
FTP - The FTP server running in the AXIS 215 PTZ/AXIS 215 PTZ-E enables the upload of e.g. new firmware,
user applications, etc. Check the box to enable the service.
RTSP - The RTSP protocol allows a connecting client to start an MPEG-4 stream. Enter the RTSP port number to
use. The default setting is 554.
Network Traffic
The default setting is Auto-negotiate which means that the correct speed is automatically selected. If necessary,
you can set the connection speed by selecting it from the drop-down list. 10BaseT (Half/Full Duplex),
100BaseTX (Half/Full Duplex).
Maximum bandwidth - Specify, in Mbit/s or Kbit/s, the maximum bandwidth that the AXIS 215 PTZ/AXIS 215
PTZ-E is allowed to use on your network. This is a useful function when connecting the AXIS 215 PTZ/AXIS
215 PTZ-E to busy or heavily loaded networks. The default setting is Unlimited.
For more information, please refer to the online help files
Network - SOCKS
SOCKS is a networking proxy protocol. The AXIS 215 PTZ/AXIS 215 PTZ-E can be configured to use a SOCKS
server to reach networks on the other side of a firewall/proxy server. This functionality is useful if the AXIS 215
PTZ/AXIS 215 PTZ-E is located on a local network behind a firewall, but notifications, uploads, alarms, etc.,
need to be sent to a destination outside the local network (e.g. to the Internet).
Network - QoS (Quality of Service)
Quality of Service (QoS) provides the means to guarantee a certain level of a specified resource to selected traffic
on a network. Quality can be defined as e.g. a maintained level of bandwidth, low latency, no packet losses, etc.
The main benefits of a QoS-aware network can be summarized as:
• The ability to prioritize traffic and thus allow critical flows to be served before flows with lesser priority.
• Greater reliability in the network, thanks to the control of the amount of bandwidth an application may
use, and thus control over bandwidth races between applications.
The QoS in Axis network video products marks the data packets for various types of network traffic originating
from the product. This makes it possible for network routers and switches to e.g. reserve a fixed amount of
bandwidth for these types of traffic. The types of traffic marked by the camera are video, audio, event/alarm and
management network traffic.
QoS DSCP Settings
For each type of network traffic supported by your Axis network video product, enter a DSCP (Differentiated
Services Codepoint) value. This value is used to mark the traffic’s IP header. When the marked traffic reaches a
network router or switch, the DSCP value in the IP header tells the router or switch which type of treatment to
apply to this type of traffic, for example, how much bandwidth to reserve for it.
Note that DSCP values can be entered in decimal or hex form, but saved values are always shown in decimal.
Network - SMTP (email)
Simple Mail Transfer Protocol (SMTP) - enter the host names or addresses for your primary and secondary mail
servers in the fields provided to enable event and error email messages from the AXIS 215 PTZ/AXIS 215 PTZ-E
to predefined addresses, via SMTP.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
Network - SNMP
The Simple Network Management Protocol (SNMP) allows remote management of network devices. Depending
on the level of security required, select the version of SNMP to use. The three levels of security are:
• SNMP V1 - includes no security.
• SNMP V2c - uses simple security. The community name can be specified as a password for read or read/write
access to all supported SNMP objects. The community is the group of network devices using SNMP.
• SNMP V3 - provides encryption and secure passwords. HTTPS must be enabled.
Network - UPnP
The AXIS 215 PTZ/AXIS 215 PTZ-E includes support for UPnP in Windows Millennium and Windows XP. UPnP
is enabled by default.
Note: UPnP must be installed on your workstation. To do this, open the Control Panel from the Start Menu and select Add/Remove Programs.
Select Add/Remove Windows Components and open the Networking Services section. Click Details and then select UPnP.
Network - RTP/MPEG-4
Multicast must be enabled for these settings to take effect. The settings are only valid when MPEG-4 is used as
the video format. These settings are the port range, IP address, port number, and Time-To-Live value to use for
the video stream(s) in MPEG-4 format. Only certain IP addresses and port numbers should be used for multicast
streams.
Enter the port range, IP address and the port number to use for the video and audio streams in the required
fields. (AXIS 215 PTZ-E does not support audio.)
Only IP addresses within certain ranges can be used for multicasting. The camera has been pre-configured with
an address from these ranges, and this does not normally need to be changed. Please contact your network
administrator if you have special requirements.
Notes: • Viewers do not need to know this IP address or port number, but simply the main IP address or host name otherwise used for accessing
the camera.
• Setting the video port number to 0 means a random port number will be used.
If IP packets (i.e. data) fail to be delivered to their destination within a reasonable length of time the number
entered in the Time to live field tells the network routers when to discard the packet. The value is usually
measured in ‘hops’, i.e. the number of network routers that can be passed before the packet arrives at its
destination or is dropped.
Network - Bonjour
The AXIS 215 PTZ/AXIS 215 PTZ-E includes support for Bonjour. When enabled, the camera is automatically
detected by operating systems and clients that support this.
Ports & Devices - I/O Ports (for AXIS 215 PTZ only)
Ports can be given descriptive names and their Normal state can be configured.
The 2 options for Normal state are Open circuit and Grounded circuit. The input is activated when the Current
state changes so that it no longer equals the Normal state.
As an example, if the Normal state for a pushbutton connected to an input is Open circuit, this means that as
long as the button is not pushed (and the Current state remains as Open Circuit), the state will be inactive.
For more information, please refer to the online help files
32
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
Maintenance
• Restart - the unit is restarted without changing any of the settings. Use this method if the unit is not behav-
ing as expected.
• Restore - the unit is restarted and most current settings are reset to factory default values. The settings that
will not be reset are as follows:
• boot protocol (DHCP or static)
• static IP address
• default router
• subnet mask
• system time
• Default - the Factory default button should be used with caution. Pressing this button will reset all of the
AXIS 215 PTZ/AXIS 215 PTZ-E's settings to the factory default values (including the IP address).
PTZ Status - click the Test button to check the pan, tilt, zoom mechanics and camera for errors. If you receive
Backup - click the Backup button to take a backup of all of the parameters, and any user-defined scripts. If
necessary, it is then possible to return to the previous settings if the settings are changed and there is
unexpected behavior.
Note: The root password will also be reset to the password saved in the backup file.
Restore - click the Browse button to locate the saved backup file (see above) and then click the Restore button.
The settings will be restored to the previous configuration.
Note: Backup and Restore can only be used on the same unit running the same firmware. This feature is not intended for multi-configura-
tions or for firmware upgrades.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - System Options
Support
The support overview page provides valuable information on troubleshooting and contact information, should
you require technical assistance.
Support - System Overview is a quick look over the camera’s status and settings. Information that can be
found here includes the camera’s Firmware version, IP address, Security, Event and Image settings and Recent
log items. Many of the captions are also links to the proper Setup page to conveniently make adjustments in the
camera’s settings.
Support - Logs & Reports - when contacting Axis support, please be sure to provide all relevant information:
Logs - the Log report including all log information
Reports - the Server Report and Parameter List provide valuable information for troubleshooting, be sure to
include the server report when contacting Axis’ support service.
Configuration
• Log Level for Log Files - from the drop-down list, select the level of information to be added to the Log file
• Log Level for Email - from the drop-down list, select the level of information to send as email and enter the
destination email address.
Advanced
Scripting is an advanced function that provides the possibility to customize and use scripts. This function is a
very powerful tool.
Caution!
Improper use may cause unexpected behavior or even cause loss of contact with the unit. If a script does cause
problems, reset the unit to its factory default settings. A backup file may be of use to return the unit to its latest
configuration.
Axis strongly recommends that you do not use this function unless you fully understand the consequences.
Note that Axis support does not provide assistance for problems with customized scripts.
Plain Config - this function is for the advanced user with experience of Axis network camera configuration. All
parameters can be set and modified from this page. Help is available from the standard help pages.
Resetting to Factory Default Settings
To reset the AXIS 215 PTZ/AXIS 215 PTZ-E to the original default settings, go to the System Options >
PTZ/AXIS 215 PTZ-E as described below:
Using the Reset Button
Follow the instructions below to reset the AXIS 215 PTZ/AXIS 215 PTZ-E to factory default settings using the
Reset Button.
1. Switch off the AXIS 215 PTZ/AXIS 215 PTZ-E by disconnecting the power supply.
2. Press and hold the Reset button while you reconnect the power connector.
3. Keep the Reset button pressed for approximately 15 seconds.
4. Release the Reset button.
Note: Resetting to the factory default settings using the Reset Button will cause all parameters (including the IP address) to be reset. Refer to
34
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Unit Connectors
Unit Connectors
This section describes the following:
• The I/O terminal block (for AXIS 215 PTZ only)
• LED indicators
• Power connection
Note: AXIS 215 PTZ-E does not support audio and does not have I/O ports.
Audio in
Audio out
Status/network/power
Indicator LEDs
Network connector
I/O terminal
connector
Control button
Power connector
AXIS 215 PTZ Network Camera
I/O terminal connector (for AXIS 215 PTZ only)
Used in applications for e.g. motion detection, event triggering, time lapse recording
and alarm notifications. It provides the interface to:
• 1 transistor output - For connecting external devices such as relays and
LEDs. Connected devices can be activated by VAPIX®, output buttons on
the Live View page or by an Event Type. The output will show as active
(shown under Event Configuration > Port Status) if the alarm device is
activated.
Pin 4
Pin 2
Pin 1
Pin 3
• 1 digital input - An alarm input for connecting devices that can toggle between an open and closed
circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received
the state changes and the input becomes active (shown under Event Configuration > Port Status).
• Auxiliary power and GND
Function
Pin number
Notes
Specifications
GND
1
2
Ground
12V DC
Power
Can be used to power auxiliary equipment. Note that the AXIS 215 PTZ itself
cannot be powered via the I/O terminal connector.
Max load = 100mA
Digital
Input
3
4
Connect to GND to activate, or leave floating (or unconnected) to deactivate.
Must not be exposed to voltages
greater than 12V DC
Transistor
Output
Uses an open-collector NPN transistor with the emitter connected to the
GND pin. If used with an external relay, a diode must be connected in paral-
lel with the load, for protection against voltage transients.
Max load = 100mA
Max voltage = 24V DC
(to the transistor)
Network connector - RJ-45 Ethernet connector. Using shielded cables is recommended.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Connection diagram
Power connector - Mini DC connector 12V DC ±5%, max 11.5W. See product label for ± connection.
Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo
signal).
Audio out - Audio output (line level) that can be connected to a public address (PA) system or an active speaker
with a built-in amplifier. A pair of headphones can also be attached. A stereo connector must be used for the
audio out.
Connection diagram
AXIS 215 PTZ
1
o
e.g. pushbutton
12V
max. 100mA
2
o
z
3
o
4
o
LED indicators
LED
Color
Indication
Network Green
Amber
Steady for connection to a 100 Mbit/s network. Flashes for network activity.
Steady for connection to 10 Mbit/s network. Flashes for network activity.
No network connection.
Unlit
Status
Power
Green
Amber
Red
Steady green for normal operation.
Steady during startup, during reset to factory default or when restoring settings.
Slow flash for failed upgrade.
Green
Amber
Normal operation.
Flashes green/amber during firmware upgrade.
Power connection
Connect the supplied indoor power adapter to the power connector in the camera casing.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Troubleshooting
Troubleshooting
Checking the Firmware
The firmware is software that determines the functionality of the AXIS 215 PTZ/AXIS 215 PTZ-E. When you
download firmware from the Axis Website, your Axis product will receive the latest available functionality.
One of your first actions when troubleshooting a problem should be to check the currently installed firmware
version. The latest version may contain a correction that fixes your particular problem. The current software
version in your AXIS 215 PTZ/AXIS 215 PTZ-E is available under Setup > Basic Configuration.
Updating the Firmware
New firmware can be downloaded to the AXIS 215 PTZ/AXIS 215 PTZ-E over the network. Always read the
upgrade instructions available with each new release, before updating the firmware.
1. Save the firmware file to your computer. The latest version of the AXIS 215 PTZ/AXIS 215 PTZ-E
firmware is available free of charge from the Axis Website at http://www.axis.com/techsup or from your
local distributor.
2. Go to Setup > System Options > Maintenance in the AXIS 215 PTZ/AXIS 215 PTZ-E Web pages.
3. In the Upgrade Server section and browse to the firmware file on your computer. Click Upgrade.
4. Wait at least 20 minutes before restarting the AXIS 215 PTZ/AXIS 215 PTZ-E after upgrading.
Notes: • Pre-configured and customized settings will be retained for use when the new firmware is running (providing that the features are
available in the new firmware) although this is not guaranteed by Axis Communications.
• After starting the process, you should always wait at least 20 minutes before restarting the AXIS 215 PTZ/AXIS 215 PTZ-E, even if you
suspect the procedure has failed.
• Your dealer reserves the right to charge for any repair attributable to faulty updating by the user.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Troubleshooting
Customer Services
If you contact the Axis support desk, please help us help you resolve your problems expediently by providing a
server report, log file and a brief description of the problem.
Server Report - go to Setup > System Options > Support Overview. The server report contains important
information about the server and its software, as well as a list of the current parameters.
Log file - go to Setup > System Options > Logs & Reports. The Log file records events within the unit since the
last restart of the system and can prove a useful diagnostic tool for troubleshooting.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Troubleshooting
Symptoms, Possible Causes and Remedial Actions
Problems setting the IP address
Using ARP Ping
The IP address must be set within two minutes after the power has been applied to the AXIS 215 PTZ/AXIS 215 PTZ-E,
restart the server and try again. Also, make sure the ping length is set to 408.
The AXIS 215 PTZ/AXIS 215 PTZ-E is
located on a different subnet
If the IP address intended for the AXIS 215 PTZ/AXIS 215 PTZ-E and the IP address of your computer are located on
different subnets, you will not be able to set the IP address. Contact your network administrator for an IP address on
the same subnet as the computer you are performing the installation from.
The IP address is being used by another Disconnect power from the AXIS 215 PTZ/AXIS 215 PTZ-E.
device Run the Ping command (in a Command/DOS window, type ping and the IP address of the unit).
If you receive: Reply from <IP address>: bytes = 32; time = 10 ms..... - this means that the IP address may already
be in use by another device on your network. You must obtain a new IP address and reinstall the unit.
If you receive: Request timed out - this means that the IP address is available for use with your AXIS 215 PTZ/AXIS
215 PTZ-E. In this case, check all cabling and reinstall the unit.
The AXIS 215 PTZ/AXIS 215 PTZ-E cannot be accessed from a browser
The IP address has been changed by
DHCP
1) Move the AXIS 215 PTZ/AXIS 215 PTZ-E to an isolated network or to one with no DHCP or BOOTP server. Set the IP
address again, using the ARP Ping command.
2) Access the unit and disable BOOTP and DHCP in the TCP/IP settings. Return the unit to the main network. The unit
now has a fixed IP address that will not change.
3) As an alternative to 2), if dynamic IP address via DHCP or BOOTP is required, select the required service and then
configure IP address change notification from the network settings. Return the unit to the main network. The unit will
now have a dynamic IP address, but will notify you if the address changes.
Other networking problems
Test the network cable by connecting it to another network device, then Ping that device from your workstation.
Cannot send notifications, uploads, alarms, etc, to a destination outside the local network.
Firewall protection The AXIS 215 PTZ/AXIS 215 PTZ-E can be configured to use a SOCKS server to reach networks on the other side of a
firewall/proxy server.
Your AXIS 215 PTZ/AXIS 215 PTZ-E is accessible locally, but not externally
Firewall protection
Check the Internet firewall with your system administrator.
Default routers required
Check if you need to configure the default router settings.
The Internet site is too heavily loaded
Use a script running on your web server to relay images from the AXIS 215 PTZ/AXIS 215 PTZ-E to the Internet.
A firmware upgrade has been interrupted A rescue firmware is running in the product. First, set the IP address using AXIS IP utility or ARP and Ping,
or the firmware has in some other way
been damaged
Then, from a Web browser, access the unit and download the latest firmware to the product, see Updating the Firm-
Problems with the MPEG-4 format
No MPEG-4 displayed in the
client.
Check that the correct network interface is selected in the AMC control panel applet (network tab).
Check that the relevant MPEG-4 connection methods are enabled in the AMC control panel applet (network tab).
In the AMC control applet, select the MPEG-4 tab and click the button Set to default MPEG-4 decoder.
No multicast MPEG-4 displayed in the
client.
Check with your network administrator that the multicast addresses used by the
AXIS 215 PTZ/AXIS 215 PTZ-E are valid for your network.
Check with your network administrator to see if there is a firewall preventing viewing.
Multicast MPEG-4 only accessible by
local clients.
Check if your router supports multicasting, or if the router settings between the client and the server need to be con-
figured. The TTL (Time To Live) value may need to be increased.
Poor rendering of MPEG-4 images
Color depth set incorrectly on clients. Set to 16-bit or 32-bit color.
If text overlays are blurred, or if there are other rendering problems, you may need to enable Advanced Video Render-
ing from the MPEG-4 tab in the AMC control panel applet.
Ensure that your graphics card is using the latest device driver. The latest drivers can usually be downloaded from the
manufacturer's website.
Color saturation is different in MPEG-4 Modify the settings for your graphics adapter. Please see the adapter's documentation for more information.
and Motion JPEG.
Lower frame rate than expected.
Reduce number of applications running on the client computer.
Check with the system administrator that there is enough bandwidth available. See also the online help.
Check in the AMC control panel applet (MPEG-4 tab) that video processing is not set to Decode only I frames.
Lower the image resolution.
Image degeneration.
Decrease the GOV length, see the online help for more information.
No images displayed in the Web interface
Problem with AMC
(Internet Explorer for Windows only)
To enable the updating of images in Microsoft Internet Explorer for Windows, set your Web browser to allow ActiveX
controls. Also, make sure that AXIS Media Control (AMC) component is installed on your workstation.
Installation of additional ActiveX compo- Configure your AXIS 215 PTZ/AXIS 215 PTZ-E to use a Java applet for updating the images under
nent restricted or prohibited
Live View Config > Layout > Default Viewer for Internet Explorer. See help files for more information.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Troubleshooting
Video Image Problems
Distorted colors
Problems may occur if the image contains no white color at all, or if the dominant color is not white. In these circum-
stances, the white balance may incorrectly be based on another visible color in the image, and colors may become dis-
torted. A pale background picture with reddish or blue foreground objects is very symptomatic of this condition. In
such cases it is recommended that a fixed white balance setting is selected.
Image too dark or too light
Problems uploading own files
See the help on Video & Image Settings.
There is only limited space available for the upload of your own files. Try deleting one or more existing files, to free up
space.
Missing images in uploads
Slow image update
This can occur when trying to use a larger image buffer than is actually available. Try lowering the frame rate or the
upload period.
Configuring, e.g. pre-buffers, hi-res images, high frame rate etc will reduce the performance of the AXIS 215 PTZ/AXIS
215 PTZ-E.
Slow performance
Slow performance may be caused by e.g. heavy network traffic, many users with access to unit, low performing client,
use of features such as Event handling., Image rotation.
Bad snapshot images
Display incorrectly configured on your
workstation
In Display Properties, configure your display to show at least 65000 colors, i.e. at least 16-bit.
Using only 16 or 256 colors on your display will produce dithering artifacts in the image.
Audio problems (AXIS 215 PTZ only)
No audio
Check that:
•
•
•
•
•
PC sound card, speakers and microphone are correctly connected
the Mute button is not pressed
the volume in and volume out settings are correct
all cabling is connected
the value of the Post Content Length in your proxy server is 1MB or more. You may need to contact your system
administrator to do this.
No full-duplex function
Poor performance
Incorrect configuration. Check the setting in the camera’s Setup pages.
Sound card does not support full-duplex. For information on how to check if your sound card supports full-duplex,
Too many users/clients connected. Try limiting the number of clients allowed to connect.
Low bandwidth. Reduce the Speed setting on the Audio settings page. Setting lower speed will reduce any break-up in
the sound, but will also increase the transmission delay. If running in Full-Duplex mode, try switching to Half-Duplex
mode.
Whining or screeching sound from speak- Poor positioning of speakers and/or microphone. Relocate the speakers or microphone so that they do not point
ers (feedback)
towards each other, and/or lower the volume.
Mechanical problems
problem with pan, tilt, zoom mechanics Click the PTZ Status - Test button under System Options > Maintenance to check the pan, tilt, zoom mechanics and
camera for errors. If you receive an error message as the result of this test, contact Axis Customer Services at
For additional assistance, please contact your reseller or check the product’s support pages on the Axis
40
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
Technical Specifications
Item
Specification
Models
• AXIS 215 PTZ - 60Hz
• AXIS 215 PTZ - 50Hz
• AXIS 215 PTZ-E 60Hz(NTSC)
• AXIS 215 PTZ-E 50Hz (PAL)
Image sensor
Lens
1/4” sony Interlaced CCD
F1.6-F2.7
f=3.8-46mm
Automatic day/night
Autofocus
Focus range: 300 mm (wide) or 1000 mm (tele) to infinity
Angle of view
Zoom
4.4° - 51.6° horizontal
12x optical and 4x digital, total 48x
Minimum illumination
Color: 1 lux at 30 IRE, F1.6
B/W: 0.3 lux at 30 IRE, F1.6
Pan Range
Tilt Range
Max speed
+/-170° (360° panning via Auto-flip)
180°
Pan: 180°/sec
Tilt: 140°/sec
Video compression
Resolutions
Motion JPEG
MPEG-4 Part 2 (ISO/IEC 14496-2), ASP level 0-5, SP level 0-3
4CIF, 2CIFExp, 2CIF, CIF, QCIF
Max 704x480 (NTSC) 704x576 (PAL)
Min 176x120 (NTSC) 176x144 (PAL)
Frame rate
(NTSC/PAL)
Motion JPEG:
Up to 30/25 fps in all resolutions
MPEG-4 (AXIS 215 PTZ):
•
•
Up to 30/25 fps at 2CIF/CIF/QCIF
Up to 25/21 fps at 4CIF/2CIFExp
MPEG-4 (AXIS 215 PTZ-E)
•
Up to 30/25 (NTSC/PAL) in 2CIF/CIF/QCIF
•
Up to 26/22 (NTSC/PAL) in 4CIF/2CIFExp
Video streaming
Image settings
Simultaneous Motion JPEG and MPEG-4
Controllable frame rate and bandwidth
Constant and variable bit rate (MPEG-4)
3GPP and ISMA compatible
De-interlace (4CIF resolution)
Compression levels: 100
Rotation: 0°, 180°
Aspect ratio correction
Configurable white balance, exposure control, brightness, sharpness and color mode
Overlay capabilities: Zone ID, preset ID, time, date, PTZ coordinates, text or image
Automatic or manual day/night mode
Backlight compensation
Pan/tilt/zoom
Auto-flip
E-flip
20 preset positions
Sequence mode
Control queue
Image freeze
Supports Windows compatible joysticks
Designed for operator control*
*Not designed for continuous PTZ movements e.g. Guard tour. For continuous movement, please see Axis network
dome offering
41
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
Item
Specification
Shutter time
• NTSC: 4/3 - 1/50000 sec
• PAL: 8/5 - 1/50000 sec
Audio (AXIS 215 PTZ only) Two-way (full or half duplex) or one-way
G.711 PCM 64kbit/s, G.726 ADPCM 32 or 24 kbit/s
Requires external microphone or line in. Mono audio output (line level) connects to PA system or active speaker
with built-in amplifier
Security
Multiple user access levels with password protection
IP address filtering
HTTPS encryption
IEEE 802.1X network access control
Users
20 simultaneous unicast users
Unlimited users using multicast (MPEG-4)
Alarm and event
management
Events triggered by
• built-in multi-window motion detection
• external input (AXIS 215 PTZ only)
• audio detection (AXIS 215 PTZ only)
• temperature
• PTZ preset position
• according to schedule
Image upload over FTP, email and HTTP
Notification over TCP, email, HTTP
Pre- and post alarm buffering in Motion JPEG up to 9 MB (approx 4 min of CIF resolution video at 4 fps)
Connectors
AXIS 215 PTZ
• Ethernet 10BaseT/100BaseTX, RJ-45
• Terminal block for 1 alarm input, 1 output and power out for I/O
• Audio line/mic in
• Audio line out
AXIS 215 PTZ-E
• RJ-45 for 10BASE-T/100BASE-TX
• Pre-installed 5 m (16.4 ft.) Cat-5e cable
Processors and memory
AXIS ETRAX FS 32-bit RISC CPU
AXIS ARTPEC-2 video compression chip
32 MB RAM, 8 MB flash
Battery backed up real-time clock
Power
±
12VDC 5%, max 14.5W
Operating conditions
AXIS 215 PTZ
• 0-45 °C
• Humidity 20 - 80% RH (non-condensing)
AXIS 215 PTZ-E
• -20 to 40 °C (-4 to 104 °F)
• 2 built-in heaters, 3 built-in fans
Temperature warning
Warning issued when temperature is below or above limits
Installation, management
and maintenance
Installation tool on CD and Web-based configuration
Configuration backup and restore
AXIS Camera Station One for recording. AXIS Camera Management for camera management.
Video access from
Web browser
Camera live view for up to 20 clients
Video recording to file (ASF)
Sequence tour for up to 20 Axis video sources
Customizable HTML pages
Minimum web browsing
requirements
• Pentium III CPU 500 MHz or higher, or equivalent AMD,128 MB RAM,
AGP graphics card 32 MB RAM, Direct Draw
• Windows XP, 2000, DirectX 9.0 or later
• Internet Explorer 6.x or later
42
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
Item
Specification
System integration support • Open API for application integration, including AXIS VAPIX API*, AXIS Media Control SDK*,
event trigger data in video stream
• Quality of Service (QoS) Layer 3, DiffServ Model
• Watchdog ensures continuous operation, event notifications can be monitored by other systems
• Embedded Linux operating system
Supported protocols
IPv4/v6, HTTP, HTTPS, SSL/TLS*, TCP, QoS, SNMPv1/v2c/v3 (MIB-II), RTSP, RTP, UDP, IGMP, RTCP, SMTP, FTP, ICMP,
DHCP, UPnP, Bonjour, ARP, DNS, DynDNS, SOCKS, NTP, IEEE 802.1X. More information on protocol usage
*This product includes software developed by the Open SSL Project for use in the Open SSL Tool kit
(www.openssl.org)
Video management
software (not incl.)
AXIS Camera Station – Surveillance application for viewing, recording and archiving up to 25 cameras
Accessories
(included)
• Indoor power supply AXIS PS-P 12VDC
• Hard ceiling and drop ceiling mount kits
• Clear and smoked domes
• Installation Guide
• CD with installation tool, software and User’s Manual
• MPEG-4 licenses (1 encoder, 1 decoder)
• MPEG-4 decoder (Windows)
• 1.5" NPT adapter (AXIS 215 PTZ-E only)
Accessories
(not included)
AXIS 215 PTZ
• Outdoor housing solutions
• Outdoor power supply
• IR illuminators
• AXIS 295 Video Surveillance Joystick
AXIS 215 PTZ-E
Corner mount, pole mount, AXIS 295 Video Surveillance Joystick, AXIS T90A illuminators
Approvals - EMC
• EN55024,
• EN55022 Class B,
• EN61000-3-2,
• EN61000-3-3,
• EN60950-1,
• FCC Part 15 Subpart B Class B,
• ICES-003 Class B,
• C-tick AS/NZS 3548
• Power supply: UL, CSA, CE
Dimensions
(HxWxD) and weight
AXIS 215 PTZ
• 128 x 153 x 131 mm (5.0” x 6.0” x 5.2”) excl. cover
132 x 162 x 149 mm (5.2" x 6.4" x 5.9") incl. hard ceiling cover
• 730g incl. hard ceiling cover
1260g incl. drop ceiling mounting bracket and cover
AXIS 215 PTZ-E
• 4.8 kg (10.6 lb.) incl. cables, excl. wall bracket and sunshield
• 6.1 kg (13.4 lb.) incl. cables, wall bracket and sunshield
43
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
File sizes
The AXIS 215 PTZ/AXIS 215 PTZ-E delivers the following file sizes (PAL):
PAL
Resolution
704x576
704x576
704x288
352x288
176x144
PAL aspect ratio corrected
Min-Max (KB)
10 - 300
10 - 250
5 - 150
Resolution
768x576
768x576
768x288
384x288
192x144
Min-Max (KB)
11 - 330
4CIF
2CIF expanded
2CIF
4CIF
2CIF expanded
2CIF
11 - 270
5.5 - 160
2.7 - 90
CIF
2.5 - 80
1 - 20
CIF
QCIF
QCIF
1.1 - 22
The AXIS 215 PTZ/AXIS 215 PTZ-E delivers the following file sizes (NTSC):
NTSC
Resolution
704x480
704x480
704x240
352x240
176x120
NTSC aspect ratio corrected
Min-Max (KB)
8 - 250
Resolution
640x480
640x480
640x240
320x240
160x120
Min-Max (KB)
7 - 230
4CIF
2CIF expanded
2CIF
4CIF
2CIF expanded
2CIF
8 - 200
7 - 180
4 - 125
3.5 - 110
1.8 - 60
CIF
2 - 70
CIF
QCIF
0.8 - 15
QCIF
0.7 - 14
General performance considerations
When setting up the camera, it is important to consider how various settings and situations will affect
performance. Some factors affect the amount of bandwidth (the bit rate) required, others can affect the frame
rate, and some will affect both. If the load on the CPU reaches its maximum, this will also affect the frame rate.
The following factors are among the most important to consider:
• High image resolutions and/or lower compression levels result in larger images. Bandwidth affected.
• Access by large numbers of Motion JPEG and/or unicast MPEG-4 clients. Bandwidth affected.
• Simultaneous viewing of different streams (resolution, compression, etc.) by many clients. Frame rate
and bandwidth affected.
• Accessing both Motion JPEG and MPEG-4 video streams simultaneously. Frame rate and bandwidth
affected.
• Heavy usage of event settings affects the CPU load. Frame rate affected.
• Enabled motion detection. Frame rate and bandwidth affected.
• Heavy network utilization due to poor infrastructure. Bandwidth affected.
• Viewing on poorly performing client PC lowers perceived performance. Frame rate affected.
• Access by large number of audio clients using full-duplex mode. Bandwidth affected.
Optimizing your system
To see the bandwidth and frame rate currently required by the video stream, the AXIS 215 PTZ/AXIS 215 PTZ-E
provides a tool that can be used to display these values directly in the video image.
To do this, special format strings are added as part of a text overlay.
Simply add #r (average frame rate in fps) and/or #b (average bandwidth
in Kbps) to the overlay.
For detailed instructions, please see the online help for Video & Image >
Overlay Settings, and the help for File Naming & Date/Time Formats.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
Important!
•The figures displayed here are the values as delivered by the camera. If other restrictions are currently in force, (e.g. band-
width limitation) these values might not correspond to those actually received by the client.
•For Motion JPEG, these values will only be accurate as long as no frame rate limit has been specified.
Frame rates - Motion JPEG
The following test results show the frame rates in frames/second (fps) for Motion JPEG streams from the AXIS
215 PTZ/AXIS 215 PTZ-E, using a compression level of 50%. Note that these values are guidelines only - actual
values may vary.
Resolutions
4CIF
60Hz/50Hz
30/25 fps
30/25 fps
30/25 fps
30/25 fps
30/25 fps
2CIF expanded
2CIF
CIF
QCIF
Frame rates - MPEG-4
The following test results show the frame rates in frames/second (fps) for MPEG-4 streams from the AXIS 215
PTZ/AXIS 215 PTZ-E. Note that these values are guidelines only - actual values may vary.
The MPEG-4 test conditions:
• Compression level = 50%
• Video Object Type = Advanced Simple
• GOV structure = IP*
Resolutions
4CIF
60Hz/50Hz
25/21 fps
25/21 fps
30/25 fps
30/25 fps
30/25 fps
2CIF expanded
2CIF
CIF
QCIF
*Note that setting the GOV structure to use “I-frames only” will increase the frame rate.
Bandwidth
As there are many factors affecting bandwidth, it is very difficult to predict the required amounts. The settings
that affect bandwidth are:
• the image resolution
• the image compression
• the frame rate
• the MPEG-4 object type
• the MPEG-4 GOV structure
• the audio settings (AXIS 215 PTZ only)
There are also factors in the monitored scene that will affect the bandwidth. These are:
• the amount of motion
• the image’s complexity
• the lighting conditions.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Technical Specifications
For MPEG-4, if there is only limited bandwidth available, and if this is more important than the image quality,
using a constant bit rate (CBR) is recommended. Use a variable bit rate (VBR) if the image quality needs to be
maintained at a higher level. If supported on the network, consider also using MPEG-4 multicasting, as the
bandwidth consumption will be much lower.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/ AXIS 215 PTZ-E - Glossary of Terms
Resolution.
Glossary of Terms
ActiveX - A standard that enables software components to interact with
one another in a networked environment, regardless of the language(s)
used to create them. Web browsers may come into contact with ActiveX
controls, ActiveX documents, and ActiveX scripts. ActiveX controls are
often downloaded and installed automatically as required.
Client/Server - Client/server describes the relationship between two
computer programs in which one program, the client, makes a service
request from another program, the server, which fulfils the request.
Typically, multiple client programs share the services of a common
server program. A web browser is a client program that requests services
(the sending of web pages or files) from a web server.
CMOS (Complementary Metal Oxide Semiconductor) - A CMOS is a
widely used type of semiconductor that uses both negative and positive
circuits. Since only one of the circuit types is on at any given time,
CMOS chips require less power than chips using just one type of
transistor. CMOS image sensors also allow processing circuits to be
included on the same chip, an advantage not possible with CCD sensors,
which are also much more expensive to produce.
AF (Autofocus) - A system by which the camera lens automatically
focuses on a selected part of the subject.
Angle - The field of view, relative to a standard lens in a 35mm still
camera, expressed in degrees, e.g. 30°. For practical purposes, this is the
area that a lens can cover, where the angle of view is determined by the
focal length of the lens. A wide-angle lens has a short focal length and
covers a wider angle of view than standard or telephoto lenses, which
have longer focal lengths.
Codec - In communications engineering, a codec is usually a
coder/decoder. Codecs are used in integrated circuits or chips that
convert e.g. analog video and audio signals into a digital format for
transmission. The codec also converts received digital signals back into
analog format. A codec uses analog-to-digital conversion and
digital-to-analog conversion in the same chip.
ARP (Address Resolution Protocol) - This protocol is used to associate
an IP address to a hardware MAC address. A request is broadcast on the
local network to discover the MAC address for an IP address.
ARTPEC (Axis Real Time Picture Encoder) - This chip is used for image
compression.
Codec can also mean compression/decompression, in which case it is
generally taken to mean an algorithm or computer program for reducing
the size of large files and programs.
ASIC (Application Specific Integrated Circuit) - A circuit designed for
a specific application, as opposed to a general purpose circuit, such as a
microprocessor.
Compression - See Image Compression.
Aspect ratio - A ratio of width to height in images. A common aspect
ratio used for television screens and computer monitors is 4:3.
High-definition television (HDTV) uses an aspect ratio of 9:16.
Contrast - Defines the degree of difference between the lightest and
darkest parts of an image or video stream.
DC-Iris - This special type of iris is electrically controlled by the
Autoiris (or DC-Iris) - This special type of iris is electrically controlled
by the camera, to automatically regulate the amount of light allowed to
enter.
camera, to automatically regulate the amount of light allowed to enter.
DHCP (Dynamic Host Configuration Protocol) - DHCP is a protocol
that lets network administrators automate and centrally manage the
assignment of Internet Protocol (IP) addresses to network devices in a
network.
AVI (Audio Video Interleave) - A video format that supports
simultaneous playback of audio and video.
Bitmap - A bitmap is a data file representing a rectangular grid of
pixels. It defines a display space and color for each pixel (or "bit") in the
display space. This type of image is known as a "raster graphic." GIFs
and JPEGs are examples of image file types that contain bitmaps.
DHCP uses the concept of a "lease" or amount of time that a given IP
address will be valid for a computer. The lease time can vary, depending
on how long a user is likely to require the network connection at a
particular location.
Because a bitmap uses this fixed raster method, it cannot easily be
rescaled without losing definition. Conversely, a vector graphic image
uses geometrical shapes to represent the image, and can thus be quickly
rescaled.
DHCP also supports static addresses for e.g. computers running web
servers, which need a permanent IP address.
DNS (Domain Name System) - DNS is used to locate and translate
Internet domain names into IP (Internet Protocol) addresses. A domain
name is a meaningful and easy-to-remember name for an Internet
easier to remember than 192.0.34.166. The translation tables for domain
names are contained in Domain name servers.
Bit rate - The bit rate (in kbit/s or Mbit/s) is often referred to as speed,
but actually defines the number of bits/time unit and not distance/time
unit.
Bluetooth - Bluetooth is an open standard for wireless transmission of
voice and data between mobile devices (PCs, handheld computers,
telephones and printers).
Domain Server - Domains can also be used by organizations who wish
to centralize the management of their (Windows) computers. Each user
within a domain has an account that usually allows them to log in to
and use any computer in the domain, although restrictions may also
apply. The domain server is the server that authenticates the users on the
network.
Bonjour - Also known as zero-configuration networking, Bonjour
enables devices to automatically discover each other on a network,
without having to enter IP addresses or configure DNS servers. Bonjour
is a trademark of Apple Computer, Inc.
AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
Duplex - See Full-duplex.
Broadband - In network engineering terms, this describes transmission
methods where two or more signals share the same carrier. In more
popular terminology, broadband is taken to mean high-speed data
transmission.
Ethernet - Ethernet is the most widely installed local area network
technology. An Ethernet LAN typically uses special grades of twisted
pair wires. The most commonly installed Ethernet systems are 10BASE-T
and 100BASE-T10, which provide transmission speeds up to 10 Mbps
and 100 Mbps respectively.
CCD (Charged Coupled Device) - This light-sensitive image device used
in many digital cameras is a large integrated circuit that contains
hundreds of thousands of photo-sites (pixels) that convert light energy
into electronic signals. Its size is measured diagonally and can be 1/4",
1/3", 1/2" or 2/3".
ETRAX (Ethernet Token Ring AXIS) - Axis' own microprocessor.
Factory default settings - These are the settings that originally applied
for a device when it was first delivered from the factory. If it should
become necessary to reset a device to its factory default settings, this
will, for many devices, completely reset any settings that were changed
by the user.
CGI (Common Gateway Interface) - A specification for communication
between a web server and other (CGI) programs. For example, a HTML
page that contains a form might use a CGI program to process the form
data once it is submitted.
Firewall - A firewall works as a barrier between networks, e.g. between
a Local Area Network and the Internet. The firewall ensures that only
authorized users are allowed to access the one network from the other. A
CIF (Common Intermediate Format) - CIF refers to the analog video
resolutions 352x288 pixels (PAL) and 352x240 pixels (NTSC). See also
47
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/ AXIS 215 PTZ-E - Glossary of Terms
firewall can be software running on a computer, or it can be a
standalone hardware device.
bytes) of an image. Two of the most common compressed image formats
are JPEG and GIF.
Focal length - Measured in millimeters, the focal length of a camera
lens determines the width of the horizontal field of view, which in turn is
measured in degrees.
Interlacing - Interlaced video is video captured at 50 pictures (known as
fields) per second, of which every 2 consecutive fields (at half height) are
then combined into 1 frame. Interlacing was developed many years ago
for the analog TV world and is still used widely today. It provides good
results when viewing motion in standard TV pictures, although there is
always some degree of distortion in the image.
FTP (File Transfer Protocol) - An application protocol that uses the
TCP/IP protocols. It is used to exchange files between computers/devices
on networks.
To view interlaced video on e.g. a computer monitor, the video must first
be de-interlaced, to produce progressive video, which consists of
complete images, one after the other, at 25 frames per second. See also
Progressive scan.
Frame - A frame is a complete video image. In the 2:1 interlaced
scanning format of the RS-170 and CCIR formats, a frame is made up of
two separate fields of 262.5 or 312.5 lines interlaced at 60 or 50 Hz to
form a complete frame, which appears at 30 or 25 Hz. In video cameras
with a progressive scan, each frame is scanned line-by-line and not
interlaced; most are also displayed at 30 and 25 Hz.
IP (Internet Protocol) - The Internet Protocol is a method transmitting
data over a network. Data to be sent is divided into individual and
completely independent "packets." Each computer (or host) on the
Internet has at least one address that uniquely identifies it from all
others, and each data packet contains both the sender's address and the
receiver's address.
Frame rate - The frame rate used to describe the frequency at which a
video stream is updated is measured in frames per second (fps). A higher
frame rate is advantageous when there is movement in the video stream,
as it maintains image quality throughout.
The Internet Protocol ensures that the data packets all arrive at the
intended address. As IP is a connectionless protocol, which means that
there is no established connection between the communication
end-points, packets can be sent via different routes and do not need to
arrive at the destination in the correct order.
Full-duplex - Transmission of data in two directions simultaneously. In
an audio system this would describe e.g. a telephone systems.
Half-duplex also provides bi-directional communication, but only in one
direction at a time, as in a walkie-talkie system. See also Simplex.
Gain - Gain is the amplification factor and the extent to which an
analog amplifier boosts the strength of a signal. Amplification factors
are usually expressed in terms of power. The decibel (dB) is the most
common way of quantifying the gain of an amplifier.
Once the data packets have arrived at the correct destination, another
protocol - Transmission Control Protocol (TCP) - puts them in the right
order. See also TCP.
IP Address - An IP address is simply an address on an IP network used
by a computer/device connected to that network. IP addresses allow all
the connected computers/devices to find each other and to pass data
back and forth.
Gateway - A gateway is a point in a network that acts as an entry point
to another network. In a corporate network for example, a computer
server acting as a gateway often also acts as a proxy server and a
firewall server. A gateway is often associated with both a router, which
knows where to direct a given packet of data that arrives at the gateway,
and a switch, which furnishes the actual path in and out of the gateway
for a given packet.
To avoid conflicts, each IP address on any given network must be
unique. An IP address can be assigned as fixed, so that it does not
change, or it can be assigned dynamically (and automatically) by DHCP.
GIF (Graphics Interchange Format) - GIF is one of the most common
file formats used for images in web pages. There are two versions of the
format, 87a and 89a. Version 89a supports animations, i.e. a short
sequence of images within a single GIF file. A GIF89a can also be
specified for interlaced presentation.
An IP address consists of four groups (or quads) of decimal digits
separated by periods, e.g. 130.5.5.25. Different parts of the address
represent different things. Some part will represent the network number
or address, and some other part will represent the local machine address.
See also IP (Internet Protocol).
I-VOP - See VOP.
GOV (Group Of VOPs) - A group of VOPs is the basic unit of an
MPEG-4 video stream. The GOV contains different types and numbers of
VOPs (I-VOPs, P-VOPs, etc) as determined by the GOV length and GOV
structure. See also VOP.
JPEG (Joint Photographic Experts Group) - Together with the GIF file
format, JPEG is an image file type commonly used on the web. A JPEG
image is a bitmap, and usually has the file suffix '.jpg' or ".jpeg." When
creating a JPEG image, it is possible to configure the level of
compression to use. As the lowest compression (i.e. the highest quality)
results in the largest file, there is a trade-off between image quality and
file size.
GOV length - The GOV length determines the number of images (VOPs)
in the GOV structure. See also GOV and VOP.
GOV structure - The GOV structure describes the composition of an
MPEG-4 video stream, as regards the type of images (I-VOPs or P-VOPs)
included in the stream, and their internal order. See also GOV and VOP.
kbit/s (kilobits per second) - A measure of the bit rate, i.e. the rate at
which bits are passing a given point. See also Bit rate.
Half-duplex - See Full-duplex.
HTML (Hypertext Markup Language) - HTML is the set of "markup"
LAN (Local Area Network) - A LAN is a group of computers and
associated devices that typically share common resources within a
limited geographical area.
AXIS COMMUNICATIONS
symbols or codes inserted in a file intended for display in web browser.
<Product Name> Quick User’s Guide
The markup tells the browser how to display the page's words and
images for the user.
Linux - Linux is an open source operating system within the Unix
family. Because of its robustness and availability, Linux has won
popularity in the open source community and among commercial
application developers.
HTTP (Hypertext Transfer Protocol) - HTTP is the set of rules for
exchanging files (text, graphic images, sound, video, and other
multimedia files) on the web. The HTTP protocol runs on top of the
TCP/IP suite of protocols.
MAC address (Media Access Control address) - A MAC address is a
unique identifier associated with a piece of networking equipment, or
more specifically, its interface with the network. For example, the
network card in a computer has its own MAC address.
Hub - A (network) hub is used to connect multiple devices to the
network. The hub transmits all data to all devices connected to it,
whereas a switch will only transmit the data to the device it is
specifically intended for.
Manual iris - This is the opposite to an auto iris, i.e. the camera iris
must be adjusted manually to regulate the amount of light allowed to
reach the image sensor.
IEEE 802.11 - A family of standards for wireless LANs. The 802.11
standard supports 1 or 2 Mbit/s transmission on the 2.4 GHz band. IEEE
802.11b specifies an 11 Mbit/s data rate on the 2.4 GHz band, while
802.11a allows up to 54 Mbit/s on the 5 GHz band.
Mbit/s (Megabits per second) - A measure of the bit rate, i.e. the rate at
which bits are passing a given point. Commonly used to give the "speed"
of a network. A LAN might run at 10 or 100 Mbit/s. See also Bit rate.
Image compression - Image compression minimizes the file size (in
48
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/ AXIS 215 PTZ-E - Glossary of Terms
Monitor - A monitor is very similar to a standard television set, but
lacks the electronics to pick up regular television signals.
This is very useful for IP-Surveillance and remote monitoring
applications in places where it may be too impractical or expensive to
power the device from a power outlet.
Motion JPEG - Motion JPEG is a simple compression/decompression
technique for networked video. Latency is low and image quality is
guaranteed, regardless of movement or complexity of the image. Image
quality is controlled by adjusting the compression level, which in turn
provides control over the file size, and thereby the bit rate.
PPP (Point-to-Point Protocol) - A protocol that uses a serial interface
for communication between two network devices. For example, a PC
connected by a phone line to a server.
PPTP (Point-to-Point Tunnelling Protocol) - A protocol (set of
communication rules) that allows corporations to extend their own
corporate network through private "tunnels" over the public Internet. In
this way a corporation can effectively use a WAN (Wide Area Network)
as a large single LAN (Local Area Network). This kind of interconnection
is known as a virtual private network (VPN).
High-quality individual images from the Motion JPEG stream are easily
extracted. See also JPEG.
Megapixel - See Pixel.
MPEG (Moving Picture Experts Group) - The Moving Picture Experts
Group develops standards for digital video and audio compression. It
operates under the auspices of the International Organization for
Standardization (ISO). The MPEG standards are an evolving series, each
designed for a different purpose.
Pre/post alarm images - The images from immediately before and after
an alarm. These images are stored in a buffer for later retrieval.
Progressive scan - Progressive scan, as opposed to interlaced video,
scans the entire picture, line by line every sixteenth of a second. In other
words, captured images are not split into separate fields as in interlaced
scanning.
MPEG-2 - MPEG-2 is the designation for a group of audio and video
coding standards, and is typically used to encode audio and video for
broadcast signals, including digital satellite and Cable TV. MPEG-2, with
some modifications, is also the coding format used by standard
commercial DVD movies.
Computer monitors do not need interlace to show the picture on the
screen, but instead show them progressively, on one line at a time in
perfect order, i.e. 1, 2, 3, 4, 5, 6, 7 etc., so there is virtually no
"flickering" effect. In a surveillance application, this can be critical when
viewing detail within a moving image, such as a person running. A
high-quality monitor is required to get the best from progressive scan.
See also Interlacing.
MPEG-4 - MPEG-4 is a group of audio and video coding standards and
related technology. The primary uses for the MPEG-4 standard are web
(streaming media) and CD distribution, conversational (videophone), and
broadcast television.
Most of the features included in MPEG-4 are left to individual
developers to decide whether to implement them or not. This means that
there are probably no complete implementations of the entire MPEG-4
set of standards. To deal with this, the standard includes the concept of
"profiles" and "levels", allowing a specific set of capabilities to be
defined in a manner appropriate for a subset of applications.
Protocol - A special set of rules governing how two entities will
communicate. Protocols are found at many levels of communication,
and there are hardware protocols and software protocols.
Proxy server - In an organization that uses the Internet, a proxy server
acts as an intermediary between a workstation user and the Internet.
This provides security, administrative control, and a caching service.
Any proxy server associated with a gateway server, or part of a gateway
server, effectively separates the organization’s network from the outside
network and the local firewall. It is the firewall server that protects the
network against outside intrusion.
Multicast - Bandwidth-conserving technology that reduces bandwidth
usage by simultaneously delivering a single stream of information to
multiple network recipients.
Multiplexer - A multiplexer is a high-speed switch that provides
full-screen images from up to 16 analog cameras. Multiplexers can
playback everything that happened on any one camera with no
interference from the other cameras on the system.
A proxy server receives requests for Internet services (such as web page
requests) from many users. If the proxy server is also a cache server, it
looks in its local cache of previously downloaded web pages. If it finds
the page, it is returned to the user without forwarding the request to the
Internet. If the page is not in the cache, the proxy server, acting as a
client on behalf of the user, uses one of its own IP addresses to request
the page from another server over the Internet. When the requested page
is returned, the proxy server forwards it to the user that originally
requested it.
Network connectivity - The physical (wired or wireless) and logical
(protocol) connection of a computer network or an individual device to a
network, such as the Internet or a LAN.
NTSC (National Television System Committee) - NTSC is the television
and video standard in the United States. NTSC delivers 525 lines at 60
half-frames/second.
PTZ - Pan, tilt and zoom.
P-VOP - See VOP.
NWay is a telecommunications protocol used to automatically negotiate
the highest available transmission speed between network devices. The
NWay protocol is also known as auto-negotiation or auto-sensing.
Resolution - Image resolution is a measure of how much detail a digital
image can hold: the greater the resolution, the greater the level of detail.
Resolution can be specified as the number of pixel-columns (width) by
the number of pixel-rows (height), e.g. 320x240.
OEM (Original Equipment Manufacturer) - This is a designation for
companies that manufacture equipment which is then marketed and sold
to other companies under their own names.
AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
PAL (Phase Alternating Line) - PAL is the dominant television standard
Alternatively, the total number of pixels (usually in megapixels) in the
image can be used. In analog systems it is also common to use other
format designations, such as CIF, QCIF, 4CIF, etc.
in Europe. PAL delivers 625 lines at 50 half-frames/second.
PEM (Privacy Enhanced Mail) - An early standard for securing
electronic mail. The PEM-format is often used for representing an HTTPS
certificate or certificate request.
RTCP (Real-Time Control Protocol) - RTCP provides support for
real-time conferencing of groups of any size within an intranet. This
support includes source identification and support for gateways like
audio and video bridges as well as multicast-to-unicast translators.
Ping - Ping is a basic network program used diagnostically to check the
status of a network host or device. Ping can be used to see if a particular
network address (IP address or host name) is occupied or not, or if the
host at that address is responding normally. Ping can be run from e.g.
the Windows Command prompt or the command line in Unix.
RTCP offers quality-of-service feedback from receivers to the multicast
group as well as support for the synchronization of different media
streams.
Pixel - A pixel is one of the many tiny dots that make up a digital
image. The color and intensity of each pixel represents a tiny area of the
complete image.
RTP (Real-Time Transport Protocol) - RTP is an Internet protocol for
the transport of real-time data, e.g. audio and video. It can be used for
media-on-demand as well as interactive services such as Internet
telephony.
PoE (Power over Ethernet) - Power over Ethernet provides power to a
network device via the same cable as used for the network connection.
RTSP (Real Time Streaming Protocol) - RTSP is a control protocol, and
49
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/ AXIS 215 PTZ-E - Glossary of Terms
a starting point for negotiating transports such as RTP, multicast and
Unicast, and for negotiating codecs.
TCP (Transmission Control Protocol) - TCP is used along with the
Internet Protocol (IP) to transmit data as packets between computers
over the network. While IP takes care of the actual packet delivery, TCP
keeps track of the individual packets that the communication (e.g.
requested a web page file) is divided into, and, when all packets have
arrived at their destination, it reassembles them to re-form the complete
file.
RTSP can be considered a "remote control" for controlling the media
stream delivered by a media server. RTSP servers typically use RTP as
the protocol for the actual transport of audio/video data.
Router - A device that determines the next network point to which a
packet should be forwarded on its way to its final destination. A router
creates and/or maintains a special routing table that stores information
on how best to reach certain destinations. A router is sometimes
included as part of a network switch. See also switch.
TCP is a connection-oriented protocol, which means that a connection is
established between the two end-points and is maintained until the data
has been successfully exchanged between the communicating
applications.
Server - In general, a server is a computer program that provides
services to other computer programs in the same or other computers. A
computer running a server program is also frequently referred to as a
server. In practice, the server may contain any number of server and
client programs. A web server is the computer program that supplies the
requested HTML pages or files to the client (browser).
Telnet - Telnet is a simple method with which to access another network
device, e.g. a computer. The HTTP protocol and the FTP protocols allow
you to request specific files from remote computers, but do not allow
you logon as a user of that computer. With Telnet, you log on as a
regular user with whatever privileges you may have been granted for
specific applications and data residing on that computer.
Sharpness - This is the control of fine detail within a picture. This
feature was originally introduced into color TV sets that used notch filter
decoders. This filter took away all high frequency detail in the black and
white region of the picture. The sharpness control attempted to put some
of that detail back in the picture. Sharpness controls are mostly
superfluous in today's high-end TVs. The only logical requirement for it
nowadays is on a VHS machine.
TVL (TV Lines) - A method of defining resolutions in analog video.
UDP (User Datagram Protocol) - UDP is a communications protocol
that offers limited service for exchanging data in a network that uses the
Internet Protocol (IP). UDP is an alternative to the Transmission Control
Protocol (TCP). The advantage of UDP is that it is not required to deliver
all data and may drop network packets when there is e.g. network
congestion. This is suitable for live video, as there is no point in
re-transmitting old information that will not be displayed anyway.
Simplex - In simplex operation, a network cable or communications
channel can only send information in one direction.
Unicast - Communication between a single sender and a single receiver
over a network. A new connection is established for each new user.
SMTP (Simple Mail Transfer Protocol) - SMTP is used for sending and
receiving e-mail. However, as it is "simple," it is limited in its ability to
queue messages at the receiving end, and is usually used with one of two
other protocols, POP3 or IMAP. These other protocols allow the user to
save messages in a server mailbox and download them periodically from
the server.
URL (Uniform Resource Locator) - An "address" on the network.
USB - (Universal Serial Bus) A plug-and-play interface between a
computer and peripheral devices, e.g. scanners, printers, etc.
Varifocal lens - A varifocal lens provides a wide range of focal lengths,
as opposed to a lens with a fixed focal length, which only provides one.
SMTP authentication is an extension of SMTP, whereby the client is
required to log into the mail server before or during the sending of
email. It can be used to allow legitimate users to send email while
denying the service to unauthorized users, such as spammers.
VPN (Virtual Private Network) - This creates a secure "tunnel" between
the points within the VPN. Only devices with the correct "key" will be
able to work within the VPN. The VPN network can be within a
company LAN (Local Area Network), but different sites can also be
connected over the Internet in a secure way. One common use for VPN
is for connecting a remote computer to the corporate network, via e.g. a
direct phone line or via the Internet.
SNMP (Simple Network Management Protocol) - SNMP forms part of
the Internet Protocol suite, as defined by the Internet Engineering Task
Force. The protocol can support monitoring of network-attached devices
for any conditions that warrant administrative attention.
Sockets - Sockets are a method for communication between a client
program and a server program over a network. A socket is defined as
"the endpoint in a connection." Sockets are created and used with a set
of programming requests or "function calls" sometimes called the
sockets application programming interface (API).
VOP (Video Object Plane) - A VOP is an image frame in an MPEG-4
video stream. There are several types of VOP:
- An I-VOP is complete image frame.
- A P-VOP codes the differences between images, as long as it is more
efficient to do so. Otherwise it codes the whole image, which may also
be a completely new image.
SSL/TSL (Secure Socket Layer/Transport Layer Security)
These two protocols (SSL is succeeded by TSL) are cryptographic
protocols that provide secure communication on a network. SSL is
commonly used over HTTP to form HTTPS, as used e.g. on the Internet
for electronic financial transactions. SSL uses public key certificates to
verify the identity of the server.
WAN (Wide-Area-Network) - Similar to a LAN, but on a larger
geographical scale.
WLAN (Wireless LAN) - A wireless LAN is a wireless local area
network that uses radio waves as its carrier: where the network
connections for end-users are wireless. The main network structure
usually uses cables.
AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
Subnet/subnet mask - A subnet is an identifiably separate part of an
organization's network. Typically, a subnet may represent all the
machines at one geographic location, in one building, or on the same
local area network (LAN). Having an organization's network divided into
subnets allows it to be connected to the Internet with a single shared
network address.
Web server - A Web server is a program, which allows Web browsers
to retrieve files from computers connected to the Internet. The Web
server listens for requests from Web browsers and upon receiving a
request for a file sends it back to the browser.
The subnet mask is the part of the IP address that tells a network router
how to find the subnet that the data packet should be delivered to. Using
a subnet mask saves the router having to handle the entire 32-bit IP
address; it simply looks at the bits selected by the mask.
The primary function of a Web server is to serve pages to other remote
computers; consequently, it needs to be installed on a computer that is
permanently connected to the Internet. It also controls access to the
server whilst monitoring and logging server access statistics.
Switch - A switch is a network device that connects network segments
together, and which selects a path for sending a unit of data to its next
destination. In general, a switch is a simpler and faster mechanism than
a router, which requires knowledge about the network and how to
determine the route. Some switches include the router function. See also
Router.
WEP (Wireless Equivalent Privacy) - A wireless security protocol,
specified in the IEEE 802.11 standard, which is designed to provide a
wireless local area network (WLAN) with a level of security and privacy
comparable to that usually expected of a wired LAN. Security is at two
different levels; 40-bit and 128-bit encryption. The higher the bit
number, the more secure the encryption.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/ AXIS 215 PTZ-E - Glossary of Terms
WINS (Windows Internet Naming Service) - Part of the Microsoft
Windows NT Server, WINS manages the association of workstation
names and locations with IP addresses, without the user or administrator
having to be involved in each configuration change.
WPA-PSK (Wi-Fi Protected Access - Pre-Shared Key) - This wireless
encryption method uses a pre-shared key (PSK) for key management.
Keys can usually be entered as manual hex values, as hexadecimal
characters, or as a Passphrase. WPA-PSK provides a greater degree of
security than WEP.
Zoom lens - A zoom lens can be moved (zoomed) to enlarge the view of
an object to show more detail.
AXIS COMMUNICATIONS
<Product Name> Quick User’s Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Index
Event Servers 23
Event Types 24
Index
4CIF de-interlacing 12
802.1x 28
F
Factory Default 34
File Sizes (NTSC) 44
File Sizes (PAL) 44
FTP Server 23
A
Accessing the video stream 10
Action 23
Action Buttons 19
Active/Inactive 19
Administrator 27
Administrators 11
Advanced Simple profile 8
Full duplex 15
H
Half duplex 15
Host Name 30
HTML Examples 20
HTTP 30
ARP/Ping 29
Audio 15
HTTP Server 23
HTTPS 27
Audio input 15
Audio mode 15
Audio output 16
Auxiliary Power 35
AXIS Media Control 15
AXIS VAPIX API 19
I
Include windows 26
Input 35
IR light 6
L
B
Live View 11
Live View Config 18
Logs & Reports 34
Backup 33
Bit rate 8
Bonjour 32
Brightness 12
Buffer Size 25
Buffers 25
M
Motion JPEG 8
MPEG-4 protocols 9
Multicasting 9
C
CA servers 28
CGI links 19
Color Setting 12
Compression 12
Constant bit rate 8
Control Panel 6
N
NAT Traversal 30
Network 29
New Server Time 29
NTP Configuration 30
NTP Server 29
D
Date & Time 29
Default 33
O
Operator 27
Default Video Format 19
Default Viewer 19
De-interlacing 12
DNS Configuration 30
DNS Server 30
Domain Name 30
DSCP 31
Other MPEG-4 clients 10
Output 35
Output Buttons 19
Overlay Image 13
Overlay Settings 12
Own Home Page 19
Own web files 18
E
Event 23
52
Download from Www.Somanuals.com. All Manuals Search And Download.
AXIS 215 PTZ/AXIS 215 PTZ-E - Index
Upgrade Server 33
UPnP 30, 32
User 27
P
Pan/Tilt/Zoom Control Queue 7
Password 4
Pinout - I/O connectors 35
Port Status 26
User Defined Links 19
User List 27
Ports & Devices 32
Post-trigger Buffer 25
Pre-trigger Buffer 25
PTZ Commands 19
V
VAPIX API 19
Variable bit rate 8
Video Stream 12
Viewer settings 20
Push to talk 15
Q
QoS 31
R
RADIUS 28
Referrals 27
Reset Button 34
Resolution 12
Restart 33
Restore 33
Rotate Image 12
RTP 9
RTP (multicast) 32
RTSP 9
S
Scheduled Event 23, 25
Security 27
Security/Users 27
Sequence Mode 5
Services 29
Setup 11
Shortcuts 6
Simple profile 8
SMTP 31
Snapshot 5
SNMP 32
SOCKS 31
Streaming MPEG-4 9
Support 34
System Options 27
System Overview 34
T
TCP Server 23
Time Mode 29
Troubleshooting 37
U
UDP 9
Unicasting 9
Unit connectors 35
53
Download from Www.Somanuals.com. All Manuals Search And Download.
|