Instruction Manual
Atomic Dual Alarm Clock
model 13024A1
CONTENTS
Unpacking Instructions ........... 2
Package Contents .................. 2
Product Registration ............... 2
Features & Benefits................. 3
Clock Setup........................... 5
Atomic Clock......................... 6
Set the Time & Date ............... 6
Placement Guidelines ............. 7
Using the Clock...................... 8
USB Charging........................ 8
Troubleshooting ..................... 9
Care & Maintenance.............10
Specifications........................10
FCC Information ...................10
Customer Support.................11
Warranty..............................11
Questions? Contact Customer Support at
(877) 221-1252 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Download from Www.Somanuals.com. All Manuals Search And Download.
Features & Benefits
1
FRONT OF CLOCK
1. SNOOZE Button/
Momentary Backlight
INDOOR
2. Alarm #1 ON/OFF Switch
3. Alarm #1 Setup Button
4.
,
&
Buttons
for setup preferences.
5. Alarm #2 Setup Button
6. Alarm #2 ON/OFF Switch
2
3
4
5
6
7
8
BACK OF CLOCK
7. +/—
Brightness Button
Adjusts display brightness.
8. +/—
Alarm Volume
Adjusts alarm volume.
9. USB Charging
for compatible smartphones.
10. Power Adapter Input
9
10
11
12
13
BOTTOM OF CLOCK
(inside battery compartment)
11. RCC ON/OFF Switch
Controls synchronization with
the atomic signal.
12. ºF/ºC Temperature Units
13. RESET Button
Reset to factory defaults.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features & Benefits
1
2
3
9
INDOOR
4
5
7
6
8
1. Date
6. Alarm #2 Time
2. Atomic Clock
7. Alarm #2 Days Active
Sets itself to the correct time and
automatically updates for Daylight
Saving Time.
Indicates alarm set for EVERY DAY,
WEEKDAYS, or WEEKENDS.
8. Alarm Volume
3. Atomic Signal Strength
4. Alarm #1 Time
9. Indoor Temperature
5. Alarm #1 Days Active
Indicates alarm set for EVERY DAY,
WEEKDAYS, or WEEKENDS.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock Setup
Plug in Power Adapter
Install or Replace Backup
Batteries
2
1
For the best performance, plug
in the power adapter as the main
power source for this product.
1. Remove the battery
compartment cover.
2. Insert 3 x AA alkaline
batteries into the battery
compartment, as shown.
Follow the polarity
(+/-) diagram in the battery
compartment.
3. Replace the battery cover.
Plug in Power
1
Adapter
(on back of unit)
Install or
2
Replace Backup
Batteries
3 AA alkaline
batteries
IMPORTANT: Batteries are a backup power source to preserve records in the event of a
power outage. Power adapter recommended as the primary power source to enjoy the full
functionality of the product.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Atomic Clock (RCC)
AcuRite atomic clocks use a radio-controlled signal (RCC) to synchronize to the
correct time broadcast by the National Institute of Standards and Technology
(NIST) Radio Station WWVB, located near Fort Collins, Colorado. WWVB
broadcasts the current time and date with split-second accuracy.
The atomic clock and calendar will maintain the correct time and date, and
automatically update for daylight saving time to provide the most accurate
timekeeping standard possible.
When the RCC button, located under the battery compartment cover, is set to
ON, the clock will automatically search for the atomic clock signal.
To manually search for the atomic signal, make sure the RCC button is set to
ON, then press AND HOLD the “ “ button.
Please note: Signal reception is normally better at night and when the weather
is clear. The atomic signal generally takes a few hours to synchronize, so it is
important to manually set the time and date after powering on the clock.
Set the Time & Date
Press and hold the “ ” button, located on the front of the clock, to enter SET
MODE. Once in SET MODE the preference you are currently setting will blink
on the clock.
To adjust the currently selected (flashing) item, press and release the “ ” or
“
“ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button to adjust the next
preference. The preference set order is as follows:
TIME ZONE (PST MST CST EST AST HAST AKST)
AUTO DST ON/OFF*
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
You will automatically exit SET MODE if no buttons are pressed for 5 seconds.
Enter SET MODE at any time by pressing and holding the “ ” button.
*If you live in an area that observes daylight saving time, DST should be set to
ON.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Clock Placement
Place alarm clock in a dry area free of dirt and dust. To help
ensure an accurate indoor temperature measurement, be sure to
place the clock away from heat sources or vents.
INDOOR
Important Placement Guidelines
• To ensure accurate temperature measurement, place out of direct
sunlight and away from any heat sources or vents.
• To maximize atomic signal reception, place unit away from large metallic
items, thick walls, metal surfaces, or other objects that may limit radio
communication.
• To prevent wireless interference, place unit at least 3 ft (.9 m) away
from electronic devices (TV, computer, microwave, radio, etc.).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Using the Clock
Set the Alarm Time
Slide Alarm #1 and/or Alarm #2 switch ON (alarm time cannot be adjusted if
the alarm is OFF).
1
Press and release the “
MODE.
” or the “
” button to enter ALARM SET
2
To adjust the currently selected (flashing) item, press and release the “ ” or
“ buttons (press and HOLD to fast adjust).
“
To save your adjustments, press and release the “
1” or “
“ button to
2
adjust the next preference. The preference set order is as follows:
ALARM CLOCK HOUR
ALARM CLOCK MINUTE
ALARM EVERY DAY or WEEKDAYS ONLY or WEEKENDS ONLY
You will automatically exit ALARM SET MODE if no buttons are pressed for 5
seconds. Enter ALARM SET MODE at any time by pressing the “ ” or
“ button.
1
“
2
Backlight
During power adapter use, press the Snooze button for momentary backlight
at 100% brightness. During battery-powered use, press any button for
momentary backlight.
The backlight MAY turn off at 2:00 AM and 3:00 AM to acquire the atomic
clock (RCC) signal.
USB Charging
Charge your mobile device by plugging your device’s USB power cord (not
included) into the USB charging port on the back of the clock.
USB charging is only available during power adapter use; USB charging is not
active when operating on battery power only.
Note: Follow the manufacturer’s instructions for your
mobile device(s) to determine compatibility with the USB
charging feature on this product. This product’s USB port
has a maximum output of 5V 1A (1000mA). Some devices
may not support USB charging or may require a higher
power rating than this product provides. Observe the
charging status on your device. Ensure your device is working
properly before attempting to charge.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
• The backlight may automatically turn off for 10 minutes
at 2:00am and 3:00am to acquire the atomic clock
signal.
• Verify power adapter is plugged in.
• Check that the batteries are installed correctly. Batteries
may need to be replaced.
• Increase brightness using +/– buttons, located on the
back of the clock.
Clock is too dark,
hard to read or
doesn’t work
• The optimum viewing angle for this product is from
slightly above it.
• Reset the unit by pressing the reset button, located on
the bottom of the clock.
• Make sure the clock is placed out of direct sunlight and
away from any heat sources or vents
(see page 7).
Inaccurate
temperature
For additional troubleshooting, please visit:
Atomic signal or time
syncing problems
If your AcuRite product does not operate properly after trying
(877) 221-1252 for assistance.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care & Maintenance
Clock Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Specifications
TEMPERATURE RANGE
POWER
32ºF to 122ºF, 0ºC to 50ºC
5v power adapter
3 x AA alkaline batteries (for backup only)
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, There is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
Such modifications could void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Customer Support
AcuRite customer support is committed to providing you with best-in-
class service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(877) 221-1252
24/7 support at www.AcuRite.com
► Installation Videos
► Instruction Manuals
► Replacement Parts
► Register your Product
► Support User Forum
► Submit Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
IMPORTANT
PRODUCT REGISTRATION
Register online
to receive 1 year
warranty protection
www.AcuRite.com
Register a Product
►
Limited One Year Warranty
warranty will not be breached, and Chaney will give no credit
for products it manufactures which have received normal wear
and tear, been damaged (including by acts of nature), tampered,
abused, improperly installed, damaged in shipping, or repaired
or altered by others than authorized representatives of Chaney.
At AcuRite, we proudly uphold our commitment
to quality technology. Chaney Instrument Co.
warrants that all products it manufactures to
be of good material and workmanship, and to
be free of defects when properly installed and
operated for a period of one year from the date
of purchase.
The above-described warranty is expressly in lieu of all other
warranties, express or implied, and all other warranties are
hereby expressly disclaimed, including without limitation the
implied warranty of merchantability and the implied warranty
of fitness for a particular purpose. Chaney expressly disclaims
all liability for special, consequential or incidental damages,
whether arising in tort or by contract from any breach of this
warranty. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation
or exclusion may not apply to you. Chaney further disclaims all
liability from personal injury relating to its products to the extent
permitted by law. By acceptance of any of Chaney’s products,
the purchaser assumes all liability for the consequences arising
from their use or misuse. No person, firm or corporation is
authorized to assume for Chaney any other liability in connection
with the sale of its products. Furthermore, no person, firm or
corporation is authorized to modify or waive the terms of this
paragraph, and the preceding paragraph, unless done in writing
and signed by a duly authorized agent of Chaney. This warranty
gives you specific legal rights, and you may also have other
rights which vary from state to state.
We recommend that you visit us at
your product. However, product registration
does not eliminate the need to retain your
original proof of purchase in order to obtain
warranty benefits.
Chaney Instrument Co. warrants that all products it manufactures
to be of good material and workmanship, and to be free of
defects when properly installed and operated for a period of
one year from the date of purchase. Remedy for breach of this
warranty is limited to repair or replacement of the defective
item(s). Any product which, under normal use and service, is
proven to breach the warranty contained herein within ONE
YEAR from date of sale will, upon examination by Chaney,
and at its sole option, be repaired or replaced by Chaney.
Transportation costs and charges for returned goods shall
be paid for by the purchaser. Chaney hereby disclaims all
responsibility for such transportation costs and charges. This
For in-warranty claims: Chaney Instrument Co.
965 Wells St., Lake Geneva, WI 53147
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s more than accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark
of the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and
copyrights are the property of their respective owners. AcuRite uses patented
Printed in China
13024 INST 090314
Download from Www.Somanuals.com. All Manuals Search And Download.
|